Samsung | BN68-02664A-03 | User's Manual | Samsung BN68-02664A-03 User's Manual

(HDD)
USB1
For the very best picture quality, select HD signal sources and use HDMI cables and
connections. Note that many digital cable programs are not in HD. Check with your video
provider to ensure your are receiving HD signals.
Using an HDMI Cable
HDMI OUT
Connect your TV to your Home Theater or other audio
device to enjoy enhanced sound quality.
Device
Digital Audio connection
USB2
Best Connection
Using an Optical Cable
HDMI IN 4
(HDD)
USB1
DVI OUT
Digital Audio System
OPTICAL
Device
AV IN 2
USB2
AUDIO OUT
HDMI IN 4
Follow the steps below to connect the TV to the stand.
✎✎ Make sure to distinguish between the front and back of the Stand and Guide
Stand when assembling them.
✎✎ Make sure that at least two people lift and move the LCD TV.
✎✎ Lay the product down, with the screen facing up and fasten the screws.
DVD / Blu-Ray player /
Cable Box /
Satellite receiver (STB)
(HDD)
USB1
Very Good Connection
Connecting a PC
Connect your TV to a PC to use it as a Monitor.
HD connection
Using an HDMI Cable
AV IN 2
Component connection (up to 1080p)
1
AUDIO OUT
Using a Component Cable
AUDIO OUT
Using an Audio/Video Cable
AUDIO OUT
COMPONENT OUT
PC
Device
Good Connection
Using an D-Sub Cable
VCR
✎✎ When connecting to AV IN on the back of your TV, attach the video
2
AUDIO OUT
PC
Lowest Quality Connection
Step 5 : Run Plug & Play
When you turn on your TV for the first time, it automatically launches the Plug &
Play function. With Plug & Play, you can select the On Screen Display language,
set the clock mode, and launch the TV’s channel memorizing process. It also
displays connection instructions similar to those in this guide.
Screw
Step 2 : Install the Batteries into the Remote
To install batteries into your remote control, follow these steps:
1.
Lift the cover on the back of the remote upward
as shown in the figure to the right.
2.
Install two AAA batteries.
Language
Replace the cover.
Step 3 : Connect Power and Antenna or Cable
Connect Ant In to:
Use a 75 ohm (round) cable.
✎✎ Most cable systems are Standard (STD) systems. If you are not
sure about what kind of cable system you have, contact your cable
company.
5.
The TV memorizes the available channels. This process can take up to
45 minutes. After the TV has memorized the channels, the Clock Mode
screen appears.
6.
Choose the Clock Mode. Select Auto if you have a digital channel in
your area. Select Manual if you don’t, or if you have a cable or satellite
box. When done, press EnterE button. The Daylight Savings screen
appears.
Plug & Play
the batteries to the diagram in the battery
compartment.
Power Input
If your TV is attached to a cable system and you have no cable box, you
must select your cable system type. If you have Digital cable, you must
select the cable system type for both Analog and Digital. After you
have selected the cable system type, select Start, and then press the
EnterE button on your remote.
To turn on your TV, press the Power button on the remote or press the
Power button on the TV. To run Plug & Play, follow these steps:
Select Language of the OSD.
or
4.
To navigate while Plug & Play is running, press the Up, Down, Left or Right
arrow buttons on your remote. To make a selection, press the EnterE button.
To skip a screen, press the Menu button.
✎✎ Make sure to match the + and - ends of
3.
PC OUT
cable (yellow) to the green jack next to the AV In 1 label. The jack will
not match the color of the video cable (yellow).
VCR / DVD / Blu-ray player / Cable Box /
Satellite receiver
Stand
DVI OUT
VCR / DVD / Blu-ray player / Cable Box
/ Satellite receiver
Audio/Video connection (480i only)
VIDEO OUT
Device
Amplifier / DVD Home Theater
Using an DVI to HDMI Cable
Step 1 : Install the Stand
Using an Audio Cable
DVD / Blu-Ray player / HD Cable Box /
HD Satellite receiver (STB)
AV IN 2
HD connection (up to 1080p)
Getting Started
Analog Audio connection
AUDIO IN
(HDD)
USB1
The HDMI connection carries
digital video and audio.
AV IN 2
Connecting an audio device
HD connection (up to 1080p)
HDMI IN 4
1-800-SAMSUNG (1-800-726-7864)
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park, NJ 07660-2112
Samsung Electronics Canada Inc.
55 Standish Court Mississauga, Ontario L5R 4B2
Call Center hours of operation: Mon-Sun, 9:00 AM -12 AM EST.
To register this product, visit : www.samsung.com/register.
HDMI IN 4
AV IN 2
Connecting an AV device (Blu-ray player, cable/satellite box, etc.)
USB2
Please do not return this unit.
If you have problems operating your
TV, call:
1-800-SAMSUNG (1-800-726-7864)
For web support please visit:
www.samsung.com/support
(HDD)
USB1
STOP
HDMI IN 4
Congratulations on the purchase of your new Samsung TV. Read this
setup guide to get your TV up and running quickly.
USB2
USB2
Step 4 : Connect External Devices
Quick Setup Guide
• Wall cable jack or
• VHF/UHF
Antenna or
• Cable or Satellite
box Ant or Cable
Out
Make sure the AC power cord
is plugged in securely to the
wall outlet and the TV.
English
Español
: English
Français
Changing the Screen Size
Your TV has several screen size options, each designed to work best with specific
types of video input. If you have a cable box or satellite receiver, it may have its own
set of screen sizes as well.
To change the screen size, press the P.Size button on your remote. The first time
you press it, your TV displays the current setting. Thereafter, each time you press the
P.Size button, you change the size of the picture on the screen.
The following sizes are available:
✎✎ If you select Manual, the clock setting screen appears.
U Move E Enter
7.
Select the Daylight Saving Time setting: Off, On, or Auto, and then
press EnterE button.
1.
On the Language screen, select the language for the On Screen Display
(OSD) using your remote control, and then press EnterE button. The
Home Use screen appears.
8.
After the time zone screen, The connection method for best HD screen
quality is displayed. Press Right arrow button on your remote to view each
screen in succession. Press the Blue button to skip this section.
2.
Select Home Use, and then press EnterE button. If you select Store
Demo, the TV will reset your picture and audio settings every 30 minutes. After
you press EnterE button, the Antenna Source screen appears.
9.
The Enjoy your TV screen appears. and then press EnterE button.
3.
Basic Functions
If your TV is only attached to an antenna, select Air. If your TV is only
attached to cable and you have no cable box, select Cable. If your TV is
attached to an antenna and cable with no box, select Auto. When done,
press EnterE button on your remote. The Select Cable System screen
appears.
16:9 Wide screen
Zoom 1
Zoom 2
Wide Fit
4:3 Standard screen
Screen Fit
✎✎ Screen Fit displays a full HD picture covering the entire screen with no cutoff on
any side. It is only available when your TV inputs an HDMI (720p, 1080i, 1080p),
Component (1080i, 1080p), or DTV (over-the-air 1080i) signal.
IMPORTANT: If your TV is attached to a cable or satellite box, skip Steps
3 through 5. After Plug & Play is complete, set your TV to Channel 3 or 4,
according to the directions for your cable or satellite box.
English - 1
[LC450_QSG]BN68-02664A-03Eng.indd 1
2010-08-31 �� 3:48:41
Remote Control Buttons and Functions:
Changing Channels and Adjusting the Volume
✎✎ This is a special remote control for the visually impaired persons and has Braille points on the Power, Channel, Volume buttons.
Channel
Volume
Turns the TV on and off.
Press to switch between the sources (Blu-ray player,
cable box, DVD player, etc.) connected to your TV.
MEDIA.P
MEDIA.P
Adjust the volume by pressing the
y button on the remote.
Change the channels by pressing
the z button on the remote.
Press number buttons for direct access to channels.
✎✎ If your TV is attached to a cable
or satellite box, you change the
channel using the box’s remote.
Return to the previous channel.
Press to select additional digital channels broadcast by
the same station. For example, to select channel 54-3,
press 54, press -, and then press 3.
Change channels.
Adjusts the volume.
Displays the channel list on the screen.
View the Media Play.
You can also change the
A
B
C
channels by pressing the
z buttons
S.MODE
on SLEEP
the front panel of P.MODE
your TVP.SIZE
and adjust the volume by
pressing the y
buttons.
Cut off the sound temporarily.
Displays the main on-screen menu.
MEDIA.P
Displays Favorite Channel Lists on the screen.
Quickly selects frequently used functions.
D
SLEEP
RemoteS.MODE
control sensor
MTS
P.MODE
CC
D
1.
Turn on your TV.
S.MODE
SLEEP
MTS
2.
P.MODE
P.SIZE
CC
Using your remote, press the
Menu button on your remote.
Then, select Setup → Time.
A
B
C
S.MODE: Selects the sound mode.
SLEEP: Setting the Sleep Timer.
3.
MTS: Press to choose stereo, mono or Separate Audio
Program (SAP broadcast).
: controls recording on Samsung recorders with the
Anynet+ feature)
P.SIZE
Power Indicator
MTS
CC
P.MODE: Selects picture mode.
✎✎ Select Auto if you have a digital
P.SIZE: Choose the picture size.
channel in your area and are not
using a cable/sat box.
Changing the Picture Mode
Selecting a Source
Your TV has three preset Picture Modes with factory adjusted settings, each
designed to give you an excellent picture under specific conditions.
To watch a movie on your Blu-ray player or watch your favorite TV show, you must
select the correct source. A source is a device, such as a Blu-ray/DVD player, a
cable/satellite box, antenna or a cable TV input. Sources can be connected to
your TV through the HDMI, DVI, Component,
Composite, or D-sub connections, or through the
Antenna or Cable In connections.
The Picture Modes are listed and described in the table below:
Mode
Description
Dynamic
Brightens picture. For a vibrant, enhanced image in brightly lit or
sunny room.
Standard
For a bright, detailed picture in a normally lit room.
For a studio quality cinema picture in a dimly lit or dark room.
To change the Picture Mode, follow these steps:
To view the signal from a source connected to the
HDMI, DVI, Component, Composite, or D-sub
jack, press the Source button on your remote.
Each time you press the Source button, you
change to a different source.
Viewing the On Screen Menus
1.
Turn on your TV.
2.
Using your remote, press the Menu button on your remote.
Then, select Picture → Mode.
To view the On Screen Menus, follow these steps:
3.
On the Picture Mode menu, use the ◄ or ► on your remote to select
the Picture Mode you want.
1.
4.
Press the Exit button to exit the menu.
With the power on, press the Menu button
on your remote. The main menu appears.
The menu’s left side has the following menu
options: Picture, Sound, Channel,
Setup, Input, Application, and Support.
Clock Set
Select Clock Mode, and then
press the EnterE button.
Set Clock Mode to Manual.
CC: Controls the caption decoder.
Menu
MEDIA.P
2.
Press the ▲ or ▼ button on your remote to
MEDIA.P
select a menu option, and then press the EnterE button.
3.
When done using the menu, press the Exit button on your remote to exit.
B
C
SLEEP
MTS
P.MODE
P.SIZE
CC
B
C
Day
Year
--
--
----
Hour
--
Minute
--
am/pm
--
L Move U Adjust
E Enter
R Return
Select Clock Set, and then press
the EnterE button.
The Clock Set screen appears.
5.
Using the number buttons on your remote, enter the month, day, year, hour,
and minute. Use the ◄ or ► button to move between entry fields.
6.
Press the Return button on your remote when done.
Connecting a USB Device for Media Play
You can enjoy photo, music, and movie files
stored on a USB device by connecting it to the TV
and using the Media Play feature. To connect a
USB device for Media Play, follow these steps:
1.
Turn on your TV.
2.
Connect a USB device
containing photo, music and/or
movie files to the USB jack on
the side of the TV.
When the Application selection
screen appears, press the
EnterE button on your
remote to select Media Play
(USB).
TV Side Panel
USB Drive
MediaPlay
Videos
SUM A Change Device
D View Devices E Enter R Return
D
S.MODE
A
Month
4.
3.
A
[LC450_QSG]BN68-02664A-03Eng.indd 2
C
Before you can use your TV’s On/Off Timer, you must set the clock. To set the
clock, follow these steps:
Exit the menu.
Use these buttons in the Media Play and Anynet+ modes.
Movie
B
Setting the Clock
Return to the previous menu.
(
A
Press to display information on the TV screen.
Use these buttons to select On Screen Menu items and
change menu settings.
Colored buttons for use in the Channel List, Media
Play menu, etc.
D
BN68-02664A-03
D
S.MODE
SLEEP
MTS
P.MODE
P.SIZE
CC
English - 2
2010-08-31 �� 3:48:45
Download PDF