Samsung HW-D7000 User's Manual

Samsung HW-D7000 User's Manual
HW-D7000
Blu-ray™
AV Receiver System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
HW-D7000_XAA_0321.indd 1
2011-03-21
2:00:15
Safety Information
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lighting flash and Arrowhead within
Triangle Is awarning sign alerting you of
dangerous voltage Inside the product.
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The explanation point within the triangle is
a warning sign alerting you of important
instructions accompanying the product.
WARNING
CAUTION
• To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
• Apparatus shall not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed on
the apparatus.
• The Mains plug is used as a disconnect device and shall stay
readily operable at any time.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1
PRODUCTO
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
CLASS 1 LASER PRODUCT
• This product is classified as a CLASS 1 LASER
product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
• Complies with 21CFR 1040.10 except for deviations
pursuant to Laser Notice No. 50, dated June 24, 2007.
DANGER
VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN.
AVOID DIRECT EXPOSURE TO BEAM. (FDA 21 CFR)
CAUTION
• CLASS 3B VISIBLE AND INVISIBLE LASER RADIATION
WHEN OPEN. AVOID EXPOSURE TO THE BEAM (IEC
60825-1)
• THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS
OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN
COVER AND DO NOT REPAIR YOURSELF. REFER
SERVICING TO QUALIFIED PERSONNEL.
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use shielded
cables and connectors for connections.
FCC NOTE (for U.S.A)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION : FCC regulations state that any unauthorized changes or modifications to this equipment may void the user’s
authority to operate it.
2
English
HW-D7000_XAA_0321.indd 2
2011-03-21
2:00:47
Important Safety Instructions
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed
below. Keep these operating instructions handy for future reference.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11) Only use attachment/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
English
HW-D7000_XAA_0321.indd 3
3
2011-03-21
2:00:48
Safety Information
Precautions
• Ensure that the AC power supply in your house complies with specifications listed on the identification sticker
located on the back of your product.
• Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation
(7.5~10cm / 20~25 inches).
• Do not place the product on amplifiers or other equipment which may become hot.
Make sure the ventilation slots are not covered.
• Do not stack anything on top of the product.
• Before moving the product, ensure the Disc Insert Hole is empty.
• To disconnect the product completely from the power supply, remove its plug from the wall outlet.
- If you leave the product unused for a long period of time, disconnect the plug from the wall outlet.
• During thunderstorms, disconnect the AC plug from the wall outlet. Voltage spikes caused by lightning could
damage the product.
• Do not expose the product to direct sunlight or other heat sources. This could cause the product to overheat
and malfunction.
• Protect the product from moisture, excess heat, and equipment creating strong magnetic or electric fields (i.e.
speakers.).
• Disconnect the power cable from the AC supply if the product malfunctions.
• Your product is not intended for industrial use. It is for personal use only.
• Condensation may occur if you store your product or a disc in cold temperatures. If transporting the product
during the winter, wait approximately 2 hours until the product has reached room temperature before using.
• The batteries used with this product contain chemicals that are harmful to the environment.
Do not dispose of batteries in the general household trash.
Viewing TV using the 3D function
IMPORTANT HEALTH AND SAFETY INFORMATION FOR 3D PICTURES. Read and
understand the following safety information before using the TV’s 3D function.
WARNING
• Some viewers may experience discomfort while viewing 3D TV such as dizziness, nausea and headaches. If you
experience any such symptom, stop viewing 3D TV, remove the 3D Active Glasses, and rest.
• Watching 3D images for an extended period of time may cause eye strain. If you feel eye strain, stop viewing 3D
TV, remove your 3D Active Glasses, and rest.
• A responsible adult should frequently check on children who are using the 3D function. If there are any reports of
tired eyes, headaches, dizziness, or nausea, have the child stop viewing 3D TV and rest.
• Do not use the 3D Active Glasses for other purposes (such as general eyeglasses, sunglasses, protective
goggles, etc.)
• Do not use the 3D function or 3D Active Glasses while walking or moving around. Using the 3D function or 3D
Active Glasses while moving around may result in injuries caused by running into objects, tripping, and/or falling.
4
English
HW-D7000_XAA_0321.indd 4
2011-03-21
2:00:48
Cautions on Handling and Storing Discs
Small scratches on the disc may reduce sound
and picture quality or cause skipping.
Be especially careful not to scratch discs when
handling them.
Holding discs
• Do not touch the playback side of the disc.
• Hold the disc by the edges so that
fingerprints will not get on the
surface.
• Do not stick paper or tape on the disc.
Disc Storage
• Do not keep in direct sunlight
• Keep in a cool ventilated area
• Keep in a clean protection jacket and store
vertically.
✎ NOTE
 Do not allow the discs to become contaminated with
dirt.
 Do not load cracked or scratched discs.
Handling and Storing Discs
If you get fingerprints or dirt on the disc, clean it with a
mild detergent diluted in water and wipe with a soft cloth.
• When cleaning, wipe gently from the inside to
the outside of the disc
✎ NOTE
 Condensation may form if warm air comes into
contact with cold parts inside the product. When
condensation forms inside the product, it may not
operate correctly. If this occurs, remove the disc
and let the product stand for 1 or 2 hours with the
power on.
License
• Dolby and the double-D symbol are registered trademarks of Dolby
Laboratories.
• "Manufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535; 7,392,195; 7,272,567;
7,333,929; 7,212,872 & other U.S. and worldwide patents
issued & pending. DTS and the Symbol are registered
trademarks, & DTS-HD, DTS-HD Master Audio | Essential and
the DTS logos are trademarks of DTS, Inc. Product includes
software. © DTS, Inc. All Rights Reserved."
• "ABOUT DIVX VIDEO: DivX® is a digital video format
created by DivX, Inc. This is an official DivX
Certified® device that plays DivX video. Visit www.divx.com for more
information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be
registered in order to play purchased DivX Video-on-Demand (VOD)
movies. To obtain your registration code, locate the DivX VOD section in
your device setup menu. Go to vod.divx.com for more information on
how to complete your registration.
DivX Certified® to play DivX® video up to HD 1080p, including
premium content.
DivX®, DivX Certified® and associated logos are trademarks of DivX,
Inc. and are used under license."
Covered by one or more of the following U.S. patents : 7,295,673;
7,460,668; 7,515,710; 7,519,274
• HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing
LLC in the United States and other countries.
• Oracle and Java are registered trademarks of Oracle and/or its
affiliates. Other names may be trademarks of their respective owners.
• This item incorporates copy protection technology that is protected by
U.S. patents and other intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are prohibited.
• Blu-ray Disc™, Blu-ray™, and the logos are trademarks of Blu-ray
Disc Association.
• iPod is a trademark of Apple Inc.,
registered in the U.S. and other
countries. iPhone is a trademark of
Apple Inc.
• < Open Source License Notice >
In the case of using open source software, Open Source
Licenses are available on the product menu.
Copyright
© 2011 Samsung Electronics Co., Ltd. All rights reserved.
English
HW-D7000_XAA_0321.indd 5
5
2011-03-21
2:00:48
Contents
2
3
4
5
5
5
Safety Warnings
Important Safety Instructions
Precautions
Cautions on Handling and Storing Discs
License
Copyright
GETTING STARTED
8
10
11
15
16
16
18
19
Key features of your new Blu-ray Receiver
Icons that will be used in manual
Disc Types and Characteristics
Accessories
Description
Front Panel
Rear Panel
Remote Control
CONNECTIONS
21
22
23
24
25
26
27
28
29
30
31
31
32
Speaker Positioning
Attaching the Toroidal Ferrite Core to the Power Cord of
the Main Unit
Connecting the Speakers
Connecting the Bi-AMP Speaker
Connecting External Devices/your TV via HDMI
Connecting to your TV
Connecting a Cable, Satellite or Set-top Box
Connecting a Game Console
Connecting a CD Player
Video Conversion Flow According to the Connected Port
Connecting the FM Antenna
Connecting AUX Components
Connecting to a Network
34
35
36
36
37
37
37
37
39
39
39
39
39
39
40
40
42
43
44
44
44
45
45
45
45
47
47
47
Initial Settings
Accessing the Settings Menu
Display
3D Settings
TV Aspect (Picture Size and Format)
Smart Hub Screen Size
BD Wise (Samsung Products only)
Resolution
HDMI Color Format
Movie Frame (24 Fs)
HDMI Deep Color
Still Mode
Progressive Mode
Video Conversion
Audio
Speaker Settings
Musical Room Calibration
Surround
Crossover Frequency
MP3 Enhancer
Smart Volume
Dual Mono
HDMI Audio
Audio Return Channel
Digital Output
Dynamic Range Control
HDMI Auto Sync
Audio Sync
SAFETY INFORMATION
2
8
21
SETUP
34
6
English
HW-D7000_XAA_0321.indd 6
2011-03-21
2:00:48
47
47
50
50
51
51
51
51
51
51
52
52
52
52
52
52
52
52
52
53
53
53
55
Network
Network Settings
Network Status
BD-LIVE Internet Connection
System
Initial Settings
Anynet+ (HDMI-CEC)
BD Data Management
Input Selection
Time Zone
DivX® Video On Demand
Reset
Language
Security
BD Parental Rating
DVD Parental Rating
Change Password
General
Front Display
Network Remote Control
Support
Software Upgrade
Contact Samsung
BASIC FUNCTIONS
56
56
57
57
58
58
59
61
63
65
66
67
68
68
69
Playing a Disc
Using the Disc menu / Title menu / Popup menu
Playing the Title List
Using the Search and Skip Functions
Slow Motion Play/Step Motion Play
Repeat Playback
Using the TOOLS button
Listening to Music
Sound Mode
Playing back a Picture
Playing back a USB Storage Device
Listening to Radio
Connecting an iPod/iPhone Using the USB Cable
Connecting an iPod/iPhone Using the Dock
iPod/iPhone Models You Can Use with This Product
NETWORK SERVICES
70
77
79
79
79
Using Smart Hub
Samsung Apps
Using vTuner Function
BD-LIVE™
Using the AllShare Function
OTHER INFORMATION
80
84
Troubleshooting
Specifications
47
56
70
80
•
ENGLISH
SETUP
Figures and illustrations in this User Manual are provided for reference only and may differ from actual product
appearance.
English
HW-D7000_XAA_0321.indd 7
7
2011-03-21
2:00:48
Getting Started
Key features of your new Blu-ray Receiver
Product Features
Digital Receiver
This product is a pure digital receiver that performs digital signal processing to minimize signal distortion
and loss.
3D
This product can play 3D contents through an HDMI cable.
To implement the 3D effect, connect a 3D TV to the product using an HDMI cable, and play the 3D
content while wearing 3D vision glasses.
Smart Hub
You can download various for pay or free-of charge applications through a network connection. These
applications provide a range of Internet services and content including news, weather forecasts, stock
market quotes, games, movies, and music.
AllShare
You can play videos, music and photos saved on your devices (such as your PC, mobile phones or
NAS) through the home theater via a network connection.
Audio Sync function
If you have connected the product to a digital TV, video can sometimes lag behind the audio.
To compensate for this, you can adjust the audio delay time so that the audio syncs with the video.
iPod SYNC function
If the video signal from an iPod player you attached to the product lags behind the audio signal during
playback, you can set the audio delay time so that the video and audio match.
iPod & iPhone support
If you have connected an iPod player to the home theater using the iPod/iPhone specific USB cable, you
can play the music files in the iPod/iPhone through the connected speakers.
BD Wise
BD Wise automatically adjusts BD Wise-compliant Samsung products to their optimal settings.
This feature is enabled only if BD Wise-compliant Samsung products are connected to each other using
an HDMI cable.
3D SOUND
You can enjoy more natural and vivid surround sound with enriched tones.
ARC (Audio Return Channel)
You can enjoy TV sound from the Home Theater speakers by using just one HDMI cable.
8
English
HW-D7000_XAA_0321.indd 8
2011-03-21
2:00:48
01
Adds a surround back channel for more spacious sound compared to regular 5.1 channel Dolby Digital.
Dolby Pro Logic llx
Dolby Pro Logic IIx is a new technology that provides discrete 7.1 channels out of 2 channel or multi
channel sources.It also provides Music,Movie and Game modes.
Dolby Pro Logic IIx is an improved surround system that is optimized to a 7.1 CH multimedia system,
enabling you to maximize your entertainment experience.
Getting Started
DOLBY DIGITAL EX
Dolby Pro Logic llz
Dolby Pro Logic IIz adds front height channels to surround sound, creating a 7.1 playback system for
video games, home music, and movies; bringing enhanced spatial effects and enveloping sound.
Dolby Digital Plus
Dolby Digital Plus is the next-generation audio technology for all high-definition programming and media.
Dolby True-HD
Dolby True-HD is Dolby’s next-generation lossless technology developed for high-definition disc-based
media.
DTS (Digital Theater Systems)
DTS provides a discrete 5.1 CH digital audio signal for both music and movie contents and uses less
compression than Dolby Digital for richer sound.
DTS Neo 6
Provides a full range of 6 channels by converting a digital PCM or analog stereo signal using DTS digital
matrix decoding.
DTS 96/24
DTS 96/24 encodes standard 16 bit/44.1 kHz sound to 24 bit/96kHz and applies it to a 5.1 CH sound
track.
DTS-ES (Extended Surround) Direct 6.1
The DTS-ES (Extended Surround) system is a new multi digital signal format that was developed by Digital
Theater Systems Inc.
Supporting full compatibility with the conventional DTS digital surround sound format, the DTS-ES
(Extended Surround) system improves the surround signal for a 360-degree surround effect.
DTS-ES adds an additional rear center surround channel for 6.1 channel sound.
DTS-HD MA (Digital Theater Systems - Master Audio, High Resolution)
DTS-HD Audio provides the highest quality multi-channel sound possible.
It delivers sound quality that matches the clear and vivid images of high-definition video.
SFE (Sound Field Effect) Using 32bit Audio Digital Signal Processing
Provides more realistic surround sound with normal stereo audio sources.
✎ NOTE

Write as "VFD" when it is BD/DVD mode :
- DTS ES Discrete : Write as "DTS ES"
-DTS ES Matrix, normal DTS : Write as "DTS"
English
HW-D7000_XAA_0321.indd 9
9
2011-03-21
2:00:48
Getting Started
Icons that will be used in manual
Make sure you understand the following terms before reading the rest of the user manual.
Term
Logo
Icon
h
z
Z
BD-ROM
BD-RE/-R
DVD-VIDEO
Definition
Indicates a function available on a BD-ROM.
Indicates a function available on a BD-RE/-R disc recorded in the
BD-RE format.
Indicates a function available on a DVD-VIDEO.
DVD-RW(V)
DVD-R
y
DVD+RW
Indicates a function available on recorded DVD+RW or DVD-RW(V)/DVDR/+R discs that have been recorded and finalized.
DVD+R
MP3
WMA
-
JPEG
-
o
w
G
DivX
MKV
MP4
DivX
x
Audio CD
USB storage
device
-
CAUTION
-
NOTE
-
Shortcut Key
-
F
!
✎
Indicates a function available on an audio CD-RW/-R (CD-DA format).
Indicates a function available in a CD-RW/-R, DVD-RW/-R disc or a USB
storage media containing MP3 or WMA contents.
Indicates a function available in a CD-RW/-R, DVD-RW/-R disc or a USB
storage media containing JPEG contents.
Indicates a function available in a CD-RW/-R, DVD-RW/-R disc or a USB
storage media containing DivX contents.
Indicates a function available on a USB storage device.
Indicates a situation where a function does not operate or settings may be
cancelled.
Indicates tips or instructions that can help you operate a function better.
Indicates that you can access this function quickly and easily by
pressing a button on the remote control.
• This product is compatible with the NTSC color system only.
• PAL discs will not play.
10
English
HW-D7000_XAA_0321.indd 10
2011-03-21
2:00:48
01
Logos of Discs that can be played
Blu-ray Disc Compatibility
Blu-ray is a new and evolving format. Accordingly, disc
compatibility issues are possible. Not all discs are
compatible and not every disc will play back. For
additional information, refer to the Disc Types and
Characteristics section of this Manual.
Blu-ray Disc
3D Blu-ray Disc
Dolby Digital Plus
NTSC broadcast system in
U.S.A, Canada, Korea,
Japan
Dolby TrueHD
DTS-HD High Resolution
Audio
Java
DTS-HD Master Audio |
Essential
BD-LIVE
DTS 96/24
DTS Neo 6
DTS-ES
Getting Started
Disc Types and Characteristics
✎ NOTE
 Playback may not work for some types of discs or
when you use specific functions such as angle
change and aspect ratio adjustment. Information
about the discs is written in detail on the box.
Please refer to this if necessary.
 Do not allow discs to become dirty or scratched.
Fingerprints, dirt, dust, scratches, or deposits of
cigarette smoke on the recording surface may
make it impossible to playback a disc.
 When you play a BD-Java title, loading may take
longer than a normal title or some functions may
perform slowly.
Discs that cannot be played
•
•
•
•
•
•
HD DVD Disc
DVD-RAM
3.9 GB DVD-R Disc for Authoring.
DVD-RW(VR mode)
Super Audio CD(except CD layer)
DVD-ROM/PD/MV-Disc, etc CVD/CD-ROM/
CDV/CD-G/CD-I/LD
• CDGs play audio only, not graphics.
✎ NOTE
 Some commercial discs and DVD discs purchased
outside your region may not play on this product.
 If a DVD-R/-RW disc has not been recorded properly
in DVD video format, it will not play on this product.
English
HW-D7000_XAA_0321.indd 11
11
2011-03-21
2:00:50
Getting Started
Region Code
BD-RE/-R
Both the product and the discs are coded by
region. These regional codes must match for the
product to play the disc.If the codes do not
match, the disc will not play.
Blu-ray RE/-R discs can be recorded and played
back. This product can play back a BD-RE/-R disc
recorded by other compatible Blu-ray disc
recorders.
DVD-VIDEO
Disc Type
Blu-ray
Region
Code
Area
A
North America, Central America,
South America, Korea, Japan,
Taiwan, Hong Kong and South
East Asia.
B
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
• This product can play back pre-recorded commercial
DVD discs (DVD-VIDEO discs) with movies.
• When switching from the first layer to the second
layer of a dual-layered DVD-VIDEO disc, there
may be momentary distortion in the image and
sound. This is not a malfunction of the product.
DVD-RW/-R/+R
This product can play back a DVD-RW/-R/+R disc
recorded and finalized with a DVD video recorder.
The ability to play back may depend on recording
conditions.
C
India, China, Russia, Central and
South Asia.
1
The U.S., U.S. territories and
Canada
• This product can play back a DVD+RW disc
recorded with a DVD Video recorder. The ability to
play back may depend on recording conditions.
2
Europe, Japan, the Middle East,
Egypt, South Africa, Greenland
Audio CD (CD-DA)
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
4
Mexico, South America, Central
America, Australia, New Zealand,
Pacific Islands, Caribbean
5
Russia, Eastern Europe, India,
most of Africa, North Korea,
Mongolia
6
China
DVD+RW
DVD-VIDEO
Disc Types
• This product can play back CD-DA format audio
CD-RW/-R discs.
• The product may not be able to play some CDRW/-R discs due to the condition of the
recording.
CD-RW/-R
• Use 700MB (80 minute) CD-RW/-R discs. Do not
use 800MB (90 minute) or larger discs, as these
discs may not play back.
• If the CD-RW/-R disc was not recorded as a
closed session, you may experience delays when
playing back the beginning of the disc or all
recorded files may not play.
• Some CD-RW/-R discs may not play on this
product, depending on the device which was
used to burn them. For contents recorded on CDRW/-R media from CDs for your personal use,
playability may vary depending on the contents
and discs.
BD-ROM
Blu-ray discs can only be played back.
This product can play back pre-recorded
commercial BD-ROM discs.
12
English
HW-D7000_XAA_0321.indd 12
2011-03-21
2:00:51
01
Using JPEG discs
• The home theater can play back D-R/-RW, DVD-RW/-R discs recorded in the UDF or JOLIET format.
• Only JPEG files with the ".jpg", ".JPG", ".jpeg" or "JPEG" extension can be displayed.
• Progressive JPEG is supported.
Getting Started
Disc Format
DVD-RW/-R (V)
• This format is used for recording data on DVD-RW or DVD-R discs. This product can play DVD-RW or DVD-R
discs if they have been finalized.
• If a disc that has been recorded in Video Mode by a different maker’s recorder but has not been finalized, it
cannot be played by this product.
Supported File Formats
Video File Support
File Extension
Container
Video Codec
DivX 3.11/4.x/5.1/6.0
XviD
*.avi
AVI
H.264 BP/MP/HP
MPEG4 SP/ASP
Motion JPEG
DivX 3.11/4.x/5.1/6.0
XviD
*.mkv
MKV
H.264 BP/MP/HP
MPEG4 SP/ASP
Motion JPEG
DivX 3.11/4.x/5.1/6.0
XviD
*.asf
ASF
H.264 BP/MP/HP
MPEG4 SP/ASP
Motion JPEG
*.wmv
ASF
*.mp4
MP4
MP3
AC3
LPCM
ADPCM
DTS Core
MP3
AC3
LPCM
ADPCM
DTS Core
MP3
AC3
LPCM
ADPCM
WMA
Resolution
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
Window Media Video v9
WMA
1920x1080
H.264 BP/MP/HP
MP3
ADPCM
AAC
1920x1080
ADPCM
AAC
HE-AAC
1920x1080
MPEG4 SP/ASP
XVID
H.264 BP/MP/HP
*.3gp
Audio Codec
3GPP
MPEG4 SP/ASP
1920x1080
1920x1080
1920x1080
English
HW-D7000_XAA_0321.indd 13
13
2011-03-21
2:00:52
Getting Started
File Extension
Container
*.vro
VRO
VOB
Video Codec
Audio Codec
Resolution
MPEG2
AC3
MPEG
LPCM
1920x1080
AC3
MPEG
LPCM
AAC
352x288
MPEG1
MPEG1
*.mpg
*.mpeg
MPEG2
PS
H.264
1920x1080
1920x1080
AC3
AAC
MP3
DD+
HE-AAC
MPEG2
*.ts
*.tp
*.trp
352x288
H.264
TS
VC1
1920x1080
1920x1080
1920x1080
Restrictions
•
•
•
•
•
Some of the Codecs listed above will not play if there is a problem with the contents.
Corrupt video sources or sources with incorrect container information will not play properly.
AV sources that exceed the standard bit rate or frame rate may not play properly.
If the index table is corrupt, the Seek (Jump) function will not be supported.
If you play a video via the network, it may not play properly depending on the network status.
Video decoder
• Up to H.264 Level 4.1 supported.
• H.264 FMO/ASO/RS, VC1 SP/MP/AP L4, AVCHD not supported.
• XVID, MPEG4 SP, ASP :
- Below 1280 x 720: 60 frame max
- Above 1280 x 720: 30 frame max
• GMC 2 or higher not supported.
Audio decoder
•
•
•
•
Up to WMA 7,8,9 supported.
WMA 9 PRO with more than two channels (multi-channel) not supported.
WMA 9 Lossless, Voice not supported.
WMA sampling rate at 22050Hz mono not supported.
Music File Support
File Extension
Container
Audio Codec
*.mp3
MP3
MP3
-
WMA
Compliant with WMA version 10
* Sampling rates (in kHz) - 8, 11, 16, 22, 32,
44.1, 48
* Bit rates - All bit-rates in the range 5kbps to
384kbps
*.wma
14
WMA
Support Range
English
HW-D7000_XAA_0321.indd 14
2011-03-21
2:00:52
01
Supported devices:
USB storage media, MP3 player, digital camera,
USB card reader
1) The product does not support folder or file
names longer than 125 characters.
2) A subtitle file bigger than 300 KB may not be
properly displayed.
3) Some USB/digital camera devices may not
be compatible with the product.
4) The praoduct supports the FAT16 and FAT32
file systems.
5) Photo (JPEG), music (MP3,) and video files
must have Korean or English file names.
Otherwise, the files will not play.
6) Connect USB devices directly to the
product's USB port. Connecting through a
USB cable may cause compatibility
problems.
7) Inserting more than one memory device into
a multi-card reader may cause the reader to
operate improperly.
8) The product does not support the PTP
protocol for digital cameras
9) Do not disconnect a USB device during a
"loading" process.
10) The bigger the image resolution, the longer
the image takes to display.
11) This player cannot play MP3 files with DRM
(Digital Rights Management) downloaded
from commercial sites.
Getting Started
Notes on the USB connection
Accessories
Check the box for the supplied accessories listed below.
INPUT SELECT
TV SOURCE
POWER
BD-RX
TV
SHIFT
1
2
4
3
5
6
SLEEP
(For Power cord)
TONE
9
7
8
S.DIRECT
AUDIO ASSIGN
FULL
SCREEN
0
REPEAT
MUTE
TUNING
/CH
VOL
SFE MODE
DISC MENU
MENU
TITLE MENU
POPUP
TOOLS
INFO
RETURN
EXIT
iPod SYNC
TUNER
MEMORY
MO/ST
A
B
C
D
SMART
SEARCH
vTuner
2D → 3D
3D SOUND
NEO:6
HUB
NETFLIX
Video Cable
(AH39-40001V)
FM Antenna
(AH42-00017A)
Toroidal Ferrite Core
(3301-000144)
User's Manual
(AH68-02334S)
iPod Dock
(AH96-00051B)
ASC Microphone
(AH30-00099A)
Remote Control
(AH59-02377A)/
Batteries (AAA size)
(4301-000116)
English
HW-D7000_XAA_0321.indd 15
15
2011-03-21
2:00:52
Getting Started
Description
Front Panel
1
2 3
4
5
6
7
8
INPUT SELECT
MASTER VOLUME
ASC MIC
SELECT
TONE
CONTROL
Smart HUB
S.Direct
vTuner
10
9
AV SYNC
TUNING
MODE
MEMORY
MENU
RETURN
AUDIO
ASSIGN
AUDIO
EFFECT
VIDEO
AUDIO
PHONES
3D SOUND
AUX 1 IN
11 12 13 14 15 16
17
18 19
20
21 22 23 24
25 26
27
28
1
INPUT SELECT
Used to select a source.
BD/DVD SAT GAME AUX1 AUX2 CD R-IPOD FM TV
2
3
4
5
6
REMOTE CONTROL SENSOR
Detects signals from the remote control.
DISC SLOT
Insert disc here.
STOP BUTTON
Stops disc playback.
PLAY/PAUSE BUTTON
Plays a disc or pauses playback.
ENTER BUTTON
Selects menu items.
7
8
9
10
OPEN/CLOSE BUTTON
Ejects a Disc.
DISPLAY
Displays the playing/audio input status, time, listening mode, etc.
MASTER VOLUME
Adjusts the volume level.
16
POWER BUTTON (
)
Turns the product on and off.
English
HW-D7000_XAA_0321.indd 16
2011-03-21
2:00:53
01
TONE CONTROL BUTTON
Used to set the bass, treble level and tone to on/off.
SMART HUB BUTTON
Display the Smart Hub service screen.
13
S.DIRECT BUTTON
Used to select the S.DIRECT mode.
(Output the original signal as it is without applying the sound field effect or any
other sound effect.
14
15
16
vTuner BUTTON
Used to select the vTuner.
AV SYNC BUTTON
Used to set the Audio Delay.
TUNING MODE BUTTON
Used to select the Manual or Preset mode for FM radio.
17
18
19
SELECT BUTTON
Used to change the radio frequency.
MEMORY BUTTON
Used to set a preset radio frequency.
MENU BUTTON
Display the home menu screen.
20
UP(,), DOWN(.), LEFT(<),
RIGHT(>) BUTTONS
Used to move the cursor up, down, left or right.
21
22
23
24
25
RETURN BUTTON
Return to the previous menu.
AUDIO ASSIGN BUTTON
Toggles to select an input mode for the selected source.
AUDIO EFFECT BUTTON
Toggles to select a surround sound mode.
3D SOUND BUTTON
Used to set the 3D sound.
ASC MIC JACK
Used to connect the ASC Microphone for setting up MRC (Musical Room Calibration).
26
USB PORT
You can connect a USB memory flash stick here and use it as storage when the product is
connected to BD-LIVE. You can also use the USB Host for software upgrades and MP3/
JPEG/DivX/MKV/MP4 playback.
27
AUX 1 IN JACKS
Auxiliary AV input terminals used to connect a camcorder, portable DVD player
or gaming device.
28
PHONES JACK
Used to connect a set of headphones or earphones.
Getting Started
11
12
✎ NOTE
 You must use a USB memory flash stick to perform a software upgrade using the USB Host jack.
 When the product displays the Blu-ray disc menu, you cannot start the movie by pressing the PLAY button on the
product or the remote. To play the movie, you must select Play Movie or Start in the disc menu, and then press the
ENTER button.
English
HW-D7000_XAA_0321.indd 17
17
2011-03-21
2:00:54
Getting Started
Rear Panel
1
2 3
4
LAN
iPod
5
6
HDMI OUT
HDMI IN
ARC
(MONITOR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
FM ANT
7
GAME
TV
CD
AUDIO IN
8
IN
9
OUT
10
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
11
SPEAKERS OUT
12 13
14
1
VIDEO IN JACKS
Receives the video signal from a video player (SAT, GAME, TV).
2
VIDEO OUT JACK
Outputs the video signal to video devices (TV, Projector etc).
3
LAN TERMINAL
Can be used for network based services (see pages 70~79),
BD-LIVE and software upgrade under the network connection.
4
iPod JACK
Connect the iPod dock connector here.
5
HDMI OUT JACK
Outputs digital video and audio signals simultaneously using an
HDMI cable.
6
HDMI IN JACKS
Receives digital video and audio signals simultaneously using an
HDMI cable.
7
FM ANTENNA JACK
Connect the FM antenna.
8
AUDIO IN JACKS
Receives the audio signal from a video player (SAT, GAME, TV, CD).
9
COMPONENT VIDEO IN JACKS
Receives the component video signal.
10
COMPONENT VIDEO OUT JACKS
Outputs the component video signal.
11
OPTICAL IN JACKS (DIGITAL AUDIO IN)
Receives the digital optical audio signal.
12
COAXIAL IN JACK (DIGITAL AUDIO IN)
Receives the digital coaxial audio signal.
13
SUBWOOFER AUDIO OUT JACKS
Connect the subwoofers.
14
SPEAKER OUT TERMINALS
The front speaker and surround back speaker ports can be
connected to a speaker that supports bi-amplifying. For connecting
to the bi-amplifier, refer to page 24.
18
English
HW-D7000_XAA_0321.indd 18
2011-03-21
2:00:54
01
Getting Started
Remote Control
Tour of the Remote Control
INPUT SELECT
TV SOURCE
POWER
Turn the product on and off.
To change to TV mode, press the
TV button.
To change to receiver, press the
BD-RX button.
To eject the disc.
BD-RX
TV
SHIFT
1
Press numeric buttons to operate options.
2
4
3
5
6
SLEEP
TONE
9
After pressing the SHIFT button,
7
8
Press to select S.DIRECT mode.
S.DIRECT
AUDIO ASSIGN
FULL
SCREEN
0
or
Press to see the full screen on a TV.
REPEAT
Press to skip backwards or forwards.
Press to stop/play a disc.
TUNING
/CH
VOL
SFE MODE
DISC MENU
MENU
TITLE MENU
Press to view the disc menu.
POPUP
TOOLS
INFO
RETURN
EXIT
Select on-screen menu items and
change menu value.
Return to the previous menu.
Correct the audio synchronization
when playing iPod video content.
These buttons are used both for menus
on the product and also several
Blu-ray Disc functions.
Press to use Smart Hub.
Press to search contents.
Press to apply 3D Sound effect.
Allows you to repeat a title, chapter,
track or disc.
Press to search backwards or
forwards.
Search for active FM stations and
change channels.
You can set the SFE (Sound Field
Effect) mode best suited for the
type of music you are listening to.
Use to enter the popup menu/title
menu.
Use to display the playback
information when playing
a Blu-ray/DVD disc.
Press to exit the menu.
iPod SYNC
TUNER
MEMORY
MO/ST
A
B
C
D
SMART
SEARCH
vTuner
2D → 3D
3D SOUND
NEO:6
HUB
NETFLIX
Press to use Netflix.
You can adjust the bass and
treble level.
Toggles to select an input mode for
the selected source.
MUTE
Adjust the volume.
Press to use the Tools menu.
To use second function of some
button.
After pressing the SHIFT button,
Set a Sleep time to shut off the
product.
Press to pause a disc.
Cut off the sound temporarily.
Press to move to the home menu.
Press to select Blu-ray's mode.
or
Press to select TV's video mode.
Used to set a preset radio frequency.
Select MONO or STEREO for radio
broadcasting.
Press to enjoy an ordinary 2D video
in 3D mode.
Select the desired Dolby Pro
Logic II audio mode.
Press this to use the vTuner.
Select the desired NEO:6 mode.
English
HW-D7000_XAA_0321.indd 19
19
2011-03-21
2:00:55
Getting Started
Installing batteries in the Remote Control
* Battery size: AAA
TV Brand Code List
Brand
Code
Brand
Code
Admiral
(M.Wards)
56, 57, 58
Mitsubishi/
MGA
18, 40, 59, 60, 75
A Mark
01, 15
MTC
18
NEC
18, 19, 20, 40, 59, 60
Anam
01, 02, 03, 04, 05,
06, 07, 08, 09, 10,
11, 12, 13, 14
Nikei
03
Onking
03
01, 18, 40, 48
Onwa
03
Panasonic
06, 07, 08, 09, 54,
66, 67, 73, 74
AOC
✎ NOTE
 Make sure to match the “+” and “–” ends of
the batteries with the diagram inside the
compartment.
 Assuming typical TV usage, the batteries last
for about one year.
 The remote control can be used up to
approximately 23 feet (7 meters) in a straight line.
Setting the Remote Control
You can control certain functions of your TV with
this remote control.
When operating a TV with the remote control
1. Press the TV button to set the remote control
to TV mode.
2. Turn on your TV.
3. While holding down the POWER button, enter
the code corresponding to your brand of TV.
• If there is more than one code listed for
your TV in the table, enter one at a time to
determine which code works.
• Example : For a Samsung TV
While holding down the POWER button, use the
number buttons to enter 00. If that does not
work, try 15, then 16, etc.
4. If the TV turns off, the setting is complete.
• You can use the TV POWER, VOLUME,
CHANNEL, and Numeric buttons (0~9).
✎ NOTE
 The remote control may not work on some
brands of TV's. Also, some operations may not
be possible, depending on your brand of TV.
 The remote control will work with Samsung TVs
by default.
20
Bell &
Howell
(M.Wards)
57, 58, 81
Brocsonic
59, 60
Candle
18
Penney
18
Philco
03, 15, 17, 18, 48,
54, 59, 62, 69, 90
Philips
15, 17, 18, 40,
48, 54, 62, 72
Cetronic
03
Citizen
03, 18, 25
Cinema
97
Pioneer
63, 66, 80, 91
Classic
03
Portland
15, 18, 59
Concerto
18
Proton
40
Contec
46
Quasar
06, 66, 67
Coronado
15
Craig
03, 05, 61, 82, 83, 84
Radio
Shack
17, 48, 56, 60,
61, 75
Croslex
62
03
RCA/
Proscan
18, 59, 67, 76, 77,
78, 92, 93, 94
Crown
Curtis
Mates
Realistic
03, 19
59, 61, 63
CXC
03
Daewoo
02, 03, 04, 15, 16,
17, 18, 19, 20, 21,
22, 23, 24, 25, 26,
27, 28, 29, 30, 32,
34, 35, 36, 48, 59, 90
Daytron
40
Dynasty
03
Emerson
03, 15, 40, 46, 59, 61,
64, 82, 83, 84, 85
Fisher
19, 65
Funai
03
Futuretech
03
General
Electric (GE)
06, 40, 56, 59,
66, 67, 68
Hall Mark
40
Hitachi
15, 18, 50, 59, 69
Inkel
45
JC Penny
56, 59, 67, 86
JVC
70
KTV
59, 61, 87, 88
KEC
03, 15, 40
KMC
15
LG
(Goldstar)
01, 15, 16, 17, 37, 38,
39, 40, 41, 42, 43, 44
Sampo
40
Samsung
00, 15, 16, 17, 40,
43, 46, 47, 48, 49,
59, 60, 98
Sanyo
19, 61, 65
Scott
03, 40, 60, 61
Sears
15, 18, 19
Sharp
15, 57, 64
Signature
2000
(M.Wards)
57, 58
Sony
50, 51, 52, 53, 55
Soundesign
03, 40
Spectricon
01
SSS
18
Sylvania
18, 40, 48, 54,
59, 60, 62
Symphonic
61, 95, 96
Tatung
06
Techwood
18
Teknika
03, 15, 18, 25
TMK
18, 40
Toshiba
19, 57, 63, 71
Vidtech
18
Videch
59, 60, 69
Luxman
18
Wards
LXI
(Sears)
15, 17, 18, 40,
48, 54, 60, 64
19, 54, 56, 59,
60, 62, 63, 65, 71
Yamaha
18
York
40
Magnavox
15, 17, 18, 48, 54,
59, 60, 62, 72, 89
Yupiteru
03
Marantz
40, 54
Zenith
58, 79
Matsui
54
Zonda
01
MGA
18, 40
Dongyang
03, 54
English
HW-D7000_XAA_0321.indd 20
2011-03-21
2:00:56
02
Connections
Speaker Positioning
Connections
This section involves various methods of connecting the receiver to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
There are two methods for positioning the speakers.
FHL
FHR
6.6~9.8 feet (2~3m)
6.6~9.8 feet (2~3m)
RECEIVER
RECEIVER
SL
SR
SBL
SL
SR
SBR
L, R, C, SW, SL, SR, SBL, SBR ( Dolby Pro Logic IIx )
L, R, C, SW, SL, SR, FHL, FHR( Dolby Pro Logic IIz)
Position of Receiver
Place the Receiver on a dedicated stand or rack.
Subwoofer g
The position of the subwoofer is not so critical. Place it anywhere you like.
Front Speakers
Place these speakers in front of your listening position, facing inwards (about 45°) toward you.
Place the speakers so that their tweeters will be at the same height as your ears.
Align the front face of the front speakers with the front face of the center speaker or place them slightly in
front of the center speaker.
Center Speaker
It is best to install it at the same height as the front speakers.
You can also install it directly over or under the TV.
Surround Speakers
Place these speakers behind your listening position.
If there isn't enough room, place these speakers so they face each other.
Place them about 2 to 3 feet (60 to 90cm) above your ears, facing slightly downward.
Unlike the front and center speakers, the surround speakers are used to handle mainly sound effects and
sound will not come from them all the time.
English
HW-D7000_XAA_0321.indd 21
21
2011-03-21
2:00:57
Connections
Surround Back Speakers
SBL SBR
If you are using two surround center speakers, place them behind the listening position.
Place the surround back speaker about 2.3-3.3 feet (70 cm to 1 m).
Front Height Speakers
FHL FHR
(Using Dolby Pro Logic IIz)
When using Dolby Pro Logic IIz, place the Surround Back Speakers on the FHL, FHR position above the
front L and front R speakers at least 3.3 feet(1 m) above each one.
Speaker Configuration
For the best surround-sound experience, you should connect seven speakers and a powered
subwoofer. The following table shows which channels you should use based on the number of
speakers you have.
2 speakers
3 speakers
4 speakers
5 speakers
6 speakers
7 speakers
7 speakers
(DPL IIx)
(DPL IIz)
SBL
FHL
SBR
FHR
SBL
✎ NOTE
 No matter how many speakers you use, a powered subwoofer is recommended for powerful and solid bass.
 If you place a speaker near your TV set, screen color may be distorted because of the magnetic field
generated by the speaker. If this occurs, place the speaker away from your TV set.
Attaching the Toroidal Ferrite Core to the Power Cord of the Main Unit
If you attach a Toroidal ferrite core to the power cord, it will help to prevent RF interference from
radio signals.
1. Pull the fixing tab of the Totoidal ferrite core to
open it.
2. Make a loop in the power cord.
3. Attach the Toroidal ferrite core to the power cord as
the figure shows and press it until it clicks.
22
LAN
HDMI OUT
iPod
HDMI IN
ARC
(MONITOR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
FM ANT
GAME
TV
AUDIO IN
CD
IN
OUT
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
SPEAKERS OUT
English
HW-D7000_XAA_0321.indd 22
2011-03-21
2:00:58
02
Connecting the Speakers
Connections
Connecting Speaker Wire
1. Loosen the knob by turning counterclockwise.
2. Insert the bare part of the wire into the hole in the side of each
terminal.
3. Tighten the knob by turning clockwise to secure the wire.
FRONT (R) SURROUND (R) SURROUND BACK (R)
SURROUND BACK (L) SURROUND (L) FRONT (L)
ACTIVE SUBWOOFER
FRONT
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
SUBWOOFER
OUT
SPEAKERS OUT
LAN
HDMI OUT
iPod
MDMI IN
A
ARC
RC
(MONITOR)
(M
MONITOR
OR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
CENTER
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
M
ON TOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
GAME
FM ANT
SAT
TV
AUDIO IN
CD
IN
OUT
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
SPEAKERS OUT
✎ NOTE
 Keep the subwoofer speaker out of reach of children to prevent them from inserting their hands or
objects into the duct (hole).
 Never touch speaker terminals while the power is on. Doing so could result in electric shock.
 Make sure the polarities (+ and -) are correct.
 If you want to use two active subwoofer speakers, connect both subwoofer speakers into the
SUBWOOFER OUT terminals in the rear panel.
 We recommend more than 120W of permited input and connection with speaker that more than
4ohm impedance.
If you use lower level products than our recommend, it can be cause of Speaker Unit or Amplifer's
trouble so be cations about it.
English
HW-D7000_XAA_0322.indd 23
23
2011-03-22
9:22:55
Connections
Connecting the Bi-AMP Speaker
Connect the tweeter (high range) port and woofer (low range) to the front port and surround back speaker
port respectively as appropriate. Then, you can use the bi-amplifi cation feature that supports enriched high
range and base tones.
Bi-AMP Speaker R
Bi-AMP Speaker L
FRONT
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Tweeter
Tweeter
Woofer
Woofer
SPEAKERS OUT
LAN
HDMI OUT
iPod
HDMI IN
ARC
ARC
(M
MONITOR
OR)
(MONITOR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
M
ON TOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
FM ANT
GAME
TV
AUDIO IN
CD
IN
OUT
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
SPEAKERS OUT
! CAUTION
 If Bi-amp is active, you may encounter a restricted access if you have not removed the shorting bar
(like a jumper) in both tweeter and subwoofer ports in the front speaker.
 Before you can use bi-amp, ensure that you use a speaker that supports bi-amplifying.
✎ NOTE
 To enable the Bi-Amp feature, you must set Surround Back Setup to Bi-AMP in Settings menu. See page 41.
 With the Bi-AMP feature, you can use up to 5.1 channels for speaker output in the main unit.
24
English
HW-D7000_XAA_0321.indd 24
2011-03-21
2:01:13
02
HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray
player, set-top box and more.
Connections
Connecting External Devices/your TV via HDMI
HDMI removes any loss of signal from analog conversion, enabling you to enjoy video and audio sound
quality as it was originally created in the digital source.
HDTV Tuner
(HDTV Terrestrial Receiver)
or
SAT (Satellite/Set top box)
Game Console
Camcorder
or
LAN
HDMI OUT
iPod
HDMI IN
ARC
(MONITOR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
M
ON TOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
FM ANT
GAME
TV
AUDIO IN
CD
IN
OUT
If your TV supports ARC
function, connect to ARC
support port of TV.
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
OPTICAL
OUT
SPEAKERS OUT
• Connect it if you want to use
Anynet+. (If connected TV support
ARC, it is not necessary to
connect the OPTICAL OUT.)
High-bandwidth Digital Content Protection System (HDCP) support
To play digital contents through the HDMI connection, both the connected external device and TV
must support High-bandwidth Digital Content Protection System (HDCP). This product supports
HDCP.
Compatibility with a TV Supporting HDMI
A TV with an HDMI jack.
Video/Audio
A TV with a DVI-D jack (TV supporting HDCP)
Video
A TV with a DVI-D jack (TV not supporting HDCP)
-
✎ NOTE
 Audio from SACD discs will not be heard with this connection. To play a DVD disc whose copyright is
protected by CPPM, use a product supporting CPPM.
 The quality of the audio output through the HDMI jack (sampling frequency and bit rate) may be limited by the
performance of the connected device.
 Since HDMI connection supports both video and audio, you don’t have to connect an additional audio cable.
English
HW-D7000_XAA_0321.indd 25
25
2011-03-21
2:01:17
Connections
Connecting to your TV
LAN
HDMI OUT
iPod
HDMI IN
ARC
ARC
(MONITOR)
(M
MONITOR
OR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
FM ANT
GAME
TV
AUDIO IN
CD
IN
OUT
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
SPEAKERS OUT
(not supplied)
or
VIDEO
IN
or
COMPONENT
IN
OPTICAL
OUT
AUDIO
OUT
Video Connection
If your television is equipped with Component Video inputs, connect a Component video cable(not supplied) from
the Component Video Output (PR, PB and Y) jacks on the back of your Receiver to the Component Video Input
jacks on your TV.
OR
Connect the Video cable from the VIDEO OUT (MONITOR) jack on the back of your Receiver to the Video Input
jack on your TV.
Audio Connection
Connect the Digital Input (OPTICAL 3) on your Receiver to the Digital Output of the TV.
OR
Connect AUDIO IN (TV) on your Receiver to the Audio Out of the TV.
26
English
HW-D7000_XAA_0323.indd 26
2011-03-23
2:12:05
02
Connections
Connecting a Cable, Satellite or Set-top Box
COMPONENT
IN
VIDEO
IN
or
LAN
HDMI OUT
iPod
HDMI IN
A
ARC
RC
(M
MONITOR
OR)
(MONITOR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
(not supplied)
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
GAME
TV
AUDIO IN
FM ANT
CD
IN
OUT
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
SPEAKERS OUT
or
SAT(Cable/Satellite/Set-top box)
VIDEO
OUT
AUDIO
OUT
COMPONENT OPTICAL
OUT
OUT
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (SAT) (PR, PB and Y) jacks on the
back of your Receiver to the Component Video Output jacks on your SAT.
OR
Connect a Video cable from the VIDEO IN (SAT) jack on the back of your Receiver to the Video Output jack on
your SAT.
Audio Connection
Connect the Digital Input (OPTICAL 1) on your Receiver to the Digital Output of the SAT.
OR
Connect AUDIO IN (SAT) on your Receiver to the Audio Out of the SAT.
✎ NOTE
 Disconnect the power plug from the outlet if you will not use this unit for a long period of time.
 If the cable/set-top box has only one audio output jack, connect it to either the right or left audio input jack of
the main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
English
HW-D7000_XAA_0321.indd 27
27
2011-03-21
2:01:25
Connections
Connecting a Game Console
COMPONENT
IN
VIDEO
IN
(not supplied)
or
LAN
HDMI OUT
iPod
HDMI IN
A
ARC
RC
(M
MONITOR
OR)
(MONITOR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
GAME
TV
AUDIO IN
FM ANT
CD
IN
OUT
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
SPEAKERS OUT
Game Console
AUDIO
OUT
VIDEO COMPONENT OPTICAL
OUT
OUT
OUT
or
Video Connection
Connect a Component video cable(not supplied) from the COMPONENT IN (Game) (PR, PB and Y) jacks on the
back of your Receiver to the Component Video Output jacks on your Game Console.
OR
Connect a Video cable from the VIDEO IN (Game) jack on the back of your Receiver to the Video Output jack on
your Game Console.
Audio Connection
Connect the Digital Input (OPTICAL 2) on your Receiver to the Digital Output of the Game Console.
OR
Connect AUDIO IN (Game Console) on your Receiver to the Audio Out of the Game Console.
28
English
HW-D7000_XAA_0321.indd 28
2011-03-21
2:01:28
02
Connections
Connecting a CD Player
CD Player
AUDIO
OUT
(not supplied)
LAN
HDMI IN
A
ARC
RC
(MONITOR)
(M
MONITOR
OR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
(not supplied)
or
HDMI OUT
iPod
COAXIAL
OUT
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
M
ON TOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
FM ANT
GAME
TV
AUDIO IN
CD
IN
OUT
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
SPEAKERS OUT
Audio Connection
Connect the Digital Input (COAXIAL) on your Receiver to the Digital Output of the CD Player.
OR
Connect AUDIO IN (CD) on your Receiver to the Audio Out of the CD player.
✎ NOTE
 If the CD player has only one audio output jack, connect it to either the right or left audio input jack of the
main unit. Connect the audio cable's red plug to the red jack and white cable to the white jack.
English
HW-D7000_XAA_0321.indd 29
29
2011-03-21
2:01:32
Connections
Video Conversion Flow According to the Connected Port
As shown in the illustration, if the unit’s HDMI Out is connected to a TV or monitor, the analog video source
(composite or component) from the video device is processed for up-conversion automatically for HDMI output.
If connected to a TV or monitor through Composite or Component ports, corresponding analog signal will be
output respectively, without any conversion. In case if the unit and video source device is connected in multiple
methods (Component and Composite video) at the same time: Video input signal is automatically selected in the
order of Component Video Composite Video.
LAN
HDMI OUT
iPod
HDMI IN
ARC
(MONITOR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
SPEAKER IMPEDANCE : 4~8
COMPONENT IN/OUT
1
(SAT)
MONITOR
FRONT
2
(GAME)
SURROUND
SURROUND BACK
/FRONT HEIGHT
CENTER
SURROUND BACK
SURROUND
/FRONT HEIGHT
FRONT
Y
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
FM ANT
Input
Signal
GAME
TV
AUDIO IN
CD
IN
OUT
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
SPEAKERS OUT
Output
Signal
Video
Conversion
HDMI OUT
HDMI IN
HDMI OUT
HDMI IN
COMPONENT OUT
COMPONENT IN
COMPONENT OUT
COMPONENT IN
VIDEO OUT
VIDEO IN
VIDEO OUT
VIDEO IN
✎ NOTE




This enables upconverting up to a quality of 1080p.
Auto conversion is not applied to a video source incoming from HDMI IN port.
The maximum resolution of the input video signal is 480i, and it will not support higher input resolution.
Video conversion is compatible with the NTSC color system only.
30
English
HW-D7000_XAA_0321.indd 30
2011-03-21
2:01:36
02
1. Connect the FM antenna supplied to the FM ANTENNA terminal as a temporary measure.
2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall
or other rigid surface.
LAN
HDMI OUT
iPod
HDMI IN
ARC
ARC
(M
MONITOR
OR)
(MONITOR)
VIDEO IN
SAT
GAME
HDMI 1
(SAT)
VIDEO OUT
TV
Connections
Connecting the FM Antenna
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
COMPONENT IN/OUT
1
(SAT)
MONITOR
M
ON TOR
F
2
(GAME)
Y
FM ANT
SUBWOOFER
OUT
PB/CB
PR/CR
SAT
GAME
TV
CD
AUDIO IN
FM ANT
IN
OUT
OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL
(SAT)
(GAME)
(TV)
(CD)
FM antenna (supplied)
✎ NOTE
 Do not place the antenna cable close to the power cord. Keep it as far away as possible.
 If you experience poor FM reception, use an external antenna.
Connecting AUX Components
You can connect external devices you use for a short time (camcorder, game console, mobile
equipment,etc.) to the front of this unit for convenience.
INPUT SELECT
MASTER VOLUME
ASC MIC
SELECT
TONE
CONTROL
Smart HUB
S.Direct
vTuner
AV SYNC
TUNING
MODE
MEMORY
MENU
RETURN
AUDIO
ASSIGN
AUDIO
EFFECT
VIDEO
AUDIO
PHONES
3D SOUND
AUX 1 IN
(not supplied)
Camcorder
VIDEO
OUT
AUDIO
OUT
English
HW-D7000_XAA_0321.indd 31
31
2011-03-21
2:01:38
Connections
Connecting to a Network
You can connect this product to a network and use network based services such Smart Hub and BDLIVE (See pages 70~79), as well as receive software upgrades through the network connection. We
recommend using a wireless router or IP router for the connection.
For more information on router connection, refer to the user manual of the router or contact the router
manufacturer for technical assistance.
Cable Network
1. Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the product to the LAN
terminal of your modem.
2. Set the network options. (See page 47)
LAN
iPod
HDMI OUT
ARC
ARC
(M
MONITOR
OR)
(MONITOR)
MDMI IN
HDMI 1
(SAT)
HDMI 2
(GAME)
HDMI 3
(AUX1)
HDMI 4
(AUX2)
Router
Broadband modem
(with integrated router)
Broadband
service
✎ NOTE
Or
Broadband modem
Broadband
service
Networking with PC for
AllShare function
(See page 79)
 Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the
ISP’s policy. For more information, contact your ISP (Internet Service Provider).
 DSL users, please use a router to make a network connection.
 To use the AllShare function, you must connect your PC to the network as shown in the figure.
32
English
HW-D7000_XAA_0321.indd 32
2011-03-21
2:01:42
02
You can connect the Receiver to your network through a wireless IP sharer (router). To set the network
configuration options. see page 47.
Connections
Wireless Network
Broadband
service
Wireless IP sharer
INPUT SELECT
MASTER VOLUME
PC
Networking with PC for
AllShare function
(See page 79)
✎ NOTE
 To use a wireless network, your product must be connected to a wireless IP sharer (router). If the wireless IP sharer
supports DHCP, your product can use a DHCP (dynamic) or static IP address to connect to the wireless network.
 This product supports IEEE 802.11b,g and n. We recommend using IEEE 802.11n. When you play video








over a IEEE 802.11b or g connection, the video may not play smoothly.
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP
sharer is currently being used by another device nearby, this will result in interference and communication failure.
If you select the Pure High-throughput (Greenfield) 802.11n mode and set your routers's Security Encryption
type to WEP, TKIP or TKIPAES (WPS2Mixed), your Samsung home theater will not support the connection in
compliance with new Wi-Fi certification specifications.
If your router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button
Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA
key in either mode.
You can set up the wireless network connection in three ways:
- Using Auto Setup (the Auto Network Search function) through Wireless (General)
- Using WPS(PBC)
- Using One Foot Connection
Wireless LAN, by its nature, may cause interference, depending on the operating conditions.
(router performance, distance, obstacles, interference by other radio devices, etc).
Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
The home theater supports the following security protocols only:
1) Authentication Mode : WEP, WPAPSK, WPA2PSK
2) Encryption Type : WEP, AES
To use the AllShare function, you must connect your PC to your network as shown in the figure.
The connection can be wired or wireless.
English
HW-D7000_XAA_0321.indd 33
33
2011-03-21
2:01:45
Setup
Initial Settings
1. Turn on your TV after connecting the product.
When you connect and turn on the product to a
TV for the first time, the Initial Settings screen
appears.
• Home Menu
My Contents
Videos
Photos
Music
Function
My Devices
Internet
Settings
Initial Settings | On-Screen Language
Select a language for the on-screen displays.
Български
Hrvatski
Dansk
Nederlands
Čeština
English
Eesti keel
Suomi
Français
Deutsch
Ελληνικά
Magyar
Indonesia
Italiano
한국어
m Move " Enter
d WPS(PBC)
✎ NOTE
 The Home menu will not appear if you do not
configure the initial settings except as noted
below.
2. Press the ▲▼◄► buttons to select the desired
language, and then press the ENTER button.
3. Press the ENTER button to select Start.
4. Press the ▲▼ buttons to select the desired TV
Aspect Ratio, and then press the ENTER button.
(See page 37)
If you press the BLUE (D) button to skip
Network Setup, you can access the Home
menu even the Network Setup is not completed.
5. Press the ▲▼ buttons to select the desired
Network Settings : Wired, Wireless
(General), WPS(PBC) or One Foot
Connection, and then press the ENTER
button. If you do not know the details of your
Network Settings, press the BLUE (D) button
on your remote instead to skip Network
Settings here, finish the Initial Settings, and
go to the Home menu.
If you selected a Network Settings, go to
pages 47~50 for more information about the
Network settings. When done, go to Step 6.
 If you press the BLUE (D) button during the
network setup, you can access the Home
menu even if the network setup is not
completed yet.
 If you want to display the Initial Setting screen
again to make changes, select the Initial
Settings. (See page 51)
 If you use an HDMI cable to connect the
product to an Anynet+(HDMI-CEC)compliant Samsung TV and 1.) You have set
the Anynet+(HDMI-CEC) feature to On in
both the TV and the product and 2.) You have
set the TV to a language supported by the
product, the product will select that language
as the preferred language automatically.
 If you leave the product in the stop mode for
more than 5 minutes without using it, a screen
saver will appear on your TV. If the product is
left in the screen saver mode for more than 20
minutes, the power will automatically turn off.
6. The Home menu appears. (For more
information about the Home menu, please
see page 35.)
34
English
HW-D7000_XAA_0321.indd 34
2011-03-21
2:01:45
03
DISC MENU
MENU
3. Press the ▲▼ buttons to select the desired
submenu, and then press the ENTER
button.
TITLE MENU
POPUP
1
TOOLS
Setup
2. Press the ◄► buttons to select Settings,
and then press the ENTER button.
Accessing the Settings Menu
INFO
4. Press the ▲▼ buttons to select the desired
item, and then press the ENTER button.
3
5. Press the EXIT button to exit the menu.
2
RETURN
4
EXIT
✎ NOTE
TUNER
 When the product is connected to a network,
1
MENU Button : Press to move to the Home menu.
2
RETURN Button : Return to the previous menu.
3
ENTER / DIRECTION Button :
Move the cursor or select an item.
Activate the currently selected item.
Confirm a setting.
4
EXIT Button : Press to exit the current menu.
select Internet from the Home menu.
Download the desired content from Samsung
Apps. (See pages 77~79)
 The access steps may differ depending on the
menu you selected.
 The OSD (On Screen Display) may change in
this product after you upgrade the software
version.
To access the Settings menu and sub-menus,
follow these steps:
1. Press the POWER button.
The Home Menu appears.
• Home Menu
My Contents
Videos
3
Photos
Music
4
1
Function
My Devices
Internet
Settings
2
5
d WPS(PBC)
1
Selects My Devices.
2
Selects Function.
3
Selects My Contents.
4
Selects Internet.
5
Selects Settings.
6
Displays the buttons available.
6
English
HW-D7000_XAA_0321.indd 35
35
2011-03-21
2:01:47
Setup
 Depending on the content and the position of
Display
You can configure various display options such as
the TV Aspect Ratio, Resolution, etc.
3D Settings
Screen Size
Select whether to play a Blu-ray Disc with 3D
contents in 3D Mode.
Settings
Display
3D Settings
Audio
System
3D Blu-ray Playback Mode
: Auto
Language
Screen Size
: 55 inch
 If you want to enjoy 3D content, connect a
Security
> Move " Enter ' Return
General
HDMI Deep Color
Lets you enter the actual screen size of your TV so
that the product can adjust the image according to
the screen size and display an optimal 3D image.
(The maximum allowed screen size is 116 inches for
this product.)
! CAUTION
3D Settings
Network
Support
the picture on your TV screen, you may see
vertical black bars on the left side, right side, or
both sides.
: Auto
3D TV to the product’s HDMI OUT port
using a high-speed HDMI cable. Put on 3D
glasses before playing the 3D content.
 The product outputs 3D signals only through
3D Blu-ray Playback Mode
HDMI cable connected to the HDMI OUT
port.
You can choose whether to watch a 3D Blu-ray
disc in 3D or 2D mode before playing the 3D
disc. It is automatically played in 2D mode if your
TV cannot support 3D contents.
• Auto : Automatically detect the 3D capability of
the connected TV and play a 3D Blu-ray disc in 3D
or 2D accordingly.
 As the video resolution in 3D play mode is
• 3D  3D : 3D Blu-ray Discs are played in 3D
mode at all times. If a TV cannot support 3D Bluray discs, the playing screen can be blank.
 Stay at least three times the width of the
• 3D  2D : 3D Blu-ray Discs are played in 2D
mode at all times. Choose this to view a picture
without the 3D effect or when a TV cannot support
3D Blu-ray discs.
✎ NOTE
 To stop a movie during 3D playback, press the
fixed according to the resolution of the
original 3D video, you can not change the
resolution to your preference.
 Some functions such as BD Wise, screen
size adjustment, and resolution adjustment
may not operate properly in 3D play mode.
screen from the TV when watching 3D
images. For example, if you have a 46 inch
screen, stay 138 inches (11.5 feet) from the
screen.
- Place the 3D video screen at eye level for
the best 3D picture.
 When the product is connected to some 3D
devices, the 3D effect may not function
properly.
STOP() button once. The movie stops and the
3D mode option is de-activated.
To change a 3D option selection when you are
playing a 3D movie, press the STOP() button
once. The Blu-ray menu appears. Press the
STOP() button again, then select 3D
Settings in the Blu-ray menu.
36
English
HW-D7000_XAA_0321.indd 36
2011-03-21
2:01:49
03
Depending on the type of television you have, you
may want to adjust the screen size setting.
• 16:9 Original : Select when you connect the
product to a 16:9 TV screen. The product will
display all content in its original aspect ratio.
Content formatted in 4:3 will be displayed with
black bars on the left and right.
• 16:9 Full : Select when you connect the product
to a 16:9 TV screen. All content will fill the full
screen. Content formatted in 4:3 will be stretched.
• 4:3 Letter Box : Select when you connect the
product to a 4:3 TV screen. The product will
display all content in its original aspect ratio.
Content formatted in 16:9 will be displayed with
black bars on the top and bottom.
• 4:3 Pan-Scan : Select when you connect the
product to a 4:3 TV screen. 16:9 content will have
the extreme left and right portions cut off.
✎ NOTE
 Depending on the disc type, some aspect ratios
may not be available.
 If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
then the picture might appear to be distorted.
 If you select the 16:9 Original, your TV may
display 4:3 Pillarbox (black bars on sides of
picture).
Smart Hub Screen Size
Set the Smart Hub Screen to the optimal size.
• Size 1 : The Smart Hub screen size will be smaller
than the default. You may see some black on
sides of screen.
• Size 2 : This is the default setting for Smart Hub.
The product displays the normal Smart Hub
screen size.
• Size 3 : This will display a larger Smart Hub screen
size. The image may be too large for your TV
screen.
BD Wise (Samsung Products only)
BD Wise is Samsung’s latest inter-connectivity
feature.
When you connect a Samsung product and a
Samsung TV with BD Wise to each other via HDMI,
and BD Wise is on in both the product and TV, the
product outputs video at the video resolution and
frame rate of the BD/DVD disc.
• Off : The output resolution stays fixed at the
resolution you set previously in the Resolution
menu, regardless of the resolution of the disc.
See Resolution below.
• On : The product outputs video at the original
resolution and frame rate of the BD/DVD disc.
✎ NOTE
 When BD Wise is on, the Resolution setting
automatically defaults to BD Wise and BD
Wise appears in the Resolution menu.
 If the product is connected to a device that
does not support BD Wise, you can not use
the BD Wise function.
 For proper operation of BD Wise, set the BD
Wise menu of both the product and the TV to On.
Resolution
Lets you set the output resolution of the
Component and HDMI video signal to Auto,
1080p, 1080i, 720p, 480p, or 480i. The number
indicates the number of lines of video per frame.
The i and p indicate interlaced and progressive scan,
respectively. The more lines, the higher the quality.
• Auto : Automatically sets the output resolution to
the connected TV’s maximum resolution.
• BD Wise : Automatically sets the resolution to the
resolution of the BD/DVD disc if you have
connected the product via HDMI to a TV with the
BD Wise feature. (The BD Wise menu item appears
only if BD Wise is set to On. See BD Wise above.)
• 1080p : Outputs 1080 lines of progressive
video. (HDMI only)
• 1080i : Outputs 1080 lines of interlaced video.
• 720p : Outputs 720 lines of progressive video.
• 480p : Outputs 480 lines of progressive video.
English
HW-D7000_XAA_0321.indd 37
Setup
TV Aspect
(Picture Size and Format)
37
2011-03-21
2:01:50
Setup
Resolution according to the output mode
• Blu-ray Disc/E-contents/Digital Contents playback
HDMI / connected
HDMI / not connected
HDMI Mode
Output
Component Mode
Blu-ray Disc
E-contents/
Digital
contents
Component/
VIDEO Mode
Blu-ray Disc
E-contents/
Digital
contents
VIDEO Mode
BD Wise
Resolution of
Blu-ray Disc
[email protected]
480i
-
-
-
Auto
Max.
Resolution of
TV input
Max.
Resolution of
TV input
480i
-
-
-
Setup
[email protected]
[email protected]
[email protected]
480i
-
-
-
Movie Frame :
Auto (24Fs)
[email protected]
[email protected]
480i
-
-
-
1080i
1080i
1080i
480i
480i
1080i
480i
720p
720p
720p
480i
480i
720p
480i
480p
480p
480p
480i
480i
480p
480i
480i
-
-
-
480i
480i
480i
• DVD playback
HDMI / connected
Output
HDMI / not connected
HDMI Mode
Component/VIDEO
Mode
Component Mode
VIDEO Mode
BD Wise
480i
480i
-
-
Auto
Max. Resolution of
TV input
480i
-
-
[email protected]
[email protected]
480i
-
-
1080i
1080i
480i
480p
480i
720p
720p
480i
480p
480i
480p
480p
480i
480p
480i
480i
-
-
480i
480i
Setup
✎ NOTE
 If the TV you connected to the product does not support Movie Frame or the resolution you selected,
the message “If no pictures are shown after the selection, please wait for 15 seconds. And then, the
resolution will be reverted to the previous value automatically. Would you like to make a selection?”
appears.
If you select Yes, the TV’s screen will go blank for 15 seconds, and then the resolution will revert to the
previous resolution automatically.
38
English
HW-D7000_XAA_0321.indd 38
2011-03-21
2:01:50
03
changed the resolution, remove all discs, and
then press and hold the STOP () button on
the front of the product for more than 5
seconds. All settings are restored to the
factory default. Follow the steps on the
previous page to access each mode and
select the Display Setup that your TV will
support.
 When the factory default settings are restored,
all stored user BD data is deleted.
 The Blu-ray Disc must have the 24 frame
feature for the product to use the Movie Frame
(24Fs) mode.
 If both HDMI and Component jacks are
connected and you are currently viewing
Component output, the resolution is fixed to
480i.
HDMI Color Format
Setup
 If the screen stays blank after you have
HDMI Deep Color
Lets you output video from the HDMI OUT jack
with Deep Color. Deep Color provides more
accurate color reproduction with greater color
depth.
• Auto: The product outputs video with Deep
Color to a connected TV which supports HDMI
Deep Color.
• Off : The picture is output without Deep Color.
Still Mode
Lets you set the type of picture the product
displays when you pause DVD playback.
• Auto: Automatically shows the best still picture
depending on the content.
• Frame : Select when pausing a scene with a
little action.
• Field : Select when pausing a scene with a lot
of action.
Lets you set the color space format for HDMI
output to match the capabilities of the connected
device (TV, monitor, etc).
Progressive Mode
• Auto : Automatically sets the product to the
optimum format supported by your device.
• YCbCr (4:4:4) : If your TV supports the YCbCr
color space via HDMI, select this to output the
normal YCbCr color gamut.
• RGB (Standard) : Select RGB (Standard) to
output the normal RGB color gamut.
• RGB (Enhanced) : If you have connected the
product to a DVI display device such as a
monitor, select RGB (Enhanced) to output the
enhanced RGB color gamut.
• Auto : Select to have the product automatically
select the best picture quality for the DVD
you’re watching.
Movie Frame (24 Fs)
• Auto :Converts the incoming video signal
before outputting in the maximum resolution
that the connected TV supports.
Setting the Movie Frame (24Fs) feature to Auto
allows you to adjust the product’s HDMI output to
24 frames per second for improved picture quality.
You can enjoy the Movie Frame (24Fs) feature only
on a TV supporting this frame rate. You can select
Movie Frame only when the product is in the HDMI
1080i or 1080p output resolution modes.
• Auto : Movie Frame (24Fs) functions work.
• Off : Movie Frame (24Fs) functions are off.
Lets you improve picture quality when viewing DVDs.
• Video : Select for the best picture quality from
concert or TV show DVDs.
Video Conversion
You can convert the incoming composite or
component video signal into a maximum quality of
the connected TV if you output the converted video
via HDMI OUT.
• Bypass : Converts the input video source into
the digital counterpart without changing the
resolution.
✎ NOTE
 A income signal supports only 480i.
English
HW-D7000_XAA_0321.indd 39
39
2011-03-21
2:01:50
Setup
• Large : Select when using large speakers. You
can listen to full range sound.
• Small : Select this when using small speakers.
• None : Select when no speaker is used.
• On (subwoofer) : Select when using the
subwoofer speaker.
• Off (subwoofer) : Select when not using the
subwoofer speaker.
Audio
Speaker Settings
Settings
Speaker Settings
Display
Audio
Size
Network
Level
System
Distance
Language
7.1 CH Connection : Surround Back
Security
Test Tone
|
✎ NOTE
 You can also use the ,,., <, >, ENTER
: Off
General
Support
buttons on the front of your Receiver.
> Move " Enter ' Return
 When the Surround Speaker in set to None,
you can not select Surround Back speaker.
Size
Level
Signal outputs and frequency response from the
speaker will be adjusted according to your
speaker configuration and whether certain
speakers are used or not.
You can adjust the balance and level for each
speaker.
• Each time you press the ▲▼ buttons, Front Center Surround Surround Back Subwoofer will be selected in turn.
Adjusting Front/Center/Surround/Surround
Back/Subwoofer Speaker Level
• You can adjust the volume level in steps from
-10dB ~ +10dB.
• The sound gets louder as you move closer to
+10dB and quieter as you get closer to -10dB.
Settings
Size
Display
Audio
Front
Network
Center
: Small
System
Surround
: Small
Language
Surround Back : Small
Security
Subwoofer
: On
General
Test Tone
: Off
◄
Large |
Support
Settings
Level
Display
Audio
Network
System
Language
> Move " Enter ' Return
Security
General
Support
Front L
Front R
Center
Surround L
Surround R
Surround Back L
Surround Back R
Subwoofer
Test Tone
◄
:
:
:
:
:
:
:
:
0 dB |
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
Off
> Move < Change ' Return
Setting the Speaker
Speaker
Possible Settings
Default
Setting
Front
Large, Small
Small
Center
Large, Small, None
Small
Surround
Large, Small, None
Small
Surround Back Large, Small, None
Small
Subwoofer
On
40
On, Off
English
HW-D7000_XAA_0321.indd 40
2011-03-21
2:01:51
03
If you cannot place the speakers at equal
distances from the listening position, you can
adjust the delay time of the audio signals from the
front, center, surround, surround back and
subwoofer speakers.
• You can set the Speaker Distance between
1ft (0.3m) and 30ft (9.0m).
Settings
Distance
Display
Audio
Network
System
Language
Security
General
Support
Front L
◄
Front R
:
Center
:
Surround L
:
Surround R
:
Surround Back L :
Surround Back R :
Subwoofer
:
Test Tone
:
10(ft) 3.0(m) |
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
10(ft) 3.0(m)
Off
> Move < Change ' Return
7.1 CH Connection
Settings for the surround back speaker differ
depending on the connection method and
installation site of the speaker to be connected.
You must configure the surround back settings
according to the connected speaker before you
listen to music properly.
Settings
Speaker Settings
Display
Audio
Size
Network
Level
• Bi-AMP : Select this if you want to connect the
Bi-Amp compliant speaker to the surround
back port. With this setting, you can enable the
Bi-Amp feature.
✎ NOTE
 Depending on the surround back settings,
the surround back speaker or front height
speaker menus may not be activated or
may differ in the speaker menu: Size, Level,
Distance.
 Depending on your setting, you may not
use different features simultaneously. If
you set Surround Back, for instance, you
cannot use the following features: PL IIz and
Bi-AMP.
Test Tone
Use the Test Tone feature to check the speaker
connections.
Press the ◄, ► buttons to select On.
• A test tone will be sent to Front L Center Front R Surround R Surround Back R
Surround Back L Surround L Subwoofer in order so you can make sure the
speakers are set up correctly.
To stop the test tone, press the ◄, ► buttons to
select Off.
Settings
System
Distance
Language
7.1 CH Connection ◄ Surround Back |
Display
Security
Test Tone
Audio
Size
Network
Level
:
Off
General
Support
Setup
Distance
> Move " Enter ' Return
Speaker Settings
System
Distance
Language
7.1 CH Connection : Surround Back
Security
Test Tone
◄
On
|
General
Support
• Surround Back : Select this if you want to
install the surround back speaker in the default
settings. With this setting, you can enable the
Dolby Pro Logic IIx mode.
• PL IIz : Select this if you want to install the
surround back speaker in the top front corner.
With this setting, you can enable the Dolby Pro
Logic IIz mode.
> Move " Enter ' Return
✎ NOTE
 When HDMI Audio is ON (audio is produced
through TV speakers), the Test Tone
function is not available.
English
HW-D7000_XAA_0321.indd 41
41
2011-03-21
2:01:53
Setup
Musical Room Calibration
By setting the Musical Room Calibration (MRC)
function just once when you relocate or install the
product, you can have the product automatically
recognize the distance between speakers, levels
between channels, and frequency characteristics
to create a 7.1-channel sound field optimized for
your environment.
ASC MIC
VIDEO
AUDIO
✎ NOTE
 Running the Musical Room Calibration
function takes about 3 minutes.
 Make sure there is no disc in the product when
you run the Musical Room Calibration function.
 If the ASC microphone is disconnected during the

PHONES
AUX 1 IN

PHONES
AUDIO
VIDEO
ASC
MIC
AUX
3D
AUDIO
EFFECT
AUDIO
ASSIGN
RETURN
MENU
MEMORY
SELECT
TUNING
MODE
AV
vTuner
HUB
Smart
TONE
CONTROL
SYNC
SOUND
1 IN
ASC
microphone



Musical Room Calibration Mode
You will hear either the Musical Room Calibration
mode or the User Speaker Settings.
• Off: You will hear sound in the Speaker Setting
value.
• On: You will hear sound in the Musical Room
Calibration mode.

Musical Room Calibration setup, the setup will be
canceled.
If the product is connected to external devices or
other components (such as an iPod, AUX, D.IN),
the Musical Room Calibration Setup may not work
properly.
Noise may result in incorrect measurements.
Ensure the room is quiet when you run the
Musical Room Calibration.
Place the microphone in the main listening
position.
Make sure there are no objects between the
speakers and microphone.
Note that the test tones of the speakers may be
loud.
Do not place the microphone behind furniture or
too close to the wall. Otherwise, it can produce an
incorrect test result.
Measurement
1. Plug the ASC microphone into the ASC IN jack.
2. Place the ASC microphone at the listening position.
• Musical Room Calibration will be automatically
set up in the following sequence:
Front L Center Front R Surround
R Surround Back R Surround Back
L Surround L Subwoofer
• Press the RETURN button to cancel the
Musical Room Calibration Setting.
42
English
HW-D7000_XAA_0321.indd 42
2011-03-21
2:01:55
03
Setup
Surround
Set surround sound effect-related functions.
Surround Mode and Input Signal Chart
o = active, – = inactive
Input Signal
O
O
Output Channel
Display Information
SL SBL
Channel Status
C
SUBW
Signal Format
SR SBR
Digital + Dolby Digital
L, C, R, SL, SR ,SBL, SW
O
O
–
O
Digital +Dolby Digital EX L, C, R, SL, SR ,SBL, SBR, SW
O
O
O
O
Digital + Dolby Digital
L, C, R, SL, SR ,SBL, SBR, SW
O
O
O
O
+ ProLogic IIx
Digital + Dolby Digital
L, C, R, SL, SR, H, SW
O
O O (Height)
O
+ ProLogic Iiz
Digital + Dolby Digital
L, C, R, SL, SR ,SBL, SBR, SW
O
O
O
O
Plus
Dolby TrueHD
L, C, R, SL, SR ,SBL, SBR, SW
O
O
O
O
DTS
L, C, R, SL, SR ,SBL, SW
O
O
–
O
O
O
O
O
O
DTS + ProLogic IIx
L, C, R, SL, SR ,SBL, SBR, SW
O
O
O
O (Height)
O
DTS + ProLogic Iiz
L, C, R, SL, SR ,SBL, SBR, SW
O
O
O
O
O
O
O
–
O
O
DTS ES
DTS 96/24
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR ,SBL, SW
O
O
O
O
O
DTS-HD MSTR
L, C, R, SL, SR ,SBL, SBR, SW
O
O
O
O
O
DTS-HD
L, C, R, SL, SR, SBL, SBR, SW
O
O
O
O
O
–
O
O
–
O
O (Height)
–
O
O
O
L, C, R, SL, SR, SBL, SBR, SW
L, C, R, SL, SR, H, SW
L, R, SW
ProLogic IIx
O
O
O
O
O
ProLogic Iiz
O
O
O
O (Height)
O
NEO:6
O
O
O
O
O
SFE
O
O
O
O
O
O
O
O
O
O
–
O
O
–
O
O (Height)
–
O
O
O
O
O
O
O
O
Digtal + LPCM
Digtal + LPCM
Digtal + LPCM
Digtal + LPCM
+ Dolby Digital +
ProLogic IIx
Digtal + LPCM
+ Dolby Digital +
ProLogic Iiz
Digtal + LPCM + DTS
+ NEO:6
Digital + LPCM + LIVE
SURR
Analog
Analog
Analog
Analog + Dolby Digital
+ ProLogic IIx
Analog + Dolby Digital
+ ProLogic Iiz
Analog + DTS NEO:6
Analog + LIVE SURR
Surround
Mode
Dolby Digital
Dolby Digital
Dolby Digital EX
Dolby Digital +
Dolby Digitital EX
ProLogic IIx
Dolby Digital +
ProLogic Iiz
Dolby Digital
Dolby Digital Plus
Plus
Dolby TrueHD
Dolby TrueHD
DTS (5.1-ch)
DTS Surround
DTS Digital +
DTS-ES
ProLogic IIx
DTS Digital +
ProLogic Iiz
DTS 96/24
DTS-ES
DTS 96/24
DTS-HD Master
Audio
DTS-HD
DTS-HD High
Resolution
Multi-Channel
LPCM Multi-Channel
Multi-Channel
Stereo
2-ch PCM
Multi-Channel
Analog Multi-Channel
Multi-Channel
Stereo
ProLogic IIx
Analog 2-ch
L/R
O
O
O
O
O
ProLogic Iiz
O
O
O
O (Height)
O
NEO:6
SFE
O
O
O
O
O
O
O
O
O
O
L/R : front speaker (left/right)
SL/SR : surround speaker (left/right)
SW : subwoofer
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR, H, SW
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR, H, SW
L, R, SW
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR, H, SW
L, C, R, SL, SR ,SBL, SBR, SW
L, C, R, SL, SR ,SBL, SBR, SW
C : center speaker
SBL/SBR : surround back speaker (left/right)
English
HW-D7000_XAA_0321.indd 43
43
2011-03-21
2:01:56
Setup
✎ NOTE
 Channel status displays are dependent on the
speaker configuration.
 SFE mode works with 2-ch signals.
 If Dolby Pro Logic IIz is set to On, Dolby true
HD, Dolby plus, DTS-HD Master Audio, SFE
and NE0:6 will be output 5.1 channel.
• Off : Dolby Digital Surround EX / DTS ES
decoder will not be used for playback.
• On : Dolby Digital or DTS signal will be played
in 6.1 / 7.1 channel using Dolby Digital
Surround EX / DTS ES decoder.
✎ NOTE
 You cannot use DTS-ES without surround
DPL IIx
• Panorama : You can set it On or Off.
(This mode extends the front stereo image to
include the surround speakers for an exciting
"wraparound" effect with side wall imaging.)
• Dimension : You can set from -7 to +7.
(Incrementally adjusts the sound field (DSP)from
the front or surround.)
• Center Width : You can set from 0 to 7.
(This sets the width of the center sound image.
The higher the setting, the less sound comes
from the center speaker.)
Extended Surround (EX/ES)
When surround back speakers are connected,
you can listen to 6.1 or 7.1 multi-channel sound
using the built-in Dolby Digital Surround EX or
DTS ES decoder. This function works when a
Dolby Digital or DTS source is input, and does
not work with L.PCM and Dolby Digital 2 channel
sources.
• Auto : If the unit receives an audio signal that it
can recognize, it will select an optimal decoder
for playback in 6.1/7.1 channels.
If the amplifier does not recognize the audio
signal, it will not play in 6.1/7.1 channel
automatically.
back speakers connected.
DTS Neo:6 Center Image
You can play back 2 channel sound over 6.1
channels when enjoying music or a movie.
• You can set Center Image from 0 to 5.
This parameter adjusts the height of the center
image through the front and center speakers.
“0” is the lowest while “5” is the highest.
✎ NOTE
 NEO:6 mode cannot be used with Dolby
Digital, Dolly Digital Plus, Dolby True HD,
DTS, DTS-HD Master Audio.
 Pro Logic works only for PCM audio signals
with sampling frequencies of 32KHz, 44KHz
or 48KHz.
Crossover Frequency
Select the crossover frequency for the best bass
response in your speakers.
• You can set frequencies 60, 80, 100,120, 150,
180 or 200(Hz).
MP3 Enhancer
This also helps enhance your sound experience
(ex. mp3 music). You can upscale your MP3 level
sound (24 kHz, 8bit) to CD level sound (44.1 kHz,
16bit).
Smart Volume
This will regulate and stabilize the volume level
against a drastic volume change when changing
channels or during a scene transition.
44
English
HW-D7000_XAA_0321.indd 44
2011-03-21
2:01:57
03
Setup
Dual Mono
Digital Output
Dual mono programs have two independent
mono channels.
You can use this function when dual mono
programs are played.
When you use this function, select audio
channels CH1, CH2 or both Channel.
You set the Digital Output to match the
capabilities of the AV device you’ve connected to
the product :
• PCM : Choose if you have connected an HDMI
supported AV device.
• Bitstream (Unprocessed) : Select if you have
connected an HDMI supported AV device with
Dolby TrueHD and DTS-HD Master Audio
decoding capabilities.
• Bitstream (Re-encoded DTS) : Choose if you
have connected an AV device using a Digital
Optical input that can decode DTS.
• Bitstream (Re-encoded Dolby D) : Select if
you don’t have an HDMI supported AV device,
but have an AV device with Dolby Digital
decoding capabilities.
• Ch 1 : Channel 1 is heard only.
• Ch 2 : Channel 2 is heard only.
• Both Channels : Both channels are heard from
front speakers.
HDMI Audio
The audio signals transmitted over the HDMI
Cable can be toggled On/Off.
• Off : Video is transmitted over the HDMI
connection cable only, and audio is output
through your product speakers only.
• On : Both video and audio signals are transmitted
over the HDMI connection cable, and audio is
output through your TV speakers only.
✎ NOTE
 HDMI Audio is automatically down-mixed to
2ch for TV speakers.
Audio Return Channel
You can enjoy TV sound from the Home Theater
speakers by using just one HDMI cable.
• Auto : Listen to TV sound from the Home
Theater speakers if your TV is compatible with
the Audio Return Channel function.
• Off : Turn the Audio Return Channel function
off.
✎ NOTE
 When Anynet+ (HDMI-CEC) is Off, the Audio
Return Channel function is not available.
 Using an ARC (Audio Return Channel)
uncertified HDMI cable may cause a
problem in compatibility.
For more details, please refer to the digital output
selection table. (See page 46)
✎ NOTE
 Digital Output can be activated when HDMI
Audio is ON.
 Be sure to select the correct Digital Output or
you will hear no sound or just loud noise.
 If the HDMI device (AV device, TV) is not
compatible with compressed formats (Dolby
digital, DTS), the audio signal outputs as PCM.
 Regular DVDs do not have BONUSVIEW audio
and Navigation Sound Effects.
 Some Blu-ray Discs do not have BONUSVIEW
audio and Navigation Sound Effects.
 This Digital Output setup does not effect the
analog (L/R) audio or HDMI audio output to
your TV.
It effects the optical and HDMI audio output
when your product is connected to an AV
device.
 If you play MPEG audio soundtracks, the audio
signal outputs as PCM regardless of your
Digital Output selections (PCM or Bitstream).
 ARC function is only available if an ARCcompliant TV is connected.
English
HW-D7000_XAA_0321.indd 45
45
2011-03-21
2:01:57
Setup
Digital Output Selection
Setup
PCM
Bitstream
(Unprocessed)
Bitstream
(Re-encoded
DTS)
Bitstream
(Re-encoded
Dolby D)
HDMI supported HDMI supported HDMI supported HDMI supported
AV device
AV device
AV device
AV device
Connection
PCM
Up to 7.1ch
PCM
DTS re-encoded
Re-encoded
Dolby Digital *
Dolby Digital
Up to 7.1ch
Dolby Digital
DTS re-encoded
Re-encoded
Dolby Digital *
Dolby Digital Plus
Up to 7.1ch
Dolby Digital Plus
DTS re-encoded
Re-encoded
Dolby Digital *
Dolby TrueHD
Up to 7.1ch
Dolby TrueHD
DTS re-encoded
Re-encoded
Dolby Digital *
DTS
Up to 6.1ch
DTS
DTS re-encoded
Re-encoded
Dolby Digital *
DTS-HD HRA
Up to 7.1ch
DTS-HD HRA
DTS re-encoded
Re-encoded
Dolby Digital *
DTS-HD MA
Up to 7.1ch
DTS-HD MA
DTS re-encoded
Re-encoded
Dolby Digital *
Audio Stream on
Blu-ray Disc
Audio Stream
on DVD
PCM
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
Dolby Digital
Up to 5.1ch
Dolby Digital
Dolby Digital
Dolby Digital
DTS
Up to 6.1ch
DTS
DTS
DTS
Decodes the main
feature audio and
BONUSVIEW audio
stream together
into PCM audio and
adds Navigation
Sound Effects.
Outputs only the
main feature audio
stream so that
your AV device can
decode the audio
bitstream.
You will not hear
BONUSVIEW
audio or Navigation
Sound Effects.
Definition for
Blu-ray Disc
Any
Decodes the main
Decodes the main
feature audio and
feature audio and
BONUSVIEW audio BONUSVIEW audio
stream together
stream together into
into PCM audio and PCM audio and adds
adds Navigation
Navigation Sound
Sound Effects, then
Effects, then rere-encodes the
encodes the PCM
PCM audio into DTS audio into Dolby digital
bitstream.
bitstream or PCM.
* If the Source Stream is 2ch, “Re-encoded Dolby D” Setting are not applied. Ouput will be LPCM 2ch.
Blu-ray Discs may include three audio streams :
- Main Feature Audio : The audio soundtrack of
the main feature.
- Navigation Sound Effects : When you choose
some menu navigation, Navigation Sound
Effects may sound. Navigation Sound Effects
are different on each Blu-ray Disc.
- BONUSVIEW audio : An additional
soundtrack such as the director or actor’s
commentary.
46
English
HW-D7000_XAA_0321.indd 46
2011-03-21
2:01:57
03
Setup
Dynamic Range Control
Network Settings
You can listen at low volumes, but still hear dialog
clearly. This is only active if your product detects
a Dolby Digital signal.
• Auto : The Dynamic Range Control will be set
automatically based on the information
provided by the Dolby TrueHD Soundtrack.
• Minimum : This slightly compresses the
dynamic range.
• Standard : This is standard setting for regulate
home use.
• Maximum (Night Mode) : This greatly
compresses the dynamic range and lets you
view movies late at night at low volumes.
To begin setting up the network connection for
your product, follow these steps:
1. In the Home menu, press the ◄► buttons to
select Settings, and then press the ENTER
button.
HDMI Auto Sync
The Receiver can be set to automatically correct
any delay between the video and the audio,
based on the data from the connected TV.
• Auto : Automatically adjust output timing of
audio and video if your TV supports and
automatic lipsync function.
• Off : HDMI Auto Sync is disabled.
Audio Sync
2. Press the ▲▼ buttons to select Network, and
then press the ENTER button.
3. Press the ▲▼ buttons to select Network
Settings, and then press the ENTER button.
4. Press the ▲▼ buttons to select Wired, Wireless
(General), WPS(PBC) or One Foot Connection,
and then press the ENTER button.
5. If you have a wired network, go to Wired Network
below. If you have a wireless network, go to
Wireless Network on pages 48~50.
Wired Network
Setting Up a Wired Connection - Auto
1. Press the ▲▼ buttons to select Wired.
Settings
Network Settings
Display
Audio
Video may fall out of sync with the audio when
the product is connected to a digital TV. If this
occurs, adjust the audio delay time to match the
audio to the video.
• You can set the audio delay time between 0 msec
and 240 msec. Set it to the optimal status.
Network
Before you begin, contact your ISP to find out if
your IP address is static or dynamic. If it is
dynamic, and you are using a wired or wireless
connection, we recommend using the Auto
procedures. If you are using a wireless
connection and your router has the capability,
you can use WPS(PBC) or One Foot Connection.
Network
System
Select a network connection type.
Wired
Language
Wireless
(general)
Security
WPS(PBC)
General
One Foot
Connection
Support
Connect to the network using LAN cable. Please make
sure that the LAN cable is connected.
> Move " Enter ' Return
2. Press the ENTER button.
The Network Status screen appears. The
product connects to the network after the
network connection is verified.
Setting Up a Wired Connection - Manual
If you have a static IP address or the Auto Setting
does not work, you’ll need to set the Network
Settings values manually.
If your IP address is static, you must use the
manual set up procedure for both wired and
wireless connections.
English
HW-D7000_XAA_0321.indd 47
47
2011-03-21
2:01:57
Setup
To view your Network Settings values on most
Windows computers, follow these steps:
1. Right click the Network icon on the bottom
right of the Windows desktop.
11. Press the ENTER button to select OK.
The Network Status screen appears. The
product connects to the network after the
network connection is verified.
2. In the pop-up menu, click Status.
Wireless Network
3. On the dialog that appears, click the Support
tab.
You can setup a wireless network three ways:
• Wireless (General)
• Using WPS(PBC).
• One Foot Connection
Wireless (General) includes both Automatic and
Manual setup procedures.
4. On the Support tab, click the Details button.
The Network settings are displayed.
To enter the Network settings into your product,
follow these steps:
1. Press the ▲▼ buttons to select Wired, and
then press the ENTER button.
2. Press the ◄► buttons to select IP Settings,
and then press the ENTER button.
Settings
IP Settings
Display
Audio
IP Mode
Network
System
Language
Security
Manual
0 . 0 . 0 . 0
0 . 0 . 0 . 0
0 . 0 . 0 . 0
IP Address
Subnet Mask
Gateway
DNS Mode
Manual
0 . 0 . 0 . 0
DNS Server
General
OK
Support
m Move
Number " Enter ' Return
3.
Press the ENTER button to select IP Mode.
4.
Press the ▲▼ buttons to select Manual,
and then press the ENTER button.
5.
Press the ▼ button to go to the first entry
field (IP Address).
Setting Up the Wireless Network Connection
- Auto
Most wireless networks have an optional security
system that requires devices that access the
network to transmit an encrypted security code
called an Access or Security Key. The Security
Key is based on a Pass Phrase, typically a word
or a series of letters and numbers of a specified
length you were asked to enter when you set up
security for your wireless network. If you use this
method of setting up the network connection,
and have a Security Key for your wireless
network, you will have to enter the Pass Phrase
during the Auto setup process.
1. Press the ▲▼ buttons to select Wireless
(General).
Settings
Network Settings
Display
Select a network connection type.
Audio
Network
Wired
System
6.
Use the number buttons on your remote to
enter numbers.
7.
When done with each field, press the ►
button to move successively to the next field.
You can also use the other arrow buttons to
move up, down, and back.
8.
Enter the IP Address, Subnet Mask, and
Gateway values.
9.
Press the ▼ button to go to DNS Mode.
10. Press the ▼ button to go to the first DNS
entry field. Enter the numbers as above.
48
Wireless
Language (general)
Security WPS(PBC)
General One Foot
Support Connection
Set up wireless network by selecting your Wireless
Router. You may need to enter security key depending
on the setting of the Wireless Router.
> Move " Enter ' Return
2. Press the ENTER button.
When done, it displays a list of the available
networks.
3. Press the ▲▼ buttons to select the desired
network, and then press the ENTER button.
The Security screen appears.
English
HW-D7000_XAA_0321.indd 48
2011-03-21
2:01:58
03
Settings
Display
Audio
Network Settings
Enter security key.
0 entered
To enter the Network settings into your product,
follow these steps:
Setup
4. On the Security screen, enter your network’s
Pass Phrase. Enter numbers directly using
your remote control.
To select a letter, press the ▲▼◄► buttons
to move the cursor, then press the ENTER
button.
1. Follow Steps 1 through 5 in the ‘Setting Up
the Wireless Network Connection - Auto’
procedure.
2. When done, press the ▲▼◄► buttons to
move the cursor to Done, and then press the
ENTER button. The Network Status screen
appears.
Network
System
Language
Security
General
Support
a
b
f
1
2
3
g
h
i
j
k
l
4
5
6
m
n
o
p
q
r
7
8
9
s
t
u
v
w
x
y
z
0
*
Delete
a/A
c
d
e
Space
Settings
IP Settings
Display
Audio
Done
Network
a Previous m Move " Enter ' Return
System
Language
Security
✎ NOTE
IP Mode
Manual
0 . 0 . 0 . 0
0 . 0 . 0 . 0
0 . 0 . 0 . 0
IP Address
Subnet Mask
Gateway
DNS Mode
Manual
0 . 0 . 0 . 0
DNS Server
General
OK
Support
> Move " Enter ' Return
 You should be able to find the Pass Phrase on
one of the set up screens you used to set up
your router or modem.
3.
On the Network Status screen, select
Cancel, and then press Enter.
4.
Press the ◄► buttons to select IP Settings,
and then press the ENTER button.
5.
Press the ENTER button to select IP Mode.
6.
Press the ▲▼ buttons to select Manual,
and then press the ENTER button.
Setting Up the Wireless Network Connection
- Manual
7.
Press the ▼ button to go to the first entry
field (IP Address).
If the Auto Setting does not work, you need to
enter the Network settings values manually.
8.
Use the number buttons to enter numbers.
9.
When done with each field, press the ►
button to move successively to the next field.
You can also use the other arrow buttons to
move up, down, and back.
5. When done, press the ▲▼◄► buttons to
move the cursor to Done, and then press the
ENTER button.
The Network Status screen appears. The
product connects to the network after the
network connection is verified.
To view the Network Settings values on most
Windows computers, follow these steps:
1. Right click the Network icon on the bottom
right of the screen.
2. In the pop-up menu, click Status.
3. On the dialog that appears, click the Support
tab.
4. On the Support tab, click the Details button.
The Network settings are displayed.
10. Enter the IP Address, Subnet Mask, and
Gateway values.
11. Press the ▼ to go to DNS Mode.
12. Press the ▼ button to go to the first DNS
entry field. Enter the numbers as above.
13. The Network Status screen appears. The
product connects to the network after the
network connection is verified.
English
HW-D7000_XAA_0321.indd 49
49
2011-03-21
2:02:00
Setup
WPS(PBC)
2. Press the ENTER button.
The easiest way to set up the wireless network
connection is using the WPS(PBC) function or the
One Foot Connection function.
If your wireless router has a WPS(PBC) button,
follow these steps:
1. Press the ▲▼ buttons to select WPS(PBC).
Settings
Network Settings
Display
Select a network connection type.
Audio
Network
3. Place the Samsung Wireless Router within
25 cm (10 inches) of your product to
connect.
4. Wait until the connection is automatically
established.
Network Status
Check whether a connection to the network and
the Internet have been established.
Wired
System
Settings
Wireless
Language (general)
Security WPS(PBC)
General One Foot
Support Connection
Connect to the Wireless Router easily by pressing the
WPS(PBC) button. Choose this if your Wireless Router
supports Push Button Configuration(PBC).
Audio
Network
> Move " Enter ' Return
Network Status
Display
KT_WLAN
System
MAC Address
IP Address
Subnet Mask
Gateway
DNS Server
XX:XX:XX:XX:XX:XX
0.0.0.0
0.0.0.0
0.0.0.0
0.0.0.0
Internet is connected successfully.
Language
If you have a problem using any Internet services, contact your Internet service
provider.
Security
General
2. Press the ENTER button.
3. Press the WPS(PBC) button on your router
within two minutes. Your product displays
the Network Selection Screen, and
automatically acquires all the network
settings values it needs and connects to your
network. When it is done, it displays an OK
button. Press the ENTER button on your
remote.
One Foot Connection
You can set up the wireless connection
automatically if you have a Samsung Wireless
Router which supports One Foot Connection. To
connect using the One Foot Connection function,
follow these steps:
1. Press the ▲▼ buttons to select One Foot
Connection.
Settings
Network Settings
Display
Select a network connection type.
Audio
Network
Wired
IP Settings
Retry
OK
< Move " Enter ' Return
BD-LIVE Internet Connection
Set to allow or prohibit an Internet connection
when you use the BD-LIVE service.
• Allow (All) : The Internet connection is allowed
for all BD-LIVE contents.
• Allow (Valid Only) : The Internet connection is
allowed only for BD-LIVE contents containing a
valid certificate.
• Prohibit : No Internet connection is allowed for
any BD-LIVE content.
✎ NOTE
 What is a valid certificate?
When the product uses BD-LIVE to send the
disc data and a request to the server to certify
the disc, the server uses the transmitted data
to check if the disc is valid and sends the
certificate back to the product.
 The Internet connection may be restricted
System
Wireless
Language (general)
Security WPS(PBC)
General One Foot
Support Connection
Support Network Settings
Connect to your wireless network automatically if your
Wireless Router supports One Foot Connection. Select
this connection type after placing the Wireless Router
within 10 inches(25cm) of product.
while you are using BD-LIVE contents.
> Move " Enter ' Return
50
English
HW-D7000_XAA_0321.indd 50
2011-03-21
2:02:01
03
Initial Settings
By using the Initial Settings function, you can set
the language, Network Settings, etc.
For more information about the Initial Settings
function, refer to the Initial Settings section of this
user manual. (See page 34)
Anynet+ (HDMI-CEC)
Anynet+ is a convenient function that offers linked
operations with other Samsung products that
have the Anynet+ feature.
To operate this function, connect this product to
a Samsung TV with an HDMI cable.
With Anynet+ on, you can operate this product
using a Samsung TV remote control and start
disc playback simply by pressing the PLAY (►)
button on the TV’s remote control.
For more information, please see the TV user
manual.
• Off : Anynet+ functions will not work.
• On : Anynet+ functions will work.
✎ NOTE
 This function is not available if the HDMI cable
does not support CEC.
 If your Samsung TV has an Anynet+ logo, then
it supports the Anynet+ function.
 Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
• Available Size : Available memory in the
device.
• Delete BD Data : Delete all BD data in the
storage.
• Select Device : Change location of desired
memory to store BD data.
✎ NOTE
 In the external memory mode, disc playback
may be stopped if you disconnect the USB
device in the middle of playback.
 Only those USB devices formatted in the FAT
file system (DOS 8.3 volume label) are
supported. We recommend you use USB
devices that support USB 2.0 protocol with 4
MB/sec or faster read/write speed.
 The Resume Play function may not work after
you format the storage device.
 The total memory available to BD Data
Management may differ, depending on the
conditions.
Input Selection
Set the default port of DIGITAL AUDIO IN for
each sources.
• SAT : Select the desired input port for SAT
source.
• GAME : Select the desired input port for GAME
source.
• CD : Select the desired input port for CD
source.
BD Data Management
Time Zone
Lets you manage the downloaded contents you
accessed through a Blu-ray Disc that supports
the BD-LIVE service and stored on memory
device.
You can specify the time zone that is applicable
to your area.
Settings
Display
You can check the device’s information including
the storage size, delete the BD data, or change
the memory device.
Setup
System
Time Zone
Audio
Network
System
Language
Security
BD Data Management Screen Information :
• Current Device : Display the selected device.
• Total Size : Total memory size of the device.
General
Support
GMT + 00:00
London, Lisbon, Casablanca
< Change " Save ' Return
English
HW-D7000_XAA_0321.indd 51
51
2011-03-21
2:02:04
Setup
DivX® Video On Demand
Shows the registration code authorized for the
product. If you connect to the DivX web site and
register using that code, you can download the
VOD registration file. If you activate the VOD
registration using My Contents, the registration is
completed.
✎ NOTE
 For more information about DivX(R) VOD,
visit "http://vod.divx.com".
Reset
All settings will revert to the default except for the
network and Smart Hub settings. You need enter
the password for this function.
✎ NOTE
 The default password is 0000.
Language
You can select the language you prefer for the
Home menu, disc menu, etc.
• On-Screen Menu : Select the language for the
on-screen displays.
• Disc Menu : Select the language for the disc
menu displays.
• Audio : Select the language for disc audio.
• Subtitle : Select the language for disc subtitles.
✎ NOTE
After you have set your password, select an age
rating you want to set for the BD Parental Rating
and a rating level you want to set for the DVD
Parental Rating. The product will only play Blu-ray
discs rated at or below the age rating and DVD
discs rated below the numeric rating unless the
password is entered.
Larger numbers indicate more mature content.
BD Parental Rating
This will prohibit playback of Blu-ray disc rated
above Parental Rating.
DVD Parental Rating
Prevent playback of DVD discs with specific
numerical ratings unless a password is entered.
Change Password
Change the 4-digit password used to access
security functions.
If you forgot your password
1. Remove the disc.
2. Press and hold the STOP () button on the
front panel for 5 seconds or more.
All settings will revert to the factory settings.
✎ NOTE
 When the factory default settings are restored,
all the user stored BD data will be deleted.
 The selected language will only appear if
it is supported on the disc.
Security
This function works in conjunction with Blu-ray
and DVD discs that have been assigned an age
rating or numeric rating that indicates the maturity
level of the content. These numbers help you
control the types of Blu-ray and/DVD discs that
your family can watch.
When you access this function for the first time,
the password setup screen appears. Enter a
desired 4-digit password using the number
buttons. (The default password is 0000.)
52
General
Front Display
Change the brightness of the front panel.
• Auto : Dim during playback.
• Dim : Dim the display window.
• Bright : Brighten the display window.
✎ NOTE
 You cannot change the brighness of the
Power button.
English
HW-D7000_XAA_0321.indd 52
2011-03-21
2:02:05
03
The four methods are explained below.
The Network Remote Control function lets you
control your Blu-ray Home Theater from a remote
device such as a smart phone through a wireless
connection to your local area network.
By Internet
To use the Network Remote Control function, follow
these steps:
1. Select On in the Network Remote Control
menu.
2. Install the Samsung network remote control
application to control your product on your
compatible portable device.
3. Make sure your portable device and your
product are connected to the same wireless
router.
4. Start the application on your portable device.
The application should find your product and
display it on a list.
5. Select the product.
6. If this is the first time you are using the
function, it will ask you to allow or deny
remote control of the product. Select Allow.
7. Follow the instructions that came with the
application to control the product.
Setup
Network Remote Control
To upgrade by Internet, follow these steps:
1. Select By Internet, and then press the
ENTER button. The Connecting to Server
message appears.
2. If there is a download available, the
Download pop-up appears with a progress
bar and the download starts.
3. When the download is complete, the
Upgrade Query window appears with three
choices: Upgrade Now, Upgrade Later, or
Don’t Upgrade.
4. If you select Upgrade Now, the product
upgrades the software, turns off, and then
turns on automatically.
5. If you do not make a selection in one minute
or select Upgrade Later, the product stores
the new upgrade software. You can upgrade
the software later using the By Downloaded
function.
6. If you select Don’t Upgrade, the product
cancels the upgrade.
✎ NOTE
 Your product must be connected to the
Support
Software Upgrade
The Software Upgrade menu allows you to
upgrade the product’s software for performance
improvements or additional services. You can
upgrade in four ways:
•
•
•
•
By Internet
By USB
By Disc
By Downloaded (File)
Internet to use the By Internet function.
 The upgrade is complete when the product
turns off, and then turns on again by itself.
 Never turn the product off or back on
manually during the update process.
 Samsung Electronics shall take no legal
responsibility for product malfunction
caused by an unstable Internet connection
or consumer negligence during a software
upgrade.
 If you want to cancel the upgrade while the
upgrade software is downloading, press the
ENTER button.
English
HW-D7000_XAA_0321.indd 53
53
2011-03-21
2:02:05
Setup
By USB
To upgrade by USB, follow these steps:
1. Visit www.samsung.com/bluraysupport
2. Download the latest USB software upgrade
zip archive to your computer.
3. Unzip the zip archive to your computer. You
should have a single folder with the same
name as the zip file.
4. Copy the folder to a USB flash drive.
5. Make sure the disc tray is empty, and then
insert the USB flash drive into the USB port
of the product.
6. In the product’s menu, go to Settings >
Support > Software Upgrade.
7. Select By USB.
✎ NOTE
 The disc tray must be empty when you
upgrade the software using the USB Host
jack.
 When the software upgrade is done, check
the software details in the software Upgrade
menu.
 Do not turn off the product during the
software upgrade. It may cause the product
to malfunction.
 Software upgrades using the USB Host jack
must be performed with a USB memory
flash stick only.
By Disc
To upgrade by Disc, follow these steps:
1. Visit www.samsung.com/bluraysupport.
2. Download the latest disc software upgrade
zip archive to your computer.
3. Unzip the zip archive to your computer. You
should have a single folder with the same
name as the zip file.
7. In the product’s menu, go to Settings >
Support > Software upgrade.
8. Select By Disc.
✎ NOTE
 When the system upgrade is done, check the
software details in the software Upgrade menu.
 Do not turn off the product during the Software
Upgrade. It may cause the product malfunction.
By Downloaded
The By Downloaded option lets you upgrade using
a file the product downloaded earlier but you
decided not to install immediately or a file
downloaded by the product in Standby Mode (See
Download in Standby Mode below).
To upgrade By Downloaded, follow these steps:
1. If upgrade software has been downloaded,
you will see the software version number to
the right of By Downloaded.
2. Select By Downloaded, and then press the
ENTER button.
3. The product displays a message asking if
you want to upgrade. Select Yes. The
product begins the upgrade.
4. When the update is complete, the product
turns off automatically, and then turns on.
✎ NOTE
 When the system upgrade is done, check the
software details in the software Upgrade
menu.
 Do not turn off the product during the software
Upgrade. It may cause the product to
malfunction.
 To use the By Downloaded function, your
product must be connected to the Internet.
4. Write the folder onto a disc. We recommend
a CD-R or DVD-R.
5. Finalize the disc before you remove it from
your computer.
6. Insert the disc into product.
54
English
HW-D7000_XAA_0321.indd 54
2011-03-21
2:02:06
03
Setup
Download in Standby Mode
You can set the Download in Standby Mode
function so that the product downloads new
upgrade software when it is in Standby mode. In
Standby mode, the product is off, but its Internet
connection is active. This allows the product to
download upgrade software automatically, when
you are not using it.
To set Download in Standby Mode, follow these
steps:
1. Press the ▲▼ buttons to select Download
in Standby Mode, and then press the
ENTER button.
2. Select On or Off.
• Off : If you select Off, the product will notify
you with a pop up message when new
upgrade software is available.
• On : If you select On, the product will
automatically download new upgrade
software when it is in Standby mode with
the power off. If it downloads new upgrade
software, the product will ask you if you
want to install it when you turn the product
on.
✎ NOTE
 To use the Download in Standby Mode
function, your product must be connected to
the Internet.
Contact Samsung
Provides contact information for assistance with
your product.
English
HW-D7000_XAA_0321.indd 55
55
2011-03-21
2:02:06
Basic Functions
• Audio CD (CD-DA)
Playing a Disc
track 1
track 2
track 3
track 4
track 5
Playback
1. Insert a disc into the disc slot with the disc's
label facing up.
2. Press the PLAY (►) button.
folder (group) 1
file 1
file 2
Playback related buttons
PLAY ( ►)
Starts playback.
STOP (  )
Stops playback.
• If you press the button
once : The stop position is
memorized.
• If you press the button twice
: The stop position is not
memorized.
PAUSE (  )
• MP3, WMA, DivX, MKV and MP4
folder (group) 2
file 2
file 3
Playing a 2D video in 3D mode
hZ
You can enjoy an ordinary 2D video in
3D mode.
✎ NOTE
Pauses playback.
 If you move to the Home or Smart
✎ NOTE
Hub Home menu in 3D mode, it will switch
to 2D automatically.
 For some discs, the product may not
memorize the stop positon when you press the
STOP (  ) button.
 Video files with high bit rates of 20Mbps or
more strain the product’s capabilities and
may stop playing during play back.
Using the Disc menu/Title menu/
Popup menu
Using the Disc Menu
hZ
Disc Structure
The content of discs are usually divided as shown
below.
• Blu-ray Disc, DVD-VIDEO
title 1
chapter 1 chapter 2
file 1
chapter 1
title 2
chapter 2
chapter 3
1. During playback, press the DISC
MENU button on the remote
control.
2. Press the ▲▼◄ ► buttons to make
a selection, and then press the
ENTER button.
DISC MENU
✎ NOTE
 Depending on the disc, the menu items may
differ and this menu may not be available.
56
English
HW-D7000_XAA_0321.indd 56
2011-03-21
2:02:06
04
Using the Search and Skip Functions
Z
1. During playback, press the TITLE
MENU button on the remote
control.
2. Press the ▲▼◄ ► buttons to
make the desired selection, then
press the ENTER button.
TITLE MENU
POPUP
Searching for a Desired Scene
hzZyx
✎ NOTE
 Depending on the disc, the menu items may
differ and this menu may not be available.
 The Title Menu will only be displayed if there
are at least two titles on the disc.
Using the Popup Menu
h
1. During playback, press the POPUP
button on the remote control.
During playback, you can search quickly through
a chapter or track, and use the skip function to
jump to the next selection.
TITLE MENU
• During playback, press the SEARCH ()
button.
Each time you press the SEARCH ()
button, the playback speed will change as
follows.
BD-ROM,
BD-RE/-R,
DVD-RW/-R,
DVD+RW/+R,
DVD-VIDEO
DivX, MKV, MP4
POPUP
2. Press the ▲▼◄ ► buttons or
ENTER button to select the
desired menu.
)1)2)3
) 4 ) 5  ) 6  ) 7
(1(2(3
( 4 ( 5  ( 6  ( 7
)1)2)3
(1(2(3
• To return to normal speed playback, press the
PLAY (►) button.
✎ NOTE
✎ NOTE
 Depending on the disc, the menu items may
differ and this menu may not be available.
Playing the Title List
z
1. During playback, press the DISC
MENU or TITLE MENU button.
DISC MENU
2. Press the ▲▼ buttons to select
an entry you want to play from
Title List, then press the ENTER
button.
TITLE MENU
 The Receiver does not play sound in search
mode.
 If you press the  or  button too quickly
this product might think you are just holding
the button down. This will lead to improper
operation. Be sure to not press these buttons
too rapidly.
Skipping Chapters
POPUP
hzZyx
• During playback, press the SKIP (#$)
button.
If you press the SKIP ($) button, the disc
moves to the next chapter.
If you press the SKIP (#) button, the disc
moves to the beginning of the chapter. One
more press makes the disc move to the
beginning of the previous chapter.
English
HW-D7000_XAA_0321.indd 57
Basic Functions
Using the Title Menu
57
2011-03-21
2:02:07
Basic Functions
Slow Motion Play/Step Motion Play
Repeat
> Off
Slow Motion Play
hzZyx
• In pause (  ) mode, press the SEARCH ()
button.
If you press the SEARCH () button, the
playback speed is reduced to
* 1/8 * 1/4 * 1/2
• To return to normal speed playback, press the
PLAY (► ) button.
✎ NOTE
 The product does not play sound in slow
3. To return to normal play, press the REPEAT
button again.
4. Press the ▲▼ buttons to select Off, then
press the ENTER button.
✎ NOTE
 Depending on the disc, the Repeat function
may not be available.
Repeat the Section
mode.
 Slow motion operates only in the forward
direction.
hzZy
REPEAT
1. During playback, press the REPEAT
button on the remote control.
Step Motion Play
hzZyx
• In pause mode, press the PAUSE (  ) button.
Each time the PAUSE (  ) button is pressed, a
new frame will be appear.
• To return to normal speed playback, press the
PLAY ( ► ) button.
✎ NOTE
2. Press the ▲▼ buttons to select
REPEAT A-B.
Repeat
> Repeat A-B : Off
" Mark A
 The product does not play sound in step
3. Press the ENTER button at the point where
you want repeat play to start (A).
 Step motion operates only in the forward
4. Press the ENTER button at the point where
you want repeat play to stop (B).
mode.
direction.
5. To return to normal play, press the REPEAT
button again.
Repeat Playback
6. Press the ENTER button.
Repeat the Title or Chapter
✎ NOTE
hzZy
elapsed, a prohibition message will appear.
 Depending on the disc, the Repeat function
Repeat the disc title or chapter.
1. During playback, press the REPEAT
button on the remote control.
 If you set point (B) before 5 seconds has
REPEAT
may not be available.
2. Press the ▲▼ buttons to select
Chapter or Title, then press the
ENTER button.
58
English
HW-D7000_XAA_0321.indd 58
2011-03-21
2:02:09
04
During playback, you can operate the
disc menu by pressing the TOOLS
button.
TOOLS
• TOOLS Menu Screen
Tools
Title Search
Chapter Search
Time Search
Picture Settings
Audio
User EQ
Subtitle
Angle
1/2
:
1/20
: 00:00:13/01:34:37
:
Normal
: 1/4 ENG Multi CH
:
:
audio modes will be also displayed if the Bluray Disc has a BONUSVIEW section.
Use the ◄► button to switch between
primary and secondary audio modes.
 The languages available depend on the
languages that are encoded on the disc. This
function or certain languages may not be
available.
 Some Blu-ray Discs may allow you to select
either the multi-channel LPCM or Dolby digital
audio soundtrack in English.
Basic Functions
 Information about the primary / secondary
Using the TOOLS button
0/7 Off
1/1
< Change " Enter ' Return
Selecting the Subtitle Language
hZx
✎ NOTE
▪ Depending on the disc, the TOOLS menu
may differ.
Moving to a Desired Scene Directly
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Subtitle.
3. Press the ◄► buttons to select the desired
subtitle language.
NOTE
hzZy ✎ Depending on the Blu-ray Disc / DVD, you may
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Title
Search, Chapter Search or Time Search.
3. Enter the desired Title, Chapter or Playing
Time using the number buttons, then press
the ENTER button.
Selecting the Audio Language
hzZx
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Audio.
3. Press the ENTER button.




be able to change the subtitle language in the
Disc Menu.
Press the DISC MENU button.
The subtitle languages available depend on the
subtitle languages encoded on the disc. This
function or certain languages may not be
available on all Blu-ray Discs/DVDs.
Information about the primary / secondary
subtitle modes will also be displayed if the Bluray Disc has a BONUSVIEW section.
This function changes both the primary and
secondary subtitles at the same time.
The total number of subtitles is the sum of the
primary and secondary subtitles.
4. Press the ▲▼ buttons to select the audio
language you want.
✎ NOTE
 The ◄► indicator will not be displayed on the
screen if the BONUSVIEW section does not
contain any BONUSVIEW audio settings.
English
HW-D7000_XAA_0321.indd 59
59
2011-03-21
2:02:13
Basic Functions
Caption Function
x
• You must have some experience with video
extraction and editing in order to use this
feature properly.
• To use the caption function, save the caption
file (*.smi) with the same file name as that of the
DivX media file (*.avi) within the same folder.
Example. Root Samsung_007CD1.avi
Samsung_007CD1.smi
• You can use up to 60 alphanumeric characters or 30
East Asian characters (2 byte characters such as
Korean and Chinese) for the file name.
Changing the Camera Angle
hZ
• User : The user can adjust the Sharpness,
Noise reduction, Contrast, Brightness,
Color, Tint function respectively.
✎ NOTE
 If the system is connected to a BD Wisecompliant TV that has set BD Wise to On, the
picture setting menu will not appear.
Setting the BONUSVIEW
h
The BONUSVIEW feature allows you to view
additional content (such as commentaries) in a
small screen window while the movie is playing.
This function is only available if the disc has the
Bonusview feature.
When a Blu-ray Disc/DVD contains multiple
angles of a particular scene, you can use the
ANGLE function.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Angle.
3. Press the ◄► buttons to select the desired
Angle.
Selecting the Picture Settings
hzZy
This function enables you to adjust video quality.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Picture
Settings, then press the ENTER button.
3. Press the ◄► buttons to select the desired
Mode, then press the ENTER button.
• Dynamic : Choose this setting to increase
Sharpness.
• Normal : Choose this setting for most
viewing applications.
• Movie : This is the best setting for watching
movies.
Primary a audio/video
Secondary a audio/video
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select BONUSVIEW
Video or BONUSVIEW Audio.
3. Press the ◄► buttons to select the desired
bonusview.
✎ NOTE
 If you switch from BONUSVIEW Video,
BONUSVIEW Audio will change automatically
in accordance with BONUSVIEW Video.
Tools
BONUSVIEW Video
Off
BONUSVIEW Audio :
0/1 Off
Picture Settings
< Change " Enter
60
English
HW-D7000_XAA_0321.indd 60
2011-03-21
2:02:14
04
7
ENTER button : Plays the selected track.
8
► button : During playback, moves to the next
page in the Music List or moves to the next track
in the Playlist.
◄ button : During playback, moves to the
previous page in the Music List or moves to the
previous track in the Playlist.
3
9
STOP button : Stops a track.
0
$ button : Plays the next track.
!
# button : Plays the previous track.
If you press this button after three seconds of
playback in the Playlist, the current track will be
replayed from the beginning. But, if you press this
button within three seconds after playback starts
in the Playlist, the previous track will be played.
@
NUMBER button : During the Playlist playback,
press the desired track number. The selected
track will be played.
ow
Buttons on the Remote Control
used for Music Playback
1
2
4
@
!
5
6
SLEEP
TONE
9
7
8
S.DIRECT
AUDIO ASSIGN
FULL
SCREEN
0
REPEAT
0
1
2
3
9
4
TOOLS
8
INFO
Basic Functions
Listening to Music
5
7
RETURN
EXIT
iPod SYNC
TUNER
MEMORY
A
B
C
D
SMART
SEARCH
vTuner
2D ĺ 3D
MO/ST
6
HUB
1
REPEAT button : Selects the play mode in the
Playlist.
2
SEARCH buttons :
Audio CD (CD-DA) - Fast Play.
MP3 - Jump Play. (10 seconds)
3
PAUSE button : Pauses playback.
4
PLAY button : Plays the currently selected track.
5
▲▼ buttons : Selects a track in the Music List
or Playlist.
6
YELLOW (C) button : Select or deselect a track
in the music list.
English
HW-D7000_XAA_0321.indd 61
61
2011-03-21
2:02:15
Basic Functions
Playing an Audio CD (CD-DA)/MP3
Repeat an Audio CD (CD-DA)/MP3
1. Insert an Audio CD (CD-DA) or an MP3 Disc
into the disc slot.
• For an Audio CD (CD-DA), the first track will
be played automatically.
• For an MP3 disc, press the ◄► buttons to
select Music, then press the ENTER
button.
1. During the Playlist playback, press
the REPEAT button.
Audio CD (CD-DA)/MP3 Screen Elements
1
2
3
REPEAT
2. Select the desired play mode by
pressing the REPEAT button repeatedly.
Off
( ) One
Song
(
) All
Music
Tracks on a disc are played
Audio CD
in the order in which they
(CD-DA)/MP3
were recorded on the disc.
Audio CD
Current track is repeated.
(CD-DA)/MP3
Audio CD
All tracks are repeated.
(CD-DA)/MP3
1/13
TRACK 001
✎ NOTE
TRACK 001
00:43
 During playback, press the TOOLS button and
TRACK 002
03:56
set Shuffle Mode to On. You can play the
tracks in a random order.
TRACK 003
7
6
04:41
TRACK 004
+
04:02
00:13 / 00:43
Audio CD
" Enter < Pages
5
Tools ' Return
4
Playlist
1. Insert an Audio CD (CD-DA) or an MP3 Disc
into the disc slot.
• For an Audio CD (CD-DA), the first track will
be played automatically.
1
Displays the music information.
2
Displays the playlist.
3
Shows the current track/total tracks.
4
Displays buttons available.
5
Shows the current play time/total play time.
3. Press the YELLOW (C) button to switch to
Edit Mode.
6
Displays the current playback status.
7
Displays the repeated playback status.
4. Press ▲▼◄► to select a desired track, and
then press ENTER. Repeat this procedure to
select additional tracks.
• For an MP3 disc, press the ◄► buttons to
select Music, then press the ENTER
button.
2. To move to the Music List, press the STOP ()
or RETURN button.
The Music List screen is displayed.
• The selected file will be checked.
2. Press the ▲▼ buttons to select the track
you want to play, and then press the ENTER
button.
62
• To cancel your selection, press ENTER
again to uncheck the track.
English
HW-D7000_XAA_0321.indd 62
2011-03-21
2:02:16
04
Sound Mode
1/2 Page
Selected Items : 3
TRACK 001
TRACK 002
00:43
03:56
TRACK 003
TRACK 004
04:41
04:02
TRACK 005
TRACK 006
03:43
03:40
TRACK 007
TRACK 008
04:06
03:52
Close Edit Mode ( ) Page
Tools
SFE (Sound Field Effect) MODE
You can set the SFE mode best suited
for the type of music you are listening
to.
" Select ' Return
5. When done, press the TOOLS button.
6. To play the selected track(s), select Play
Selected in the Tools menu, and then press
ENTER.
SFE MODE
Basic Functions
Audio CD | Music
Press the SFE MODE button
repetatively,
STEREO  HALL 1 HALL 2  J.CLUB 
CHURCH  ROCK  CLASSIC  LIVE 
GAME  MOVIE  CONCERT  STADIUM
will be selected in turn.
Dolby Pro Logic II Mode
Music
1/3
TRACK 001
TRACK 001
00:43
TRACK 002
You can select the desired Dolby Pro
Logic II audio mode.
Press the
03:56
PL II button.
TRACK 003
04:41
+
Setting the speakers with PL IIz
00:13 / 00:43
Audio CD
" Enter
Tools
' Return
7. To return to the Edit Mode, press STOP or
RETURN.
8. To exit Edit Mode, press the YELLOW (C)
button.
1. Set the 7.1CH Connection settings to "PL
IIz". (For further details, refer to page 41.)
2. Press the
PL II button of the remote
control until "HEIGHT” or “PL OFF”
appears on the display. Set to “HEIGHT”
to enable sound reproduction from front
center/height speakers.
✎ NOTE
HEIGHT
You can listen to a 2CH sound source
in 7.1CH surround sound with all
speakers active.
- A specific speaker(s) may not be
output depending on the input
signal.
PL OFF
Select this option to listen through the
front left/right speakers and the
subwoofer only.
 You can create a playlist with up to 99 tracks
on Audio CD (CD-DA).
English
HW-D7000_XAA_0321.indd 63
63
2011-03-21
2:02:17
Basic Functions
Setting the speakers with DPL IIx
 The models below support audio sync
1. Set the 7.1CH Connection settings to
"Surround Back". (For further details, refer to
page 41.)
settings. Press iPod SYNC on the remote
control to change audio delay.
 Supported Models : classic/3G nano/4G
nano/120GB classic/160GB Classic/5G nano
PL II button of the remote
2. Press the
control until the desired setting is
displayed. Once selected with the desired
mode, sound will be heard through the
surround speakers.
MOVIE
Adds realism to the movie
soundtrack.
MUSIC
When listening to music, you can
experience sound effects as if you
are listening to the actual
performance.
GAME
You can hear like game sound.
MATRIX
PL
PL OFF
You will hear multi channel
surround sound.
You can listen to a 2CH sound
source in 5.1CH surround sound
with all speakers active.
- A specific speaker(s) may not be
output depending on the input
signal.
PL mode will be off.
B
If the video signal does not synchronize properly
with the audio signal, press iPod SYNC on the
remote control to correct the synchronization.
✎ NOTE
 Before you can play the video files in the iPod
player, you must connect the Audio/Video
terminals of the TV to the home theater using the
Composite (A/V) cable.
64
You can enjoy more natural and vivid
surround sound with enriched tones by
adjusting the depth of sound using the
level options.
3D SOUND OFF  3D SOUND HIGH
 3D SOUND MEDIUM  3D SOUND LOW
✎ NOTE
 3D Sound is not available in FM mode.
Using the SHIFT button
ENTER, ▲▼◄►, S.DIRECT, TONE, SLEEP
and AUDIO ASSIGN button will operate, after
pressing the SHIFT button.
✎ NOTE
 ENTER, ▲▼, and ◄► buttons are active
even when you don't press the SHIFT button.
TONE
iPod SYNC
If you insert your iPod player into the
iPod Dock that has already been
connected to the system, you can play
the video files in your iPod player
through the connected TV.
3D Sound
TONE
After pressing the SHIFT button, and
then Press the TONE button repeatedly
to select the option you want.
You can adjust the each value by
pressing the ▲▼ buttons.
9
• BASS : -6dB ~ +6dB
• TREBLE : -6dB ~ +6dB
• TONE : ON, OFF
✎ NOTE
 The Tone Control function can be applied to
all channels except for the subwoofer.
 If it is set to Tone Off, the Tone Control
function will be disabled.
English
HW-D7000_XAA_0321.indd 64
2011-03-21
2:02:20
04
You can listen to sound in 2 channel
analog , Dolby Digital or DTS using this
unit.
Playing back a Picture
G
AUDIO ASSIGN
0
Viewing Photo Files
Each time you press this button, the
input mode changes as follows:
For SAT function
SAT HDMI1  SAT OPTIC1  SAT ANALOG
For GAME function
GAME HDMI2  GAME OPTIC2  GAME
ANALOG
For TV function
TV OPTIC3(TV ARC)  TV ANALOG
Basic Functions
AUDIO ASSIGN
1. Connect a USB memory that contains JPEG
files or insert a disc that contains JPEG files.
2. Press the ◄► buttons to select My
Contents, and then press the ▲▼ buttons
to select Photos, and then press the ENTER
button.
3. Press the ▲▼◄► buttons to select the
folder you want to play, and then press the
ENTER button.
4. Press the ▲▼◄► buttons to select the
photo you want to play, and then press the
ENTER button.
✎ NOTE
 You can't enlarge PG graphic in the full screen
For CD function
mode.
CD COAXIAL  CD ANALOG
For AUX1 function
Using the TOOLS button
AUX1 HDMI3  AUX1 ANALOG
During the slide show playback, you
can use various function by pressing
the TOOLS button.
✎ NOTE
TOOLS
 You can also change the input mode by
pressing the AUDIO ASSIGN button on the
front of your Receiver.
 You can enjoy Dolby Digital or DTS if you
connect the digital audio output jack of an
external audio component to the optical or
coaxial digital audio input jack on the main
unit.
 For the TV function, the TV ARC menu will
be displayed only if an ARC-compliant TV is
connected.
S.DIRECT
Output the original signal as it is without
applying the sound field effect or any
other sound effect.
S.DIRECT
FULL
SCREEN
Tools
Pause Slide Show
Slide Show Speed :
Normal
Slide Show Effect :
Blind
Background Music :
Off
Background Music Setting
Zoom
Rotate
Picture Settings
Information
" Enter ' Return
• Pause Slide Show : Select to pause the slide
show.
• Slide Show Speed : Select to adjust the slide
show speed.
• Slide Show Effect : Select to set the slide
show effects.
• Background Music : Select to listen to music
while viewing a slide show.
English
HW-D7000_XAA_0321.indd 65
65
2011-03-21
2:02:21
Basic Functions
• Background Music Setting : Select to set the
background music.
• Zoom : Select to enlarge the current picture.
(Enlarge up to 4 times)
• Rotate : Select to rotate the picture. (Rotate
the picture either clockwise or counter
clockwise.)
• Picture Settings : Select to adjust the picture
quality.
• Information : Shows the picture information
including the name and size, etc.
✎ NOTE
My Contents
Videos
Connected Device
Photos
USB
Function
 Before you can enable the background music
function, the photo file should exist in the same
storage media with the music file. However,
the sound quality can be affected by the bit
rate of the MP3 file, the size of the photo and
the encoding method.
Playing back a USB Storage Device
F
Internet
Settings
" Enter ' Return
Safely Remove USB d WPS(PBC)
3.
Press the ENTER button.
4.
Press the ▲▼◄► buttons to select
Videos, Music or Photos, and then press the
ENTER button.
5.
For playing back Video, Music or Photo files,
refer to pages 56~66.
 If the system is connected to a BD Wise
compliant TV that has set BD Wise to On, the
Picture settings menu will not appear.
My Devices
Music
✎ NOTE
 You must remove the USB storage device safely
(by performing the “Safely Remove USB” function)
to prevent possible damage to the USB memory.
Press the MENU button to move to the home
menu, select the YELLOW (C) button, and then
press the ENTER button.
 If you insert a disc when playing files on a USB
storage device, the device mode changes to
“BD/DVD” automatically.
You can use the USB connection to play multimedia
files (MP3, JPEG, DivX, etc) downloaded from the
USB storage device.
1.
Move to the home menu.
My Contents
Videos
Photos
Music
Function
My Devices
Internet
Settings
d WPS(PBC)
2.
In Stop mode, connect the USB storage
device to the USB port on the front panel of
the product.
66
English
HW-D7000_XAA_0321.indd 66
2011-03-21
2:02:23
04
Using buttons on the Remote Control
1. Press the INPUT SELECT on the remote control
to select FM.
2. Tune in to the desired station.
• Preset Tuning 1 : You must first add a desired
frequency as a preset. Press the STOP ()
button to select PRESET and then press the
) button to select the preset
TUNING/CH (
station.
• Manual Tuning : Press the STOP () button to
select MANUAL and then press the TUNING/
CH (
) button to tune in to a lower or higher
frequency.
• Automatic Tuning : Press the STOP () button
to select MANUAL and then press and hold the
TUNING/CH (
) button to automatically
search the band.
Presetting Stations
Example : Presetting FM 89.10 into memory
1. Press the INPUT SELECT on the remote control
to select FM.
2. Press the TUNING/CH (
) button to select
<89.10>.
TUNER
3. Press the TUNER MEMORY button. MEMORY
C
• NUMBER flashes on the display.
4. Press the TUNER MEMORY button
again.
• Press the TUNER MEMORY button
before NUMBER disappears from the display.
• NUMBER disappears from the display and the
station is stored in memory.
5. To preset another station, repeat steps 2 to 4.
• To tune in to a preset station, press the
) button to select a channel.
TUNING/CH (
Using buttons on the Main Unit
1. Using the INPUT SELECT dial on the front panel
to select FM.
2. Tune in to the desired station.
Basic Functions
Listening to Radio
• Preset Tuning 1 : You must first add a desired
frequency as a preset. Press the STOP () or
TURNING MODE button to select PRESET
and then press the SELECT (
) button to
select the preset station.
• Manual Tuning : Press the STOP () or
TURNING MODE button to select MANUAL
and then press the SELECT (
) button to
tune in to a lower or higher frequency.
• Automatic Tuning : Press the STOP () or
TURNING MODE button to select MANUAL
and then press and hold the SELECT (
)
button to automatically search the band.
Presetting Stations
Example : Presetting FM 89.10 into memory
1. Using the INPUT SELECT dial on the front panel
to select FM.
2. Press the SELECT (
) button to select
<89.10>.
3. Press the MEMORY button.
• NUMBER flashes on the display.
4. Press the MEMORY button again.
• Press the MEMORY button before NUMBER
disappears from the display.
• NUMBER disappears from the display and the
station is stored in memory.
5. To preset another station, repeat steps 2 to 4.
• To tune in to a preset station, press the
SELECT (
) button to select a channel.
Setting Mono/Stereo
Press the MO/ST button.
• Each time the button is pressed, the
sound switches between STEREO and
MONO.
• In a poor reception area, select MONO for a
clear, interference-free broadcast.
English
HW-D7000_XAA_0321.indd 67
67
2011-03-21
2:02:26
Basic Functions
Playing Music
Connecting an iPod/iPhone Using the
USB Cable
If the Receiver is connected to an iPod/iPhone using
the provided USB cable, you can play music in
iPod/iPhone through the Receiver.
My Contents
Videos
Connected Device
Photos
iPod
MASTER VOLUME
ASC MIC
MENU
RETURN
AUDIO
ASSIGN
AUDIO
EFFECT
VIDEO
AUDIO
Function
PHONES
3D SOUND
Music
My Devices
Internet
Settings
" Enter ' Return
AUX 1 IN
d WPS(PBC)
1. Connect an iPod/iPhone using the USB
cable to the front USB port.
• Your iPod is automatically turned on.
• The “iPod” message appears on the TV
screen.
2. Press the ENTER button.
3. Select the music file to play.
- You can use the remote control or the
product to control simple playback functions
such as the PLAY, PAUSE, STOP, # /$
and /buttons. (See page 19.)
✎ NOTE
 If you want to return to the iPod menus while the
iPod player is connected using the USB cable,
press INPUT SELECT on the remote control or
using the INPUT SELECT dial on the front panel
and select R-IPOD. The FUNCTION mode
switches as follows: BD/DVD SAT GAME AUX1 AUX2 CD R-IPOD FM TV
Connecting an iPod/iPhone Using the Dock
ARC
(MONITOR)
HDMI 1
(SAT)
iPod
VIDEO IN
SAT
GAME
VIDEO OUT
TV
COMPONE
1
(SAT)
MONITOR
(GA
Y
PB/CB
PR/CR
SAT
FM ANT
68
GAME
TV
AUDIO IN
 Adjust the volume to a moderate level before
you connect your iPod to the product.
 When the product is on and you connect an
iPod, the product will charge the iPod's
battery.
 Make sure to connect the dock connector
so that the label “” faces upward.
You can play video files stored in the iPod player
by connecting it to the product.
HDMI OUT
iPod
✎ NOTE
Watching a Movie
If the Receiver is connected to the iPod/iPhone
specific dock, you can play videos or music in an
iPod/iPhone through the Receiver.
LAN
1. Connect the iPod dock connector to the iPod
Jack on the rear panel of the product.
2. Place the iPod in the supplied iPod Dock.
• Your iPod automatically turns on.
• The “iPod” message appears on the TV
screen.
3. Press the ENTER button.
4. Press the ◄▲▼ buttons to select Music,
and then press the ENTER button.
5. Select the music file to play.
- You can use the remote control or product
to control simple playback functions such
as the PLAY, PAUSE, STOP, #/ $, /
 and REPEAT buttons. See page 19.
CD
IN
1. Connect the iPod dock connector to the iPod
Jack on the rear panel of the product.
2. In the iPod screen, move to Videos >
Settings, then set the TV Out option and the
TV signal.
3. Place the iPod in the supplied iPod Dock.
• The “iPod” message appears on the TV
screen.
4. Press the ENTER button.
English
HW-D7000_XAA_0321.indd 68
2011-03-21
2:02:29
04
✎ NOTE
 You must have the VIDEO output




(Composite) connected to your TV to view
iPod video.
If you want to play iPod video via VIDEO
output, set Anynet+ (HDMI-CEC) to off.
No screen but the playback screen will
appear on the TV. View other iPod screens
on the iPod player.
If the connected iPod does not support
video playback, the "Playing video files is not
supported on this iPod model." message
appears when you select the Video menu.
If you want to return to the iPod menus while
the iPod player is connected using the dock,
press INPUT SELECT on the remote
control or press INPUT SELECT on the front
panel of the system and select R-IPOD. The
FUNCTION mode switches as follows :
BD/DVD SAT GAME AUX1 AUX2 CD
R-IPOD FM TV
iPod/iPhone Models You Can Use with
This Product
 iPod touch (3rd generation)
 iPod touch (2nd generation)
 iPod touch (1st generation)
 iPod classic
 iPod with video
 iPod with dock connector
 iPod with Click Wheel





iPod nano (5th generation)
iPod nano (4th generation)
iPod nano (3rd generation)
iPod nano (2nd generation)
iPod nano (1st generation)




iPhone 4
iPhone 3GS
iPhone 3G
iPhone
✎ NOTE
 “Made for iPod” means
that an electronic
accessory has been
designed to connect specifically to iPods
and has been certified by the developer to
meet Apple performance standards.
 “Made for iPhone” means that an electronic
accessory has been designed to connect
specifically to iPhones and has been certified
by the developer to meet Apple
performance standards.
 Apple is not responsible for the operation of
this device or its compliance with safety and
regulatory standards.
 The volume control may not operate
normally with iPod and iPhone models not
listed above. If you have a problem with any
of the models listed above, please update
the software of the iPod/iPhone to the
lastest version.
 Depending on the software version of the
iPod, control problems may occur. This is
not a malfunction of the product.
 Depending on the software version or the
type of the iPod, some operations may
differ. Install the latest iPod software.
(recommended)
 Some actions like iPod SYNC may depend
on video sources or the iPod model you
have.
 You can enjoy music or videos through the
BD/DVD function and enjoy music, videos or
photos through the Remote iPod function.
You need to use iPod Dock to enjoy videos
or photos.
 Playback of applications' contents through
the product is not guaranteed. We
recommend playing contents downloaded
to the iPod.
 If you have a problem using your iPod,
please visit www.apple.com/support/ipod
English
HW-D7000_XAA_0321.indd 69
Basic Functions
5. Press the ◄▲▼ buttons to select Video, and
then press the ENTER button.
6. Select the video file to play.
- You can use the remote control or the
product to control simple playback functions
such as the PLAY, PAUSE, STOP, # /$
and /buttons. (See page 19.)
69
2011-03-21
2:02:33
Network Services
You can enjoy various network services such as
Smart Hub or BD-LIVE by connecting the
product to your network.
Read the following instructions before using
any network service.
1. Connect the product to the network.
(see pages 32~33)
2. Configure the network settings.
(see pages 47~50)
3. The Smart Hub screen appears.
✎ NOTE
 Certain applications are available only in certain
countries.
4. The Terms of Service Agreement screen
appears.
If you want to agree, press the ◄► buttons to
select Agree, then press the ENTER button.
✎ NOTE
 Screens can take a few seconds to appear.
Using Smart Hub
Using Smart Hub, you can stream movies,
videos, and music from the Internet, access
various for pay or free-of-charge applications and
view them on your TV. Application content
includes news, sports, weather forecasts, stock
market quotes, maps, photos, and games.
5. The Service Update screen appears and
installs a number of services and applications.
When done, it closes. The applications and
services downloaded are displayed on the
Smart Hub screen. This may take some time.
✎ NOTE
 Smart Hub may close momentarily during the
You can also start this function by
pressing the SMART HUB button
on the remote control.
installation process.
 A number of screens may appear after
installation. You can press the ENTER button
to close them or let them close on their own.
Starting Smart Hub the First Time
To start Smart Hub for the first time, follow these
steps :
6. To start an application, press the ▲▼◄►
buttons to highlight a widget, then press the
ENTER button.
1. Go to the Home menu.
My Contents
Videos
Photos
Music
Function
My Devices
Internet
Settings
Safely Remove USB d WPS(PBC)
2. Press the ◄► buttons to select Internet,
and press the ENTER button.
70
English
HW-D7000_XAA_0321.indd 70
2011-03-21
2:02:33
05
1
2
3
4
6
Navigation Help : Displays the remote control
buttons you can use to navigate in Smart Hub.
• RED (A) : To log in to Smart Hub.
• GREEN (B) : To sort the applications.
• YELLOW (C) : To edit the applications.
• BLUE (D) : To change the settings of Smart
Hub.
7
My Applications : Displays your personal gallery
of applications which you can add to, modify, and
delete.
5
Search
Samsung Apps
Your Video
Contents 1
Contents 2
Contents 3
Contents 4
Recommended
Contents 1
Contents 2
Contents 3
Contents 4
Contents 5
Contents 6
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
Contents 1
Contents 2
Contents 3
Contents 4
Contents 5
Contents 6
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
Contents 7
Contents 8
Contents 9
Contents 10
Contents 11
Contents 12
Contents 13
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
a Login b Sort by Edit Mode d Settings
7
6
1
Commercial : Displays the Smart Hub Guide,
an introduction to the product, and new
application introductions.
2
Your Video : Provides recommendations for
videos based on your tastes.
• Lets you see movie recommendations
based on your previous preferences.
• Lets you select a movie, displays a list of
VOD (Video on Demand) providers that
have the movie, and then lets you choose
a provider for streaming. (Streaming is
unavailable in some areas.)
• For instructions to use Your Video, please
visit www.samsung.com.
3
Search : Provides an integrated search of
your video providers and connected AllShare
devices.
• Usable while using Smart Hub (except
when you are watching a Blu-ray Disc).
• For easy access, use the SEARCH button
on the remote control.
• For instructions to use search function,
please visit www.samsung.com.
4
Samsung Apps : You can download various for
pay or free-of-charge application services.
5
Recommended : Displays recommended
contents managed by Samsung.
✎ NOTE
 Samsung Electronics takes no legal
responsibility for any interruption of the Smart
Hub service caused by the service provider for
any reason.
 The Smart Hub service downloads and
processes data via the Internet so that you can
enjoy the Internet contents on your TV screen.
If the Internet connection is unstable, the
service may be delayed or interrupted.
Furthermore, the product may turn off
automatically in response to conditions on the
Internet.
If this occurs, check the Internet connection
and try again.
 Application services may be provided in
English only and the contents available may
vary, depending on your area.
 For more information about a Smart Hub
service, visit the web site of the applicable
service provider.
 The services provided are subject to change
by the Smart Hub service provider without
notice.
 The Smart Hub service contents may differ
depending on the product’s firmware version.
 For pay DivX contents with copy protection
can only be played through a composite, a
component or an HDMI cable.
English
HW-D7000_XAA_0321.indd 71
Network Services
Smart Hub at a Glance
71
2011-03-21
2:02:35
Network Services
Using the Keypad
Creating an Account
Through your remote, you can use the OnScreen Keypad to enter letters, numbers, and
symbols.
To establish your own, exclusive, configuration of
Smart Hub, create your own Smart TV Account.
To create an account, follow these steps:
1.
1
2
1
2
3
.,–
abc
def
4
5
6
ghi
jkl
mno
7
8
9
pqrs
tuv
wxyz
Search
Your Video
Contents 1
T9
Delete
ab
Ab
AB
1
6
Smart TV ID

Contents 1
xxxxxxxx
Press [ENTER]
Contents 4
Contents 2
Contents 1
Contents 2
xxxxxxxx
xxxxxxxx
Contents 4
Contents 5
xxxxxxxx
xxxxxxxx
Contents 3
Login
xxxxxxxx
The current keypad.
Use to enter letters, numbers, and symbols.
2
Press the FULL SCREEN button on the remote
control to shift the input mode.
: ab, Ab, AB, numbers or icons.
3
Displays the current input mode.
4
Press the GREEN (B) button on the remote
control to change the input method. (T9 or ABC)
5
Press the TOOLS button on the remote control
to change the language.
6
Press the REPEAT button on the remote control
to delete a character.
Cancel
xxxxxxxx
Contents 5
Contents 6
xxxxxxxx
xxxxxxxx
Contents 8
Contents 9
Contents 10
Contents 11
Contents 12
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
xxxxxxxx
a Login b Sort by Edit Mode d Settings
2.
Press the ▲▼◄► buttons to select Create
Account, and then press the ENTER
button.
3.
On the next screen, select Smart TV ID, and
then press the ENTER button. An entry
screen and keypad appear.
4.
Use the keypad to enter your e-mail
address. This will serve as your ID.
✎ NOTE
 The keypad works like the keypad on a cell
phone.
5.
When done, press the ENTER button to
select OK, and then press the ENTER
button again. The Create Account screen reappears.
6.
Select Password, and then press the
ENTER button. The Password screen and a
keypad appear.
7.
Use the keypad to enter a password.
The password can be any combination of
letters, numbers, and symbols.
Entering Text, Numbers and Symbols
To enter text, press the number button on the
remote that corresponds to the letter you want to
enter. Press the button rapidly to enter a letter
that is not the first letter listed on the On-Screen
keypad button. For example, if you want to enter
the letter b, press the 2 button on your remote
rapidly twice. To enter the first letter listed on a
button, press, release, and then wait.
To move within the text, use the Arrow buttons.
To delete text, move the cursor to the right of the
character you want to delete, and then press the
REPEAT button. To change case or enter
numbers or punctuation, press the FULL
SCREEN button.
Contents 4
Find Password
Contents 7
5
1
%
Contents 3
Press
[ENTER]xxxxxxxx
xxxxxxxx
Create Account
72
Contents 3
 Remember my Smart TV ID and password
b Input Method / Language: English
4
Contents 2
Recommended
Password
3
Samsung Apps
Login
0
Shift
Press the RED (A) button on your remote
control. The Login screen appears.
✎ NOTE
 Press the RED (A) button on your remote to
show or hide the password as you enter it.
English
HW-D7000_XAA_0321.indd 72
2011-03-21
2:02:36
05
When done, press the ENTER button to
select OK, and then press the ENTER
button again. The Create Account screen
re-appears.
9.
Select Confirm password, and then press
the ENTER button.
10. Repeat Steps 7 and 8.
11. When the Create Account screen reappears, select Create Account, and then
press the ENTER button. The Confirmation
window appears.
12. Select OK, and then press the ENTER
button. The Continue to Register Service
window appears.
13. Select Connect Service, and then press the
ENTER button.
2.
Select the Down Arrow next to the Smart
TV ID field, and then press the ENTER
button.
3.
Select your ID from the list that appears, and
then press the ENTER button. The Login
screen re-appears.
4.
Select Password, and then press the
ENTER button. The Password window and
a keypad appears.
5.
Using the keypad and your remote, enter
your password. When done, press the
ENTER button, select OK, and then press
the ENTER button again.
✎ NOTE
 If you want Smart Hub to enter your password
automatically, select Remember my Smart TV
ID and password after you have entered your
password, and then press the ENTER button.
A check appears. Smart Hub will now enter
your password automatically when you select
or enter your ID.
14. The Register Service Account Window
appears. If you want to register, Select Go
Register and then press the ENTER button.
• If you have existing accounts with any of
the listed providers, you can associate the
provider account and the provider account
password with your Smart TV Account.
Registration makes it easier to access
the providers web site. For registration
instructions, go to Step 2 in Account
Management under the Settings Menu.
• If you don’t have existing provider accounts
or do not want to register existing accounts
at this time, select Register Later, and then
press the ENTER button. You can also let the
window close on its own in about a minute.
✎ NOTE
 You must use an e-mail address as an ID.
 You can register up to 10 User Accounts.
 You do not need an account to use Smart
Hub.
Account Log In
To log in to your Smart TV Account, follow these
steps:
1.
With the Smart Hub main screen displayed
on your TV, press the RED (A) button on
your remote. The Login screen appears.
The Settings Menu - BLUE (D)
The Settings Menu Screen gives you access to
account management, account reset, and
account properties functions.
To access the Settings Menu, and then select a
menu item, follow these steps:
1.
Press the BLUE (D) button on your remote.
2.
Press the ▲▼ to select a menu item, and
then press the ENTER button.
The functions on the Settings Menu screen are
described below.
✎ NOTE
 The Service Manager item listed in the Settings
Menu is not available for Blu-ray Home
Theaters.
Account Management
The Account Management Menu contains
functions that let you register your service
provider accounts, change your Smart Hub
password, and delete or deactivate your Smart
TV Account.
English
HW-D7000_XAA_0321.indd 73
Network Services
8.
73
2011-03-21
2:02:38
Network Services
Register Service Account
Change Password
If you have existing accounts with any of the
providers listed by the Register Service Account
function, you can associate the provider account
and the provider account password with your
Smart TV Account. If you associate the account,
you will be able to log onto the account through
Smart Hub easily, without entering your account
name or password.
The Change Password function lets you change
your Smart Hub password. To change the
password, follow these steps:
To use the Account Management function, follow
these steps:
1.
2.
In the Account Management menu, select
Register Service Account, and then press
the ENTER button. The Register Service
Account Window appears.
Press the ▲▼ arrow buttons to select a
Service Provider you want to associate with
your Smart TV Account, and then press the
ENTER button.
✎ NOTE
 If you have a Samsung account and you want
to use the Samsung Apps function in Smart
Hub, you must register your Samsung Apps
account here. See page 77 for more
information.
3.
Using your remote and the on-screen
Keypad, enter your site ID and password.
When done, press the ENTER button.
✎ NOTE
 This is the ID and password you normally use
to access your account on this site.
4.
If you have entered the ID and password
correctly, the Registered Successfully
message appears.
5.
If you pressed OK, repeat Steps 2 through 4
to associate another Service Provider.
6.
When you are done, press the RETURN
button.
74
1.
Select Change Password, and then press
the ENTER button.
2.
Enter your current password. The next
screen appears.
3.
On the next screen, enter a new password
on the first line. Enter it again on the second
line to confirm.
4.
The Changing Password Complete message
screen appears. Press the ENTER button or
wait for the screen to close - about 5
seconds.
Remove from TV Account List
The Remove from TV Account List function
cancels all your current registered Service
Accounts that you registered on the Register
Service Account screen.
Deactivate Account
The Deactivate Account function deactivates your
Smart TV Account and deletes it and all your
account settings entirely from Smart Hub.
Reset
The Reset function initializes all downloaded
widgets, erases all user accounts and settings
from the product, and resets all Smart Hub
settings to the factory default settings. It then
restarts Smart Hub as if it were starting for the
first time. Your account, however, remains on the
Smart Hub server. To log into your account, enter
your ID and password on the Create Account
screen.
To use the Reset function, follow these steps:
1.
In the Account Management menu, select
Reset, and then press the ENTER button.
The Reset screen appears.
2.
Enter the your Security password. This is the
password you entered if you set up a BD or
DVD Parental rating (See page 52). If you did
not, enter 0000.
English
HW-D7000_XAA_0321.indd 74
2011-03-21
2:02:38
05
4.
After a few moments, Smart Hub
automatically resets. The screen may go
black, then Smart Hub re-appears. In a few
moments, it starts the re-initialization
procedure.
To complete the re-initialization, go to Step 4
in Starting Smart Hub for the First Time. (See
page 70)
✎ NOTE
The functions in the Edit Mode Menu bar are
described below.
✎ NOTE
 Some menu items may not appear on the
screen. To see these items, press the ◄► to
move to the screen edge, and then press one
more time to reveal the items.
 You can close the bar by highlighting the X on
the bottom right side, and then pressing the
ENTER button.
 If you forgot your password, press the STOP
( ) button on the front panel of the product
for more than 5 seconds with no disc inserted.
Properties
The Properties menu item lists three functions
that display information about Smart Hub :
Detail
Lists information about Smart Hub including
version number, the number of services installed,
memory usage, and the unique product ID.
Move
The Move function lets you change the screen
position of a widget. To use the Move function,
follow these steps:
1.
Press the YELLOW (C) button on your
remote.
2.
Select a widget, and then press the ENTER
button. A check appears above the widget.
3.
Press the ▲▼◄► to select Change
Position, and then press the ENTER button.
A position change icon appears above the
widget.
4.
Press the ▲▼◄► to move the icon. Press
the ENTER button when the icon is in the
position of your choice. The widget moves to
its new location.
Terms of Service Agreement
Displays the Terms of Service Agreement.
The Edit Mode Menu - YELLOW (C)
The functions in the Edit Mode menu let you
manipulate the widgets in the My Applications
section of the Smart Hub screen. Using these
functions, you can lock and unlock access to
some widgets, New Folder and move widgets to
them, rename folders, delete widgets, and
change the position of widgets on the screen.
New Folder
The New Folder function lets you create and
name new folders. Once you have created a
folder, you can move widgets into it. To use the
New Folder function, follow these steps:
To access the Edit Mode Menu, and then select
a menu item, follow these steps:
1.
Press the YELLOW (C) button on your
remote.
1.
Press the YELLOW (C) button on your
remote. The Edit Mode menu bar appears
on the bottom of the screen.
2.
2.
Press the ▲▼◄► to select a menu item,
and then press the ENTER button.
Press the ▲▼◄► to move the cursor to
New Folder, and then press the ENTER
button. The New Folder window and a
keypad appear.
3.
Use the keypad to enter the name of the
folder, and then press the ENTER button.
The New Folder screen closes and the New
Folder appears on the Smart Hub screen.
English
HW-D7000_XAA_0321.indd 75
Network Services
3.
75
2011-03-21
2:02:38
Network Services
Move to Folder
Rename Folder
The Move to Folder function lets you move a
widget to a folder. To use the Move to Folder
function, follow these steps:
The Rename Folder function lets you rename
folders. To use the Rename Folder function,
follow these steps:
1.
Press the YELLOW (C) button on your
remote.
1.
Press the YELLOW (C) button on your
remote.
2.
Select a widget, and then press the ENTER
button.
2.
Press the ▲▼◄► to select a folder, and
then press the ENTER button.
3.
Press the ▲▼◄► to select Move to Folder,
and then press the ENTER button. The
Move to Folder window opens.
3.
4.
Press the ▲▼◄► to select a folder, and
then press the ENTER button. The Moved to
Folder message appears, and then closes.
The widget has been moved to the folder.
Press the ▲▼◄► to select Rename a
Folder, and then press the ENTER button.
The Folder Rename window and a keyboard
appears.
4.
Use the key board to enter a new name, and
then press the ENTER button. The Rename
window closes and the new name appears
below the folder.
To Access Widgets in a Folder
Lock
1.
Close the Edit Mode menu.
2.
In My Applications, press the ▲▼◄► to
select a folder, and then press the ENTER
button. The folder opens.
The Lock function lets you lock some widgets in
My Applications so they can not be opened
without entering the Parental Security Code.
3.
Select a widget, and then press the ENTER
button. The widget’s application or service
starts.
To use the Lock function, follow these steps:
To Edit Items in a Folder
1.
Press the YELLOW (C) button on your
remote.
2.
Press the ▲▼◄► to select a widget, and
then press the ENTER button. If the widget
can be locked, the Lock menu item is
enabled.
3.
Press the ▲▼◄► to select Lock, and then
press the ENTER button. The Security
window appears.
4.
Enter your Parental Security Code (See page
52). If you have not created a Parental
Security Code, enter 0000.
5.
Press the ENTER button. The Lock Service
window appears confirming the lock, and
then closes. A lock symbol appears next to
the widget.
Select a folder, and then press the ENTER
button. The folder opens.
Press the YELLOW (C) button on your remote.
The Edit buttons appear at the bottom of the
screen.
These buttons work the same as the Edit Mode
menu buttons on the main screen. For example,
to move a widget back to the My Applications
main screen:
1.
Select the widget.
2.
Select Move to Folder, and then press the
ENTER button. The Move to Folder window
appears.
3.
Select My Applications, and then press the
ENTER button. The Move to Folder window
closes and the widget returns to the main
My Applications screen.
76
English
HW-D7000_XAA_0321.indd 76
2011-03-21
2:02:38
05
1.
Press the YELLOW (C) button on your
remote.
2.
Press the ▲▼◄► to select a locked
widget, and then press the ENTER button.
3.
Press the ▲▼◄► to select Unlock, and
then press the ENTER button. The Security
window appears.
4.
Enter the Parental Security Code (See page
52). If you have not created a Parental
Security Code, enter 0000.
5.
Press the ENTER button. The Lock Service
Released window appears confirming the
lock has been release, and then closes.
Samsung Apps
Samsung Apps lets you download for pay or
free-of-charge applications and services to your
Blu-ray Home Theater and view or use them on
your TV.
These applications and services include videos,
music, photos, games, news, sports, etc.
Widgets for the new apps appear in My
Applications.
Additional applications and services are added
regularly.
For Pay Apps
Delete
To download for pay apps, you need to create a
Samsung Account and add a credit card to the
account.
The Delete function lets you delete widgets from
My Applications. To use the Delete function,
follow these steps:
To create a Samsung account, please visit www.
samsung.com
1.
Press the YELLOW (C) button on your
remote.
2.
Press the ▲▼◄► to select a widget, and
then press the ENTER button.
3.
Press the ▲▼◄► to select Delete, and
then press the ENTER button. The
message, "Do you want to delete selected
item(s)?" appears.
4.
Select Yes, and then press the ENTER
button. The widget is deleted.
The Sort by Menu - GREEN (B)
The functions in the Sort Menu let you sort the
widgets in My Applications by Name, Date,
Frequency (of use), and Category. If you manually
change the position of a widget, the Sort Menu
automatically highlights User Defined when you
start it.
Network Services
Unlock
✎ NOTE
 This service may not provided in some
countries.
Accessing the Samsung Apps Screen
To access Samsung Apps, press the ▲▼◄►
buttons to navigate to the Samsung Apps area
on the Smart Hub main screen, and then press
the ENTER button. The Samsung Apps screen
appears.
✎ NOTE
 If this is the first time you are accessing this
screen, the terms of service window appears.
Select Agree, and then press the ENTER
button.
To sort the widgets in My Applications, follow
these steps:
1.
Press the GREEN (B) button on your remote.
2.
Press the ◄► to select a sorting method,
and then press the ENTER button. Smart
Hub sorts the widgets by the method you
have chosen.
English
HW-D7000_XAA_0321.indd 77
77
2011-03-21
2:02:39
Network Services
Using the Samsung Apps Screen
Samsung Apps by category
To use the Samsung Apps screen, follow these
steps:
The following categories are available:
1.
Press the ◄► buttons to move to the
category list on the left.
2.
Press the ▲▼ to highlight a category. In a
few seconds, the Samsung Apps screen
displays the applications in that category.
The Sort tabs appear across the top.
3.
Press the ► button to move to the displayed
applications or services.
4.
Press the ▲▼◄► buttons to select an
application or service, and then press the
ENTER button. The Application Details
screen appears describing the service or
application.
5.
✎
Select Download Now, and then press the
ENTER button. If the application or service is
free, it downloads and runs. If not, and there
is a fee, follow the directions on the screen
to complete the download.
NOTE
 Some apps are free to download, but require
registration with the provider or a paid account
with the provider to use.
 Widgets for applications and services you have
downloaded from Samsung Apps appear in
My Applications.
• What’s New? : Displays newly registered
applications.
• Video : Displays various video media such as
movies, TV shows, and short length videos.
• Game : Displays various games such as sudoku
and chess.
• Sports : Displays various sports media services
such as match information, images, and short
length videos.
• Lifestyle : Includes various lifestyle media services
such as music, personal photo management
tools, and social networking such as Facebook
and Twitter.
• Information : Includes various information services
such as news, stocks, and weather.
• Other : Includes other miscellaneous services.
My Account
My Account gives you access to your Samsung
Apps order and download history, and to the My
Apps Cash screen. You must have a Samsung
account to access this information.
Help
If you have questions about Samsung Apps,
check Help first. If none of the tips apply, please
visit www.samsung.com.
Sort By Tabs
To use the Help function, follow these steps:
You can access the Sort By tabs on the top of
the screen using the ▲▼◄► buttons. Each tab
displays the services or applications in the
category you chose, sorted by the criteria on the
tab (Recommended, Most Downloaded, Most
Recent, Name).
1.
Press the ▲▼◄► buttons to select Help,
and then press the ENTER button.
2.
Press the ◄► to enter Help after it appears.
3.
Press the ▲▼ to scroll the Help text.
4.
Press the ◄ to exit Help.
You can also use the BLUE (D) button on your
remote to access the Sort By tabs. Each time
you press the BLUE (D) button, you change the
display from one sort tab to the next.
78
English
HW-D7000_XAA_0321.indd 78
2011-03-21
2:02:39
05
• RED (A) (Login) : To log into your Smart TV
Account.
• GREEN (B) (Thumbnail/List View) : To toggle
applications between Thumbnail and List view.
• BLUE (D) (Sort By) : To sort the applications in a
category by Recommended, Most Downloaded,
Most Recent, or Name.
• Return : To return to the previous menu.
✎
NOTE
 The Internet contents services may be added
or deleted by providers without notice.
For instructions to use Your Video or Search
Function, please visit www.samsung.com
Using the AllShare Function
AllShare lets you play music, video, and photo files
located in your PC or your DLNA compatible mobile
phone or NAS on the product.
To use AllShare with your product, you must
connect the product to your network (See pages
32~33).
To use AllShare with your PC, you must install
AllShare software on your PC.
Network Services
Using the colored buttons on your
remote with Samsung Apps
If you have a DLNA compatible mobile phone or
NAS, you can use AllShare without any additional
software.
You can download the PC software and get detailed
instructions for using AllShare from the Samsung.
com web site.
Using vTuner Function
vTuner is the fuction of the listening a
radio. If you press the vTuner button,
you can move to vTuner widget.
Press the vTuner button.
✎ NOTE
 You can use the vTuner Function after download
the vTuner widget from Samung Apps.
BD-LIVE™
Once the product is connected to the network,
you can enjoy various movie-related service
contents using a BD-LIVE compliant disc.
1. Attach a USB memory stick to the USB jack
on the front of the product, and then check
its remaining memory. The memory device
must have at least 1GB of free space to
accommodate the BD-LIVE services.
2. Insert a Blu-ray disc that supports BD-LIVE.
3. Select an item from various BD-LIVE service
contents provided by the disc manufacturer.
✎ NOTE
 The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
English
HW-D7000_XAA_0321.indd 79
79
2011-03-21
2:02:39
Other Information
Troubleshooting
Refer to the chart below when this product does not function properly. If the problem you are
experiencing is not listed below or if the instructions below do not help, turn off the product,
disconnect the power cord, and contact Samsung Electronics at 1-800-SAMSUNG (1-800-726-7864).
Symptom
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
The iPod fails to connect.
• Check the condition of the iPod connector and Dock.
• Keep the iPod software version up to date.
Playback does not start.
• Check the region number of the BD/DVD.
BD/DVD discs purchased from abroad may not be playable.
• CD-ROMs and DVD-ROMs cannot be played on this Product.
• Make sure that the rating level is correct.
Playback does not start
immediately when the
Play/Pause button is pressed.
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
Sound is not produced.
• The Receiver does not play sound during fast playback, slow playback,and step motion
playback.
• Are the speakers connected properly? Is the speaker setup correctly customized?
• Is the disc severely damaged?
Sound can be heard only from a
few speakers and not all 8.
• On certain BD/DVD discs, sound is output from the front speakers only.
• Check if the speakers are connected properly.
• Adjust the volume.
• When listening to a CD, radio or TV, sound is output to the front speakers only.
Select "3D SOUND, NEO:6, PRO LOGIC II" to use all peakers.
The sound from the left/right
channels is reversed.
• Are the left/right speaker or left/right input/output cables connected properly?
• Check the left/right channel and connect it/them correctly.
Dolby Digital 7.1 CH Surround
Sound is not produced.
• Is there "Dolby Digital 7.1 CH" mark on the disc? Dolby Digital 7.1 CH Surround Sound is
produced only if the disc is recorded with 7.1 channel sound.
• Is the audio language correctly set to Dolby Digital 7.1-CH in the information
display?
The remote control does not work.
• Are you operating the remote within its operational range and within the proper angle
relative to the sensor?
• Are the batteries drained?
• Have you selected the mode (BD-RX, TV, SHIFT) functions of the remote control (BD-RX,
TV, SHIFT) correctly?
• Disc is rotating but no
picture is produced.
• Picture quality is poor and
picture is shaking.
• Is the TV power on?
• Are the video cables connected properly?
• Is the disc dirty or damaged?
• A poorly manufactured disc may not be playable.
Audio language and subtitles do
not work.
• Audio language and subtitles will not work if the disc does not contain them.
80
English
HW-D7000_XAA_0321.indd 80
2011-03-21
2:02:39
06
Other Information
Symptom
Check/Remedy
Menu screen does not appear
even when the menu function is
selected.
• Are you using a disc that does not contain menus?
Aspect ratio cannot be changed.
• You can play 16:9 BD/DVDs in 16:9 Wide mode, 4:3 Letter Box mode, or 4:3
Pan - Scan mode, but 4:3 BD/DVDs can be seen in 4:3 ratio only. Refer to the
Blu-ray Disc jacket and then select the appropriate function.
• The product is not working.
(Example: The power goes out
or a strange noise is heard.)
• Press and hold the romote control's STOP ( ) button for 5 seconds in
STANDBY mode.
• The Product is not working
normally.
You have forgotten the rating
level password.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• Only S.DIRECT, TONE, SLEEP and AUDIO ASSIGN buttons will operate, after
pressing the SHIFT button.
• With no disc in the product, press and hold the product's STOP ( ) button for
longer than 5 seconds. INIT appears on the display and all settings will return
to the default values.
And then press the POWER button.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
Can't receive radio broadcasts.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an area
with good reception.
While listening to TV audio
through the Product, no sound is
heard.
• If the OPEN/CLOSE ( ) button is pressed while listening to TV audio using the
TV functions, the BD/DVD functions are turned on and the TV audio is muted.
"Not Available" appears on
screen.
• The features or action cannot be completed at this time because:
1. The BD/DVD’s software restricts it.
2. The BD/DVD’s software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
If the HDMI output is set to a
resolution your TV cannot support
(for example, 1080p), you may not
see a picture on your TV.
• Press and hold the STOP ( ) button on front panel for more than 5 seconds
with no disc inserted. All settings will revert to the factory settings.
No HDMI output.
• Check the connection between the TV and the HDMI jack of the product.
• Check if your TV supports 480p/720p/1080i/1080p HDMI input resolution.
Abnormal HDMI output screen.
• If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
English
HW-D7000_XAA_0321.indd 81
81
2011-03-21
2:02:39
Other Information
Symptom
Check/Remedy
There is no sound from surround
speakers.
• Are the surround speakers connected properly?
• Is Surround incorrectly set to NONE in the Speaker Size?
• Is surround mode set to stereo?
There is no sound from surround
back speakers
• Are the surround back speakers connected properly?
• Is SBACK (Surround Back) set to NONE in the Speaker Size?
• Is Surround Mode set to EX/ES?
Can't select EX/ES mode.
• Is SBACK (Surround Back) set to NONE in the Speaker Size?
• Is the input signal selected properly?
Can't select Dolby Pro Logic llx
mode.
• Is the input signal selected properly?
• Only 2 channel signal can select Dolby Pro Logic IIx mode. (ex:Dolby Digital,
PCM, 2 channel analog input signal.)
Can't select NEO:6 mode.
• Is the input signal selected properly?
• Use PCM and Analog input signal.
PC Share Manager function
I can see folders shared through
the PC Share Manager, but I
cannot see the files.
• Since it shows only files corresponding to the Image, Music, and Movie
categories, files that do not correspond to these categories may not be
displayed.
AllShare function
Video is played intermittently.
• Check if the network is stable.
• Check if the network cable is properly connected and if the network is not
overloaded.
• Wireless connection between the server and the product is unstable.
Check the connection.
AllShare connection between TV
and PC is unstable.
• IP address under the same subnetwork should be unique, otherwise IP collision
can results in such a phenomenon.
• Check if you have a firewall enabled.
If so, disable the firewall function.
82
English
HW-D7000_XAA_0321.indd 82
2011-03-21
2:02:40
06
Check/Remedy
BD-LIVE
I cannot connect to the BD-LIVE
server.
• Check whether the network connection is successful or not by using Network
Test menu.
• The memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 51)
• Please check whether the BD-LIVE Internet Connection menu is set to
Allow(All).
• If all above fails, contact the contents provider or update the latest firmware.
When using the BD-LIVE service,
an error occurs.
• The memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 51)
Other Information
Symptom
✎ NOTE
 When the factory default settings are restored, all the user data stored in the BD data will be deleted.
Repairs
If you contact us to repair your player, an administration fee may be charged if either:
1. An engineer is called out to your home at your request and there is no defect in the product.
2. You bring the unit to a repair center and there is no defect in the product.
We will provide you with the amount of the administration fee before we make a home visit or begin
any work on your product.
We recommend you read this manually thoroughly, search for a solution on line at www.samsung.
com, or contact Samsung Customer Care at 1-800-SAMSUNG (726-7864) before seeking to repair
your product.
English
HW-D7000_XAA_0321.indd 83
83
2011-03-21
2:02:40
Other Information
Specifications
General
FM Tuner
Power Requirements
AC 120V, 60Hz
Power Consumption
125 W
Weight
18.74 Ibs
Dimensions
16.92 (W) x 6.50 (H) x 14.19 (D) inches
Operating Temperature Range
+41°F to +95°F
Operating Humidity Range
10 % to 75 %
Signal/noise ratio
65 dB
Usable sensitivity
7 dB
Total harmonic distortion
0.9 %
BD (Blu-ray Disc)
Reading Speed : 9.834 m/sec
DVD (Digital Versatile Disc)
Disc
CD : 5 inches (COMPACT DISC)
CD : 3 1/2 inches (COMPACT DISC)
Composite Video
Reading Speed : 6.98 ~ 7.68 m/sec.
Approx. Play Time (Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
1 channel : 1.0 Vp-p (75 Ω load)
Blu-ray Disc : 480i
DVD : 480i
Y : 1.0 Vp-p (75 Ω load)
Video Output
Component Video
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
BD : 480i DVD : 480p, 480i
Video/Audio
HDMI
Front speaker output
1080p, 1080i, 720p, 480p
PCM multichannel audio, Bitstream audio, PCM audio
120W x 2(4Ω), THD 0.9%
Surround Back / Front Height speaker output 120W x 2(4Ω), THD 0.9%
Amplifier
Center speaker output
120W (4Ω), THD 0.9%
Surround speaker output
120W x 2(4Ω), THD 0.9%
Frequency response
Analog input
20Hz~20kHz (±3dB)
Digital input
20Hz~40kHz (±-4dB)
S/N Ratio
75dB (1KHz)
Channel separation
70dB (1KHz)
Input sensitivity
(AUX) 450mV
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
84
English
HW-D7000_XAA_0321.indd 84
2011-03-21
2:02:40
SAMSUNG Receiver
LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc. (SAMSUNG) and delivered new, in
the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and
workmanship for a limited warranty period of:
One (1) Year Parts and Labor*
(*90 days Parts and Labor for Commercial Use)
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States.
To receive warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. Warranty
service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon
request as proof of purchase to SAMSUNG or SAMSUNG's authorized service center. Transportation of the product to and from the
service center is the responsibility of the purchaser.
SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or
products if found to be defective during the limited warranty period specified above. All replaced parts and products become the
property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original
warranty, or ninety (90) days, whichever is longer.
SAMSUNG's obligations with respect to software products distributed by SAMSUNG under the SAMSUNG brand name are set
forth in the applicable end user license agreement. Non-SAMSUNG hardware and software products, if provided, are on an
“AS IS” basis. Non-SAMSUNG manufacturers, suppliers, publishers, and service providers may provide their own warranties.
This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, and except to the extent
otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including,
but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage or exterior finish; accidents, abuse, neglect, fire, water, lightning or
other acts of nature; use of products, equipment, systems, utilities, services, parts, supplies, accessories, applications, installations,
repairs, external wiring or connectors not supplied and authorized by SAMSUNG, or which damage this product or result in service
problems; incorrect electrical line voltage, fluctuations and surges; customer adjustments and failure to follow operating instructions,
cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book; product removal or
reinstallation; reception problems and distortion related to noise, echo, interference or other signal transmission and delivery
problems. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE,
AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT
TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR
PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE
LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE
FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND
PURCHASER°ØS PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS
NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state.
To obtain warranty hardware service, please contact SAMSUNG at:
Samsung Electronics America, Inc.
105 Challenger Road Ridgefield Park, NJ07660-0511
1-800-SAMSUNG(726-7864) and www.samsung.com
HW-D7000_XAA_0321.indd 85
2011-03-21
2:02:40
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care center.
Area
` North America
Canada
Mexico
U.S.A
Contact Center 
Web Site
1-800-SAMSUNG (726-7864)
01-800-SAMSUNG (726-7864)
1-800-SAMSUNG (726-7864)
www.samsung.com
www.samsung.com
www.samsung.com
0800-333-3733
0800-124-421 / 4004-0000
800-SAMSUNG (726-7864)
01-8000112112
0-800-507-7267
1-800-751-2676
1-800-10-7267
800-6225
1-800-299-0013
800-7919267
1-800-234-7267
00-1800-5077267
800-7267
0-800-777-08
1-800-682-3180
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
1-800-SAMSUNG (726-7864)
www.samsung.com
0-800-100-5303
www.samsung.com
42 27 5755
0810 - SAMSUNG (7267864,
€ 0.07/min)
-
` Latin America
Argentine
Brazil
Chile
Colombia
Costa Rica
Dominica
Ecuador
El Salvador
Guatemala
Honduras
Jamaica
Nicaragua
Panama
Peru
Puerto Rico
Trinidad &
Tobago
Venezuela
Austria
Belgium
02-201-24-18
Bosnia
Bulgaria
Croatia
05 133 1999
07001 33 11
062 SAMSUNG (062 726 7864)
800-SAMSUNG (800-726786)
Samsung Zrt., česká organizační
složka, Oasis Florenc, Sokolovská394/17, 180 00, Praha 8
70 70 19 70
030 - 6227 515
01 48 63 00 00
01805 - SAMSUNG (726-7864
€ 0,14/Min)
06-80-SAMSUNG (726-7864)
800-SAMSUNG (726-7864)
+381 0113216899
261 03 710
023 207 777
020 405 888
0900-SAMSUNG
(0900-7267864) (€ 0,10/Min)
815-56 480
0 801 1SAMSUNG (172678)
/ 022-607-93-33
80820-SAMSUNG (726-7864)
1. 08010 SAMSUNG (72678) doar din reţeaua Romtelecom,
tarif local
2. 021.206.01.10 - din orice
reţea, tarif normal
Czech
Denmark
Finland
France
Germany
Hungary
Italia
Kosovo
Luxemburg
Macedonia
Montenegro
Netherlands
Norway
Poland
Portugal
Rumania
HW-D7000_XAA_0321.indd 86
Slovakia
Spain
Sweden
Contact Center 
0700 Samsung (0700 726
7864)
0800-SAMSUNG (726-7864)
902-1-SAMSUNG (902 172 678)
0771 726 7864 (SAMSUNG)
Switzerland
0848-SAMSUNG (7267864,
CHF 0.08/min)
U.K
Eire
Lithuania
Latvia
Estonia
0330 SAMSUNG (7267864)
0818 717100
8-800-77777
8000-7267
800-7267
Uzbekistan
Kyrgyzstan
Tadjikistan
Ukraine
0-800-502-000
www.samsung.com
Belarus
Moldova
810-800-500-55-500
00-800-500-55-500
www.samsung.com/
be (Dutch)
www.samsung.com/
be_fr (French)
www.samsung.com
www.samsung.com
` Asia Pacific
www.samsung.com
Russia
Georgia
Armenia
Azerbaijan
Kazakhstan
Australia
New Zealand
China
1300 362 603
0800 SAMSUNG (0800 726 786)
400-810-5858 / 010-6475 1880
Hong Kong
(852) 3698 4698
India
Indonesia
www.samsung.com
www.samsung.com
www.samsung.com
Japan
Malaysia
www.samsung.com
Philippines
www.samsung.com
www.samsung.com
www.samsung.com
-
Singapore
Thailand
Taiwan
Vietnam
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
Web Site
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/ch
www.samsung.com/
ch_fr/(French)
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
` CIS
8-800-555-55-55
8-800-555-555
0-800-05-555
088-55-55-555
8-10-800-500-55-500
(GSM: 7799)
8-10-800-500-55-500
00-800-500-55-500
8-10-800-500-55-500
` Europe
Albania
Area
Serbia
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.ua
www.samsung.com/
ua_ru
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/hk
www.samsung.com/
hk_en/
3030 8282 / 1800 110011 /
1800 3000 8282 / 1800 266 8282
0800-112-8888 /
021-5699-7777
0120-327-527
1800-88-9999
1-800-10-SAMSUNG(726-7864) /
1-800-3-SAMSUNG(726-7864) /
1-800-8-SAMSUNG(726-7864) /
02-5805777
1800-SAMSUNG (726-7864)
1800-29-3232 / 02-689-3232
0800-329-999
1 800 588 889
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
8000-4726
08000-726786
800-22273
080 100 2255
800-SAMSUNG (726-7864)
9200-21230
444 77 11
800-SAMSUNG (726-7864)
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
0800-SAMSUNG (726-7864)
0860-SAMSUNG (726-7864 )
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
` Middle East
Bahrain
Egypt
Jordan
Morocco
Oman
Saudi Arabia
Turkey
U.A.E
` Africa
Nigeria
South Africa
2011-03-21
2:02:40
QUESTIONS OR COMMENTS?
COUNTRY
CALL
OR VISIT US ONLINE AT
WRITE
IN THE US
1-800-SAMSUNG
(7267864)
www.samsung.com/us
Samsung Electronics America, Inc.
85 Challenger Road Ridgefield Park,
NJ 07660-0511
Code No. AH68-02334S
HW-D7000_XAA_0321.indd 87
2011-03-21
2:02:41
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement