643651C Little Tikes Construct `n Learn Smart Workbench

643651C Little Tikes Construct `n Learn Smart Workbench
3+ YEARS
ADULT SUPERVISION AND BATTERY INSTALLATION REQUIRED
643651C
The Construct ‘n Learn Smart Workbench™
will launch and run on all Android devices
4.3 or higher and all Apple devices running
iOS 7 and above. Devices must support
Bluetooth LE for the app to sync
with the workbench. For a complete list of
compatible devices, please visit
littletikes.com/smartworkbench
Download the Smart Workbench app
using the QR code here, or by visiting
littletikes.com/smartworkbench
WARNING
Please keep this manual as it contains important information.
0617-0-C
© The Little Tikes Company,
an MGA Entertainment company.
LITTLE TIKES® is a trademark of Little Tikes in
the U.S. and other countries. All logos, names,
characters, likenesses, images, slogans, and packaging
appearance are the property of Little Tikes.
Little Tikes Consumer Service
2180 Barlow Road Hudson, Ohio 44236 U.S.A.
1-800-321-0183
Printed in China
8
MGA Entertainment UK Ltd
50 Presley Way
Crownhill
Milton Keynes
MK8 0ES
Bucks, UK
0800 521 558
www.littletikes.com
www.littletikes.co.uk
Visit our website at
www.littletikes.com
to register your product and
to enter our sweepstakes.
(No purchase necessary)
• ADULT ASSEMBLY REQUIRED
• Keep these instructions for future reference.
• Keep long hair and loose apparel away from the rotating drill bit.
• Prior to assembly, this package contains small parts: hardware which is a choking hazard and may contain
sharp edges and sharp points. Keep away from children until assembled.
• This product is intended for indoor family use only.
• This product is indented for use by children ages 3 years and up.
• Do not allow children to sit, stand, play or climb on the top surface. Failure to do so may cause the product
to become unstable.
• IMPORTANT: DO NOT immerse RFID chip items in water. Wash with a damp cloth only.
• Electronic devices to be installed and removed by an adult only.
1
CONTENTS
IMPORTANT INFORMATION
ADULT ASSEMBLY REQUIRED
• Please save sales receipt for proof of purchase.
• Clean the unit with a slightly damp cloth (cold water) and mild soap if necessary.
• Real tools are not recommended for use with this unit or accessories.
• Do not apply ruler sticker to anything other than the work surface, as it may not be removed.
• Always turn the work surface and drill OFF after use to conserve battery power.
• NOTE: If the unit stops working or doesn’t work as it should, remove the batteries for a few minutes and then re-insert them. If there is still a
problem, install new batteries.
• DISPOSAL: Disassemble and dispose of equipment in such a manner that no hazardous conditions such as, but not limited to, small parts and
sharp edges exist at the time the equipment is discarded.
B
A
C
D
H
LIMITED WARRANTY
The Little Tikes Company makes fun, high quality toys. We warrant to the original purchaser that this product is free of defects in materials or
workmanship for one year * from the date of purchase (dated sales receipt is required for proof of purchase). At the sole election of The Little Tikes
Company, the only remedies available under this warranty will be the replacement of the defective part or replacement of the product. This
warranty is valid only if the product has been assembled and maintained per the instructions. This warranty does not cover abuse, accident,
cosmetic issues such as fading or scratches from normal wear, or any other cause not arising from defects in material and workmanship. *The
warranty period is three (3) months for daycare or commercial purchasers. U.S.A and Canada: For warranty service or replacement part information, please visit our website at www.littletikes.com, call 1-800-321-0183 or write to: Consumer Service, The Little Tikes Company, 2180 Barlow
Road, Hudson OH 44236, U.S.A. Some replacement parts may be available for purchase after warranty expires—contact us for details. Outside
U.S.A and Canada: Contact place of purchase for warranty service. This warranty gives you specific legal rights, and you may also have other rights,
which vary from country/state to country/state. Some countries/states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
G
BATTERY SAFETY INFORMATION
E
F
NOT INCLUDED
• Use only size “AA” (LR6) alkaline batteries (4 required) and “AAA” (LR03) alkaline batteries (3 required).
• Charging of rechargeable batteries should only be done under adult supervision.
• Remove rechargeable batteries from the product before recharging.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.
• Be sure to insert the batteries correctly and follow the toy and battery manufacturer’s instruction.
• Always remove exhausted or dead batteries from the product.
• Dispose of dead batteries properly: do not burn or bury them.
• Do not attempt to recharge non-rechargeable batteries.
• Avoid short-circuiting battery terminals.
• Remove batteries before placing the unit into storage for a prolonged period of time.
FCC COMPLIANCE
RFID Chip
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Modifications not authorized by the manufacturer may void users authority to operate this device.
CAN ICES-3 (B)/NMB-3(B).
‘Let’s care for the environment!’
The wheelie bin symbol indicates that the product must not be disposed of with other household waste.
Please use designated collection points or recycling facilities when disposing of the item.
Do not treat old batteries as household waste. Take them to a designated recycling facility.
Accessories with the
symbol contain a RFID chip and interact with the app.
DO NOT immerse RFID chip items in water. Wash with a damp cloth only.
2
7
USAGE AND FEATURES CONTINUED
BATTERY INSTALLATION
Tabletop
7
8
An adult must install fresh alkaline batteries (not included) in the Workbench prior to playing. Here’s how:
1. Using a Phillips screwdriver (not included) remove the screw and battery compartment cover from the top of the work surface.
2. Install four (4) 1.5V AA (LR6) alkaline batteries (not included) making sure the (+) and (-) ends face the proper direction as indicated
inside the battery compartment.
3. Replace the compartment cover and tighten the screw.
NOTE: The included toy screwdrivers will not open or close the battery compartment.
The center of the work surface rotates to help you easily install
vehicle parts.
9
1.5V AA/LR6
1.5V AA/LR6
1.5V AA/LR6
1.5V AA/LR6
4 x AA Batteries
The chassis holder can be folded down to create a flat work surface.
10
CHASSIS
Drill
An adult must install fresh alkaline batteries (not included) in the drill prior to playing. Here’s how:
1. Using a Phillips screwdriver (not included) remove the screw and battery compartment cover from under the drill.
2. Install three (3) 1.5V AAA (LR03) alkaline batteries (not included) making sure the (+) and (-) ends face the proper direction as indicated
inside the battery compartment.
3. Replace the compartment cover and tighten the screw.
NOTE: The included toy screwdrivers will not open or close the battery compartment.
Use the included blueprints to build your vehicle. The chassis will
always be the base of each vehicle. The arrows on the chassis and the
chassis holder should face the left. Vehicle parts are interchangeable
and can be assembled with most of the included tools.
11
The Construct ‘n Learn Smart Workbench™ will launch and run on all
Android devices 4.3 or higher and all Apple devices running iOS 7 and above.
Devices must support Bluetooth LE for the app to sync with the Workbench.
For a complete list of compatible devices, please visit
littletikes.com/smartworkbench
1. Get Started!
Insert your mobile device and slide the support bracket up and
down so that it fits securely to the top of the device. Flip the
locking clip upwards to secure.
App Play
GENERAL TROUBLESHOOTING
Remember to sync the Workbench with the app before every use,
and keep your device near the Workbench as you play!
Download the Smart Workbench app to
your tablet or mobile device
by scanning the QR code, or by visiting
littletikes.com/smartworkbench
643651C
Home Screen
Choose your Activity
Workbench does not turn on
or does not respond
· Make sure batteries are correctly installed.
· Remove batteries and put them back in.
· Install new batteries.
· Keep your device near the Workbench
during play
Workbench behaves erratically
· Remove batteries and put them back in.
· Install new batteries.
App is not syncing or screen freezes
· Close out of app.
· Turn Workbench off, then on, and
reconnect with app.
App not recognizing an object
· Check that it is an item with a RFID chip.
· Be sure the item is placed correctly
on the Workbench.
iOS TROUBLESHOOTING
Device must support Bluetooth 4.0 (LE) technology in order to connect to the unit.
IMPORTANT: Make sure your device is fully charged and has a working Internet connection.
Be sure your Workbench has a fresh set of batteries.
How to Connect
Toggles music
ON/OFF
2. To sync the workbench with the app:
Fig. 2
Proceed
Trophies
Free Play
Turn on your device.
· Be sure that the device’s Bluetooth feature is turned on.
· Launch the Construct ‘n Learn Smart Workbench™ app. The “connecting” screen appears
while connecting to the Workbench (Fig. 1).
· Press the “Connect” button
located on the work surface. A green LED will flash
while it is searching for your device (Fig. 2).
· When connecting screen disappears and the green LED remains solid, you’re connected!
NOTE: If you’re having trouble connecting, select “More Help” for troubleshooting tips (Fig. 3).
Fig. 1
Home
As kids engage in traditional role-play, the app recognizes
and responds to the items they are using with fun animation,
encouraging phrases and interesting facts.
Blueprints
Fig. 3
Follow the on-screen instructions to build your
vehicles with the included tools and parts!
PRESS
3. Update the firmware on your workbench:
Fig. 5
3 x AAA Batteries
1.5V AAA/LR03
• Ensure device’s Bluetooth is enabled and
broadcasting. *See your device’s user
manual for instructions.
• Try turning both device and Workbench
off and on completely.
• Ensure your device has the most current
supported operating system.
• Remember to press and hold the green
“Connect” button on the Workbench until
the LED begins flashing.
• Make sure your device and Workbench
are close to each other.
1.5V AAA/LR03
ANDROID TROUBLESHOOTING
IMPORTANT: Do not turn off the workbench or close the app during the update process.
Device must support Bluetooth 4.0 (LE) technology in order to connect to the unit.
· Once connected, the app will automatically search for a firmware update.
· If the app does not find an update, it will proceed to the home screen.
· If the app finds an available update, it will promp you to “update” or do so at a later time (Fig. 4).
· Tap “Update” to download to your device.
· An “Updating” progress bar will appear to indicate the update status. This may take a few
minutes (Fig. 5).
· Once the update is complete, turn off the Workbench and then turn it back on and re-connect
with the app (Fig. 6).
Fig. 4
Tips for Connecting
1. On your iOS device, go to Settings >
Bluetooth and make sure Bluetooth is
turned on. If you can’t turn on Bluetooth
or you see a spinning gear, restart your
device.
Once the device has restarted:
2. Turn on the Workbench.
3. Launch the app on your device.
4. Press and hold the “Connect” button for
about three seconds.
* The green LED next to the button should
begin blinking.
5. Tap on “Connect to Workbench” on your
device.
6. Allow up to 30 seconds for connection to
be established.
How to Connect
1. Tap the “apps” icon on your Android
device’s home screen.
2. Tap on the Settings icon.
3. Scroll down to Application Manager from
the Application section.
4. Display “All” tab by swiping left or right.
5. Tap on Bluetooth.
6. Tap FORCE STOP button.
7. Tap CLEAR DATA.
Tips for Connecting
• Ensure device’s Bluetooth is enabled and
broadcasting.*See your device’s user
manual for instructions.
• Try turning both device and Workbench
off and on completely.
• Ensure your device has the most current
supported operating system.
• Remember to press and hold the green
“Connect” button on the Workbench
until the LED begins flashing.
• Make sure your device and Workbench
are close to each other.
Fix-It Fast!
Learn how to fix various items by
selecting the tool you would
need to repair it! There are two
play modes: beginner and
advanced.
Fig. 6
BEGINNER
Tool Trivia
Can you tell the difference between
all of the tools in your tool box?
Select beginner or advanced mode
according to your skill level.
ADVANCED
1.5V AAA/LR03
See the enclosed Parent Guide & Instructions for Workbench usage.
6
3
ASSEMBLY
USAGE AND FEATURES
Please follow instructions carefully.
Once assembled, some parts may not be removed.
ADULT ASSEMBLY REQUIRED
1
2
B
C
B
B
SNAP
C
B
B
C
1
2
A
E
A
SLOPE
A
Position the base so that it slopes forward. Slide the back legs (B)
upward through the back of the base (A) until they snap into place.
3
Slide the front legs (C) upward through the front of the base (A)
until they snap into place.
D
Attach two hooks to the top of the backboard to hang the blueprints.
Arrange the blueprints so that they follow the correct assembly order.
3
4
H
Attach the hooks onto the front legs (C) and the backboard (E) to
store your tools. Insert the curved end of the hook first. Then,
press the straight peg down to secure the hooks.
4
SNAP
D
C
C
C
B
A
Snap the front of the work surface (D) onto the front legs (C).
Place the ruler sticker (H) on the front of the work surface (D).
5
Once the front of the work surface (D) is assembled, slide it over
the posts on the back legs (B) until they snap into place.
6
E
SNAP
Gx6
E
F
Move the switch on the drill up or down to choose the
spinning direction of the bit. Then, press the trigger button to
make the drill bit spin!
Change the drill bits by gently pulling one bit out of the drill and
pushing another into the drill until it clicks into place.
5
6
O
REAR VIEW
C
A
C
F
Align the posts on the bottom of the backboard (E) with the
openings on the back legs (B). Then, press the backboard down
to snap it in place.
Snap the backboard (E) into the work surface (D). Then, attach the
device holder (F) to the backboard (E) with six screws (G).
4
Move the switch on the work surface
to low or high volume.
O = Off
= Low Volume
= High Volume
Place the RFID chipped tools onto the right side of the work
surface (F) in the “tool tray” to hear tool sounds.
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising