Samsung PCJ611RF User's Manual

Add to my manuals
58 Pages

advertisement

Samsung PCJ611RF User's Manual | Manualzz

00583F(E)-FRONT COVER 7/19/05 10:37 AM Page 1

PCJ532RF/PCJ533RF

PCJ534RF/PCJ611RF

PCJ614RF/PCK5315R

PCK6115R

COLOR TELEVISION

ELECTRONICS

AA68-00583F(ENG)

.............

Owner’s

Instructions

00583F(E)-Inside Front Cover 7/19/05 2:47 PM Page 1

Warning! Important

Safety Instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

Note to CATV system installer: This reminder is provided to call CATV system installer’s attention to Article 820-40 of the National Electrical Code (Section 54 of

Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to operate it.

Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug.

Attention: pour eviter les chocs electriques, introduire la lame le plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’au fond.

Important: One Federal Court has held that unauthorized recording of copyrighted TV programs is an infringement of U.S. copyright laws.

Certain Canadian programs may also be copyrighted and any unauthorized recording in whole or in part may be in violation of these rights.

To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

00583F(E)-PREFACE 7/19/05 2:47 PM Page 1

Thank You for Choosing Samsung

Thank you for choosing Samsung! Your new Samsung Projection TV represents the latest in television technology. We designed it with easy-to-use on-screen menus and closed captioning capabilities, making it one of the best products in its class. We are proud to offer you a product that will provide convenient, dependable service and enjoyment for years to come.

Important Safety Information

Always be careful when using your TV receiver. To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind when installing, using, and maintaining your machine.

• Read all safety and operating instructions before operating your TV.

• Keep the safety and operating instructions for future reference.

• Heed all warnings on the TV receiver and in the operating instructions.

• Follow all operating and use instructions.

• Unplug the TV receiver from the wall outlet before cleaning. Use a damp cloth; do not use liquid or aerosol cleaners.

• Never add any attachments and/or equipment without approval of the manufacturer. Such additions can increase the risk of fire, electric shock, or other personal injury.

• Do not use the TV receiver where contact with or immersion in water is a possibility, such as near bath tubs, sinks, washing machines, swimming pools, etc.

• Do not place the TV on an unstable cart, stand, tripod, bracket, or table where it can fall. A falling TV can cause serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the TV. Follow the manufacturer’s instructions when mounting the unit, and use a mounting accessory recommended by the manufacturer. Move the TV and cart with care.

Quick stops, excessive force, and uneven surfaces can make the unit and cart unsteady and likely to overturn.

• Provide ventilation for the TV receiver. The unit is designed with slots in the cabinet for ventilation to protect it from overheating. Do not block these openings with any object, and do not place the TV receiver on a bed, sofa, rug, or other similar surface. Do not place it near a radiator or heat register. If you place the TV receiver on a rack or bookcase, ensure that there is adequate ventilation and that you’ve followed the manufacturer’s instructions for mounting.

• Operate your TV receiver only from the type of power source indicated on the marking label.

If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company.

• Use only a grounded or polarized outlet. For your safety, this TV is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still does not fit, contact your electrician to replace your outlet.

S

AFETY

1

00583F(E)-PREFACE 7/19/05 2:47 PM Page 2

2

S AFETY

• Protect the power cord. Power supply cords should be routed so that they won’t be walked on or pinched by objects placed on or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit.

• Unplug the TV from the wall outlet and disconnect the antenna or cable system during a lightning storm or when left unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and power-line surges.

• Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines can be fatal.

• Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.

• Do not insert anything through the openings in the unit, where they can touch dangerous voltage points or damage parts. Never spill liquid of any kind on the TV.

• Ground outdoor antennas. If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code,

ANSI/NFPA No.70-1984, provides information about proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF

ANTENNA GROUNDING

ANTENNA

LEAD IN WIRE

GROUND CLAMP

ELECTRIC

SERVICE

EQUIPMENT

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING

CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

NEC — NATIONAL ELECTRICAL CODE

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

• Do not attempt to service the TV yourself. Refer all servicing to qualified service personnel.

Unplug the unit from the wall outlet and refer servicing to qualified service personnel under the following conditions:

- when the power-supply cord or plug is damaged

- if liquid has been spilled on the unit or if objects have fallen into the unit

- if the TV has been exposed to rain or water

- if the TV does not operate normally by following the operating instructions

- if the TV has been dropped or the cabinet has been damaged

- when the TV exhibits a distinct change in performance

• If you make adjustments yourself, adjust only those controls that are covered by the operating instructions. Adjusting other controls may result in damage and will often require extensive work by a qualified technician to restore the TV to normal.

• When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.

Unauthorized substitutions may result in additional damage to the unit.

• Upon completion of any service or repairs to this TV, ask the service technician to perform safety checks to determine that the TV is in a safe operating condition.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference that may cause undesired operation.

This television receiver provides display of television closed captioning in accordance with

§15.119 of the FCC rules.

g h nmp

-

20)

21)

DING he

00583F(E)-PREFACE 7/19/05 2:47 PM Page 3

FCC Information

User Instructions

The Federal Communications Commission Radio

Frequency Interference Statement includes the following warning:

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interf e rence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation .

If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

User Information

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

If necessary, consult your dealer or an experienced radio/television technician for additional suggestions.

You may find the booklet called How to Identify and

Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal Communications

Commission. It is available from the U.S. Government

Printing Office, Washington, DC 20402, Stock Number

004-000-00345-4 .

Warning

User must use shielded signal interface cables to maintain FCC compliance for the product.

Declaration of conformity for products marked with

FCC Logo. This device complies with Part 15 of the

FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

The party responsible for product compliance:

SAMSUNG ELECTRONICS CO., LTD

America QA Lab of Samsung

85 West Tasman Drive

San Jose, CA 95134 USA

Tel) 408-544-5124

Fax) 408-544-5191

Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating.

For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type

(parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with

NEMA configuration 6015P type (tandem blades) plug cap.

IC Compliance Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations of ICES-003.

Notice de Conformité IC

Cet appareil numérique de classe B respecte toutes les exigences du Règlement ICES-003 sur les équipements produisant des interférences au Canada.

MPR II Compliance

This monitor complies with SWEDAC (MPR II) recommendations for reduced electric and magnetic fields.

European Notice

Products with the CE Marking comply with both the

EMC Directive (89/336/EEC), (92/31/EEC),

(93/68/EEC) and the Low Voltage Directive

(73/23/EEC) issued by the Commission of the European

Community. Compliance with these directives implies conformity to the following European Norms:

• EN55022 (CISPR 22) – Radio Frequency Interference

• EN50082-1 : 1992 – Electromagnetic Immunity

• EN60555-2 (IEC555-2) – Power Line Harmonics

• EN60555-3 (IEC555-3) – Voltage Fluctuations

• EN60950 (IEC950) – Product Safety.

S

AFETY

3

00583F(E)-CONTENTS 7/19/05 2:48 PM Page 1

C O N T E N T S

Chapter 1: Your New TV . . . . . . . . . . . . . . .1.1

List of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.1

Familiarizing Yourself with Your New TV . . . . . . . . . . . . . . . . . . . . . 1.2

Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2

Front Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.3

Rear Panel Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.4

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5

Chapter 2: Installation . . . . . . . . . . . . . . . . 2.1

Connecting VHF and UHF Antennas . . . . . . . . . . . . . . . . . . . . . . . . 2.1

Antennas with 300-ohm Flat Twin Leads . . . . . . . . . . . . . . 2.1

Antennas with 75-ohm Round Leads . . . . . . . . . . . . . . . . . 2.2

Separate VHF and UHF Antennas. . . . . . . . . . . . . . . . . . . . 2.2

Connecting Cable TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2

Cable without a Cable Box . . . . . . . . . . . . . . . . . . . . . . . . . 2.2

Connecting to a Cable Box that Descrambles

All Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

Connecting to a Cable Box that Descrambles some Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3

Connecting a VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4

Connecting an S-VHS VCR. . . . . . . . . . . . . . . . . . . . . . . . . 2.5

Connecting a Second VCR to Record from Your TV . . . . . . 2.6

Connecting a Camcorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7

Installing Batteries in the Remote Control. . . . . . . . . . . . . . . . . . . . . 2.8

Chapter 3: Operation . . . . . . . . . . . . . . . . . . 3.1

Turning the TV On and Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1

Adjusting basic convergence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1

Adjust Red Convergence . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2

Adjust Blue Convergence . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2

Viewing the Menus and On-Screen Displays. . . . . . . . . . . . . . . . . . . 3.3

Viewing the Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3

Viewing the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3

Selecting a Menu Language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4

Memorizing the Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5

Selecting the Video Signal-source . . . . . . . . . . . . . . . . . . . . 3.5

Storing Channels in Memory (Automatic Method) . . . . . . . 3.6

Adding and Erasing Channels (Manual Method) . . . . . . . . 3.7

Changing Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7

Using the Channel Buttons. . . . . . . . . . . . . . . . . . . . . . . . . 3.7

Directly Accessing Channels. . . . . . . . . . . . . . . . . . . . . . . . 3.7

Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9

Using Mute. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.9

Customizing the Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.10

Using Automatic Picture Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.11

Customizing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.12

Using Automatic Sound Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.13

Viewing a VCR or Camcorder Tape. . . . . . . . . . . . . . . . . . . . . . . . . . 3.14

1

C ONTENTS

00583F(E)-CONTENTS 7/19/05 2:48 PM Page 2

C O N T E N T S

Chapter 4: Special Features . . . . . . . . . . . . 4.1

Customizing Your Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1

Setting Up Your Remote Control to Operate Your

VCR or DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1

Setting Up Your Remote Control to Operate Your

Cable Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2

Setting the On/Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4

Setting the Sleep Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5

Viewing Closed Captions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.6

Fine Tuning Channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.7

LNA(Low Noise Amplifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.8

Special Audio Options: Dolby Surround, MTS, and Headphones . . . 4.9

Dolby Prologic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.9

Dolby 3D Phonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.10

Choosing a Multi-Channel Sound (MTS) Soundtrack. . . . . 4.11

Using Wireless Headphones . . . . . . . . . . . . . . . . . . . . . . . . 4.12

Setting up Wireless Headphones with Picture-in-Picture. . . . 4.12

Viewing Picture-in-Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.13

Activating Picture-in-Picture. . . . . . . . . . . . . . . . . . . . . . . . 4.13

Selecting a Signal Source (Antenna or Cable) for PIP . . . . . 4.14

Selecting a Signal Source (External A/V) for PIP . . . . . . . . . 4.14

Swapping the Contents of the PIP image and Main image . 4.14

Changing the PIP Channel . . . . . . . . . . . . . . . . . . . . . . . . . 4.15

Changing the Location (Rotating) the PIP Window . . . . . . 4.15

Freezing the PIP Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.15

Changing the Size of the PIP Window . . . . . . . . . . . . . . . . 4.15

Scanning the Available Channels . . . . . . . . . . . . . . . . . . . . 4.15

Using the V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.16

Setting Up Your Personal ID Number (PIN) . . . . . . . . . . . . 4.16

How to Enable/Disable the V-Chip . . . . . . . . . . . . . . . . . . . 4.17

How to Set up Restrictions Using the “TV guidelines” . . . . 4.17

How to Set up Restrictions using the MPAA Ratings:

G, PG, PG-13, R, NC-17, X . . . . . . . . . . . . . . . . . . . . . . . . 4.19

How to Reset the TV after the V-Chip Blocks a Channel (“Emergency Escape”) . . . . . . . . . . . . . . . . . . . . 4.20

Chapter 5: Troubleshooting . . . . . . . . . . . . 5.1

Identifying Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1

Cleaning and Maintaining Your TV . . . . . . . . . . . . . . . . . . . . . . . . . . A.1

Using Your TV in Another Country . . . . . . . . . . . . . . . . . . . . . . . . . A.1

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.1

C

ONTENTS

2

00583F(E)-CHAPTER 1 7/19/05 2:29 PM Page 1

C h a p t e r O n e

Y O U R N E W T V

List of Features

Your Samsung TV was designed with the latest technology. This TV is a high-performance unit that includes the following special features:

• Easy-to-use remote control

• Easy-to-use on-screen menu system

• Automatic timer to turn the TV on and off

• Adjustable picture and sound settings that can be stored in the TV’s memory

• Automatic channel tuning for up to 181 channels

• A special filter to reduce or eliminate reception problems

• Fine tuning control for the sharpest picture possible

• A built-in multi-channel sound decoder for stereo and bilingual listening

• Built-in, dual channel speakers (20 watts per channel)

• A special sleep timer

• Picture-in-Picture

• Headphone jack for private listening

• 16:9 letter box format available depending upon source

1.1

C HAPTER O NE : Y OUR N EW TV

00583F(E)-CHAPTER 1 7/19/05 2:29 PM Page 2

Y O U R N E W T V

Familiarizing Yourself with The TV

Front Panel Buttons

The buttons on the front panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.

ΠPOWER

Press to turn the TV on and off.

´ TIMER indicator

When the TV is turned on, the TIMER indicator blinks ten times. This indicator illuminates when the TIMER mode is set to the “On” position after setting the clock and either the On timer or Off timer, with the remote control. Even if the power is turned off, this indicator stays lit. (Clock must be set before using this function.)

ˇ Remote Control

Sensor

Aim the remote control towards this spot on the TV.

¨ VOLUME – , +

Press to increase or decrease the volume. Also used to select items on the on-screen menu.

CH ▼ and CH

Press to change channels. Also press to highlight various items on the on-screen menu.

ˆ MENU

Press to see an on-screen menu of your TV's features.

Ø TV/VIDEO

Press this button to display a menu of all the available signal sources. When the menu appears, use the CH buttons to highlight a particular source, and then press VOL+ to select it.

C HAPTER O NE : Y OUR N EW TV

1.2

1

00583F(E)-CHAPTER 1 7/19/05 2:29 PM Page 3

Y O U R N E W T V

Front Panel Jacks

You can use the front panel jacks to connect an A/V component that is used only occasionally, such as a camcorder or video game. (For information on connecting equipment, see pages 2.1 – 2.7.)

2 1.3

C HAPTER O NE : Y OUR N EW TV

ΠSUPER VIDEO IN jack

Used to connect an S-Video signal from a camcorder or a video game.

´ VIDEO IN jack

Used to connect a video signal from a camcorder or a video game.

ˇ AUDIO IN jacks

Used to connect the audio signals from a camcorder or video game.

00583F(E)-CHAPTER 1 7/19/05 2:29 PM Page 4

Y O U R N E W T V

Rear Panel Jacks

Use the rear panel jacks to connect an A/V component that will be connected continuously, such as a VCR or a laserdisc player.

Because there are two sets of input jacks, you can connect two different A/V components (i.e., a VCR and a laserdisc, 2 VCRs, etc.)

For more information on connecting equipment, see pages 2.1 – 2.7.

ΠVHF/UHF

Connect to an antenna or to a cable TV system.

´ WIRELESS

HEADPHONES

Connect a pair of wireless headphones here (optional)

ˇ SUPER VIDEO IN

S-Video signal from an S-VHS

VCR or laserdisc player.

¨ VIDEO INPUTS

Video signals from VCRs, laserdisc players and similar devices (Two sets are available: Video1 and Video2).

ˆ AUDIO INPUTS

Audio signals from VCRs, laserdisc players and similar devices.

Ø AUDIO-VIDEO

MONITOR OUTPUTS

These audio-video signals are identical to

A/V signals being displayed on the big screen.

(Typically used as the input signals for a recording VCR.)

Note: The monitor out does not operate in DVD or

DTV mode.

DVD INPUT

Connect video from a DVD player.

DVD & DTV AUDIO INPUT

Connect to the audio output jacks of a DVD player & SET-TOP BOX.

DTV INPUT

(For models PCJ532RF/PCJ534RF/

PCJ611RF/PCJ614RF/PCK5315R/PCK6115R)

Connects video from a SET-TOP BOX.

˝ SURROUND OUT

Connects to the (optional) rear-surround amp: Surround Left,

Surround Right and Center.

Here are two ways to connect an audio amplifier:

1. TV - amp - speaker

2. TV - speaker(amp built-in).

C HAPTER O NE : Y OUR N EW TV

1.4

1

00583F(E)-CHAPTER 1 7/19/05 2:29 PM Page 5

Y O U R N E W T V

Remote Control

You can use the remote control up to about 23 feet from the TV. When using the remote, always point it directly at the TV.

You can also use your remote control to operate your VCR and cable box. See page 4.1

for details.

ΠPOWER

Turns the TV on and off.

´ ADD/ERASE

Press to add or erase channels in the TV’s memory.

ˇ PIP

Activates picture in picture.

¨ DISPLAY

Press to display the current channel and the audio-video settings.

ˆ Number buttons

Press to select channels directly on the TV.

Ø +100

Press to select channels over 100.

For example, to select channel 121, press “+100,” then press “2” and “1.”

P.MODE

Adjust the TV picture by selecting one of the preset factory settings (or select your personal, customized picture settings).

S.MODE

Adjust the TV sound by selecting one of the preset factory settings

(or select your personal, customized sound settings).

MUTE

Press to temporarily cut off the sound.

˝ CHand CH

(Channel Up/Down)

Press CH ▲ or CH▼ to change channels. (Also used to highlight selections on the on-screen menus.)

Ô MODE

Selects a target device to be controlled by the Samsung remote control (i.e., TV, VCR,

Cable box, or DVD).

3D PHONIC

Selects one of the 3D Phonic modes (Drama, Action or Theater).

Ò CAPTION

Controls the caption decoder.

Ú V.CHIP

Press to set up and activate the parental locks.

Æ PRE-CH

Tunes to the previous channel.

ı SLEEP

Press to select a preset time interval for automatic shutoff.

˜ MTS (Multichannel

Television Stereo)

Press to choose stereo, mono or

Separate Audio Program (SAP broadcast).

¯ TV/VIDEO

Press to display all of the available video sources (i.e.,

Antenna/cable, VCR, DVD,

Video1~3 and S-Video 1~2).

˘ MENU

Displays the main on-screen menu.

¿ VOL

-

, VOL

+

Press increase or decrease the volume. (Also used to make selections on the on-screen menus.)

(For model PCJ533RF)

4 1.5

C HAPTER O NE : Y OUR N EW TV

00583F(E)-CHAPTER 1 7/19/05 2:29 PM Page 6

Y O U R N E W T V

Remote Control (continued)

¸ VCR controls

REC

Press to begin recording. (Note:

A VCR must be connected.)

PAUSE

Press to pause the tape.

REW (Rewind)

Press to rewind a tape

STOP

Press to stop a tape in your VCR.

PLAY

Press to play the tape

FF (Fast Forward)

Press to fast forward a tape

˛ SET

Used during set up of this

Samsung remote control, so that it will work compatibly with other devices (VCR, cable box, etc.)

PIP Controls

TV/VIDEO

Press to select one of the available signal sources for the

PIP window.

ROTATE

Press to move the PIP window to any of the four corners of the TV screen.

P.SIZE

Press to make the PIP window larger or smaller.

SWAP

Exchanges the video signal that is currently displayed on the main screen with the signal in the PIP window.

PIP CH

Displays the available channels in sequence. (These buttons change channels in the

PIP window only).

STILL

Press to stop the action during a particular scene. Press again to resume normal video.

CH.SCAN

Press to memorize (scan) the available channels.

(For model PCJ533RF)

C HAPTER O NE : Y OUR N EW TV

1.6

1

00583F(E)-CHAPTER 1 7/19/05 2:29 PM Page 7

Y O U R N E W T V

Remote Control (continued)

ΠDTV

Press to activate a Digital TV Set-

Top Box. (When the DTV mode is active, all channel selections must be made using a separate remote control that is supplied with the set-top box.)

When pressing the DTV button, the DTV mode is selected after approximately 5 seconds.

Select either 1080i or 480p format for the set-top box output signal.

(Otherwise, the picture may flicker.)

´ ADD/ERASE

Press to add or erase channels in the TV’s memory.

6 1.7

C HAPTER O NE : Y OUR N EW TV

(For model PCJ532RF/PCJ534RF/

PCJ611RF/PCJ614RF/PCK5315R/

PCK6115R)

00583F(E)-CHAPTER 2 7/19/05 2:30 PM Page 1

2

C h a p t e r Tw o

I N S TA L L AT I O N

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like this, see “Antennas with

300-ohm Flat Twin Leads,” below.

If your antenna has one lead that looks like this, see “Antennas with 75-ohm

Round Leads,” on page 2.2.

If you have two antennas, see “Separate

VHF and UHF Antennas,” on page 2.2.

Antennas with 300-ohm Flat Twin Leads

If you are using an off-air antenna (such as a roof antenna or “rabbit ears”) that has

300-ohm twin flat leads, follow the directions below.

1

Place the wires from the twin leads under the screws on the 300-75 ohm adaptor (not supplied). Use a screwdriver to tighten the screws.

2

Plug the adaptor into the

VHF/UHF terminal on the bottom of the back panel.

C HAPTER T WO : I NSTALLATION

2.1

00583F(E)-CHAPTER 2 7/19/05 2:30 PM Page 2

I N S TA L L AT I O N

Antennas with 75-ohm Round Leads

1

Plug the antenna lead into the VHF/UHF terminal on the bottom of the back panel.

Separate VHF and UHF Antennas

If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires a an optional combiner-adaptor (available at most electronics shops).

1

Connect both antenna leads to the combiner.

2

Plug the combiner into the VHF/UHF terminal on the bottom of the rear panel.

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.

Cable without a Cable Box

1

Plug the incoming cable into the VHF/UHF antenna terminal on back of the TV.

Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.

2.2

C HAPTER T WO : I NSTALLATION

00583F(E)-CHAPTER 2 7/19/05 2:30 PM Page 3

I N S TA L L AT I O N

Connecting to a Cable Box that Descrambles All Channels

1

Find the cable that is connected to the

ANTENNA OUT terminal on your cable box.

This terminal might be labeled

“ANT OUT,” “VHF OUT,” or simply,

“OUT.”

2

Connect the other end of this cable to the

VHF/UHF antenna terminal on the back of the TV.

Connecting to a Cable Box that Descrambles Some Channels

If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two-way splitter, an RF (A/B) switch, and four lengths of coaxial cable. (These items are available at most electronics stores.)

1

Find and disconnect the cable that is connected to the ANTENNA IN terminal on your cable box.

This terminal might be labeled

“ANT IN,” “VHF IN,” or simply,

“IN.”

2

Connect this cable to a two-way splitter.

3

Connect a coaxial cable between an OUTPUT terminal on the splitter and the IN terminal on the cable box.

C HAPTER T WO : I NSTALLATION

2.3

00583F(E)-CHAPTER 2 7/19/05 2:30 PM Page 4

I

N S TA L L AT I O N

4

Connect a coaxial cable between the ANTENNA

OUT terminal on the cable box and the B–IN terminal on the A/B switch.

5

Connect another cable between the other OUT terminal on the splitter and the A–IN terminal on the RF (A/B) switch.

6

Connect the last coaxial cable between the OUT terminal on the RF (A/B) switch and the VHF/UHF terminal on the rear of the TV.

After you’ve made this connection, set the A/B switch to the “A” position for normal viewing.

Set the A/B switch to the “B” position to view scrambled channels. (When you set the A/B switch to “B,” you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)

Connecting a VCR

These instructions assume that you have already connected your TV to an antenna or a cable

TV system (according to the instructions on pages 2.1-2.3). Skip step 1 if you have not yet connected to an antenna or a cable system.

1

Unplug the cable or antenna from the back of the TV.

2

Connect the cable or antenna to the

ANTENNA IN terminal on the back of the VCR.

2.4

C HAPTER T WO : I NSTALLATION

g.

ule

00583F(E)-CHAPTER 2 7/19/05 2:30 PM Page 5

I N S TA L L AT I O N

3

Connect a coaxial cable between the ANTENNA

OUT terminal on the

VCR and the antenna terminal on the TV.

A coaxial cable is usually included with a VCR. (If not, check your local electronics store).

4

Connect a set of audio cables between the

AUDIO OUT jacks on the

VCR and the AUDIO jacks on the TV.

If you have a “mono” (non-stereo) VCR, use the Y-connector (supplied) to hook up to the left and right audio input jacks of the TV. If your VCR is stereo, you must connect two cables.

5

Connect a video cable between the VIDEO OUT jack on the VCR and the

VIDEO jack on the TV.

Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.

Connecting an S-VHS VCR

Your Samsung TV can be connected to an S-Video signal from an S-VHS VCR. (This connection delivers a better picture as compared to a standard VHS VCR.)

1

To begin, follow steps

1–3 in the previous section to connect the antenna or cable to your

VCR and your TV.

2

Connect a set of audio cables between the

AUDIO OUT jacks on the

VCR and the 2 AUDIO

INPUT jacks on the TV.

Make sure the jacks you are using are underneath the number “2.”

C HAPTER T WO : I NSTALLATION

2.5

00583F(E)-CHAPTER 2 7/19/05 2:30 PM Page 6

I N S TA L L AT I O N

3

Connect an S-video cable between the

S-VIDEO OUT jack on the VCR and the

S-VIDEO INPUT jack on the TV.

An S-video cable is usually included with an S-VHS VCR. (If not, check your local electronics store.)

Connecting a Second VCR to Record from the TV

Your TV can send out signals of its picture and sound to be recorded by a second VCR.

To do this, connect your second VCR as follows:

1

Connect a set of audio cables between the

AUDIO OUT jacks on the

TV and the AUDIO IN jacks on the VCR.

(The VCR input jacks might be either on the front or on back of the VCR.)

2

Connect a video cable between the VIDEO OUT jack on the TV and the

VIDEO IN jack on the

VCR.

Refer to your VCR’s instructions for more information about how to record using this kind of connection.

Connecting a Digital TV Set-Top Box

(For models PCJ532RF/PCJ534RF/PCJ611RF/PCJ614RF/PCK5315R/PCK6115R)

Connect the Y, Pb, and Pr video outputs of the set-top box to their corresponding inputs on the TV. Next, connect the Left and Right audio from the set-top box to the corresponding L and R terminals on the TV. (The connections for a typical set-top box are shown below.)

When switching to the DTV mode, either 480p or 1080i format is automatically selected according to the input signal.

Note: Only 480p and 1080i formats are supported in their original formats.

2.6

C HAPTER T WO : I NSTALLATION

00583F(E)-CHAPTER 2 7/19/05 2:30 PM Page 7

I N S TA L L AT I O N

Connecting a Camcorder

The front panel jacks on your TV make it easy to connect a camcorder to your TV. They allow you to view the camcorder tapes without using a VCR. (Also see “Viewing a VCR or

Camcorder Tape” on page 3.14)

1

Locate the A/V output jacks on the camcorder.

They are usually found on the side or back of the camcorder.

2

Connect an audio cable between the AUDIO

OUTPUT jack on the camcorder and the

AUDIO terminals on the front of the TV.

3

Connect a video cable between the VIDEO

OUTPUT jack on the camcorder and the

VIDEO terminal on the front of the TV.

The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) If your camcorder is stereo, you need to connect a set of two cables.

C HAPTER T WO : I NSTALLATION

2.7

00583F(E)-CHAPTER 2 7/19/05 2:30 PM Page 8

I N S TA L L AT I O N

Installing Batteries in the Remote Control

1

Slide the cover out completely.

2

Install two AAA size batteries.

Make sure to match the “ + ” and

– ” ends of the batteries with the diagram inside the compartment.

3

Replace the cover.

Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time.

The remote control can be used up to about 23 feet from the TV.

(Assuming typical TV usage, the

Batteries last for about one year.)

2.8

C HAPTER T WO : I NSTALLATION

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 1

C h a p t e r T h r e e

O P E R AT I O N

Turning the TV On and Off

Press POWER.

You can also use the POWER button on the front panel.

Adjusting Basic Convergence

If the color appears spread out or “smeared” on the screen, the convergence probably needs alignment. Be sure to use the remote control for the convergence adjustments. (The

Convergence Adjustment cannot be made by using the control buttons on the front panel.)

First steps:

1

Press MENU.

Press CH ▼ twice to highlight the Setup icon

(starts blinking).

2

Press VOL +.

Press CH

▼ three times to highlight “Convergence”

(the letters change to blue color).

3

Press VOL + : The

“Manual Convergence” screen will appear, and the word “Red” will be highlighted.

continued...

C HAPTER T HREE : O PERATION

3.1

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 2

O P E R AT I O N

Adjust Red Convergence

4

While “Red” is highlighted (letters are blue color), press the VOL+ button:

A crosshair pattern will appear on the screen. If either a vertical or a horizontal red line is visible, then the convergence needs alignment.

5

If a horizontal red line is visible, use CH ▲ and CH▼ buttons to move the line so that it is superimposed on the horizontal centerline (i.e., make a single horizontal line that is as white as possible.)

6

If a vertical red line is visible, use the VOL + and VOL - buttons to move the line so that it is superimposed on vertical-center line (i.e., make a single vertical line that is as white as possible.)

To do Left or Right Convergence

7

If the left adjustments need, press the number(4) button on the remote control to move the vertical red line to the left.

Use the VOL +/- to buttons to move the line to the right or left.

If the right adjustments need, press the number(6) button on the remote control to move the vertical red line to the right.

Use the VOL +/- to buttons to move the line to the right or left.

8

After the red convergence is correctly adjusted, press MENU four times to exit all the menus.

•For ‘Blue’ adjustment, do the same as the above.

Note: While the left and right adjustments are done, the

CH ▲ and CH▼ buttons will not work.

3.2

C HAPTER T HREE : O PERATION

e ot

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 3

O P E R AT I O N

Viewing the Menus and On-Screen Displays

Viewing the Menus

1

With the power on, press MENU.

The main menu appears on the screen. Its left side has five icons:

Video, Audio, Setup,

Dolby and PIP.

The on-screen menus disappear from the screen after about thirty seconds.

2

Use the CH

▲ and CH▼ buttons to highlight one of the 5 icons

(the icons blink when highlighted). Then press VOL+ to access the icon’s sub-menu.

3

Press MENU to exit.

You can also use the MENU,

CHANNEL, and VOLUME buttons on the control panel of the TV to make selections.

Viewing the Display

The display identifies the current channel and the status of certain audio-video settings.

1

Press the DISPLAY on the remote control.

The on-screen displays disappear after about ten seconds.

The TV will display the channel, the type of audio, and the status of certain video and audio settings.

(“MFT” indicates a channel has been manually fine tuned.)

C HAPTER T HREE : O PERATION

3.3

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 4

O P E R AT I O N

Selecting a Menu Language

1

Press MENU to display the menu.

Press CH

▼ two times to select “SET UP.”

2

Press VOL + to display the “SET UP” menu.

Press CH

▼ four times to highlight Language.

3

Press VOL + to select the appropriate language: English,

Spanish, or French.

Note: Language is selected depending on model (English and

Spanish or English and French).

4

Press MENU twice to exit.

3.4

C HAPTER T HREE : TV O PERATION

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 5

O P E R AT I O N

Memorizing the Channels

Your TV can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH

▲ and

CH

▼ buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels

(manual).

Selecting the Video Signal-source

Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e., an antenna or a cable system).

1

Press MENU to display the menu.

2

Press CH

▼ two times to highlight “SET UP.”

3

Press VOL +.

The setup sub-menu will appear. Press CH

▼ to highlight ANT/CATV.

4

Repeatedly press VOL + to cycle through these choices:

ANT (antenna)

STD, HRC or IRC (all cable TV).

Note: STD, HRC and IRC identify various types of cable TV systems.

Contact your local cable company to identify the type of cable system that exists in your particular area.

At this point the signal source has been selected. Proceed to “Storing

Channels in Memory” (next page).

C HAPTER T HREE : TV O PERATION

3.5

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 6

O P E R AT I O N

Storing Channels in Memory (Automatic Method)

1

First, select the correct signal source (ANT, STD,

HRC, IRC). See steps 1~4 on previous page.

Press MENU, then press

CH ▼ twice to highlight

“SET UP.”

Press VOL + to access the SETUP sub-menu.

“Channel set up” will be highlighted.

2

Press VOL + while

“Channel set up” is highlighted. A new sub-menu will appear, and “Auto program” will be highlighted.

3

Press VOL + again.

The TV will begin memorizing all of the available channels.

4

After all the available channels are stored, the

Auto program menu reappears. Press Menu three times to exit.

Note: Channel auto program does not function when the

V-chip is active.

The TV automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes.

Press VOL+ at any time to interrupt the memorization process and return to the Setup menu.

3.6

C HAPTER T HREE : TV O PERATION

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 7

O P E R AT I O N

Adding and Erasing Channels (Manual Method)

1

Use the number buttons to directly select the channel that will be added or erased.

2

Press ADD/ERASE:

Repeatedly pressing this button will alternate between

“Channel added” and “Channel erased.”

Press MENU to exit.

You can view any channel (including an erased channel) by using the number buttons on the remote control.

Changing Channels

Using the Channel Buttons

1

Press the CH

▲ or CH ▼ button to change channels.

When you press CH

▲ or CH ▼, the TV changes channels in sequence. You will see all the channels that the TV has memorized. (The TV must have memorized at least three channels.) You will not see channels that were either erased or not memorized.

Directly Accessing Channels

Use the number buttons to quickly tune to any channel.

1

Press the number buttons to go directly to a channel. For example, to select channel 27, press “2,” then “7.” The TV will change channels when you press the second number.

When you use the number buttons, you can directly select channels that were either erased or not memorized.

To select a channel over 100, press the +100 button. (For channel 122, press

“+100,” then “2,” then “2.”)

To change to single-digit channels (0–9) faster, press “0” before the single digit. (For channel “4,” press “0,” then “4.”)

C HAPTER T HREE : TV O PERATION

3.7

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 8

O P E R AT I O N

Setting the Clock

1

Press the MENU button to display the on-screen menu.

2

Press CH

▼ twice to highlight “SET UP.”

Press VOL +.

3

Press CH

▼ twice to highlight Time menu.

Press VOL + : The Time menu will appear on the screen, and “Clock” will be highlighted (blue color).

4

Press VOL + again (the hours digits will start blinking). Press CH

▼ repeatedly until the correct hour appears.

After the hour is entered, press VOL +

(at this point the minutes digits will start blinking).

5

Press the CH

▲ or CH ▼ button to select the correct minutes.

After selecting the correct minutes, press

VOL +.

6

Press MENU three times to exit.

3.8

C HAPTER T HREE : TV O PERATION

When selecting the hours, be sure to select the proper time of day (AM or PM).

You can change the hours by pressing

CH ▲ or CH ▼ repeatedly (or by holding down either of these buttons).

The time will appear every time you press DISPLAY.

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 9

O P E R AT I O N

Adjusting the Volume

1

Press VOL + or – VOL to increase or decrease the volume.

Using Mute

At any time, you can temporarily cut off the sound using the Mute button.

1

Press MUTE and the sound cuts off.

The word “Mute” will appear in the lower-left corner of the screen.

2

To turn mute off, press MUTE again, or simply press either the VOL – or VOL + button.

C HAPTER T HREE : TV O PERATION

3.9

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 10

O P E R AT I O N

Customizing the Picture

You can use the on-screen menus to change the contrast, brightness, tint, color, and sharpness according to personal preference. (Alternatively, you can use one of the

“automatic” settings. See next page.)

1

Press MENU to access the main menu.

The VIDEO icon will be highlighted (starts blinking).

2

Press VOL – or VOL + repeatedly, until the word

“Custom” is highlighted.

(When Custom is highlighted, the words

“Contrast,” “Brightness,”

“Sharpness,” “Color,” and

“Tint” will appear on the screen.)

3

Press CH ▼ or CH ▲ button to highlight a particular item.

After adjusting an item, the gauge will automatically disappear (after about 5 seconds).

4

Press VOL – or VOL + to increase or decrease the value of a particular item. For example, if you select “Brightness,” pressing VOL + increases it.

Press MENU twice to exit.

3.10

C HAPTER T HREE : TV O PERATION

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 11

O P E R AT I O N

Using Automatic Picture Settings

Your Samsung TV has two automatic picture settings (“Standard” and “Mild”) that are preset at the factory. You can activate either Standard or Mild by pressing P.Mode (or by making a selection from the menu). Or, you can select “Custom” which automatically recalls your personalized picture settings.

1

Press MENU to display the menu. Video icon will be highlighted

(blinking).

Press VOL + to display the VIDEO menu.

2

Press VOL - or VOL + to select the “Standard,”

“Mild,” or “Custom” picture setting.

3

Alternate method:

Simply press the P.MODE button on the remote control to select one of the standard picture settings.

• Choose Standard for the standard factory settings.

• Choose Mild (“Mild Contrast”) when viewing the TV in low light, or when playing video games.

• Choose Custom if you want to adjust the settings accordings to personal preference (see “Customizing the Picture, page 3.10).

C HAPTER T HREE : TV O PERATION

3.11

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 12

O P E R AT I O N

Customizing the Sound

You can use the on-screen menus to adjust the bass, treble, and balance according to individual preference. (Alternatively, you can use one of the “automatic” settings. See next page.)

1

Press MENU to display the menu.

Press CH

▼ to highlight the AUDIO icon

(starts blinking).

2

Press VOL - or VOL + repeatedly, until the word “Custom” is highlighted. (When Custom is highlighted, the words

“Bass,” “Treble,” and

“Balance” will appear on the screen.

3

Press the CH

▲ or CH ▼ buttons to highlight a particular item to be changed.

When you are finished adjusting an item, wait about 10 seconds. The gauge will disappear and the Audio menu will return.

4

Press VOL – or VOL + to increase or decrease the value of a particular item.

For example, if you select

“Bass,” pressing VOL + increases it.

Press MENU twice to exit.

3.12

C HAPTER T HREE : TV O PERATION

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 13

O P E R AT I O N

Using Automatic Sound Settings

Your TV has four automatic sound settings (“Standard,” “Music,” “Speech,” and “Movie”) that are preset at the factory. You can activate any of them by pressing the S.MODE button (or by making a selection from the on-screen menu). Or, you can select “Custom,” which automatically recalls your personalized sound settings.

1

Press MENU to display the menu.

Press CH

▼ once to highlight the AUDIO menu.

2

Press VOL - or VOL + repeatedly to select the

“Standard,” “Music,”

“Speech,” “Movie” or

“Custom” audio settings.

3

Alternate method:

Simply press the S.MODE button on the remote control to select one of the standard sound settings.

• Choose Standard for the standard factory settings.

• Choose Music when watching music videos or concerts.

• Choose Speech when watching a show that is mostly dialogue (i.e., news).

• Choose Movies when watching movies.

• Choose Custom to recall your personalized settings.

C HAPTER T HREE : TV O PERATION

3.13

00583F(E)-CHAPTER 3 7/19/05 2:32 PM Page 14

O P E R AT I O N

Viewing a VCR or Camcorder Tape

You must select the appropriate mode in order to view the VCR or

Camcorder signal on the TV.

1

Make sure that the remote control is controlling the TV set.

(Press the MODE button and make sure that the “TV” LED is illuminated.)

2

Press TV/VIDEO on the remote control, and the following onscreen menu will appear:

TV/Video Menu

ANT/CATV

Video1

Video2

Video3

S-Video1

S-Video2

DVD

3

Use the CH

▲ or CH▼ button to highlight a particular signal source, and then press VOL+ to activate it.

Press TV/VIDEO to exit.

When you press the TV/Video button, the on-screen display identifies all the active video sources (and their corresponding input jacks):

3.14

C HAPTER T HREE : TV O PERATION

00583F(E)-CHAPTER 4 7/19/05 2:34 PM Page 1

C h a p t e r F o u r

S P E C I A L F E AT U R E S

Customizing Your Remote Control

Your Samsung TV comes equipped with a “universal” remote control. In addition to controlling the TV, the universal remote can also operate a VCR, DVD and a cable box

(even if your VCR and cable box are made by manufacturers other than Samsung).

Setting Up Your Remote Control to Operate Your VCR

1

Turn off your VCR or

DVD.

2

Press the MODE button and make sure that the VCR LED is illuminated.

The remote control has four

“modes”: “TV,” “VCR”, “CABLE” and “DVD.” Press the “MODE” button to switch the remote control to the “VCR” mode.

3

On your Samsung remote control, press SET.

4

Enter 3 digits of the VCR code listed on the next page for your brand of VCR.

Make sure you enter 3 digits of the code, even if the first digit is a “0.”

If more than one code listed, try the first one.

5

Press POWER on the remote control. Your VCR should turn on. If your VCR turns on, your remote control is now set correctly.

If your VCR does not turn on, repeat steps 2, 3, and 4, but try one of the other codes listed for the brand of your particular VCR.

If no other codes are listed, try each code, 000 through 089.

6

Once your remote control is set up, press the MODE button any time you want to use the remote to operate your VCR.

When your remote control is in the “VCR” mode, the volume buttons still control your TV’s volume.

✓ Set the DVD mode in the same methods as above.

When your remote is in the “TV” mode, the VCR control buttons (PLAY,

PAUSE, etc.) will still operate your

VCR.

C HAPTER F OUR : S PECIAL F EATURES

4.1

00583F(E)-CHAPTER 4 7/19/05 2:34 PM Page 2

S

P E C I A L

F

E AT U R E S

VCR Codes

DVD Codes

Admiral

Aiwa

006, 079

015

Akai 017, 022, 023, 027, 030

Audio Dynamics 014, 016

Bell & Howell

Broksonic

Candle

Cannon

002

010

007, 009, 013, 045, 046, 052

008, 053

Citizen

Colortyme

007, 009, 013, 045, 046, 052

014

Craig

Curtis-Mathes

007, 012

000, 007, 008, 014,

015, 046, 053, 064, 067

Daewoo

DBX

Dimensia

Dynatech

013, 045, 076

014, 016

000

015

Electrohome

Emerson

027

008, 009, 010, 013, 015, 020, 023, 027,

034, 041, 042, 047, 049, 057, 062, 065, 067, 068, 070

Fisher 002, 012, 018, 019, 043, 048, 058

Funai

GE

Go Video

015

000, 007, 008, 032, 053

007

Harman Kardon

Hitachi

014

005, 015, 035, 036

Instant Replay

JC Penney

008

002, 005, 007, 008, 014,

JCL

JVC

Kenwood

016, 030, 035, 051, 053

008, 002, 014, 016, 030, 046

002, 014, 088, 089

002, 014, 016, 030, 046

Philips

Proscan

RCA

Toshiba

Panasonic

Sony

Samsung

001

002

002

003

004

008

000

KLH

LG

Lloyd

Logik

LXI

Magnavox

Marantz

073

009, 014, 046, 060

015

031

015

008, 029, 053, 056

002, 008, 014, 016,

029, 030, 046, 061

Marta

MEI

Memorex

MGA

Midland

Minota

Mitsubishi

009

008

008, 009, 012, 015

027

032

005, 035

005, 027, 035, 040

Montgomery ward

MTC

006

007, 015

Multitech

NEC

007, 015, 031, 032

002, 014, 016, 030, 046, 061, 064

Optimus

Panasonic

Pentax

Pentex Reserch+

Philco

006

008, 053, 075, 077

005, 035

046

008, 029, 053, 056

Philips

Pioneer

Portland

ProScan

008, 029

005, 016, 033, 050

044, 045, 052

000

Quartz

Quasar

002

008, 053

Radio Shack/Realist 002, 006, 008,

009, 012, 015, 019, 027, 045, 053

RCA

Samsung

Sansui

Sanyo

Scott

Sears

Sharp

Shintom

Signature

Sony

Sylvania

Symphonic

Tandy

Tashiko

Tatung

Teac

Technics

Ternika

TMK

Toshiba

Totevision

Unitech

000, 005, 007, 008, 028,

035, 037, 054, 069

007, 013, 022, 032, 042, 077

016

002, 012

013, 041, 049, 068

002, 005, 009, 012, 018,

019, 035, 043, 048

006, 027, 039, 045

017, 026, 031, 055

015

017, 026, 038

008, 015, 029, 053, 056

015

002, 015

009

030

015, 030, 069

008

008, 009, 015, 021

067

005, 013, 019, 048, 049

007, 009

007

Vector Research

Victor

Video Concepts

Videosonic

Wards

014, 016

016

014, 016

007

005, 006, 007, 008, 009,

012, 013, 015, 027, 031, 035

Yamaha

Zenith

002, 014, 016, 030, 046

011, 017, 026, 079

Setting Up Your Remote Control to Operate Your Cable Box

1

Turn off your cable box.

continued...

4.2

C HAPTER F OUR : S PECIAL F EATURES

6

9

5

,

6

7

6

6

9

9

1

7

7

9

8

9

0

5

5

8

6

5

5

5

8

,

2

8

7

6

9

,

00583F(E)-CHAPTER 4 7/19/05 2:34 PM Page 3

Cable Box

Codes

S P E C I A L F E AT U R E S

2

Press the MODE button and make sure that the CABLE LED is illuminated.

The remote control has four

“modes”: “TV,” “VCR,” “CABLE” and “DVD.”

Press the “MODE” button to switch the remote control to the “Cable” mode.

3

On your Samsung remote control, press SET.

4

Enter 3 digits of the cable box code listed below for your brand of cable box.

Make sure you enter 3 digits of the code, even if the first digit is a

“0.” (If more than one code listed, try the first one.)

5

Press POWER. Your cable box should turn on. If your cable box turns on, your remote control is now “set up” correctly.

6

Once your remote control is set up, press the MODE button any time you want to use the remote to operate your cable box.

If your cable box does not turn on, repeat steps 2, 3, and 4, but try one of the other codes listed for your particular brand of cable box. (If no other codes are listed, try each cable box code, 000 through 077.)

When your remote control is in the “CABLE” mode, the volume buttons still control your TV’s volume. Also, the VCR control buttons

(PLAY, PAUSE, etc.) will still operate your VCR.

C HAPTER F OUR : S PECIAL F EATURES

4.3

00583F(E)-CHAPTER 4 7/19/05 2:34 PM Page 4

S P E C I A L F E AT U R E S

Setting the On/Off Timer

1

Press MENU to display the menu.

Press CH ▼ twice to highlight the “SET UP” sub-menu.

Before using the timer, you must set the TV’s clock. (See “Setting the

Clock” on page 3.8)

When any of the timers are set, the

“Timer” LED will illuminate (front panel of TV).

2

Press VOL + to select the “SET UP” sub-menu.

Press CH

▼ twice to highlight "Time."

Press VOL +

3

Press CH

▼ to select

“On time.”

Press VOL + to highlight the “On time” hours.

(The hours digits will start blinking.)

Press CH

▲ or CH ▼ repeatedly to select the appropriate hours (i.e., the hour when the TV will turn on.)

4

Press VOL + to highlight the “On time” minutes.

(The minutes digits will start blinking.)

Press CH

▲ or CH ▼ )to select the appropriate minutes.

When you set the hours, make sure the correct time of day (AM or

PM) appears to the left of the hour.

continued...

4.4

C HAPTER F OUR : S PECIAL F EATURES

00583F(E)-CHAPTER 4 7/19/05 2:34 PM Page 5

S P E C I A L F E AT U R E S

5

Press VOL + to highlight “On/Off.”

Press CH

▲ (or CH ▼) to turn the on-timer

“On.” (Repeatedly pressing CH ▲ or

CH

▼ will alternate between on and off.)

6

When finished, press

VOL +.

7

To set the Off time, press

CH

▼ to highlight “Off time.”

Press VOL + and set the hours and minutes.

(Follow the same procedure as in steps 1~6 above.)

8

When finished setting the timer, press MENU three times to exit.

To deactivate the “On time,” select “Off” during this step.

Setting the Sleep Timer

The sleep timer automatically shuts off the TV after a preset time

(from 10 to 360 minutes).

1

Press the SLEEP button on the remote control.

After about 5 seconds, the sleep display will disappear from the screen, and the time interval will be set.

2

Press SLEEP repeatedly until the appropriate time interval appears (any of the preset values from “Off” to “360”).

C HAPTER F OUR : S PECIAL F EATURES

4.5

00583F(E)-CHAPTER 4 7/19/05 2:34 PM Page 6

S P E C I A L F E AT U R E S

Viewing Closed Captions

Your TV decodes and displays the closed captions that are broadcast with certain TV shows.

These captions are usually subtitles for the hearing impaired or foreign-language translations. All VCRs record the closed caption signal from television programs, so home-recorded video tapes also provide closed captions. Most pre-recorded commercial video tapes provide closed captions as well. Check for the closed caption symbol in your television schedule and

Note: The Caption feature does not work with DVD or DTV signals.

The DTV mode is not available on model PCJ533RF.

1

Press MENU to display the menu.

Press CH ▼ two times to select the “SET UP” menu.

Quick way to access captions menu: Simply press the Caption button on the remote control:

Press VOL+.

2

Press CH

▼ five times to select the “Caption” menu.

Press VOL+ to open the

Caption menu.

3

Press VOL+ or VOL – to turn closed captioning on/off.

Misspellings and unusual characters sometimes occur during closed caption transmissions, especially those of live events. There may be a small delay before captions appear when you change channels. These are not malfunctions of the TV.

4

Press CH

▼ to highlight “Mode.”

Press VOL – or VOL + to select

“Caption” or “Text.”

5

Depending on the particular broadcast, it might be necessary to make changes to “Channels” and “Field”:

Use the CH

, CH , VOL + and VOL - buttons to make the changes. (Follow the same procedure as in steps 3~4 above.)

Press MENU three times to exit.

4.6

C HAPTER F OUR : S PECIAL F EATURES

In caption mode, captions appear at the bottom of the screen, and they usually cover only a small portion of the picture.

In text mode, information unrelated to the program, such as news or weather, is displayed. Text often covers a large portion of the screen.

Different channels and fields display different information: Field 2 carries additional information that supplements the information in

Field 1. (For example, Channel 1 may have subtitles in English, while

Channel 2 has subtitles in Spanish.)

d ala e

00583F(E)-CHAPTER 4 7/19/05 2:34 PM Page 7

S P E C I A L F E AT U R E S

Fine Tuning Channels

Use fine tuning to manually adjust a particular channel for optimal reception.

1

Select the appropriate channel.

2

Press MENU.

Press CH

▼ two times to highlight “SET UP.”

3

Press VOL + to select

Setup menu. (Channel set up” will be highlighted.)

Press VOL + so that “Auto program” is highlighted.

Press CH

▼ once to select “Fine tune.”

4

Press the VOL – and VOL + buttons to adjust the fine tuning.

5

To store the fine tuning setting in the TV’s memory, press CH

▲. (A yellow-heart icon will appear.)

To reset the fine tuning to “00,”press CH

▼ .

After you adjust the fine tuning, the letters “MFT” will appear when you press DISPLAY while watching this channel.

Press the MENU button to resume normal viewing.

2

C HAPTER F OUR : S PECIAL F EATURES

4.7

00583F(E)-CHAPTER 4 7/19/05 2:34 PM Page 8

S P E C I A L F E AT U R E S

LNA (Low Noise Amplifier)

If the TV is operating in a weak-signal area, sometimes the LNA function can improve the reception (a low-noise preamplifier boosts the incoming signal).

1

Press MENU to display the menu.

Press CH

▼ two times to highlight the “SET UP” menu.

Press VOL + to select the

Set up menu. “Channel set up” will be highlighted.

2

Press VOL + to select

“Channel set up.”

Press CH

▼ twice to highlight “LNA.”

3

Press VOL - or VOL + to select LNA “on.”

Press MENU three times to exit.

Pressing VOL - or VOL + will alternate between “On” and “Off.”

4.8

C HAPTER F OUR : S PECIAL F EATURES

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 9

S P E C I A L F E AT U R E S

Special Audio Options:

Dolby Surround, MTS, and Headphones

Depending on the particular type of audio that is being broadcast, you can listen to any of three modes: Mono, Stereo and SAP (Secondary Audio Programming, which is typically a foreign-language translation).

The Dolby Surround options (3D-Phonic and Dolby Prologic) simulate the ambience of a stadium or a movie theater. The wireless headphone option is especially useful when simultaneously watching the main screen and the PIP window.

Dolby Prologic

Your Samsung TV can create a “surround” effect such that the sound seems to come from all directions.

1

Press MENU, then press the CH

▼ button three times. The DOLBY

SURROUND icon will be highlighted (starts blinking).

Press VOL + as often as necessary to select the appropriate surround system (“Off”,

“Prologic,” or “3D Phonic”).

2

If Dolby Prologic is selected, follow the instructions below. For

“3D Phonic,” see next page.

Select the mode: Press the CH ▼ button to highlight “Mode.” Next, press VOL+ repeatedly until the appropriate mode appears (“Wide,” “Phantom,” or “Normal”).

Some recommended settings:

Phantom : Selected when the center speaker is either not present or not used.

In Phantom Mode, the center sound is output through both left and right speakers.

Normal : Selected when the center speaker is smaller than the main TV speakers. In Normal

Mode, the sound of the center channel is output through both left and right speakers.

Wide : Selected when the center speaker is larger than the TV speaker. In Wide Mode, the sound of center channel is output through only the center speaker.

After selecting the mode, press the CH

▼ button, and highlight “Center.” Next, press VOL+ or

VOL- and, depending on personal preference, select any value between -10 and +10. Follow a similar procedure for “Rear” and “Delay.” (Some trial-and-error experimenting is necessary to find the optimal setting, which will vary according to individual preference).

After entering values for “Center,” “Rear,” and “Delay,” use the CH ▼ and VOL+ buttons to activate

“Test.” During “Test,” a tone will cycle through the speakers so you can hear the surround effect and make additional changes as needed.

Press MENU twice to exit.

C HAPTER F OUR : S PECIAL F EATURES

4.9

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 10

S P E C I A L F E AT U R E S

Dolby 3D Phonic

3

Follow steps one and two

(previous page). Select

3D Phonic. Then press

VOL + to select one of these three modes:

“Drama,”

“Action,” or

“Theater”.

Quick way to access the 3D-Phonic menu: Just press “3D-PHONIC” on the remote control:

Next, press the CH

▼ button so that “Effect” is highlighted (the letters turn blue). Repeatedly press either VOL+ or VOL- to set the effect. (The actual setting depends on personal preference:

Select any value between -5 and +5.)

4

Press MENU twice to exit.

Manufactured under license from Dolby Laboratories Licensing

Corporation.

DOLBY, the double-D symbol and “PRO LOGIC” are trademarks of Dolby Laboratories Licensing Corporation.

Notes

In order to enjoy the Dolby sound in the Dolby Pro Logic

Mode, connect the TV to the external center and surround speakers. The external speakers are not provided. They must be purchased separately.

The Dolby surround properly functions only when software such as Video tape having the double-D symbol “ ” is played.

When viewing software not recorded using Dolby sound or an ordinary TV program set the Dolby mode to “Off”.

4.10

C HAPTER F OUR : S PECIAL F EATURES

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 11

S P E C I A L F E AT U R E S

Choosing a Multi-Channel Sound (MTS) Soundtrack

Depending on the particular program being broadcast, you can listen to stereo, mono, or a Separate Audio Program. (SAP audio is usually a foreign-language translation.

Sometimes SAP has unrelated information like news or weather.)

1

Press MENU to display the menu.

Quick way to access the MTS menu: Just press “MTS” on the remote control:

Press CH

▼ once to highlight the AUDIO menu.

2

Press VOL + to select the AUDIO menu.

Press CH

▼ to highlight “MTS”.

3

Press VOL + repeatedly to select “Mono,”

“SAP,” or “Stereo.”

Press MENU twice to exit

The text at the bottom of the menu tells you if the incoming audio is stereo, SAP, or mono.

• Choose Stereo for channels that are broadcasting in stereo.

• Choose Mono for channels that are broadcasting in mono, or if you are having difficulty receiving a stereo signal.

• Choose SAP to listen to the Separate Audio Program, which is usually a foreign-language translation.

You can also change the MTS setting by pressing the “MTS” button on the remote control. (When you change channels, MTS is set to “Stereo” automatically.

To listen in ‘SAP’ or ‘Mono,’ change the MTS setting.)

C HAPTER F OUR : S PECIAL F EATURES

4.11

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 12

S P E C I A L F E AT U R E S

Using Wireless Headphones

1

Connect the transmitter cable to the Wireless

Headphone jack on the bottom of the back panel.

2

Turn the transmitter and

Wireless Headphones on.

3

Adjust the volume of the

Wireless Headphones.

Note: Wireless headphones must be purchased separately.

Setting up Wireless Headphones with Picture-in-Picture

(See page 4.13 for information about the various options for picture-in-picture.)

1

Press MENU and press

CH

▼ once to highlight the AUDIO icon.

Press VOL+, then press

CH

▼ to highlight

“Headphone.”

Note: The “Headphone” option is active only when the PIP window is active.

2

Press VOL+ to alternate between “Main” and

“Sub” (the sound associated with program in PIP window). If PIP is not active, then the “Sub” option is not available.

Press MENU twice to exit.

4.12

C HAPTER F OUR : S PECIAL F EATURES

Notes: If there is an obstacle between the transmitter and the

Wireless Headphones, the sound may be affected. For additional details, see your Wireless

Headphones instruction book.

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 13

S P E C I A L F E AT U R E S

Viewing Picture-in-Picture

You can use the PIP feature to simultaneously to watch two video sources.

Note: The PIP feature does not work with DVD or DTV signals.

The DTV mode is not available on model PCJ533RF.

Activating Picture-in-Picture

1

Press MENU to display the menu.

Press CH

▼ four times to highlight the PIP menu.

Quick way to access the PIP menu: Simply press the PIP button on the remote control:

Press VOL + to select the

PIP menu.

2

Press VOL + to select

PIP “On.”

If you turn TV off while watching and turn it on again, the PIP window will disappear.

3

Press MENU twice to exit.

Note: Picture-in-Picture does not function when the V-chip is active.

C HAPTER F OUR : S PECIAL F EATURES

4.13

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 14

S P E C I A L F E AT U R E S

Selecting a Signal Source (Antenna or Cable) for PIP

1

Press MENU to display the menu.

Press CH ▼ four times to select the PIP menu.

Press VOL + to select the PIP menu.

2

Press CH

▼ four times to select “ANT/CATV.”

If an antenna is connected, the setting is “ANT.”

If a Cable TV system is providing the signal, press VOL + or VOL - until the appropriate type of cable system is is displayed (“STD,” “HRC,” or

“IRC”).

Press MENU twice to exit.

Selecting a Signal Source (External A/V) for PIP

Press TV/VIDEO repeatedly to cycle through all of the available signal sources:

“TV,” “Video 1,” “Video 2,” “Video 3,” “S-Video 1,”and

“S-Video 2.”

For more information about external A/V components and signals, see “Viewing a VCR or

Camcorder Tape” on page 3.14.

If you select “TV”, the PIP image is the same as the main image.

Swapping the Contents of the PIP image and Main image

When you press the SWAP button:

The image in the PIP window will appear on the main screen, and vice versa.

4.14

C HAPTER F OUR : S PECIAL F EATURES

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 15

S P E C I A L F E AT U R E S

Changing the PIP Channel

Press PIP CH

▲ or CH▼ to change the channel that appears in the PIP window

Changing the Location (Rotating) the PIP Window

When you press the ROTATE button repeatedly, the PIP window moves from corner to corner on the TV screen.

Freezing the PIP Image

Press STILL to stop the action in a particular scene. Press

STILL again to resume normal video.

Changing the Size of the PIP Window

Press P.SIZE to alternate between a smaller and larger PIP window.

Scanning the Available Channels

This procedure scans all of the available channels and then stores them in memory.

Press CH.SCAN, and the memorized channels will appear in sequence for 2 to 3 seconds per channel.

Press CH.SCAN again to stop the scanning process.

When CH.SCAN stops, the viewing mode will return to its original setting.

C HAPTER F OUR : S PECIAL F EATURES

4.15

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 16

S

P E C I A L

F

E AT U R E S

Using the V-Chip

The V-Chip feature automatically locks out programming that is deemed inappropriate for children. The user must first enter a PIN (personal ID number) before any of the V-Chip restrictions can be set up or changed.

Note : When the V-chip feature is active, the PIP and channel-auto program features do not function.

Setting Up Your Personal ID Number (PIN)

1

Press MENU to display the menu.

Press CH

▼ two times to select the “SET UP” menu.

Quick way to access the V-Chip menu: Simply press the V.CHIP

button on the remote control:

Press VOL + .

2

Press CH ▼ six times to select the “V-chip” menu.

Press VOL+.

The “Enter pin” screen will appear. Enter your 4-digit PIN number. Note: The default PIN number for a new TV set is

0-0-0-0.”

3

After entering a valid PIN number, the “V-chip mode” screen will appear. Press

CH ▼ three times and highlight “Change pin.”

(Note: When a particular field is highlighted, its color turns BLUE.)

4

While the “Change pin” field is selected, press

VOL +. The Change pin screen will appear.

Choose any 4-digits for your PIN and enter them.

Note: If you forget the PIN, press the remote-control keys in the following sequence, which resets the pin to 0-0-0-0:

POWER OFF

➜ MUTE ➜ 8 ➜ 2 ➜

4 ➜ POWER ON.

As soon as the 4 digits are entered, the “Confirm pin” screen appears. Re-enter the same 4 digits. When the Confirm screen disappears, your PIN has been memorized.

Press MENU to exit.

4.16

C HAPTER F OUR : S PECIAL F EATURES

t

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 17

S P E C I A L F E AT U R E S

How to Enable/Disable the V-Chip

1

Press MENU.

Press CH ▼ two times to select the “SET UP” menu.

Press VOL + .

2

Press CH

▼ six times to highlight the “V-chip” menu.

Press VOL+ .

The “Enter pin” screen will appear. Enter your

4-digit PIN number.

3

The “V-Chip mode” screen will appear, and “V-Chip lock” will be highlighted (turns blue color).

To enable the V-Chip feature, press VOL + so that the “V-

Chip lock” field is YES.

(Pressing VOL + will alternate between YES and NO.)

How to Set up Restrictions Using the “TV guidelines”

First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.) Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating.

1

Press MENU to display the menu.

Press CH

▼ two times to highlight the “SET UP” menu.

Press VOL + .

C HAPTER F OUR : S PECIAL F EATURES

4.17

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 18

S P E C I A L F E AT U R E S

2

Press CH ▼ six times to highlight the “Vchip” menu.

Press VOL+ .

The “Enter pin” screen will appear. Enter your 4-digit PIN number.

3

The “V-chip mode” screen will appear. Press the

CH

▼ button, and highlight the field for “TV

Guidelines.” (Note: When a particular field is highlighted, its color turns BLUE.)

4

Press VOL +. The “TV guidelines” screen will appear. Press the CH

▲,

CH

▼ buttons to highlight one of the six age-based categories:

TV-Y

TV-Y7

Young children

Children 7 and over

--------------------------------------

TV-G

TV-PG

General audience

Parental guidance

TV-14

TV-MA

Viewers 14 and over

Mature audience

Note: These categories consist of two separate groups: TV-Y and TV-Y7

(young children through age 7), and

TV-G through TV-MA (everybody else). The TV-Y and TV-Y7 categories are colored green.

The restrictions for these two groups work independently: If a household includes very young children as well as young adults, the TV guidelines must be set up separately for each age group. (See next step.)

5

At this point, one of the TV-Ratings is highlighted (blue color).

Press the VOL + button: Depending on your existing setup, a letter “U” or “B” will start blinking.

(U= Unblocked, B= Blocked)

While the “U” or ”B” is blinking, press the CH ▲ or CH ▼ button to block or unblock the category.

Press MENU once to save the TV guidelines. A TV-Rating will be highlighted (BLUE), and no letters will blink. To exit this screen, press MENU again. To select a different TV-Rating, press CH ▲ or CH ▼ and then repeat the process.

Note 1: The TV-Y7, TV-PG, TV-14 and TV-MA have additional options. See the next step to change any of the following sub-ratings:

FV: Fantasy violence

D: Dialog

L: L

S: Sexual situation

V: Violence

Note 2: The V-Chip will automatically block certain categories that are “more restrictive.” For example, if you block

“TV-Y” category, then TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the categories in the “young adult” group will be blocked (TV-G, TV-PG, TV-14 and TV-MA). The sub-ratings (D, L, S, V) work together similarly. (See next section.)

4.18

C HAPTER F OUR : S PECIAL F EATURES

ps d ll ge of

Y7 d es

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 19

S P E C I A L F E AT U R E S

6

How to set the FV, D, L, S and V sub-ratings.

First, highlight one of these TV-Ratings: TV-Y7, TV-PG, TV-14 or TV-MA (See Step 4, on previous page).

Next, while the TV-Rating is highlighted (BLUE), repeatedly press the VOL + button. This will cycle through the available sub-ratings (FV,L, S, D or V).

A blinking letter (“U” or “B”) will be displayed for each sub-rating. While the “U” or “B” is blinking, press

CH ▲ or CH ▼ to change the sub-rating.

Press MENU once to save the TV guidelines. A TV-Rating will be highlighted (BLUE), and no letters will blink.

To exit this screen, press MENU again. To select a different TV-Rating, press CH

▲ or CH ▼ and then repeat the process.

Note: The V-chip will automatically block certain categories that are “More restrictive”. For example, if you block “L” sub-rating in TV-PG, then the “L” sub-ratings in TV-14 and TV-MA will automatically be blocked.

7

Press the MENU button three times to clear all the screens. (Or proceed to the next section, and set up additional restrictions based on the MPAA codes).

How to Set up Restrictions using the MPAA Ratings: G, PG, PG-

13, R, NC-17, X

The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main application is for movies. (Eventually, movie videocassettes will be encoded with MPAA ratings.) When the V-Chip lock is on, the TV will automatically block any programs that are coded with objectionable ratings (either MPAA or TV-Ratings).

1

Press MENU to display the menu.

Press CH

▼ two times to highlight the “SET UP” menu.

Press VOL + .

2

Press CH

▼ six times to highlight the “V-chip” menu.

Press VOL+ .

The “Enter pin” screen will appear.

Enter your 4-digit PIN number.

C HAPTER F OUR : S PECIAL F EATURES

4.19

00583F(E)-CHAPTER 4 7/19/05 2:35 PM Page 20

S P E C I A L F E AT U R E S

3

The “V-chip mode” screen will appear.

Press the CH ▼ button twice, and highlight

“MPAA rating.”

4

While “MPAA rating” is highlighted, press the VOL + button. The “MPAA rating” screen will appear.

5

Repeatedly press the CH

▼ button to highlight a particular MPAA category.

(When a category is highlighted, its color changes to blue.) Pressing the CH

▼ button will cycle through the

MPAA categories:

G

PG

General audience (no restrictions).

Parental guidance suggested.

PG-13 PG-13 (Parents strongly cautioned).

R R (Restricted. Children under 17 should be accompanied by an adult).

NC-17 No children under age 17.

X X (Adults only).

NR Not rated.

While a particular category is highlighted, press VOL + to activate it.

A blinking letter (“U” or “B”) will be displayed. Press CH

▲ or CH ▼ to select “U” or”B”.

Press MENU three times to save the settings and to clear all screens.

Note: The V-Chip will automatically block any category that is “more restrictive.” For example, if you block the “PG-13” category, then “R,” “NC-17,” and “X” will automatically be blocked also.

How to Reset the TV after the V-Chip

Blocks a Channel (“Emergency Escape”)

If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the following message will appear: “Excessive rating.”

To resume normal viewing, tune to a different channel using the number buttons. Under certain conditions

(depending on the rating of the local TV programs) the V-Chip might lock out all the channels. In this case, use the V-Chip button for an “emergency escape”:

Press the V-chip button on the remote control. Enter your PIN number, and press VOL + to temporarily disable the V-Chip Lock.

4.20

C HAPTER F OUR : S PECIAL F EATURES

00583F(E)-CHAPTER 5 7/19/05 2:36 PM Page 1

C h a p t e r F i v e

T R O U B L E S H O O T I N G

If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting tips apply, then call your nearest service center.

Identifying Problems

Problem

Poor picture

Poor sound quality.

No picture or sound.

No color, wrong colors or tints.

Picture rolls vertically.

The TV operates eratically

Your remote control does not operate your TV.

The TV won’t turn on.

Possible Solution

Try another channel.

Adjust the antenna.

Check all wire connections.

Try another channel.

Adjust the antenna.

Try another channel.

Press the TV/VIDEO button.

Make sure the TV is plugged in.

Check the antenna connections.

Make sure the program is broadcast in color.

Adjust the picture settings.

Adjust the antenna.

Check all wire connections.

Unplug the TV for 30 seconds, then try operating it again.

Press the “MODE” button to put your remote control in the “TV” mode.

Make sure the wall outlet is working.

Note: If you watch a still image or the screen in the 16:9 aspect ratio format for a long time, some burning images may be seen on the screen.

C HAPTER F IVE : T ROUBLESHOOTING

5.1

00583F(E)-APPENDIX 7/19/05 2:28 PM Page 1

A.1

A PPENDIX

A P P E N D I X

Cleaning and Maintaining Your TV

With proper care, your TV unit will give you many years of service. Please follow these guidelines to get the maximum performance from your TV.

Placement

• Do not place the TV near extremely hot, cold, humid or dusty places.

• Do not place the TV near appliances with electric motors that create magnetic fields, such as vacuum cleaners.

• Keep the ventilation openings clear; do not place the TV on a soft surface, such as cloth or paper.

• Place the TV in a vertical position only.

Liquids

• Do not handle liquids near or on the TV. Liquids that spill into it can cause serious damage.

Cabinet

• Never open the cabinet or touch the parts inside.

• Wipe your TV with a clean, dry cloth. Never use water, cleaning fluids, wax, or chemicals.

• Do not put heavy objects on top of the cabinet.

Temperature

• If your TV is suddenly moved from a cold to a warm place, unplug the power cord, and allow at least two hours for moisture that may have formed inside the unit to dry completely.

Using Your TV in Another Country

If you plan to take your TV with you to a foreign country, please be aware of the different television systems that are in use around the world. A TV designed for one system may not work properly with another system due to differences in the TV channel frequencies

Specifications

Model

Voltage

Frequency of Operation

Power Consumption

Dimension

Weight

PCJ532RF / PCJ533RF / PCJ534RF / PCJ611RF / PCJ614RF / PCK5315R / PCK6115R

AC 120V

60Hz

285 Watts

PCJ532RF / PCJ533RF : 1167 x 615 x 1418mm ; 45.94 x 24.21 x 55.83 inches

PCJ534RF / PCK5315R : 1167 x 615 x 1418mm ; 45.94 x 24.21 x 55.83 inches

PCJ611RF / PCJ614RF/PCK6115R:

1131 x 694 x 1524mm ; 44.53 x 27.32 x 60.00 inches

PCJ532RF / PCJ533RF / PCJ534RF / PCK5315R: 78 Kg;171.96 lbs

PCJ611RF / PCJ614RF / PCK6115R : 132 Kg;291.01 lbs

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents