Samsung 211MP, LW24R15W User's manual

Samsung 211MP, LW24R15W User's manual
LCD TV
LW24R15W
Owner’s Instructions
Before operating the unit,
please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PC DISPLAY
PICTURE IN PICTURE (PIP)
PICTURE BY PICTURE (PBP)
TELETEXT
Caution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO PREVENT ELECTRICAL SHOCK, DO NOT
REMOVE REAR COVER, NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
WARNING:
The lightning flash and arrow head
within the triangle is a warning
sign alerting you of “dangerous
voltage” inside the product.
The exclamation point within the
triangle is a warning sign alerting
you of important instructions
accompanying the product.
TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
☛ The main voltage is indicated on the rear of your set and the frequency is 50 or 60 Hz.
Information in this document is subject to change without notice.
© 2002 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly
forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material.
The Samsung logo is the registered trademarks of Samsung Electronics Co., Ltd.; VESA, DPMS and DDC are
registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and logo are registered
trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Samsung Electronics Co.,
Ltd. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. All other product
names mentioned herein may be the trademarks or registered trademarks of their respective owners.
European Notice
Products with the CE Marking comply with both the EMC Directive (89/336/EEC), (92/31/EEC), (93/68/EEC) and the
Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these
directives implies conformity to the following European Norms:
■
EN55022:1998+A1:2000 - Radio Frequency Interference
■
EN55024:1998 - Electromagnetic Immunity
■
EN55013:1990+A12:1994+A13:1996+A14:1999 - Radio Frequency Interference
■
EN55020:1994+A11:1996+A12/A13/A14:1999 - Electromagnetic Immunity
■
EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics
■
EN61000-3-3:1995 - Voltage Fluctuations
■
EN60065:1997 or EN60095:1998 - Product Safety
English-2
Safety Instructions
These illustrations represent precautions concerning your TV.
10%
75%
40°
H
H
5°
œ Do NOT expose the TV to extreme
temperature conditions or to extreme
humidity conditions.
Do NOT expose the TV to direct
sunlight. √
œ Do NOT expose the TV to any
liquids.
If the TV is broken, do not try to √
repair it yourself. Contact qualified
service personnel.
œ During a storm conditions (especially
when there is lightning) unplug the
TV from the mains socket and aerial.
Keep all power adaptors apart. √
Possible fire hazard.
œ Always keep the power adaptor in a
well-ventilated area.
Remove and discard the plastic √
cover from the power adaptor before
use. Possible fire hazard.
œ Keep the power adaptor away from
any other heater. Possible fire hazard.
If the remote control is not used for a √
long period of time, remove the
batteries and store it in a cool, dry
place.
THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS
English-3
Contents
◆ FOREWORD
■
■
Caution ..........................................................................................................
Safety Instructions ..........................................................................................
◆ CONNECTING
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
English-4
THE
THE
6
7
8
9
9
10
10
10
10
11
12
13
14
14
15
16
CHANNELS
Storing Channels Automatically......................................................................
Storing Channels Manually.............................................................................
Giving Channels Names.................................................................................
Skipping Unwanted Channels ........................................................................
Fine Tuning Channel Reception......................................................................
Sorting the Stored Channels ...........................................................................
◆ USING
■
PREPARING YOUR TV
Viewing the Control Panel..............................................................................
Installing on the Wall .....................................................................................
Viewing the Connection Panel .......................................................................
- Connecting an Aerial or Cable Television Network.....................................
- Connecting Computer.................................................................................
- Connecting DTV Set-Top Box, VCR, or DVD ..............................................
- Connecting External A/V Devices ...............................................................
- Connecting External Speakers .....................................................................
- Connecting Speakers...................................................................................
Viewing Pictures From External Sources .........................................................
Viewing the Remote Control (All Functions Except Teletext)...........................
Viewing the Remote Control (Teletext Functions) ...........................................
Inserting the Batteries in the Remote Control..................................................
Switching On and Off ....................................................................................
Becoming Familiar with the Remote Control..................................................
Choosing Your Language ................................................................................
◆ SETTING
■
AND
2
3
17
18
19
20
20
21
VARIOUS FUNCTIONS
Changing the Picture Standard .......................................................................
Adjusting the Picture Settings .........................................................................
Selecting the Picture Format...........................................................................
Freezing the Current Picture...........................................................................
Changing the Sound Standard ........................................................................
Adjusting the Sound Settings ..........................................................................
Enjoying the Dolby Sound..............................................................................
22
22
23
23
24
24
25
Contents
◆ USING
■
■
■
■
■
■
◆ USING
■
■
■
■
■
■
■
■
■
■
■
■
VARIOUS FUNCTIONS
THE
THE
25
26
27
28
29
29
PC FUNCTIONS
Adjusting the Brightness and Contrast ............................................................
Selecting the Image Size.................................................................................
Adjusting the Image Quality...........................................................................
Changing the Image Position..........................................................................
Adjusting the Color ........................................................................................
Initializing the Image Settings.........................................................................
Display Modes ...............................................................................................
PowerSaver ....................................................................................................
◆ USING
■
THE
Switching the Internal Speakers On/Off..........................................................
Choosing the MTS (Multichannel Television Stereo) .......................................
Viewing the Picture In Picture (PIP) ................................................................
Viewing the Picture By Picture (PBP; Double Screen).....................................
Switching Off Automatically...........................................................................
Displaying Information...................................................................................
30
30
31
31
32
32
33
33
TELETEXT FEATURE
Teletext Feature ..............................................................................................
Displaying the Teletext Information ................................................................
Selecting a Page by Number ..........................................................................
Using FLOF to Select a Page ..........................................................................
Storing Teletext Pages .....................................................................................
34
34
35
36
36
◆ RECOMMENDATIONS FOR USE
■
■
■
Troubleshooting: Before Contacting Service Personnel ...................................
Technical and Environmental Specifications...................................................
Wiring the Mains Power Supply Plug (UK Only) ............................................
Symbols
Press
☛
➢
Important
Note
37
38
39
English-5
Viewing the Control Panel
Power Indicator
Remote Control Sensor
ΠSource
Displays a menu of all of the available input
sources (TV/Video/S-Video/DVD/DTV/PC).
Ø -› CH ‚+
Moves the selector up or down on the OSD.
Increases or decreases the channel number.
´ PIP
Activates PIP (Picture-In-Picture)
∏ -Š VOL ¥+
Moves the selector left or right on the OSD.
Increases or decreases the level of audio volume
and the values of the selected function.
ˇ PBP
Activates PBP (Picture-By-Picture).
¨ Menu
Opens the OSD and selects the function.
” Auto
Allows you experience the quality of displayed
picture. The values of fine, coarse and position are
adjusted automatically. (It works PC mode only.)
ˆ Exit
Exit from the on-screen menu.
’
English-6
(Power)
Turns ON/OFF your set.
Installing on the Wall
1
Removing the Stand
Using a hexagonal wrench, remove the stand.
2
Removing Rubbers
Remove the four rubbers from the edges.
3
Mounting on the Wall
Mount the stand on the wall using screws or nails.
4
Fixing the Set
Using a hexagonal wrench, fix your set into the stand.
☛
Installation Notes
◆ Do not install your set on any place other than vertical
walls.
◆ To protect the performance of your set and prevent
troubles, avoid the followings:
- Do not install next to smoke and fire detectors.
- Do not install in an area subjected to vibration or high
voltage.
- Do not install in the wall.
- Do not install near or around any heating apparatus.
◆ Use only recommended parts and components.
English-7
Viewing the Connection Panel
SPK (R)
L
R
S-VIDEO
AUDIO OUT
VIDEO
AUDIO (L) AUDIO (R)
AV JACK
5
6
4
DC POWER
PC
AUDIO (ST)
VIDEO
RF
SCART
SPK (L)
6
7
1
3
2
Power Input
you connect an audio or video system to your set,
☛ Whenever
ensure that all elements are switched off. Refer to the
documentation supplied with your equipment for detailed
connection instructions and associated safety precautions.
English-8
Viewing the Connection Panel (continued)
ΠConnecting an Aerial or Cable Television Network (depending on the model)
To view television channels correctly, a signal must be received by the set from one of the following sources:
- An outdoor aerial
- A cable television network
- A satellite network
´ Connecting Computer
- Connect the 15 Pin D-SUB connector to the PC video connector.
- Connect the stereo audio cable to ”Audio (ST)” on the rear of your set and the other end to “Audio Out” of
the sound card on your computer.
- If necessary, please install monitor driver contained on the accompanied CD. For more information, refer to
the driver installation instructions included with your CD package.
➣
Pin
15 Pin D-SUB connector
Separate H/V
Composite H/V
Sync-on-green
1
Red (R)
Red (R)
Red (R)
2
Green (G)
Green (G)
Green (G) + Horizontal/Vertical sync.
3
Blue (B)
Blue (B)
Blue (B)
4
Grounding
Grounding
Grounding
5
Grounding (DDC)
Grounding (DDC)
Grounding (DDC)
6
Red (R) Grounding
Red (R) Grounding
Red (R) Grounding
7
Green (G) Grounding
Green (G) Grounding
Green (G) Grounding
8
Blue (B) Grounding
Blue (B) Grounding
Blue (B) Grounding
9
No connection
No connection
Not used
10
Sync Grounding
Sync Grounding
Sync Grounding
11
Grounding
Grounding
Grounding
12
Data (DDC)
Data (DDC)
Data (DDC)
13
Horizontal sync.
Horizontal/Vertical sync.
Not used
14
Vertical sync.
Not used
Not used
15
Clock (DDC)
Clock (DDC)
Clock (DDC)
English-9
Viewing the Connection Panel
ˇ Connecting DTV Set-Top Box, VCR, or DVD
- Connect the DTV, VCR, or DVD SCART cable to the SCART connector of the DTV, VCR, or DVD.
- If you wish to connect both the DTV Set-Top Box and VCR (or DVD), you should connect the DTV Set-Top
Box to the VCR (or DVD) and connect the VCR (or DVD) to your set.
¨ Connecting External A/V Devices
- Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD, or Camcorder.
- Connect RCA audio cables to “AUDIO (L)” and “AUDIO (R)” on the rear of your set and the other ends to
corresponding audio out connectors on the A/V device.
- Headphone may be connected to the headphone output (∏) on the rear of your set. While the headphone is
connected, the sound from the built-in speakers will be disabled.
ˆ Connecting External Speakers
Connect RCA audio cables to amplifier built-in speakers (to take full advantage of the Surround sound effect).
Ø Connecting Speakers (depending on the model)
or
English-10
Viewing Pictures From External Sources
Once you have connected up your various audio and video systems,
you can view the different sources by selecting the appropriate input.
1
2
Check that all the necessary connections have been made (refer to
pages 8 and 9 for further details).
Switch your set on and if necessary, press the SOURCE button
repeatedly. The input sources are displayed in the following order:
Ant (TV) - Scart - Video - S-Video - PC.
Power
SOURCE
AUT
UTO
DISPLA
DISPLAY
STILL
P.STD
.STD
S.STD
.STD
MUTE
EXIT
PRE-CH
-/--
TTX/MIX
V.DOLBY
HOLD
DUAL I/II LIST/FLOF
SLEEP
SUBPAGE
P.SIZE
PBP
SIZE
CANCEL
PIP
ON
English-11
LOCATE
Viewing the Remote Control (All Functions Except Teletext)
Self-adjust to the incoming
video signal
Power
er
Television On/Off
SOURCE
AUTO
DISPLAY
STILL
Available sources selection
Display the setting information
Picture freeze
P.STD
.STD
S.STD
.STD
Picture effect selection
Sound effect selection
Next channel
Menu display and
change confirmation
P
MENU
Volume decrease
Volume increase
P
Previous channel
MUTE
EXIT
Temporary sound switch-off
Numeric buttons for
direct channel access
Exit from the OSD
1
2
3
4
5
6
7
8
9
PRE-CH
-/--
One/Two-digit channel selection
Previous channel
0
TTX/MIX
V.DOLBY
.DOLBY
Virtual Dolby menu display
Sound mode selection
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
.SIZE
PBP
Automatic switch-off
Picture size selection
SIZE
CANCEL
PIP
ON
PIP size selection
Picture-In-Picture On/Off
LOCATE
LOCA
PIP location selection
Picture-By-Picture
(Double screen)
➣
English-12
The performance of the remote control may be affected by bright light.
