Sanyo | POA-MD13NET2 | User's Manual | Sanyo POA-MD13NET2 User's Manual

Sanyo POA-MD13NET2 User's Manual
Network Board
POA-MD13NET2
OWNER’S MANUAL
INSTALLATION and OPERATION of the Network Board
This board is the Network Board to control and set up a projector via a network. Connect
a network cable to this board, and by accessing the connected projector using the web
browser on your computer, the projector can be controlled and set up remotely.
This board is only used for our projectors that have a terminal for the Network Board.
This manual explains the installation of the Network Board and its operation.
Chapter 1 Preparation
Chapter 2 Installation
Chapter 3 Basic Setting & Operation
Chapter 4 Controlling the Projector
Chapter 5 Controlling the Multi-Projectors
Chapter 6 Use of Serial Port
Chapter 7 Appendix
Compliance
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could
be required to stop operation of the equipment.
Warning
This is a Class A product. In a domestic environment this product may cause radio
interference in which cause the user may be required to take adequate measures.
CAUTION
This product provides a lithium battery. When you discard this product, you should
return it to your local dealer.
CAUTION ON USE IN NETWORK
- When you receive an alert e-mail from the projector, you must check the projector
immediately. Fire or accident may result if the projector is used in an abnormal
condition.
- When you install the projector at remote location and use it through the network,
you must perform the safety inspections periodically. In this case you must pay
attention to the change of environment in which you installed the projector. It may
cause fire or an accident depending on the change of environment.
CAUTION
We assume no responsibility for the loss or damage of data or damage of the computer caused by use of this product.
2
Contents
Chapter 1
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Chapter 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Flow of installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
1 Name and function of each part . . . . . . . . . . . . . . . . . . . . . . . . .13
2 Installation and Network configuration . . . . . . . . . . . . . . . . . . .14
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Connection of LAN cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Network configuration (Type1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Network PIN code setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Network configuration (Type2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Password setting [Display] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Notice about system construction . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Chapter 3
Basic Setting and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Login the setting page of the projector . . . . . . . . . . . . . . . . . . . .26
1 Enter the IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
2 Select a display mode and login . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
3 Display of main setting page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
1 Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
2 Password Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
3 Date/Time Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Network Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
1 Configure the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
2 Name the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
E-mail Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
ENGLISH
1 Registering SMTP Server, Administrator Address . . . . . . . . . . . . . .32
2 Registering and deleting E-mail addresses . . . . . . . . . . . . . . . . . . .33
3 Condition selection for sending alert message . . . . . . . . . . . . . . . .33
Examples: Type and contents of alert mail . . . . . . . . . . . . . . . . . . . . .34
Chapter 4
Controlling the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Power on/off the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Check the status of projector . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Control the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
PC Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Save a Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Load a Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
System Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Network Board
OWNER’S MANUAL
3
Contents
Image Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Save a image adjustment value . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Load a image mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Screen Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Sound Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
How to set the Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Check the Timer events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Getting the current time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Cancel the timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Save Actual Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Check the Save items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Control the projector's menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Make a memo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Chapter 5
Controlling the Multi-Projectors . . . . . . . . . . . . . . . . . . . . . . .55
Multi-Control
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Register IP address and projector name . . . . . . . . . . . . . . . . . . . . . . .57
Check IP address and projector name . . . . . . . . . . . . . . . . . . . . . . . .57
Exclude/Add/Delete a projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Load and apply the setting value . . . . . . . . . . . . . . . . . . . . . . . . .59
Control multi-projectors at the same time . . . . . . . . . . . . . . . . . .60
Chapter 6
Use of Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Serial Port setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Control Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Use of Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Control the projector with Telnet
. . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Chapter 7
Appendix:A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Examples of Connection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Peer-To-Peer connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
The gateway (Router) installed in the network . . . . . . . . . . . . . . . . . .71
Web browser setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Active Script/JavaScript enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Proxy setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Examples: OS/Browsers
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Windows XP Professional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Mac OS 8.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Product specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81
Port Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Appendix:B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
4
Q&A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Preparation
1
ENGLISH
Chapter 1
Network Board
OWNER’S MANUAL
5
Chapter 1 Preparation
Features
Web Management function (☞ p.36)
With this function, you can monitor projector functions such as power status, lamp
status, input mode, signal condition, lamp-use time, etc. through the network by using
the web browser installed on your computer.
PC1
PC2
PC3
PC4
Turn on PJ1
Internet
Intranet
PJ2
PJ1
PC5
E-Mail Alert function (☞ p.32)
Projector (Network Board) sends messages to the registered e-mail addresses when
a lamp abnormality or power failure occurs with the projector. In this message, it
describes how to solve the cause of the problems. You can take efficient action for
quick recovery.
PC1
PC2
PC3
PC4
Internet
Intranet
PJ2
PJ1
PC5
You've got Mail
6
Features
Multi-control function (☞ p.56)
A single computer can control and set up the multiple computers at the same time.
PJ4
PC3
PJ3
PC4
PJ2
Internet
Intranet
PJ1
PC5
Select INPUT2
for PJ1 to PJ4
Automatic On/Off using Timer function (☞ p.47)
Automatically turn on or off the projectors at specified date/day and time by using the
clock function.
Now it's 11:30
I am ready to turn ON,
and select INPUT1 (DVI)
Control port ready for external equipment via network (☞ p.62)
This product provides a serial port (RS-232C) for controlling external equipment. By
connecting the equipment which has a serial port, it can be controlled by a computer
via the network. * This product does not provide the interface driver software to control exter-
PC1
PC2
PC3
PC4
ENGLISH
nal equipment.
Turn on the DVD player
and start playing.
Internet
Intranet
PJ2
PC5
PJ1
DVD Player
Network Board
OWNER’S MANUAL
7
Chapter 1 Preparation
Operating Environment
To perform the management and setting up the projector using this product, the environment described below is required.
Operating System
Windows 95 / Windows 98 / Windows 2000 / Windows Me / Windows NT /
Windows XP / Windows Vista (32bit version)
Mac OS 8.0 or later
Network
Network must handle Ethernet correctly and accept TCP/IP protocol.
Computer
The computer must provide a 10Base-T or 100Base-TX network card.
Web browser application*
● Microsoft Internet Explorer version 5.0 or later
● Netscape Navigator version 4.7 or later
* Use to control and set up the projector. The layout of pages in the browser
may slightly differ from each type of application or operating system you use.
Internet mail application*
● Microsoft Outlook
● Microsoft OutlookExpress
● Netscape Mail
* Required the internet e-mail application software to receive an e-mail alert
sent from this product. If you do not use the function E-mail Alert, this application is not required.
8
Operating Environment
The limitation*1 of connection between this product and Hub or
Computer
Suitable LAN cables are limited by length and type as follows;
Connection
Type of usable LAN cable
Maximum length
Network Board - Hub
UTP Straight Cable with category 3 or 5 *
100m
Network Board - Computer
UTP Cross Cable with category 3 or 5*2
100m
2
ENGLISH
*1 There may be other limitations depending on your network environment or LAN specification. Please consult your network administrator for further details.
*2 Category of LAN cable indicates the cable quality. Normally, cable with category 3 or 5 is
used for 10Base-T network and cable with category 5 is used for 100Base-TX network.
Network Board
OWNER’S MANUAL
9
Chapter 1 Preparation
Notices
Expression/Abbreviation
The following abbreviations may appear in this manual:
● Windows 95, Windows 98, Windows 2000, Windows Me,
Windows XP, Windows NT4.0, Windows Vista ➜
Windows
● Macintosh, Power Macintosh
➜
Macintosh
● Mac OS 8 or later
➜
Mac OS
The word "projector" found in this manual means "projector provided with Network
unit" unless otherwise noted.
The OS of the computer and the Web browser described in this manual is Windows
XP Professional and Internet Explorer 6.0. In case of another OS or Web browser,
some instruction procedures may differ from the actual operation depending on your
computer environment.
Use of this manual
This manual does not provide the description of basic operation and functions for
computer, web browser, projector and network. For instructions about each piece of
equipment or application software, please refer to the respective booklet.
Trademark
Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows,
Windows NT are registered trademarks of Microsoft Corporation. Macintosh, Mac
OS are registered trademarks of Apple Computer Inc. Internet Explorer is a registered
trademark of Microsoft Corporation. Netscape Navigator and Netscape Communicator
are trademarks or registered trademarks of Netscape Communications Corporation.
JavaScript is a registered trademark of Sun Microsystems, Inc.
DLP is a registered trademark of Texas Instruments. BrilliantColor and DynamicBlack
are trademarks of Texas Instruments.
Other product or brand names in this manual are registered trademarks or trademarks of their respective owners.
* Unauthorized use of a part or whole of the contents in this manual is prohibited.
* The contents of this manual are subject to change without notice.
10
Installation
2
ENGLISH
Chapter 2
Network Board
OWNER’S MANUAL
11
Chapter 2 Installation
Flow of installation
The following are instructions for attaching this product to the projector and connecting it to the network. Please review the entire procedure to become familiar with it.
1 Function of the Network Board (☞ p.13)
Check the contents of a package. This product contains a network board,
owner’s manuals (2 books), a ferrite core and 2 screws. Also check the name
and function of each part.
2 Installation and network configuration (☞ p.14-23)
1 Mount this product onto the projector.
2 Connect the LAN cable and join it to the network.
3 Configure the network of the Network Board.*
4 Set the password.*
1
1
*1
The procedure of the network setting up and network PIN code/Password
may differ from the actual depending of the projector's model types.
See pages 16 to 19 for the case "Projector provides the Network main menu".
See pages 20 to 22 for the case "Projector provides the Network sub menu in
the Setting main menu".
Set up is completed.
The preparation to control the projector connected to the network is completed. At the
next step, set up and control the projector via the network by using the web browser
installed on your computer. Please see chapter 3 “Basic setting and operation”. (☞ p.25)
12
Name and function of each part
z Name and function of each part
Serial port switch socket
This is to switch the polarity of the
serial port. (☞ p.65)
ACT indicator (Green)
This turns on and off when sending
or receiving data
LINK indicator (Orange)
LAN port
Connecting the LAN cable.
(☞ p.15)
!
Serial port
This is used when controlling the
external equipment via the network. (☞ p.61)
ENGLISH
This lights up orange when the network board is connected to the network correctly.
Caution
✐ Do not touch the connector. It may damage the product.
Network Board
OWNER’S MANUAL
13
Chapter 2 Installation
x Installation and Network configuration
Mounting
1 Turn the Mains switch off.
NOTE;
When replacement of terminal board,
MAIN ON/OFF switch should be OFF
position.
Mains Switch
2 Remove
2 screws on a board
from any of the slots 1 to 4*,
and then pull the board out from
the projector.
* The number of the slots may
differ from the actual depending on type of the projector.
3 Put the Board into the board slot
along the guide. Mount the
board connector into the socket
in the slot firmly.
Guide
4 Secure the board with two screws
(supplied).
* Mounting example of the 2 slots model.
!
Caution
✐ Mains switch must be turned off when mounting or removing this product otherwise it may
damage the product.
✐ Do not install multiple network boards into a projector otherwise it may damage the product.
✐ Do not connect the AC cord until after connecting the LAN cable and computer.
14
Connection of LAN cable
Connection of LAN cable
To connect to the network, it is required to use the UTP (Unshielded Twisted Pair)
strait cable with RJ-45 plug. There are two different types of cables depending on
whether the network is constructed with 10Base-T or 100Base-TX. Prepare the Hub
(10Base-T or 100Base-TX) to distribute the network cable if required.
1 Turn the Mains switch off.
2 Wind the UTP straight cable once
around the ferrite core (supplied)
as the illustrated below.
Mains Switch
Ferrite Core
3 Connect the UTP straight cable to the LAN port on the network board.
4 Connect the UTP straight cable to the hub.
Projector
ENGLISH
Hub
(10Base-T, 100Base-TX)
UTP straight cable
✐ Use the UTP cross cable when you connect the computer and projector directly not using the
hub.
✐ When you connect the projector into the 10Base-T network, use cable with category 3 or 5.
When you connect the projector into the 100Base-TX network, use cable with category 5.
✐ The length of cable between hub and projector should be less than 100m.
Network Board
OWNER’S MANUAL
15
For the Projector which provides the Network main menu
Chapter 2 Installation
Network configuration (Type1)
Confirmation of the network menu
When installing this product to the projector, the network on-screen menu items for
this product are activated automatically. If not activated, the product may not have
been installed correctly. Please check item “Mounting” (☞ p.14).
Configure the network
When you connect the projector to the network, the network number of projector
must be the same as the network you intend to connect. You should configure projector’s network first.
This example explains how to set the following configuration.
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.1.201
: 255.255.255.0
: 192.168.1.1
: 0.0.0.0
The default network configuration is set as follows.
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 0.0.0.0
1 Selection of network menu
Turn on the projector and display the menu on the screen. Select network icon
from the main menu and then press SELECT button once. Check that the mode is
"On". If not, change mode to "On" using the point buttons (7 8).
Network icon
Select "On" or "Off"
with 7,8 button
* The above on-screen display may differ from
the actual display depending on the functions
of the projector you use.
16
For the Projector which provides the Network main menu
Network configuration
2 Configuration for IP Address/ Subnet mask/Default Gateway*/DNS*
Press SELECT button again. The following network setting pallet appears on the
screen.
Enter the specified network addresses.
The red frame moves
sequentially left or right with
7 8 button.
The number up or down with
d e button.
How to enter the numbers
There are 2 ways to enter the numbers, one is by using the point buttons (d e )
on the remote control or on the projector, the other is by using the screen 10-key
pallet by which the numbers can be entered directory. For further information see
"How to enter the numbers with the screen 10-key pallet" (☞ p.19).
3 Restart the Network board
After completing the entering of address, select "Set"
and press SELECT button. The network unit starts rebooting and displays message "Please wait..." on the
screen until the re-booting is complete. Do not turn
off the mains switch during this period.
Completing of installation
Item
Description
IP address ..........Sets IP address of the projector
Subnet ..............Sets Subnet mask. Normally sets 255.255.255.0
Gateway*1 ........Sets IP address of the default gateway (Router)
DNS*2 ..............Sets IP address of the DNS server. Must be set when using the e-mail function
ENGLISH
Now the installation is completed. The IP address of this projector is set to
“192.168.1.201”.
*Refer to the projector's owner's manual for operation of the projector.
*1 In the network environments not using a Gateway or Router, the Default Gateway address
should be set to [0.0.0.0].
*2 If you do not use the functions E-mail or DNS server, it should also be set to [0.0.0.0] for the
DNS address.
Network Board
OWNER’S MANUAL
17
For the Projector which provides the Network main menu
Chapter 2 Installation
Network PIN code setting
The Network PIN code can be set to restrict access to the setting page of the projector using the web browser.
✐ Default Network PIN code [0000] means no Network PIN code is set.
1 Displaying Network PIN code menu
Select network menu and then select "Network PIN code" sub menu. Press SELECT
button twice to display the Network PIN code entry pallet.
* The number on the pallet is the current Network PIN code.
Network icon
Network PIN Code
The red frame moves sequentially left or right with 7 8 button.
The number up or down with d
e button.
2 Entering the Network PIN code
To enter the Network PIN code, use point buttons
(ed7 8) on the projector or the remote control.
3 Fixing the Network PIN code
After entering a 4-digit number, select "Set" by
using point buttons (7 8) and then press
SELECT button.
✐ The screen 10-key pallet can be used for entering the Network PIN code. See item
"How to enter the numbers with the screen 10-key pallet" (☞. 19)
✐ It is recommended to set up the Network PIN code when you connect the projector to the
network. This setting is carried out through the projector’s menu and also it can be set
through the network using the web browser. For further information please refer to item
“Initial Setting/Password setting” (☞ p.30).
✐ Valid characters for password are only 4 digits numeric numbers 0 to 9. The number “0000”
means no password set.
✐ This Network PIN code is not to restrict the use of the projector. This Network PIN code is to
set the security against the use of the projector through the network.
18
For the Projector which provides the Network main menu
Network configuration
How to enter the numbers with the screen 10-key pallet
1. Select a column with a red frame by using the point buttons 7 8 .
2. Press SELECT button. The screen 10-key pallet appears on the screen.
3. By using the point buttons(d e 7 8), select numbers 0 to 9 and press SELECT
button. By repeating the above to enter the complete number on the column.
*To change the number in a column, select “C” and press SELECT button to clear the number in the column and then enter the number again.
4. After entering the number in the column, select a move key (7 8 e d) located on
the lower part of the pallet by using the point buttons and press SELECT button
repeatedly to move the red frame.
5. Repeat steps 3 to 4 for entering all the network address.
6. After finishing, select “Exit” and press SELECT button. The 10-key pallet disappears on the screen.
10-key pallet
ENGLISH
Exit
Network Board
OWNER’S MANUAL
19
For the Projector which provides the Network sub menu in the Setting main menu
Chapter 2 Installation
Network configuration (Type2)
Confirmation of the network menu
When installing this product to the projector, the network on-screen menu items for
this product are activated automatically. If not activated, the product may not have
been installed correctly. Please check item “Mounting” (☞ p.14).
Configure the network
When you connect the projector to the network, the network number of projector
must be the same as the network you intend to connect. You should configure projector’s network first.
This example explains how to set the following configuration.
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.1.201
: 255.255.255.0
: 192.168.1.1
: 0.0.0.0
The default network configuration is set as follows.
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 0.0.0.0
1 Selection of network menu [Network]
Turn on the projector and display the menu on the screen. Select the Network icon
from the Setting sub menu using the point buttons (d e 7 8) and then press the
SELECT button on the remote control or on the projector. Confirm that its mode
is set "On". If not, change mode to "On" using the point buttons 7 8.
* The above on-screen display may differ from
the actual display depending on the functions
of the projector you use.
20
For the Projector which provides the Network sub menu in the Setting main menu
Network configuration
2 Configuration for IP Address/ Subnet mask/Default Gateway*/DNS*
Press the SELECT button again, the following network setting menu appears on
the screen. Enter the specified network address with the point buttons (d e 7
8). The following is an example of a network configuration.
NETWORK SETTING
168
IP Address 192
255
255
Sub net
192
168
Gateway
0
0
DNS
1
255
1
0
201
0
1
0
SET
CANCEL
How to enter the numbers
To move the selection and change the values, use the point buttons (d e 7 8) on
the projector or on the remote control.
The point buttons 7 8 are used to select the column.
The point buttons d e are used to change the numbers up and down.
3 Restart the Network board
Select the SET with the point buttons ( 7 8) and press the SELECT button again.
The network configuration display disappears and the network board begins
restarting*1. It takes about 40 seconds. Do not turn off the mains switch during
this period.
Completing of installation
ENGLISH
Now the installation is completed. The IP address of this projector is set to
“192.168.1.201”.
* In the network environments not using a Gateway or Router, the Default Gateway address
should be set to [0.0.0.0]. If you do not use the functions E-mail or DNS server, it should also
be set to [0.0.0.0] for the DNS address.
Network Board
OWNER’S MANUAL
21
For the Projector which provides the Network sub menu in the Setting main menu
Chapter 2 Installation
Password setting [Display]
A password can be set to restrict access to the setting pages of the projector using
the web browser. The default password is set “0000” as no password.
Password
0
SET
0
0
0
CANCEL
1 Use the projector’s menu and select the Setting icon on the menu.
2 Select the Display sub icon from the submenu, and then press the SELECT button
once. Check that the mode is “On”.
3 Then press the SELECT button once again.
*The setting window appears. The numbers on the display indicates the current password.
4 Enter your desired number by using the point buttons on the projector or remote
control, and then select SET and press the SELECT button.
*The password setting window disappears and the Network Board begins restarting. It takes
about 40 seconds. Do not turn off the mains switch during this period.
✐ Password setting must be done when you connect the projector to the network. This setting
is carried out through the projector’s menu and also it can be set through the network using
the web browser. For further information please refer to item “Initial Setting/Password setting” (☞ p.30).
✐ Valid characters for password are only 4 digits numeric numbers 0 to 9. The number “0000”
means no password set.
✐ This password is not to restrict the use of the projector. This password is to set the security
against the use of the projector through the network.
22
Network configuration
Notice about system construction
For installation of multiple projectors into the same network with
Network Board.
Do not install multiple projectors with Network Boards that have their default network settings to the same network. The use of the Network Boards which have the
default IP address set to the same network settings will cause IP addresses to collide
and create a malfunction. When you install multiple projectors into the same network, configure the network with the following steps.
1. Change the IP address from the default IP address. To change the IP address, use
the network setting menu on the projector. Please see chapter “Network
Configuration” for further information (☞ p.16-22).
2. Make sure that there is no network equipment set with the same IP address in the
network, and then connect to the network.
3. When installing other projectors, follow the above steps to change the IP address
and connect to the network.
In case of installing the projector with Network Board into the network
constructed with the DHCP/BOOTP server.
ENGLISH
This Network Board does not support the DHCP/BOOTP server. The static IP address
must be manually configured. To use this product in this network environment, set it
up so that the DHCP/BOOTP server does not assign the IP address configured to this
product for another device on the network. Please consult your network administrator for further information.
Network Board
OWNER’S MANUAL
23
Chapter 2 Installation
24
Basic Setting and Operation
3
ENGLISH
Chapter 3
Network Board
OWNER’S MANUAL
25
Chapter 3 Basic Setting and Operation
This chapter describes basic operations and settings for controlling the projector via a
network using this product. It is required that computer and projector are connected
to the network and the network address be properly configured.
Login the setting page of the projector
1 Enter the IP address
Launch the web browser installed in
your computer, enter the IP address into
the “Address” on the browser and then
press the “Enter” key.
Enter the IP address that you configured in chapter “Network Configuration” (☞ p.16-22). The
default IP address is [192.168.0.2].
2 Select a display mode and login
This product provides 2 types of control mode, Graphic Mode and Text Mode as
the below. Select a proper mode to match your computer and network environment by clicking on the text link.
Once you select your desired display mode, the setting page you selected display
mode will be displayed automatically from the next login. To change the display
mode, click "Top" on the lower-left corner of the setting page (☞p.27).
Graphic Mode
Text Mode
Displays with 600 x 400 dots and
the menus and settings with
graphic icons. This mode is recommended for standard use.
Displays with 200 x 300 dots. This
mode is optimized for use of the
handheld computer, PDA, etc. It is
also convenient if the network
traffic is heavy.
If the setting page has set the password, the authentication window will appear. In this case type “user” onto
the User Name text area and the login password onto
the Password text area and then press the OK button.
* The entering User Name must be “user” and it cannot
be changed.
[Note]
When accessing projector for the first time or setting the no password [0000], the auto-login
will be performed and the next main setting page is displayed.
26
Login the setting page of the projector
3 Display of main setting page
The following main setting page will be displayed according to your display mode
selection. Perform the various kinds of setting through this page. Click on the
linked text to display the control and setting pages.
z Main setting page in the Graphic Mode display
Control sub menu
For selection of
sub menu to control and set the
projector.
Main menu
For selection of control and setting items of the projector.
(☞ p.35)
Setting page
Displays the control and setting
items according to the selected
menu. The “Power & Status”
page is displayed as the default.
Functions of a representative projector model are mentioned in this manual.
Available functions may differ from the actual depending on the projector's
model type. The mark of "--" may appear if the projector does not support the
function. Please see the owner's manual of the projector to know available
functions.
ENGLISH
Setting page number
browses pages by
clicking the linked
number.
* This graphic mode display is mainly used through this manual for the setting and
control description.
Network Board
OWNER’S MANUAL
27
Chapter 3 Basic Setting and Operation
x Main setting page in the Text Mode display
Main menu
For selection of control
and setting items of the
projector. Displays sub
menu and status of
selected items when
clicking the linked text.
Returns to the display mode
selection page.
Setting page number
Browses pages by clicking the linked number.
Setting page
Displays the control and
setting items according
to the selected menu.
28
Initial Settings
Initial Settings
After installing this product to the projector, perform the following basic initial setting.
Click on the Initial linked text on the main menu to display the initial setting page.
The Languages, Date/Time and Password can be set in this page. The model name of
the projector on which this product is mounted is displayed on the page.
Projector’s
model name is
indicated.
1 Language Setting
This setting is to select the display language of the web page. Select your language with the pull-down menu button and then press the Set button. The selectable language is English or Japanese. You may find the unrecognized character
text in the menu if the computer does not provide Japanese fonts.
Network Board
OWNER’S MANUAL
ENGLISH
[Note]
This language selection is realized by using the JavaScript function of the web browser. If the
preference of the browser is set not to use the JavaScript, the “Set” linked text appears on the
page as the below. Click on its text to change the language display. There are various kind of
ways to change this preference depending on the web browser's version and application.
Please refer to chapter “Appendix: Web browser setting/Active Script (JavaScript enable)” (☞
p.72).
29
Chapter 3 Basic Setting and Operation
2 Password Setting
This page is to set the password to restrict the access from an unauthorized person through the network.
Enter the password onto the text box and press the Set button.
The Network Board begins restarting and it takes about 40 seconds. Close (Quit)
the web browser and access to the login page again in 40 seconds. This is to perform the login authentication firmly.
The default password [0000] means no password. You should change password
from the default in normal use. When you connect the projector with this product
to the network, you should set a password. Only a four-digit numeric number is
valid characters for the password.
* If you forget the password to the projector, you can check it with the menu on the projector. For further information, please see item "Network PIN code"(☞ p.18) or “Password
Setting” (☞ p. 22).
3 Date/Time Setting
Click on the page number “2” to display the Time Setting page.
Type present date onto the
date text area with
(Year/Month/Date) format
and type present time onto
the time text area with
(Hour:Minute) format in 24
hours indication. Press the
Set button and confirm that
the data and time are set
correctly. The displayed
date and time are not
updated automatically,
press the Refresh button to
get the present date and
time.
!
Caution
Use of Battery
This product provides a lithium battery. When the battery runs down, the clock and timer functions do not operate properly. Contact your local dealer for the replacement of battery. The
replacement must be carried out by a qualified service personnel. Prohibit the battery replacement by user because of a risk of explosion.
30
Network Configuration
Network Configuration
Click on the Network Setting linked text on the main menu. The following
setting page is displayed. This page is to set the IP Address, Subnet Mask,
Default gateway, DNS (Domain Name Server) and projector name.
1 Configure the network
The IP address and Subnet Mask have been configured already in chapter
“Installation”. If you want to change them or configure default gateway*1 or
DNS*2, perform them in this page. Enter an applicable address number onto each
parameter and press the Set button.
The Network Board begins restarting and it takes about 40 seconds. Close (Quit)
the web browser and access to the login page again in 40 seconds.
✐ You must use the number specified by your administrator. The address must be entered
as a group with four numbers split by dots like [192.168.1.101].
You can name*3 the projector. By setting this name
properly for the DNS server, the projector can be
accessed by using this name instead of the IP
address.
For further information, please consult your network administrator.
ENGLISH
2 Name the projector
*1 Set [0.0.0.0] if the network does not provide the gateway (router).
*2 Set [0.0.0.0] if you do not use the function E-Mail alert.
*3 If you use the DNS server, register the host name registered to the DNS server as a projector name. You can access with this projector name from any computers in your network. If
you do not use the DNS server, access with the IP address assigned to the projector.
Network Board
OWNER’S MANUAL
31
Chapter 3 Basic Setting and Operation
E-mail Setting
This product has an E-mail function which can send an alert message to
users or an administrator if it detects an abnormality on the projector or run
out of the life span of the lamp. Click on the E-Mail Setting linked text on the main
menu and follow the below steps.
1 Registering SMTP Server*1, Administrator Address
Type the E-mail address of SMTP server and administrator and press the Set button. The administrator address is set to "Reply-To" address sent from the projector.
*1 The SMTP server is a server for sending E-mail. Please contact your network administrator to have this SMTP server address.
* If the network board sends an alert message due to the abnormality on the projector but
the SMTP server is down in some reason, the message will not be sent. In this case, the
message "Unable to connect to server" will be displayed on this page. To clear this message,
click the Set button.
✐ To use the E-mail function, it must be set the DNS address on the Network Setting page correctly.
✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in
your network environment. If the SMTP server is located in your LAN (Local Area network),
the address set to SMTP server should be specified in the SMTP server located in your LAN.
The server located outside of your LAN may not be available for security reason. For further
information please contact your network administrator.
✐ Up to 10 e-mail addresses can be registered.
32
E-Mail Setting
2 Registering and deleting E-mail addresses
Type the E-mail address onto the Mail
Address text area and press the Set button.
To check the registered addresses, click on
the Mail Address Check & Delete
linked text. The addresses are
listed as the figure on the right.
To delete the registered addresses,
check the address you want to
delete and press the Delete button.
3 Condition selection for sending alert message
Click on the Option linked text. Check the
condition items under which alert messages will be sent and press the
Set button.
ENGLISH
Please refer to chapter
“Examples :Type and contents of alert messages”
described on the next page.
* The mail option item may differ from the actual depending on the projector's function.
Network Board
OWNER’S MANUAL
33
Chapter 3 Basic Setting and Operation
Examples: Type and contents of alert mail
When the projector has an abnormality, the following alert messages are sent to the
registered E-mail address according to your selected condition. Administrator or user
can take an efficient action quickly by receiving this massage. This is very useful to
maintain and service the projector.
The following are examples of received messages.
● When the internal temperature is too high:
TITLE: Message from projector
01-12-2007 00:59
Projector Model Name: Model Name
TCP/IP: 192.168.0.2 Projector Name: myProjector
It sends you following massage.
*The Projector lamp is turned off, because internal projector temperature is too
high.
Wait Temperature Warning Indicator turned off,turn the Projector on again.
If the Indicator continues to flash,check the air filter for dust accumulation.
[A] 36.5 Degree [B] 58.2 Degree [C] 37.8 Degree
Temperature of Sensor B is too high.
✐ The Network Board let users know which thermal sensor [A], [B] or [C] inside the projector detected the
abnormal temperature risen and so the projector was turned off. Please refer to item “Check the status
of projector” for the location of the sensors [A], [B], [C], and temperature (☞ p.37). Also see the owner's
manual of the projector for further details.
* Sensor [C] may not be supported depending on the projector models.
● When projector needs service:
TITLE: Message from projector
01-012-2007 00:58
Projector Model Name: Model Name
TCP/IP: 192.168.0.2 Projector Name: myProjector
It sends you following massage.
*Maintenance requirement from Projector is detected.
Check up LED statues of projector and consult with the dealer.
Information : FFFEFFFF
✐ Maintenance requirement from Projector is detected. Unplug the AC power cord and plug it, and
then turn on the projector once again to verify operation. If the problem still persists, unplug the AC
power cord and ask servicing to a qualified service personnel with the information code.
* Contents and format of the information code may differ from the actual depending on each projector's model type.
● When the life span of lamp is reached:
TITLE: Message from projector
01-12-2007 00:58
Projector Model Name: Model Name
TCP/IP: 192.068.0.2 Projector Name: myProjector
It sends you following massage.
*The life span of lamp2 is reached.
Lamp2 replacement is required.
Lamp1 ON 350 h
Lamp2 ON 500 h
Lamp3 ON 60 h
Lamp4 ON 350h
34
✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent to users every time the projector is turned
on. This alert mail will not be sent when unchecking the mail sending condition “When the life
span of lamp is reached”.
* Lamp3 and Lamp4 are not indicated if the projector support dual lamp system only.
Controlling the Projector
4
ENGLISH
Chapter 4
Network Board
OWNER’S MANUAL
35
Chapter 4 Controlling the Projector
Power on/off the projector
Click on the Power & Status linked text on the main menu. The control page
will be displayed.
By Pressing the On or Standby button on the page, the power of the projector can be
controlled. When you press the Standby button, another confirmation popup window*1 will appear, and then press the OK button if it is set to standby.
[Note]
*1 This popup window is realized by using the JavaScript
function of web browser. If the preference of the browser
is set not to use JavaScript, the popup window will not
appear on the screen.
There are various kind of ways to change this preference
depending on the web browser's version and application.
Please refer to chapter “Appendix: Web browser
setting/Active Script (JavaScript enable)” (☞ p.72).
✐ The projector is not turned on for about 90 seconds after switching into the standby mode.
After the power status indicator on the control page changes from “On Cooling down” to
“OFF”, then try to turn on the projector with On button.
✐ The web browser checks and updates projector's condition every 20 seconds automatically.
36
Check the status of projector
Check the status of projector
In the “Power & Status” page, you can control the projector power, and also you can
check the status of the projector as follows. To change the page, click on the page
number linked text.
Items
Description
Yellow
....................Normal
Red
....................Lamp replacement required
Gray
....................Off
Gray with X
....................Abnormality of the lamp
Accumulated
Lamp-use Time ..............Displays the accumulated lamp use time in hour units (h) and displays each
time with Lamp1/Lamp2/Lamp3/Lamp4 order.
Accumulated
Projector-use Time ..........Displays the accumulated projector use time in hour unit (h).
Power Status ..................Displays the status of the lamp.
Projector Condition* ........Displays the status of the projector's power.
* When occurring the internal power failure, The word “Power Failure” and error
information is displayed.
Input Status ....................Displays the selected input.
Selection..........................Displays the selected input mode.
Signal Status ..................Displays the signal status of the selected input mode.
Inside temperature ..........Displays the internal temperature of the projector. The icons [A], [B], [C] on
the page represent the thermal sensors*2 located in the projector. If the temperature at one of those sensors exceeds specified temperature, the appearance of its icon changes to the following alert icon to let users know about
the abnormal temperature. Please check surrounding temperature of the projector, check for clogged air filters and check area surrounding the ventilation
fans.
ENGLISH
Lamp Mode ....................Displays 2 lamps or 4 lamps mode and lamp status as below icons with
Lamp1/Lamp2/Lamp3/Lamp4 order.
The icons [A] , [B] and [C] represent the sensors located in the projector as follows:
[A]: Surrounding temperature of the projector*1
[B]: Internal temperature of the projector
[C]: Internal temperature of the projector*2
*1 The indicated peripheral temperature of the projector is a little higher than actual surrounding temperature.
*2 Sensor C icon may not indicated depending on the projector's model type.
Network Board
OWNER’S MANUAL
37
Chapter 4 Controlling the Projector
Control the projector
The control menus are displayed on the upper side of the page. When you click each
control icon, the control page is displayed according to the control menu you selected. The setting method differs depending on the contents of the page. Click on the
page number linked texts to change pages and select desired setting items.
✐ Please see the owner's manual of the projector to have the further information of
each control item.
✐ If the adjustment items are not required by the projector itself or input signal, the
mark of "--" may be indicated.
✐ The control page displays valid control items depending on the selected input mode, signal or
functions of the projector you use, therefore, there may be different controls between the
described items and actual control items on the page display.
✐ When the projector is in standby, only the timer on the setting menu is effective; others are
inactive.
Input
This function is to select the input mode and slot to the projector. Select
the input slot with the radio button, and input source mode with the pulldown menu button. Then set the selected input source and source mode
by pressing the Set button.
Select a slot with
radio buttons.
Select a source
mode with pull-down
menu.
Item
Description
Input(SLOT) ......Displays input number and
board name installed in the projector. The setting items differ
from the actual depending on
the board function.
Mounted Board name
* Available slots and indications may differ from the
actual depending on the projector's model type.
38
Control the Projector
PC Adjustment
This function is to adjust the signal from the computer connected to the
projector to obtain the proper picture image on the screen. Click on the
page number linked texts to change the setting pages.
Item
Description
Current Mode ........Displays current mode of the
computer.
Auto PC Adj. ......Performs automatic adjustment.
Fine Sync...........Performs Fine Sync adjustment.
Total Dots ..........Adjust the number of total dots
in the horizontal period.
Horizontal ..........Adjusts horizontal picture position.
Vertical ..............Adjusts vertical picture position.
Item
Description
Clamp ................Adjusts clamp position of the
picture.
Display Area H ......Adjusts the image area horizontally.
Display Area V ......Adjusts the image area vertically.
Full Screen* ......Makes the image full screen
display.
ENGLISH
* This function is not available for some projector's model types. In such a case, please refer
to the section of the screen adjustment (p.44)
✐ These parameters will appear only when the analog computer input mode is selected.
Network Board
OWNER’S MANUAL
39
Chapter 4 Controlling the Projector
Save a Set
1 Decide your desired PC adjustment values through the PC Adjustment pages
“1”to “2”.
2 Display the page “3” and select a mode
number*1 with the pull-down menu button of the Save to. Type a memo into the
Memo text area for simple description of
your selected number.
3 Register by pressing the Set button.
To restore the adjustments, press the
Reset button.
It is displayed with “Stored” or “Free” for
the memo of Mode1 to Mode5. The memo
of ExMode6 to ExMode50 can be stored
into the selected mode.
Select a mode by
clicking the button
Type a memo for
the selected mode
Load a Set
Select a set to load with the pull-down menu button of the Load Setting No. and press the
Set button. The stored setting values will be applied to the each PC adjustment item.
Select a load mode
by clocking the button
*1 Available mode may differ from the actual depending on the projector's model type.
Type1: Mode1 to Mode5, ExMode6 to ExMode50
Type2: Mode1 to Mode10, ExMode11 to ExMode50
✐ The Display settings can be stored up to 50 sets, Mode1 to Mode5(Mode10) are stored into
the projector and ExMode6(ExMode11) to ExMode50 are stored into the Network Board.
40
Control the Projector
System Adjustment
This function is to select the color system of video signal or scanning system of component signal input to the projector. Select a system with the
radio buttons to match the color system or scanning system of input
source, and then press the Set button. The displayed systems are switched according to the input mode.
Available selection when the VIDEO/S-VIDEO input
Item
Description
Color System ....Selects a color system of the
input video signal.
AUTO ................It automatically switches to the
color system of the input signal.
Available selection when the Y, Cb/Pb, Cr/Pr input
Item
Description
ENGLISH
System ..............Selects a scanning system of
the input component signal.
AUTO ................It automatically switches to the
scanning system of the input
signal.
✐ These selections will not appear when the source mode is set to the computer mode.
Network Board
OWNER’S MANUAL
41
Chapter 4 Controlling the Projector
Image Adjustment
This function is to adjust the projected picture image and set the image
mode. For selection of image mode, select a desired image mode with the
Image Adjustment Mode pull-down menu button and then press the Set
button. The setting items are switched automatically according to selected input
mode, computer or video input.
Item
Description
Image Adjustment*. Selects image mode among
the Standard, Real, Cinema,
Dynamic, Image1 to Image4
with pull-down button menu .
Image1 to 4 are user preset
mode.
Original Mode ........Displays which predefined
image adjustment mode is
based upon.
Adjustment
items ..................Contrast, Brightness, Color, Tint
BrilliantColor............Improve the color performance
with BrilliantColorTM technology.
* Available image mode may differ from the actual
depending on the projector's model type.
Type1: Image1 to Image4
Type2: Image1 to Image10
Item
Description
White Balance
Color Temp. ......Sets a color temperature mode.
Red, green,
Blue ................Adjusts a white balance
respectively.
Item
Description
Sharpness..........Adjusts picture sharpness.
Gamma ..............Adjusts brightness of darker
part of the picture.
Noise
Reduction ..........Switches noise reduction
on/off.
Progressive ..........Switches progressive mode.
Save Adjustment ....Select a mode to store the
image adjustment values.
* The displayed adjustment items may differ from
the actual depending on the functions of projector
you use. The error message may appear if the
projector does not support the function.
42
Control the Projector
Save a image adjustment value
1 Decide
2
your desired image adjustment
value through the image adjustment
pages “1” to “3”.
Display the page “3” and select the
desired image number*1 with the pulldown menu of the Save Adjustment.
3 Register by pressing the Set button.
To restore the adjustments, press the
Reset button.
The Image1 to Image10 are for the user preset modes to store the image adjustment.
The Original Mode is represented the mode that user preset mode Image1 to
Image10 is created from the predefined image modes Standard, Real or Cinema.
Load a image mode
ENGLISH
Display the page “1” and select a set to
load with the pull-down menu button of
the Image Adjustment Mode and press
the Set button.
*1 Available image mode may differ from the actual depending on the projector's model type.
Type1: Image1 to Image4
Type2: Image1 to Image10
Network Board
OWNER’S MANUAL
43
Chapter 4 Controlling the Projector
Screen Adjustment
This function is to adjust the screen mode of the projector. The setting
items are switched automatically according to selected input mode, computer or video input.
Item
Description
Screen*1 ............Changes the screen mode.
Aspect*1 ............Changes the screen mode.
Computer Input Normal/True/Wide/
Full screen/Custom
Video Input
Normal/Wide/Custom
True*2 ................Switches the projected image
mode.
Digital Zoom*3....Adjusts the image zooming or
compressing.
*1 Either of item "Screen" or "Aspect" is available
depending on the projector's model type.
*2 Item "True" is not available depending on the
projector's model type. In that case, use the
screen item.
*3 These items are only available in the computer input mode.
* There may not be available depending on the
projector's model type.
Sound Adjustment
This function is to adjust the sound of the projector. The values in each
text box represent the current control value or status.
Item
Description
Volume ..............Adjusts the sound volume from
the built-in speakers.
Treble ................Adjusts the high-frequency
sound band.
Bass ..................Adjusts the low-frequency
sound band.
Built-in SP ..........Switches the sound output
from the built-in speaker
Mute ..................Suppresses the sound.
* There may not be available depending on the
projector's model type.
44
Control the Projector
Setting
This function is to set up the projector. Click on the page number “1” to “5”
linked texts to change the setting pages.
Item
Description
Language ..........Changes the on-screen menu
language of the projector.
Keystone* ..........Corrects the keystone distortion of the projected image on
the screen. It moves quickly if
the “High Speed” is checked.
* The control button [Left], [Right] may be not available depending on the projector's model type.
Item
Description
Background* ......Sets screen background when
no input signal received
Blue Back* ........Sets screen background color
when no input signal received.
Display ..............Sets on-screen menu display
Logo ..................Sets the logo display setting on
the screen during the startup.
Ceiling................Sets the image top/bottom and
left/right reversed.
Rear ..................Sets the image left/right
reversed.
* Either of item "Blue Back" or "Background" may
appear depending on the projector's model type.
Description
Shutter*1 ............Sets the image black out mode.
No Show*1 ..........Sets the image black out mode.
Freeze................Sets the image frozen mode.
Power
Management......Sets the power management if the
input signal is interrupted and no
control key is pressed during the
specified period of time.
Sets the time periods*2 until the
power management operates.
On Start ............Sets the power-on mode when
turning on the mains switch.
Lamp Mode........Switches lamp mode 1 lamp or
2 lamps mode, or 2 lamps or 4
lamps mode.
Lamp Control* ..Switches lamp control mode
*1 Either of item "No Show" or "Shutter" may appear
depending on the projector's model type.
* The displayed items may differ from the actual *2 The time cannot be setup depending on the prodepending on the functions of projector you use.
jector's model type. In this case please see the
The Error message may appear if the projector
projector's owner's manual.
does not support the function.
Network Board
OWNER’S MANUAL
ENGLISH
Item
45
Chapter 4 Controlling the Projector
Item
Description
Lamp Interval ....Sets the interval period of
switching two lamps.
Remote Control ......Sets the remote control codes.
Lamp Counter
Reset ................Resets the lamp use-time.
Reset when replaced lamp.
P-TIMER ............Used to display the timer on
the screen. The status is
changed as ON -> STOP ->
OFF when this button is
pressed repeatedly.
Factory Default ..Restore the value of the setting
items to the factory default
value.
* There may not be available depending on the
projector's model type.
About Lamp Counter reset
The confirmation window as the left will
appear when the Reset button of the “Lamp
Counter Reset” is pressed. Select which
lamp counter is to be reset with the radio
button and then press the OK button.
* There may fail to be
(Set JavaScript On)
(Set JavaScript Off)
reset depending on
the projector’s type.
* In case of 2 lamps model
Item
Description
Actual Time........Displays the current time set to
the projector.
Timer Setting ....Function to switch on or off the
projector at the programmed
date and time. Please see
chapter “How to set the
Timer” for further instructions.
* Please see the pages 48 - 49 for details.
✐ There are various kind of ways to change the JavaScript preference depending on the web
browser's version and application. Please refer to chapter “Appendix: Web browser
setting/Active Script (JavaScript enable)” (☞ p.72).
46
Control the Projector
Item
Description
HD data wireless ......Sets the HD data wireless
board.
Mode select ......Switches the communication
mode (Single mode or
Broadcast mode).
Authentication ....Executes or resets the authentication at the Single mode.
ID input ..............Inputs ID number at the broadcast mode.
Reset ................Restore the value of the HD
data wireless setting items to
the factory default value.
* There may not be available depending on the
projector's model type.
Item
Description
Picture in Picture ......Sets the “P in P” or “P by P”
mode which has been preset in
the setting menu. (OFF, User1
- User5)
Edge blending....Sets the seamless overlapping
for multi-screen.
Color matching ..Corrects the difference of color
for multi-screen.
DynamicBlack ....Improve the black level of the
image. (OFF/Low/High)
HDMI setup........Switches Normal or Enhanced
according to the HDMI source.
ENGLISH
* There may not be available depending on the
projector's model type.
✐ When the Picture in Picture mode is ON, there are some restrictions as follows;
- The last memorized input source is displayed in Input menu.
- “PC Adjustment”, “System Adjustment” and “Save Adjustment” are invalid.
Network Board
OWNER’S MANUAL
47
Chapter 4 Controlling the Projector
How to set the Timer
This function is used to turn the
projector off or on at a programmed day/date and time.
Follow the below steps for setting.
Select day
Select date
1 Set a day or date
To set the timer event at
same time everyday,
select “day” entry with radio
button and then select
desired day with the pulldown menu button. The selectable days are as follows:
- Same time everyday
Event
- Every week ( a day from Monday to Sunday)
- Every week (Monday to Friday) - Every week (Monday to Saturday)
To set the timer event on specified date,
select “date” entry with radio button and then type the date with
(Year/Month/Date) format.
Ex.: Type [2007/08/20] if you specify [August 20, 2007].
2 Set a time
Type the time with (Hour:Minute) and 24 hours format.
Ex.: Type [18:25] if you specify [PM 6 o’clock and 25 minutes].
3 Select an event “ON” or “OFF”.
Select an event ON or OFF with the pull-down menu button to turn on or off the
projector.
4 Register an event
Press the Set button to register the set
timer event. Repeat steps 1 to 4 for
another timer event setting.
Check the Timer events
To check the set timer events, click on
the Timer Check linked text.
48
Control the Projector
Getting the current time
The displayed time is the value set when the setting page was displayed. This time
value is not updated automatically. To update the display time press the Refresh button.
Notes on timer setting
✐ Up to 10 timer events can be registered. Timer events always operate according to
the next valid event depending on the projector's power status. In the example
below, event 3 turns on the projector so next event 4 (also turning on projector)
will not be effective because the projector is already turned on. Similarly, when the
projector is turned off by event 5, event 6 OFF will not be effective in turning it off
again. But these secondary events (event 4 and event 6) will become effective if a
person turns off the projector (after event 3 and before event 4) or turns on the
projector (after event 5 and before event 6).
Invalid event
ON
Projector Power
Event 1
Event 2
Event 3
Event 4
Event 5
Event 6
Invalid event
ON
ON
OFF
ON
ON
OFF
OFF
Time
✐ When the timer events are set at the same time, the last event set will override
the previous events. For example, if there is an event like “On at 8:00 everyday”
and then new event is set like “Off at 8:00 everyday”, only the last setting event is
effective.
✐ When the timer event ON occurs during cooling down period, this is invalid event
because the projector cannot be turned on during this cooling down period.
Cancel the timer
ENGLISH
To cancel the timer event, check the
timer event you want to delete and then
press the Delete button.
✐ The timer operates by using the clock function provided in this product. Before setting the
timer, please confirm that the current date and time are set correctly. Timer and clock functions are functioning using a lithium battery provided in this product. When the battery runs
down, the clock and timer functions will not operate correctly. Consult your local dealer for
the replacement of battery. The replacement must be carried out by a qualified service personnel.
Network Board
OWNER’S MANUAL
49
Chapter 4 Controlling the Projector
Service
This function sets parameters for service items of the projector. As these
service items are used mainly for maintenance, please use the default setting unless a change is needed. There may be not available items depending on the projector's function.
Item
Description
Fan Control
Speed ................Sets fan control speed.
Prohibition..........Sets the prohibition of the projector control by the remote
control or the keys on the projector.
Item
Description
Video System*1 ..Displays the current video system mode.
H Area*1 ............Adjusts the horizontal effective
area.
V Area*1 ............Adjusts the vertical effective area.
H Position*1 ........Moves image horizontally
V Position*1 ........Moves image vertically.
*1 It cannot be displayed in the computer mode.
* To restore the setting, press the Default button.
* Some projector's model types cannot support
this function.
- The indication of video system in this page is displayed as follows.
Video System
480I
480P
575I
575P
720P60
720P50
1035I
1080I60
1080I50
1080P60
1080P50
Input Signal
NTSC [VIDEO], [S-VIDEO], [Y, Cb/Pb, Cr/Pr]
NTSC [Y, Cb/Pb, Cr/Pr]
PAL [VIDEO], [S-VIDEO], [Y, Cb/Pb, Cr/Pr]
PAL [Y, Cb/Pb, Cr/Pr]
[Y, Pb, Pr]
[Y, Pb, Pr]
[Y, Pb, Pr]
[Y, Pb, Pr]
[Y, Pb, Pr]
[Y, Pb, Pr]
[Y, Pb, Pr]
✐ The adjustments of H/V Area and Position are effective only for video input mode. These
adjustment values are stored with each video system mode as the above.
50
Control the Projector
Save Actual Adjustment
This function is to save and load the control values of the projector. The
storable control items are Input, PC, System, Image and Screen controls.
1 Adjust and set the controls
Set the controls properly according to the selected source. (see pages 38-44 for
further adjustment)
2 Select the Save page
Click on the Save icon from the control
menu. The setting page is displayed as
the right. Change pages by clicking on
the page numbers “1” to “7” linked
text and check the current settings.
For further information please see the
next page.
Select a set
number
Type a memo for the
selected set number
3 Name the current setting
Select a set number (Set1 to set10) you intend to store current settings with the
pull-down menu button of the Save Setting No.: Save to. Name this set number
onto the Memo text area.
4 Save the current setting
Press the Set button to store the current setting and name into the selected set
number.
✐ You can store up to 10 sets of controls into the Network Board.
Check the Save items
ENGLISH
Browse pages by clicking on the page numbers and check each setting status. The
pages for the save items are constructed by 7 pages. The contents of the pages may
differ from the actual depending on the selected input mode and the function of the
projector.
Network Board
OWNER’S MANUAL
51
Chapter 4 Controlling the Projector
Load a control set
Select your desired set number with the pull-down menu button of the Load Setting
No. and then press the Set button. The setting values of the selected set number are
applied to the current settings.
Example of setting
✐ If the contents of the saved set are not match for the slot equipped on the projector, the
invalid alert message may be displayed. For example, the message “Invalid setting for
SLOT1” will be displayed in the following case.
Example: In case of after setting the DVI computer input for SLOT1 and then it was changed
to video input board.
52
Control the projector’s menu
Control the projector's menu
Click on the Menu linked text on the main menu. The following menu control page is displayed. This page is to control the on-screen display menu of
the projector.
Item
Description
ENGLISH
Display Menu ....To switch the on-screen display menu on or off by pressing the ON or OFF button.
The same operation with the MENU button on the projector and remote control handset.
Cursor ................Used to select an item or adjust value in on-screen menu by pressing the Up, Down,
Left and Right button. The same operation with the pointers on the projector and
remote control handset. Used to execute the item selected by pressing the Set button. The same operation with the SELECT button on the projector and remote control handset.
Network Board
OWNER’S MANUAL
53
Chapter 4 Controlling the Projector
Make a memo
Select the Memo setting page by clicking on the Memo linked text on the
main menu. The following setting page is displayed. It is convenient to use
as a memo for the simple description where the projector is placed in. This note will
be displayed on the login page. Input a memo and then press the Save button.
The saved memo is
displayed on the
login page.
54
Controlling the Multi-Projectors
5
ENGLISH
Chapter 5
Network Board
OWNER’S MANUAL
55
Chapter 5 Controlling the Multi-Projectors
Multi-Control
This function enables you to control (Power, Image, Date/Time, Timer,
Screen, etc.) the multiple projectors equipped with the Network Board connected to the network. Click on the Multi Control linked text on the main menu to display the control page.
Note:
To control the multiple projectors, each projector must has the same password.
Example of multi control
PJ4
PC3
PJ3
PC4
Internet
Intranet
PJ2
PJ1
PC5
Select INPUT2
for PJ1 to PJ4
56
Multi-Control
Register IP address and projector
name
Click on the Registration of Projector
linked text to display the registration
page. Type the IP address and projector
name* 1 if required and then press the
Register button.
IP address
Check IP address and projector
name
To check the registered information, click
on the Check & Change linked text. The
registered information of the projector is
listed as the right.
* The word “None” is displayed if the projector name is not registered.
Projector name
ENGLISH
When you click on a listed IP address,
the login page for the selected projector
will be displayed with a new window and
then enter the password for this projector and login.
*1 Normally, the projector in the network is recognized with the IP address. This product allows
you to name the projector instead of the IP address. By registering the projector’s nickname
like “MeetingRoom101”, it can be managed and recognized easily. If you use the DNS server, register the host name registered to the DNS server as projector name. For further information please consult your network administrator.
✐ You can register the projectors up to 100 sets for the multi-control.
Network Board
OWNER’S MANUAL
57
Chapter 5 Controlling the Multi-Projectors
Exclude/Add/Delete a projector
To change the mode of the registered projectors, Select a mode with the pull-down
menu button under the IP address of the
target projector and then press the Set
button.
Status
If some of the registered projectors are
deactivated by some reasons (such as disconnecting the power source, disconnecting the LAN cable, disconnecting from the
network), control changes will continue to
be effective for the projectors that are still
activated. At the same time, the deactivated projectors are excluded from the multicontrol. The status of the registered projectors are indicated under the projector
name. See the table below for status indications.
Status
Mode
Operation
OFF
ON
Delete
: Exclude from the multi-control
: Add to the multi-control
: Delete from the multi-control
Description
(blank)................The projector is connected to the network correctly
No connected ........The projector may not be connected to the network. Please check the connection
and network configuration of this projector.
Password error ......The login password is incorrect. The password for the multi-controlled projectors
must be the same. Change password of this projector to the common password.
✐ If the multi-controlled projector is in the standby mode, any change is not effective except
timer setting.
✐ It is recommended that a specified projector should be chosen for setting when you use this
multi-control function. The control for the multi-controlled projectors will become too complicated operation if this function is used for each projector.
✐ If the registered projector is not connected to the network, it will take some time to complete
the multi-control operation because the network board is waiting for the response from each
registered projector.
58
Control
Control
Display the control page by clicking on
the Control linked text on the multi-control page. The setting pages are constructed from 1 to 6 page and each items
are indicated on the next page.
Load and apply the setting value
ENGLISH
The control sets saved for each projector (☞ p.50) can be used while the multi-controlled projectors function is being used. Select a setting number from the item Load
Setting No. with the pull-down menu button and then press the Set button. The control values stored with selected set number for each projector will be applied to the
individual projector assigned to that set. The same control values will not be applied
to all of the projectors under the multi-control.
✐ If loading a set to the multiple projectors, the contents of the set must be effective to current
accessed projector. If not, the multi-control cannot be performed.
Example: If the DVI computer input for SLOT1 is set into the “Set1” and the current
accessed projector has a video board on the SLOT1, the load set will become
invalid this time and the loading of set for the another projectors will not be carried
out.
Network Board
OWNER’S MANUAL
59
Chapter 5 Controlling the Multi-Projectors
Control multi-projectors at the same time
The valid controls are shown below. Please refer to chapter 4 “Controlling the
Projector” (☞ p.35) for further control and description. When the control button or
setting button is pressed, the registered projectors for the multi-control are controlled
at the same time. * These control items differ from each selected input mode and functions
of the projector you use. Change of function is disable if the multi-controlled projector does not
support its function.
* The above pages are example. They may differ
from the actual depending on the projector's
model type.
60
Use of Serial Port
6
ENGLISH
Chapter 6
Network Board
OWNER’S MANUAL
61
Chapter 6 Use of Serial Port
This product provides a serial control port (RS-232C) to control the external
equipment which has an RC-232C port. This function allows external equipment to be controlled by the computer through the network and the projector can be controlled by the external serial controller. Before connecting the
external equipment, perform the setting “Serial port setting” described
below.
Serial Port setting
This is to set up the serial port on the network board. Display the setting page by
clicking on the Serial Port linked text on the main menu. To communicate with external equipment correctly, communication condition must be set to the same values as
that the connected equipment is using. After fixing the setting, press the Set
button*1.
Item
Description
Baud Rate..........Communication speed for serial port, select with the pull-down menu.
Parity..................Parity check, the ways for error detecting of the transferred data.
Stop ..................Stop bit, indicates the end of communication.
Flow Control ......Ways for communication flow.
Data ..................Indicates the length of data
Serial Control ....Selects equipment to control
External ........Used to select when the external equipment connected to the serial
port is controlled by the computer through the LAN port.
Projector........Used to select when the projector is controlled by the serial controller
connected to the serial port.
Port ....................Indicates the port number of TCP/IP. The default number is 23. Use the same port
number specified by application. There are some reserved port number*2. If one of
those port numbers is used, the alert dialog window will appear and let you know
that it is an invalid port number.
62
Serial Port Setting
Setting to control the equipment connected to the serial port from the
computer
Serial Control
Port
Other Settings
:Selects “External”
:Sets according to the computer specified port no. Do
not use port no. 10000*2.
:Sets according to the communication condition of the
equipment
Setting to control the projector from the serial controller connected to
the serial port
Serial Control
Port
Other Settings
:Selects “Projector”
:Not specified. Do not use
port no. 10000*2.
:Sets according to the communication condition of the
serial controller
Setting to control the projector from the computer through the LAN
port
Serial Control
Port
Other Settings
:Not specified
:Not specified
:Not specified
*1 This product will restart automatically when “Port” or “Serial Control” is changed and it
takes about 40 seconds.
*2 The reserved port numbers are http (80), ftp (21), telnet (23), etc. The port no. 10000 is
reserved to control the projector through the LAN port.
✐ There are 2 types of RS-232C serial cable, Normal(Straight) and Reverse(Cross) type. This
product provides with a serial port switching socket. Set this switch to proper side according
to the cable type. How to switch the serial port socket, see item "Serial Port Switching".(☞
p.61)
✐ Exclusive driver software for control of the external equipment is required. This product does
not provide any driver software. Please consult your local dealer.
Network Board
OWNER’S MANUAL
ENGLISH
* The port no. of the computer must be used with 10000.
63
Chapter 6 Use of Serial Port
Control Examples
Example 1
Controlling AV equipment through network
PC1
PC2
PC3
Turn on the DVD player
and start playing.
PJ2
Internet
Intranet
PC4
PJ1
PC5
DVD Player
RS-232C serial cable
Example 2
Controlling a projector which is not on the network function through network.
PC2
PC4
Turn on the projector PJ1
Internet
Intranet
PJ2
PC5
PJ1
RS-232C serial cable
64
Control Examples
Example 3
Controlling the projector with the serial controller through the serial port (RS-232C).
PC2
PC3
Internet
Intranet
PC4
PJ2
PJ1
PC5
Serial Controller
RS-232C serial cable
Serial Port Switching
When connecting the peripheral equipment to this network board, you should notice
the type of serial cables. At the factory shipping, the polarity of serial port on the network board is set to the reverse (cross) type. When connecting the peripheral equipment, please use an optimum serial cable according to the polarity of the port on the
equipment. And this product provides a socket to switch the polarity of the serial
port. By switching the socket on the board as shown below, it is possible to switch
the polarity of the port either the normal (straight) type or the reverse (cross) type. By
means of this, you can use both kinds of the serial cable. For further pin allocation
please see item "Port Specification".(☞ p. 82)
Serial port
B
A
B
ENGLISH
A
Socket
Socket
Side A: Reverse (cross) type,
factory shipped setting
Side B: Normal (Straight) type
Network Board
OWNER’S MANUAL
65
Chapter 6 Use of Serial Port
Use of Telnet
You can control the equipment connected to the serial port on the Network Board
and the projector itself by using the telnet application*1 installed on your computer.
The following is a control example of external equipment. The telnet application is
needed to use commands*2 which controls the external equipment.
Preparation
1 Turn the projector off with the mains switch and connect an external equipment to
the serial port with an RS-232C serial cable.
2 Turn on the projector and external equipment.
3 Display the setting page by clicking on Serial Port on the main menu with the web
browser. (☞ p.62)
4 Change the serial port setting to be the same communication condition as the connected external equipment and then click Set button.
The following example setting is for our projector
communication condition. When controlling our projector set as follows:
Baud rate ..........19200
Parity ................NONE
Stop ..................1
Flow Control ......NONE
Data ..................8
Serial Control ....External
Port ..................23
Control
(For example, in case of using the Telnet application of the Windows XP Professional.)
1 Select Run... submenu from Start menu on the computer. Type “telnet” onto the
Open text area on the displayed window and press OK button.
2 The telnet application will start and the following window will be displayed. Type as
below to connect the projector.
> open 192.168.1.201 return
* Use the IP
address assigned
to the projector
66
Use of telnet
3 When
communication is established, the word “PASSWORD:” appears on the
window. Type the login password* for the projector and then press “Enter” key on
the keyboard. If you do not register the login password, just press “Enter” key.
When the word “Hello” is replied, login has been succeeded.
* For example,
entering password [1234]
4 Type
the commands from the key board to control the external equipment and
then enter “Enter” key for termination. For example, type “C00” and enter
“Enter” key.
- The extra projector will be turned on.
* “C00” is a command to turn the projector on.
* Enter with ASCII 64-byte capital characters and one-byte characters.
ENGLISH
To disconnect the communication, type “Ctrl” key and “]” key at the same time.
*1 Further instructions about the telnet application, please see the on-line guide on your computer.
*2 The commands are defined by each product independently, so please consult the manufacturer or sales dealer for further information of the commands.
* The password is a login password decided on page 18, 22 or 30. If the authentication of the
entered password is failed 4 times continuously, the communication will be disconnected
automatically. Please try again for the connection.
Network Board
OWNER’S MANUAL
67
Chapter 6 Use of Serial Port
Control the projector with Telnet
This product allows you to control the projector by using the Telnet application.
Normally, it is used for controlling the external equipment connected to the serial port
and also control the projector itself by specifying the telnet port no.10000.
* It is not affected by the serial port setting of the projector when using the telnet application.
In the step 2 of the previous page, enter port no. “10000” after the IP address no.
> open 192.168.1.201 10000 return
* Use the IP address
assigned to the projector
After the communication is established, type the password and the command for
controlling the projector and then enter “Enter” key.
The right table shows the typical command lists for controlling the our projector and
please consult your local dealer for further information of another commands.
Command list table
Command
C00
C01
C05
C06
C07
C08
C09
C0A
C0B
C0C
C0D
C0E
C1C
C1D
68
Function
Turn the projector on
Turn the projector off
Selects input1
Selects input2
Selects input3
Selects input4
Volume up
Volume down
Mute on
Mute off
Video mute on
Video mute off
Menu display on
menu display off
Chapter 7
Appendix:A
7
ENGLISH
Connection examples
Web browser setting
Technical data
Network Board
OWNER’S MANUAL
69
Chapter 7 Appendix
Examples of Connection
Peer-To-Peer connection
Connect the projector (PJ01) to the control computer (PC05) directly
Computer Name: PC05
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.5
: 255.255.255.0
:
:
Projector Name: PJ01
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 0.0.0.0
* UTP cross cable
Connect the projector (PJ01) to the control computer (PC05) via the hub.
Hub
Computer Name: PC05
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.5
: 255.255.255.0
:
:
Projector Name: PJ01
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 0.0.0.0
Computer Name: PC10
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.0.10
: 255.255.255.0
:
:
✐ When the projector is connected to the computer directly without hub, the UTP cross cable
should be used .
70
Examples of connection
The gateway (Router) installed in the network
Connect the projector (PJ01) to the control computer (PC05) via the gateway.
Theater
Computer Name
IP Address
Subnet Mask
Default Gateway
DNS
: PC205
: 192.168.200.5
: 255.255.255.0
: 192.168.200.1
: 192.168.201.1
Projector Name: PJ01
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.200.15
: 255.255.255.0
: 192.168.200.1
: 192.168.201.1
Hub
Network Group: 192.168.200.0
Gateway (Router)
To another network
IP Address : 192.168.200.1
IP Address : 192.168.100.1
IP Address : 192.168.10.1
Office
Hub
ENGLISH
Hub
Computer Name: PC05
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.10.5
: 255.255.255.0
: 192.168.10.1
: 192.168.201.1
Computer Name
IP Address
Subnet Mask
Default Gateway
DNS
: PC10
: 192.168.10.10
: 255.255.255.0
: 192.168.10.1
: 192.168.201.1
Computer Name
IP Address
Subnet Mask
Default Gateway
DNS
: PC51
: 192.168.10.51
: 255.255.255.0
: 192.168.10.1
: 192.168.201.1
Computer Name
IP Address
Subnet Mask
Default Gateway
DNS
: PC61
: 192.168.10.61
: 255.255.255.0
: 192.168.10.1
: 192.168.201.1
Network Group: 192.168.10.0
Network Board
OWNER’S MANUAL
71
Chapter 7 Appendix
Web browser setting
This product is designed enable the projector to be set up and controlled from an
Internet web browser. Depending on the preference settings of the web browser,
some control functions may not be available. Please make sure that the following
functions are set up properly in the web browser.
Active Script/JavaScript enable
There are some control items used with the JavaScript
function in the setting pages. If the web browser is set
not to use this JavaScript function, it may not control the
projector properly. In this case, the following warning
message will be displayed on the top of the page. To
enable the JavaScript, please see further instructions on
the next page.
Proxy setting
In some cases, your web browser is set up to use the proxy server for the internet or
intranet connection. In this case, when you install this product into the local network,
you should set up the proxy setting of web browser preference correctly. Especially
when connecting the projector and computer with a UTP cross cable directly, or
when the network does not provide the proxy server, make sure that “not use proxy
server” is set up in your web browser preference. To set up the proxy setting, please
see further instructions of item "Proxy setting" (☞ p.74).
✐ There are various ways to change your browser preferences depending on the version,
Windows, Macintosh or applications. Please see the setting instructions on next page for
example and also refer to on-line help of your web browser.
72
Web Browser Setting
Examples: OS/Browsers
Windows XP Professional
Internet Explorer v.6.0
ActiveScript setting
ENGLISH
Select the Internet Options menu from the Tool menu on the web browser and then
select Security tab and click Customize Level… button. On the security setting window, scroll down and find the Scripting item, make sure that “Enable” is selected in
item Active Scripting.
Network Board
OWNER’S MANUAL
73
Chapter 7 Appendix
Proxy setting
Select the Internet Options menu from the Tool menu on the web browser and then
select Connection tab and click LAN Settings button. Properly set up your web
browser's the proxy server settings according to the local area network environment
to which the projector is connected.
- Using proxy server
To use an external internet connection from the local area network, check the item
Use a proxy server and enter the proxy server address and port correctly in the proxy
settings window. For further instruction please consult your network administrator.
- Not using proxy server
Uncheck the item Use a proxy server.
If you connect the projector to the computer directly with UTP cross cable, this must
be unchecked.
To designate proxy settings that will not use
the proxy server when accessing the projector installed in the local area network, enter
the IP address or domain name here.
74
Web Browser Setting
Netscape Navigator v.7.0
JavaScript Setting
ENGLISH
Select the Preference menu from the Edit menu on the web browser and then select
the item Advanced/Scripts & Plugins in the Category column. Make sure that the
Enable JavaScript for Navigator is checked.
Network Board
OWNER’S MANUAL
75
Chapter 7 Appendix
Proxy setting
Select the Preference menu from the Edit menu on the web browser and then select
the item Advanced/Proxies in the Category column. Properly set up your web browser's the proxy server settings according to the local area network environment to
which the projector is connected.
- Using proxy server
When you use an external internet connection from the local area network, select the
item Manual proxy configuration. Enter the proxy server address and port number
correctly on the HTTP Proxy item. For further instruction please consult your network
administrator.
- Not using proxy server
Select the item Direct connection to the Internet in the proxy setting window.
If you connect the projector to the computer directly with UTP cross cable, this must
be selected.
To designate proxy settings that will not use
the proxy server when accessing the projector installed in the local area network, enter
the IP address or domain name here.
76
Web Browser Setting
Mac OS 8.6
Internet Explorer v.5.0
ActiveScript setting
ENGLISH
Select the Preference menu from the Edit menu on the web browser and then select
Web Content under the Web Browser heading the preference settings window. Make
sure that the Enable scripting is checked in the Active Content column.
Network Board
OWNER’S MANUAL
77
Chapter 7 Appendix
Proxy setting
Select the Preference menu from the Edit menu on the web browser and then select
Proxies under the Network heading the preference settings window. Properly set up
your web browser's the proxy server settings according to the local area network environment to which the projector is connected.
- Using proxy server
When you use an external Internet connection from the local area network, check the
item Web Proxy and enter the proxy server address correctly. To make advanced settings, press the Settings button to display the Web proxy settings window. For further instruction please consult your network administrator.
- Not using proxy server
Uncheck the item Web Proxy.
If you connect the projector to the computer directly with UTP cross cable, this must
be unchecked.
To designate proxy settings
that will not use the proxy server when accessing the projector installed in the local area
network, enter the IP address
or domain name here.
78
Web Browser Setting
Netscape Navigator v.4.7
JavaScript Setting
ENGLISH
Select the Preference menu from the Edit menu on the web browser and then select
the item Advanced in the Category column. Make sure that Enable JavaScript is
checked.
Network Board
OWNER’S MANUAL
79
Chapter 7 Appendix
Proxy setting
Select the Preference menu from the Edit menu on the web browser and then select
Proxies under the Advanced heading in the Category column. Properly set up your
web browser's the proxy server settings according to the local area network environment to which the projector is connected.
- Using proxy server
When you use an external Internet connection from the local area network, select
item Manual proxy configuration and press the Configure button. The proxy setting
window will appear. Enter the proxy server address and port number correctly on the
HTTP proxy item in the proxy settings window. For further instruction please consult
your network administrator.
- Not using proxy server
Select item Direct connection to the Internet in the proxy setting window.
If you connect the projector to the computer directly with UTP cross cable, this must
be selected.
To designate proxy settings that will not use
the proxy server when accessing the projector
installed in the local area network, enter the IP
address or domain name here.
80
Specifications
Product specification
Type ......................................Network Board
LAN interface ........................Applicant regulation
IEEE802.3 (10Base-T)
IEEE802.3u (100Base-TX)
Data transfer speed
10Mbps/100Mbps
Data transfer mode
Half duplex/Full duplex
Terminal
8-pin modular (RJ-45)
Network protocol
TCP/IP specification
TCP/IP
Serial interface
RS-232C
Baud rate
0.3/1.2/2.4/4.8/9.6/19.2/28.8/57.6/115.2 Kbps
Flow control
Hardware flow control (RTS/CTS, Xon/Xoff)
Parity check
Odd/Even
Terminal
D sub 9-pin Male
Power source ........................Supplied from the projector
Power consumption ..............3.0 watts
Dimensions (W x H x D)........5.39” x 1.18” x 4.33” (137 x 30 x 110mm)
Weight ..................................0.34 lbs (155 g)
Built-in battery ......................Lithium battery, Type CR2032, 3.0V
Operating temperature..........41˚F ~ 95 ˚F (5˚C ~ 35 ˚C)
Storage temperature ............14˚F ~ 140˚F (-10˚C ~ 60˚C)
ENGLISH
* The specifications are subject to change without notice.
Network Board
OWNER’S MANUAL
81
Chapter 7 Appendix
Port Specification
LAN port specification
8-pin modular connector (RJ-45)
12 3 4 5 6 7 8
pin No.
Signal
1
2
3
4
5
6
7
8
TX+
TXRD+
(not used)
(not used)
RD(not used)
(not used)
Function
Transfer data (+)
Transfer data (-)
Receive data (+)
Receive data (-)
Serial port specification
D sub 9-pin connector (RS-232C)
5
4
9
82
3
8
2
7
* It is possible to switch the polarity of the serial port
as shown in table below by switching the socket on
the network board. For further information, see
item "Serial Port Switching" (☞ p.65). At the factory
shipped setting, the socket is set to side A.
1
6
Pin No.
Socket
Side A
Signal Name
Side B
1
2
3
4
5
6
7
8
9
CD
RXD
TXD
DTR
Ground
DSR
RTS
CTS
-
TXD
RXD
Ground
-
- Explanation of signal names
Function
CD
RXD
TXD
DTR
DSR
RTS
CTS
-
Carrier detection
Receive data
Transfer data
Data terminal ready
Data set ready
Request to send
Clear to send
Not used
Appendix:B
ENGLISH
Q&A
Network Board
OWNER’S MANUAL
83
Chapter 7 Appendix
Q&A
Installation/Access
Q Why doesn’t the setting page appear in my web browser?
A
Following causes are possible. Please check them.
1. The projector is not connected to the network.
Check LED indicators status (☞ p.13).
- Check the connection of LAN cable if the LINK indicator does not illuminate
orange.
- Check the network configuration of the projector if ACT indicator does not
illuminate green.
2. Function “Network” in the projector is not set to“ON”.
Set up by using the projector’s on-screen menu (☞ p.16, 20).
3. Wrong network configuration of the projector
Check the network configuration of the projector by using the projector’s onscreen menu (☞ p.16, 20).
4. Wrong network configuration of the computer.
Check the network configuration of the computer.
5. The Network Board is used with the default setting (☞ p.16, 20).
6. The proxy setting of the web browser is not set correctly (☞ p.72).
7. The computer does not provide TCP/IP protocol.
Q No setting page in my web browser? Is the problem in the network or
in the projector? I would like to find out the problem whether it is in
the network or in the projector
A
Check it by the following steps
1. Disconnect the projector from the network and connect the projector and
computer with the UTP cross cable directly.
2. Change network configuration of the computer and projector as shown in the
example below.
(Projector setting)
IP Address
Subnet Mask
Default gateway
DNS
84
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 0.0.0.0
(Computer setting)
IP Address
Subnet Mask
Default gateway
DNS
: 192.168.0.5
: 255.255.255.0
: (blank)
: (blank)
Q&A
3. Enter the projector’s IP address [192.168.0.2] at the “Address” column on the
Web browser. [Note] Make sure that the proxy setting of your web browser is
set to “Not use a proxy server” (☞ p.72).
4. If the login page appears, this product is operating properly. The problems
may be in the network configuration of the computer or in the network.
Please try to set up the network by following chapter “Network configuration” (☞ p.16, 20).
If the login page does not appear, please check for proper mounting of this
product onto the projector by referring to chapter 2 “Installation” (☞ p.11).
Q How can I restrict access from the computer.
A
1. Please use the password authentication function on the login page (☞ p.30).
2. Please use the IP filtering function provided with the gateway (router) to
restrict the accessing from the computer. For further information please consult your network administrator.
Q Can I access the projector installed on the company’s local area netA
There are some ways to access to the projector in the LAN, but you must consult your network administrator.
☛ Use of modem
(Connect to the company’s network from your home or some other places
by using modem.)
☛ Use of private line
(Connect to the company’s network from the branch office or maintenance
office by using private line.)
☛ Use of internet
(Connect to the company’s network from your home, branch office or some
other places by using the internet.)
ENGLISH
work from a remote location?
Q We use the DHCP/BOOTP server to assign the IP address. Is it possible to use the Network Board in this network environment?
A
Possible. As the Network Board does not support the DHCP/BOOTP server, the
fixed IP address must be configured manually. Please consult your network
administrator (☞ p.23).
Network Board
OWNER’S MANUAL
85
Chapter 7 Appendix
Q How can I install several projectors equipped with the Network
Board?
A
Install and configure network one by one to avoid the IP address collision each
other (☞ p.23).
To configure the IP address please see chapter “Network configuration” (☞
p.16. p.20)
Q How many projectors can I control with multi-control function?
A
It has been designed to control up to 100 sets but it depends on the network
environment.
Password/Login
Q What should I do when I forget the password?
A
Select the "Network PIN code" menu or the "Password" menu on the projector's
on-screen menu. The current password will appear on the screen (☞ p.18, 22).
Q Can I register the setting page as a web browser “Favorites” or
“Bookmarks”?
A
86
Please add the “Login” page to your “Favorites” or “Bookmarks”. Do not add
the specified setting page because it will not be able to perform the password
authentication correctly.
Q&A
Operation
Q Why can't I change the controls in the setting page with web browser?
A
Please make sure the projector is turned on. If it is in the standby mode, the
setting is not effective to the projector. To control the projector with a web
browser, the projector must be in the powered-on condition. Also, projectors
registered for multi-control cannot have any controls changed if they are in
standby mode. But timer and clock settings are always effective, even for projectors in standby mode.
Q Why does it sometimes take a lot of time to complete the page display?
A
The display speed of the page depends on the network environment in which
both the projector and computer are placed. It may take much time to complete
the page display if network traffic is heavy. Please consult your network administrator. By changing the preference of your web browser to “not show pictures”, you may have page display more quickly at the heavy network traffic.
Please see the browser’s on-line help for further information. Also you can
select the Text mode for displaying pages quickly (☞ p.26).
Q I use many of the projectors in the network. How can I use names of
A
You can manage the projectors with nicknames instead of the IP address.
Please see chapter “Controlling the Multi-Projectors” for further information (☞
p.55).
By registering the projector name and IP address with the DNS server, it can be
accessed with the nickname from the any computer referred to the DNS server. Please consult your network administrator (☞ p.31, 57).
Q How many numbers of the E-mail addresses can I register in the E-
ENGLISH
the projectors to recognize each projector instead of IP addresses?
mail setting page.
A
You can register up to 10 addresses.
Network Board
OWNER’S MANUAL
87
Chapter 7 Appendix
Q Why am I not receiving E-mail alert messages?
A
Make sure that the registered E-mail address and SMTP server address are correct. If the SMTP server is located in your LAN (Local Area network), the
address should be set to the SMTP server in your LAN. The SMTP server located outside of your LAN may not be available for security reason. For further
information please contact your network administrator (☞ p.32).
It may be required for the authentication depending on the SMTP server.
This product does not support this kind of SMTP server.
Others
Q Can I develop a driver to control external serial equipment?
A
This product does not provide any driver software. To control the external
equipment connected to the extra serial port, it should be required to clarify the
commands and communication condition defined by each equipment. If they
are clarified, it can be controlled by using the Telnet application installed on your
computer. Please see item “Use of telnet” (☞ p.66).
Q Can I control the projector by using the telnet application?
A
88
Possible. Please refer to item “Control the projector with telnet“ (☞ p.68).
Q&A
Q Can I update the firmware of the Network Board.
It is possible to update the firmware
through the network. It is required
to have a special tool for the updating. For further information please
consult your local dealer. The version number of the firmware is indicated on the lower part of the“Initial
Setting” page.
ENGLISH
A
Network Board
OWNER’S MANUAL
89
Chapter 7 Appendix
Q What are the rules for IP address assignment?
A
If the network is constructed with TCP/IP protocol, a unique IP address is
required for each piece of network equipment. The following are basic rules of
the assignment.
Rule1
Do not configure the same IP address to the network equipment in the
same network group. Each piece of equipment must be assigned a
unique IP address.
If the IP address is set [192.168.x.x], the Subnet Mask should be set
[255.255.255.0] for example.
Rule2
The start address [xxx.xxx.xxx.0] and the last address [xxx.xxx.xxx.255]
of the IP address must not be assigned to any other equipment. These
address numbers are reserved.
Rule3
The IP address must correlate to a network number. If network numbers
are different between the equipment, they cannot establish communications each other. In this case, the router is placed in the networks to
make the routing.
Q What is the MAC address assigned to the Network Board?
A
The MAC address is indicated on the printed board as the below.
MAC address
90
ENGLISH
Q&A
Network Board
OWNER’S MANUAL
91
Network Board Owner’s Manual
IDRMD (built in KJ5AL) (b)
SANYO Electric Co., Ltd.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising