Samsung HC-P4363W User manual

Add to My manuals
92 Pages

advertisement

Samsung HC-P4363W User manual | Manualzz
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 1
............................................................................................................................
HC-P4363W
.............
√
PROJECTION TELEVISION
Owner’s
Instructions
This device is a Class B digital apparatus.
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 2
Important Warranty Information Regarding
Television Format Viewing
Standard screen format televisions (4:3, the aspect ratio of the screen width to height) are
primarily designed to view standard format full-motion video. The images displayed on them
should primarily be in the standard 4:3 ratio format and constantly moving. Displaying
stationary graphics and images on screen, such as the dark top and bottom letterbox bars
(wide screen pictures), should be limited to no more than 15% of the total television viewing
per week.
Wide screen format televisions (16:9, the aspect ratio of the screen width to height) are
primarily designed to view wide screen format full-motion video. The images displayed on
them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if
your model offers this feature, and constantly moving. Displaying stationary graphics and
images on screen, such as the dark side-bars on non-expanded standard format television video
and programming, should be limited to no more than 15% of the total television viewing per
week.
Additionally, viewing other stationary images and text such as stock market reports, video
game displays, station logos, web sites or computer graphics and patterns, should be limited as
described above for all televisions. Displaying any stationary images that exceed the above
guidelines can cause uneven aging of picture tubes (CRTs) that leave subtle, but permanent
burned-in ghost images in the television picture. To avoid this, vary the programming and
images, and primarily display full screen moving images, not stationary patterns or dark
bars. On television models that offer picture sizing features, use these controls to view the
different formats as a full screen picture.
Be careful in the selection and duration of television formats used for viewing. Uneven CRT
aging as a result of format selection and use, as well as other burned-in images, is not covered
by your Samsung limited warranty.
2
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 3
CONTENTS
Chapter 1: Your New TV
List of Features........................................................................................................................
Accessories..............................................................................................................................
Familiarizing Yourself with Your New TV ..............................................................................
Control Buttons ........................................................................................................
Using a Display Deck ................................................................................................
Connection Jacks (Side or Front) ..............................................................................
Connection Jacks (Rear) ............................................................................................
Remote Control (TV Funtions)..................................................................................
Remote Control (DVD and Extra Funtions) ..............................................................
5
5
6
6
7
7
8
9
10
Chapter 2: Installation
Connecting VHF and UHF Antennas ......................................................................................
Antennas with 300-ohm Flat Twin Leads ..................................................................
Antennas with 75-ohm Round Leads ........................................................................
Separate VHF and UHF Antennas ............................................................................
Connecting Cable TV..............................................................................................................
Cable without a Cable Box ........................................................................................
Cable with a Cable Box that Descrambles All Channels ............................................
Connecting to a Cable Box that Descrambles some Channels ..................................
Connecting a VCR ..................................................................................................................
Connecting a Second VCR to Record from the TV ....................................................
Connecting a DVD Player ......................................................................................................
Connecting to Y, PB, PR ............................................................................................
Connecting to Regular Audio and Video Jacks ..........................................................
Connecting a Digital TV Set-Top Box......................................................................................
Connecting to Y, PB, PR ............................................................................................
Connecting to DVI (Digital Visual Interface) ............................................................
Connecting to HDMI (High Definition Multimedia Interface) ..................................
Connecting a Camcorder ........................................................................................................
Connecting to the Digital Audio Input....................................................................................
Connecting Additional Speakers ............................................................................................
Installing Batteries in the Remote Control ..............................................................................
11
11
11
11
12
12
12
13
14
14
15
15
15
16
16
17
17
18
18
19
19
Chapter 3: TV Operation
Turning the TV On and Off ....................................................................................................
Plug & Play Feature ................................................................................................................
Viewing the Menus and On-Screen Displays ..........................................................................
Viewing the Menus....................................................................................................
Viewing the Display ..................................................................................................
Selecting a Menu Language ....................................................................................................
Selecting the Antenna Input....................................................................................................
Adjusting the Screen Automatically (Self Focus) ....................................................................
Deactivating the Automatic Execution of the Self Focus............................................
Removing the “Self Focus” Message from the Display ..............................................
Memorizing the Channels ......................................................................................................
Selecting the Video Signal Source..............................................................................
Storing Channels in Memory Automatically ..............................................................
Changing Channels ................................................................................................................
Using the Channel Buttons........................................................................................
Using the Number Buttons........................................................................................
Using the Previous Channel ......................................................................................
Adding and Erasing Channels ................................................................................................
Selecting Your Favorite Channels ............................................................................................
To Store Your Favorite Channels ..............................................................................
To View Your Favorite Channels................................................................................
Labeling the Channels ............................................................................................................
Scanning the Channels............................................................................................................
Fine Tuning Channels ............................................................................................................
Using Automatic Picture Settings ............................................................................................
Customizing the Picture..........................................................................................................
Selecting the Color Tone ........................................................................................................
Changing the Picture Size ......................................................................................................
Digital Noise Reduction ..........................................................................................................
20
20
22
22
22
23
23
24
25
25
26
26
27
28
28
28
28
29
30
30
30
31
32
33
34
35
36
37
38
3
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 4
CONTENTS
Chapter 3: TV Operation
(continued)
Viewing Picture-In-Picture ......................................................................................................
Activating the PIP......................................................................................................
Selecting an External Source ....................................................................................
Swapping the Sub picture and Main picture ............................................................
Changing the Size of the Sub picture ........................................................................
Changing the Location of the Sub picture ................................................................
Selecting a Signal Source for the Sub picture ............................................................
Changing the Channel of the Sub picture ................................................................
Freezing the Picture ................................................................................................................
Adjusting the Volume..............................................................................................................
Using the MUTE Button..........................................................................................................
Using Automatic Sound Settings ............................................................................................
Customizing the Sound ..........................................................................................................
Choosing a Multi-Channel Sound (MTS) track ......................................................................
Auto Volume ..........................................................................................................................
Setting the Dolby Digital ........................................................................................................
Enjoying Dolby Surround Sound ..............................................................................
Setting the Dynamic Range........................................................................................
Adjusting Speaker Levels ..........................................................................................
Adjusting the Time Delay for Surround Sound Speakers ..........................................
Selecting a Digital Audio Source ............................................................................................
Setting the Clock Manually ....................................................................................................
Setting the Clock Automatically ..............................................................................................
Setting the Sleep Timer ..........................................................................................................
Setting the On/Off Timer ........................................................................................................
Setting the Blue Screen Mode..................................................................................................
Viewing Closed Caption Information ......................................................................................
Setting the On/Off Melody ......................................................................................................
Using the V-Chip (USA)..........................................................................................................
How to Change Your Password ................................................................................
How to Enable/Disable the Rating Controls ..............................................................
How to Set up Restrictions Using the “TV Parental Guidelines” ................................
How to Set up Restrictions Using the “MPAA Rating” ..............................................
Important Notes About Parental Locks......................................................................
Viewing an External Signal Source ..........................................................................................
Setting the Signal Source ........................................................................................
Assigning Names to External sources ........................................................................
Customizing Your Remote Control..........................................................................................
Setting Up Your Remote Control to Operate Your VCR
(Cable box or DVD player)........................................................................................
Remote Control Codes ..............................................................................................
39
39
40
40
40
41
41
42
42
43
43
44
45
46
47
48
48
49
49
50
51
52
53
55
56
57
58
59
60
60
61
62
63
64
65
65
66
67
67
68
Chapter 4: DVD Operation
Playing a Disc ........................................................................................................................
Using the Search and Skip Functions......................................................................................
Using the Play Function..........................................................................................................
Using the Disc Menu ..............................................................................................................
Using the Title Menu ..............................................................................................................
Displaying the Disc Information ............................................................................................
Using the Zoom Function (DVD/VCD) ..................................................................................
Changing the Camera Angle ..................................................................................................
Using the Bookmark Function (DVD/VCD) ............................................................................
Repeat Play ............................................................................................................................
Program Play (CD)..................................................................................................................
Setting up the Language for Player Menu................................................................................
Setting up the Display Options ..............................................................................................
Setting up the Parental Control ..............................................................................................
69
71
72
76
76
77
78
78
79
80
81
82
83
84
Chapter 5: Troubleshooting
Identifying Problems ..........................................................................................................
86
Appendix
Cleaning and Maintaining Your TV ....................................................................................
Using Your TV in Another Country ....................................................................................
Specifications ......................................................................................................................
4
88
88
88
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 5
Chapter One
YOUR NEW TV
List of Features
Your TV was designed with the latest technology. This TV is a high-performance unit that
includes the following special features:
• Easy-to-use remote control
• Easy-to-use on-screen menu system
• Automatic timer to turn the TV on and off
• Adjustable picture and sound settings that can be stored in the TV’s memory
• Automatic channel tuning for up to 181 channels
• A special filter to reduce or eliminate reception problems
• Fine tuning control for the sharpest picture possible
• A built-in multi-channel sound decoder for stereo and bilingual listening
• Built-in, dual channel speakers
• A special sleep timer
• Picture-In-Picture capability that lets you watch two channels at once
• Component Video Input jacks to obtain a sharper image from external sources
• Self Focus
• Digital Inputs
DVI - Digital Visual Interface
HDMI - High Definition Multimedia Interface
• DTS digital output for DTS-enhanced DVDs.
• Playback MP3, JPG, WMA, MPG files from CD-ROM.
Discs which cannot be played: DVD-ROM, CD-ROM, CDI, HD layer of super Audio
CD, CDGs play audio only, not graphics, CDV
Accessories
Once you have unpacked your TV, check to make sure that you have all the parts shown here.
If any piece is missing or broken, call your dealer.
Audio/Video Cable
(AA39-00006A)
Remote Control
(BP59-00065A)/
AAA Batteries
(4301-000103)
Owner’s Instructions (1)/
Safety Guide Manual (1)/
Quick Guide Manual (1)
Warranty Cards (2)/
Registration Card (1)
Holder-Caster
(BP61-00447C)
5
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 6
YOUR NEW TV
Familiarizing Yourself with Your New TV
Control Buttons
You can control your TV’s basic features, including the on-screen menu. To use the more
advanced features, you must use the remote control.
ΠPOWER
Press to turn the TV on and off.
´ Stand-By Indicator
Lights up when you turn the power off.
- Power Off ; Red
- Power On ; Off
- Timer On ; Green
ˇ Remote Control Sensor
Aim the remote control towards this spot on the TV.
6
∏
CH
Press to change channels and move between items
on the on-screen menu.
”
(Enter)
While using the on-screen menus, press to activate
(or change) a particular item.
’
,
Press to skip or search the title, chapter or track.
˝
Press to stop the disc.
¨ SOURCE
Press to switch between viewing TV programs and
signals from connected components.
Ô
ˆ MENU
Press to see an on-screen menu of your TV's features.

Ø + VOL –
Press to lower or raise the volume and to select items
when using the on-screen menu
Ò Disk Tray
Load the disc here.
Press to play or pause the disc.
Press to open and close the disc tray.
BP68-00342A-00Eng_TV
3/31/04
9:21 AM
Page 7
YOUR NEW TV
Using a Display Deck
You can display a VCR or DVD Player, etc. by using the display deck.
Connection Jacks (Side or Front)
You can connect an A/V component that is used only occasionally, such as a camcorder or
video game. For information on connecting equipment, see page 18.
ΠVIDEO Input
Connect the video signal from a camcorder or video game.
´ AUDIO Inputs
Connect the audio signals from a camcorder or video game.
ˇ S-VIDEO Input
Connect an S-Video signal from a camcorder or video game.
7
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 8
YOUR NEW TV
Connection Jacks (Rear)
Use the rear panel jacks to connect an A/V component that will be connected continuously,
such as a VCR or a DVD player. For more information on connecting equipment, see pages
14~19.
Œ´ˇ¨ˆØ∏”’˝ÔÒÚÆ
ΠAntenna terminals
Two independent cables or antennas can be
connected to these terminals. Use “ANT 1 IN” and
“ANT 2 IN” terminals to receive a signal from VHF/
UHF antennas or your cable system.
Use the“ANT 1 OUT” terminal to send the signal
being received by the “ANT 1 IN” terminal out to
another component (such as a Cable Set-Top Box).
The PIP channel can be received only when a signal
source is connected to “ANT 1 IN”.
´ Surround Speaker Output
Selection
The factory default is set to INT (Internal).
For sound output to external speakers, set to EXT
(External), then sound to the internal speaker is off.
ˇ Surround Speaker Output
Connect to the external speakers.
To improve the sound quality, connect the red wire
to the red terminal and black wire to the black
terminal.
¨ Digital Audio Input jacks
Connect to the digital audio output jacks for device
with digital audio output.
ˆ Audio/Video Output jacks
Connect to the audio/video input jacks of a
recording VCR.
8
Ø Video Input jacks
Connect to the video output jacks of VCRs, DVD
players and similar devices.
∏ Audio Input jacks
Connect to the audio output jacks of VCRs, DVD
players and similar devices.
” S-Video Input jack
Connect to S-VIDEO output jacks of an S-VHS VCR
or DVD player.
’˝ COMPONENT Input jacks
(Y, PB, PR, AUDIO-L/R)
Connect to the audio and video outputs of DVD or
DTV Set-Top Box. 480i/480p/1080i Y,PB and PR
video signal outputs are available.
Ô DVI Audio Input jacks
(Digital Visual Interface)
Connect to the digital audio output jacks for device
with DVI output.
 HDMI/DVI Video Input jack
(High Definition Multimedia Interface)
Connect to the HDMI jack for device with HDMI or
DVI output.
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 9
YOUR NEW TV
Remote Control (TV Funtions)
You can use the remote control up to about 23 feet from the TV. When using the remote
control, always point it directly at the TV. You can also use your remote control to operate your
Set-Top box, VCR, Cable box or DVD player. See pages 67~68 for details.
ΠPOWER
Turns the TV on and off.
´ TV/DVD
Press to switch between TV and
DVD mode.
ˇ Number buttons
Press to select channels directly
on the TV.
¨ +100
Press to select channels over 100.
For example, to select channel 121,
press the “+100,” then press the
“2” and “1.”
ˆ MUTE
Press to temporarily cut off the
sound.
Ø VOL
+, VOL -
Press to increase or decrease the
volume.
∏ FAV. CH (Favorite Channel)
Press to switch between your
favorite channels.
” MENU
Displays the main on-screen menu.
’ ADD/DEL
Press to add or erase channels in
the TV’s memory. Use to memorize
or erase the fine tuning after fine
tuning channels.
˝ A. PROG
Press to store channels in Memory
Automatically
Ô CAPTION
Press to view closed caption
information.
 SELF FOCUS
Press to adjust for the optimum
picture set in the factory.
Ò P.SIZE
Press to change the picture size.
Ú S.MODE
Adjust the TV sound by selecting
one of the preset factory settings
(or select your personal,
customized sound settings.)
Æ MODE
Selects a target device to be
controlled by this remote control
(i.e., TV, STB, VCR, CABLE or DVD).
ı PRE-CH
Tunes to the previous channel.
˜ CH
, CH
Press to change channels.
¯ SOURCE
Each time the button is pressed, all
the inputs connected to the
external component jacks will be
shown in regular sequence.
˘ INFO
Press to display information on the
TV screen.
¿ EXIT
Press to exit the menu.
¸ œ/√/†/…
Control the cursor in the menu.
˛ ENTER
While using the on-screen menus,
press ENTER to activate (or
change) a particular item.
◊ PIP
Activates PIP (Picture-In-Picture).
± CH
, CH
Displays the available channels in
sequence. (These buttons change
channels in the PIP window only.)
≠ SWAP
Press to exchange the video signal
that is currently displayed on the
main screen with the signal in the
PIP window.
– MTS (Multichannel Television
Sound)
Press to choose “Stereo”, “Mono”
or “SAP (Secondary Audio
Program)”.
— STILL (Main picture)
Press to stop the action during a
particular scene. Press again to
resume normal video.
The still function doesn’t operate in
“Component 1” and “Component
2” mode.
9
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 10
YOUR NEW TV
Remote Control (DVD and Extra Funtions)
ΠOPEN/CLOSE
Press to open or close the disc
tray.
´ CLEAR
Press to delete a bookmark
number and cancel the program
play.
” RETURN
Press to return to a previous menu
or exit.
ˇ DVD MENU
Displays the DVD play’s Setup
menu.
¨
Press to search backward through
a disc.
Press to skip the back title,
chapter, or track.
ˆ
Press to stop the disc
Ø ANGLE
Press to access various camera
angles on a DVD.
∏ SET
Used during set up of this remote
control, so that it will work
compatibly with other devices
(VCR, Cable Box, DVD, Set-Top Box
etc.)
10
’
Press to play or pause the disc.
˝
Press to search forward through a
disc.
Press to skip the next title, chapter,
or track.
Ô RESET
If your remote control is not
functioning properly, take out the
batteries and press the RESET
button for about 2~3 seconds. Reinsert the batteries and try using
the remote control again.
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 11
C h a p t e r Tw o
I N S TA L L AT I O N
Connecting VHF and UHF Antennas
Antennas with 300-ohm Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has 300-ohm
twin flat leads, follow the directions below.
1
Place the wires from the twin
leads under the screws on the
300-75 ohm adaptor (not
supplied). Use a screwdriver
to tighten the screws.
2
Plug the adaptor into the “ANT
1 IN” terminal on the rear
panel.
Antennas with 75-ohm Round Leads
Plug the antenna lead into the
“ANT 1 IN” terminal on the
rear panel.
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine
the two antenna signals before connecting the antennas to the TV. This procedure requires an
optional combiner-adaptor (available at most electronics shops).
1
Connect both antenna leads to the combiner.
2
Plug the combiner into the “ANT 1 IN” terminal on the rear
panel.
11
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 12
I N S TA L L AT I O N
Connecting Cable TV
You can connect different cable systems to your TV, including cable without a cable box, and
cable with a cable box that descrambles some or all channels.
Cable without a Cable Box
If you want to connect cable, and you do not need to use a cable box:
Plug the incoming cable into
the “ANT 1 IN” terminal on the
rear panel.
Cable with a Cable box that Descrambles All Channels
1
Find the cable that is
connected to the ANTENNA
OUT terminal on your cable
box.
2
Connect the other end of this
cable to the “ANT 1 IN”
terminal on the rear panel.
12
œ This terminal might be labeled
“ANT OUT”, “VHF OUT”, or
simply “OUT”.
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 13
I N S TA L L AT I O N
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the
instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of
coaxial cable. (These items are available at most electronics stores.)
œ This terminal might be labeled
“ANT IN”, “VHF IN”, or
simply “IN”.
1
Find and disconnect the cable
that is connected to the
ANTENNA IN terminal on your
cable box.
2
Connect this cable to a twoway splitter. Connect a coaxial
cable between an OUTPUT
terminal on the splitter and the
IN terminal on the cable box.
Incoming Cable
Splitter
Cable Box
3
Connect a coaxial cable
between the ANTENNA OUT
terminal on the cable box and
the B-IN terminal on the A/B
switch.
RF (A/B)
Switch
4
Connect another cable
between the other OUT
terminal on the splitter and the
A-IN terminal on the RF (A/B)
switch.
5
Connect the last coaxial cable
between the OUT terminal on
the RF (A/B) switch and the
“ANT 1 IN” terminal on the
rear panel.
After you’ve made this connection, set the A/B switch to the “A” position for normal viewing. Set the A/B
switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B,” you will
need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)
13
BP68-00342A-00Eng_TV
3/31/04
9:22 AM
Page 14
I N S TA L L AT I O N
Connecting a VCR
These instructions assume that you have already connected your TV to an antenna or a cable
TV system (according to the instructions on pages 11~13). Skip step 1 if you have not yet
connected to an antenna or a cable system.
1
Connect a coaxial cable between the “ANT IN” (1 or
2) terminal on the TV and the ANTENNA OUT terminal
on the VCR.
A coaxial cable is usually included with a VCR. (If
not, check your local electronics store).
2
Connect a set of audio cables between the “AV IN 1
(L, R)” (or “AV IN 2 (L, R)”) jacks on the TV and AUDIO
OUT jacks on the VCR.
If you have a mono VCR, connect L(mono) to VCR
audio out using only one audio cable.
3
Connect a video cable between the “AV IN 1 (VIDEO)”
(or “AV IN 2 (VIDEO)”) jack on the TV and the VIDEO
OUT jack on the VCR.
Follow the instructions in “Viewing a VCR or
Camcorder Tape” to view your VCR tape.
• Also, you can connect to “AV 3” on the side panel of TV.
Connecting a Second VCR to Record from the TV
Your TV can send out signals of its picture and sound to be recorded by a second VCR. To do
this, connect your second VCR as follows:
1
Connect a set of audio cables between the “AV OUT
(L, R)” jacks on the TV and the AUDIO IN jacks on the
VCR.
(The VCR input jacks might be either on the front or
rear of the VCR.)
2
Connect a video cable between the “AV OUT (VIDEO)”
jack on the TV and the VIDEO IN jack on the VCR.
Refer to your VCR’s instructions for more information
about how to record using this kind of connection.
14
BP68-00342A-00Eng_TV
3/31/04
9:22 AM
Page 15
I N S TA L L AT I O N
Connecting a DVD Player
The rear panel jacks on your TV make it easy to connect a DVD player to your TV.
Connecting to Y, PB, PR
1
Connect a set of audio cables between the “COMPONENT IN
1 (L, R)” (or “COMPONENT IN 2 (L, R)”) jacks on the TV and
the AUDIO OUT jacks on the DVD player.
2
Connect a set of video cables between the “COMPONENT IN
1 (Y, PB, PR)” (or “COMPONENT IN 2 (Y, PB, PR)”) jacks on the
TV and the VIDEO OUT (Y, PB, PR) jacks on the DVD player.
For an explanation of Component video, see your DVD
player’s owner’s instruction.
Connecting to Regular Audio and Video Jacks
1
Connect a set of audio cables between the “AV
IN 1 (L, R)” (or “AV IN 2 (L, R)”) jacks on the TV
and the AUDIO OUT jacks on the DVD player.
2
Connect a video cable between the “AV IN 1
(VIDEO)” (or “AV IN 2 (VIDEO)”) jack on the TV
and the VIDEO OUT jack on the DVD player.
• Also, you can connect to “AV 3” on the side panel of TV.
15
BP68-00342A-00Eng_TV
3/31/04
9:22 AM
Page 16
I N S TA L L AT I O N
Connecting a Digital TV Set-Top Box
The rear panel jacks on your TV make it easy to connect a Set-Top Box to your TV.
Connecting to Y, PB, PR
1
Connect a coaxial cable to the ANTENNA IN terminal on the
Set-Top Box.
2
Connect a set of audio cables between the “COMPONENT IN
1 (L, R)” (or “COMPONENT IN 2 (L, R)”) jacks on the TV and
the AUDIO OUT jacks on the Set-Top Box.
3
Connect a set of video cables between the “COMPONENT IN
1 (Y, PB, PR)” (or “COMPONENT IN 2 (Y, PB, PR)”) jacks on the
TV and the VIDEO OUT (Y, PB, PR) jacks on the Set-Top Box.
The connections for a typical Set-Top Box are shown. For
detailed information, refer to the Set-Top Box instruction
manual.
16
BP68-00342A-00Eng_TV
3/31/04
9:22 AM
Page 17
I N S TA L L AT I O N
Connecting to DVI (Digital Visual Interface)
By inputting a high-bandwidth digital content protection high-definition picture source to the
DIGITAL INPUT jack on the TV, high-definition pictures can be displayed on the screen in
their digital forms. (This DIGITAL INPUT jack is for use in the future when high-bandwidth
digital content protection DTV decoders, DVD players and D-VHS are put on the market.)
1
Connect a set of audio cables between the “DVI IN
(AUDIO-L, R)” jacks on the TV and the AUDIO OUT
jacks on the Set-Top Box.
2
Connect a video cable between the “HDMI/DVI IN”
jack on the TV and the VIDEO OUT jack on the Set-Top
Box.
• The DIGITAL INPUT jack can only be used with 1080i and 480p picture signals. Set the DTV decoder
DIGITAL OUTPUT jack output setting to 1080i or 480p. The DIGITAL INPUT jack is not compatible
with the picture signal of a PC.
Connecting to HDMI (High Definition Multimedia Interface)
Connect a HDMI cable between the “HDMI/DVI IN”
jacks on the TV and the HDMI OUT jacks on the SetTop Box.
Please check that the HDMI source is powered on.
If not, you can not select “HDMI” in the “Source List”
on-screen menu.
17
BP68-00342A-00Eng_TV
3/31/04
9:22 AM
Page 18
I N S TA L L AT I O N
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV. They allow
you to view the camcorder tapes without using a VCR.
1
Locate the A/V output jacks on the camcorder. They are
usually found on the side or rear of the camcorder.
2
Connect a set of audio cables between the “AV 3 (L, R)”
jacks on the TV and the AUDIO OUT jacks on the camcorder.
If you have mono camcorder, connect L(mono) to
camcorder audio out using only one audio cable.
3
Connect a video cable between the “AV 3 (VIDEO)”
(or “S-VIDEO2 INPUT”) jack on the TV and the VIDEO OUT
jacks on the camcorder.
The audio-video cables shown here are usually included
with a Camcorder. (If not, check your local electronics
store.) If your camcorder is stereo, you need to connect a
set of two cables.
Connecting to the Digital Audio Input
The rear panel jacks on your TV make it easy to connect a device with digital audio output.
After making a connection, set the audio input by reference to page 51.
Connect a audio (or optical) cable between the
“COAXIAL IN” (or “OPTICAL IN”) jack on the TV
and the AUDIO OUT jack on a device with digital
audio output.
18
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 19
I N S TA L L AT I O N
Connecting Additional Speakers
The rear panel jacks on your TV make it easy to take advantage of the surround sound system.
1
Connect speaker audio cables to “SURROUND
SPEAKER OUT” terminals on the TV.
To improve the sound quality, connect the Red wire to
the Red terminal and Black wire to the Black terminal.
2
The factory default of “SURROUND SPEAKER OUT
SELECTION” is set to “INT” (Internal). For sound
output to external speakers, set to “EXT” (External),
then sound to the internal speaker is off.
• The speakers MUST have to a power handling capability of 10 watts minimum (impedance 8 Ω).
Installing Batteries in the Remote Control
1
Slide the back cover all the
way out to open the battery
compartment of the remote
control.
2
Install two AAA size batteries.
3
Replace the cover.
œ Make sure to match the “+”
and “–” ends of the batteries with
the diagram inside the
compartment.
œ Remove the batteries and store
them in a cool, dry place if you
won’t be using the remote control
for a long time. (Assuming typical
TV usage, the batteries last for
about one year.)
• The remote control can be used up to about 23 feet from the TV.
19
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 20
Chapter Three
T V O P E R AT I O N
Turning the TV On and Off
Press the POWER button on the remote control.
You can also use the POWER button on the front panel.
Plug & Play Feature
When the TV is initially powered On, basic customer settings proceed automatically and
subsequently as below.
œ Plug & Play feature doesn’t
work when the V-Chip is
activated or when in the A/V
mode.
1
Press the POWER button on the
remote control.
The “Start Plug & Play” is
displayed.
Press the ENTER button to start.
Plug & Play
Start Plug & Play
OK
Enter
Exit
2
The “Language” menu is
displayed.
Press the … or † button to
select the appropriate language,
then press the ENTER button.
Plug & Play
Language
English
Français
Español
Move
Enter
Skip
3
The “Check antenna input” is
displayed.
Make sure that the antenna is
connected to the TV, then press
the ENTER button.
Plug & Play
Check antenna input.
OK
Enter
4
The “Air/CATV” menu is
displayed.
Press the … or † button to
select the video signal source,
then press the ENTER button.
Plug & Play
Air/CATV
Air
STD
HRC
IRC
Move
20
Skip
Enter
Skip
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 21
T V O P E R AT I O N
œ For details, see page 27.
5
The “Auto Program” menu is
displayed.
Press the ENTER button to start
the auto program.
The TV begins memorizing all of
the available stations.
Plug & Play
Auto Program
Air
6
Stop
Enter
Skip
Plug & Play
Auto Program
75 Channels were memorized.
OK
Enter
Skip
œ For details, see page 52.
6
Plug & Play
When it has finished, the “Clock
Set” menu is displayed.
Set the clock.
Clock Set
Hour
Min
am/pm
--
--
am
Move
Adjust
Enter
Skip
7
When you have finished, press
the ENTER button.
The message “Enjoy your
watching” is displayed.
8
If you want to reset this feature:
Press the MENU button.
Press the … or † button to
select “Setup”, then press the
ENTER button.
Press the … or † button to
select “Plug & Play”, then press
the ENTER button.
The “Plug & Play” is displayed.
Plug & Play
Enjoy your watching.
Exit
TV
Setup
Time
Plug & Play
Language
Self Focus
Blue Screen
Caption
† More
Move
Enter
: English
: On
√
√
√
√
√
√
Return
21
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 22
T V O P E R AT I O N
Viewing the Menus and On-Screen Displays
Viewing the Menus
1
TV
Input
Press the MENU button.
The main menu is displayed.
There are five menu groups:
“Input”, “Picture”, “Sound”,
“Channel” and “Setup”.
Source List
Edit Name
Move
2
Press the … or † button to move
to an item you want in the menu.
Press the œ or √ button to
display, change or use the
selected items.
Press the ENTER button to enter
items in the menu.
Enter
TV
Source List
Edit Name
Move
Enter
Press the EXIT button to exit.
Viewing the Display
Air
11
Mono
CC
Picture
Sound
MTS
Dolby Pro
Clock
22
Exit
Input
3
Press the INFO button on the
remote control.
The TV displays the current
channel, the status of certain
picture and sound settings and
the current time.
√
√
: TV
: Dynamic
: Standard
: Stereo
Logic II : On
: - - : - - am
√
√
: TV
Return
œ You can also use the MENU,
CH / , VOL+/- and
(ENTER) buttons on the
control panel of the TV to make
selections.
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 23
T V O P E R AT I O N
Selecting a Menu Language
1
TV
Setup
Press the MENU button.
Press the … or † button to
select “Setup”, then press the
ENTER button.
Time
Plug & Play
Language
Self Focus
Blue Screen
Caption
† More
Move
2
Enter
TV
Return
Setup
Press the … or † button to
select “Language”, then press
the ENTER button.
Time
Plug & Play
Language
Self Focus
Blue Screen
Caption
† More
Press the … or † button to
select the appropriate language,
then press the ENTER button.
: English
: On
√
√
√
√
√
√
Move
: English
English
Français
: On
Español
Enter
√
√
√
√
√
√
Return
Press the EXIT button to exit.
Selecting the Antenna Input
You can connect two different signal sources by choosing the antenna input (“Ant.1” or
“Ant.2”).
1
TV
Channel
Press the MENU button.
Press the … or † button to
select “Channel”, then press the
ENTER button.
Move
2
√
√
√
√
√
√
Antenna
: Ant.1
Air/CATV
: Air
Auto Program
Favorite Channels
Fine Tune
Add/Delete
† More
Enter
TV
Return
Channel
Press the ENTER button to select
“Antenna”.
Ant.1
Antenna
: Ant.1
Air/CATV
: AirAnt.2
Auto Program
Favorite Channels
Fine Tune
Add/Delete
† More
Press the … or † button to
select “Ant.1”or “Ant.2”, then
press the ENTER button.
Move
Enter
√
√
√
√
√
√
Return
Press the EXIT button to exit.
23
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 24
T V O P E R AT I O N
Adjusting the Screen Automatically (Self Focus)
The “Self Focus” feature automatically finds the optimum picture quality when blurring,
overlapping colors or incorrect focus occurs. These conditions may be caused by moving your
TV.
1
TV
Setup
Press the MENU button.
Press the … or † button to
select “Setup”, then press the
ENTER button.
Time
Plug & Play
Language
Self Focus
Blue Screen
Caption
† More
Move
2
TV
Enter
Return
Self Focus
Press the … or † button to
select “Self Focus”, then press
the ENTER button.
The “Self Focus” is selected.
Press the ENTER button again.
The self focus process begins
with the message “Self Focus”
and horizontal bar is displayed.
When it is finished, all of things
will disappear and the optimum
picture quality can be enjoyed.
: English
: On
√
√
√
√
√
√
√
√
√
Self Focus
Auto
: On
Message Display : On
Move
Enter
œ During the process, minor
distortions of the picture may
occur. At this time, the colors
may diffuse and a searching
pattern will appear on the edges
of the screen. This is a normal
part of the adjustment.
Return
Self Focus
Press the EXIT button to exit.
Alternate method:
Simply press the SELF FOCUS
button on the remote control to
enjoy the optimum picture
quality.
Self Focus
• Changing channels and any other signal changes will pause the self focus until a stable signal has
returned. It resumes after the signal has been stabilised. This feature will not work without a signal
• Ambient light that is too bright may affect the self focus. If this occurs, darken the environment and
try again.
24
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 25
T V O P E R AT I O N
Deactivating the Automatic Execution of the Self Focus
The “Self Focus” feature starts on default. It will automatically begin 10 minutes after switching
on the power and the appearance of the screen image. To set the optimum picture quality, the
“Self Focus” will automatically begin again after another 30 minutes, as the screen image is
then fully stabilised.
1
TV
Setup
Press the MENU button.
Press the … or † button to
select “Setup”, then press the
ENTER button.
Time
Plug & Play
Language
Self Focus
Blue Screen
Caption
† More
Move
2
TV
: English
: On
Enter
Return
Self Focus
Press the … or † button to
select “Self Focus”, then press
the ENTER button.
Self Focus
Auto
: On Off
Message Display : On On
Press the … or † button to
select “Auto”, then press the
ENTER button.
To turn off the automatic
execution of the self focus
feature, select “Off” by pressing
the … or † button, then press
the ENTER button.
√
√
√
√
√
√
Move
Enter
√
√
√
Return
Removing the “Self Focus” Message from the Display
3
Press the … or † button to
select “Message Display”, then
press the ENTER button.
To remove the message “Self
Focus” and horizontal bar on the
screen during the self focus
process, select “Off” by pressing
the … or † button, then press
the ENTER button.
TV
Self Focus
Self Focus
Auto
: On
Message Display : On Off
On
Move
Enter
√
√
√
Return
Press the EXIT button to exit.
25
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 26
T V O P E R AT I O N
Memorizing the Channels
Your TV can memorize and store all of the available channels for both “off-air” (antenna) and
cable channels. After the available channels are memorized, use the CH and CH buttons
to scan through the channels. This eliminates the need to change channels by entering the
channel digits.
Selecting the Video Signal Source
Before your TV can begin memorizing the available channels, you must specify the type of
signal source that is connected to the TV (i.e., an antenna or a cable system).
1
TV
Channel
Press the MENU button.
Press the … or † button to
select “Channel”, then press the
ENTER button.
Move
2
Enter
TV
Return
Channel
Press the … or † button to
select “Air/CATV”, then press the
ENTER button.
Press the … or † button to
select “Air”, “STD”, “HRC” or
“IRC”, then press the ENTER
button.
√
√
√
√
√
√
Antenna
: Ant.1
Air/CATV
: Air
Auto Program
Favorite Channels
Fine Tune
Add/Delete
† More
Antenna
: Ant.1
Air/CATV
: Air Air
STD
Auto Program
HRC
Favorite Channels
IRC
Fine Tune
Add/Delete
† More
Move
Enter
√
√
√
√
√
√
œ If you are connected to an
antenna, press the … or † button
to select “Air”.
œ If you connected cable, press
the … or † button to select the
type of cable system: “STD”,
“HRC” or “IRC”.
Return
Press the EXIT button to exit.
• “STD”, “HRC” and “IRC” identify various types of cable TV systems. Contact your local cable company
to identify the type of cable system that exists in your particular area. At this point the signal source
has been selected. Proceed to “Storing Channels in Memory Automatically”.
• Subscription cable services require service-specific requirement for viewing.
26
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 27
T V O P E R AT I O N
Storing Channels in Memory Automatically
First, select the correct signal source (“Air”, “STD”, “HRC” or “IRC”) as described on the
previous page.
1
TV
Channel
Press the MENU button.
Press the … or † button to
select “Channel”, then press the
ENTER button.
√
√
√
√
√
√
Antenna
: Ant.1
Air/CATV
: Air
Auto Program
Favorite Channels
Fine Tune
Add/Delete
† More
Move
Enter
Return
2
Press the … or † button to
select “Auto Program”, then
press the ENTER button.
Auto Program
Start
Press the ENTER button to start
the auto program.
The TV begins memorizing all of
the available stations.
Press the ENTER button at any
time to interrupt the
memorization process.
Enter
Return
Auto Program
Air
Press the EXIT button to exit.
6
Stop
Enter
Return
27
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 28
T V O P E R AT I O N
Changing Channels
Using the Channel Buttons
Press the CH
or CH
button to change channel.
When you press the CH or CH button, the TV changes channels in sequence. You will
see all the channels that the TV has memorized. (The TV must have memorized at least three
channels.) You will not see channels that were either erased or not memorized.
Using the Number Buttons
Use the number buttons to quickly tune to any channel.
Press the number buttons to go directly to a channel.
For example, to select channel “27”, press the “2”, then “7”. The TV will
change channels when you press the second number.
When you use the number buttons, you can directly select channels that were either erased or
not memorized.
To select a channel over 100, press the +100 button. (For channel “122”, press the +100
button, then “2”, then “2”.)
To change to single-digit channels (0–9) faster, press the “0” before the single digit. (For
channel “4”, press the “0”, then “4”.)
Using the Previous Channel
Press the PRE-CH button.
The TV changes to the last channel
you were watching.
28
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 29
T V O P E R AT I O N
Adding and Erasing Channels
To add channels that were not memorized (or to delete unwanted channels from memory):
1
TV
Channel
Press the MENU button.
Press the … or † button to
select “Channel”, then press the
ENTER button.
√
√
√
√
√
√
Antenna
: Ant.1
Air/CATV
: Air
Auto Program
Favorite Channels
Fine Tune
Add/Delete
† More
Move
Enter
Return
2
Press the … or † button to
select “Add/Delete”, then press
the ENTER button.
Repeatedly pressing the ENTER
button will alternate between
add channel and delete channel.
Press the CH or CH button
to switch to the appropriate
channel, then repeat above.
Add/Delete
Air
6 Not in Memory
Add
Change
Enter
Return
Add/Delete
Air
Press the EXIT button to exit.
6 In Memory
Delete
Change
Enter
Alternate method:
Simply press the ADD/DEL button
on the remote control to add
channels that were not
memorized or to delete
unwanted channels from
memory.
Return
Add/Delete
Air
6 Not in Memory
Add
Change
Enter
Exit
29
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 30
T V O P E R AT I O N
Selecting Your Favorite Channels
You can store your favorite channels for each available input source (such as TV and CATV),
This allows you to quickly and easily find frequently watched channels by pressing the
FAV.CH button on the remote control.
To Store Your Favorite Channels:
1
TV
Channel
Press the MENU button.
Press the … or † button to
select “Channel”, then press the
ENTER button.
Move
2
Enter
TV
Air
Air
Air
Air
Air
Air
Air
Air
Move
Enter
Press the EXIT button to exit.
To View Your Favorite Channels:
Press the FAV.CH button repeatedly
to jump from one favorite channel to
another.
30
Return
Favorite Channels
Press the … or † button to
select “Favorite Channels”, then
press the ENTER button.
Press the … or † button to
select a channel, then press the
ENTER button.
Press the ENTER button again to
deselect the selected channel.
√
√
√
√
√
√
Antenna
: Ant.1
Air/CATV
: Air
Auto Program
Favorite Channels
Fine Tune
Add/Delete
† More
4
6
7
8
9
11
13
14
✔
Return
œ Only memorized channels can
be set as Favorite channels.
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 31
T V O P E R AT I O N
Labeling the Channels
Use this feature to assign an easy-to-remember label to any channel (i.e., “CBS”, “ESPN”,
“PBS2”, CNN1”, etc.) A label consists of five fields, where each field is a letter, a number or a
blank. When the INFO button is pressed, the channel label will appear next to the channel
number.
1
Press the CH
labeled.
or CH
button to tune to the channel that will be
2
TV
Channel
Press the MENU button.
Press the … or † button to
select “Channel”, then press the
ENTER button.
Move
3
Press the … or † button to
select a letter, a number or a
blank. (Results in this sequence:
A...Z, -, 0...9, blank, ✽).
Press the √ button to switch to
the next field, which will be
selected.
Select a second letter or digit
pressing … or † button, as
above. Repeat the process to
select the last two digits.
When you have finished, press
the ENTER button.
Enter
TV
Return
Channel
Press the … or † button to
select “Name”, then press the
ENTER button.
Press the … or † button to
select the channel to be
assigned to a new name, then
press the ENTER button.
√
√
√
√
√
√
Antenna
: Ant.1
Air/CATV
: Air
Auto Program
Favorite Channels
Fine Tune
Add/Delete
† More
… More
Name
Scan
Move
√
√
Enter
TV
œ If you add or delete the TV
channel, the labeled channels list
will also be added or deleted.
Return
Name
Channel
Air
Air
Air
Air
Air
Move
4
6
7
8
9
Adjust
Name
---------A
----
Return
Press the EXIT button to exit.
31
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 32
T V O P E R AT I O N
Scanning the Channels
The TV automatically scan all of the channels it has memorized.
1
TV
Channel
Press the MENU button.
Press the … or † button to
select “Channel”, then press the
ENTER button.
Move
2
Enter
TV
… More
Name
Scan
Move
Scan
Air
Air
√
√
Enter
6
11
: Return
32
Return
Channel
Press the … or † button to
select “Scan”, then press the
ENTER button.
The TV scans all of the channels
memorized.
Press the EXIT button to exit.
√
√
√
√
√
√
Antenna
: Ant.1
Air/CATV
: Air
Auto Program
Favorite Channels
Fine Tune
Add/Delete
† More
Return
œ When the “ANT 2 IN” mode is
selected, the channel scan
function works on the main
picture only.
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 33
T V O P E R AT I O N
Fine Tuning Channels
The Fine Tuning function lets you manually adjust the TV’s tuner if you have difficulty tuning
channels.
1
TV
Channel
Press the MENU button.
Press the … or † button to
select “Channel”, then press the
ENTER button.
Move
Enter
2
Press the … or † button to
select “Fine Tune”, then press
the ENTER button.
√
√
√
√
√
√
Antenna
: Ant.1
Air/CATV
: Air
Auto Program
Favorite Channels
Fine Tune
Add/Delete
† More
Return
Fine Tune
Air
6
0
Reset
Press the œ or √ button to
adjust the fine tuning.
To store the fine tuning setting in
the TV’s memory, press the
ENTER button. The symbol “✽” is
displayed.
To reset the fine tuning to “0”,
select “Reset” by pressing the …
or † button, then press the
ENTER button.
Move
Adjust
Save
Return
Press the EXIT button to exit.
33
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 34
T V O P E R AT I O N
Using Automatic Picture Settings
Your TV has automatic picture settings (“Dynamic”, “Standard” and “Movie”) that are preset at
the factory. You can activate either “Dynamic”, “Standard” or “Movie” by making a selection
from the menu. Or, you can select “Custom” which automatically recalls your personalized
picture settings.
1
TV
Picture
Press the MENU button.
Press the … or † button to
select “Picture”, then press the
ENTER button.
Mode
Custom
Color Tone
Size
Digital NR
PIP
Move
2
: Dynamic
: Normal
: 16:9
: On
Enter
TV
√
√
√
√
√
√
Return
Picture
Press the ENTER button to select
“Mode”.
Mode
Custom
Color Tone
Size
Digital NR
PIP
Press the … or † button to
select a particular item, then
press the ENTER button.
Move
Enter
Dynamic
: Dynamic
Standard
Movie
: Normal
Custom
: 16:9
: On
√
√
√
√
√
√
Return
Press the EXIT button to exit.
• Choose Dynamic for viewing the TV during the day or when there is a bright light in the room.
• Choose Standard for the standard factory settings.
• Choose Movie when viewing a movie.
• Choose Custom if you want to adjust the settings according to personal preference (see next page).
34
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 35
T V O P E R AT I O N
Customizing the Picture
You can use the on-screen menus to change the “Contrast”, “Brightness”, “Sharpness”, “Color”
and “Tint” according to personal preference.
1
TV
Picture
Press the MENU button.
Press the … or † button to
select “Picture”, then press the
ENTER button.
Mode
Custom
Color Tone
Size
Digital NR
PIP
Move
2
: Dynamic
: Normal
: 16:9
: On
Enter
TV
√
√
√
√
√
√
Return
Custom
Press the … or † button to
select “Custom”, then press the
ENTER button.
Contrast
Brightness
Sharpness
Color
Tint
50
Move
Enter
100
45
75
55
50
Return
3
Press the … or † button to
select a particular item, then
press the ENTER button.
Press the œ or √ button to
increase or decrease the value
of a particular item.
Contrast
100
Press the EXIT button to exit.
35
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 36
T V O P E R AT I O N
Selecting the Color Tone
1
TV
Picture
Press the MENU button.
Press the … or † button to
select “Picture”, then press the
ENTER button.
Mode
Custom
Color Tone
Size
Digital NR
PIP
Move
Enter
: Dynamic
: Normal
: 16:9
: On
Return
2
Press the … or † button to
select “Color Tone”, then press
the ENTER button.
Press the œ or √ button to
increase or decrease the value
of the color tone (“Warm 10~1”,
“Normal” and “Cool 1~10”).
Press the EXIT button to exit.
36
Color Tone
Normal
√
√
√
√
√
√
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 37
T V O P E R AT I O N
Changing the Picture Size
1
TV
Picture
Press the MENU button.
Press the … or † button to
select “Picture”, then press the
ENTER button.
Mode
Custom
Color Tone
Size
Digital NR
PIP
Move
2
Return
œ In the “Zoom 1” and “Zoom 2”
modes, lifting is available by
pressing the … or † button.
Size
Press the … or † button to
select “Size”, then press the
ENTER button.
Press the … or † button to
select the screen format you
want.
: Normal
: 16:9
: On
Enter
TV
√
√
√
√
√
√
: Dynamic
16:9
Panorama
Zoom 1
Zoom 2
4:3
Cinema 1
Cinema 2
Move
Enter
œ Captions or subtitles might be
interrupted in the “Cinema1” and
“Cinema2” modes.
Return
Press the EXIT button to exit.
Alternate method:
Press the P.SIZE button on the remote control repeatedly to select one of the screen format you want.
Viewing with a 4:3 signal (When a 4:3 signal is received)
16:9
Panorama
Zoom 1
Cinema 2
Cinema 1
Zoom 2
4:3
Viewing with a 16:9 signal (When a 16:9 signal is received)
The illustrations below show the change of picture while viewing a DVD title.
16:9
Panorama
Zoom 1
Cinema 2
Cinema 1
Zoom 2
4:3
37
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 38
T V O P E R AT I O N
Digital Noise Reduction
If the broadcast signal received by your TV is weak, you can activate this feature to help reduce
any static and ghosting that may appear on the screen.
1
TV
Picture
Press the MENU button.
Press the … or † button to
select “Picture”, then press the
ENTER button.
Mode
Custom
Color Tone
Size
Digital NR
PIP
Move
2
√
√
√
√
√
√
Return
Picture
Mode
Custom
Color Tone
Size
Digital NR
PIP
Move
38
: Normal
: 16:9
: On
Enter
TV
Press the … or † button to
select “Digital NR”, then press
the ENTER button.
Press the … or † button to
select “On” or “Off”, then press
the ENTER button.
Press the EXIT button to exit.
: Dynamic
Enter
: Dynamic
: Normal
: 16:9
: On Off
On
Return
√
√
√
√
√
√
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 39
T V O P E R AT I O N
Viewing Picture-In-Picture
One of the most best features of your TV is the Picture-In-Picture (PIP) feature. The advanced
PIP system allows you to watch two different pictures at once, even if you don’t have a VCR
connected to your TV.
Activating the PIP
1
TV
Picture
Press the MENU button.
Press the … or † button to
select “Picture”, then press the
ENTER button.
Mode
Custom
Color Tone
Size
Digital NR
PIP
Move
2
Alternate method:
Press the PIP button on the
remote control repeatedly to
activate or deactivate the PIP.
Return
PIP
Press the … or † button to
select “PIP”, then press the
ENTER button.
Off
:
: TV On
PIP
Source
Swap
Size
Position
Air/CATV
Channel
Press the ENTER button to select
“PIP”.
Press the … or † button to
select “On”, then press the
ENTER button.
The sub picture appears in the
corner of the screen.
: Normal
: 16:9
: On
Enter
TV
√
√
√
√
√
√
: Dynamic
Move
Air
:
:
: Air
: Air
Enter
√
√
√
√
√
√
6 √
Return
6
Air
11
• This feature doesn’t work when the “V-Chip” or “Caption” is active.
• If you turn the TV off while watching and turn it on again, then the mode will return to normal video.
• The picture size can’t be changed when the “PIP” is active in the TV or AV mode.
39
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 40
T V O P E R AT I O N
Selecting an External Source
3
TV
PIP
Press the … or † button to
select “Source”, then press the
ENTER button.
PIP
Source
Swap
Size
Position
Air/CATV
Channel
If you have not connected any
equipment to the TV’s input
jacks, the signal from these
inputs will not appear.
Move
: On
: TV TV
AV 1
AV 2
:
AV 3
:
S-Video 1
: Air
S-Video 2 6
: Air
Enter
√
√
√
√
√
√
√
Return
œ For more information about
external signals, see page 67).
If you select “TV”, the sub picture
is the same as the main picture.
œ The sub picture doesn’t
support “ANT 2 IN”,
“Component1”, “Component2”,
“Component3” and “HDMI”.
Press the … or † button to
select an external signal, then
press the ENTER button.
Swapping the Sub picture and Main picture
4
TV
PIP
Press the … or † button to
select “Swap”, then press the
ENTER button.
PIP
Source
Swap
Size
Position
Air/CATV
Channel
The sub picture appears in the
main picture, and vice versa.
Move
: On
: TV
:
:
: Air
: Air
Enter
√
√
√
√
√
√
6 √
œ The swapping doesn’t support
“ANT 2 IN”, “Component1”,
“Component2”, “Component3”
and “HDMI”.
œ The swapping doesn’t work in
the “
” (4PIP) and “
”
(13PIP) mode.
Return
Changing the Size of the Sub picture
5
TV
PIP
Press the … or † button to
select “Size”, then press the
ENTER button.
Press the … or † button to
select a size you want, then
press the ENTER button.
40
PIP
Source
Swap
Size
Position
Air/CATV
Channel
Move
: On
: TV
:
:
: Air
: Air
Enter
√
√
√
√
√
√
6 √
Return
œ “
” (Double) function
doesn’t operate in the “HDMI”
mode.
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 41
T V O P E R AT I O N
Changing the Location of the Sub picture
6
TV
PIP
Press the … or † button to
select “Position”, then press the
ENTER button.
PIP
Source
Swap
Size
Position
Air/CATV
Channel
Press the … or † button to
select a position you want, then
press the ENTER button.
Move
√
√
√
√
√
√
6 √
: On
: TV
:
:
: Air
: Air
Enter
Return
Selecting a Signal Source for the Sub picture
If the source of the sub picture is “TV” during PIP on, you can select a signal source of the sub
picture separately from the main picture. (If the main picture is “ANT 2 IN” and the signal
sources are different, making adjustments is necessary.)
7
TV
PIP
Press the … or † button to
select “Air/CATV”, then press the
ENTER button.
Press the … or † button to
select “Air”, “STD”, “HRC” or
“IRC”, then press the ENTER
button.
PIP
Source
Swap
Size
Position
Air/CATV
Channel
Move
: On
: TV
:
:
: AirAir
STD
: Air
HRC
IRC
Enter
√
√
√
√
√
√
6 √
Return
41
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 42
T V O P E R AT I O N
Changing the Channel of the Sub picture
After you set the signal source (antenna or cable) of sub picture, it is easy to change channels.
8
TV
PIP
Press the … or † button to
select “Channel”, then press the
ENTER button.
Press the … or † button to
select a channel you want, then
press the ENTER button.
PIP
Source
Swap
Size
Position
Air/CATV
Channel
Move
: On
: TV
:
:
: Air
: Air
Air
Enter
√
√
√
√
√
√
66 √
œ The channels of sub picture
are not available when antenna is
set to “ANT 2 IN”.
It links to “ANT 1 IN”.
Return
Press the EXIT button to exit.
Alternate method:
Press the CH or CH button to
change channels of sub picture
during PIP on.
Freezing the Picture
Press the STILL button to freeze a
moving picture.
(Normal sound will still be heard.)
Press again to cancel.
42
œ The still function doesn’t
operate in “Component 1, 2”
mode.
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 43
T V O P E R AT I O N
Adjusting the Volume
Press the VOL + or VOL - buttons to increase or decrease the volume.
Using the MUTE Button
At any time, you can temporarily cut off the sound by using the MUTE button.
1
Press the MUTE button on the
remote control.
The message “Mute” is
displayed and the sound cuts off.
2
Mute
To turn mute off press the MUTE
button again or, press either the
VOL- or VOL+ button.
43
BP68-00342A-00Eng_TV
3/30/04
8:51 PM
Page 44
T V O P E R AT I O N
Using Automatic Sound Settings
Your TV has automatic sound settings (“Standard”, “Music”, “Movie” and “Speech”) that are
preset at the factory. You can activate these sound settings by pressing the S.MODE button (or
by making a selection from the menu), or you can select “Custom”, which automatically recalls
your personalized sound settings.
1
TV
Sound
Press the MENU button.
Press the … or † button to
select “Sound”, then press the
ENTER button.
Mode
: Standard
Custom
MTS
: Stereo
Auto Volume
: Off
Dolby Digital
Digital Audio Input
Move
2
Enter
TV
√
√
√
√
√
√
Return
Sound
Press the ENTER button to select
“Mode”.
Standard
Mode
: Standard
Music
Custom
Movie
MTS
: Stereo
Speech
Auto Volume
: Off
Custom
Dolby Digital
Digital Audio Input
Press the … or † button to
select a particular item, then
press the ENTER button.
Move
Enter
√
√
√
√
√
√
Return
Press the EXIT button to exit.
Alternate

advertisement

Related manuals

advertisement