Viewing the Remote Control (Teletext Functions)
Power
er
SOURCE
AUT
UTO
DISPLA
DISPLAY
P.STD
STILL
S.STD
.STD
Teletext next page
Programme selection by name
P
MENU
P
Teletext previous page
MUTE
EXIT
1
2
3
4
5
6
7
8
9
PRE-CH
-/-0
Teletext display/
mix both teletext information
and the norma l broadcast
Teletext hold
Teletext reveal
TTX/MIX
V.DOLBY
.DOLBY
HOLD
DUAL
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
.SIZE
PBP
Teletext store
Teletext sub-page
SIZE
CANCEL
PIP
Teletext mode selection
(List or Flof)
Teletext cancel
ON
LOCATE
LOCA
Teletext size selection
Fastext topic selection
English-13
Inserting the Batteries in the Remote Control
You must insert or replace the batteries in the remote control when
you:
◆ Purchase your set
◆ Find that the remote control is no longer operating
correctly
1
Remove the cover on the rear of the remote control by pressing the
symbol downwards and then pulling firmly to remove it.
2
Insert two R03, UM4, “AAA” 1.5V or equivalent batteries taking care to
respect the polarities:
◆ + on the battery against + on the remote control
◆ - on the battery against - on the remote control
3
Replace the cover by aligning it with the base of the remote control
and pressing it back into place.
➣
Do not mix battery types, i.e. alkaline and monganese.
Switching On and Off
The mains lead is attached to the rear of your set.
☛
Power
SOURCE
AUT
UTO
DISPLA
DISPLAY
P.STD
.STD
If you have purchased this set in the United Kingdom, refer to
page 39 for further instructions on plug wiring.
STILL
S.STD
.STD
Plug the mains lead into an appropriate socket.
The screen is turned on and a green Standby indicator appears
Result:
on the front of your set.
Your set can be placed in Standby mode, in order to reduce the power
consumption.
The Standby mode can be useful when you wish to interrupt viewing
temporarily (during a meal, for example).
MUTE
EXIT
PRE-CH
-/--
TTX/MIX
V.DOLBY
HOLD
DUAL I/II LIST/FLOF
SLEEP
SUBPAGE
P.SIZE
PBP
SIZE
CANCEL
PIP
ON
English-14
LOCATE
1
Press the Power ( ) button on the remote control or the front of your
set.
The screen is turned off and a green Standby indicator
Result:
disappears on the front of your set.
2
To switch your set back on, simply press the Power ( ) button again.
➣
Do not leave your set in Standby mode for long periods of time
(when you are away on holiday, for example). Turn your set off by
unpluging from the mains and aerial.
Becoming Familiar with the Remote Control
The remote control is used mainly to:
◆ Change channels and adjust the volume
◆ Set up your set using the on-screen menu system
Power
Power
Power AUTO
SOURCE
DISPLAY
AUT
UTO
DISPLA
DISPLAY
Button
S.STD
▲
P
Viewing Function
Menu Function
Used to display the next
stored channel.
Used to select the previous
menu option.
P
▼
MUTE
EXIT
EXIT
SOURCE
Used to display the
previous stored channel.
Used to select the next menu
option.
AUTO
PRE-CH
P.STD
MENU
DISPLAY
STILL
P
MUTE
EXIT
Used to switch repeatedly between the last two channels
displayed. (PRE-CH; Previous Channel)
1
2
3
Used to display the corresponding channels.
4
5
6
7
8
S.STD
PRE-CH
-/--
to
0
9
PRE-CH
V.DOLBY
-/-TTX/MIX
-/--
TTX/MIX DUAL I/II LIST/FLOF
HOLD
AUTO
S.STD
.STD
P
Power
MUTE
V.DOLBY
CANCEL
HOLD SUBPAGE
DUAL I/II SIZE
LIST/FLOF PIP
CANCEL
SLEEP
DISPLAY
SLEEP
P.SIZE
STILL
ON
SUBPAGE
PBP
Used to select a channel numbered ten or over.
Press this button, and the “--” symbol is displayed.
Enter the two-digit channel number.
PBP
0
SIZE LOCATE
PIP
LOCATE
S.STD
TTX/MIX
Used to decrease the
volume.
Power
MUTE
EXIT
SOURCE
Used to increase the
volume.
P.STD
UTE
EXIT
➣
-/--
TTX/MIX
MENU
EXIT
Used to...
◆ Display a submenu containing
selections for the current
menu option.
Power◆ Search forwards manually
for channels
◆ Reduce a menu option value.
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
V.DOLBY
.DOLBY
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
.SIZE
PBP
SIZE
STILL
Used to...
◆ Display a submenu containing
P.STD
S.STD
selectionsS.STD
for the current
menu option.
◆ Search backwards manually
for channels
◆ Increase a menu option value.
To turnPRE-CH
the sound back on, press this button again, or
press the
- or
+ button.
V.DOLBY
Used to display
the
on-screen menu system.
DUAL I/II LIST/FLOF
Used to return to the previous
menu or normal viewing.
CANCEL
MUTE
MUTEsystem and return
EXITto normal
EXIT
Used to exit from
the menu
viewing directly.
-/--
PRE-CH
SLEEP SUBPAGE
X/MIX
V.DOLBY
P.SIZE
PBP
SIZE
PIP
ON
OLD
DUAL I/II LIST/FLOF
EEP
SUBPAGE
SIZE
LOCATE
CANCEL
PIP
ON
-/--
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
CANCEL
-/--
LOCATE
TTX/MIX
HOLD
TTX/MIX
CANCEL
PIP
ON
Used to switch the sound off temporarily.
MUTE
HOLD
9
PRE-CH
-/--
ON
P.SIZE
PBP
STILL
DISPLAY S.STD
STILL
AUTO
P.STD
STD
SIZE
SOURCE
STILL
P.STD
.STD
P.STD
SOURCE
ower
URCE
The following table presents the most frequently used buttons and
their functions.
English-15
LOCATE
LOCA
TE
Choosing Your Language
Power
SOURCE
AUTO
DISPLAY
P.STD
.STD
Power
STILL
S.STD
.STD
Power
When you start using your set for the first time, you must select the
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILLmenus
STILL
language which
will be
used for
displaying
and indications.
Power
P
1
MENU
P.STD
Press the
MENU P.STD
button.
Result:
S.STD
The main menu is displayed.
Power
S.STD
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
S.STD
S.STD
EXIT
EXIT
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
P
2
MUTE
EXIT
Function
Sleep Timer
¥ Off Š
PIP
Š
PBP
Š
PRE-CH
-/-Language
¥ English Š
TTX/MIX
Result:
DUAL I/II LIST/FLOF
SLEEP
SUBPAGE
SIZE
CANCEL
P.STD
The options available in the Function group are
displayed.
3
Press the
4
Press the P▼ or P▲ button to select the Language.
5
Select a particular language by pressing the
repeatedly.
MUTE
MUTE
EXIT
EXIT
6
When you are satisfied with your choice, press the EXIT button to
return to normal viewing.
V.DOLBY
HOLD
Press the P▼ or P▲ button to select the Function.
P.STD
- or
+ button.
MUTE
PIP
- or
+ button
MUTE
ON
P.SIZE
PBP
LOCATE
-/--
TTX/MIX
HOLD
-/--
TTX/MIX
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
-/--
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
CANCEL
TTX/MIX
SLEEP
P.SIZE
SUBPAGE
SLEEP SUBPAGE
SIZE
P.SIZE
PBP
PBP
SIZE
PIP
PIP
ON
HOLD
ON
LOCATE
LOCATE
SLEEP
P.SIZE
English-16
-/--
TTX/MIX
DUAL
HOLD
I/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
SUBPAGE
SLEEP
P.SIZE
PBP
SUBPAGE
SIZE
PBP
CANCEL
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
Storing Channels Automatically
You can scan for the frequency ranges available to you (and
Power Power
availability depends on your country). Automatically allocated
programme numbers may not correspond to actual or desired
programme numbers.
However
you can
sort numbers
SOURCE SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL manually and
PoweryouPower
clear any channels
do not wish to watch.
1
P.STD
SOURCE
Press the MENU button.
Result:
2
P.STD
SOURCE
AUTO
S.STD
DISPLAY
STILL
P.STD
S.STD
STILL
Power
Power
S.STD
S.STD
The main menu is displayed.
P.STD
Result:
SOURCE
+ button. P.STD
P.STD
S.STD
Country
Search
¥
Š
Country
Search
¥
Š
SOURCE
AUTO
DISPLAY
AUTO
- or
DISPLAY
STILL
STILL
+ button again.
MUTE available in the
EXITAuto EXIT
Result: MUTEThe options
store group are
P.STD
S.STD
S.STD
displayed with the Country is selected.
Channel
5
Select your country by pressing the
- or
+ button repeatedly.
MUTE
MUTE
EXIT
The following
countries
are available:EXIT
Belgie - Deutschland - Espania - France - Italia - Nederland
- Schweiz - Sverige - UK - East Europe.
6
Press the P▼ or P▲ button to select
MUTEthe Search,
MUTE and then press
EXIT the EXIT
- or
+ button.
➣
7
Search
Program
Frequency
Band
The search will end automatically. Channels are sorted
PRE-CH
-/-and stored
in an order PRE-CH
which reflects
their position in the
frequency range, (with lowest first and highest last). The
programme originally selected is then displayed.
-/--
MUTE
TTX/MIX
TTX/MIX
EXIT
EXIT
V.DOLBY
UK
1
205MHz
VHF-H
V.DOLBY
PRE-CH PRE-CH
-/--/-To stop
the search
before it has
finished, press the EXIT button.
HOLD
DUAL
HOLD
I/II LIST/FLOF
DUAL
LIST/FLOF
CANCEL
CANCEL
When the
channels
have
beenI/IIstored,
you can:
TTX/MIXchannels
TTX/MIX
V.DOLBY V.DOLBY
◆ Change
◆ Assign a name to the stored channels
(refer
-/--/-- to page 19)PRE-CH PRE-CH
SLEEP
SUBPAGE
SLEEP
SUBPAGE
SIZE
SIZE
PIP
PIP
◆ Clear
a channel
(refer
to
page 20)
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
◆ Fine tune channel reception if necessary
(refer
to page 20)
ON
ON
◆ Sort them in the order required
(refer
to
page
21)
TTX/MIX TTX/MIX
V.DOLBY V.DOLBY
P.SIZE
SLEEP
-/--
TTX/MIX
-/-P.SIZE
P.SIZE
PBP
PBP
SUBPAGE
SLEEP SUBPAGE
SIZE
P.SIZE
PBP
TTX/MIX
V.DOLBY
SLEEP SUBPAGE
SLEEP SUBPAGE
SIZE
V.DOLBY
SLEEP
SUBPAGE
SLEEP SUBPAGE
SIZE
PBP
LOCATE
PIP
ON
ON
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
PRE-CH
LOCATE LOCATE
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
P.SIZE
PBP
LOCATE
SIZE
PIP
PRE-CH
PBP
HOLD
P.SIZE
Š
S.STD
P.STD
MUTE
UK
The Auto store is selected.
Press the
Result:
Š
Š
Š
Š
Š
Š
Channel
Press the P▼ or P▲ button to select
the Channel.
SOURCE SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
Result:
The options available in the Channel group are displayed.
Power - or
3 Power
Press the
4
DISPLAY
AUTO
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Channel sort
P.SIZE
CANCEL
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
P.SIZE
PBP
PBP
CANCEL
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
English-17
Š
Storing Channels Manually
Channel
Š
Š
Š
Š
Š
Š
Auto store
Manual store
Name
Add/Erase
Fine tune
Channel sort
You can store up to 100 channels, including those received via cable
Power
Power
networks. When
storing
channels manually, you can choose:
◆ Whether or not to store each of the channels found
◆ The
programme
channel which you
SOURCE
SOURCE
AUTO number
DISPLAY
AUTO of each
DISPLAY
STILL stored
STILL
Power
Power
wish to identify
SOURCE
1
Channel
Color system
Sound system
Search
Channel
Program
Store
¥ AUTO Š
¥
BG
Š
Š
0MHz
C 1
P 1
?
Channel
¥ AUTO Š
¥
BG
Š
Š
0MHz
C 1
P 1
?
Color system
Sound system
Search
Channel
Program
Store
P.STD
SOURCE
AUTO
Channel
Color system
Sound system
Search
Channel
Program
Store
S.STD
STILL
S.STD
PowerP.STDPower
Result:
The main menu
is displayed.
P.STD
S.STD
S.STD
2
Press the P▼ or P▲ button to select the Channel.
SOURCE
Result:
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
The options available in the Channel group are displayed.
3
Press
P.STD the P.STD- or
4
Press the P▼ or P▲ button to select the Manual store. Press the
SOURCE SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
- or
+ button.
Result:
5
+ button.
S.STD
Power
S.STD
Power
The options available in the Manual store group are
MUTE
EXIT
displayed
with the ColorEXIT
system
selected.
P.STD is P.STD
S.STD
MUTE
STILL
S.STD
Power
Power
If necessary,
indicate
the broadcasting standard required by pressing
EXIT
the MUTE
- or
+ button EXIT
repeatedly.
MUTE
Result:
¥ AUTO Š
¥
BG
Š
Š
0MHz
C 1
P 1
?
DISPLAY
STILL
Press the MENU button.
The color
standards
inSTILL
thePower
followingPower
order:
SOURCE
SOURCE
AUTO
DISPLAY
AUTOare displayed
DISPLAY
STILL
AUTO - PAL - SECAM - NT4.43.
Channel
Color system
Sound system
Search
Channel
Program
Store
P.STD
DISPLAY
AUTO
6
SOURCEIndicate
SOURCE
AUTO the DISPLAY
AUTO
DISPLAY
STILL
P.STDor P▲P.STD
S.STD
Press the P▼
button to select the
SoundS.STD
system.
MUTE
MUTE
EXIT
EXIT
sound
standard
required by pressing
the
- or
+ button
repeatedly.
P.STD
P.STD
S.STD
PRE-CH PRE-CH
-/-Result: -/--The sound
standards are
displayed in the following order:
BG - DK - I - L.
Power Power
7
¥ AUTO Š
¥
BG
Š
Š
0MHz
C 1
P 1
?
MUTEV.DOLBY
MUTE
-/-TTX/MIX
If you know
the TTX/MIX
channelPRE-CH
number PRE-CH
toV.DOLBY
be stored,
press
the P▼ or P▲ EXIT
button to select the Channel. Indicate the
required
number
by
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
pressing the
Power - or
Power + button.
-/--
TTX/MIX
HOLD
TTX/MIX
DUAL
HOLDI/II V.DOLBY
LIST/FLOF
DUAL I/II V.DOLBY
LIST/FLOF
CANCEL
S
S
EXIT
STILL
CANCEL
If you do not know the channel numbers,P.STD
press the
P▼ or P▲ button
P.STD
S.STD
to select the Search. Start the search by pressing the
- or
PRE-CH
PRE-CH
-/-- SLEEP
-/-SOURCE
SOURCE
AUTO
DISPLAY
AUTOCANCEL
DISPLAY
STILL PIPSTILL
SUBPAGE
SLEEP
SUBPAGE
SIZE
SIZE
PIP
HOLD
DUAL
HOLD
I/II LIST/FLOF
DUAL
I/II
LIST/FLOF
CANCEL
+button.
ON
ON
MUTE
MUTE
EXIT
The tuner
scans the frequency
rangeEXIT
until the first
P.STD
P.STD
S.STD
S.STD
P.SIZE
P.SIZE
PBPor theSIZE
PBP
TTX/MIX
TTX/MIX
V.DOLBYLOCATE
V.DOLBY
SLEEP
SUBPAGE
SLEEP
SUBPAGE
SIZE
PIP
PIP
channel
channel
that
you LOCATE
selected is received on
your screen. ON
ON
MUTE
MUTE
PRE-CH
-/--/-HOLD
DUAL
HOLD
I/II
LIST/FLOF
DUAL
I/II
LIST/FLOF
CANCEL
CANCEL
LOCATE
P.SIZE
P.SIZE
PBPa programme
PBP
To assign
number toLOCATE
a channel, select the Program by
S.STD
Result:
Channel
¥ AUTO Š
¥
BG
Š
Š
0MHz
C 1
P 1
?
Color system
Sound system
Search
Channel
Program
Store
8
Channel
¥ AUTO Š
¥
BG
Š
Š
0MHz
C 1
P 1
OK
English-18
E
pressing the P▼ or P▲ button. Press the
- or
+ button to
find
the correct
number.
TTX/MIX
TTX/MIX
V.DOLBY V.DOLBY
SLEEP SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
PIP
9
Color system
Sound system
Search
Channel
Program
Store
EXIT
PRE-CH
ON
Press the P▼ or P▲ button toON
select the
Store. Select the OK by
pressing
the
or
+
button.
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
LOCATE LOCATE
P.SIZE
P.SIZE
PBP
PBP
Result:
10
MUTE
MUTE
EXIT
The
programme
PRE-CH
PRE-CH number are
-/-- channel
-/-- and associated
stored.
SLEEP SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
-/-- ON
-/-Repeat Steps
7 to TTX/MIX
9 for each channelV.DOLBY
to be stored.
TTX/MIX
V.DOLBY
MUTE
MUTE
EXIT
P.SIZE
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
SLEEP
SUBPAGE
SLEEP SUBPAGE
SIZE
P.SIZE
-/--
P.SIZE
PBP
-/--
PBP
SIZE
PIP
ON
-/-LOCATE
EXIT
P.SIZE
PBP
TTX/MIX
CANCEL
PIP HOLD
ON
-/-LOCATESLEEP
TTX/MIX TTX/MIX
PRE-CH PRE-CHP.SIZE
PBP
LOCATE
TTX/MIX
EXIT
PIP
ONPRE-CH
PR
LOCATE
V.DOLBY
V.D
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
CA
PRE-CH PRE-CH
SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
ON
V.DOLBY V.DOLBY
LOCATE
P.SIZE
PBP
PBP
LO
Giving Channels Names
Power
Power
If channel name information is broadcast when you store the channels
either manually or automatically, the names are assigned Power
to the
SOURCE
AUTOhowever
DISPLAY
AUTO change
DISPLAY
STILL these
STILL
channels
directly.
YouSOURCE
can
names or assign new
Power
names as required.
SOURCE
P.STD
AUTO
SOURCE
1
P.STD
DISPLAY
AUTO
DISPLAY
S.STD
Press the MENU button.
Result:
P.STD
P.STD
S.STD
Power
Press the P▼ or P▲ button to select the Channel.
Channel
Result:SOURCE
The SOURCE
options
the
AUTO available
DISPLAY
AUTO inDISPLAY
STILLChannel
STILLgroup are displayed.
3
Press the
Power
- or
P.STD
4
5
Power
+ button.
P.STD
S.STD
S.STD
Press the SOURCE
P▼ or P▲
button DISPLAY
toAUTO
select DISPLAY
the
Name. Press
SOURCE
AUTO
STILL
STILL the
+ button.
Result:
P
P
P
P
1
2
3
4
S.STD EXIT
S.STD
EXIT
Press the
7
Press the P▼ or P▲ button to select a letter (A~Z), a number(0~9)
or a symbol (-, space). Move on the previous or next letter by
pressing the
- or
+ button.
8
Repeat Steps 5 to 7 for each channel to be assigned to a new
PRE-CH PRE-CH
-/-name. -/--
- or
MUTE
+ button.
MUTE
EXIT
MUTE
MUTE
TTX/MIX TTX/MIX PRE-CH
EXIT
EXIT
V.DOLBY V.DOLBY
DUAL
HOLDI/II V.DOLBY
LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
HOLD
SLEEP
SUBPAGE
SLEEP CANCEL
SUBPAGE
SIZE
SIZE
PIP
DUAL
I/II LIST/FLOF
PRE-CH
-/--/-ON
SLEEP
P.SIZE
SUBPAGE
TTX/MIX
-/-PBP
HOLD
PRE-CH
-/--
SLEEP
HOLD
P.SIZE
SLEEP
P.SIZE
TTX/MIX
HOLD
DUAL I/II LIST/FLOF
SLEEP
SUBPAGE
CANCEL
PIP
PRE-CH
ON
V.DOLBY
SUBPAGE
SLEEP SUBPAGE
SIZE
V.DOLBY
CANCEL
LOCATE LOCATE
P.SIZE
PBP
PBP
SIZE
PIP
TTX/MIX
V.DOLBY
V.DOLBY
ON
PRE-CH PRE-CH
-/-LOCATE
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
TTX/MIX
A
EXIT
TTX/MIX
HOLD
Channel
EXIT
EXIT
6
P.SIZE
1
2
3
4
- or
If necessary, select the channel to be assigned to a new name by
MUTE
pressing the P▼ or P▲ button.
TTX/MIX
P
P
P
P
The current channels are displayed.
P.STD MUTE
P.STD
MUTE
MUTE
-/--
Š
Š
Š
Š
Š
Š
The main menu
is displayed.
S.STD
Power
2
S.STD
STILL
Channel
Auto store
Manual store
Name
STILL Add/Erase
Fine tune
Channel sort
SIZE
PIP
SIZE
PIP
ON
P.SIZE
PBP
LOCATE
V.DOLBY
PIP
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL ON
CANCEL
ON
P.SIZE
PBP
PBP
LOCATE
SUBPAGE
SLEEP SUBPAGE
SIZE
P.SIZE
PBP
PBP
LOCATE
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
English-19
Skipping Unwanted Channels
You can exclude the channels you chosen from the channels you
scanned. When you scan through the stored channels, those you have
Power Power
chosen to skip are not displayed.
Channel
Auto store
Manual store
Name
Add/Erase
Fine tune
Channel sort
Š
Š
Š
Š
Š
Š
Power
All channels
that
you SOURCE
do
not specifically
choose STILL
to skip are displayed
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
Power
during scanning.
SOURCE
SOURCEP.STDAUTO P.STD
DISPLAY
1
P
P
P
P
1
2
3
4
Added
Added
Added
Added
2
Result:
DISPLAY
Power P.STD
S
AUTO
DISPLAY
SOURCE
AUTO
DISPLAY
4
Channel
P
P
P
P
1
2
3
4
The options available in the Channel group are displayed.
Press the
P.STD
- or
S.STD
+ S.STD
button.
Press the P▼ or P▲ button to select the Add/Erase. Press the
- or
+ button.
Result:
Erased
Added
Added
Added
The stored channels are displayed.
MUTE
MUTE
EXIT
EXIT
5
Press the P▼ or P▲ button to select the channel to add or erase.
MUTE
If necessary, select the Added or Erased by pressing the
- or
MUTE
EXIT
+ button.
6
Repeat Step 5 for each channel to be added or erased.
MUTE
MUTE
PRE-CH
-/--
PRE-CH
Fine Tuning Channel Reception
-/-- TTX/MIX
Power
PR
-/-PRE-CHV.DOLBY
TTX/MIX
V.DOLBY
TTX/MIX
Power
V.D
DUAL
HOLD
I/II do
LIST/FLOF
DUAL
I/II have
LIST/FLOF
CANCEL
CANCEL the channel,
If the reception
is clear,
you
not
to fine-tune
TTX/MIX HOLD
V.DOLBY
as this is done automatically during the search and store operation.
PRE-CH
-/-HOLD
DUAL I/II LIST/FLOF CA
If however
signal SOURCE
isAUTO
weakPRE-CH
or
distorted,
SOURCE
DISPLAY
AUTO
DISPLAY
STILLyou may
STILL have to fine-tune
-/-- the
SLEEP
SUBPAGE
SLEEP
SUBPAGE
SIZE
SIZE
PIP
PIP
HOLD
DUAL I/II LIST/FLOF CANCEL
the channel
manually.
Channel
Š
Š
Š
Š
Š
Š
ON
Power
P.STD
P.STD
S.STD
PBP SIZEV.DOLBY
PBP PIP LOCATE
TTX/MIX
SLEEP P.SIZE
SUBPAGEP.SIZE
Power
1
Press the MENU button.
SOURCE
Result:
SOURCE
AUTO
DISPLAY
AUTO
2
Fine tune
7
3
ON
DISPLAY
STILL
ON
S.STD
LOCATE
STILL
TTX/MIX SLEEP
SUBPAGE
HOLD P.SIZE
DUAL I/II PBP
LIST/FLOF
The main menu is displayed.
HOLDP.SIZEDUAL I/IIPBP
LIST/FLOF
English-20
EXIT
EXIT
-/--
Auto store
Manual store
Name
Add/Erase
Fine tune
Channel sort
STILL
STILL
P.STD
3
S
The main menu is S.STD
displayed.
Press the P▼ or P▲ button to select the Channel.
SOURCE
AUTO
S.STD
Press the MENU button.
Power
Result:
P.STD
Channel
STILL S.STD
SLEEP SUBPAGE
SLEEP
SUBPAGEThe options
SIZE
PIP
Result:
available
in the Channel group are displayed.
ON
P.SIZE
PBP
Press the
- or
+ button.
LOCATE
P.SIZE
PBP
4
Press the P▼ or P▲ button to select the Fine tune.
5
Obtain a sharp and clear picture and good sound quality by pressing
the
- or
+ button.
MUTE
MUTE
EXIT
EXIT
MUTE
-/--
EXIT
-/--
CANCELLO
CANCEL
LOCATE
Press
select the
Channel.
P.STD the P▼
P.STDor P▲ button toS.STD
S.STD
MUTE
V.DOLBY
SIZE
EXIT
PRE-CH
PRE-CH
SIZE
PIP
ON
LOCATE
Sorting the Stored Channels
You can exchange the numbers of two channels, in order to:
Channel
Power
Power order in which the channels have been
◆ Modify
the numeric
automatically stored.
◆ Give
easilySOURCE
remembered
SOURCE
AUTO
DISPLAY
AUTO numbers
DISPLAY
STILL to the
STILLchannels that you
Power
Power
watch most often.
P.STD
SOURCE
1
2
S.STD
DISPLAY
STILL
S.STD
STILL
Power
Result:Power
P.STDThe main
P.STD menu is displayed.
S.STD
S.STD
DISPLAY
AUTO
Press the MENU button.
Channel
From
To
Store
Press the P▼ or P▲ button to select the Channel.
SOURCE
SOURCE
AUTO
Result:
Power
3
P.STD
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
Power
- or
+ S.STD
button. S.STD
SOURCE
The options available in the Channel group are displayed.
Press the
P.STD
P.STD
SOURCE
AUTO
DISPLAY
STILL
AUTO
DISPLAY
Press the
P.STD
Result:
SOURCE
6
+ button.
P.STD
STILL
S.STD
S.STD
SOURCE
AUTO
The options available in the Channel sorting
group are
MUTE DISPLAY
MUTE
EXIT
EXIT
AUTO
displayed
withSTILL
the From is
selected.
DISPLAY
P.STD
Select the channel number that you wish to change by pressing the
S.STD
MUTE
EXIT
- orMUTE + button
repeatedly. EXIT
P.STD
STILL
Channel
From
S.STDTo
Store
P 1
P 3
?
From
To
Store
P 3
P 1
OK
Press the P▼ or P▲ button to select the To. Select the new number
by which you wish to identify the channel by pressing the
- or
+ button repeatedly.
MUTE
7
- or
P 1
P-?
Power
4 Power
Press the P▼ or P▲ button to select the Channel sorting.
5
Š
Š
Š
Š
Š
Š
Auto store
Manual store
Name
Add/Erase
Fine tune
Channel sort
MUTE
EXIT
EXIT
Press the P▼ or P▲ button to select the Store. Select the OK to
confirm the exchange of channel numbers by pressing the
- or
PRE-CH PRE-CH
-/--/-+ button.
MUTE
MUTE
Channel
EXIT
EXIT
Result:
The selected channel is exchanged with the one
chosen PRE-CH
number.
-/--previously
-/-- stored to thePRE-CH
TTX/MIX
TTX/MIX
V.DOLBY
V.DOLBY
8
MUTE
For all the channels to move to the required channel numbers,
EXIT
repeat TTX/MIX
steps
7 after
select
From byV.DOLBY
pressing the P▼ or P▲
HOLD 5 to
DUAL
HOLD
I/II LIST/FLOF
DUAL I/IIthe
LIST/FLOF
CANCEL
CANCEL
TTX/MIX
V.DOLBY
button.
EXIT
MUTE
-/--
TTX/MIX
-/-HOLD
TTX/MIX
-/-SLEEP
HOLD
-/-SLEEP
HOLD
PRE-CH
SUBPAGE
SLEEP
SUBPAGE
SIZEI/II PRE-CH
SIZE
PIP
DUAL
HOLDI/II LIST/FLOF
DUAL
LIST/FLOF
CANCEL
ON
PIP
CANCEL
ON
P.SIZE
TTX/MIX
SLEEP
LOCATE
P.SIZE
PBP
PBP
V.DOLBY
V.DOLBY
SUBPAGE
SLEEP
SUBPAGE
SIZE
SIZE
PIP
PRE-CH
ON
LOCATE
PIP
DUAL
HOLD
I/II LIST/FLOF
DUAL
I/II LIST/FLOF
CANCEL
P.SIZE
P.SIZE
PBP
PBP
V.DOLBY
PRE-CH
SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
DUAL I/II LIST/FLOF
TTX/MIX
P.SIZE
P.SIZE
PBP
PBP
CANCEL
ON
V.DOLBY
LOCATE
SLEEP
SUBPAGE
SIZE
PIP
HOLD
DUAL I/II LIST/FLOF
P.SIZE
PBP
SLEEP
SUBPAGE
CANCEL
ON
LOCATE
SIZE
PBP
LOCATE
TTX/MIX
-/--
PIP
HOLD
ON
TTX/MIX
LOCATE
SLEEP
HOLD
P.SIZE
SLEEP
V.DOLBY
PRE-CH
DUAL I/II LIST/FLOF
CANCEL
V.DOLBY
SUBPAGE
SIZE
DUAL I/II LIST/FLOF
PIP
CANCEL
ON
LOCATE
PBP
SUBPAGE
PIP
ON
P.SIZE
CANCEL
LOCATE
PRE-CH
-/--
ON
SIZE
PIP
ON
P.SIZE
PBP
LOCATE
LOCATE
English-21
Changing the Picture Standard
Power
Picture
Mode
¥
Brightness
Contrast
Sharpness
Color
Tint
¥
Size
Custom
Š
You can selectSOURCE
the type
of picture
best corresponds
to your
SOURCE
AUTO
DISPLAY
AUTOwhich
DISPLAY
STILL
STILL
Power Power
viewing requirements.
P.STD
1
Result:
DISPLA
DISPLAY
P.STD
.STD
S.STD
The main menu is displayed.
3
STILL
4
P
P.STD
Press the
- or
P.STD
DISPLAY
STILL
STILL
S.STD
S.STD
EXIT
EXIT
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
+ button.
The Mode is selected.
You can also set these options simply by pressing the P.STD
(Picture Standard) button.
MUTE
➣
EXIT
DISPLAY
AUTO
Select the required picture effect by pressing the
- or
+
button repeatedly. The following picture effects are available:
MUTE
EXIT
EXIT
Custom MUTE
- Standard
- Natural - Mild.
➣
MUTE
SOURCE
AUTO
The options available in the Picture group are displayed.
Result:
S.STD
.STD
S.STD
SOURCE
Press the P▼ or P▲ button to select the Picture.
Result:
Power
AUT
UTO
P.STD
Press the MENU button.
Š
Wide
2
SOURCE
Power
MUTE
On the Picture menu, if you change the Brightness, Contrast,
Sharpness, Color or Tint (NTSC only) settings, the Custom is
selected automatically.
-/--
-/--
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
-/--
PRE-CH
-/--
TTX/MIX
TTX/MIX
Adjusting the Picture Settings
TTX/MIX
V.DOLBY
HOLD
DUAL I/II LIST/FLOF
SLEEP
SUBPAGE
P.SIZE
PBP
CANCEL
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
Power
Power
TTX/MIX
SIZE
TTX/MIX
PIP
ON
Picture
LOCATE
Mode
¥
Brightness
Contrast
Sharpness
Color
Tint
¥
Size
-/--
Custom
Š
SLEEP settings
SUBPAGE
SLEEP
SUBPAGE
SIZE allow
SIZE
PIP
PIP
Your set has several
you to STILL
control picture
SOURCE
SOURCE
AUTO which
DISPLAY
AUTO
DISPLAY
STILL
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
ON
ON
quality.
Power Power
P.SIZE
P.STD
1
Š
2
Power
Power
LOCATE
S.STD
SLEEP
STILL
P.SIZE
P.STD
P.STD
S.STD
S.STD
SOURCE
AUTObutton
DISPLAY
AUTO
DISPLAY
STILL
STILL
Press the
P▼ orSOURCE
P▲
to select
the Picture.
SUBPAGE
SLEEP SUBPAGE
SIZE
P.SIZE
PBP
PBP
The options available in the Picture group are displayed.
P.STD
70
LOCATE
S.STD
The main menu is displayed.
Result:
Brightness
PBP
SOURCE
AUTO
AUTO
DISPLAY
STILL
Press the
MENUSOURCE
button. DISPLAY
Result:
Wide
P.SIZE
PBP
P.STD
P.STD
S.STD
S.STD
3
Press the
4
Select the option (Brightness, Contrast, Sharpness, Color or
Tint-NTSC only) to be adjusted by pressing the P▼ or P▲ button.
Press the
- or
+ button.
- or
+ button.
MUTE
EXIT
Result: MUTEThe horizontal
bar is displayed.
5
Press the
MUTE
➣
- or
MUTE
EXIT
+ button to reach the required setting.
EXIT
EXIT
If you make any changes to these settings, the picture standard is
automatically switched to Custom.
MUTE
MUTE
-/--
-/--
EXIT
EXIT
PRE-CH
PRE-CH
English-22
TTX/MIX
-/--
TTX/MIX
-/--
V.DOLBY V.DOLBY
PRE-CH PRE-CH
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
Power
SOURCE
AUTO
DISPLAY
P.STD
STILL
S.STD
Selecting the Picture Format
Power
Power
MUTE
You can selectSOURCE
the picture
which
best corresponds
to your
SOURCE
AUTOformat
DISPLAY
AUTO
DISPLAY
STILL
STILL
viewing requirements.
P.STD
1
Result:
2
P.STD
S.STD
S.STD
Press the MENU button.
The main menu is displayed.
Press the P▼ or P▲ button to select the Picture.
Result:
The options available in the Picture group are displayed.
3
Press the
4
Press the P▼ or P▲ button to select the Size.
5
Select the required picture format by pressing the
- or
+
button repeatedly.
The following picture
MUTE
MUTE
EXIT formats
EXITare available:
Wide - Normal 1 - Normal 2 - Zoom 1 - Zoom 2.
- or
+ button.
EXIT
Picture
Mode
¥
Brightness
Contrast
Sharpness
Color
-/--Tint
¥
Size
Custom
TTX/MIX
PRE-CH
Wide
V.DOLBY
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
.SIZE
PBP
SIZE
CANCEL
PIP
ON
➣
LOCATE
LOCA
TE
You can also select these options simply by pressing the
P.SIZE (Picture Size) button.
-/--
TTX/MIX
-/--
TTX/MIX
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
Freezing the Current Picture
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
CANCEL
SLEEP
SIZE
SIZE
PIP
PIP
Press the STILLSLEEP
buttonSUBPAGE
on the SUBPAGE
remote
control
to freeze
the picture on
ON
ON
a given frame.
To return to normal
viewing,
press
the LOCATE
STILL button
again.
LOCATE
P.SIZE
P.SIZE
PBP
PBP
Power
SOURCE
AUT
UTO
DISPLA
DISPLAY
STILL
P.STD
.STD
S.STD
.STD
MUTE
EXIT
PRE-CH
-/--
TTX/MIX
V.DOLBY
English-23
HOLD
DUAL I/II LIST/FLOF
SLEEP
SUBPAGE
P.SIZE
PBP
SIZE
Š
CANCEL
PIP
ON
LOCATE
Š
Changing the Sound Standard
Power
Sound
Mode
Bass
Treble
Dolby
Speaker
MTS
¥
Custom
Š
You can selectSOURCE
the type
of special
effect toSTILL
be used when
SOURCE
AUTO
DISPLAY
AUTOsound
DISPLAY
STILL
Power Power
watching a given broadcast.
P.STD
:
:
¥
Off
Off
Mono
1
AUT
UTO
DISPLA
DISPLAY
P.STD
.STD
3
STILL
4
P
S.STD
SOURCE
SOURCE
AUTO
P.STD
P.STD
- or
STILL
S.STD
S.STD
EXIT
EXIT
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
CANCEL
+ button.
The Mode is selected.
Select the required sound effect by pressing the
- or
+
button repeatedly. The following sound effects are available:
MUTE
EXIT
EXIT
Custom MUTE
- Standard
- Music - Movie
- Speech.
You can also set these options simply by pressing the S.STD
(Sound Standard) button.
MUTE
MUTE
EXIT
-/--
-/--
PRE-CH
PRE-CH
V.DOLBY
-/--
Adjusting the Sound Settings
Power Power
PRE-CH
-/--
TTX/MIX
HOLD
DISPLAY
STILL
The options available in the Sound group are displayed.
Press the
➣
MUTE
DISPLAY
AUTO
Press the P▼ or P▲ button to select the Sound.
Result:
S.STD
.STD
S.STD
The main menu is displayed.
Result:
Power
P.STD
Press the MENU button.
Result:
Š
2
SOURCE
Power
TTX/MIX
TTX/MIX
V.DOLBY
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
STILL
Power DISPLAY
Power
V.DOLBY
DUAL I/II LIST/FLOF
CANCEL
TTX/MIX
PIP
¥SIZE Custom
Bass
ON
P.SIZETreble
PBP
LOCATE
Dolby
Speaker
MTS
:
:
¥
STILL
HOLD canDUAL
HOLD
LIST/FLOF
DUAL I/IIto LIST/FLOF
CANCEL
The sound settings
be I/II
adjusted
suit
yourCANCEL
personal preferences.
Sound
SLEEP
Mode SUBPAGE
Off
Off
Mono
-/--
Š
1
P.STD
P.STD
SOURCE
SLEEP
SLEEP
SIZE
Power SUBPAGE
Power SUBPAGE
Press the MENU button.
Result:
2
ON
S.STD
DISPLAY
AUTO
PIP
HOLD
ON
The main menuP.STD
is displayed.
P.STD
P.SIZE
SOURCE
Š
S.STD
SOURCE
AUTO
SIZE
PIP
P.SIZE
PBP
SOURCE
AUTO
PBP
DISPLAY
AUTO
LOCATE
DISPLAY
STILL
TTX/MIX
DISPLAY
STILL
S.STD
LOCATE
STILL
SLEEP
Press the P▼ or P▲ button to select the Sound.
STILL
S.STD
SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
Result: P.STDThe options
the SoundS.STD
group are displayed.
P.STD available in S.STD
P.SIZE
Bass
P.SIZE
PBP
PBP
3
Press the
4
Select the option (Bass or Treble) to be adjusted by pressing the
P▼ or P▲ button. Press the
- or
+ button.
- or
+ button.
47
Result:
5
The horizontal bar is displayed.
MUTE
Press the
MUTE
- or
EXIT
+ button to reach the required setting.
MUTE
➣
EXIT
MUTE
EXIT
EXIT
If you make any changes to these settings, the sound standard is
automatically switched to Custom.
MUTE
MUTE
-/--
-/--
EXIT
EXIT
PRE-CH
PRE-CH
-/-V.DOLBY
V.DOLBY
English-24
TTX/MIX
HOLD
-/--
TTX/MIX
-/--
DUAL
HOLDI/II LIST/FLOF
DUAL
I/II LIST/FLOF
CANCEL
TTX/MIX
TTX/MIX CANCEL
PRE-CH PRE-CH
-/--
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
Enjoying the Dolby Sound
Power
Power
This feature provides
a AUTO
home theater-like
Dolby STILL
effect by mixing the
SOURCE SOURCE
DISPLAY
AUTO
DISPLAY
STILL
left and right speakers.
Power
1
Power
P.STD
SOURCE
SOURCE
AUTO
Result:
2
P.STD
S.STD
S.STD
Press the MENU button.
DISPLAY
AUTO
DISPLAY
STILL
STILL
The main menu is displayed.
Sound
Mode
Bass
Treble
Dolby
Speaker
MTS
¥
Mode
Bass
Treble
Dolby
Speaker
MTS
¥
:
:
¥
Custom
Š
On
Off
Mono
Š
Press the
to select
the Sound.
P.STD
P.STDP▼ or P▲ button
S.STD
S.STD
Result:
The options available in the Sound group are displayed.
3
Press the
4
Press the P▼ or P▲ button to select the Dolby.
5
For enjoying the Dolby sound effect, select the On by pressing the
- orMUTE + button.
MUTE
EXIT
EXIT
➣
MUTE
- or
+ button.
You can also select simply by pressing the V.DOLBY (Virtual
Dolby) button.
MUTE
EXIT
-/--
EXIT
PRE-CH
-/--
PRE-CH
Switching the Internal Speakers On/Off
TTX/MIX
Power TTX/MIX
Power
-/--
V.DOLBY
PRE-CH
-/--
V.DOLBY
PRE-CH
HOLD speakers
DUAL
HOLD
LIST/FLOF
DUAL
I/II LIST/FLOF
CANCEL
When the internal
switched
off, allCANCEL
the sound is routed to
SOURCE
SOURCE
AUTOI/II are
DISPLAY
AUTO
DISPLAY
STILL
STILL
the external speakers.
TTX/MIX
1
TTX/MIX
V.DOLBY V.DOLBY
PowerSLEEP
Power
SLEEP
SIZE
SIZE
PIP
PIP
P.STD SUBPAGE
P.STD SUBPAGE
S.STD
S.STD
ON
ON
Press the MENU button.
HOLD
DUAL
HOLD
I/II
LIST/FLOF
DUAL
I/II
LIST/FLOF
CANCEL
CANCEL
SOURCE P.SIZE
SOURCE
AUTO PBP
DISPLAY
AUTO LOCATE
DISPLAY
STILL LOCATE
STILL
P.SIZE
PBP
Result:
2
The main menu is displayed.
Sound
:
:
¥
SLEEP
SLEEP
SIZE
PIPto select
PIPthe
PressSUBPAGE
the P▼
orSIZE
P▲P.STD
button
Sound.S.STD
P.STDSUBPAGE
S.STD
ON
ON
Result:
P.SIZE
The options available in the Sound group are displayed.
P.SIZE
PBP
LOCATE
PBP
LOCATE
3
Press the
4
Press the P▼ or P▲ button to select the Speaker.
5
Select the On to be routed the sound to the internal speakers by
pressingMUTE
the
- or
+ button. EXIT
MUTE
EXIT
- or
MUTE
-/--
TTX/MIX
+ button.
MUTE
-/--
TTX/MIX
EXIT
EXIT
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
PRE-CH PRE-CH
-/--/-HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
English-25
Custom
Š
On
On
Mono
Š
Power
SOURCE
AUTO
DISPLAY
P.STD
STILL
S.STD
Choosing the MTS (Multichannel Television Stereo)
Power
Sound
MUTE
Mode
Bass
Treble
Dolby
Speaker
MTS
EXIT
¥
Custom
:
:
¥
On
On
Mono
Š
Depending on the particular program being broadcast, you can listen
to Stereo, Mono,
or Dual
I/II (Dual
is usuallySTILL
a foreign-language
SOURCE
SOURCE
AUTO
DISPLAY
AUTO I/IIDISPLAY
STILL
translation).
Power Power
P.STD
Š
Power
1
P.STD
S.STD
Press the MENU button.
Result:
S.STD
SOURCE
SOURCE
AUTO
2
TTX/MIX
V.DOLBY
.DOLBY
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
.SIZE
PBP
SIZE
CANCEL
DISPLAY
STILL
STILL
P.STD
P.STD
S.STD
S.STD
EXIT
EXIT
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
CANCEL
The main menu is displayed.
PRE-CH
-/--
DISPLAY
AUTO
Press the P▼ or P▲ button to select the Sound.
Result:
The options available in the Sound group are displayed.
3
Press the
4
Press the P▼ or P▲ button to select the MTS.
5
Select the required sound mode by pressing the
- or
+
button repeatedly.
The sound modesEXIT
are displayed
MUTE
MUTE
EXIT in the following
order: Mono - Stereo - Dual I - Dual II..
- or
+ button.
PIP
ON
LOCATE
LOCA
TE
MUTE
MUTE
You can also set these options simply by pressing the DUAL I/II
button. The “DUAL I/II” button displays/controls the processing and
output of the audio signal.
➣
-/--
PRE-CH
-/--
PRE-CH
◆ If the receiving conditions deteriorate, listening will be easier
if the mode is set to the Mono.
TTX/MIX
V.DOLBY
V.DOLBY switching occurs,
◆ IfTTX/MIX
the stereo
signal is weak and
an automatic
-/--/-then switch to the Mono.
HOLD receiving
DUAL
HOLDI/IIa mono
LIST/FLOF
DUAL I/IIsound
LIST/FLOF
CANCEL
CANCEL
◆ When
in the AV
mode, connect to the
“AUDIO (L)” connector on the rear panel.
TTX/MIX TTX/MIX
SLEEP
SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
ON
P.SIZE
P.SIZE
PBP
PBP
LOCATE
PIP
HOLD
ON
LOCATE
SLEEP
P.SIZE
English-26
SUBPAGE
SLEEP SUBPAGE
SIZE
P.SIZE
PBP
PBP
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
Viewing the Picture In Picture (PIP)
You can displayPower
a sub picture
Power within the main picture of TV program or
external A/V devices such as VCR or DVD. In this way you can watch
TV program or monitor the video input from any connected
devices
Power
Power
SOURCE
AUTO video
DISPLAY
AUTO
STILL
STILL
while watching
TV or SOURCE
other
input.DISPLAY
Function
Sleep Timer
¥ Off Š
PIP
Š
PBP
Š
Language
¥ English Š
SOURCE SOURCE
AUTO
1
P.STD
Press the
MENU P.STD
button.
Result:
2
S.STD
Power
P.STD
Press the
4
Press the P▼ or P▲ button to select the PIP. Press the
button.
SOURCE
AUTO
DISPLAY
AUTO
6
Function
PIP
TV/Video
Size
Position
S.STD
DISPLAY
STILL
Power P.STD
Power P.STD
On
TV
Š
Small Š
STILL
- or
+
S.STD
S.STD
MUTE
MUTE
EXIT
SOURCE
-AUTO
or
EXIT
Function
DISPLAY
STILL
+AUTO
button.DISPLAY
MUTE
STILL
MUTE
PIP
EXIT
TV/Video
Size
Position
EXIT
You can also activate the PIP simply by pressing the PIP ON
button. To deactivate
the PIP,P.STD
press it again. S.STD
P.STD
S.STD
Press the P▼ or P▲ button to select the TV/Video. Select a source
Power Power EXIT
MUTE
EXIT
of the sub picture by pressing
the MUTE
- or
+ button.
Result:
:
¥
¥
Š
The options available in the PIP group are displayed.
Select the On by pressingSOURCE
the
➣
S.STD
+ button.
SOURCE
5
S.STD
STILL
The options available in the Function group are
displayed.
P.STDPower
P.STDPower
S.STD
3
Result:
STILL
P.STD
AUTO
DISPLAY
AUTO
DISPLAY
STILL
Press the P▼ or P▲ buttonSOURCE
to selectSOURCE
the Function.
- or
DISPLAY
STILL
Power
The main menu is displayed.
Result:
DISPLAY
AUTO
S.STD
:
¥
¥
Š
On
TV
Š
Small Š
Power
The sources are displayed in the following order:
SOURCE SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
TV - Scart - Video - S-Video.
SOURCE
STILL
AUTO
DISPLAY
P.STD
STILL
S.STD
Function
7
-/--
PRE-CH
-/--
PRE-CH
Press the P▼ or P▲ button to select the Size. Select a size of the
MUTE P.STD
MUTE P.STD
EXIT S.STD
EXIT
sub picture by pressing the
- or
+ button.
-/--
-/--
PIP
TV/Video
Size
PRE-CH
Position
S.STD
PRE-CH
Result:TTX/MIX
The TTX/MIX
sizes are displayedV.DOLBY
in the following
V.DOLBY order:
Small - Medium - Large.
➣
8
TTX/MIX
TTX/MIX
V.DOLBY
You
can also
selectDUAL
these
options
simply by pressing the SIZE
HOLD
DUAL
HOLDI/II LIST/FLOF
I/II LIST/FLOF
CANCEL CANCEL
button.
PRE-CH EXIT
PRE-CH
MUTE-/-- MUTE-/-EXIT
HOLD
➣
SIZE
PIP
ON
LOCATE
PBP
EXIT
EXIT
SIZE
PIPV.DOLBY PIPV.DOLBY
P.SIZE
P.SIZE
PBP
ON
ON
PRE-CH PRE-CH
-/--/-HOLDI/IIPBP
LIST/FLOF
DUAL I/II
LIST/FLOF
CANCEL
CANCEL
LOCATE
LOCATE
P.SIZEHOLD P.SIZE
PBPDUAL
EXIT
CANCEL
PIP
PIP
TV/Video
Size
ON
Position
:
¥
¥
Š
PRE-CH
V.DOLBY
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
.SIZE
PBP
SIZE
PRE-CH
PIP
-/--/-SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
ON
P.SIZE
PRE-CH
ON
TTX/MIX TTX/MIX
LOCATE
P.SIZE
PBP
PBP
V.DOLBY
LOCATE
V.DOLBY
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
CANCEL
SLEEP
SUBPAGE
SLEEP SUBPAGE
SIZE
English-27
P.SIZE
P.SIZE
PBP
PBP
CANCEL
PIP
ON
ON
HOLD P.SIZE
DUAL
HOLDI/II P.SIZE
LIST/FLOF
DUAL I/II PBP
LIST/FLOF
CANCELLOCATE
CANCELLOCATE
PBP
SLEEP
On
TV
Š
Small Š
LOCATE
-/--
TTX/MIX
TTX/MIX SLEEP
TTX/MIXSUBPAGE
V.DOLBY SIZE
V.DOLBY PIP
SLEEP SUBPAGE
SIZE
PIP
ON
MUTE
Function
SLEEP the
SUBPAGE
SLEEP SUBPAGE
SIZE
You can also move the sub picture simply by pressing
LOCATE LOCATE
P.SIZE
P.SIZE
PBP
PBP
LOCATE button.
PRE-CH PRE-CH
-/--/-HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
MUTE
MUTE
TTX/MIX
TTX/MIX
SLEEP
SUBPAGE
SLEEP
SUBPAGE
SIZE
On
TV
Š
Small Š
V.DOLBY
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
Press the
P▼ orSUBPAGE
P▲ button
to selectSIZE
the Position.
Move the sub
SLEEP
SLEEP
SUBPAGE
SIZE
PIP
PIP
picture counterclockwise byTTX/MIX
pressingTTX/MIX
the
- or
+ button.V.DOLBY
V.DOLBY
ON
ON
:
¥
¥
Š
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
LOCATE
LOCA
TE
Viewing the Picture By Picture (PBP; Double Screen)
Power
Function
Sleep Timer
¥ Off Š
PIP
Š
PBP
Š
Language
¥ English Š
1
P.STD
Press the
MENU P.STD
button.
Result:
2
Function
PBP
TV/Video
Swap
:
¥
Š
On
TV
Power
When external A/V devices (PC, VCR, or DVD) are connected to your
set or watching TV, you can display two video sources simultaneously
Power Power
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
in the screen.SOURCE SOURCE
S.STD
Power
DISPLAY
Š
3
Press the
4
Press the P▼ or P▲ button to select the PBP. Press the
+ button.
- or
S.STD
:
¥
Š
On
TV
5
SOURCE
AUTO
:
¥
Š
On
TV
PRE-CH
TTX/MIX
V.DOLBY
P.STD
P.STD
SOURCE
AUTO
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
SIZE
7
Š
8
-/--
PBP
S.STD
S.STD
- or
DISPLAY
AUTO
EXIT
+ button.
DISPLAY
STILL
STILL
S.STD
S.STD
MUTE
MUTE
PRE-CH PRE-CH
MUTE
MUTE
EXIT
Press the
TTX/MIX
➣
- or
TTX/MIX
+ button.
EXIT
-/--
-/-V.DOLBY
EXIT
PRE-CH
PR
V.DOLBY
V.D
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
CA
V.DOLBY
The main picture and the sub picture are interchanged.
TTX/MIX
TTX/MIX
You
can also
do
by pressing
PBP button.
HOLD
DUAL
HOLD
I/II simply
LIST/FLOF
DUAL I/II
LIST/FLOF
CANCEL the
CANCEL
-/--
MUTE
P.SIZE
MUTE
SUBPAGE
SLEEP SUBPAGE
SIZE
TTX/MIX
P.SIZE
PBP
LOCATE
LOCA
TE
-/-EXIT
SIZE
PIP
TTX/MIX
ON
PRE-CH
EXIT
HOLD
PRE-CH
PIP
ON
V.DOLBY V.DOLBY
SLEEP SUBPAGE
SLEEP SUBPAGE
SIZE
LOCATE LOCATE
PBP
PRE-CH PRE-CH
-/--/-HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
P.SIZE
P.SIZE
PBP
PBP
TTX/MIX
TTX/MIX
SLEEP
SUBPAGE
SLEEP
SUBPAGE
SIZE
SIZE
PIPV.DOLBY PIPV.DOLBY
ON
-/--
TTX/MIX
-/--
SLEEP SUBPAGE
SLEEP SUBPAGE
SIZE
V.DOLBY V.DOLBY
TTX/MIX
P.SIZE
P.SIZE
PBP
PBP
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
SLEEP
SUBPAGE
SLEEP SUBPAGE
SIZE
P.SIZE
PBP
ON
HOLDI/IIPBP
LIST/FLOF
DUAL I/II
LIST/FLOF
CANCEL
CANCEL
LOCATE
LOCATE
P.SIZEHOLD P.SIZE
PBPDUAL
PRE-CH PRE-CH
HOLD
P.SIZE
English-28
STILL
- or
P.STD
EXIT
-/--
ON
P.SIZE
.SIZE
DISPLAY
STILL
Press the P▼ or P▲ button to select the Swap.
CANCEL
PIP
DISPLAY
AUTO
The sources are displayed in the following order:
TV - Scart - Video - S-Video.
SLEEP
HOLD
S.STD
Press the P▼ or P▲ button to select the TV/Video. Select a source
MUTE
EXIT
of the sub picture by pressing
the MUTE
- or
+ button.EXIT
Result:
-/--
S
You can also activate the PBP simply by pressing the PBP
button. To deactivate the PBP, press it again.
Result:
Function
MUTE
SOURCE
EXIT
PBP
TV/Video
Swap
S.STD
+ button.
Select the On by pressing the
➣
Š
6
MUTE
S
Power available in the PBP group are displayed.
Result: Power
The options
STILL
Function
PBP
TV/Video
Swap
DISPLAY
STILL
STILL
The options available in the Function group are
displayed.
P.STDPower
P.STDPower
S.STD
MUTE
P.STD
P.STD
AUTO
DISPLAY
AUTO
DISPLAY
STILL
Press the P▼ or P▲ buttonSOURCE
to selectSOURCE
the Function.
P.STD
AUTO
P.STD
DISPLAY
AUTO
Power
SOURCE
SOURCE
SOURCE
AUTO
The main menu is displayed.
Result:
Power
SOURCE
S.STD
PBP
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
SIZE
PIP
ON
LOCATE
LO
Power
SOURCE
AUTO
DISPLAY
P.STD
STILL
S.STD
Switching Off Automatically
Power
Power
You can select a time period of between 10 and 240 minutes after
SOURCE SOURCE
AUTO
DISPLAY
AUTO
STILL
STILL
your set automatically
switches
off. DISPLAY
Power
1
Result:
2
S.STD
P.STD
P.STD
S.STD
S.STD
The options available in the Function group are
displayed.
Press the
- or
+ button.
The Sleep Timer is selected.
MUTE
PRE-CH
-/--
TTX/MIX
V.DOLBY
.DOLBY
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
.SIZE
PBP
SIZE
CANCEL
PIP
ON
Select the number of minutes after which your set switches off by
pressing the
- or
+ button repeatedly.
MUTE
EXIT
Sleep Timer
¥ Off Š
PIP
Š
PBP
Š
Language
¥ English Š
STILL
Press the P▼ or P▲ button to select the Function.
Result:
4
S.STD
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
The main
menu is
displayed.
Result:
3
Power
P.STD
Press the
MENU P.STD
button.
Function
MUTE
EXIT
LOCATE
LOCA
TE
EXIT
◆ The preset time intervals: 10, 20, 30, 60, 90, 120, 150, 180, 210,
and 240 minutes.
➣
MUTE
MUTE
EXIT
EXIT
You can also select simply by pressing the “SLEEP” button.
If the sleep timer is already set, the screen displays the remaining
time and then your set will be switched off. If the sleep timer is not
yet set, displays Off.
-/--
TTX/MIX
-/--
TTX/MIX
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
PRE-CH
-/-- Information
-/-Displaying
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
TTX/MIX TTX/MIX
SLEEP SUBPAGE
SLEEP SUBPAGE
SIZE
PRE-CH
CANCEL
V.DOLBY V.DOLBY
SIZE
PIP
PIP
You can view the setting status of selected source by pressing the
ON
ON
HOLD
HOLD
I/II LIST/FLOF
DUAL
I/II LIST/FLOF
CANCEL
CANCEL information
“DISPLAY” button
on theDUAL
remote
control.
The displayed
are different depending
on the selected
source.LOCATE
LOCATE
P.SIZE
P.SIZE
PBP
PBP
SLEEP
P.SIZE
SUBPAGE
SLEEP SUBPAGE
SIZE
P.SIZE
PBP
PBP
SIZE
PIP
PIP
ON
ON
LOCATE
LOCATE
Power
SOURCE
AUT
UTO
DISPLA
DISPLAY
STILL
P.STD
.STD
S.STD
.STD
MUTE
EXIT
PRE-CH
-/--
TTX/MIX
English-29
HOLD
DUAL I/II LIST/FLOF
SLEEP
SUBPAGE
P.SIZE
PBP
SIZE
V.DOLBY
CANCEL
PIP
ON
LOCATE
Power
Power
Adjusting the Brightness and Contrast
➣
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL button.
STILL
Preset to the
PC mode
by pressing
the SOURCE
Power
Power
P.STD
SOURCE
PC
1
Image
Š
Image Lock
Š
Position
Š
Color Adjust Š
Recall
Š
1024x768
48kHz
Result:
2
59Hz
PC
4
5
75
SOURCE
AUTO
DISPLAY
P.STD
S.STD
STILL
Power
P.STD
S.STD
S.STD
Press the P▼ or P▲ button to select the PC.
6
Power
Press the
- or
+ button.
Press the
- or
+ button again.
P.STD
P.STD
S.STD
AUTO is DISPLAY
AUTO
DISPLAY
STILL
Result:SOURCE
The SOURCE
Image
selected.
S.STD
STILL
P.STD
P.STD
S.STD
S.STD
MUTE available in the
EXITImageEXIT
Result: MUTEThe options
group are displayed.
Select the option (Brightness or Contrast) to be adjusted for the
color of your computer image by pressing the P▼ or P▲ button.
MUTE
MUTE
EXIT
Press the
- or
+ button. EXIT
Result:
Power
S.STD
DISPLAY
STILL
The main menu is displayed.
Power
P.STD
Power
Brightness
DISPLAY
AUTO
AUTO available
DISPLAY
AUTO inDISPLAY
STILLPC group
STILLare displayed.
Result:SOURCE
The SOURCE
options
the
3
Image
Brightness
Contrast
¥ Expanded 1Š
Size
P.STD
SOURCE
AUTO
Press the MENU button.
The horizontal bar is displayed.
Press the
- or
MUTE
MUTE
-/--
-/--
MUTE
MUTE
TTX/MIX
-/--
TTX/MIX
-/--
+ button to reach the required setting.
EXIT
EXIT
PRE-CH
PRE-CH
EXIT
EXIT
STILL
S.STD
Power
V.DOLBY V.DOLBY
PRE-CH PRE-CH
Power
Selecting the Image Size
➣
MUTE
EXIT
PC
Image
Brightness
Contrast
¥ Expanded 1Š
Size
1
Power
Result:
2
HOLD
V.DOLBY
DUAL
DU
AL I/II LIST/FLOF
3
SLEEP
SLEEP
SUBPAGE
SUBP
GE
SIZE
PIP
SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
4
PIP
P.STD
P.STD
HOLD - DUAL
HOLDI/II +LIST/FLOF
DUAL
I/II LIST/FLOF
CANCEL
CANCEL
Press the
or
button.
ON
ON
Result: P.SIZEThe Image
LOCATE
P.SIZE
PBP is selected.
PBP
CANCEL
DISPLAY
AUTO
DISPLAY
STILL
STILL
The options available in the PC group are displayed.
SLEEP
TTX/MIX
Power
The main menu is displayed.
ON
ON
P.STD
P.STD
S.STD
S.STD
HOLD
HOLD
LIST/FLOF
DUAL
LIST/FLOF
CANCEL
LOCATE
LOCATE
P.SIZE
P.SIZE
PBPI/II
PBP
Press the
P▼ orDUAL
P▲
button
toI/IIselect
the PC.CANCEL
TTX/MIX TTX/MIX
V.DOLBY
SOURCE V.DOLBY
SOURCE
AUTO
Result:
PRE-CH
-/--
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
TTX/MIX TTX/MIX
V.DOLBY V.DOLBY
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL button.
STILL
Preset to the
PC mode
by pressing
the SOURCE
Power
Power
SLEEP
SUBPAGE
SLEEP
SUBPAGE
SIZE
SIZE
PIP
PIP
PRE-CH PRE-CH
-/--/-HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
ON
ON
P.STD
P.STD
S.STD
S.STD
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
LOCATE LOCATE
P.SIZE
P.SIZE
PBP
PBP
Press the
MENUTTX/MIX
button.
TTX/MIX
V.DOLBY
V.DOLBY
SLEEP
SUBPAGE
SLEEP
SUBPAGE
SIZE
SIZE
PIP
PIP
PRE-CH
PRE-CH
-/--/--
Press the
SUBPAGE
SLEEP SUBPAGE
SIZE
- or
SIZE
PIP
+ button again.
ON
S.STD
S.STD
LOCATE
PIP
ON
ON
P.SIZE
.SIZE
PBP
MUTEThe options
MUTE
EXITImage
EXIT
Result: P.SIZE
inLOCATE
the
group are displayed.
LOCATE
P.SIZE
PBP available
PBP
LOCATE
LOCA
TE
5
Press the P▼ or P▲ button to select the Size. Select a size of the
your computer image by pressing the
- or
+ button.
MUTE
Result:
➣
MUTE
EXIT
EXIT
The sizes are displayed in the following order:
Expanded 1 - Expanded 2 - Normal.
You can also select these options simply by pressing the
P.SIZE (Picture Size) button. MUTE
MUTE
EXIT
-/--
-/--
PRE-CH
EXIT
PRE-CH
English-30
TTX/MIX
-/--
TTX/MIX
-/--
V.DOLBY V.DOLBY
PRE-CH PRE-CH
HOLD
TTX/MIX
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
TTX/MIX
V.DOLBY V.DOLBY
SLEEP
SUBPAGE
SLEEP SUBPAGE
SIZE
-/-SIZE
PIP
-/-PIP
PRE-CH
PRE-CH
Adjusting the Image Quality
➣
Power
Power
Preset to the PC mode by pressing the SOURCE button.
Power
SOURCE SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
Power
This feature is used to fine tune and get the best image by removing
PC
noises that create unstable images with jitters and shimmers. SOURCE
SOURCE P.STD
AUTO
1
STILL
S.STD
Power
AUTO
DISPLAY
S.STD
Press the MENU button.
Result:
P.STD
2
P.STD
DISPLAY
P.STD
The main menu is
displayed.
S.STD
Power
Image
Š
STILL
Image Lock
Š
Position
Š
Color
S.STD Adjust Š
Recall
Š
1024x768
48kHz
59Hz
Press the P▼ or P▲ button to select the PC.
Result:
options available
inSTILL
the PC group are displayed.
SOURCE
SOURCE
AUTO TheDISPLAY
AUTO
DISPLAY
STILL
Power
3
Press the
P.STD
4
Power
- or
P.STD
PC
+ button.
S.STD
Image Lock
Coarse
Fine
S.STD
SOURCE
AUTObutton
DISPLAY
AUTO
DISPLAY
STILL
STILL
Press the
P▼ orSOURCE
P▲
to select
the Image
Lock. Press the
or
+ button.
-
Result: P.STDThe options
the ImageS.STD
Lock group are
P.STD available in S.STD
MUTE
MUTE
EXIT
EXIT
displayed.
5
MUTE
Select the option (Coarse or Fine) to be adjusted for the quality
of
MUTE
EXIT
your
computer image by pressing
the P▼ or P▲ button. Press the
- or
+ button.
Result:
6
MUTE
1344
- or
MUTE
+ button to reach the required setting.
EXIT
EXIT
This feature may change the width of the image. If necessary, adjust
PRE-CH PRE-CH
-/-- to center.
-/-the position
-/--
MUTE
TTX/MIX
Power
MUTE
TTX/MIX
EXIT
PRE-CH V.DOLBY
EXIT
V.DOLBY
Power
1
2
3
4
Power
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL button.
STILL
HOLD
DUAL I/II LIST/FLOF CANCEL
Power
Preset
to the
PC mode
by pressing
the SOURCE
SLEEP
SIZE
PIP
PIP
HOLD SLEEP
DUAL I/II SUBPAGE
LIST/FLOFSUBPAGE
CANCEL SIZE
PRE-CH PRE-CH
-/--/-PC
SOURCE
AUTO
DISPLAY
STILL
ON
ON
S.STDPower
SLEEP SUBPAGE
SIZE
PIP
Image
Š
SOURCE P.STD
AUTO P.STD
DISPLAY
STILL S.STDPower
P.SIZE
PBP
PBPPIP LOCATE LOCATE
Image
Š
SLEEP the
SUBPAGE
SIZE
ON Lock
Press
MENUP.SIZE
button.
P.STD
S.STD
TTX/MIX TTX/MIX
V.DOLBY
V.DOLBY
Position
Š
ON
PRE-CH PRE-CH
-/--/-Color
Result:
The main menu is
displayed.
P.STD
S.STD
LOCATEAdjust Š
SOURCE SOURCE
AUTO
DISPLAY
AUTOP.SIZEDISPLAY
STILLPBP STILL
Recall
Š
Power
LOCATE
P.SIZE Power
PBP
1024x768
48kHz
HOLD
HOLDP▼
I/II LIST/FLOF
DUAL
LIST/FLOF
CANCEL
CANCEL
Press DUAL
the
or
P▲I/IIbutton
to select
the PC.
TTX/MIX TTX/MIX
V.DOLBY V.DOLBY
P.STD
P.STD
S.STD
S.STD
Result:SOURCE
The SOURCE
options
available
in
the
AUTO
DISPLAY
AUTO
DISPLAY
STILLPC group
STILLare displayed.
SLEEP SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
PIP
HOLD - DUAL
HOLDI/II +LIST/FLOF
DUAL
I/II LIST/FLOF
CANCEL CANCEL
Press the
or
button.
ON
ON
PC
P.STD
P.STD
S.STD
S.STD
Position
Press the
P▲ button
to select
the Position. Press the
LOCATE
LOCATE
P.SIZE
P.SIZE
PBPP▼ or PBP
H-Position
SLEEP SUBPAGE
SIZE
SIZE
PIP
PIP
or
+SLEEP
button.SUBPAGE
59Hz
V-Position
ON
Select the
position
(H-Position or V-Position)
MUTE
MUTE
EXIT
EXIT to be adjusted by
LOCATE LOCATE
PBP
PBP
pressingP.SIZE
the P▼ P.SIZE
or
P▲ button.
Press
the
- or
+ button.
Result:
MUTE
The horizontal bar is displayed.
MUTE
6
V.DOLBY
DUAL
HOLDI/II LIST/FLOF
DUAL
I/II LIST/FLOF
CANCEL
V.DOLBY
ON
5
PRE-CH
-/--
TTX/MIX
CANCEL
Changing the Image Position
HOLD
TTX/MIX
➣
Coarse
The horizontal bar is displayed.
Press the
➣
EXIT
EXIT
EXIT
Press the
- or
+ button to reach the required setting.
MUTE
MUTE
EXIT
EXIT
H-Position
50
MUTE
MUTE
-/--
-/--
EXIT
EXIT
PRE-CH
PRE-CH
English-31
PRE-CH
-/--/--
TTX/MIX
TTX/MIX
PRE-CH V.DOLBY
V.DOLBY
TTX/MIX
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL-/--CANCEL-/--
V.DOLBY
PRE-CH
PRE-CH
Power
Power
Adjusting the Color
➣
SOURCE
PC
Image
Š
Image Lock
Š
Position
Š
Color Adjust Š
Recall
Š
1024x768
48kHz
SOURCE SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
Power
Power
Preset to the
PC mode by pressing the SOURCE button.
1
P.STD
SOURCE
AUTO
P.STD
DISPLAY
AUTO
DISPLAY
STILL
S.STD
STILL
Press the MENU button.
S.STD
Power
Power
Result:P.STD The main menu
is displayed.
P.STD
S.STD
S.STD
2
59Hz
AUTO
Press the P▼ or P▲ button to select the PC.SOURCE SOURCE
Result:
DISPLAY
STILL
STILL
S.STD
S.STD
EXIT
EXIT
PRE-CH
PRE-CH
V.DOLBY
V.DOLBY
DUAL
HOLD
I/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL
Power
CANCEL
The options available in the PC group are displayed.
P.STD
PC
Color Mode
Red
Green
Blue
¥
Press the
Power - or
Power + button.
4
Press the P▼ or P▲ button to select the Color Adjust. Press the
- or
SOURCE+ button.
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
Result:
5
Color Mode
Red
Green
Blue
¥
P.STD
3
Custom Š
6
PC
DISPLAY
AUTO
Custom Š
Power
Power
The options available in the Color Adjust group are
MUTE
MUTE
displayed
with the ColorEXIT
Mode isEXIT
selected.
P.STD
P.STD
S.STD
S.STD
SOURCE SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
Select the required color mode by pressing the
- or
+ button
MUTE
EXIT
EXIT
repeatedly.
The following color
modes
are available: Custom Color 1P.STD
- ColorP.STD
2 - Color 3. S.STD
S.STD
MUTE
If you wish adjust the color which best corresponds to your viewing
requirements, select the option (Red, Green, or
Blue) to
be adjusted
MUTE
MUTE
by pressing the P▼ or P▲ button.
Press the
- or
+ button.
Result: -/--The horizontal
bar is displayed.
PRE-CH PRE-CH
-/--
7
Press the
-/--
➣
Red
-/-TTX/MIX
MUTE
- or
PRE-CH
V.DOLBY
EXIT
V.DOLBY
EXIT
DUAL
HOLDI/II V.DOLBY
LIST/FLOF
DUAL I/II V.DOLBY
LIST/FLOF
CANCEL
MUTE
EXIT
CANCEL
EXIT
-/--
If you change the Red, Green, or Blue settings, the Color mode is
selected to Custom automatically.
TTX/MIX
100
HOLD
SLEEP
HOLD
TTX/MIX
MUTE
SLEEP
SUBPAGE
SLEEP
SUBPAGE
SIZE CANCEL
SIZE
PIP
DUAL
HOLD
I/II LIST/FLOF
DUAL
I/II LIST/FLOF
CANCEL
ON
P.SIZE
P.SIZE
PBP
SUBPAGE
SLEEP
SIZE
Power SUBPAGE
Power
Initializing the Image Settings
➣
59Hz
2
3
ON
LOCATE
PIP
ON
TTX/MIX
LOCATE
ON
HOLD
PRE-CH
PRE-CH
-/--/-Power P.SIZE
LOCATE
LOCATE
P.SIZE
PBP
PBP
SOURCE
SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL button.
STILL
Preset to the
PC mode
by pressing
the SOURCE
TTX/MIX
Press the
P▼ orSUBPAGE
P▲ button
to selectSIZE
the PC. PIP
SLEEP
SLEEP
SUBPAGE
SIZE
PIP
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL P.STD
CANCEL P.STD
The options available in the
Result:
ON PC group
ON are displayed.
Press the
LOCATE
P.SIZE - or
P.SIZE
PBP + button.
PBP
SLEEP
PC
PBP
SIZE
PIP
-/--
PIP
SLEEP SUBPAGE
SLEEP
SIZE
PIP
SOURCESUBPAGE
AUTO SIZE
DISPLAY PIP
STILL
SOURCE
AUTO
DISPLAY
STILL
ON
ON
P.STD
P.STD
S.STD
S.STD
TTX/MIX
TTX/MIX
V.DOLBY
V.DOLBY
You can replace-/-all image
settings
with
the
factory
default
values.
PRE-CH PRE-CH
-/-Power Power
LOCATE LOCATE
P.SIZE
P.SIZE
PBP
P.STD PBP
S.STD
1 P.STD
Press the
MENU
button.
S.STD
HOLD
DUAL
HOLDI/II LIST/FLOF
DUAL I/II LIST/FLOF
CANCEL CANCEL
V.DOLBY SOURCE
V.DOLBY SOURCE
AUTO
DISPLAY
AUTO
DISPLAY
STILL
STILL
The TTX/MIX
main menu is displayed.
Result:TTX/MIX
PC
Image
Š
Image Lock
Š
Position
Š
Color Adjust Š
Recall
Š
1024x768
48kHz
+ button to reach the required setting.
PRE-CH
TTX/MIX
MUTE
SUBPAGE
SLEEP SUBPAGE
SIZE
SIZE
PIP
Press the P▼ or P▲ button to select the
- or
ON Recall.
ON Press the
+ button.
LOCATE
P.SIZE
PBP available
PBP
inLOCATE
the Recall
group are displayed.
Result: P.SIZEThe options
5
Select the option (Image Recall or Color Recall) to be replaced
by pressing the P▼ or P▲ button. Press the
- or MUTE
+ button.
MUTE
EXIT
The screen becomes
black and return to original view
Result:
about a few seconds later.
MUTE
MUTE
EXIT
S.STD
LOCATE
PIP
4
Recall
Image Recall Š
Color Recall Š
S.STD
EXIT
EXIT
English-32
MUTE
-/--
-/--
PRE-CH
MUTE
EXIT
EXIT
PRE-CH
-/--
PRE-CH
Display Modes
If the signal from the system equals to the standard signal mode, the screen is adjusted automatically.
If the signal from the system doesn’t equal to the standard signal mode, adjust the mode with referring
to the Video card user guide because the screen might not display or only the power LED might be on.
For the display modes listed below, the screen image has been optimized during manufacture.
Mode
Resolution
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Pixel Clock
Frequency (MHz)
Sync Polarity
(H/V)
VGA
720 x 400
640 x 480
640 x 480
640 x 480
31.469
31.469
37.500
43.269
70.087
59.940
75.000
85.008
28.322
25.175
31.500
36.000
-/+
-/-/-/-
SVGA
800 x 600
800 x 600
46.875
53.674
75.000
85.061
49.500
56.250
+/+
+/+
XGA
1024 x 768
1024 x 768
1024 x 768
48.363
60.023
68.677
60.004
75.029
84.997
65.000
78.750
94.500
-/+/+
+/+
SXGA
1280 x 1024
1280 x 1024
63.981
79.976
60.020
75.025
108.000
135.000
+ / -, + / +/+
UXGA
1600 x 1200
75.000
60.000
162.000
+ / -, + / -
WUXGA
1920 x 1200
(LW24R15W)
75.000
60.000
193.156
+ / -, + / -
PowerSaver
This set has a built-in power management system called PowerSaver. This system saves energy by
switching your set into a low-power mode when it has not been used for a certain period of time.
The available modes are “On”, “Standby”, “Sleep”, and “Deep Sleep”. PowerSaver operates with a
VESA DPMS compliant video card installed in your computer. You use a software utility installed on
your computer to set up this feature.
State
Normal Operation
Power-Saving Function mode (EPA/NUTEK)
Horizontal Sync
Active
Inactive
Vertical Sync
Active
Inactive
Power Indicator
Green
Green, Blinking (1 sec interval)
LW24R15W : 120W (Max.)
Less than 8W
Power Consumption
➣
This set automatically returns to normal operation when horizontal and vertical sync return.
This occurs when you move the computer’s mouse or press a key on the keyboard.
English-33
Teletext Feature
Most television channels provide written information services via
teletext. Information provided includes:
◆ Television programme times
◆ News bulletins and weather forecasts
◆ Sports results
◆ Travel information
This information is divided into numbered pages (see diagram).
Part
Contents
A
Selected page number.
B
Broadcasting channel identity.
C
Current page number or search indications.
D
Date and time.
E
Text.
F
Status information.
FASTEXT information.
➣
Teletext information is often divided between several pages
displayed in sequence, which can be accessed by:
◆ Entering the page number
◆ Selecting a title in a list
◆ Selecting a coloured heading (FASTEXT system)
Power
SOURCE
Displaying the Teletext Information
AUTO
DISPLAY
P.STD
STILL
S.STD
You can display Teletext information at any time on your set.
☛
P
MENU
P
MUTE
For Teletext information to be displayed correctly, channel
reception must be stable; otherwise:
◆ Information may be missing
◆ Some pages may not be displayed
EXIT
1
2
3
4
5
6
7
8
9
1
Select the channel providing the Teletext service using the P▼ or P▲
button.
2
Press the TTX/MIX button to activate the teletext mode.
Result:
The contents page is displayed. It can be redisplayed at
any time by pressing the
(index) button.
PRE-CH
-/-0
TTX/MIX
3
If you wish to display the actual broadcast at the same time as the
teletext page, press the TTX/MIX button again.
4
To return to normal viewing, press the CANCEL (
5
Press the TTX/MIX button again to exit from the teletext display.
V.DOLBY
.DOLBY
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
PBP
SIZE
CANCEL
PIP
ON
English-34
LOCATE
) button.
Selecting a Page by Number
Power
SOURCE
You can enter the page number directly by pressing the numeric
buttons on the remote control.
1
Enter the three-digit page number given in the content by pressing
the corresponding numeric buttons.
AUTO
DISPLAY
P.STD
.STD
STILL
S.STD
.STD
P
Power
MENU
Result:
2
The current page counter is incremented and the page is
then displayed.
If the selected page is linked with several secondary pages, the
secondary pages are displayed in sequence. To freeze the display on
a given page, press the HOLD ( ) button. Press the HOLD ( )
button again to resume.
Using the various display options:
SOURCE
AUTO
DISPLAY
P
P.STD
MUTE
S.STD
EXIT
1
2
3
4
5
6
7
8
9
PRE-CH
-/-0
MUTE
To display...
Press the...
◆ Both teletext information and
the normal broadcast
TTX/MIX
EXIT
TTX/MIX
V.DOLBY
.DOLBY
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
.SIZE
PBP
SIZE
(reveal)
◆ The normal screen
(reveal) again
PIP
LOCATE
LOCA
TE
PRE-CH
-/--
TTX/MIX
SUBPAGE (
CANCEL
ON
◆ Hidden text
(answers to quiz games, for example)
◆ A secondary page,
by entering its 4-digit number
STILL
V.DOLBY
)
HOLD
DUAL
DU
AL I/II LIST/FLOF
◆ The next page
(page up)
SLEEP
SUBPAGE
SUBP
GE
◆ The previous page
(page down)
P.SIZE
.SIZE
PBP
SIZE
CANCEL
PIP
ON
◆ Double-size letters in the:
• Upper half of the screen
• Lower half of the screen
SIZE ( )
• Once
• Twice
◆ Normal screen
• Three times
English-35
LOCATE
LOCA
TE
MUTE
EXIT
Using FLOF to Select a Page
PRE-CH
-/--
TTX/MIX
V.DOLBY
.DOLBY
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
SIZE
CANCEL
PIP
The various topics included in the teletext pages are color-coded, and
can be selected by pressing the colored buttons on the remote control.
1
Display the teletext contents page by pressing the TTX/MIX button.
2
Press the coloured button corresponding to the topic that you wish to
select;the available topics are given on the status line.
ON
P.SIZE
.SIZE
LOCATE
LOCA
TE
PBP
Power
SOURCE
AUTO
DISPLAY
P.STD
Result:
STILL
The page is displayed with other coloured information that
can be selected in the same way.
S.STD
P
3
To display the previous or next page, press the corresponding
coloured button.
4
To display the subpage, see the following steps.
◆ Press the SUBPAGE ( ) button.
Result:
The available subpages appear.
MENU
P
MUTE
◆ Select the required sub-page. Sub-pages can be scrolled by using
the
(P▼) or
(P▲) button.
EXIT
Power
SOURCE
AUTO
DISPLAY
STILL
P.STD
S.STD
-/--
PRE-CH
TTX/MIX
V.DOLBY
Storing Teletext Pages
HOLD
DUAL I/II LIST/FLOF
SLEEP
SUBPAGE
MUTE
P.SIZE
PBP
SIZE
CANCEL
PIP
ON
EXIT
LOCATE
1
2
3
4
5
6
7
8
9
You can store up to four teletext pages to display them later at leisure.
1
Result:
➣
PRE-CH
-/-0
TTX/MIX
V.DOLBY
.DOLBY
HOLD
DUAL
DU
AL I/II LIST/FLOF
SLEEP
SUBPAGE
SUBP
GE
P.SIZE
.SIZE
PBP
SIZE
CANCEL
) button.
Four 3-digit numbers are displayed in different colors.
The LIST/FLOF ( ) button is used to switch between the
LIST and FLOF modes.
2
Press the colored button corresponding to the page that will be
replaced.
3
Enter the new page number using the numeric buttons.
4
Repeat steps 2 and 3 for each page to be stored, using a different
colored button each time.
5
Press the
PIP
ON
English-36
Select the LIST mode using the LIST/FLOF (
LOCATE
LOCA
TE
(store) button until the corresponding blocks blink.
Troubleshooting: Before Contacting Service Personnel
Before contacting Samsung after-sales service, perform the following simple checks.
If you cannot solve the problem using the instructions below, note the model and serial number of your
set and contact your local dealer.
No sound or picture
◆
◆
◆
◆
Normal picture but no sound
◆ Check the volume.
◆ Check whether the MUTE button has been pressed on the remote
control.
No picture or black and white picture
◆ Adjust the color settings.
◆ Check that the broadcast system selected is correct.
Sound and picture interference
◆ Try to identify the electrical appliance that is affecting the set and
move it further away.
◆ Plug your set into a different mains socket.
Blurred or snowy picture,
distorted sound
◆ Check the direction, location and connections of your aerial.
This interference is often due to the use of an indoor aerial.
Remote control malfunctions
◆ Replace the remote control batteries.
◆ Clean the upper edge of the remote control (transmission window).
◆ Check the battery terminals.
“Check Signal Cable” message is
displayed.
◆ Check that the signal cable is firmly connected to the PC or video
sources.
◆ Check that the PC or video sources are turned on.
On PC mode, “Not Supported Mode”
message is displayed.
◆ Check the maximum resolution and the frequency of the video
Adapter.
◆ Compare these values with the data in the Display Modes Timing
Chart.
On PC mode, horizontal or vertical bars
appear to flicker, jitter or shimmer on the
image.
◆ Adjust the Coarse or Fine function.
On PC mode, screen is black and
power indicator light is steady amber
or blinks every 0.5 or 1 seconds
◆ The TV is using its power management system.
◆ Move the computer’s mouse or press a key on the keyboard.
On PC mode, image is not stable and
may appear to vibrate.
◆ Check that the display resolution and frequency from your
computer or video board is an available mode for your set. On your
computer check: Control Panel, Display, Settings.
◆ If the setting is not correct, use your computer utility programme to
change the display settings.
Check that the mains lead has been connected to a wall socket.
Check that you have pressed the Power ( ) button.
Check the picture contrast and brightness settings.
Check the volume.
➣
Your set supports multiscan display functions within the
following frequency domain:
Horizontal frequency: 30 ~ 85 kHz
Vertical frequency: 55 ~ 85 Hz
On PC mode, image is not centered
on the screen.
◆ Adjust the horizontal and vertical position.
You need the Monitor driver software.
◆ Download the driver from WWW pages:
http://www.samsungusa.com/monitor
http://www.samsung-monitor.com
English-37
Technical and Environmental Specifications
Model
LW24R15W
Panel
Size
Display Size
Type
Pixel Pitch
Viewing Angle
24.06” Diagonal
518.4(H) x 324(V) mm
a-si TFT active matrix
0.27 (H) x 0.27 (V) mm
80/80/80/80 (L/R/T/B)
Frequency
Horizontal
Vertical
Display Color
30 ~ 85 kHz
55 ~ 85 Hz
16,777,216 colors
Display Resolution
Maximum Mode
Input Signal
Sync.
Video Signal
TV/Video
Color System
Sound System
Video Format
Scart
Video Input/Output
RGB Input
Audio Input/Output
1920 x 1200 @ 60 Hz
H/V Separate, TTL, P. or N.
H/V Composite, TTL, P. or N.
Sync-on-green 0.3 Vp-p, N.
0.7 Vp-p @ 75 ohm
PAL, SECAM, NTSC4.43
B/G, D/K, I, L, L’
CVBS, S-VHS
1.0 Vp-p @ 75 ohm
0.7 Vp-p @ 75 ohm
500mVrms
Color system
PAL
Power Supply
Input
Output
100 - 240 V (50Hz / 60Hz)
DC 14V/8A
Power Consumption
Maximum
Power Saving
Dimensions (W X D X H)
Environmental Considerations
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
Audio Characteristics
Audio Input
Audio Input (PC)
Audio Output
Speaker Output
Headphone Output
Frequency
Response
English-38
120 W
<8W
618 x 67.5 x 422 (TV body)
665.2 x 218.2 x 472 (With stand)
50 °F to 104 °F (10 °C to 40 °C)
10% to 80%
- 13 °F to 113 °F (-25 °C to 45 °C)
5% to 95%
RCA Jack (L, R), 0.5Vrms (-9dB)
3.5Ø Stereo Jack, 0.5Vrms (-9dB)
RCA Jack (L, R), 0.5Vrms (-9dB)
Max. 5W Output (3.5Ø Stereo Jack, 2)
Max. 10mW Output (3.5Ø Stereo Jack, 32Ω)
RF: 80Hz ~ 15kHz (at- 3dB)
A/V: 80Hz ~ 20kHz (at- 3dB)
Wiring the Mains Power Supply Plug (UK Only)
◆ IMPORTANT NOTICE
The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse
is indicated on the pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same
rating must be used. Never use the plug with the fuse cover omitted if the cover is detachable.
If a replacement fuse cover is required, it must be of the same color as the pin face of the plug. Replacement
covers are available from your dealer. If the fitted plug is not suitable for the power points in your house or the
cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead
or consult your dealer for assistance. However, if there is no alternative to cutting off the plug, remove the fuse
and then safely dispose of the plug. Do NOT connect the plug to a mains socket as there is a risk of shock
hazard from the bared flexible cord.
◆ IMPORTANT
The wires in the mains lead are colored in accordance with the following code:
BLUE - NEUTRAL
BROWN - LIVE
As these colors may not correspond to the colored markings identifying the terminals in your plug,
proceed as follows:
The wire colored BLUE must be connected to the terminal marked with the letter N or colored BLUE or
BLACK. The wire colored BROWN must be connected to the terminal marked with the letter L or colored
BROWN or RED.
WARNING:
DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED
WITH THE LETTER E OR BY THE EARTH SYMBOL , OR COLORED GREEN OR GREEN
AND YELLOW.
English-39
- AFTER SALES SERVICE
- Do not hesitate to contact your retailer or service agent
if a change in the performance of your product
indicates that a faulty condition may be present.
ELECTRONICS
BN68-00169E-02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement