HP gt7720 Thin Client Quick Reference Guide

Add to my manuals
63 Pages

advertisement

HP gt7720 Thin Client Quick Reference Guide | Manualzz

Microsoft

®

Windows Embedded Standard 2009

(WES) and Windows ® XP Embedded (XPe)

Quick Reference Guide

HP thin clients

© Copyright 2008, 2009 Hewlett-Packard

Development Company, L.P.

Microsoft and Windows are U.S. registered trademarks of Microsoft Corporation. Win32,

Windows Internet Explorer, and Windows

Media Player are either registered trademarks or trademarks of Microsoft

Corporation in the United States and/or other countries.

Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems

Incorporated.

The information contained herein is subject to change without notice.

The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.

This document contains proprietary information that is protected by copyright. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of

Hewlett-Packard Company.

Microsoft Windows Embedded Standard

2009 (WES) and Windows XP Embedded

(XPe) Quick Reference Guide

HP thin clients

Second Edition (April 2009)

First Edition (September 2008)

Document Part Number: 502961–002

About This Book

This guide supplements the standard XPe documents supplied by Microsoft Corporation. This document highlights the differences, enhancements, and additional features provided by the latest image with this terminal.

WARNING!

Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life.

CAUTION:

Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information.

NOTE:

Text set off in this manner provides important supplemental information.

iii

iv About This Book

Table of contents

1 For More Information and Updates

2 Introduction

The Desktop ......................................................................................................................................... 3

User Desktop ....................................................................................................................... 3

Administrator Desktop ......................................................................................................... 3

Server Environment Requirements ...................................................................................................... 4

Session Services ................................................................................................................. 4

Citrix ICA ............................................................................................................. 4

Microsoft RDP ..................................................................................................... 5

Terminal Emulation Support ................................................................................ 5

Support Services ................................................................................................................. 5

Altiris Deployment Server .................................................................................... 5

HP Device Manager ............................................................................................ 5

3 Configuration

Logging On ........................................................................................................................................... 6

Automatic Logon .................................................................................................................. 6

Manual Logon ...................................................................................................................... 7

Administrator Logon Access ................................................................................................ 7

Logging Off, Restarting, and Shutting Down the Thin Client ................................................................ 8

Enhanced Write Filter .......................................................................................................... 8

Power Management ............................................................................................................. 9

System Time ........................................................................................................................ 9

Local Drives ........................................................................................................................................ 10

Drive Z ............................................................................................................................... 10

Drive C and Flash .............................................................................................................. 10

Saving Files ....................................................................................................................... 11

Mapping Network Drives .................................................................................................... 11

Roaming Profiles ............................................................................................... 11

User Accounts .................................................................................................................................... 11

Creating a New User Account ........................................................................................... 11

User Manager .................................................................................................................... 11

User Profiles ...................................................................................................................... 12

v

Regional and Language Options ........................................................................................................ 14

Administrative Tools ........................................................................................................................... 15

4 Applications

Symantec Endpoint Protection Firewall .............................................................................................. 17

About the Agent ................................................................................................................. 17

New Features and Functionality ........................................................................................ 18

Microsoft Windows Firewall ................................................................................................................ 18

On-by-Default .................................................................................................................... 18

Configuring Microsoft Windows Firewall ............................................................................ 18

Gathering Configuration Information .................................................................................. 21

Troubleshooting Applications ............................................................................................. 21

Failure Symptoms .............................................................................................................. 21

Resolution .......................................................................................................................... 22

Adding a Program ............................................................................................. 22

Adding a Port .................................................................................................... 22

Citrix Program Neighborhood and PN Agent ..................................................................................... 24

Remote Desktop Connection ............................................................................................................. 25

HP Remote Desktop Protocol (RDP) Multimedia and USB Enhancements ....................................... 27

HP Remote Graphics Software (RGS) Receiver ................................................................................ 27

HP Session Allocation Manager (SAM) Client ................................................................................... 28

Teemtalk Terminal Emulation ............................................................................................................. 29

VMWare View Manager ..................................................................................................................... 29

Altiris Client Agent .............................................................................................................................. 30

HP Management Agent ...................................................................................................................... 32

HP Client Automation Registration and Agent Loading Facility (RALF) ............................................. 32

Microsoft Internet Explorer ................................................................................................................. 33

Windows Media Player 11 .................................................................................................................. 33

5 Control Panel Extended Selections

Enhanced Write Filter Manager .......................................................................................................... 36

Benefits of the Enhanced Write Filter ................................................................................ 36

Enhanced Write Filter Status Service ................................................................................ 36

Enhanced Write Filter GUI ................................................................................................. 37

EWF GUI Buttons .............................................................................................. 38

DOS Command-line Tool Boot Commands ....................................................................... 39

Using Boot Commands ..................................................................................... 39

HP RAMDisk ...................................................................................................................................... 39

HP DHCP Settings Update Client ...................................................................................................... 41

HP ThinState Capture ........................................................................................................................ 42

HP ThinState Deploy ......................................................................................................... 45

HP FTP Image Update ....................................................................................................................... 46

Server Requirements ......................................................................................................... 46

vi

DHCP Server .................................................................................................... 46

FTP Server ........................................................................................................ 46

Description ......................................................................................................................... 46

Host Settings ..................................................................................................................... 47

Select Image to Update ..................................................................................................... 47

6 Administration and Image Upgrades

Altiris Deployment Solution Software ................................................................................................. 49

HP Device Manager ........................................................................................................................... 49

Add-on Upgrades ............................................................................................................................... 49

Image Upgrades ................................................................................................................................. 49

HP FTP Image Update ....................................................................................................................... 50

HP ThinState Capture and Deploy ..................................................................................................... 50

HP Compaq Thin Client Imaging Tool ................................................................................................ 50

HP Client Automation ......................................................................................................................... 50

7 Peripherals

Printers ............................................................................................................................................... 51

Adding Printers Using Generic Text-only Print Driver ........................................................ 51

Using Manufacturer Print Drivers ....................................................................................... 52

HP Universal Print Driver for Thin Clients Add-on ............................................................. 52

Audio .................................................................................................................................................. 52

Index ................................................................................................................................................................... 53

vii

viii

1 For More Information and Updates

HP provides add-ons, Microsoft

®

Quick Fix Engineering updates (QFEs), and periodic updates for thin client images. Check the HP support site for these updates or for important documentation that provides specific information for the image version at http://www.hp.com/support . Select the country from the map, then select See support and troubleshooting information or Download drivers and software

(and firmware). Type the thin client model in the field and click Enter .

1

2 Introduction

HP WES-based thin client models use the Windows Embedded Standard 2009 (WES) operating system.

HP XPe-based thin client models use the Windows XP Embedded (XPe) operating system. This guide provides information pertaining to the latest shipping WES and XPe Service Pack 3 (SP3) images. These thin clients provide the flexibility, connectivity, security, multimedia, and peripheral capabilities that make them ideal for most mainstream business use:

Flexible

Win32

®

-based application support

◦ Extensive peripheral device support

Connectivity

Citrix XenApp Plugin for Hosted Apps, Microsoft Remote Desktop Protocol (RDP), VMware

View Client, HP Session Allocation Client, HP Remote Graphics, and HP TeemTalk

User interface similar to familiar Windows XP Professional

Improved security

Symantec EndPoint Protection Firewall

◦ Microsoft Firewall (Add-on)

Locked down protected Flash drive

● Multimedia

Windows Media ® Player

Windows Musical Instrument Device Interface (MIDI) (Add-on)

● Internet browsing

Windows Internet Explorer ®

Adobe Acrobat ® (Add-on)

Extensive MUI support: English, French, German, Spanish, Dutch, Norwegian, Traditional

Chinese, Simplified Chinese, Korean, and Japanese

HP provides this client “ready to go” out of the box to meet most common customer requirements. You may want to add/remove features using the Add or Remove programs control panel applet or the addons provided on the HP support site, and customize it to specific needs.

2 Chapter 2 Introduction

This guide will introduce you to the features of this client that are not found in the standard Microsoft

Windows XP operating system.

Typically, a terminal is configured locally then used as a template for other terminals, which are then configured using local or remote administration tools.

The Desktop

This section provides a general overview of WES and XPe user and administrator desktop features and functions.

User Desktop

The desktop that displays when you are logged on as a user is a standard WES or XPe desktop, with the exception that the only icons displayed are for the Citrix Program Neighborhood, Microsoft RDP, and Internet Explorer. These selections are also available from the Start menu. You can open the terminal emulator application (HP TeemTalk) from Start > Programs > Hewlett-Packard.

NOTE:

Links to remote Citrix published applications may also be configured to be listed on the Start menu and/or displayed as icons on the desktop. Refer to the Citrix documentation for information and instructions.

For information about the functionality of the standard WES or XPe desktop and Start menu items, refer to the applicable Microsoft documentation: .

● WES— http://msdn.microsoft.com/en-us/embedded/bb981920.aspx0.aspx

XPe— http://msdn2.microsoft.com/en-us/embedded/aa731409.aspx

For information on the Citrix Program Neighborhood or Citrix XenApp, please visit http://www.citrix.com

.

NOTE:

The Control Panel, available by clicking Start > Control Panel, provides access to a limited set of resources for changing WES or XPe user preferences. You must log on as Administrator to access the extended set of Control Panel options and utilities.

Right-clicking the mouse when the pointer is on a user’s desktop background does not open a pop-up menu.

Administrator Desktop

The desktop that displays when you are logged on as an administrator is a standard Windows XP desktop. Icons present on the default administrator desktop Start menu include:

Citrix Program Neighborhood

Microsoft RDP

Internet Explorer

The Desktop 3

NOTE:

Right-clicking the mouse when the pointer is on the administrator’s desktop background opens a pop-up menu.

Server Environment Requirements

HP thin clients use a variety of services accessed through a network. These services include session and product support services as well as standard network services such as DHCP and DNS. Thin clients require the following

Session services

● Support services

Session Services

The network to which the thin client is connected requires any of the following session services:

● Citrix ICA

Microsoft RDP

● Terminal emulation support

Citrix ICA

You can make Citrix Independent Computing Architecture (ICA) available on the network using

Presentation Server and/or XenApp for Microsoft Windows 2000/2003/2008 Server family.

4 Chapter 2 Introduction

Microsoft RDP

The Terminal Services Client application on the thin client accesses Microsoft Terminal Services. You can make Microsoft RDP available on the network using any of the following services:

Microsoft Windows 2000/2003/2008 Server with Terminal Services installed

● Microsoft Windows Server 2000/2003/2008

NOTE:

If a Windows 2000/2003/2008 Server is used for both of these session services (ICA and RDP), a Terminal Services Client Access Licenses TSCAL) server must also reside somewhere on the network. Client Access licenses permit clients to use the terminal, file, print, and other network services provided by Windows 2000/2003/2008 Server. The server grants temporary licenses (on an individual device basis) that are good for 90 days. Beyond that, you must purchase TSCALs and install them in the TSCAL server. You cannot make a connection without a temporary or permanent license.

For additional information about Microsoft Terminal Services, see the Microsoft Web site at http://www.microsoft.com/windows2000/technologies/terminal/default.asp000/technologies/terminal/ default.asp

.

Terminal Emulation Support

All WES- or XPe-based thin client models include terminal emulation software to support computing on legacy platforms. The terminal emulation software uses the Telnet protocol to communicate with the computing platform.

Support Services

Altiris Deployment Server

The Altiris Deployment Solution™ support service is available for the thin client network. This service provides an easy-to-use, integrated tool that allows remote management of thin clients throughout their life cycle, including initial deployment, ongoing management, and software deployment.

You must install the Altiris Deployment Solution on a Windows 2000/2003/2008 Server, or a workstation capable of logging on as administrator to a domain that provides specified network services which can access a software repository for the thin client. The Altiris Deployment Solutions software uses a Preboot

Execution Environment (PXE) session and protocol to reimage or recover the thin client. PXE upgrade services are built into the Altiris Deployment Solution.

For additional information about the Altiris Deployment Solution, refer to the Altiris Web site at http://www.altiris.com/Support/Documentation.aspx

and review the Altiris Deployment Solution User

Guide.

HP Device Manager

HP Device Manager is a thin client focused management tool that is easy to install and use. HP Device

Manager is similar to Altiris and offers many of the same capabilities for managing thin clients. HP Device

Manager, along with Altiris is a key part to HP overall manageability offering, which focuses on allowing the customer to choose the management tool that is most applicable to their environment.

Server Environment Requirements 5

3 Configuration

Logging On

You can log on to the thin client either automatically or manually.

Automatic Logon

The default for the WES- or XPe-based thin client is automatic logon. The administrator can use the HP

Windows Logon Configuration Manager in the Control Panel to enable/disable auto logon and change the auto logon user name, password, and domain. Only the administrator account can change auto logon properties.

NOTE:

To save changes, be sure to disable the write filter cache or right-click on the green write filter

icon and choose commit anytime during the current boot session. See Enhanced Write Filter

Manageron page 36

for information about and instructions for disabling the write filter. Enable the write filter when you no longer want permanent changes.

6 Chapter 3 Configuration

Enabling automatic logon bypasses the Log On to Windows dialog box. To log on as a different user while auto logon is enabled, press and hold Shift while clicking Start > Shut Down > Log Off. This displays the Log On to Windows dialog box and allows you to type in the logon information.

Manual Logon

When automatic logon is disabled, thin client startup displays the Log On to Windows dialog box. Type the logon information in the User Name and Password text boxes. Note the following:

For a user account, the factory-default user name and password are both User.

For an administrator account, the factory-default user name and password are both

Administrator.

For security purposes, HP recommends that you change the passwords from their default values.

An administrator can change passwords by pressing Ctrl+Alt+Del to open the Windows

Security dialog box, and then selecting Change Password. You cannot change the password when logged on as a user.

Passwords are case-sensitive, but user names are not.

The administrator may create additional user accounts using the User Manager utility available in the Administrative Tools option in Control Panel. However, due to local memory constraints, you should keep the number of additional users to a minimum. For more information, see

User

Accounts on page 11

.

Administrator Logon Access

To access Administrator logon regardless of the state of the thin client user mode:

While holding down Shift , click Start > Shut Down. Still holding down Shift , from the Shut Down dialog box, select Log Off, and then click OK.

The screen for Administrator logon is displayed.

NOTE:

The default username and password for the Administrator account is Administrator. The default user name and password for the User account is User.

You can use the HP Windows Logon Configuration Manager to permanently modify the default login user. Located in the Control Panel, only the Administrator can access this application.

Logging On 7

Logging Off, Restarting, and Shutting Down the Thin

Client

To restart, shut down, or log off from the thin client, click Start > Shut Down. From the Shut Down dialog box, select the desired action, and then click OK.

NOTE:

You may also log off or shut down using the Windows Security dialog box. Press Ctrl+Alt

+Del to open the dialog box.

If automatic logon is enabled, when you log off (without shutting down), the thin client immediately logs on the default user set up in Windows Login Configuration. For instructions for logging on as a different user, see

Logging On on page 6 .

The following utilities are affected by logging off, restarting, or shutting down the thin client:

Enhanced Writer Filter

Power Management

System Time

Enhanced Write Filter

For detailed information about the Enhanced Write Filter, see Enhanced Write Filter Manager on page 36 . If you want to save changes to system configuration settings, you must disable the write

filter cache or issue the -commit command during the current boot session. Otherwise, the new settings will be lost when the thin client is shut down or restarted. Enable the write filter when you no longer want to make permanent changes

The write filter cache contents are not lost when you log off and on again (as the same or different user).

You may disable the write filter cache after the new logon and still retain the changes.

Only the administrator has write filter disabling privileges.

8 Chapter 3 Configuration

Power Management

A “Monitor Saver” turns off the video signal to the monitor after a designated idle time, allowing the monitor to enter a power-saving mode. To set power saving options for the monitor, right-click the desktop background and select Properties > Screen Saver > Power.

System Time

After power off, clock time is not lost as long as the power source remains plugged in. You can manually set the local time, or you can automatically set the local time utility to synchronize the thin client clock to a time server at a designated time.

Logging Off, Restarting, and Shutting Down the Thin Client 9

NOTE:

The Windows Time service is Stopped by default. You can Start the service via the administrative tools control panel applet. You may want to Start the service and maintain correct time because some applications may require access to the local thin client time. To open the Date and Time

Properties dialog, click on the time area in the task bar or double-click the Date and Time icon in the

Control Panel.

Local Drives

The following sections describe the local drives located on the thin client.

Drive Z

Drive Z is the onboard volatile memory (MS-RAMDRIVE) on the logic board of the thin client. Because drive Z is volatile memory, HP recommends that you do not use this drive to save data that you want to retain. For RAMDisk configuration instructions, see

HP RAMDisk on page 39

. For information about using the Z drive for roaming profiles, see

Roaming Profiles on page 11 .

Drive C and Flash

Drive C is in the onboard flash drive. HP recommends that you do not write to drive C, as writing to drive

C reduces the free space on the flash.

CAUTION:

If the available free space on the flash drive is reduced to below 10 MB, the thin client becomes unstable.

A write filter is used by the thin client for security and to prevent excessive flash write activity. Changes to the thin client configuration are lost when the thin client is restarted unless the write filter cache is disabled or a -commit command is issued during the current boot session. See the write filter topics in

Enhanced Write Filter Manager on page 36 for instructions to disable the cache. Enable the write

filter when you no longer want permanent changes.

10 Chapter 3 Configuration

Saving Files

CAUTION:

The thin client uses an embedded operating system with a fixed amount of flash memory.

HP recommends that you save files that you want to retain on a server rather than on the thin client. Be careful of application settings that write to the C drive, which resides in flash memory (in particular, many applications by default write cache files to the C drive on the local system). If you must write to a local drive, change the application settings to use the Z drive. To minimize writing to the C drive, update

configuration settings as described in User Accountson page 11

.

Mapping Network Drives

You can map network drives if you log on as Administrator.

To keep the mappings after the thin client is rebooted:

1.

Disable the write filter cache during the current boot session or issue the -commit command.

2.

Select Reconnect at Logon.

Because a user logon cannot disable the write filter cache, you can retain the mappings by logging off the user (do not shut down or restart) and logging back on as Administrator, and then disabling the write filter.

You can also assign the remote home directory by using a user manager utility.

Roaming Profiles

Write roaming profiles to the C drive. The profiles need to be limited in size and will not be retained when the thin client is rebooted.

NOTE:

For roaming profiles to work and be downloaded, there must be sufficient flash space available.

In some cases it may be necessary to remove software components to free up space for roaming profiles.

User Accounts

This section describes how to create a new user account and user profile

Creating a New User Account

CAUTION:

Make sure to disable the write filter cache during the boot session in which a new account is created. Remember to enable the write filter after saving all of the permanent changes to flash.

You must log on as Administrator to create user accounts locally or remotely. Due to local flash/disk space constraints, you should keep the number of additional users to a minimum.

Use the User Manager utility to create new user accounts. To access this utility, click Control Panel

> Administrative Tools.

User Manager

User Manager is a utility that allows the administrator to create, delete, and maintain user accounts.

User Accounts 11

User Profiles

A new user’s profile is based on the Default User profile template, which includes policies similar to the factory-defined User account. This new account will default to membership within the local Users group.

If the Default User profile settings are changed from those set at the factory, the changed settings are automatically applied to any newly user profile—local or domain. Any local accounts created or cached domain accounts logged into this device prior to changes made to the Default User profile are unaffected by these changes—only accounts logged in or cached after the changes.

For a new user to match the characteristics of the pre-defined User account, the Administrator must add the new user to the Power Users group; otherwise the new user will not be able to add a local printer.

The user's actions are still limited while the user is in the Power Users group.

To create the user:

12 Chapter 3 Configuration

CAUTION:

Because of the limited size of flash memory, HP strongly recommends that you configure other applications available to the new and existing users to prevent writing to the local file system. For the same reason, HP also recommends that you exercise extreme care when changing configuration settings of the factory-installed applications.

1.

Log in as Administrator.

2.

Open the Administrative Tools window by clicking Start > Control Panel > Administrative

Tools.

3.

Double-click User Manager to open the Local Users and Groups window.

4.

Double-click the Users folder to view the contents in the right pane.

5.

Click Action in the menu bar, and then select New User. This opens the New User dialog box

6.

Type in the user name and password, and then select the attributes you want.

7.

Click Create, and then click Close.

8.

In the Local Users and Groups window, select the Users folder in the left pane.

9.

In the right pane, double-click the name of the user just created. This opens the [user name]

Properties tabbed dialog box.

10.

Open the Member Of tab dialog

11.

Click Add. This opens the Select Groups dialog box.

12.

Type Power Users in the Enter the Object Names to Select field. This enables the Check

Names command button.

13.

Click Check Names, and then click OK.

The newly created user is now a member of both the Power Users and Users groups and should match the privileges of the default user account.

User Accounts 13

Regional and Language Options

The keyboard language options are preset at the factory. Should you need to make a change, the keyboard language selection is made through the Regional and Language Options selection in the

Control Panel. From this program you can select the type of keyboard you are using as well as the layout/IME settings.

14 Chapter 3 Configuration

Administrative Tools

Click the Administrative Tools icon in the Control Panel to gain access to the available administrative tools:

Administrative Tools 15

4 Applications

The latest WES and XPe images have the following preinstalled applications:

Symantec Endpoint Protection Firewall on page 17

Microsoft Windows Firewall on page 18

Citrix Program Neighborhood and PN Agent on page 24

Remote Desktop Connection on page 25

HP Remote Desktop Protocol (RDP) Multimedia and USB Enhancements on page 27

HP Remote Graphics Software (RGS) Receiver on page 27

HP Session Allocation Manager (SAM) Client on page 28

Teemtalk Terminal Emulation on page 29

VMWare View Manager on page 29

Altiris Client Agent on page 30

HP Management Agent on page 32

HP Client Automation Registration and Agent Loading Facility (RALF) on page 32

Microsoft Internet Explorer on page 33

Windows Media Player 11 on page 33

Access to the following applications is available to all users logon accounts:

Symantec Endpoint Protection Firewall on page 17

Altiris Client Agent on page 30

Additional applications in the form of add-ons are provided and can be downloaded from the HP Web site.

Check the HP support site for these applications or for other important updates or documentation: http://www.hp.com/support . Select the country from the map, then select See support and

troubleshooting information or Download drivers and software (and firmware). Type the thin client model in the field and click Enter .

16 Chapter 4 Applications

Symantec Endpoint Protection Firewall

The HP image includes a Symantec Endpoint Protection Agent Firewall.

About the Agent

The Symantec Endpoint Protection for Windows XPe Agent is security software that is installed on embedded endpoints, such as HP thin clients, that run the WES or XPe operating system.

The agent provides a customizable firewall that protects the endpoint from intrusion and misuse, whether malicious or unintentional. It detects and identifies known Trojan horses, port scans, and other common attacks. In response, it selectively allows or blocks traffic, or various networking services, applications, ports, and components.

The agent uses security policies, which include firewall rules, as well as security settings. These policies protect an individual endpoint from network traffic and the viruses that can cause harm. Firewall rules determine whether the endpoint allows or blocks an incoming or outgoing application or service from gaining access through the network connection. Firewall rules allow the agent to systematically allow or block incoming or outgoing applications and traffic from or to specific IP addresses and ports. Security settings detect and identify common attacks, send e-mail messages after an attack, display customizable messages, and accomplish other related security tasks. Security policies, advanced rules,

Symantec Endpoint Protection Firewall 17

security settings, as well as IPS engine settings have been customized by HP to provide both optimal performance as well as a secure computing environment.

New Features and Functionality

All user accounts can now modify SEP Agent options and settings. Previously the Sygate Agent only granted the Administrator account this ability. User access to firewall settings may now be restricted by configuring an agent password.

Updated command line management options and rules interface replace the legacy Sygate Policy

Editor. Rules and policy changes that would have previously required a stand-alone policy editor may now be made within the agent interface then exported/imported using new command line options. A stand-alone policy editor will not be made available for SEP.

Additional information about the Symantec SEP Firewall is available in the Symantec™ Endpoint

Protection for Windows® Embedded Standard 2009 (WES) and Windows XP Embedded (XPe) User

Guide at: http://www.hp.com/support . Select the country from the map, then click See support and

troubleshooting information. Type the thin client model in the field and click Enter .

Microsoft Windows Firewall

An improved Microsoft Windows Firewall (previously known as Internet Connection Firewall, or ICF) is available from HP as an add-on. The firewall is enabled by default after you install the add-on.

On-by-Default

After you install the add-on, Windows Firewall is turned on by default for all network interfaces. On-bydefault also protects new network connections as they are added to the system. This could break application compatibility if the application by default does not work with stateful filtering.

Configuring Microsoft Windows Firewall

To provide the best security and usability, Windows Firewall provides the ability to add exceptions for applications and services so that they can receive inbound traffic.

To configure Windows Firewall, open the firewall from Control Panel. You can also access the firewall configuration from the Advanced tab in Network Connection properties.

Security Center is not in the image. Once you apply the Windows Firewall, the FIREWALL.CPL control panel applet is only available for the Administrator account.

18 Chapter 4 Applications

NOTE:

After you launch the Windows Firewall add-on, the Control Panel applet is only available to the Administrator account.

General Tab: The General tab provides access to the main three configuration options as shown below.

On (Recommended)

◦ Don’t allow exceptions

Off (Not Recommended)

When you select Don't allow exceptions, Windows Firewall blocks all requests to connect to the computer, including those from programs or services on the Exceptions tab. The firewall also blocks file and printer sharing and discovery of network devices

Using Windows Firewall with no exceptions is useful when connecting to a public network. This setting can help to protect the computer by blocking all attempts to connect to the computer. When you use Windows Firewall with no exceptions, you can still view Web pages, send and receive email, or use an instant messaging program.

Exceptions Tab: Provides the ability to add program and port exceptions to permit certain types of inbound traffic. The exception settings specify the set of computers for which this port/program is open.

Microsoft Windows Firewall 19

You can specify three different modes of access:

◦ Any computer (including those on the Internet)

My network (subnet) only

Custom list

Display a notification when the Windows Firewall blocks a program is selected by default.

You can set a scope for each exception. For home and small office networks, it is recommended that you set the scope to the local network only where possible. This will enable computers on the same subnet to connect to the program on the machine, but drops traffic originating from a remote network.

Advanced Tab: Enables you to configure the following functions.

Network Connection Settings: Select connection-specific rules which apply per network interface.

Security Logging: Create a log file for troubleshooting.

ICMP: With Global Internet Control Message Protocol (ICMP), the computers on a network can share error and status information.

Default Settings: Restore Windows Firewall to a default configuration.

20 Chapter 4 Applications

Gathering Configuration Information

To examine the current policy configuration for Windows Firewall, you can use the following command: netsh firewall show configuration.

Troubleshooting Applications

Modifying an application to work with a stateful filtering firewall is the ideal way to resolve issues. This is not always possible, so the firewall provides an interface for configuring exceptions for ports and applications.

Failure Symptoms

Failures related to the default configuration will manifest in two ways:

Client applications may fail to receive data from a server. Examples include an FTP client, multimedia streaming software, and new mail notifications in some e-mail applications.

● Server applications running on the WES- or XPe-based computer may not respond to client requests. Examples include a Web server such as Internet Information Services (IIS), Remote

Desktop, and File Sharing.

Microsoft Windows Firewall 21

NOTE:

Failures in network applications are not limited to firewall issues. RPC or DCOM security changes can cause failures. It is important to note whether the failure is accompanied by a Windows

Firewall Security Alert indicating that an application is being blocked.

Resolution

With either of the failures mentioned above, you can add exceptions to the configuration for Windows

Firewall. Exceptions configure the firewall to permit specific inbound connections to the computer.

NOTE:

HP recommends adding a program instead of adding a port. Adding a program is easier and safer than adding a port because you do not have to know which port numbers to use, and the port is only open when the program is waiting to receive a connection. Only the specified application can use the port, whereas opening a port allows any application to use it.

Adding a Program

The recommended configuration involves adding a program to the exception list. This solution provides the easiest configuration, as well as enables the firewall to open ranges of ports that can change each time the program runs.

To add a program exception:

1.

Open Windows Firewall and select the Exceptions tab.

2.

If the program is in the list, click to enable the setting. If the program is not in the list, click Add

Program to display the Add a Program dialog box.

3.

Click Browse to choose the program you wish to add as an exception, and then click OK.

4.

Click Change Scope to view or set the scope for the program, and then click OK.

5.

Click OK to close the Add a Program dialog box.

6.

Click the check box to enable the program. By default, the program is not enabled in the list.

Adding a Port

If adding the program to the exception list does not resolve the application issue, you can add ports manually. You must first identify the ports used by the application. The most reliable method for determining port usage is consulting with the application vendor.

22 Chapter 4 Applications

If the port number(s) for the process are less than 1024, it is likely that the port numbers will not change.

If the port numbers used greater than 1024, the application may be using a range of ports, so opening individual ports may not resolve the issue reliably.

Once you have the port number and protocol, add an exception for that port.

To add a port exception:

1.

Open Windows Firewall and click the Exceptions tab.

2.

Click Add Port to display the Add a Port dialog box.

a.

Type the Port Number.

b.

Choose TCP or UDP protocol.

c.

Give the port exception a descriptive name in the Name field.

3.

Click Change Scope to view or set the scope for the port exception, and then click OK.

4.

Click OK to close the Add a Port dialog box.

5.

Click to enable the port.

Microsoft Windows Firewall 23

Citrix Program Neighborhood and PN Agent

Citrix Program Neighborhood is a feature of ICA introduced with MetaFrame 1.8 that enables users to connect to MetaFrame and WinFrame servers and published applications. Program Neighborhood allows complete administrative control over application access and delivers an even greater level of seamless desktop integration.

Alternatively, use PN Agent where Citrix Presentation Server or XenApp is deployed with Web Interface.

PN Agent relies on a central configuration file on the Web Interface server. This client enables placing icons on the desktop or Start menu of the thin client for seamless integration of published applications.

PN Agent can be accessed and started through the Citrix folder in the Start menu.

24 Chapter 4 Applications

Documentation for the ICA client application is available from the Citrix Corporation Web site at www.citrix.com

.

Remote Desktop Connection

Use the Remote Desktop Connection dialog box to establish connections to a Windows Terminal Server or to access remote applications using Microsoft RDP.

Refer to the Microsoft Web site for documentation that offers a detailed explanation and instructions on how to use the Microsoft RDC dialog box.

Remote Desktop Connection 25

26 Chapter 4 Applications

HP Remote Desktop Protocol (RDP) Multimedia and USB

Enhancements

HP Remote Desktop Protocol (RDP) Multimedia and USB Enhancements software enhances your users’ Microsoft Remote Desktop Protocol virtualization experience. HP Remote Desktop Protocol

Enhancements provide users with a single-logon initiated, full-screen virtual desktop experience

(including stereo audio). The client-side software, which is included in the latest WES and XPe images, works seamlessly. Users simply log in on the thin client to take advantage of its multimedia features, such as training videos, and USB device support. For additional information, visit http://bizsupport1.austin.hp.com/bc/docs/support/SupportManual/c01705352/c01705352.pdf/ c01705352.pdf

.

HP Remote Graphics Software (RGS) Receiver

HP Remote Graphics Software (RGS) is a high-performance remote desktop connection protocol that delivers an exceptional remote desktop user experience for rich user environments that include video, web flash animations and graphics intensive applications. All applications run natively on the remote system and take full advantage of the compute and hardware graphics resources of the sending system.

HP RGS captures the desktop of the remote system and transmits it over a standard network to a window on a local client (a receiver) using advanced image compression technology specifically designed for text, digital imagery and high frame rate video applications. The receiver uses their keyboard, mouse, and USB devices to interact with applications just as if they were physically interacting with the sender system providing an interactive, high performance, multi-display desktop experience.

The RGS Receiver is included in the latest HP thin client WES and XPe image. Visit http://www.hp.com/ go/rgs for information on RGS Sender Licensing, installation, and use.

HP Remote Desktop Protocol (RDP) Multimedia and USB Enhancements 27

HP Session Allocation Manager (SAM) Client

The Consolidated Client Infrastructure (CCI) solution from HP centralizes desktop computing and storage resources into easily managed, highly secure data centers, while providing end users the convenience and familiarity of a traditional desktop environment. Additionally, companies have long used server-based computing (SBC) to create virtual instances of desktop applications on a server that multiple remote users can access. HP CCI offers a new alternative for virtualizing the desktop.

Part of the CCI solution is the HP Session Allocation Manager (HP SAM) and is an extension the HP

SAM client. HP SAM client is included in the latest HP Thin Client WES and XPe image, and can be accessed from Start > Programs.

HP SAM becomes the control point in managing a CCI deployment. Specifically, it manages the assignment of Microsoft Remote Desktop connections from a user’s access device (thin client) to

Remote Desktop sessions (blade PCs). Whether the session resides on a dedicated physical blade or resides together with other sessions on a virtual hardware platform, the HP SAM system can make these desktop sessions available to users as they are needed.

For more information about HP SAM, see http://h71028.www7.hp.com/enterprise/cache/

323204-0-0-225-121.html?jumpid=reg_R1002_USEN3204-0-0-225-121.html

.

28 Chapter 4 Applications

Teemtalk Terminal Emulation

All WES- or XPe-based thin client models include terminal emulation software to support computing on legacy platforms. The software uses the Telnet protocol to communicate with the computing platform.

Refer to the terminal emulation documentation (supplied separately) for instructions. By default, you can access the Teemtalk Connection Wizard and the Teemtalk Emulator from Start > All Programs.

VMWare View Manager

View Manager, a key component of VMWare View, is an enterprise class desktop management solution, which streamlines the management, provisioning and deployment of virtual desktops. Users securely and easily access virtual desktops hosted on VMWare Infrastructure, terminal servers, blade PCs or even remote physical PCs through View Manager.

For additional information about VMWare View, see http://www.vmware.com/products/view .

Teemtalk Terminal Emulation 29

Altiris Client Agent

The Altiris Client Agent allows the Altiris server to discover valid clients that are added to the network.

The agent carries out assignments and reports the status of individual thin clients to the Altiris server.

30 Chapter 4 Applications

Altiris Client Agent 31

HP Management Agent

The HP Management Agent is a software component installed on thin client devices so that HP Device

Manager can interact with them. The agent is embedded in the standard thin client WES and XPe image to enable Device Manager to manage devices out-of-the-box (agents on older devices, however, may need to be upgraded).

For additional information concerning the HP Device Manager and the HP Management Agent please check the HP support site for these applications or for other important updates or documentation: http://www.hp.com/support . Select the country from the map, then select See support and

troubleshooting information or Download drivers and software (and firmware). Type the thin client model in the field and click Enter .

HP Client Automation Registration and Agent Loading

Facility (RALF)

RALF configuration and operation

RALF is shipped pre-installed on the latest HP thin client images (except those running ThinConnect).

It is used to register with an HP Client Automation Server (HPCA) so that the full HPCA agent can be pushed down and therefore the thin client be managed by the HP Client Automation console. RALF is configured using a default HPCA Server hostname defined as 'hpcaserver.' While the HPCA server can be installed to match this name, it is more common to use this name as a DNS alias in defining the actual HPCA server host name. The HP Client Automation Standard, Starter, and Enterprise version

7.5 or greater have additional documentation on how RALF can also be re-configured to define a different hostname using the command line options. More information on HP Client Automation can be found at https://h10078.www1.hp.com/cda/hpms/display/main/hpms_content.jsp?

zn=bto&cp=1-11-271-272%5e9783_4000_100__&jumpid=go/clientautomation .

When RALF is installed, it runs as a Windows service or Linux daemon that periodically probes for the

HPCA server. This probing continues for 24 hours, and then RALF will shut down. It starts this 24–hour

32 Chapter 4 Applications

probe again upon reboot. Once the server is contacted, RALF registers the device with the HPCA infrastructure and waits to accept the request to install the HPCA agent. Once the HPDA agent is installed, RALF periodically contacts the server and verifies device registration attributes.

Microsoft Internet Explorer

Version 7.0 of the Microsoft Internet Explorer browser is installed locally on the thin client. The Internet options settings for the browser have been preselected at the factory to limit writing to the flash memory.

These settings prevent exhaustion of the limited amount of flash memory available and should not be modified. You may access another browser through an ICA or RDP account if you need more browser resources.

Microsoft Internet Explorer 7.0 is much more secure. Internet Explorer has more control over the execution of all content, including a built-in facility to manage pop-up windows. Furthermore, Internet

Explorer now prevents scripts from moving or resizing windows and status bars to hide them from view or obscure other windows.

A block unsafe file transfers feature is available with Internet Explorer 7. For a list of files generally considered unsafe, see Information About the Unsafe File List in Internet Explorer 6 on the Microsoft

Web site at http://support.microsoft.com/kb/29136991369 .

Windows Media Player 11

Version 11 of the Windows Media Player contains security, performance, and functionality improvements. For more information about improvements to Windows Media Player, refer to the

Windows Media Player home page at http://www.microsoft.com/windows/windowsmedia/player/11/ default.aspx

.

Microsoft Internet Explorer 33

34 Chapter 4 Applications

5 Control Panel Extended Selections

The Control Panel is accessed by selecting Start > Control Panel.

Some of the extended selections available on the Control Panel are discussed in the following sections.

35

Enhanced Write Filter Manager

WES and XPe include the Enhanced Write Filter (EWF) console application command-line tool,

Ewfmgr.exe. In addition to the DOS command-line tool, the WES and XPe images include an Enhanced

Write Filter GUI. The EWF allows the operating system (OS) to boot from a disk volume residing on any read-only media or write-protected hard drive while appearing to have read/write access to the OS. The

EWF saves all writes to another storage location called an overlay. Changes made to the overlay will not be committed to the flash memory unless the EWF has been disabled or the user performs an intentional commit.

The EWF manager console application can be used to issue a set of commands to the EWF driver, report the status of each protected volume overlay and report the format of the overall EWF configurations.

By including the EWF manager console application component in the configuration and building it into the run-time image, you enable the use of Ewfmgr.exe and the corresponding commands.

Benefits of the Enhanced Write Filter

The EWF provides a secure environment for thin client computing. It does this by protecting the thin client from undesired flash memory writes (flash memory is where the operating system and functional software components reside). The write filter also extends the life of the thin client by preventing excessive flash write activity. It gives the appearance of read-write access to the flash by employing a cache to intercept all flash writes and returning success to the process that requested the I/O.

The intercepted flash writes stored in cache are available as long as the thin client remains active, but will be lost when the thin client is rebooted or shut down. To preserve the results of writes to the registry, favorites, cookies, and so forth, the contents of the cache can be transferred to the flash on demand by the Altiris Deployment Solution software or manually using the Enhanced Write Filter Manager.

After the write filter has been disabled, all future writes during the current boot session are written to the flash, with no further caching until a reboot occurs. The write filter may also be enabled/disabled through the command line. Always enable the writer filter after all of the permanent changes have been successfully made.

The EWF is a powerful tool for any thin client environment in which multiple users have access to the device. The EWF prevents unauthorized users from altering or damaging the image.

Enhanced Write Filter Status Service

This service creates an icon in the System Tray that shows the status of EWF. The EWF Status icon will appear as a red 'lock' when disabled, a green 'lock' when enabled, and a yellow 'lock' when the state is set to change on the next boot.

36 Chapter 5 Control Panel Extended Selections

Status

Red

Green

Yellow

Yellow with Red 'X'

Description

Disabled

Enabled

Commit Mode

Write Filter Corrupted

Example

NOTE:

In the event of a corrupted EWF state, you will need to re-flash the thin client unit with the standard shipping image provided on the web.

If you are logged-on as Administrator, you can change the status of EWF by right-clicking on the icon and selecting the desired EWF state.

NOTE:

Since EWF Manager console utility (ewfmgr.exe) and the EWF status service execute separate code, any status changes by ewfmgr.exe will not be automatically reflected by the EWF status icon.

To refresh the status icon after modifying EWF through ewfmgr.exe, you must right-click on the icon

(you can then click anywhere on the screen to close the context menu). However, any operations made through the EWF status icon menu will be visible through the EWF Manager console application. Status and changes to the Enhanced Write Filter will be synchronized between the EWF status icon and the

EWF Manager Control Panel applet.

Enhanced Write Filter GUI

The EWF GUI can be accessed through the Control Panel or the Administrative Tools option for the administrator.

Enhanced Write Filter Manager 37

To access the EWF GUI, perform the following steps:

1.

Log in as an administrator.

2.

Select Start > Control Panel > Other Control Panel Options or Start > Control Panel >

Administrative Tools.

3.

Click the EWF Manager icon.

4.

Use the EWF GUI to select the Write Filter options.

EWF GUI Buttons

The current version of the EWF GUI includes the following buttons:

Button Description

Enable EWF This button is the same as executing ewfmgr.exe c: -Enable from the DOS prompt.

Disable EWF This button is the same as executing ewfmgr.exe c: -Disable from the DOS prompt.

Overlay

Configuration

This button simply displays the Overlay information and is a combination of the information supplied when executing ewfmgr.exe c: -Description and ewfmgr.exe

c: -Gauge from the DOS prompt.

This button is the same as executing ewfmgr.exe c: -NoCmd from the DOS prompt.

Clear Boot

Command

Commit Data to Volume

This button is the same as executing ewfmgr.exe c: -Commit from the DOS prompt.

38 Chapter 5 Control Panel Extended Selections

NOTE:

When using the Commit boot command, all the temporary contents will be permanently written to the flash memory. In addition, all content accessed (and changes made) after running Commit, but before rebooting the system, will be written to the flash memory as well. This includes changes made during any number of login/logout sessions before the next reboot.

DOS Command-line Tool Boot Commands

The following table lists the EWF boot commands that are supported.

Boot

Command

All

Description

Commit

Disable

Enable

Commitanddis able

Displays information about all protected volumes and performs a command, such as disable, enable, and commit, on each volume if specified.

Commits all current level data in the overlay to the protected volume, and resets the current overlay level to 1 upon shutdown.

Allows user to write to the image after the next reboot.

Prevents the user from writing to the image after the next reboot.

Combination of the Commit and Disable commands. This command will commit data in the overlay upon shutdown. Additionally, EWF will be disabled after the system reboots.

NOTE:

When using the Commit boot command, all the temporary contents will be permanently written to the flash memory. In addition, all content accessed (and changes made) after running Commit, but before rebooting the system, will be written to the flash memory as well. This includes changes made during any number of login/logout sessions before the next reboot.

Using Boot Commands

To use the EWF manager boot commands, type the following syntax in a command prompt:

EWFMGR <drive-letter> —[boot command]

.

NOTE:

Because the EWF manager commands are executed on the next boot, you must reboot the system for the command to take effect.

HP RAMDisk

The RAMDisk is volatile memory space set aside for temporary data storage. It is the Z drive shown in the My Computer window.

HP RAMDisk 39

The following items are stored on the RAMDisk:

Browser Web page cache

Browser history

Browser cookies

Browser cache

Temporary Internet files

Print spooling

User/system temporary files

You can also use the RAMDisk for temporary storage of other data (such as roaming profiles) at the administrator’s discretion (see

Local Drives on page 10

).

Use the RAMDisk Configuration dialog box to configure the RAMDisk size. If you change the size of the

RAMDisk, you will be prompted to restart for changes to take effect. To permanently save the change, make sure to disable the write filter cache or to issue the -commit command during the current boot session before restarting.

NOTE:

The default optimal RAMDisk size is set to 16 MB. The maximum RAMDisk size that you can set is 64 MB. The minimum is 2 MB.

40 Chapter 5 Control Panel Extended Selections

HP DHCP Settings Update Client

The HP DHCP Settings Update Client is a utility found in the Control Panel that allows an IT Administrator to apply some settings to an HP WES or XPe operating system.

The settings are applied through an .INI file that uses a subset of parameters from Microsoft’s sysprep.inf

as well as several XPe/HP-specific keys. XPePrep can run by specifying a local .INI file to be processed, or it can be used in conjunction with DHCP and FTP servers to automatically apply settings across multiple clients on a network.

For detailed information, please review the Using the HP DHCP Settings Update Client document on the HP support site at http://h20000.www2.hp.com/bc/docs/support/SupportManual/c01444724/ c01444724.pdf?jumpid=reg_R1002_USEN4/c01444724.pdf

.

HP DHCP Settings Update Client 41

HP ThinState Capture

The HP ThinState Capture tool is a very simple wizard-based tool that you can use to capture an HP thin client WES or XPe image, which you can then deploy to another HP thin client of identical model and hardware.

What do you need to have?

● An HP WES- or XPe-based thin client that contains the latest HP provided image

An HP-approved USB flash drive (Disk-On-Key). Consult the t5630 quick specs for the latest approved USB flash drives.

WARNING!

By default, the First Boot Device in the F10 System BIOS is first set to USB, then ATA

Flash, and finally to Network boot. If the default Boot order settings have been changed, it is critical before using the HP ThinState Capture tool that you first set the First Boot Device in the Advanced BIOS

Features section of the F10 System BIOS to USB.

NOTE:

The HP ThinState Capture tool is not a standalone tool and can only be accessed by the administrator from within the thin client image.

Save all data on the USB flash drive prior to performing this procedure.

1.

Once you launch the HP ThinState Capture tool from within the Control Panel, you are presented with the following screen.

42 Chapter 5 Control Panel Extended Selections

2.

Click Next.

At this point, attach a disk on key (DOK) to the unit. The DOK drive letter and size are displayed.

The DOK must be greater in size than the onboard flash disk. As a result, if the thin client has 512

MB Flash, then the USB flash drive must be 1 GB.

Once the right DOK size is attached, the following screen displays.

3.

Click Capture. The following warning displays.

4.

Click Yes. The HP ThinState Capture tool formats and makes the USB flash drive bootable. HP

ThinState Capture will now reboot the system.

HP ThinState Capture 43

5.

After you perform these actions, the HP ThinState Capture tool displays the following screen.

Please follow the on-screen instructions.

You can now use the USB flash drive to deploy the captured image to another HP thin client of the exact same model and hardware with equal or greater flash size capacity.

The following table lists the supported capture and deploy scenarios:

Deploy To:

2GB Flash 1GB Flash 512MB Flash

Capture From:

2GB Flash

1GB Flash

512MB Flash

X

X

X

X

X X

44 Chapter 5 Control Panel Extended Selections

HP ThinState Deploy

To perform an HP ThinState deployment:

1.

Set the boot order in the F10 System BIOS to USB boot.

2.

Attach the USB flash drive to the thin client unit you wish to deploy the captured image to, and then power on the unit.

3.

Follow the on-screen instructions.

After you remove the USB flash drive and cycle power to the system, the image will unbundle. This process can take between 10-12 minutes. Do not interrupt or cycle power to the unit during this process.

You may use the captured image (flash.ibr) found in the USB flash drive in combination with Altiris

Deployment or HP Device Manager Solution to remotely image multiple thin client units.

NOTE:

You must use flash.ibr in conjunction with the HP ThinState Deploy utility (e.g., ibr.exe).

Flash.ibr is not compatible with the Altiris rdeploy.exe or rdeployt.exe utilities. Please consult the HP

Compaq Thin Client Imaging Tool white paper at http://h20000.www2.hp.com/bc/docs/support/

SupportManual/c00485307/c00485307.pdf

.

For more information about Altiris, see http://www.altiris.com/ .

HP ThinState Capture 45

HP FTP Image Update

HP FTP Image Update Client is a utility that allows image update from an FTP share to an HP thin client system running WES or XPe operating system.

Server Requirements

DHCP Server

Option 137 should contain a string value specifying an FTP share where the WES or XPe images and

WinPE image are stored.

For example, if the XPe images and WinPE image are stored in ftp://ftpserver/ftpfolder, then the option

DHCP option 137 should contain the following string:

● ftp://username:password@ftpserver/ftpfolder

, if the FTP share is protected

– or –

● ftp://ftpserver/ftpfolder

, if the FTP share allows anonymous access

FTP Server

The WES and XPe images (in .IBR format) and the WinPE image provided by HP must reside in the same folder on the FTP server.

Description

The HP FTP Image Update Client can only be run by an administrator on an HP thin client system which has a license to run the WES or XPe operating system.

46 Chapter 5 Control Panel Extended Selections

NOTE:

FTP Image Update is only provided on the t5630, t5630w, t5730, t5730w, gt7720, and vc4820T thin clients with the latest HP XPe image (5.1.606 or greater). For FTP Image Update to function properly, it requires the following available free space on the client: ~200MB of flash and ~250MB of

RAM. FTP Image Update over wireless is not supported. For greater usage flexibility and to take advantage of this and all features provided in the latest image, HP recommends at least 1 GB of flash and 1 GB of RAM.

Host Settings

There are two ways to specify host settings:

1.

You can manually enter settings by clearing the Get Host Settings from DHCP server check box and typing the appropriate information in the Host ID, Path, User ID, and Password fields.

If the FTP share allows anonymous read access, then you can leave the User ID and Password fields empty.

If the WES or XPe images and WinPE image are stored in the default (root) folder on the FTP server, then you can leave the Path field empty or type / in the field.

2.

Automatically through a DHCP option by selecting the Get Host Settings from DHCP server check box.

These host settings can be saved and committed by clicking on the Save Settings button. When the applet is invoked again, the settings will be retrieved and the corresponding controls are automatically populated.

Select Image to Update

Once the host settings are entered, either manually or automatically through DHCP, then click the

Refresh Image List button to make the applet query the FTP share for all XPe images whose targeted

BIOS families match the one of the current thin client system, and fill in the drop-list combo box to the left of the button. You can choose any of the listed images to update/image the system.

When ready, you can click the Run Image Update Now button to proceed with the image update using the selected image. A confirmation dialog similar to the following is displayed.

Click No to abort the operation. If you click Yes, the HP FTP Image Update Client confirms that the flash drive has at least 200MB free to host the WinPE image. If the flash drive does not, the following error message is displayed.

HP FTP Image Update 47

If the flash device has enough memory, the update client starts the download of the WinPE image, modifies the boot loader to boot to WinPE in the next system restart, and then restarts the system to continue to the WinPE phase.

Once WinPE is loaded, IBRPE is spawned to image the system’s flash drive using the selected image from the FTP share. When the imaging completes, IBRPE automatically restarts the system to enter the

FBA phase.

48 Chapter 5 Control Panel Extended Selections

6 Administration and Image Upgrades

This section highlights and discusses the Remote Administration capabilities and firmware upgrade methods applicable to the thin client.

Altiris Deployment Solution Software

The Altiris Deployment Solution software is a full-featured remote administration tool set. It accesses the thin client through the Altiris remote Agent and PXE server utilities installed on the thin client. Altiris allows you to perform the thin client administration functions (including firmware upgrades) without requiring an administrator to visit the individual thin client sites.

For more information about Altiris, see http://www.altiris.com

.

HP Device Manager

HP Device Manager is a server-based application that provides centralized administration capabilities for HP thin client devices. It accesses the thin client through the HP Management Agent which is embedded in the standard thin client WES or XPe image to enable Device Manager to manage devices out-of-the-box (agents on older devices, however, may need to be upgraded).

For additional information concerning the HP Device Manager and the HP Management Agent please check the HP support site for these applications or for other important updates or documentation: http://www.hp.com/support . Select the country from the map, then select See support and

troubleshooting information or Download drivers and software (and firmware). Type the thin client model in the field and click Enter .

Add-on Upgrades

If you want to install an add-on module, you can use the Altiris Deployment Solution or HP Device

Manager to administer the thin client. Disable/enable the write filter as needed to save the changes.

CAUTION:

If the available free space on the flash memory is reduced to less than 10MB and/or the available system memory is reduced to less than 15MB, the thin client becomes unstable.

NOTE:

For add-on modules to work and be downloaded, there must be sufficient flash space available.

In some cases it may be necessary to remove software components to free up space for add-on modules.

Image Upgrades

The Intel Preboot Execution Environment (PXE) is a protocol that defines interaction between TCP/IP,

DHCP and TFTP to enable a client to download a preboot environment from a server. PXE allows a

Altiris Deployment Solution Software 49

client to boot from a server on a network prior to booting the embedded operating system or the operating system from the local flash module. PXE allows a network administrator to remotely wake up a thin client and perform various management tasks, including loading the operating system and other software onto the thin client from a server over the network. The PXE client is installed on the thin client and the PXE server component is part of the Altiris Deployment Solution suite.

NOTE:

Citrix ICA auto update does not function for the ICA client installed on the thin client; updates are implemented through the standard firmware upgrade process.

HP FTP Image Update

HP FTP Image Update Client is a control panel utility that allows image update from an FTP share to an HP thin client system running WES or XPe operating system. For additional information please go

to HP FTP Image Update on page 46

.

HP ThinState Capture and Deploy

The HP ThinState Capture tool is a very simple wizard based tool that can be used to capture an HP thin client WES or XPe image, which can then be deployed to another HP thin client of identical model and hardware. For more information about the HP ThinState Capture tool, see

HP ThinState Capture on page 42 .

HP Compaq Thin Client Imaging Tool

The HP Compaq Thin Client Imaging Tool is part of the SoftPaq deliverable that contains the original factory image for the HP thin client. You can use this utility to restore the original factory image to the thin client.

This utility allows you to perform the following options:

● Create a bootable flash image on a USB flash device (such as on a disk on key).

Unbundle the image to a directory for use in a custom deployment scenario or PXE image.

For additional information about this utility and its uses, visit the HP Web site at http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00485307/c00485307.pdf

.

HP Client Automation

HP Client Automation is an enterprise-wide client management solution for both physical and virtual clients. In addition to being able to completely manage traditional desktop and notebook PCs, HPCA can also manage thin client devices and the back-end virtual infrastructures they connect to. It significantly reduces the management challenges and complexities of thin client devices and client virtualization technologies by providing automation tools for creating and deploying operating system images, software updates, and tracking hardware assets. By using the same management console and tools for all client devices, HPCA helps customers reduce costs and simplify operations.

For additional information concerning HP Client Automation, see http://www.hp.com/go/easydeploy .

50 Chapter 6 Administration and Image Upgrades

7 Peripherals

Depending on the ports available, the thin client can provide services for USB, serial, parallel, and PCI devices, as long as the appropriate software is installed. Factory-installed software is described in the following section. As they become available, you can install add-ons for other services using the Altiris

Deployment or HP Device Manager solution software. For more information, see

Altiris Client Agent on page 30

and HP Management Agent on page 32 .

For more information about available peripherals, see the model QuickSpecs at http://h10010.www1.hp.com/wwpc/us/en/sm/WF04a/12454-321959-89307-338927-89307.html?

jumpid=re_R295_prodexp/busproduct/computing/thinclients454-321959-89307-338927-89307.html

.

Select the model, select Specifications, and then click the QuickSpec link.

Printers

A generic universal print driver is installed on the thin client to support text-only printing to a locally connected printer. To print full text and graphics to a locally connected printer, install the driver provided by the manufacturer and follow the manufacturer’s instructions. Be sure to disable the write filter cache or run the -commit command to save the installation. You can print to network printers from ICA and

RDP applications through print drivers on the servers.

For additional information, please review the Printing and Imaging Support on HP Compaq Thin

Clients white paper on the HP support site at http://h20000.www2.hp.com/bc/docs/support/

SupportManual/c00739537/c00739537.pdf?jumpid=reg_R1002_USEN .

CAUTION:

If the available free space on the flash memory is reduced to less than 10MB and/or the available system memory is reduced to less than 15MB, the thin client becomes unstable.

NOTE:

Downloading and using printers requires sufficient flash space. In some cases, you may have to remove software components to free up space for printers.

Printing to a locally-connected printer from an ICA or RDP session using the print drivers of the server produces full text and graphics functionality from the printer. To do this, you must install the print driver on the server and the text-only driver on the thin client (see the following section).

Adding Printers Using Generic Text-only Print Driver

Follow these steps to add a printer using the text-only print driver:

1.

Connect the printer to the parallel port.

2.

Choose Printers and Faxes from the Start > Settings menu.

3.

Select Add a Printer to open the Add Printer Wizard.

Printers 51

4.

Click Next in the first panel of the wizard.

5.

Select Local printer configured to this computer.

6.

Verify that the Automatically Detect and Install my Plug and Play Printer check box is not selected.

7.

Click Next.

8.

Select Use the Following Port.

9.

Select the appropriate port from the list, and then click Next.

10.

Choose the manufacturer and model of the printer, and then click Next.

11.

Use the assigned default name or other name for the printer, and then click Next.

12.

Select Do Not Share this Printer, and then click Next.

13.

Choose whether to print a test page, and then click Next.

14.

Click Finish.

Using Manufacturer Print Drivers

Install the driver provided by the manufacturer and follow the manufacturer's instructions. Be sure to disable the write filter or issue the -commit command to save the installation.

HP Universal Print Driver for Thin Clients Add-on

HP has developed a printing add-on for the WES- and XPe-based thin clients; this add-on is a repackaging of the HP Universal Print Driver with changes to make it more suitable for the thin client software environment. For example, due to disk space limitations, the current version is available only in English and with no help files. Go to http://www.hp.com/support . Select the country from the map, then select Download drivers and software (and firmware). Type the thin client model in the field and click Enter . Select the thin client model, then the operating system, and download this add-on.

For the detailed specification, other downloads, and documentation on the original UPD, go to http://www.hp.com/go/upd .

For more information on the HP Universal Print Driver, refer to Thin Client Printing with the HP Universal

Print Driver, a white paper, at http://bizsupport.austin.hp.com/bc/docs/support/SupportManual/ c01237156/c01237156.pdf37156/c01237156.pdf

.

Audio

You can redirect audio from applications to the audio jacks on the thin client. You control the level externally (such as by a 600-ohm potentiometer control) and driving speakers requires a power booster.

You can adjust the volume using the sound icon in the task bar system tray. You can single-click on this icon to open the master volume control or double-click to open the volume control application dialog box.

52 Chapter 7 Peripherals

Index

A

accounts

creating user 11

user 7

add-on modules 49 add-on upgrades 49

adding ports, Microsoft Windows

Firewall 22

adding printers 51

adding programs, Microsoft

Windows Firewall 22

administration 49

Administrative Tools 15

administrator

desktop 3

logon 7

Altiris

Client Agent 16

deployment server 5

Deployment Solution 49

Altiris Deployment Solution 5

Altiris Web site 5, 45

applications 16

audio 52

automatic logon 6

C

changing the password 7

Citrix 16

Citrix ICA 4

Citrix Web site 25

client agent, Altiris 16

Client Automation 16, 50

configuring Windows Firewall 18

Control Panel 35

creating user account 11

D

default passwords 7

deployment server, Altiris 5 deployment solution, Altiris 5

desktop 3 desktop administrator 3 desktop, user 3

Device Manager 5, 16, 49

DHCP server 46

DHCP Settings Update Client 41

disk on key requirements 43

drive C 10 drive Z 10

drives

drive C and flash 10 drive Z 10

E

emulation

Teemtalk Terminal

Emulation 16

terminal 5

Enhanced Write Filter 8

Enhanced Writer Filter

Manager 6

EWF 8

extended selections, control

panel 35

F

failure resolution 22

failure symptoms, Microsoft

Windows Firewall 21

features, thin client 2

filter

Enhanced Write Filter 8

write 10

writer 6

firewall

configuring 18

Microsoft Windows

Firewall 16

Symantec Endpoint

Protection 16

flash drive 10

FTP Image Update

host settings 47 image selection 47

server requirements 46

FTP server 46

H

host settings, FTP Image

Update 47

HP Client Automation 16, 50

HP Compaq Thin Client Imaging

Tool 50

HP Device Manager 5, 16, 49

HP DHCP Settings Update

Client 41

HP FTP Image Update

host settings 47 image selection 47

server requirements 46

HP Management Agent 16

HP RALF 16

HP RAMDisk 10

HP Registration and Agent Loading

Facility 16

HP SAM 16

HP SAM Web site 28

HP Session Allocation

Manager 16

HP support Web site, 16

HP ThinState Capture 42, 50

HP ThinState Deploy 45, 50

HP Universal Print Driver 52

I

ICA 4

Index 53

image capture 42

image deployment 45

image selection, FTP Image

Update 47

image upgrades 49

imaging tool 50

information, Web sites 1

internet 2

Internet Explorer 16

Internet Explorer unsafe file

list 33

L

language options 14

local drives 10

log on as Administrator 7

logging off 8

logon

automatic 6

manual 7

Logon Configuration Manager 6

M

Management Agent 16

manual logon 7

manufacturer print drivers 52

mapping network drives 11

Media Player 16

memory, volatile 10

Microsoft Internet Explorer 16

Microsoft Internet Explorer unsafe

file list 33

Microsoft RDP 5, 16

Microsoft Windows Firewall

adding ports 22 adding programs 22

configuring 18

failure symptoms 21

gathering configuration

information 21

troubleshooting

applications 21

monitor saver 9

multimedia 2

O

on by default 18

P

password 7 password, changing 7

peripherals 51

peripherals, QuickSpecs Web

site 51

PN Agent 16

power management 9

preinstalled applications 16

print driver 52 print drivers 52

printers 51 printers, adding 51

profiles 12

program neighborhood 16

PXE 49

R

RALF 16

RAMDisk 10

RDP 5

receiver, RGS 16

regional language options 14

Registration and Agent Loading

Facility 16

Remote Desktop Connection 16

Remote Desktop Protocol 16

Remote Graphics Software

receiver 16

requirements

disk on key 43

server 4

resolution, network application

failure 22

restarting 8

RGS receiver 16

roaming profiles 10

S

SAM Web site 28

saving files 11

security configuring Microsoft Windows

Firewall 18

Microsoft 16

Microsoft Windows

Firewall 16

Symantec Endpoint Protection

firewall 16

Security Center 18

server

DHCP 46

FTP 46

server requirements 4

server requirements, FTP Image

Update 46

server, Altiris deployment 5

services, session 4

Session Allocation Manager

(SAM) 16

session services 4

shutting down 8

Symantec Endpoint

Protection 16

system time 9

T

Teemtalk Terminal Emulation 16

terminal emulation 5

text-only print driver 51

Thin Client Imaging Tool 50

ThinState Capture 42, 50

ThinState Deploy 45, 50

time utility 9

troubleshooting applications,

Microsoft Windows Firewall 21

U

Universal Print Driver 52

unsafe file list for Internet

Explorer 33

upgrades 49 upgrades, add-on 49 upgrading images 49

USB enhancements 16

user

accounts 7

profiles 12

user desktop 3

User Manager 11

utilities

Client Automation 50

DHCP Settings Update

Client 41

system time 9

Thin Client Imaging Tool 50

Universal Print Driver 52

V

VMWare View Manager 16

volatile memory 10

54 Index

W

Web site

Altiris 45

Citrix 25

HP SAM 28

HP support 16

HP Thin Client Imaging Tool

white paper 45

more information 1

peripheral QuickSpecs 51

WES 3

Windows Media Player 33

Windows XPe 3

WES Web site 3

Windows Firewall 16

Windows Media Player 16

Windows Media Player Web

site 33

Windows XPe Web site 3

write filter 10

writer filter 6

Z

Z drive 10

Index 55

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents