Samsung | HT-X20 | User's Manual | Samsung HT-X20 User's Manual

X20(1~39P) SEA
2007.3.31
2:22 PM
Page 2
Instruction Manual
ENG
DVD HOME
THEATER SYSTEM
HT-X20
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care center.
Samsung Electronics America, Inc.
1-800-SAMSUNG (7267864)
www.samsung.com
AH68-01964R
AH68-01660E
REV: 00
01
COMPACT
DIGITAL AUDIO
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 2
Safety Warnings
CAUTION
Precautions
ENG
Important Safety Instructions
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
This symbol indicates “dangerous voltage”
inside the product that presents a risk of
electric shock or personal injury.
This symbol indicates important instructions
accompanying the product.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1
LASER product.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LASER CLASE 1
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
8) Do not install near any heat sources such as
radiators, heat registers, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding- type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete
outlet.
CAUTION : INVISIBLE LASER RADIATION WHEN OPEN
AND INTERLOCKS DEFEATED, AVOID
EXPOSURE TO BEAM.
Note to CATV system installer
11) Only use attachments/accessories specified by
the manufacturer.
This reminder is provided to call the CATV system
installer’s attention to Section 820~40 of the NEC
which provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall
be connected to the grounding system of the building,
as close to the point of cable entry as practical.
12) Use only with the cart, stand, tripod,
bracket, or table specifi ed by
the manufacturer, or sold with
the apparatus. When a cart is used,
use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
WARNING
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
CAUTION
Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall
be placed on the apparatus.
Ensure that the AC power supply in your house complies with the identification sticker located on the back of your player. Install your
player horizontally, on a suitable base (furniture), with enough space around it for ventilation (3~4inches). Make sure the ventilation slots
are not covered. Do not stack anything on top of the player. Do not place the player on modules or other equipment which may become
hot. Before moving the player, ensure the disc tray is empty. This player is designed for continuous use. Switching off the Home Theater to
the stand-by mode does not disconnect the electrical supply. In order to disconnect the player completely from the power supply, remove
the main plug from the wall outlet, especially when left unused for a long period of time.
7) Do not block any ventilation openings, Install in
accordance with the manufacturer's instructions.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
To reduce the risk of fire or electric shock, do not expose
this appliance to rain or moisture.
2
Read these operating instructions carefully before using the
unit. Follow all the safety instructions listed below. Keep
these operating instructions handy for future
reference.
1) Read these instructions.
PREPARATION
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE REAR COVER (or BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus. Service is also required
if the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
During thunderstorms, disconnect the AC main plug from
the wall outlet.
Voltage peaks due to lightning could damage the unit.
The Mains plug is used as a disconnect device and shall
stay readily operable at any time.
Do not expose the unit to direct sunlight or other heat sources.
This could lead to overheating and malfunction of the unit.
Phones
Protect the player from moisture (i.e. vases) , and excess heat
(e.g.fireplace) or equipment creating strong magnetic or electric fields
(i.e.speakers...). Disconnect the power cable from the AC supply if the
player malfunctions. Your player is not intended for industrial use.
Use of this product is for personal use only.
Condensation may occur if your player or disc has been stored in cold
temperatures.
If transporting the player during the winter, wait approximately 2 hours
until the unit has reached room temperature before using.
The batteries used with this product contain chemicals that are
harmful to the environment.
Do not dispose of batteries in the general household trash.
3
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 4
Features
Contents
PREPARATION
SETUP
The HT-X20 combines the convenience of multi-disc playback capability, including DVD-VIDEO, CD, MP3-CD,
WMA-CD, DivX, CD-R/RW, and DVD R/RW, with a sophisticated FM tuner, all in a single player.
Safety Warnings ............................................................2
Settings........................................................................38
Setting the Language................................................38
Setting TV Screen Type............................................39
Setting Parental Controls (Rating Level) ..................40
Setting the Password................................................40
Setting the Wallpaper ...............................................41
To Select One of the 3 Wallpaper Settings
you've made..............................................................41
DivX (R) Registration ................................................42
Setting the Speaker Mode ........................................42
Setting the Delay Time .............................................43
Setting the Test Tone ................................................44
Setting the Audio.......................................................45
Setting the DRC (Dynamic Range Compression) ....46
Setting the AV SYNC ................................................46
Sound Field (DSP)/EQ Function .................................47
Dolby Pro Logic II Mode ..............................................48
Dolby Pro Logic II Effect..............................................49
Precautions....................................................................3
Features.........................................................................4
USB Host support
Notes on Discs ..............................................................6
You can enjoy media files such as pictures, movies and music saved on an MP3 player, digital camera or USB memory
stick by connecting the storage device to the USB port of the Home Theater.
Description.....................................................................8
Dolby Pro Logic II
Dolby Pro Logic II is a form of multi-channel audio signal decoding technology that improves upon existing
Dolby Pro Logic.
CONNECTIONS
Connecting the Speakers ............................................12
Connecting the Optional Wireless
Receiving Amplifier ......................................................14
DTS (Digital Theater Systems)
Connecting the Video Out to your TV .........................16
DTS is an audio compression format developed by Digital Theater Systems Inc. It delivers full-frequency
5.1 channel sound.
P.SCAN (Progressive Scan) Function .........................17
TV Screen Saver Function
The HT-X20 automatically brightens and darkens your TV screen after 3 minutes in the stop mode.
The HT-X20 will automatically switch to the Power Saving mode after 20 minutes in the Screen Saver mode.
Power Saving Function
The HT-X20 will automatically shut off after 20 minutes in Stop mode.
Customized TV Screen Display
The HT-X20 allows you to select your favorite image during JPEG or DVD playback and set it as your background wallpaper.
Optional Wireless receiver amplifier
Samsung ’s optional rear-channel wireless module does away with cables running between your DVD receiver
and rear-channel speakers. Instead, the rear speakers connect to a compact wireless module that communicates with
your DVD receiver.
4
Connecting Audio from External Components ............18
Connecting the FM Antenna........................................19
PREPARATION
Multi-Disc Playback & FM Tuner
OPERATION
Before Reading the User's Manual .............................20
Before Using Your Home Theater ...............................21
Disc Playback ..............................................................22
MP3/WMA-CD Playback .............................................23
JPEG File Playback.....................................................24
DivX Playback .............................................................25
Using the Playback Function.......................................27
Displaying Disc Information ......................................27
Checking the Remaining Time..................................28
Fast Playback ...........................................................28
Slow Playback ..........................................................28
Skipping Scenes/Songs............................................29
Repeat Playback.......................................................30
To Select a Repeat Playback Mode in the Disc
Information Screen ...................................................30
A-B Repeat Playback................................................31
Step Function............................................................31
Angle Function..........................................................32
Zoom (Screen Enlarge) Function .............................32
EZ VIEW Function ....................................................33
Audio Language Selection Function.........................33
Subtitle Language Selection Function ......................33
Moving Directly to a Scene/Song .............................34
Using the Disc Menu ................................................35
Using the Title Menu.................................................35
Playing Media Files using the USB Host Feature .......36
MISCELLANEOUS
Listening to Radio........................................................50
Convenient Functions..................................................52
Operating a TV with the Remote Control ....................53
Troubleshooting ...........................................................55
Cautions on Handling and Storing Discs.....................57
Language Code List ....................................................58
USB Host Feature Supported Products ......................59
Specifications...............................................................60
5
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 6
Notes on Discs
1
~ 6
ENG
(Your DVD player will only play DVDs that are labeled with identical region codes.)
Mark (Logo)
• Some CD-R discs may not be playable depending on the disc recording device (CD-Recorder or PC) and the condition of
Recorded Signals
Disc Size
Audio + Video
3 1/2"
COMPACT
AUDIO-CD
Audio
DIGITAL AUDIO
Audio + Video
DivX
the disc.
Max. Playing Time
• Use a 650MB/74 minute CD-R disc.
Approx. 240 min. (single-sided)
Approx. 480 min. (double-sided)
Approx. 80 min. (single-sided)
Approx. 160 min. (double-sided)
5"
DVD-VIDEO
Do not use CD-R discs over 700MB/80 minute as they may not be playback.
• Some CD-RW (Rewritable) media, may not be playable.
• Only CD-Rs that are properly "closed" can be fully played. If the session is closed but the disc is left open, you may not
be able to fully play the disc.
5"
74 min.
3 1/2"
20 min.
CD-R MP3 Discs
5"
74 min.
3 1/2"
20 min.
• Only CD-R discs with MP3 files in ISO 9660 or Joliet format can be played.
• MP3 file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
• Use discs recorded with a compression/decompression data rate greater than 128Kbps.
• Only files with the "mp3" and extensions can be played.
• Only a consecutively written multisession disc can be played. If there is a blank segment in the Multisession disc, the
Do not use the following types of disc!
•
•
LD, CD-G, CD-I, CD-ROM and DVD-ROM discs cannot be played on this player.
If such discs are played, a <WRONG DISC FORMAT> message appears on the TV screen.
DVD discs purchased abroad may not play on this player.
If such discs are played, a <CAN'T PLAY THIS DISC PLEASE,CHECK REGION CODE> message appears
on the TV screen.
Copy Protection
player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted
picture from copy-protected DVD discs.
This product incorporates copyright protection technology that is protected by methods claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
This product is covered by one or more of the following U.S. patents:
5,060,220
6,385,587
6,578,163
6,721,493
6,778,755
5,457,669
6,389,570
6,594,208
6,728,474
6,788,629
5,561,649
6,408,408
6,631,110
6,741,535
6,788,630
•
•
•
•
disc can be played only up to the blank segment.
If the disc is not closed, it will take longer to begin playback and not all of the recorded files may be played.
For files encoded in Variable Bit Rate (VBR) format, i.e. files encoded in both low bit rate and high bit rate
(e.g., 32Kbps ~ 320Kbps), the sound may skip during playback.
A maximum of 500 tracks can be played per CD.
A maximum of 300 folders can be played per CD.
CD-R JPEG Discs
• Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD
•
This product does not support Secure (DRM) Media files.
CD-R Discs
Playable Discs
Disc Type
Disc Recording Format
PREPARATION
DVD players and the discs are coded by region. These regional codes must match
in order for the disc to play. If the codes do not match, the disc will not play.
The Region Number for this player is given on the rear panel of the player.
5,705,762
6,466,532
6,658,588
6,744,713
6,795,637
5,987,417
6,473,736
6,674,697
6,744,972
6,810,201
6,043,912
6,477,501
6,674,957
6,765,853
6,862,256
6,222,983
6,480,829
6,687,455
6,765,853
6,868,054
This product is covered by the following U.S. patents:
6,272,096
6,556,520
6,697,307
6,771,890
6,894,963
6,377,524
6,556,521
6,707,985
6,771,891
6,937,552
6,377,531
6,556,522
6,721,243
6,775,465
• Only files with the "jpg" extensions can be played.
• If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played.
• Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played.
• JPEG file names should be 8 characters or less in length and contain no blank spaces or special characters (. / = +).
• Only a consecutively written multisession disc can be played. If there is a blank segment in the multisession disc, the
disc can be played only up to the blank segment.
• A maximum of 9,999 images can be stored on a single CD.
• When playing a Kodak/Fuji Picture CD, only the JPEG files in the picture folder can be played.
• Picture discs other than Kodak/Fuji Picture CDs may take longer to start playing or may not play at all.
DVD R/RW, CD-R/RW DivX Discs
• Since this product only provides encoding formats authorized by DivX Networks, Inc., a DivX file created by the user
might not play.
• Software updates for incompatible formats are not supported.
(Example : QPEL, GMC, resolution higher than 720 x 480 pixels, etc.)
• Sections with a high frame rate might not be played while playing a DivX file.
• For more information about the formats authorized by DivX Networks, Inc., please visit "www.divxnetworks.net".
US4,930,158 US4,930,160
6
7
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 8
Description
ENG
Front Panel
Rear Panel
7
2
8
5. Volume Control
2. Function button
6. USB Connector
3. Stop ( ) button
7. Power (
4. Play/Pause (
) button
5
1
6
10
9
1. Disc Tray
3 4
4
6
1. Video Output Jack
9. Open/Close button
10. Tuning Up & Skip (
) button
Tuning Down & Skip (
) button
) button
5
3
7
4. 5.1 Channel Speaker Output Connectors
Connect the TV's Video Input jack (VIDEO IN) to
the VIDEO OUT jack.
2. Component Video Output Jacks
Connect a TV with component video inputs to these jacks.
8. Standby indicator
2
PREPARATION
1
5. Cooling Fan
6. TX Card Connection (WIRELESS)
7. AUX IN Jack
3. FM 75Ω COAXIAL Jack
Display
Accessories
1
2
13
3
4
14
15
5
6
7
8
9
16
10
11
12
17
18
Remote Control
(AH59-01787S)
8
1. DOLBY DIGITAL indicator
7. TRACK indicator
13. PRO LOGIC indicator
2. P.SCAN indicator
8. PROGRAM indicator
14. MPEG indicator
3. DTS Disc indicator
9. REPEAT indicator
15. DSP indicator
4. LINEAR PCM indicator
10. TUNER indicator
16. System Status Display
5. TITLE indicator
11. STEREO indicator
17. RADIO FREQUENCY indicator
6. CHAPTER indicator
12. RTA indicator
18. SPEAKER indicator
Video Cable
(AH39-40001V)
FM Antenna
(AH42-00017A)
User's Manual
(AH68-01964R)
9
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 10
Description (Con’t)
ENG
Remote Control
18
2
19
3
20
4
5
6
7
21
22
23
1. DVD RECEIVER button
2. TV button
3. POWER button
4. Number (0~9) buttons
5. REMAIN button
6. STEP button
7. Tuning Preset/CD Skip buttons
8. VOLUME button
9. MENU button
10. INFO button
11.
PL II EFFECT button
12.
PL II MODE button
13. TUNER MEMORY, P.SCAN button
14. ZOOM button
15. SLEEP button
16. SLOW, MO/ST button
17. DIMMER button
18.
DVD button
TUNER button
AUX button
8
24
25
9
26
27
10
11
12
28
29
30
31
13
32
14
33
15
10
34
16
35
17
36
1
2
3
Remove the battery cover in the direction of the arrow.
Insert two 1.5V AAA batteries, paying attention to the correct polarities
(+ and –).
Replace the battery cover.
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity : (+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose the batteries to heat or a flame.
PREPARATION
1
Insert Remote Batteries
Operation Range of the Remote Control
The remote control can be used up to approximately 23 feet (7 meters) in a straight line. It can also be operated at a horizontal angle of up to 30° from the remote control sensor.
USB button
19. OPEN/CLOSE button
20. TV/VIDEO button
21. CANCEL button
22. REPEAT button
23.
PLAY/PAUSE button
STOP button
SEARCH buttons
24. TUNING/CH button
25. MUTE button
26. RETURN button
27. Cursor/ENTER button
28. AUDIO button
29. SUBTITLE button
30. DSP/EQ button
31. TEST TONE button
32. SOUND EDIT button
33. DIGEST button
34. LOGO button
35. SLIDE MODE button
36. EZ VIEW button
11
X20(1~39P) SEA
2007.4.6
10:12 AM
Page 12
Connecting the Speakers
ENG
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
HT-X20
Center Speaker
Front Speaker (R)
Front Speaker (L)
Rear Speaker (R)
Rear Speaker (L)
C
SW
L
R
SR
CONNECTIONS
SL
Subwoofer
Position of the Home Theater
• Place it on a stand, cabinet shelf, or under the TV stand.
Front Speakers L R
• Place these speakers in front of your listening position,
•
•
facing inwards (about 45°) toward you.
Place the speakers so that their tweeters will be at the
same height as your ear.
Align the front face of the front speakers with the front face
of the center speaker or place them slightly in front of the
center speakers.
Selecting the Listening Position
The listening position should be located about 2.5 to 3 times
the distance of the TV's screen size away from the TV.
Example : For 32" TVs 2~2.4m (6~8 feet)
For 55" TVs 3.5~4m (11~13 feet)
Rear Speakers SL SR
• Place these speakers behind your listening position.
• If there isn't enough room, place these speakers so they
Back of the Main Unit
Connect the correcting jacks to the back of the DVD player.
• Make sure the colors of the speaker terminals match the colors of the connecting jacks.
face each other.
• Place them about 60 to 90cm (2 to 3feet) above your ear,
facing slightly downward.
Unlike the front and center speakers, the rear speakers
* are
used to handle mainly sound effects and sound will
Center Speaker C
• It is best to install it at the same height as the front speak•
ers.
You can also install it directly over or under the TV.
not come from them all the time.
*
Sound will be heard from the rear speakers in
DVD 5.1-CH or Dolby Pro Logic II mode only.
Subwoofer SW
• The position of the subwoofer is not so critical.
Place it anywhere you like.
12
• Do not let children play with or near the speakers. They could get hurt if a speaker falls.
• Keep the subwoofer speaker out of reach of children so as to prevent children from inserting their hands or alien
substances into the duct (hole) of the subwoofer speaker.
• Do not hang the subwoofer on the wall through the duct (hole).
• If you place a speaker near your TV set, screen color may be distorted because of the magnetic field generated
by the speaker. If this occurs, place the speaker away from your TV set.
13
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 14
Connecting the Optional Wireless Receiving Amplifier
ENG
To connect the rear speakers wirelessly, you have to purchase the wireless receiving module and
TX card from your Samsung retailer.
When you have Purchased the Wireless Receiving Module (SWA-3000)
Front Speaker (R)
Front Speaker (L)
Resetting the Wireless Receiving Module
Reset the system if a communication failure occurs, or if the Link indicator (blue LED) on the wireless receiver does not
light up and the "REAR CHECK" message blinks on the main unit's display.
Reset the system while the main unit and the wireless receiver module (SWA-3000) are in Power Standby mode.
Center Speaker
1
With the main unit turned off, press and hold the remote
control's REMAIN button for 5 seconds.
■
The STANDBY LED on the front panel of the wireless receiver module
2
With the wireless receiver module turned on, use a ball point
pen or a toothpick to press the RESET button on the back of
the unit.
■
The STANDBY LED on the front panel of the wireless receiver module
blinks 2 Times.
Subwoofer
3
Rear Speaker (R)
Rear Speaker (L)
CONNECTIONS
blinks.
Turn on the main unit.
■
The LINK LED of the wireless receiver module is lit and the Reset is
complete.
■
If Power Standby mode continues, repeat Steps 1 to 3 above.
WIRELESS RECEIVER MODULE
1
Connect the Front, Center and Subwoofer speakers to the DVD Player,
refering to page 13.
2
With the DVD Player turned off, insert the TX card into the TX Card
Connection(WIRELESS) on the back of the main unit.
Hold the TX card so that the slanted side faces downward and insert the card into
the port.
The TX card enables communication between the main unit and the wireless receiver.
TX card
Slanted side face down
3
4
Connect the left and right rear speakers to the wireless receiving
module.
Plug the power cord of the wireless receiving module in the wall outlet
and switch the power switch ‘ON’.
• Do not insert a card other than the TX card dedicated for the product.
The product might be damaged or the card may not be removed easily.
• Do not insert the TX card upside down or in the reverse direction.
• Insert the TX card when the DVD Player is turned off. Inserting the card
when it is turned on may cause a problem.
• If the TX Card is inserted, sound is not output from the Rear Speaker
connectors on the main unit.
14
• When the wireless receiving module setting is complete, no sound is output from the Rear Speaker Output
Connectors on the back of the main unit.
• The wireless receiving antenna is built into the wireless receiver module. Keep the unit away from water and
moisture.
• For optimal listening performance, make sure that the area around the wireless receiver module location is clear of
any obstructions.
• Sound will be heard from the wireless rear speakers in DVD 5.1-CH or Dolby Pro Logic II mode
only.
• In 2-CH mode, no sound will be heard from the wireless rear speakers.
• Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is too close
to the main unit, some sound interruption may be heard due to interference.
• If you use a device such as a microwave oven, wireless LAN Card, Bluetooth equipment, or any other device that
uses the same frequency (2.4GHz) near the system, some sound interruption may be heard due to interference.
• The transmission distance of a radio wave is about 33 feet, but may vary depending on your operating environment. If a steel-concrete wall or metallic wall is between the main unit and the wireless receiver module, the system may not operate at all, because the radio wave cannot penetrate metal.
15
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 16
Connecting the Video Out to your TV
Choose one of the two methods for connecting to a TV.
P.SCAN (Progressive Scan) Function
ENG
Unlike regular Interlace Scan, in which two fields of picture information alternate to create the entire picture (odd scan lines,
then even scan lines), Progressive Scan uses one field of information (all lines displayed in one pass) to create a clear and
detailed picture without visible scan lines.
1
Press STOP ( ) button.
If playing a disc, press the STOP ( ) button twice so that “STOP”, appears on the display.
2
Press and hold P.SCAN button on the remote control for over 5 seconds.
Pressing and holding the button for over 5 seconds will select <Progressive Scan> and
<Interlace Scan> alternately.
When you select P.SCAN, "P.SCAN" will appear on the display.
METHOD 1
What is Progressive (or Non-Interlaced) Scanning?
Interlaced Scan (1 FRAME = 2 FIELDS)
Progressive Scan (FULL FRAME)
CONNECTIONS
METHOD 2
(supplied)
To set P.Scan mode for DivX discs, press the P.SCAN button on the remote control for
more than 5 seconds with no disc in the unit (“'NO DISC" on the display), then load the
DivX disc and play.
METHOD 1 : Progressive Scan Component Video ....... (Best Quality)
If your television is equipped with Component Video inputs, connect a Component video cable(not supplied) from
the Component Video Output (Pr, Pb and Y) jacks on the back of the DVD Player to the Component Video Input
jacks on your TV.
METHOD 2 : Composite Video ....... (Good Quality)
Connect the supplied Video cable from the VIDEO OUT jack on the back of the DVD Player to the VIDEO IN jack on
your TV.
In interlaced-scan video, a frame consists of two
interlaced fields (odd and even), where each field contains every other horizontal line in the frame.
The odd field of alternating lines is displayed first, and
then the even field is displayed to fill in the alternating
gaps left by the odd field to form a single frame.
One frame, displayed every 1/30th of a second, contains
two interfaced fields, thus a total of 60 fields are displayed every 1/60th of a second.
The interlaced scanning method is intended for capturing
a still object.
The progressive scanning method scans one full frame of
video consecutively down the screen, line by line.
An entire image is drawn at one time, as opposed to the
interlaced scanning process by which a video image is
drawn in a series of passes.
The progressive scanning method is desirable for dealing
with moving objects.
• When the Progressive scan mode(480p Only) is selected, the VIDEO output (Yellow) does not output
any signal.
• This function works only on TVs equipped with component video inputs (Y, Pr, Pb) that support Progressive
Video. (It does not work on TVs with conventional component inputs, i.e., non-progressive scan TVs.)
• Depending on the capabilities of your TV, this function may not work.
16
17
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 18
Connecting Audio from External Components
Connecting the FM Antenna
ENG
Connecting an External Analog Component
Analog signal components such as a VCR.
FM Antenna (supplied)
CONNECTIONS
Audio Cable
(not supplied)
If the external analog component
has only one Audio Out, connect
either left or right.
1
Connect the AUX IN (Audio) on the Home Theater to the Audio Out of the external analog component.
■
2
Be sure to match connector colors.
1
2
Connect the FM antenna supplied to the FM 75Ω COAXIAL Jack.
Slowly move the antenna wire around until you find a location where reception is good, then fasten it
to a wall or other rigid surface.
Press the AUX button on the remote control to select <AUX> input.
■
You can also use the FUNCTION button on the main unit.
The mode switches as follows : DVD/CD ➝ AUX ➝ USB ➝ FM
• You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of the VCR to
this product.
• This unit does not receive AM broadcasts.
Cooling Fan
The cooling fan supplies cool air to the unit to prevent overheating.
Please observe the following cautions for your safety.
18
■
Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit
may rise and may damage it.
■
Do not obstruct the cooling fan or ventilation holes. If the cooling fan or ventilation holes are covered
with a newspaper or cloth, heat may build up inside the unit and fire may result.
19
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 20
Before Reading the User's Manual
Before Using Your Home Theater
ENG
Make sure to check the following terms before reading the user manual.
Icons that will be used in manual
To Operate your Samsung TV and the Home Theater with the HT-X20's Remote Control
The DVD Home Theater's remote can be used to control Samsung TVs.
Icon
DVD
Term
Definition
DVD
This involves a function available with DVD or
DVD-R/DVD-RW discs that have been recorded and
finalized in Video Mode.
CD
CD
MP3
JPEG
DivX
Plug the main unit's power cord into the AC power supply.
This involves a function available with a data CD
(CD-R or CD-RW).
This involves a function available with CD-R/-RW discs.
JPEG
This involves a function available with CD-R/-RW discs.
2
Press the TV button to set the remote to TV mode.
DivX
This involves a function available with MPEG4 discs.
(DVD R/RW, CD-R or CD-RW)
3
Press the POWER button to turn on your Samsung TV
with this remote.
4
Press the TV/VIDEO button to select VIDEO mode on your TV.
NOTE
This involves a case where a function does not
operate or settings may be cancelled.
This involves tips or instructions on the page that help
each function operate.
• In this manual, the instructions marked with "DVD ( DVD )" are applicable to DVD-VIDEO and
DVD-R/-RW discs that have been recorded in Video Mode and then finalized.
Where a particular DVD type is mentioned, it is indicated separately.
• If a DVD-R/-RW disc has not been recorded properly in DVD Video format, it will not be playable.
VIDEO
5
Press the DVD RECEIVER button to switch to DVD RECEIVER mode to
operate the DVD Home Theater
6
Press the FUNCTION button on the main unit or DVD button
on the remote to enable DVD/CD playback.
OPERATION
MP3
CAUTION
20
1
21
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 22
Disc Playback
DVD
CD
MP3/WMA-CD Playback
ENG
MP3
Data CDs (CD-R, CD-RW) encoded in MP3/WMA format can be played.
1
Press the OPEN/CLOSE button to open the disc tray.
2
Load a disc.
Place the MP3/WMA disc on the disc tray.
■
The MP3/WMA menu screen will appear and playback will start.
The appearance of the menu depends on the MP3/WMA disc.
■
WMA-DRM files cannot be played.
■
■
3
1
Place a disc gently into the tray with the disc’s label facing up.
2
Close the compartment by pressing the OPEN/CLOSE button again.
■
Playback starts automatically.
In Stop mode, use the Cursor , ,
and then press the ENTER button.
■
3
,
button to select the album,
button to select the track.
To change the album, use the Cursor , , , button to select another
album in Stop mode, and then press the ENTER button.
■
4
Use the Cursor
,
To select another album and track, repeat Steps 2 and 3 above.
Press the STOP ( ) button to stop playback.
To stop playback, press the STOP ( ) button during playback.
■
■
OPERATION
• Depending on the recording mode, some MP3/WMA-CDs may not play.
• Table of contents of a MP3-CD varies depending on the MP3/WMA track format
recorded on the disc.
If pressed once, <PRESS PLAY> is displayed and the stop position will be stored in memory.
If the PLAY/PAUSE (
) button or ENTER button is pressed, playback resumes from the stop position.
(This function works only with DVDs.)
If pressed twice, <STOP> is displayed, and if the PLAY/PAUSE (
) button is pressed, playback starts from the
beginning.
To temporarily pause playback, press the PLAY/PAUSE (
■
To resume playback, press the PLAY/PAUSE (
) button during playback.
) button again.
To play a file icon in the screen,
■
• Depending on the content of the disc, the initial screen may appear different.
• Pirated discs will not run in this player because it violates the CSS (Content Scrambling System : a copy protection system) recommendations.
Press the Cursor
,
,
,
button when it is in Stop mode and select a desired icon from the top part of the menu.
Music File Icon : To play music files only, select the
Image File Icon : To view image files only, select the
Icon.
Movie File Icon : To view movie files only, select the
Icon.
All File Icon : To view movie files only, select the
22
Icon.
Icon.
23
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 24
JPEG File Playback
DivX Playback
JPEG
Images captured with a digital camera or camcorder, or JPEG files on a PC can be stored on a CD and then played
back with this Home Theater.
ENG
DivX
The functions on this page apply to DivX disc playback.
Slide Mode
Skip Forward/Back
1
Place the JPEG disc on the disc tray.
■
2
Playback starts automatically. Each image is displayed for 5 seconds and then the next
image is displayed.
Press the SLIDE MODE button.
■
During playback, press the
,
button.
■
Goes to the next file whenever you press the
■
Goes to the previous file whenever you press the
button, if there are over 2 files in the disc.
button, if there are over 2 files in the disc.
Each time the button is pressed, the image makes the transition as follows :
Fast Playback
SLIDE SHOW MODE : 1~11 ➝ SLIDE SHOW MODE : RANDOM ➝
SLIDE SHOW MODE : NONE
Press the
button to skip to the next slide.
Each time the button is pressed, the slide moves backward or forward.
Digest Function
To play back the disc at a faster speed, press the
playback.
■
or
button during
Each time you press either button, the playback speed will change as follows:
2x ➝ 4x ➝ 8x ➝ 32x ➝ Normal.
You can view 9 JPEG images on the TV screen at once.
1
■
JPEG files will be shown in 9 windows.
Press the Cursor , , ,
then press ENTER button.
■
During playback, press the Cursor
button to select the desired image and
button.
■
Playback skips 5 minutes forward whenever you press the Cursor
■
Playback skips 5 minutes back whenever you press the Cursor
The selected image is played for 5 seconds before moving to the next image.
To view the previous or next 9 images, press the
,
button.
OPERATION
2
5 Minute Skip function
Press the DIGEST button during playback.
button.
button.
Zoom Function
1
Press the ZOOM button.
■
Each time you press the button, your selection will toggle between <ZOOM X2> and
<ZOOM OFF>.
2
Rotate/Flip Function
Press the Cursor
,
,
,
Press the Cursor
,
,
,
button to move to the area you want to enlarge.
• A DivX file can be zoomed only in ZOOM X2 mode.
• DivX files have .Avi file extensions, however, not all .Avi files are DivX and may not be
playable in this unit.
button during playback.
button: Flip Vertically
Audio Display
Press the AUDIO button.
button: Rotate 90°
Counterclockwise
button: Rotate 90°
Clockwise
Original Image
■
If there are multiple audio tracks on a disc, you can toggle between them.
■
Each time you press the button, your selection will toggle between <AUDIO (1/N, 2/N ...)> and
•
.
is displayed when there is one supported language in the disc.
button: Flip Horizontally
• The maximum resolutions supported by this product are 5120 x 3480 (or 19.0 MPixel) for
standard JPEG files and 2048 x 1536 (or 3.0 MPixel) for progressive image files.
24
25
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 26
DivX Playback (Con’t)
Using the Playback Function
Subtitle Display
Displaying Disc Information
Press the SUBTITLE button.
■
DVD
CD
MP3
JPEG
DivX
You can view disc playback information on the TV screen.
Each time you press the button, your selection will toggle between <SUBTITLE (1/N, 2/N ...)>
and <SUBTITLE OFF>.
Press the INFO button.
■
If the disc has only one subtitle file, it will be played automatically.
■
■
See number 2 (Caption Function) below for more details concerning Subtitle usage with DivX
discs.
Each time the button is pressed, the display changes as follows:
DVD
If the Disc has more than One Subtitle File
The information
Display disappears
from the screen
If the disc has more than one subtitle file, the default subtitle may not match the
movie and you will have to select your subtitle language as follows:
1
2
ENG
In Stop mode, press the Cursor , button, select the desired subtitle (
from the TV screen, and then press the ENTER button.
)
CD
When you select the desired DivX file from the TV screen, the movie will be
played normally.
DivX(Digital internet video eXpress)
DivX is a video file format developed by Microsoft and is based on MPEG4 compression technology to provide audio and
video data over the Internet in real-time.
MPEG4 is used for video encoding and MP3 for audio encoding so that the users can watch a movie at near DVD-quality
video and audio.
MP3
JPEG
OPERATION
The information
Display disappears
from the screen
DivX
The information
Display disappears
from the screen
1. Supported Formats
This product only supports the following media formats. If both video and audio formats are not supported, the user may
experience problems such as broken images or no sound.
Supported Video Formats
Format
Supported Versions
AVI
DivX3.11~DivX5.1, XviD
• Depending on the disc, the disc information display may appear different.
• Depending on the disc, you can also select DTS, DOLBY DIGITAL, or PRO LOGIC.
WMV
V1/V2/V3/V7
Supported Audio Formats
Format
Bit Rate
Sampling Frequency
MP3
WMA
80~384kbps
56~128kbps
44.1khz
appears on the TV screen!
AC3
128~384kbps
44.1/48khz
DTS
1.5Mbps
44.1khz
• DivX files, including audio and video files, created in the DTS format can only support up to 6Mbps.
If this symbol appears on the TV screen when pressing a button, that operation is not possible with the disc currently being played.
Screen Display
• Aspect Ratio : Although the default DivX resolution is 640x480 pixels (4:3), this product supports up to 720 x 480 pixels
(16:9). TV screen resolutions higher than 800 will not be supported.
• When you play a disc whose sampling frequency is higher than 48khz or 320kbps, you may experience shaking on
the screen during playback.
DVD display
TITLE display
ELAPSED TIME display
STEREO (L/R) display
CD display
CHAPTER display
REPEAT PLAYBACK display
DOLBY DIGITAL display
TRACK (FILE) display
AUDIO LANGUAGE display
2. Caption Function
• You must have some experience with video extraction and editing in order to use this feature properly.
• To use the caption function, save the caption file (*.smi) in the same file name as that of the DivX media file (*.avi)
26
within the same folder.
Example. Root Samsung_007CD1.avi
Samsung_007CD1.smi
• Up to 60 alphanumeric characters or 30 East Asian characters (2 byte characters such as Korean and Chinese) for the
file name.
SUBTITLE display
ANGLE display
27
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 28
Using the Playback Function (Con’t)
Checking the Remaining Time
DVD
CD
Skipping Scenes/Songs
MP3
Press the REMAIN button.
■
Press the
For checking the total and remaining time of a title or chapter being played.
Each time the Remain button is pressed
DVD
ENG
■
■
DVD
,
MP3
button.
Each time the button is pressed during playback, the previous or next chapter, track or
directory (file) will be played.
You cannot skip chapters consecutively.
TITLE ELAPSED ➝ TITLE REMAIN ➝ CHAPTER ELAPSED ➝ CHAPTER REMAIN
DVD
CD
MP3
Fast Playback
DVD
TRACK ELAPSED ➝ TRACK REMAIN ➝ TOTAL ELAPSED ➝ TOTAL REMAIN
CD
MP3
Press the
TITLE 01/05 CHAPTER 004/045
DivX
,
MP3
button.
Each time the button is pressed during playback, the playback speed changes as follows:
2X ➝
4X ➝
8X ➝
32X ➝
PLAY
2X ➝
4X ➝
8X ➝
32X ➝
PLAY
OPERATION
■
TITLE 01/05 CHAPTER 002/045
TRACK REMAIN ➝ TRACK ELAPSED
• During fast playback of a CD or MP3-CD, sound is heard only at 2x speed, and not at 4x,
8x, and 32x speeds.
Slow Playback
DVD
DivX
Press the SLOW button.
■
Each time the button is pressed during playback, the playback speed changes as follows:
DVD
1/2 ➝
1/4 ➝
1/8 ➝
1/2 ➝
1/2 ➝
1/4 ➝
1/8 ➝
PLAY
1/4 ➝
1/8 ➝
PLAY
DivX
• No sound is heard during slow playback.
• Reverse slow playback does not work with DivX.
28
29
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 30
Using the Playback Function (Con’t)
Repeat Playback
DVD
CD
MP3
JPEG
ENG
A-B Repeat Playback
DivX
You can repeatedly play back a designated section of a DVD.
Repeat playback allows you to repeatedly play a chapter, title, track (song), or directory (MP3 file).
1
2
3
Press the REPEAT button.
Each time the button is pressed during playback, the repeat playback mode
changes as follows:
REPEAT : CHAPTER ➝ REPEAT : TITLE ➝ REPEAT : OFF
DVD
4
REPEAT : RANDOM ➝ REPEAT : TRACK ➝ REPEAT : DIR ➝
MP3
JPEG
DivX
Press the INFO button twice.
Press the Cursor
button to move to the REPEAT PLAYBACK (
) display.
Press the Cursor , button to select <A-> and then press the ENTER button at the beginning of the desired segment.
■
REPEAT : TRACK ➝ REPEAT : DISC ➝ REPEAT : OFF
CD
DVD
When the ENTER button is pressed, the selected position will be stored in memory.
Press the ENTER button at the end of the desired segment.
■
The specified segment will be played repeatedly.
REPEAT : DISC ➝ REPEAT : OFF
A-B
CHAPTER : Repeatedly plays the selected chapter.
TRACK : Repeatedly plays the selected track.
TITLE : Repeatedly plays the selected title.
DIR : Repeatedly plays all tracks in the selected folder.
RANDOM : Plays tracks in random order.
(A track that has already been played may be played again.)
DISC : Repeatedly plays the entire disc.
button to select
• The A-B Repeat function does not operate with DivX, MP3 or JPEG discs.
OFF : Cancels Repeat Playback.
To Select a Repeat Playback Mode in the Disc Information Screen
1
2
3
,
DVD
OPERATION
To return to normal playback, press the Cursor
OFF.
Repeat Playback Options
CD
Step Function
Press the INFO button twice.
Press the Cursor
button to move to REPEAT PLAYBACK (
Press the Cursor
button to select the desired Repeat Playback mode.
DVD
DivX
) display.
Press the STEP button.
■
The picture moves forward one frame each time the button is pressed during playback.
To select another album and track, repeat Steps 2 and 3 above.
4
Press the ENTER button.
• No sound is heard during step motion playback.
DVD
CD
• For DivX, MP3 and JPEG discs, you cannot select Repeat Play from the information display screen.
30
31
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 32
Using the Playback Function (Con’t)
Angle Function
EZ VIEW Function
DVD
This function allows you to view the same scene in different angles.
1
2
3
ENG
Press the EZ VIEW button.
Each time the button is pressed, the zoom function will switch between On and Off.
Press the INFO button.
Press the Cursor
button to move to ANGLE (
Press the Cursor
,
■
DVD
When a movie is played in Widescreen format, black bars at the top and bottom of the TV
screen can be removed by pressing the EZ VIEW button.
) display.
button or numeric buttons to select the desired angle.
EZ VIEW
EZ VIEW OFF
Each time the button is pressed, the angle changes as follows:
1/3
2/3
3/3
• This function will not work if the DVD is recorded with multi-camera angle format.
• Black bars may not disappear because some DVD discs have a built-in horizontal to
vertical ratio.
• This feature is not supported for DivX discs.
• During the EZ View operation, some of the left and right sides may be cut slightly.
• The Angle function works only with discs on which multiple angles have been recorded.
Zoom (Screen Enlarge) Function
DVD
DivX
This function allows you to enlarge a particular area of the displayed image.
1
2
3
1
2
Press the ZOOM button.
Press the INFO button twice.
Press the Cursor
language.
■
Press the Cursor
,
,
,
button to move to the area you want to enlarge.
DVD
,
button or numeric buttons to select the desired audio
OPERATION
Audio Language Selection Function
Depending on the number of languages on a DVD disc, a different audio language (ENGLISH,
SPANISH, FRENCH, etc.) is selected each time the button is pressed.
Press the ENTER button.
■
Each time the button is pressed, the zoom level changes as follows:
SP 2/3
FR 3/3
ZOOM X 1.5 ➝ ZOOM X 2 ➝ ZOOM X 3 ➝ ZOOM OFF
SELECT ZOOM POSITION
• When a DivX disc is being played, the screen is enlarged up to twice the normal size.
Subtitle Language Selection Function
1
2
3
DVD
Press the INFO button twice.
Press the Cursor
button to move to SUBTITLE (
Press the Cursor
button or numeric buttons to select the desired subtitle.
EN 1/3
EN 01/ 03
) display.
OFF
SP 02/ 03
FR 03/ 03
OFF / 03
32
• To operate this function, you can also press the AUDIO or SUBTITLE buttons on
the remote control.
• Depending on the disc, the Subtitle and Audio Language functions may not be available.
33
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 34
Using the Playback Function (Con’t)
Moving Directly to a Scene/Song
DVD
1
2
DVD
CD
MP3
ENG
Using the Disc Menu
JPEG
You can use the menus for the audio language, subtitle language, profile, etc.
DVD menu contents differ from disc to disc.
CD
Press the INFO button.
Press the Cursor
,
desired title/track (
button or numeric buttons to select the
1
In Stop mode, press the MENU button.
2
Press the Cursor , button to move to the <Disc Menu> and then
press the ENTER button.
) and then press the ENTER button.
■
3
4
5
6
DVD
Press the Cursor
,
button to move to the Chapter (
) display.
Press the Cursor , button or numeric buttons to select the
desired chapter and then press the ENTER button.
Press the Cursor
,
button to move to time (
3
4
) display.
When you select Disc Menu and it is not supported by the disc, the <This menu is not
supported> message appears on the screen.
Press the Cursor
,
,
,
button to select the desired item.
Press the ENTER button.
Press the MENU button to exit the setup screen.
Press the numeric buttons to select the desired time and then press
the ENTER button.
01/05
0:00:37
• The disc menu display may be different depending on the disc.
1/1
OPERATION
MP3
001/040
JPEG
Press the numeric buttons.
■
The selected file will be played.
■
When playing an MP3 or JPEG disc, you cannot use the Cursor
Using the Title Menu
,
DVD
button to move to a folder.
To move a folder, press the STOP ( ) button and then press the Cursor
,
button.
For DVDs containing multiple titles, you can view the title of each movie. Depending on the disc, the availability of this feature may vary.
1
2
3
In Stop mode, press the MENU button.
Press the Cursor
button to move to the <Title Menu>.
Press the ENTER button.
■
• You can press the
button on the remote control to move directly to the desired
title, chapter, or track.
• Depending on the disc, you may not be able to move to the selected title or time.
,
The title menu appears.
Press the MENU button to exit the setup screen.
• The Title menu display may be different depending on the disc.
34
35
X20(1~39P) SEA
2007.3.31
2:22 PM
Page 36
Playing Media Files using the USB Host Feature
You can enjoy media files such as pictures, movies and music saved on an MP3 player, USB memory stick or digital camera in
high quality video with 5.1 channel Home Theater sound by connecting the storage device to the USB port of the Home Theater.
1
Connect the USB device to the USB port on the front of the unit.
ENG
Compatible Devices
1. USB devices that support USB Mass Storage v1.0. (USB devices that operate as a removable disc
in Windows (2000 or later) without additional driver installation.)
2. MP3 Player: HDD and flash type MP3 players.
3. Digital camera: Cameras that support USB Mass Storage v1.0.
• Cameras that operate as a removable disc in Windows (2000 or later) without additional driver installation.
4. USB HDD and USB Flash Drive: Devices that support USB2.0 or USB1.1.
• You may experience a difference in playback quality when you connect a USB1.1 device.
• For a USB HDD, make sure to connect an auxiliary power cord to the USB HDD for proper operation.
5. USB card Reader: One slot USB card reader and Multi slot USB card reader.
• Depending on the manufacturer. the USB card reader may not be supported.
2
Press the FUNCTION button on the DVD Player or the USB button
on the remote control to select the USB mode.
3
■
<USB> appears on the display screen and then disappears.
■
The USB MENU screen appears on the TV screen and the saved file is played.
• If you install multiple memory devices into a multi card reader, you may experience problems.
6. If you use a USB extension cable, the USB device might not be recognized.
Supported Formats
To stop playback, press the STOP ( ) button.
To prevent damage to the memory stored in the USB device, perform safe removal before
disconnecting the USB cable.
(1) Press the STOP ( ) button twice in a row.
The display will show REMOVE USB.
(2) Remove the USB cable.
Movie
• CBI
• To listen to your music files with 5.1 channel home theater sound, you must set the Dolby
Pro Logic II mode to Matrix. (See page 48)
Skip Forward/Back
During playback, press the
Music
button.
■
When there is more than one file and you press the
button, the next file is selected.
■
When there is more than one file and you press the
button, the previous file is selected.
File
extension
Bit rate
Version
Pixel
Sampling
Frequency
JPG
JPG .JPEG
–
–
640x480
–
MP3
.MP3
80~384kbps
–
–
44.1kHz
WMA
.WMA
56~128kbps
V8
–
44.1kHz
WMV
.WMV
4Mbps
V1,V2,V3,V7
720x480 44.1KHz~48KHz
DivX
.AVI,.ASF
4Mbps
DivX3.11~DivX5.1, XviD
720x480 44.1KHz~48KHz
OPERATION
Still Picture
Safe USB Removal
File name
(Control/Bulk/Interrupt) is not supported.
• Digital
Cameras that use PTP protocol or require additional program installation when connected
to a PC are not supported.
• A device using NTFS file system is not supported. (Only FAT 16/32 (File Allocation Table 16/32) file
system is supported.)
• Some MP3 players, when connected to this product, may not operate depending on the sector size of their
file system.
• The USB host function is not supported if a product that transfers media files by its manufacturerspecific program is connected.
• Does not operate with Janus enabled MTP (Media Transfer Protocol) devices.
• The
USB host function of this product does not support all USB devices. For information on
the supported devices, see page 59.
Fast Playback
To play back the disc at a faster speed, press the
■
button during playback.
Each time you press either button, the playback speed will change as follows:
2x ➝ 4x ➝ 8x ➝ 32x ➝ Normal.
36
37
X20(40~63P) SEA
2007.3.31
2:58 PM
Page 38
Settings
ENG
Setting the Language
Setting TV Screen Type
OSD(On-Screen Display) language is set to English by default.
1
2
3
4
5
Depending on your TV type (Wide Screen or conventional 4:3), you can select the TV's aspect ratio.
Select <LANGUAGE> and then press the ENTER button.
1
2
3
Press the Cursor ,
the ENTER button.
button to select <OSD LANGUAGE> and then press
4
Press the Cursor ,
the ENTER button.
button to select the desired language and then press
In Stop mode, press the MENU button.
Press the Cursor
button to move to <Setup> and then press the ENTER button.
In Stop mode, press the MENU button.
Press the Cursor
button to move to <Setup> and then press the ENTER button.
Press the Cursor button to move to <TV DISPLAY> and then press
the ENTER button.
Press the Cursor ,
the ENTER button.
button to select the desired item and then press
Once the setup is complete, you will be taken to the previous screen.
Once the setup is complete, the OSD will be English if English has been selected as language.
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
Adjusting the TV Aspect Ratio (Screen Size)
• OSD LANGUAGE : Selecting the OSD Language
• AUDIO : Selecting the Audio Language (recorded on the disc)
• SUBTITLE : Selecting the Subtitle Language (recorded on the disc)
• DISC MENU : Selecting the Disc Menu Language (recorded on the disc)
If the language you selected is not recorded on the disc, the menu language will not change even
if you set it to your desired language.
For a standard TV, select either <4:3PS> or <4:3LB> option according to personal preference. Select <WIDE/HDTV> if you have
a widescreen TV.
4:3PS (4:3 Pan&Scan)
Select this to play a 16:9 picture in the pan & scan mode on a conventional TV.
■ You can see the central portion of the screen only (with the sides of the 16:9 picture cut off).
4:3LB (4:3 Letterbox)
Select this to play a 16:9 picture in the letter box mode on a conventional TV.
■ Black bars will appear at the top and bottom of the screen.
SETUP
• OTHERS : To select another language, select OTHERS and enter the language code of your country.
(See page 58 for language codes) AUDIO, SUBTITLE and DISC MENU language can be
selected.
The horizontal to vertical screen size ratio of conventional TVs is 4:3, while that of widescreen and high definition TVs is 16:9. This ratio is
called the aspect ratio. When playing DVDs recorded in different screen sizes, you should adjust the aspect ratio to fit your TV or monitor.
WIDE/HDTV
Select this to view a 16:9 picture in the full-screen mode on your widescreen TV.
■ You can enjoy the widescreen aspect.
• If a DVD is in the 4:3 ratio, you cannot view it in widescreen.
• Since DVD discs are recorded in various image formats, they will look different depending on the software,
the type of TV, and the TV aspect ratio setting.
38
39
X20(40~63P) SEA
2007.3.31
2:58 PM
Page 40
Settings (Con’t)
ENG
Setting Parental Controls (Rating Level)
Use this to restrict playback of adult or violent DVDs you do not want children to view.
1
2
3
4
Setting the Wallpaper
1
During playback, press the PLAY/PAUSE button when an image you like
appears.
2
Press the LOGO button.
button to move to <Setup> and then press the ENTER button.
Press the Cursor button to move to <PARENTAL> and then press
the ENTER button.
Press the Cursor ,
the ENTER button.
<COPY LOGO DATA> will be displayed on the TV screen.
3
button to select the desired rating level and then press
The power will turn off and then back on.
The selected wallpaper will be displayed.
You can select up to 3 wallpaper settings.
COPY LOGO DATA
If you have selected Level 6, you cannot view DVDs with Level 7 or higher.
The higher the level, the closer the content is to violent or adult material.
5
JPEG
While watching a DVD or JPEG CD, you can set the image you like as background wallpaper.
In Stop mode, press the MENU button.
Press the Cursor
DVD
Enter the password and then press the ENTER button.
The password is set to "7890" by default.
Once the setup is complete, you will be taken to the previous screen.
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
To Select One of the 3 Wallpaper Settings you've made
• This function works only if a DVD disc contains the rating level information.
Setting the Password
You can set the password for the Parental (rating level) setting.
4
5
In Stop mode, press the MENU button.
Press the Cursor
Press the ENTER button.
Press the Cursor
button to move to <Setup> and then press the ENTER button.
Press the Cursor
button to move to <LOGO> and then press the ENTER button.
Press the Cursor ,
the ENTER button.
button to select the desired <USER>, and then press
This selects one of the 3 wallpaper screens
button to move to <Setup> and then press the ENTER button.
Press the Cursor button to move to <PASSWORD> and then press
the ENTER button.
In Stop mode, press the MENU button.
5
Press the MENU button to exit the setup screen.
SETUP
1
2
3
1
2
3
4
• ORIGINAL : Select this to set the Samsung Logo image as your wallpaper.
• USER : Select this to set the desired image as your wallpaper.
Enter the password and then press the ENTER button.
Enter the old password, a new password, and confirm new password.
The setting is complete.
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
• The password is set to "7890" by default.
If you have forgotten the rating level password, do the following
• While the player is in No DIsc mode, hold the main unit's STOP (
the display and all settings will return to the default values.
• Press the POWER button.
) button for longer than 5 seconds. “INITIAL” appears on
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
40
41
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 42
Settings (Con’t)
ENG
DivX (R) Registration
Setting the Delay Time
Please use the Registration code to register this player with the DivX (R) video on demand format.
To learn more, go to www.divx.com/vod.
Setting the Speaker Mode
Signal outputs and frequency responses from the speakers will automatically be adjusted according to your speaker
configuration and whether certain speakers are used or not.
1
2
3
4
In Stop mode, press the MENU button.
Press the Cursor
If the speakers cannot be placed at equal distances from the listening position, you can adjust the delay time of the audio
signals from the center and rear speakers.
1
2
3
Press the Cursor , ,
press the ENTER button.
,
button to move to the desired speaker and then
For C, SL, and SR, each time the button is pressed, the mode switches alternately as follows :
SMALL ➝ NONE.
Press the Cursor
button to move to <Audio> and then press the ENTER button.
Press the Cursor button to move to <DELAY TIME> and then press
the ENTER button.
4
Press the Cursor , ,
press the ENTER button.
5
Press the Cursor
button to move to <Audio> and then press the ENTER button.
In the <SPEAKER SETUP>, press the ENTER button again.
In Stop mode, press the MENU button.
,
,
button to move to the desired speaker and then
button to set the Delay time.
You can set the delay time for C between 00 and 05mSEC and for SL and SR between 00 and
15mSEC.
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
For L and R, the mode is set to SMALL.
• SMALL : Select this when using the speakers.
• NONE : Select this when no speaker is connected.
• Depending on PRO LOGIC and STEREO settings, the speaker mode may vary
(see page 48).
Setting up the Speaker Delay Time
When 5.1CH Surround Sound is played, you can enjoy the best sound if the distance between you and each speaker is the same.
Since the sounds arrive at the listening position at different times depending on the placement of speakers, you can adjust this difference by
adding a delay effect to the sound of the Center and Surround Speakers.
Ideal CENTER SPEAKER
placement
Distance between Df and Dc 0 inch 13.6 inches 27.2 inches 40.8 inches 4.5 feet 5.6 feet
Delay Time
0 ms
1 ms
2 ms
3 ms
4 ms
5 ms
SETUP
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
Setting CENTER SPEAKER
If the distance of Dc is equal to or longer than the distance of Df in the figure,
set the mode as 0ms. Otherwise, change the setting according to the table.
Setting REAR (SURROUND) SPEAKERS
If the distance of Df is equal to the distance of Ds in the figure, set the mode
as 0ms. Otherwise, change the setting according to the table.
Ideal
SURROUND
SPEAKER
placement
Distance between Df and Dc 0 inch 40.8 inches 6.7 feet 10.0 feet 13.4 feet 16.7 feet
Delay Time
0 ms
3 ms
6 ms
9 ms
12 ms
15 ms
It is desirable to place all speakers within this circle.
Df: The distance from FRONT SPEAKER
Dc: The distance from CENTER SPEAKER
Ds: The distance from SURROUND SPEAKER
• With
(Dolby Pro Logic II), the delay time may be different for each mode.
• With AC-3 and DTS, the delay time can be set between 00 and 15mSEC.
• The Center channel is only adjustable on 5.1 channel discs.
42
43
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 44
Settings (Con’t)
ENG
Setting the Test Tone
Setting the Audio
Use the Test Tone feature to check the speaker connections.
1
2
3
In Stop mode, press the MENU button.
Press the Cursor
button to move to <Audio> and then press the ENTER button.
Press the Cursor button to move to <TEST TONE> and then press
the ENTER button.
The test tone will be sent to L ➝ C ➝ R ➝ SR ➝ SL ➝ SW in order.
If the ENTER button is pressed again at this time, the test tone will stop.
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
You can adjust the balance and level for each speaker.
1
2
3
4
In Stop mode, press the MENU button.
Press the Cursor
button to move to <Audio> and then press the ENTER button.
Press the Cursor button to move to <SOUND EDIT> and then press
the ENTER button.
Press the Cursor
Press the Cursor
,
,
button to select and adjust the desired item.
button to adjust the settings.
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
Manually Adjusting the Speaker Volume and Balance with the SOUND EDIT Button.
Alternative method: press the TEST TONE button on the remote.
Press the SOUND EDIT button and then press the Cursor
Multi-Channel Pro Logic Mode
button.
Press the TEST TONE button.
■
■
Start
,
Test tone will be produced as follows:
When playing a DVD or CD, this will work only in Stop mode.
Use this function to check that each speaker is correctly connected and that there is
no problem.
L: Front Speaker (L)
R: Front Speaker (R)
C: Center Speaker
SL: Rear Speaker (L)
SETUP
To end the test tone, press the TEST TONE button again.
SW: Subwoofer
SR: Rear Speaker (R)
Adjusting Front/Rear Speaker Balance
• You can select between 00, -6, and OFF.
• The volume decreases as you move closer to –6.
Adjusting Center/Rear/Subwoofer Speaker Level
• The volume level can be adjusted in steps from +6dB to –6dB.
• The sound gets louder as you move closer to +6dB and quieter as you get closer to -6dB.
44
45
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 46
Settings (Con’t)
ENG
Setting the DRC (Dynamic Range Compression)
Sound Field (DSP)/EQ Function
This feature balances the range between the loudest and quietest sounds. You can use this function to enjoy Dolby Digital
sound when watching movies at low volume at night.
1
2
3
4
Press the DSP/EQ button.
In Stop mode, press the MENU button.
Press the Cursor
button to move to <Audio> and then press the ENTER button.
Press the Cursor
button to move to <DRC> and then press the ENTER button.
Press the Cursor
,
When the Cursor
DSP(Digital Signal Processor) : DSP modes have been designed to simulate different acoustic environments.
EQ : You can select ROCK, POP, or CLASSIC to optimize the sound for the genre of music you are playing
<DSP> appears on the display panel.
Each time the button is pressed, the selection changes as follows:
button to adjust the DRC.
button is pressed, the effect is greater, and when the Cursor
button is
pressed, the effect is smaller.
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
Setting the AV SYNC
Video may look slower than the audio if it is connected to a digital TV. If this occurs, adjust the audio delay time to to match
the video.
4
In Stop mode, press the MENU button.
Press the Cursor
button to move to <Audio> and then press the ENTER button.
Press the Cursor button to move to <AV-SYNC> and then press
the ENTER button.
Press the Cursor , button to select the AV-SYNC Delay Time and then
press the ENTER button.
• POP, JAZZ, ROCK : Depending on the genre of music, you can select POP, JAZZ, and ROCK.
• STUDIO : Provides a sense of presence as if in a studio.
• CLUB : Simulates the sound of a dance club with a throbbing bass beat.
• HALL : Provides a clear vocal as if listening in a concert hall.
• MOVIE : Provides the feeling of a movie theater.
• CHURCH : Gives the feel of being in a grand church.
• PASS : Select this for normal listening.
SETUP
1
2
3
You can set the audio delay time between 0 ms and 300 ms. Set it to the optimal status.
Press the RETURN button to return to the previous level.
Press the MENU button to exit the setup screen.
46
• The DSP/EQ function is only available in STEREO mode.
Press the
PL II mode button to show STEREO on the display.
• This feature works with CDs, MP3-CDs, DivX and Dolby Digital discs.
• When playing a DVD disc encoded with two or more channels, multi-channel mode will be
selected automatically and DSP/EQ function does not work.
47
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 48
Settings (Con’t)
ENG
Dolby Pro Logic II Mode
Dolby Pro Logic II Effect
You can select the desired Dolby Pro Logic II audio mode.
Press the
PL II MODE button.
This function works only in Dolby Pro Logic MUSIC mode.
1
Press the
2
Press the
PL II EFFECT button to select <PANORAMA>, then press the Cursor
, button to select the desired effect setting.
PL II MODE button to select <MUSIC> mode.
Each time the button is pressed, the mode changes as follows.
You can select either 0 or 1.
This mode extends the front stereo image to include the surround speakers for an exciting
"wraparound" effect with side wall imaging.
PRO LOGIC II
3
• MUSIC: When listening to music, you can experience sound effects as if you are listening to the
actual performance.
Press the
the Cursor
,
PL II EFFECT button to select <C-WIDTH>, then press
button to select the desired effect setting.
You can select between 0 and 7.
This sets the width of the center image. The higher the setting, the less sound comes from
the center speaker.
• CINEMA : Adds realism to the movie soundtrack.
• PRO LOGIC : You will experience a realistic multi-channel effect, as if using five speakers, while
using just the front left and right speakers.
• MATRIX : You will hear 5.1 channel surround sound.
STEREO : Select this to listen to sound from the front left and right speakers and the subwoofer only.
• When selecting Pro Logic II mode, connect your external device to the AUDIO INPUT jacks
(L and R) on the player. If you connect to only one of the inputs (L or R), you cannot listen to
surround sound.
4
Press the
PL II EFFECT button to select <DIMENS>, then press the Cursor
, button to select the desired setting
You can select between 0 and 6.
Incrementally adjusts the sound field (DSP) from the front or rear.
48
SETUP
• When playing a DVD disc encoded with two or more channels, multi-channel mode will be
selected automatically and the
(Dolby Pro Logic II) button does not work.
49
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 50
Listening to Radio
ENG
Remote Control
1
2
Presetting Stations
Press the TUNER button to select the FM band.
Example : Presetting FM 89.10 in the memory
Tune in to the desired station.
Automatic Tuning 1 : When the
button is pressed, a preset broadcast station is selected.
Automatic Tuning 2 : Press and hold the
broadcasting stations.
Manual Tuning : Briefly press the
,
,
button to automatically search for active
button to increase or decrease the frequency incrementally.
1
2
Press the
3
Press the TUNER MEMORY button.
Main Unit
1
2
Press the TUNER button to select the FM band.
,
button to select <89.10>.
<PRGM> flashes in the display.
Press the FUNCTION button to select the FM band.
Select a broadcast station.
4
5
Manual Tuning : Press the STOP ( ) button to select <MANUAL> and then briefly press
the
button to tune in to a lower or higher frequency.
Press the MO/ST button to listen in Mono/Stereo.
Each time the button is pressed, the sound switches between <STEREO> and <MONO>.
In a poor reception area, select MONO for a clear, interference-free broadcast.
button to select preset number.
You can select between 1 and 15 presets.
Automatic Tuning 1 : Press the STOP ( ) button to select <PRESET> and then press
the
button to select the preset station.
Automatic Tuning 2 : Press the STOP ( ) button to select <MANUAL> and then press and
hold the
button to automatically search the band.
Press the
Press the TUNER MEMORY button again.
Press the TUNER MEMORY button before <PRGM> disappears from the display.
<PRGM> disappears from the display and the station is stored in memory.
6
To preset another station, repeat steps 2 to 5.
To tune in to a preset station, press the
trol to select a channel.
button on the remote con-
• This unit does not receive AM broadcasts.
MISCELLANEOUS
50
51
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 52
Convenient Functions
Operating a TV with the Remote Control
Sleep Timer Function
When Operating a TV with the Remote Control
You can set the time that the Home Theater will shut itself off.
Press the SLEEP button.
<SLEEP> will be displayed. Each time the button is pressed, the preset time changes as follows :
10 ➝ 20➝ 30➝ 60➝ 90➝ 120➝ 150➝ OFF.
1
2
3
The remaining time before the Home Theater will shut itself off is displayed.
Pressing the button again changes the sleep time from what you have set earlier.
Adjusting Display Brightness
Press the TV button to set the remote to TV mode.
Press the POWER button to turn on the TV.
While holding down POWER, enter the code corresponding
to your brand of TV.
If there is more than one code listed for your TV in the table, enter one at a time to determine which code works.
To confirm the sleep timer setting, press the SLEEP button.
To cancel the sleep timer, press the SLEEP button until <OFF> appears on
the display.
ENG
Example: For a Samsung TV
While holding down POWER, use the number buttons to enter 00, 15, 16, 17 and 40.
4
If the TV turns off, the setting is complete.
You can use the TV POWER, VOLUME, CHANNEL, and Numeric buttons (0~9).
• The Remote control may not work on some brands of TVs. Also, some operations may
not be possible depending on your brand of TV.
• If you do not set the remote control with the code for your brand of TV, the remote control
will work on a Samsung TV by default.
You can adjust the brightness of the display on the main unit so it won't interfere with your movie viewing.
Press the DIMMER button.
Each time the button is pressed, the brightness of front display will be adjusted.
Mute Function
This is useful when answering a doorbell or telephone call.
<MUTE> appears in the display.
To restore the sound, press the MUTE button again.
52
MISCELLANEOUS
Press the MUTE button.
53
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 54
Operating a TV with the Remote Control (Con’t)
ENG
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off the unit, disconnect the power cord, and contact the nearest authorized
dealer or Samsung Electronics Service Center.
TV Brand Code List
No.
Brand
Code
No.
Brand
Code
1
Admiral (M.Wards)
56, 57, 58
44
MTC
18
2
A Mark
01, 15
45
NEC
18, 19, 20, 40, 59, 60
3
Anam
01, 02, 03, 04, 05, 06, 07, 08, 09, 10, 11, 12,
46
Nikei
03
13, 14
47
Onking
03
4
AOC
01, 18, 40, 48
48
Onwa
03
5
Bell & Howell (M.Wards)
57, 58, 81
49
Panasonic
06, 07, 08, 09, 54, 66, 67, 73, 74
6
Brocsonic
59, 60
50
Penney
18
7
Candle
18
51
Philco
03, 15, 17, 18, 48, 54, 59, 62, 69, 90
8
Cetronic
03
52
Philips
15, 17, 18, 40, 48, 54, 62, 72
9
Citizen
03, 18, 25
53
Pioneer
63, 66, 80, 91
10
Cinema
97
54
Portland
15, 18, 59
11
Classic
03
55
Proton
40
12
Concerto
18
56
Quasar
06, 66, 67
13
Contec
46
57
Radio Shack
17, 48, 56, 60, 61, 75
14
Coronado
15
58
RCA/Proscan
18, 59, 67, 76, 77, 78, 92, 93, 94
15
Craig
03, 05, 61, 82, 83, 84
59
Realistic
03, 19
16
Croslex
62
60
Sampo
40
17
Crown
03
61
Samsung
00, 15, 16, 17, 40, 43, 46, 47, 48, 49, 59, 60,
18
Curtis Mates
59, 61, 63
19
CXC
03
62
20
Daewoo
02, 03, 04, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24,
25, 26, 27, 28, 29, 30, 32, 34, 35, 36, 48, 59, 90
Sanyo
19, 61, 65
63
Scott
03, 40, 60, 61
64
Sears
15, 18, 19
15, 57, 64
Daytron
40
65
Sharp
22
Dynasty
03
66
Signature 2000 (M.Wards)
57, 58
23
Emerson
03, 15, 40, 46, 59, 61, 64, 82, 83, 84, 85
67
Sony
50, 51, 52, 53, 55
24
Fisher
19, 65
68
Soundesign
03, 40
25
Funai
03
69
Spectricon
01
26
Futuretech
03
70
SSS
18
27
General Electric (GE)
06, 40, 56, 59, 66, 67, 68
71
Sylvania
18, 40, 48, 54, 59, 60, 62
28
Hall Mark
40
72
Symphonic
61, 95, 96
29
Hitachi
15, 18, 50, 59, 69
73
Tatung
06
30
Inkel
45
74
Techwood
18
31
JC Penny
56, 59, 67, 86
75
Teknika
03, 15, 18, 25
32
JVC
70
76
TMK
18, 40
33
KTV
59, 61, 87, 88
77
Toshiba
19, 57, 63, 71
34
KEC
03, 15, 40
78
Vidtech
18
35
KMC
15
79
Videch
59, 60, 69
36
LG (Goldstar)
01, 15, 16, 17, 37, 38, 39, 40, 41, 42, 43, 44
80
Wards
15, 17, 18, 40, 48, 54, 60, 64
37
38
Luxman
18
81
Yamaha
18
LXI (Sears)
19, 54, 56, 59, 60, 62, 63, 65, 71
82
York
40
39
Magnavox
15, 17, 18, 48, 54, 59, 60, 62, 72, 89
83
Yupiteru
03
40
Marantz
40, 54
84
Zenith
58, 79
41
Matsui
54
85
Zonda
01
86
Dongyang
03, 54
MGA
18, 40
43
Mitsubishi/MGA
18, 40, 59, 60, 75
Disc tray does not open.
Check/Remedy
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
• Check the region number of the DVD.
DVD discs purchased from abroad may not be playable.
Playback does not start.
• CD-ROMs and DVD-ROMs cannot be played on this DVD
player.
• Make sure that the rating level is correct.
Playback does not start
immediately when the
Play/Pause button is pressed.
• Are you using a deformed disc or a disc with scratches on
the surface?
• Wipe the disc clean.
• No sound is heard during fast playback, slow playback, and step
98
21
42
Symptom
motion playback.
Sound is not produced.
• Are the speakers connected properly? Is the speaker setup correctly customized?
• Is the disc severely damaged?
• When listening to a CD or radio, sound is output to the front
Sound can be heard only from a
few speakers and not all six.
•
•
speakers (L/R) only. Select "PRO LOGIC II" by pressing
PL II
(Dolby Pro Logic II) on the remote control to use all six speakers.
Make sure that the DVD disc is 5.1-CH compatible.
If you set C, SL, and SR to NONE in the speaker mode in the
audio setup of the setup screen, no sound is heard from the
center speaker and the front left and right speakers. Set C, SL,
and SR to SMALL.
• Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital
Dolby Digital 5.1 CH Surround
Sound is not produced.
•
5.1 CH Surround Sound is produced only if the disc is recorded
with 5.1 channel sound.
Is the audio language correctly set to DOLBY DIGITAL 5.1-CH in
the information display?
• Is the remote control being operated within its operation range of
The remote control does not
work.
•
•
MISCELLANEOUS
54
Troubleshooting
angle and distance?
Are the batteries exhausted?
Have you selected the mode(TV/DVD) functions of the remote
control (TV or DVD) correctly?
55
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 56
Troubleshooting (Con’t)
Cautions on Handling and Storing Discs
ENG
Small scratches on the disc may reduce sound and picture quality or cause skipping.
Be especially careful not to scratch discs when handling them.
Symptom
• Disc is rotating but no
picture is produced.
• Picture quality is poor and
picture is shaking.
Check/Remedy
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not get on
the surface.
Do not stick paper or tape on the disc.
• Is the TV power on?
• Are the video cables connected properly?
• Is the disc dirty or damaged?
• A poorly manufactured disc may not be playable.
Audio language and subtitles
do not work.
• Audio language and subtitles will not work if the disc does not con-
Menu screen does not appear
even when the menu function is
selected.
• Are you using a disc that does not contain menus?
tain them.
Disc Storage
Do not keep in
direct sunlight
Keep in a cool
ventilated area
Keep in a clean
Protection jacket.
Store vertically.
• You can play 16:9 DVDs in 16:9 WIDE mode, 4:3 LETTER BOX
mode, or 4:3 PAN SCAN mode, but 4:3 DVDs can be seen in 4:3
ratio only. Refer to the DVD disc jacket and then select the appropriate function.
Aspect ratio cannot be changed.
• The main unit is not working.
(Example: The power goes out
or strange noise is heard.)
• The DVD player is not working
normally.
• Turn off the power and hold the STOP(
) button on the main unit
for longer than 5 seconds.
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• While “NO DISC” message appears on the display of main unit, hold
The password for rating level
has been forgotten.
•
the main unit's STOP( ) button for longer than 5 seconds. “INITIAL”
appears on the display and all settings will return to the default values.
Press the POWER button.
Can't receive radio broadcast.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an area with good reception.
56
Handling and Storing Discs
When you get fingerprints or dirt on the disc, clean it with a mild
detergent diluted in water and wipe with a soft cloth.
• When cleaning, wipe gently from the inside to the outside of the
disc.
• Condensation may form if warm air comes into contact with cold parts inside
the player. When condensation forms inside the player, the player may not
operate correctly. If this occurs, remove the disc and let the player stand for
1 or 2 hours with the power on.
MISCELLANEOUS
Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• Do not allow the discs to become contaminated with dirt.
• Do not load cracked or scratched discs.
57
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 58
Language Code List
USB Host Feature Supported Products
ENG
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu” (See page 38).
Digital Camera
Code
Code
Language
Code
Language
Code
Language
1027
Afar
1181
Frisian
1334
Latvian, Lettish
1506
Slovenian
1028
Abkhazian
1183
Irish
1345
Malagasy
1507
Samoan
1032
Afrikaans
1186
Scots Gaelic
1347
Maori
1508
Shona
1039
Amharic
1194
Galician
1349
Macedonian
1509
Somali
1044
Arabic
1196
Guarani
1350
Malayalam
1511
Albanian
1045
Assamese
1203
Gujarati
1352
Mongolian
1512
Serbian
1051
Aymara
1209
Hausa
1353
Moldavian
1513
Siswati
1052
Azerbaijani
1217
Hindi
1356
Marathi
1514
Sesotho
1053
Bashkir
1226
Croatian
1357
Malay
1515
Sundanese
1057
Byelorussian
1229
Hungarian
1358
Maltese
1516
Swedish
1059
Bulgarian
1233
Armenian
1363
Burmese
1517
Swahili
1060
Bihari
1235
Interlingua
1365
Nauru
1521
Tamil
1069
Bislama
1239
Interlingue
1369
Nepali
1525
Tegulu
1066
Bengali; Bangla
1245
Inupiak
1376
Dutch
1527
Tajik
1067
Tibetan
1248
Indonesian
1379
Norwegian
1528
Thai
1070
Breton
1253
Icelandic
1393
Occitan
1529
Tigrinya
1079
Catalan
1254
Italian
1403
(Afan) Oromo
1531
Turkmen
1093
Corsican
1257
Hebrew
1408
Oriya
1532
Tagalog
1097
Czech
1261
Japanese
1417
Punjabi
1534
Setswana
1103
Welsh
1269
Yiddish
1428
Polish
1535
Tonga
1105
Danish
1283
Javanese
1435
Pashto, Pushto
1538
Turkish
1109
German
1287
Georgian
1436
Portuguese
1539
Tsonga
1130
Bhutani
1297
Kazakh
1463
Quechua
1540
Tatar
1142
Greek
1298
Greenlandic
1481
Rhaeto-Romance
1543
Twi
1144
English
1299
Cambodian
1482
Kirundi
1557
Ukrainian
1145
Esperanto
1300
Kannada
1483
Romanian
1564
Urdu
1149
Spanish
1301
Korean
1489
Russian
1572
Uzbek
1150
Estonian
1305
Kashmiri
1491
Kinyarwanda
1581
Vietnamese
1151
Basque
1307
Kurdish
1495
Sanskrit
1587
Volapuk
1157
Persian
1311
Kirghiz
1498
Sindhi
1613
Wolof
1165
Finnish
1313
Latin
1501
Sangro
1632
Xhosa
1166
Fiji
1326
Lingala
1502
Serbo-Croatian
1665
Yoruba
1171
Faeroese
1327
Laothian
1503
Singhalese
1684
Chinese
1174
French
1332
Lithuanian
1505
Slovak
1697
Zulu
Product
Finepix-A340
Finepix-F810
Finepix-F610
Finepix-f450
Finepix S7000
Finepix A310
KD-310Z
Finecam SL300R
Finecam SL400R
Finecam S5R
Finecam Xt
Dimage-Z1
Dimage Z1
Dimage X21
Coolpix4200
Coolpix4300
Coolpix 2200
Coolpix 3500
Coolpix 3700
Coolpix 4100
Coolpix 5200
Stylus 410 digital
300-digital
U300
X-350
C-760
C-5060
X1
U-mini
Lumix-FZ20
DMC-FX7GD
Lumix LC33
LUMIX DMC-F1
Optio-S40
Optio-S50
Optio 33LF
Optio MX
Digimax-420
Digimax-400
Sora PDR-T30
Coolpix 5900
Coolpix S1
Coolpix 7600
DMC-FX7
Dimage Xt
AZ-1
Company
Type
Fuji
Fuji
Fuji
Fuji
Fuji
Fuji
Konica
Kyocera
Kyocera
Kyocera
Kyocera
Minolta
Minolta
Minolta
Nikon
Nikon
Nikon
Nikon
Nikon
Nikon
Nikon
Olympus
Olympus
Olympus
Olympus
Olympus
Olympus
Olympus
Olympus
Panasonic
Panasonic
Panasonic
Panasonic
Pentax
Pentax
Pentax
Pentax
Samsung
Samsung
Toshiba
Nikon
Nikon
Nikon
Panasonic
Minolta
Olympus
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Digital Camera
Product
Cruzer Micro
Cruzer Mini
Cruzer Mini
SONY Micro Vault
FLEX DRIVE
AnyDrive
XTICK
Micro Mini
iFlash
LG
RiDATA
Company
Type
Sandisk
Sandisk
Sandisk
Sony
Serotech
A.L tech
LG
Iomega
Imation
XTICK(M)
EZDrive
USB 2.0 USB Flash Drive 128M
USB 2.0 128M
USB 2.0 256M
USB 2.0 64MB
USB 2.0 32MB
USB 2.0 128MB
USB 2.0 128M
USB 2.0 128M
USB 2.0 64M
USB 2.0 64M
USB 2.0 64M
MP3 Player
Product
Company
Type
Creative MuVo NX128M
Iriver H320
YH-920
YP-T7
YP-MT6
YP-T6
YP-53
YP-ST5
YP-T5
YP-60
YP-780
YP-35
YP-55
iAUDIO U2
iAUDIO G3
iAudio M3
SI-M500L
H10
YP-T5 VB
YP-53
Creative
Iriver
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Samsung
Cowon
Cowon
Cowon
Sharp
Iriver
Samsung
Samsung
128 MB MP3 Player
20G HDD MP3 Player
20G HDD MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
MP3 Player
HDD MP3 Player
256MB MP3 Player
MP3 Player
MP3 Player
256MB MP3 Player
USB External HDD
Product
MOMOBAY UX-2
Company
Type
Dvico
USB 2.0
MISCELLANEOUS
58
Language
USB Flash Disc
59
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 60
Specifications
Power Requirements
Power Consumption
Weight
GENERAL
Dimensions (W x H x D)
Operating Temperature Range
Operating Humidity Range
Usable Sensitivity
FM
S/N Ratio
TUNER
Distortion
Composite Video
VIDEO
OUTPUT Component Video
Front speaker output
Center speaker output
Rear speaker output
Subwoofer speaker output
AMPLIFIER
Frequency range
S/N Ratio
Channel separation
Input sensitivity
Speaker system
Impedance
Frequency range
Output sound pressure level
SPEAKER Rated input
Maximum input
Dimensions (W x H x D)
Weights
Warranty
AC 120V ~ 60Hz
60W
7.3 Ibs
17 x 2.6 x 13.8 inches
41°F ~ 95°F
10% ~ 75%
10dB
60dB
0.5%
1.0Vp-p(75Ω load)
Y:1.0Vp-p(75Ω load)
Pr:0.70Vp-p(75Ω load)
Pb:0.70Vp-p(75Ω load)
100W x 2(3Ω)
100W(3Ω)
100W x 2(3Ω)
100W(3Ω)
20Hz~20KHz
75dB
60dB
(AUX)400mV
5.1ch speaker system
Subwoofer speaker
Front/Center/Rear speaker
3Ω
3Ω x 5
35Hz~155KHz
140Hz~20KHz
86dB/W/M
86dB/W/M
100W
100W
200W
200W
Front/Rear
Center
Front/Rear
Center
3.5 in. x 6.6 in. x 3.7 in. 7.1 in. x 12.6 in. x 15.4 in.
9.8 in. x 3.5 in. x 3.7 in.
1.3Ibs/1.1Ibs
10.1 Ibs
1.5Ibs
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered new, in the original
carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited
warranty period of:
One (1) Year Parts and Labor*
(*90 Days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. To receive
warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty service can only be
performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to
SAMSUNG or SAMSUNG's authorized service center. Transportation of the product to and from the service center is the responsibility of the
purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if
found to be defective during the limited warranty period specified above. All replaced parts and products become the property of SAMSUNG and
must be returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is
longer.
SAMSUNG’s obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set forth in the
applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an “AS IS” basis. Non-SAMSUNG
manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent otherwise
expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including, but not limited to:
damage which occurs in shipment; delivery and installation; applications and uses for which this product was not intended; altered product or
serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products,
equipment, systems, utilities, services, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied
and authorized by SAMSUNG, or which damage this product or result in service problems; incorrect electrical line voltage, fluctuations and
surges; customer adjustments and failure to follow operating instructions, cleaning, maintenance and environmental instructions that are covered
and prescribed in the instruction book; product removal or reinstallation; reception problems and distortion related to noise, echo, interference or
other signal transmission and delivery problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS
WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING
ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER
BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO
USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN
AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT
LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
PURCHASER’S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS
PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT
EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR
EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages,
so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG at:
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ 07660-0511
1-800-SAMSUNG (726-7864) and www.samsung.com
60
X20(40~63P) SEA
2007.3.31
2:59 PM
Page 62
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Region
Country
Customer Care Center
Web Site
Download PDF

advertising