Multi Variable Air Conditioners Ducted Type Indoor Unit

Multi Variable Air Conditioners Ducted Type Indoor Unit
Multi Variable Air Conditioners
Ducted Type Indoor Unit
Owner's Manual
Air Conditioners
Models:
GMV-ND72PH/A-T(U)
GMV-ND96PH/A-T(U)
 Thank you for choosing Air Conditioners, please read this owner’s manual carefully before
operation and retain it for future reference.
Preface
For correct installation and operation, please read all instructions carefully. Before reading the
instructions, please be aware of the following items:
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING
This mark indicates procedures which, if improperly performed, might lead to the death or
serious injury of the user.
CAUTION
This mark indicates procedures which, if improperly performed, might possibly result in
personal harm to the user, or damage to property.
NOTICE is used to address practices not related to personal injury.
WARNING
(1) Instructions for installation and use of this product are provided by the manufacturer.
(2) Installation must be performed in accordance with the requirements of NEC and CEC by authorized personnel
only.
(3) For the safe operation of this unit, please read and follow the instructions carefully.
(4) During operation, total capacity of indoor units should not exceed the total capacity of outdoor units. Otherwise,
poor effect of cooling or heating may result.
(5) Direct operators or maintainers should well keep this manual.
(6) If this unit fails to operate normally, please contact our service center as soon as possible and provide the
following information:
1) Content on the nameplate (model number, cooling capacity, production code, ex-factory date.
2) Malfunction details (before and after the malfunction occurs.
(7) Each unit has been strictly tested and proved to be qualified before ex-factory. In order to prevent units from
being damaged or operating normally because of improper disassembly, please do not disassemble the unit by
yourself. If you need to disassemble and check units, please contact our service center. We will send specialists
to guide the disassembly.
(8) Installation must be performed in accordance with the requirements of NEC and CEC by authorized personnel
only.
(9) Under the standby status, the unit will consume a little power for ensuring reliability of complete unit, maintaining
normal communication and preheating refrigerant. When the unit won’t be used for a long time, cut off the power
of the complete unit. However, please preheat it when operating the unit next time.
User Notice

This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.

DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection of such
waste separately for special treatment is necessary.
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and collection
systems or contact the retailer where the product was purchased. They can take this
product for environmental safe recycling.
410A (R32/125:50/50):2087.5
Contents
1 Safety Precautions .................................................................................................. 1
2 Product Introduction ................................................................................................ 2
2.1 Names of Key Components ......................................................................................... 2
2.2 Rated Working Condition ............................................................................................. 2
3 Preparations for Installation ..................................................................................... 3
3.1 Standard Fittings .......................................................................................................... 3
3.2 Location for Installation ................................................................................................ 4
3.3 Requirements for Communication Line ........................................................................ 4
3.4 Wiring Requirements.................................................................................................... 6
4 Installation Instructions ............................................................................................ 6
4.1 Installation of Indoor Unit.............................................................................................. 6
4.2 Refrigerant Pipe Connection ........................................................................................ 8
4.3 Drainage Pipe Installation and Drainage System Testing ............................................. 9
4.4 Installation of Air Duct ................................................................................................. 11
4.5 Installation of Wired Controller ....................................................................................12
4.6 External Static Pressure Settings ................................................................................12
5 Wiring Work ........................................................................................................... 13
5.1 Connection of Wire and Patch Board Terminal ............................................................14
5.2 Power Cord Connection ..............................................................................................14
5.3 Connection of Communication Wire between Indoor Unit and Outdoor Unit (or indoor
unit)...................................................................................................................................15
5.4 Connect Communication Wire of Wired Controller ......................................................15
5.5 Illuminate for Connection of Wired Controller and Indoor Units Network .....................16
6 Routine Maintenance ............................................................................................. 18
6.1 Cleaning of Filter .........................................................................................................18
6.2 Maintenance before the Seasonal Use........................................................................18
6.3 Maintenance after the Seasonal Use ..........................................................................18
7 Table of Error Codes for Indoor Unit ...................................................................... 19
8 Troubleshooting ..................................................................................................... 19
Multi Variable Air Conditioners Ducted Type Indoor Unit
1 Safety Precautions
WARNING
(1) Follow this instruction to complete the installation work. Please carefully read this manual before unit startup
and service.
(2) Wire size of power cord should be large enough. The damaged power cord and connection wire should be
replaced by exclusive cable.
(3) After connecting the power cord, please fix the electric box cover properly in order to avoid accident.
(4) Never fail to comply with the nitrogen charge requirements. Charge nitrogen when welding pipes.
(5) Never short-circuit or cancel the pressure switch to prevent unit damage.
(6) Please firstly connect the wired controller before energization, otherwise wired controller cannot be used.
(7) Before using the unit, please check if the piping and wiring are correct to avoid water leakage, refrigerant
leakage, electric shock, or fire etc.
(8) Do not insert fingers or objects into air outlet/inlet grille.
(9) Open the door and window and keep good ventilation in the room to avoid oxygen deficit when the gas/oil
supplied heating equipment is used.
(10) Never start up or shut off the air conditioner by means of directly plug or unplug the power cord.
(11) Turn off the unit after it runs at least five minutes; otherwise it will influence oil return of the compressor.
(12) Do not allow children operate this unit.
(13) Do not operate this unit with wet hands.
(14) Turn off the unit or cut off the power supply before cleaning the unit, otherwise electric shock or injury
(15) may happen.
(16) Never spray or flush water towards unit, otherwise malfunction or electric shock may happen.
(17) Do not expose the unit to the moist or corrosive circumstances.
(18) Under cooling mode, please don't set the room temperature too low and keep the temperature difference
between indoor and outdoor unit within 5℃ (41℉).
(19) User is not allowed to repair the unit. Fault service may cause electric shock or fire accidents. Please
contact AC PRO appointed service center for help.
(20) Before installation, please check if the power supply is in accordance with the requirements specified on
the nameplate. And also take care of the power safety.
(21) Installation should be conducted by dealer or qualified personnel. Please do not attempt to install the unit
by yourself. Improper handling may result in water leakage, electric shock or fire disaster etc.
(22) Be sure to use the exclusive accessory and part to prevent the water leakage, electric shock and fire
accidents.
(23) Make sure the unit can be earthed properly and soundly after plugging into the socket so as to avoid
electric shock. Please do not connect the ground wire to gas pipe, water pipe, lightning rod or telephone
line.
(24) Electrify the unit 8 hours before operation. Please switch on for 8 hours before operation. Do not cut off the
power when 24 hours short-time halting (to protect the compressor).
(25) If refrigerant leakage happens during installation, please ventilate immediately. Poisonous gas will emerge
if the refrigerant gas meets fire.
1
Multi Variable Air Conditioners Ducted Type Indoor Unit
(26) Volatile liquid, such as diluent or gas will damage the unit appearance. Only use soft cloth with a little
neutral detergent to clean the outer casing of unit.
(27) If anything abnormal happens (such as burning smell), please power off the unit and cut off the main power
supply, and then immediately contact AC PRO appointed service center. If abnormality keeps going, the unit
might be damaged and lead to electric shock or fire.
2 Product Introduction
2.1 Names of Key Components
No.
①
②
③
④
⑤
Name
Filter
Air Inlet
Air Outlet
Fittings
Drain Pipe
2.2 Rated Working Condition
Indoor Side Condition
Outdoor Side Condition
Dry Bulb
Temp °C(℉)
Wet Bulb
Temp °C(℉)
Dry Bulb
Temp °C(℉)
Wet Bulb
Temp °C(℉)
Rated Cooling
26.7(80.0)
19.4(67.0)
35(95.0)
23.9(75.0)
Rated Heating
21.1(70.0)
15.6(60.0)
8.3(47.0)
6.1(43.0)
2
Multi Variable Air Conditioners Ducted Type Indoor Unit
3 Preparations for Installation
Note: Product graphics are only for reference. Please refer to actual products. Unspecified
measure unit is mm/in.
3.1 Standard Fittings
Please use the supplied standard fittings listed below as instructed.
No.
Name
Appearance
Q'ty
Usage
1
Wired Controller
1
To control the indoor unit
2
Special Nut
1
To be used for connecting the
refrigerant pipe
3
M10X8 Nut with Washer
4
To be used together with the
hanger bolt for installing the unit.
4
M10 Nut (M10X8.4 Nut)
8
To be used together with the
hanger bolt for installing the unit.
5
M10 Washer (Spring
Washer M10X2.6)
4
To be used together with the
hanger bolt for installing the unit.
6
M10 Washer (M10Xφ30X
2.5)
4
To be used together with the
hanger bolt for installing the unit.
7
Insulation
1
To insulate the gas pipe
8
Insulation
1
To insulate the liquid pipe
9
Fastener
8
To fasten the sponge
10
Hanger
4
To fix the indoor unit
11
M8 Nut (M8X6.8)
8
To fix the hook on the cabinet of
the unit.
12
M8 Washer (Spring
Washer M8X2.1)
8
To fix the hook on the cabinet of
the unit.
14
M8 Washer
(M8Xφ16X1.5)
8
To fix the hook on the cabinet of
the unit.
15
paper pattern for
installation
1
Locate the drill hole on ceiling
or
3
Multi Variable Air Conditioners Ducted Type Indoor Unit
3.2 Location for Installation
(1) The appliance shall not be installed in the laundry.
(2) The top holder must be strong enough to support unit’s weight.
(3) Drain pipe can drain water out easily.
(4) There is no obstacle at inlet or outlet. Please ensure good air circulation.
(5) In order to make sure the space for maintenance, please install the indoor unit according
to the dimension described below.
(6) Keep the unit away from heating source, inflammable gas or smoke.
(7) This is a concealed ceiling type unit.
(8) Indoor unit, outdoor unit, power cord and electric wire should stay at least 1m (39-3/8 in.)
from the TV set and radio. Otherwise, these electrical appliances may have image
interference and noise. (Even if the distance is 1m (39-3/8 in.), when there is strong
electric wave, noise may still occur.)
Unit: mm/in.
Fig 3.2
(1) Installation of the unit must be in accordance with National Electric Codes and local regulations.
(2) Improper installation will affect unit’s performance, so do not install the unit by yourself. Please contact
local dealer to arrange professional technicians for the installation.
(3) Do not connect power until all installation work is finished.
3.3 Requirements for Communication Line
Note:
If air conditioner used under strong electronic-magnetic interference circumstance,
STP (shielded twisted pair) communication cable must be adopted.
4
Multi Variable Air Conditioners Ducted Type Indoor Unit
3.3.1 Select communication Line for Indoor Unit and Wired Controller
Fig 3.3.1
Wire type
Light/Ordinar
y polyvinyl
chloride
sheathed
cord. (60227
IEC 52
/60227 IEC
53)
Total length of
communication wire between
indoor unit and wired
controller (m/ft.)
L≤250m
(L≤820-1/5ft.)
Wire diameter
(mm2/AWG)
2×0.75~2×1.25
(2×AWG18~2×
AWG16)
Wire standard
Remark
IEC 60227-5
1. Total length of
communication line can't
exceed 250m (820-1/5ft.).
2. The cord shall be Circular
cord (the cores shall be
twisted together).
3. If unit is installed in places
with intense magnetic field
or strong interference, it is
necessary to use shielded
wire.
3.3.2 Select Communication Line for Indoor Unit and Outdoor Unit
Fig 3.3.2
Wire type
Light/Ordinary
polyvinyl
chloride
sheathed cord.
(60227 IEC 52
/60227 IEC 53)
Total length of
communication wire between
indoor unit and indoor
unit(outdoor unit) (m/ft.)
L≤1000m
(L≤3280-5/6ft.)
Wire diameter
(mm2/AWG)
≥2×0.75
(≥2×AWG18)
5
Wire standard
Remark
IEC 60227-5
1. If the wire diameter is
enlarged to 2×1 mm 2
(2×AWG16), the total
communication line length
can reach 1500 m
(4921-1/4ft.).
2. The cord shall be Circular
cord (the cores shall be
twisted together).
3. If unit is installed in places
with intense magnetic field
or strong interference, it is
necessary to use shielded
wire.
Multi Variable Air Conditioners Ducted Type Indoor Unit
3.4 Wiring Requirements
(1) Power Cord Size and Air Switch Capacity
Model
GMV-ND72PH/A-T(U)
GMV-ND96PH/A-T(U)
Power Supply
MCA(A)
MOP(A)
6.3
15
7.5
15
208/230V-1ph-60Hz
(1) Use copper wire only as unit’s power cord. Operating temperature should be within its rated value.
(2) If the power cord is more than 15 m (49-1/4 ft.) long, please increase properly the sectional area of power
cord to avoid overload, which may cause accident.
(3) Above selection requirements: Power cord size is based on BV single-core wire (2~4pc) at 40° (104°F)
Ambient temperature when laying across plastic pipe. Air switch is D type and used at 40°C (104°F). If
actual installation condition varies, please lower the capacity appropriately according to the specifications
of power cord and air switch provided by manufacturer.
(4) Install cut-off device near the unit. The minimum distance between each stage of cut-off device should be
3 mm (1/8 in.) (The same for both indoor unit and outdoor unit).
4 Installation Instructions
Note:
This series duct type unit is only for one room.
4.1 Installation of Indoor Unit
4.1.1 Outline Dimension and Installation Spots
Equip with an inspection hatch after lifting the unit. For the convenience of maintenance, the
service port should be on one side of the electric box and below unit’s lower level.
(1) Below are the outline dimension applicable to indoor units
Fig 4.1.1
Below are dimensions of A, B, C, etc. for different models:
Unit: mm/in.
Model
A
B
C
D
E
F
GMV-ND72PH/A-T(U)
1353
(53-1/4)
632
(24-7/8)
992
(39)
1150
(45-1/4)
192
(7-1/2)
327
(12-7/8)
GMV-ND96PH/A-T(U)
1563
(61-1/8)
706
(27-3/4)
992
(39)
1350
(53-1/8)
192
(7-1/2)
402
(15-7/8)
6
Multi Variable Air Conditioners Ducted Type Indoor Unit
(2) Drill bolt holes and install bolts
1) Stick the reference cardboard on the installation position; drill 4 holes according to the
hole site on the cardboard as shown in fig 4.1.2; diameter of drilling hole is according to
the diameter of expansion bolt and the depth is 60-70mm(2-3/8~2-3/4 in.), as shown in
fig 4.1.3.
Fig 4.1.2
Fig 4.1.3
2) Insert the M10 expansion bolt into the hole and then knock the nail into the bolt, as
shown in fig 4.1.4.
Note:
The length of bolt depends on the installation height of the unit, bolts are field supplied.
Fig 4.1.4
(3) Install the indoor unit temporarily
Assemble suspension bolt on the expansion bolt, attach the hanger bracket to the suspension
bolt. Be sure to fix it securely by using a nut and washer from upper and lower sides of the hanger
bracket. The washer fixing plate will prevent the washer from falling.
(4) The usage of paper pattern
Refer to paper pattern of installation for ceiling opening dimension. The center of ceiling
opening is indicated on the paper pattern. Fix the paper pattern to the unit with 4 screws and fix
the corners of the waterspout at the drainage pipe by screws.
(5) Adjust the unit to the right position.
(6) Check the level of the unit
The indoor unit is equipped with build-in water pump and float switch, verify the levelness of 4
directions by level gauge or vinyl tube (filled with water) respectively.
7
Multi Variable Air Conditioners Ducted Type Indoor Unit
Fig 4.1.5
(7) Remove the washer locating plate and then tighten the nut on it.
(8) Remove the paper pattern.
Fig 4.1.6
4.2 Refrigerant Pipe Connection
(1) Aim the flaring port of copper pipe at the center of screwed joint and then tighten the
flaring nut with hand as shown in fig 4.2.
(2) Tighten the flaring nut with torque wrench.
Torque for tightening nut
Pipe diameter mm(in.)
Torque (N·m)
9.52(3/8)
35-40
15.9(5/8)
60-65
19.04(3/4)
70-75
Fig.4.2
(3) Use pipe bend when bending the pipe and the bending angle should not be too small.
(4) Wrap the connection pipe and joint with sponge and then tie them firmly with tape.
8
Multi Variable Air Conditioners Ducted Type Indoor Unit
4.3 Drainage Pipe Installation and Drainage System Testing
4.3.1 Notice for Installation of Drain Pipe
(1) The drainage pipe should be short and the gradient downwards should be at least 1%~2%
in order to drain condensation water smoothly.
(2) The diameter of drainage hose should be bigger or equal to the diameter of drainage
pipe joint.
(3) Install drainage pipe according to the following fig and arrange insulation to the drainage
pipe. Improper installation may lead to water leakage and damp the furniture and other
things in the room.
(4) You can buy normal hard PVC pipe used as the drainage pipe. During connection, insert
the end of PVC pipe into the drainage hole and then tighten it with drainage hole and
wire binder. Can’t connect the drainage hole and drainage hole with glue.
(5) When the drainage pipelines are used for several units, the position of pipeline should
be about 100mm (4 in.) lower than the drainage port of each unit. In this case, thicker
pipes should be applied.
Fig 4.3.1
4.3.2 Drainage Pipe Installation
(1) Insert the drain hose into the drain hole and tighten it with tapes, as shown in Fig 4.3.2.
(2) Tighten the pipe clamp, with the distance between screw nut and hose smaller than
4mm (3/16 in.).
① metal clamp(accessory)
② drain hose(accessory)
(3) Use sealing plate to make the pipe clamp and hose insulated, as shown in Fig.4.3.3.
① metal clamp(accessory)
② thermal sponge(accessory)
Fig 4.3.2
Fig 4.3.3
(4) When connecting several drain pipes, follow the instruction as indicated in Fig 4.3.4.
Choose the drain collecting pipe that matches with unit capacity.
9
Multi Variable Air Conditioners Ducted Type Indoor Unit
Fig 4.3.4
(5) Install the trap as shown in following Fig 4.3.5.
(6) Install one trap for each unit.
(7) Convenience for cleaning trap in the future should be considered when installing it.
Fig 4.3.5
(8) The horizontal pipe can be connected to vertical pipe in the same level; please select
the connection way as shown in following fig.
NO1: Connection of drainage pipe joints (Fig4.3.6)
NO2: Connection of downspout elbow (Fig4.3.7)
NO3: Inserting pipe connection (Fig4.3.8)
Fig 4.3.6
Fig 4.3.7
Fig 4.3.8
(10) Drain pipes should have a downward slope of at least 1%~2%, in order to prevent pipes
from sagging, install hanger bracket at intervals of 1000~1500 mm (39-3/8~59 in.).
Fig 4.3.10
4.3.3 Test of Drainage System
(1) Inject approximately 1L purified water to drain pan from air vent, ensure that not to
splash the water over the electrical components (e.g. water pump. etc).
(2) During the test, please carefully check the drainage joint, make sure no any leakage
10
Multi Variable Air Conditioners Ducted Type Indoor Unit
occur.
(3) It is strongly recommend to do the drain test before ceiling decoration.
Fig 4.3.11
4.4 Installation of Air Duct
Note:
① There should be insulating layer on air-out duct, air-return duct and fresh air duct to
avoid heat loss and moisture. Adhere a nail on the air duct and then add thermal
sponge with a layer of tin. Fasten it with a nail cover and then seal the junction with tin
tapes. You can also use other materials that have good insulation quality.
② Each air-out duct and air-return duct should be fixed on a pre-made board with iron
frame. The junction of air duct should be well-sealed in order to prevent air leakage.
③ The design and construction of air duct should comply with national requirements.
④ The edge of air-return duct is suggested to be more than 150mm(5-7/8 in.) away from
the wall. Add a filter to the air-return opening.
⑤ Please consider noise-damping and vibration damping for the design and construction
of air duct. Besides, noise source must be away from people. For instance, do not have
the air-return opening installed on top of the user (Offices, rest area, etc.).
4.4.1 Installation of Air-out Duct
(1) Installation of the Rectangular Duct
Fig 4.4.1
11
Multi Variable Air Conditioners Ducted Type Indoor Unit
No.
Name
No.
Name
1
Hanger Rod
5
Static Pressure Box
2
Return Air Duct
6
Main Supply Air Duct
3
Canvas Duct
7
Supply Air Outlet
4
Return Air Inlet
4.4.2 Shape and Size of Air Outlet and Air-return Opening
Fig 4.4.2 Air Outlet
Fig 4.4.3 Air-return Opening
Unit: mm/in.
Model
GMV-ND72PH/A-T(U)
GMV-ND96PH/A-T(U)
Size of Air Outlet
Size of
Air –return
Opening
A
B
C
D
192
(7-1/2)
192
(7-1/2)
992
(39)
992
(39)
1150
(45-1/4)
1350
(53-1/8)
327
(12-7/8)
402
(15-7/8)
4.5 Installation of Wired Controller
Please refer to User Manual of Wired Controller for the installation details.
NOTICE! When installation is finished, the unit must be tested and debugged before
operation. Please refer to Instruction Manual of ODU for auto addressing and debugging
details.
4.6 External Static Pressure Settings
Unit parameters can be set in unit ON or OFF status.
(1) Long press FUNCTION button for 5s and the temperature zone displays “C00”; long press
FUNCTION button for another 5s to enter the interface of setting wired controller parameters.
“P00” is displayed in temperature zone;
(2) Press “▲” or “▼” button to select parameter code. Press MODE button to enter
12
Multi Variable Air Conditioners Ducted Type Indoor Unit
parameter setting. At that time, parameter value is blinking. Press “▲” or “▼” button to adjust
the parameter value and press ENTER/CANCEL button to finish setting.
(3) Press ENTER/CANCEL button to return to last step until exists setting parameters.
The parameter setting list is as following
Parameter code
P30
Parameter name Parameter range
Set static
pressure of
indoor fan motor
01-09: static
pressure level of
indoor fan motor
Default value
Note
05
There are two kinds of static pressure
level:
5 levels: 03, 04, 05, 06, 07
9 levels: 01, 02, 03, 04, 05, 06, 07,
08, 09
Static pressure level range is different
for different models; the wired
controller will automatically select
static pressure level range of indoor
fan motor according to the model of
indoor unit.
Note:
(1) Under parameter setting status, FAN, TIMER, SLEEP and SWING button are invalid.
Press ON/OFF button to go back to home page, but not turning on/off the unit.
(2) If the power cord is more than 15 m (49-1/4 ft.) long, please increase properly the sectional
area of power cord to avoid overload, which may cause accident.
External Static Pressure
static pressure level of indoor fan motor
0.28 inWG(70 Pa)
01
0.36 inWG(90 Pa)
02
0.44 inWG(110 Pa)
03
0.52 inWG(130 Pa)
04
0.60 inWG(150 Pa)
05
0.64 inWG(160 Pa)
06
0.68 inWG(170 Pa)
07
0.72 inWG(180 Pa)
08
0.80 inWG(200 Pa)
09
Note:
(1) Keep in mind that a shortage of airflow quantity or water leakage will result because the air
conditioner will be operated outside the rated range of airflow quantity if the external static
pressure is wrongly set.
(2) The Sound Pressure Level will change if the external static pressure is wrongly set.
5 Wiring Work
WARNING
Before obtaining access to terminals, all supply circuits must be disconnected.
(1) Units must be earthed securely, or it may cause electric shock.
(2) Please carefully read the wiring diagram before carry out the wiring work, incorrect wiring could cause
malfunction or even damage the unit.
(3) The unit should be powered by independent circuit and specific socket.
(4) The wiring should be in accordance with related regulations in order to ensure the units reliable running.
(5) Install circuit breaker for branch circuit according to related regulations and electrical standards.
13
Multi Variable Air Conditioners Ducted Type Indoor Unit
(6) Keep cable away from refrigerant pipings, compressor and fan motor.
(7) The communication wires should be separated from power cord and connection wire between indoor unit
(8) Adjust the static pressure via wired controller according to site circumstance.
5.1 Connection of Wire and Patch Board Terminal
(1) The connection of wire (as shown in fig 5.1.1)
1) Strip about 25mm (1 in.) insulation of the wire end by stripping and cutting tool.
2) Remove the wiring screws on the terminal board.
3) Shape the tail of wire into ring by needle nose plier, and keep the gauge of ring in
accordance with screw.
4) Use the screwdriver for tightening the terminal.
(2) The connection of stranded wire (as shown in fig 5.1.2)
1) Strip about 10mm (3/8 in.) insulation of the end of stranded wire by stripping and cutting
tool.
2) Loosen the wiring screws on terminal board.
3) Insert the wire into the ring tongue terminal and tighten by crimping tool.
4) Use the screwdriver for tightening the terminal.
Fig 5.1.1
Fig 5.1.2
5.2 Power Cord Connection
NOTICE! Every unit should be equipped with a circuit breaker for short-circuit and
overload protection. During operation, all indoor units connected to the same outdoor
unit system must be kept energized status. Otherwise, the unit can’t operate normally.
Fig 5.2
● For units with single-phase power supply.
(1) Detach the electric box lid.
(2) Let the power cord pass through the wiring through-holes.
14
Multi Variable Air Conditioners Ducted Type Indoor Unit
(3) Connect the power cord to terminal "L1, L2,
“
(4) Fix the power card with wiring clamp.
5.3 Connection of Communication Wire between Indoor Unit and Outdoor
Unit (or indoor unit)
(1) Detach the electric box lid.
(2) Let the Communication cable pass through the wiring through-holes.
(3) Connect the communication wire to terminal D1 and D2 of indoor 4-bit wiring board, as
shown in fig5.3.1.
Fig 5.3.1
Fig 5.3.2
(4) Fix the communication cable with clamp of electric box.
(5) For more reliable communication, make sure connect the terminal resistor to the most
downstream IDU of the communication bus (terminal D1 and D2), as shown in fig 5.3.2,
terminal resistor is provided with each ODU.
5.4 Connect Communication Wire of Wired Controller
(1) Open electric box cover of indoor unit.
(2) Let the communication wire go through the rubber ring.
(3) Connect the communication wire to terminal H1 and H2 of indoor 4-bit wiring board.
(4) Fix the communication wire with wire clip on the electric box.
(5) Wiring instructions of remote receiving light board and wired controller:
1) Fig 5.4.1 shows the installation of wired controller.
Fig 5.4.1
Fig 5.4.2
2) Fig 5.4.2 shows the installation of remote controller.
3) Wired controller and receiving light board can be installed at the same time. When
operating through a remote controller, both wired controller and the receiving light
board can receive the signals, as shown in Fig 5.4.3.
15
Multi Variable Air Conditioners Ducted Type Indoor Unit
Fig 5.4.3
5.5 Illuminate for Connection of Wired Controller and Indoor Units
Network
(1) Communication wire of indoor unit and outdoor unit (or indoor unit) is connected to D1,
D2.
(2) Wired controller is connected to H1, H2.
(3) One indoor unit can connect two wired controllers that must be set as master one and
slave one.
(4) One wired controller can control 16 indoor units in maximum at the same time. (As
shown in fig5.5)
(1) The type of indoor units must be the same if they are controlled by the same wired controller.
(2) When the indoor unit is controlled by two wired controllers, the addresses of the two wired controllers should
be different through address setting. Address 1 is for main controller; Address 2 is for slave controller.
Detailed setting please refer to the instruction manual of wired controller.
16
Multi Variable Air Conditioners Ducted Type Indoor Unit
Fig 5.5
17
Multi Variable Air Conditioners Ducted Type Indoor Unit
6 Routine Maintenance
(1) Do turn off the unit and cut off the main power supply when cleaning the air conditioner to avoid electric
shock or injury.
(2) Stand at solid table when cleaning the unit.
(3) Do not clean the unit with hot water whose temperature is higher than 45°C to prevent fade or deformation.
(4) Do not dry the filters by fire, or it may catch fire or become deformed.
(5) Clean the filter with a wet cloth dipped in neutral detergent.
(6) Please contact after-sales service staff if there is abnormal situation.
6.1 Cleaning of Filter
(1) Remove the filters from inlet of IDU. Use a vacuum cleaner to remove dust. If the filters
are dirty, wash them with warm water and mild detergent, and dry the filters in the shade.
(2) If the unit used in the environment with much dust, please clean it regularly. (Usually
once every two weeks).
6.2 Maintenance before the Seasonal Use
(1) Check if the air inlet and air outlet of indoor and outdoor unit are blocked.
(2) Check if securely grounded.
(3) Check if all the power cord and communication cable are securely connected.
(4) Check if any error code displayed after energized.
6.3 Maintenance after the Seasonal Use
(1) Set the unit in fan mode for half a day in a sunny day to dry the inner part of unit;
(2) When the unit won’t be used for a long time, please cut off power supply for energy
saving; the characters on the wired controller screen will disappear after cutting off the
power supply.
18
Multi Variable Air Conditioners Ducted Type Indoor Unit
7 Table of Error Codes for Indoor Unit
Error
Code
Error
Code
Content
Content
Error
Code
L0
Indoor Unit Error
LA
Indoor Units
Incompatibility Error
d9
L1
Indoor Fan Protection
LH
Low Air Quality Warning
dA
L2
E-heater Protection
LC
ODU-IDU Incompatibility
Error
dH
L3
Water Full Protection
d1
Indoor Unit PCB Error
dC
L4
Wired Controller Power
Supply Error
d3
L5
Freeze protection
d4
L7
L8
L9
No Master Indoor Unit
Error
Power Insufficiency
Protection
Quantity Of Group
Control Indoor Units
Setting Error
db
Content
Jumper Cap Error
Indoor Unit Network
Address Error
Wired Controller PCB
Error
Capacity DIP Switch
Setting Error.
Outlet Air Temperature
Sensor Error
Indoor Unit CO2 Sensor
Error
Water Temperature
Sensor Error
Ambient Temperature
Sensor Error
Inlet Pipe Temperature
Sensor Error
Outlet Pipe Temperature
Sensor Error
dE
d7
Humidity Sensor Error
C0
Communication Error
d8
Water Temperature
Error
AJ
Filter Cleaning Reminder
d6
dL
dy
Special Code: Field Debugging Code
8 Troubleshooting
The air conditioner is not expected to be serviced by users. Incorrect repair may cause
electric shock or fire, so please contact an authorized service center for professional service. The
following checks prior to contact may save your time and money.
Phenomenon
The unit can’t start
Troubleshooting
①
②
③
④
The unit stops after running
for a while.
Power supply is not connected.
Circuit breaker tripping caused by leakage of electricity.
Input voltage is too low.
Defect of main PC-board.
The inlet or outlet of ODU or IDU are blocked by obstacle.
Poor cooling effect
①
②
③
④
⑤
⑥
The filter is dirty.
Too heavy heat load of room(e.g. too many people)
Door or windows is open.
Inlet and outlet of IDU are blocked.
Setting temperature is too high.
Refrigerant is insufficient (e.g. refrigerant leakage)
Poor heating effect
①
②
③
④
The filter is dirty.
Door or window is open.
Setting temperature is too low.
Refrigerant is insufficient (e.g. refrigerant leakage)
Indoor fan doesn’t start
up during heating
① At starting, the IDU fan could not operate till the heat exchange become hot, for
preventing delivering the cool air.
② At defrosting, the IDU fan stopped due to system switch to cooling mode. For
preventing delivering the cool air, and resume operating after defrosting.
Note:
If air conditioner still fails to work normally after checking and handling as described above,
please stop using it immediately and contact local service center for assistance.
19
0DWHULDO6XSSO\,QFGED$&3UR
Add: ,QGXVWU\$YH)RQWDQD&$86$
Tel: E -mail: ZZZDFSURFRP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement