advertisement
Rear Projection Display
Installation Manual
REQUEST A SALES DEALER FOR INSTALLATION
Please read all instructions below and install this system properly.
Please read "SAFETY PRECAUTIONS" and "IMPORTANT SAFETY INSTRUCTIONS" on
OWNER'S MANUAL to install and place this system.
This system is supplied in 3 packages and they need to be installed. Please make sure all the parts are included. If any part is missing, or if you have questions, contact a sales dealer.
Install the system following steps.
1.
CHECK CONTENTS IN PACKAGES
2.
ASSEMBLE BOTTOM CABINET
3.
JOINT TOP AND BOTTOM CABINETS
4.
SETUP PROJECTION MIRROR
5.
ADJUST PROJECTION MIRROR
6.
ASSEMBLE STORAGE SPACES
7.
LOCK CABINET
THIS SYSTEM MUST BE INSTALLED BY 2 OR MORE PEOPLE
CAUTION
WHEN INSTALLING THIS SYSTEM, BE CAREFUL NOT TO DAMAGE THE PROJECTION
SCREEN. AND NEVER TOUCH THE SURFACE OF THE PROJECTION SCREEN AND
THE PROJECTION MIRROR DIRECTLY. THEY MAY EFFECT THE PROJECTION IMAGE
QUALITY.
BE CAREFUL NOT TO DROP ANY PART OR TOOL LIKE SCREW INTO THE SYSTEM. IF
IT SHOULD, CONTACT A SERVICE.
EXCEPT WHEN ADJUSTING THE PROJECTION MIRROR, NEVER TURN THE SYSTEM
ON UNTIL THE INSTALLATION IS FINISHED. IT MAY CAUSE ELECTRICAL SHOCK OR
FIRE HAZARD.
710-00792-1 1AA6P1P1756-- (M8EA)
1
CHECK CONTENTS IN PACKAGES
This system is supplied in 3 packages. Make sure all the parts listed below (cabinets, Installation parts, and accessories) are included in those packages.
Package 1
Top Cabinet : Refer to the steps 3 to 6 for installation.
Package 2
Package 3
Bottom Cabinet : Refer to the steps 2, 6 and 7 for installation.
Installation Parts
Qty.
Glass Doors ------------------------------------------- 2
Compartment Shelves ----------------------------- 4
Shelves' Pins ----------------------------------------- 16
Installation Part
Accessories
Qty.
Center Panel ----------------------------------------- 1
Owner's Manual --------------------------------------- 1
Installation Manual (this brochure) --------------*
AC Power Cord --------------------------------------*
Wireless Remote Control Unit -------------------- 1
Wireless/Wired Remote Control Unit ----------- 1
Remote Control Cable ----------------------------- 1
Batteries for Remote Controls -------------------- 4
VGA Cable ------------------------------------------- 1
MAC/VGA Adapter ---------------------------------- 1
Mouse Cables (Serial, PS/2, ADB)--------------*
The accessories marked ( * ) may not supplied or may be differ in quantity in some models. Refer to the Owner's
Manual for details.
Package 1
Package 3
Package 2 u Actual packages may be differ from this figure in some models.
2
ASSEMBLE BOTTOM CABINET
1
Remove Joint Bolts and Cover Plates
Remove the 4 Joint Bolts on the Bottom Cabinet.
Keep these bolts for later use. They are necessary for joint the Top and Bottom Cabinets.
Remove the 2 Cover Plates on the top of the
Bottom Cabinet. Keep the Cover Plates for later use. Replace those plates, when the appliance needs to be transported.
Cover Plates
(2 pcs)
Joint Bolts
(4 pcs)
2
Install Center Panel
Install the Center Panel to the Bottom Cabinet. Be sure to meet the Center Panel and the Bottom
Cabinet at the upper part first, and insert the 6 legs of Center Panel to the holes of the Bottom Cabinet.
Be sure to set the Center Panel securely.
Joint Bolts (4 pcs)
Hole Leg
Center Panel
Meet the Center Panel and the Bottom
Cabinet at the upper part first and push in the Panel securely.
3
Remove Protection Pads
There are the 5 Protection Pads inside of the
Bottom Cabinet for protection against shock or vibration. Remove the 4 Pads supporting at the upper side of the Bottom Cabinet first. And then, remove the pad(A) supporting at the lower side of the projector. When removing the pad(A), pull downward first and remove the pad.
CAUTION
WHEN REMOVING THE PROTECTION
PADS, BE CAREFUL NOT TO BROKE THE
WIRING INSIDE OF THE BOTTOM
CABINET.
BE SURE TO REMOVE ALL THE
PROTECTION PADS INSIDE OF THE
CABINET. AND BE CAREFUL NOT TO
LEAVE ANY PAD OR FRAGMENT IN THE
CABINET. IT MAY RESULT IN FIRE
HAZARDS.
Protection Pads (5 pcs)
The back side of the Bottom Cabinet.
Pad(A)
Pull the pad(A) to downward first and remove the pad.
Projector
3
J0INT TOP AND BOTTOM CABINETS
1
Joint Top and Bottom Cabinets
Lift the Top Cabinet and put it on the Bottom
Cabinet. When setting the Top Cabinet, be sure the frame of the Bottom Cabinet is fitted into the frame of the Top Cabinet completely.
CAUTION
THE TOP CABINET OF THIS PROJECTOR
HAS ITS GRAVITY AT THE SCREEN SIDE.
WHEN LIFTING THE TOP CABINET, BE
CAREFUL NOT TO DROP.
2
Remove Back Cover
Remove the 14 Screws and the Back Cover. Keep the screws and Back Cover. All the installations are finished, all those parts should be replaced.
Screws (14 pcs)
3
Remove Cover Plate
Remove the Cover Plate on the lower part of the
Top Cabinet. Keep the Cover Plate for later use.
Replace this plate when the appliance need to be transported.
Top
Cabinet
Bottom
Cabinet
Top
Cabinet
,,,
Frame
,,,
,,,
Bottom
Cabinet
Be sure the frame of the Bottom Cabinet is fitted into the frame of the Top
Cabinet completely.
4
Fix the Cabinets
Joint the Top and the Bottom Cabinets with the 4
Joint Bolts securely.
CAUTION
BE SURE TO FIX THE CABINETS WITH
JOINT BOLTS. IF THE TOP AND THE
BOTTOM CABINETS ARE NOT FIXED
PROPERLY, THE TOP CABINET MAY
BE DROPPED OR FALL DOWN.
Joint Bolts
(4 pcs)
Cover Plate
Joint Bolts
(4 pcs)
4
SETUP PROJECTION MIRROR
1
Preparation
Remove the 4 Protection Pads inside of the Top
Cabinet and remove the 2 Fixing Bands (right and left) of the Projection Mirror.
CAUTION
NEVER TOUCH THE PROJECTION
MIRROR DIRECTLY. IT MAY EFFECT THE
PROJECTION IMAGE QUALITY. MOVE
THE MIRROR BY HOLDING THE MIRROR
HANDLE.
BE SURE TO REMOVE ALL THE
PROTECTION PADS FROM THE CABINET.
2
Set Mirror Arms
Remove the 8 Screws(A) of the Mirror Arms. Lift the Projection Mirror and raise the Mirror Arms backward.
Loosen the Screws(B) on the end of the Mirror
Arms. Put the Mirror Holder between the Adjusting
Nut and the Washer at each side of the Mirror. And then fix the Mirror Holders on the Mirror Arms with the Screws(B) temporary.
3
Fix Projection Mirror
Fix the Mirror Arms on the Cabinet with the
Screws(A). Fix the Projection Mirror to the end of the Mirror Arms with the Screws(B) securely.
Projection Mirror
Fixing Bands
Protection Pads (4pcs)
Projection Mirror
Mirror Handle
Fixing
Bands
(2 pcs)
Screws(A)
(4 pcs X 2)
Mirror Arm
Screw(B)
Mirror Arm
Screws(A)
(4 pcs X 2)
Adjusting Nut Screw(B)
Mirror Holder
Mirror Arm
Washer
5
ADJUST PROJECTION MIRROR
When the figure of the projection image does not match the Projection Screen, adjust the Projection
Mirror. If the figure fits the Projection Screen precisely, skip the steps 2, 3 and 4 and replace the Back
Cover.
1
Check Projection Image
Connect the projector to the AC outlet, and turn the projector on. Connect the video output equipment to the projector. Project the image of cross-hatch or circles to check whether the picutre is displayed fully on the Projection Screen and is not distorted.
(Refer to the Owner's Manual for operation.)
If the figure is distorted, adjust the Projection Mirror following the steps 2 to 4 below.
If the picture is displayed properly, adjustment of the Mirror is not required. Skip the steps below and replace the back cover.
Mirror Holder
Screw(B)
2
Adjust Projection Mirror
Adjust the Projection Mirror by turning the Adjusting
Nuts. Move the Projection Mirror up or down by turning the Adjusting Nuts on the both sides of the
Projection Mirror. Adjust Screw(B) if it required.
Refer to the figure on the right for the image movement with the Adjusting Nut.
Lower the
Mirror Holder.
Mirror Arm
Lift the Mirror
Holder.
Adjusting Nut
3
Fix Projection Mirror
Fix the Projection Mirror where the picture is displayed properly. Fix the Screw(B) securely.
When fixing the Screw(B) the figure may be distorted again. When it should happen, readjust the Mirror following the steps 2 to 4.
Turn Adjusting Nuts to adjust the screen image.
When turning the
Adjusting Nuts on both sides to the right, the lower part of the image becomes narrow.
4
Turn the projector off
Turn off the projector and disconnect it from the AC outlet.
CAUTION
DO NOT STARE DIRECTLY INTO THE
LENS. EYE DAMAGE COULD RESULT.
WHEN ADJUSTING THE MIRROR, NEVER
TOUCH THE PARTS EXCEPT THE
MIRROR. IT MAY RESULT IN
ELECTRICAL SHOCK.
When turning the
Adjusting Nuts on both sides to the left, the lower part of the image is stretched.
When turning the
Adjusting Nuts on one side to the left or the right, one side of the lower part of the figure is shortened or stretched.
6
ASSEMBLE STORAGE SPACES
Screws (14 pcs)
1
Replace Back Cover
Replace the Back Cover to the Top Cabinet. Turn the Back Cover over, and fix the cover in the reverse to the initial position.
Back Cover
2
Install Glass Doors
1. Remove the Hinge Covers by removing the 2 screws of each Hinge.
2. Hold the Glass Doors between the Glass Hinges and the Hinge Covers. Install the Glass Doors so that the side with the Holder Magnet is matched to the magnet inside of the Storage Spaces. Do not install the Glass Doors in the reverse.
Tighten the screws and fix the Glass Doors.
3
Adjustments of Doors
1. When adjusting the position of the Glass Doors, loose the Screws(A) and move the Glass Doors with the Hinges to the arrow direction until the surface of the door matches to the surface of the
Cabinet Front.
2. When adjusting the tilt of the Glass Doors, adjust the Screws(B) (lower and upper) and move the
Glass Doors.
Screws
(2pcs x 4)
Screw(A)
Holder Cover
Glass Door
Screw(B)
Holder Magnet
Shelves' Pins
(4 pcs X 4)
4
Install Compartment Shelves
IInsert the Shelves' Pins into appropreate position of the walls of Storage Spaces. Install the
Compartment Shelves in Storage Spaces.
Compartment
Shelves (4 pcs)
7
LOCK CABINET
1
Lock the Cabinet
Turn Lock Bolts to the direction indicated on the figure to lock the cabinet on the floor. Make sure that all the Casters are slightly raised from the floor.
The tilt of Cabinet can be also adjusted with these
Lock Bolts.
CAUTION
BE SURE TO LOCK THE CABINET WITH
LOCK BOLTS PROPERLY. IF THE
CABINET IS NOT LOCKED, CABINET IS
UNSTABLE AND MAY FALL DOWN.
Lock Bolt
Lifting the cabinet up to settle it.
Letting the cabinet down to move it.
Cabinet Dimensions ( W x H x D ) : 1532 mm (60.3") x 1968mm (77.5" ) x 747mm (29.4" )
Net Weight : 145kg (319.7lbs )
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project