Sanyo | PDA POA-PN02C | User's Manual | Sanyo PDA POA-PN02C User's Manual

Sanyo PDA POA-PN02C User's Manual
POA-PN02C
DC OUT CONTROL PORT VIDEO IN
K
LIN
ACT
PJ-Net Organizer plus C
OWNER'S MANUAL
PLV-80/75 Series
Compliance
Federal Communication Commission Notice
This equipment has been tested and found to comply
SANYO
POA-PN02C
with the limits for a Class B digital device, pursuant to
Tested To Comply
part 15 of the FCC Rules. These limits are designed to
With FCC Standards
provide reasonable protection against harmful interference in a residential installation. This equipment generFOR HOME OR OFFICE USE
ates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-C
onnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-C
onsult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of
FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in
the instructions. If such changes or modifications should be made, you could be required
to stop operation of the equipment.
Model Numbers
: POA-PN02C
Trade Name
Responsible party
Address
Telephone No.
: Sanyo
: SANYO FISHER COMPANY
: 21605 Plummer Street, Chatsworth, California 91311
: (818)998-7322
Compliance and Caution
caution ON Use in network
- When you receive an alert e-mail from the projector, you must check the projector
immediately. Fire or accident may result if the projector is used in an abnormal
condition.
- When you install the projector at remote location and use it through the network, you
must perform the safety inspections periodically. In this case you must pay attention to
the change of environment in which you installed the projector. It may cause fire or an
accident depending on the change of environment.
caution
SANYO Electric Co., Ltd. assumes no responsibility for the loss or damage of data or
damage of the computer caused by usung this product.
The CE Mark is a Directive conformity mark of the European Community (EC).
NOTES ON Lithium Battery (CALIFORNIA USA ONLY)
This product uses a Lithium Battery which contains Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
Notas acerca de pilas de litio (SOLO PARA CALIFORNIA, EE.UU.)
Este producto usa una pila de litio que contiene el material perclorato – puede ser necesario una manipulación especial.
Consulte la página www.dtsc.ca.gov/hazardouswaste/perchlorate
Contents
Compliance...........................................................................................................................................................................2
Federal Communication Commission Notice.......................................................................................2
Chapter 1 Preparation.................................................................................................7
Features...................................................................................................................................................................................8
Operating environment of PJ-Net Organizer................................................................................................ 10
Before use............................................................................................................................................................................ 11
Chapter 2 Installation............................................................................................... 15
Flow of installation......................................................................................................................................................... 16
[1] Name and function of each part................................................................................................................... 17
[2] Installation and network configuration..................................................................................................... 18
Mounting................................................................................................................................................................... 18
Connection of LAN cable................................................................................................................................ 19
Network configuration......................................................................................................................................20
Network PIN code setting...............................................................................................................................22
How to enter the numbers with the screen 10-key pallet..........................................................23
Notice about system construction............................................................................................................24
Chapter 3 Basic Setting and Operation.............................................................. 25
Login the setting page of the projector..........................................................................................................26
1 Enter the IP address.........................................................................................................................................26
2 Select a display mode and login.............................................................................................................26
3 Display of main setting page....................................................................................................................27
How to use the setting page..................................................................................................................................28
Initial setting......................................................................................................................................................................30
Network PIN code setting............................................................................................................................... 31
PJLink and password setting......................................................................................................................... 31
Date and time setting........................................................................................................................................32
Network configuration................................................................................................................................................33
E-mail setting....................................................................................................................................................................34
Examples: Type and contents of alert mail...........................................................................................36
SNMP setting.....................................................................................................................................................................38
Chapter 4 Controlling the Projector.................................................................... 41
Power control and status check............................................................................................................................42
Controls.................................................................................................................................................................................44
Input..............................................................................................................................................................................44
System..........................................................................................................................................................................45
Image adjustment...............................................................................................................................................46
Sound . ........................................................................................................................................................................47
Menu ...........................................................................................................................................................................47
PC adjustment..................................................................................................................................................................48
Setting up the projector............................................................................................................................................49
Save the controls and settings............................................................................................................................... 51
Store/free the settings....................................................................................................................................... 51
Check the saved items.......................................................................................................................................52
Load a control set.................................................................................................................................................52
Timer setting.....................................................................................................................................................................53
How to set the timer...........................................................................................................................................53
Check the timer events.....................................................................................................................................54
Change the event mode..................................................................................................................................54
Contents
Projector information...................................................................................................................................................56
Multi-control......................................................................................................................................................................58
Controlling and setting the multi-projectors.....................................................................................58
Start/stop the multi control...........................................................................................................................59
Register the projector........................................................................................................................................60
Confirmation of registered projector.......................................................................................................60
Change the mode of the registered projector.................................................................................. 61
Status............................................................................................................................................................................ 61
Check & Change page in the light mode..............................................................................................62
Controlling all together.....................................................................................................................................62
Setting all together..............................................................................................................................................62
Chapter 5 Use of Serial Port . ................................................................................. 63
Serial port setting...........................................................................................................................................................64
Control examples...........................................................................................................................................................66
Use of telnet.......................................................................................................................................................................68
Chapter 6 Appendix ................................................................................................. 71
ENGLISH
Examples of connection............................................................................................................................................72
Web browser setting.................................................................................................................................................... 74
Examples: OS/Browsers..............................................................................................................................................75
Product specification...................................................................................................................................................79
Port specification............................................................................................................................................................80
Q&A.........................................................................................................................................................................................81
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
Chapter 1
Preparation
1
ENGLISH
Describes features and operating environment of this product.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
Chapter 1 Preparation
Features
Web Management function (+p.25)
With this func tion, you can
monitor projector functions
such as power status, lamp
s t at us , inp u t m o d e, si gnal
condition, lamp-use time, etc.
through the network by using
the web browser installed on
your computer.
PC1
PC2
PC3
PC4
PJ2
PJ1
PC6
PC5
Turn ON PJ2
E-Mail Alert function (+p.34)
The projector (Network Unit)
sends messages to the registered e-mail addresses when
a lamp abnormality or power
failure occurs with the projector. This message describes
how to solve the cause of the
problems. You can take efficient
action for quick recovery.
PJ Camera Viewer function (refer to the separated
booklet)
To send the information of the
projector to the SNMP manager.
Enables you to manage the projector condition with the supplied SNMP manager software.
PC2
PC3
PC4
PJ2
PC6
You’ve got
Mail.
PJ1
PJ2
JPEG
PJ3
JPEG
PJ4
JPEG
JPEG
PC6
PC5
PC4
JPEG
PJ1
PJ2
PJ3
PJ4
Trap
PC6
PC5
PC4
You received
a Trap.
Trap
PJ1
PC5
By using the supplied camera,
PJ Camera Viewer takes pictures
of the projected images of the
projector located on the remote
places, and stores pictures into
your computer via the network.
SNMP Agent function
(+p.38)
PC1
SNMP Manager
Features
Multi-control function (+p.58)
PJ1
PJ2
PJ3
A single computer can control and set up the multiple
projectors at the same time.
PJ4
PC6
PC5
Automatic On/Off using
Clock function (+p.53)
PC4
Select Input2 for
PJ1 to PJ4.
I am ready to turn ON,
and select Input 3 (Video)
Automatically turn on or off the
projectors at specified date/day
and time by using the clock function.
Now it’s 11:30
SNMP Manager function (refer to the separated booklet)
A f un c t i o n to mana g e th e
condition of projectors in the
network by using the SNMP
protocol. The managing computer ne e ds to provide an
SNMP managing software. Refer
to the owner's manual of the
"PJ Network Manager" supplied
separately for further details.
PJ1
PJ2
PJ3
PJ4
Trap
PC6
PC5
PC4
You received
a Trap.
Trap
SNMP Manager
Control port ready for external equipment (+p.63)
This product provides a serial port for controlling external equipment. By connecting
the equipment to the serial port, it can be
controlled by a computer via the network.
* This product does not provide the interface
driver software to control external equipment.
ENGLISH
PJ2
DVD Player
PC3
PC5
Playback DVD
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
Operating Environment
Chapter 1 Preparation
Operating environment of PJ-Net Organizer
To perform the managing and setting of the projector by using this product, the environment described below is required.
Standard mode
Operating System
Windows 98, Windows Me, Windows NT4.0SP6
Windows 2000, Windows XP
Computer environment
Recommended CPU
Higher than Pentium III 900MHz
Memory
6 4MB (Minimum)/ 128MB or more (Recommended)
128MB or more for Windows XP
HDD free area
100MB or more
Drive equipment
CD-ROM drive
Display setting of
computer
S upport one of following resolutions;
VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x 768) Number of colors: Either of 16 bit (65,536 color 24/32 bit (16,77 million colors))
Network card
The computer must provide a 10Base-T or 100Base-TX network
card.
Web Browser*
Internet Explorer version 5.0, 5.5 or 6.0
Netscape Navigator version 6.2, 7.0 or 7.1
* Used to control and set up the projector. The layout of pages in
the browser may slightly differ from each type of application or
operating system you use.
Plug-Ins
Adobe Flash Player version 6,0,79,0 (6.0r79) or later
Internet Mailer*
- Microsoft Outlook
- Microsoft Outlook Express
- Netscape Mail
* Required the internet e-mail application software to receive an
e-mail alert sent from this product. If you do not use the function
E-mail Alert, this application is not required.
This product has been designed for the projectors listed below.
PLV-80/75 series
* For the operating environment of PJ Network Manager and PJ Camera Viewer,
refer to each owner's manual in the document CD-ROM.
PDA restriction
The PDA can be used for the Light mode*1 only. The operating system of the PDA is
PocketPC2002 or higher. The version of the Adobe Flash Player is 6,0,81,0 or higher.
10
*1 The "Light Mode" and "Standard Mode" will be explained on item "Display Mode" (☞ p.26-28)
The limitation*1 of connection between this product and hub or computer
Suitable LAN cables are limited by length and type as follows;
Connection
Type of usable LAN cable
Maximum length
Network Unit - Hub
UTP Straight Cable with category 3 or 5 *
100m
Network Unit - Computer
UTP Cross Cable with category 3 or 5*2
100m
2
*1 There
may be other limitations depending on your network environment or LAN specification.
Please consult your network administrator for further details.
*2 C
ategory of LAN cable indicates the cable quality. Normally, a cable with category 3 or 5 is used
for 10Base-T network, and a cable with category 5 is used for 100Base-TX network.
Before use
Package contains
The package contains following items. Check each item as you unpack the package. If you
have any of the following items missing, contact the sales dealer.
K
❑ Network unit
1 piece
❑ Quick Setup Guide
English/Japanese
1 piece
❑ Software CD-ROM
Network Viewer & Capture 3 software*
PJ Network Manager software
1 piece
ACT
Quick Setup
Guide
* This software does not support PLV-80/75 series projectors.
❑ Document CD-ROM
PJ-Net Organizer Owner's Manual
PJ Network Manager Owner's manual
PJ Camera Viewer Owner's manual
1 piece
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
LIN
11
Before use
Chapter 1 Preparation
Following contents are required to use the PJ Camera Viewer function.
❑ Network Camera
1 piece
Camera Packaging box
❑ Software CD-ROM
PJ Camera Viewer software
Network Viewer & Capture 3 software *
1 piece
* PLV-80/75 series projector does not support this software.
Envelope
❑ Camera mounting tool set
Hook and loop fastener (big)
Hook and loop fastener (small)
Cable fixer
Ferrite core
Double-sided adhesive tape*
Safety rope*
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
* For use of the double-sided adhesive tape and the safety
rope, refer to the caution cards.
12
Notice
Expression/Abbreviation
The word "projector" found in this manual means "projector provided with Network unit"
unless otherwise noted.
The OS of the computer and the Web browser described in this manual is Windows XP
Professional and Internet Explorer 6.0. In case of another OS or Web browser, some instruction procedures may differ from the actual operation depending on your computer environment.
Use of this manual
This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer to the respective booklet.
Trademarks
Ethernet is a registered trademark of Xerox Corporation. Microsoft, Windows, Windows
NT are registered trademarks of Microsoft Corporation. Internet Explorer is a registered
trademark of Microsoft Corporation. Netscape Navigator and Netscape Communicator are
trademarks or registered trademarks of Netscape Communications Corporation. JavaScript
is a registered trademark of Sun Microsystems, Inc. PJLink is a registered trademark of
JBMIA (Japan Business Machine and Information System Industries Association).
Other product or brand names in this manual are registered trademarks or trademarks of
their respective owners.
ENGLISH
* Unauthorized use of a part or whole of the contents in this manual is prohibited.
* The contents of this manual are subject to change without notice.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
13
Chapter 1 Preparation
14
Chapter 2
Installation
2
ENGLISH
Describes how to install the network unit and software, and configure the network.
15
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
15
Chapter 2 Installation
Flow of installation
The following are instructions for attaching this product to the projector and connecting it
to the network. Please review the entire procedure to become familiar with it.
1 Function of the network unit (☞ p.17)
Explains the name and functions of each part of the network unit.
2 Installation and network configuration (☞ p.18-24)
1 Mount this product onto the projector.
2 Connect the LAN cable and join it to the network.
3 Configure the network of the network unit.
4 Set the Network PIN code.
Set up is complete
The preparation is completed to control the projector connected to the network. At next
step, set up and control the projector via the network by using the web browser installed
on your computer. Please see chapter 3 "Basic setting and operation". (☞ p.25)
For the installing the camera and PJ Camera Viewer and operating instructions,
refer to the separated owner's manual of PJ Camera Viewer.
16
Name and function of each part
[1] Name and function of each part
(Top View)
POWER indicator
This lights up red when the network
function is set ON in the projector
menu.
DC OUT CONTROL PORT VIDEO IN
Mounting screws
Mount by using a coin etc. (☞ p.18)
K
LIN
ACT
ACT indicator
This turns on and off with green when
sending or receiving of data
LINK indicator
This lights up red when the network unit is
connected to the network correctly.
(Bottom View)
Connector plug
Connecting to the terminal on the projector. (☞ p.18)
Power jack for Camera
Used to connect the camera power cable
(refer to separated owner's manual)
Used to control the external equipment
via the network. (☞ p.63)
Video input jack for Camera
Used to connect the camera video cable
(refer to separated owner's manual)
LAN port
Connecting the LAN cable. (☞ p.19)
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
DC OUT CONTROL PORT
VIDEO IN
Serial port
17
Chapter 2 Installation
[2] Installation and network configuration
Mounting
1 Disconnect the AC plug from the projector.
2 R emove the connector cover and screw
Connector cover
covers (2 pieces) from the projector and
insert plug on this product to the option
connector.
Screw cover
3 T ighten two screws by using a coin
etc.
!
18
Caution
✐ AC cord must be disconnected when mounting or removing this product otherwise it may damage the product.
✐ Do not install multiple network units into a projector otherwise it may damage the product.
✐ Connect the AC cord after connecting the LAN cable and computer.
Installation and network configuration
Connection of LAN cable
To connect to the network, it is required to use the UTP (Unshielded Twisted Pair) straight cable
with RJ-45 plug. There are two different types of cables depending on whether the network is
constructed with 10Base-T or 100Base-TX. Prepare the Hub (10Base-T or 100Base-TX) to distribute the network cable if required.
1 Disconnect the AC plug from the projector.
2 Connect the UTP straight cable to the LAN
port on the network unit.
3 Connect the UTP straight cable to the hub.
Hub
(10Base-T, 100Base-TX)
Projector
✐ Use the UTP cross cable when you connect the computer and projector directly not using the
hub.
✐ When you connect the projector into the 10Base-T network, use cable with category 3 or 5. When
you connect the projector into the 100Base-TX network, use cable with category 5.
✐ The length of cable between hub and projector should be less than 100m.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
UTP straight cable
19
Chapter 2 Installation
Network configuration
Confirmation of the network menu
When installing this product to the projector, the network on-screen menu items for this
product are activated automatically. If not activated, the product may not have been
installed correctly. Please check item "Mounting" (☞ p.18).
Configure the network
Before performing the network configuration, prepare network address numbers (IP
Address, Subnet Mask, Default Gateway, DNS) assigned to the projector. Ask your network
administrator for the network address.
For example, the case where the following network address is set up is explained.
IP Address
Subnet Mask
Default Gateway DNS
: 192.168.1.201
: 255.255.255.0
: 192.168.1.1
: 0.0.0.0
The default network configuration is set as follows.
IP Address
Subnet Mask
Default Gateway DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 0.0.0.0
DC OUT CONTROL PORT VIDEO IN
LIN
K
ACT
1 Selection of network menu
Turn on the projector and display the menu on the screen. Select network icon from the
main menu and then press SELECT button once. Check that the mode is "On". If not,
change mode to "On" using the point buttons (7,8).
Select "On" or "Off"
with 7,8 button
20
✐ The network unit begins restarting each time the mode is set "On".
Network icon
Installation and network configuration
2 Configuration for IP Address/ Sub net/ Gateway*1/DNS*2
Press SELECT button again. The following network setting pallet appears on the screen.
Enter the specified network addresses.
The red frame moves
sequentially left or right
with 7 8 button.
The number up or down
with d e button.
How to enter the numbers
There are 2 ways to enter the numbers, one is by using the point buttons (d e ) on
the remote control or on the projector, the other is by using the screen 10-key pallet by
which the numbers can be entered directory. For further information see "How to enter
the numbers with the screen 10-key pallet" (☞ p.23).
3 Fixing the network configuration
After completing the entering of address, select "SET" and
press SELECT button. The network unit starts re-booting
and displays message "Please wait..." on the screen until
the re-booting is complete. Do not disconnect the AC
cord during this period.
Completing of installation
Now the installation is complete. The IP address of this projector is set to "192.168.1.201".
Item
Description
✐ Refer to the projector's owner's manual for operation of the projector.
*1 In
the network environments not using a Gateway or Router, the Gateway address should be set to [0.0.0.0].
*2 If you do not use the functions E-mail or DNS server, it is also set [0.0.0.0] for the DNS address.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
IP address..............Sets IP address of the projector
Sub net....................Sets Subnet mask. Normally sets 255.255.255.0
Gateway*1.............Sets IP address of the default gateway (Router)
DNS*2........................Sets IP address of the DNS server. Must be set when using the e-mail function
21
Chapter 2 Installation
Network PIN code setting
The Network PIN code can be set to restrict access to the setting page of the projector
using the web browser.
✐ Default Network PIN code [0000] means no Network PIN code is set.
1 Displaying Network PIN code menu
Select network menu and then select "Network PIN code" sub menu. Press SELECT button twice to display the Network PIN code entry pallet.
*The number on the pallet is the current Network PIN code.
Network PIN Code
2 Entering the Network PIN code
The red frame moves
sequentially left or right
with 7 8 button.
The number up or down
with d e button.
To enter the Network PIN code, use point buttons
(▲,▼,7,8) on the projector or the remote control.
3 Fixing the Network PIN code
After entering a 4-digit number, select "SET" by
using point buttons (7,8) and then press SELECT
button.
✐ The screen 10-key pallet can be used for entering the Network PIN code. See item "How to enter
the numbers with the screen 10-key pallet" (+. 23)
22
✐ It is recommended to set up the Network PIN code when you connect the projector to the network. This setting is carried out through the projector’s menu and also it can be set through the
network using the web browser. For further information, refer to item "Initial setting/Network PIN
code setting" (☞ p.30-31).
✐ Valid characters for the Network PIN code are only numbers 0 to 9. The number "0000" means no
Network PIN code is set.
✐ This Network PIN code is not to restrict the use of the projector. This Network PIN code is to set
the security against the use of the projector through the network.
Installation and network configuration
How to enter the numbers with the screen 10-key pallet
1 Select a column with a red frame by using the point buttons 7 8 .
2 Press SELECT button. The screen 10-key pallet appears on the screen.
3 By using the point buttons (d e 7 8), select numbers 0 to 9 and press SELECT button. By
repeating the above to enter the complete number on the column.
*To change the number in a column, select “C” and press SELECT button to clear the number in
the column and then enter the number again.
4 After entering the number in the column, select a move key (7 8 e d) located on the lower
part of the pallet by using the point buttons and press SELECT button repeatedly to move
the red frame.
5 Repeat steps 3 to 4 for entering all the network address.
6 After finishing, select "Exit" and press SELECT button. The 10-key pallet disappears on the
screen.
10-key pallet
ENGLISH
Exit
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
23
Chapter 2 Installation
Notice about system construction
For installation of multiple projectors into the same network with network
unit.
Do not install multiple projectors with network units that have their default network settings to the same network. The use of the network units which have the default IP address
set to the same network settings will cause IP addresses to collide and create a malfunction. When you install multiple projectors into the same network, configure the network
with the following steps.
1. Change the IP address from the default IP address. To change the IP address, use the
network setting menu on the projector. Please see item "Network configuration" for further information (☞ p.20).
2. Make sure that there is no network equipment set with the same IP address in the network before connecting to the network.
3. When installing other projectors, follow the above steps to change the IP address and
connect to the network.
In case of installing the projector with network unit into the network constructed with the DHCP/BOOTP server.
This network unit does not support the DHCP/BOOTP server. The static IP address must be
manually configured. To use this product in this network environment, set it up so that the
DHCP/BOOTP server does not assign the IP address configured to this product for another
device on the network. Please consult your network administrator for further information.
24
Chapter 3
Basic Setting and Operation
3
ENGLISH
Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and
projector is connected to the network and the network address is
properly configured.
25
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
25
Chapter 3 Basic Setting and Operation
Login the setting page of the projector
1 Enter the IP address
Launch the web browser installed in your
computer, enter the IP address into the
"Address" on the browser and then press
"Enter" key.
Enter the address (192.168.1.201) that you
configured in item "Network configuration" (☞ p.20). The default IP address is [192.168.0.2].
2 Select a display mode and login
This product provides 2 types of control mode, Standard Mode and Light Mode as the
below. Select a proper mode to match your PC and network environment by clicking
on the text link.
STANDARD MODEFor computer display, displays
graphical menus and settings. This
mode is recommended for standard
use.
LIGHT MODEDisplays with 200 x 300 dots. This
mode is optimized for use of the
handheld computer, PDA, etc. It is
also convenient if the network traffic is heavy. (This mode has some
limitations on the multi-control
function.)
If the setting page has set the password, the
authentication window will appear. In this case type
"user" onto the User Name text area and the login
Network PIN code onto the Password text area and
then click OK button.
* The entering User Name must be "user" and it can not be
changed.
[Note]
When accessing the projector for the first time or the
Network PIN code "0000" is set, the auto-login will be performed and the next main setting page is displayed.
26
Login the setting page of the projector
3 Display of main setting page
The following main setting page will be displayed according to your display mode
selection. Perform various kinds of settings through this page. Click on the menus to display the control and setting pages.
z Main setting page in the Standard Mode display
Clock display
Display on or off by
clicking text ON or
OFF
Sub menu tab
Switches the sub
menu tab.
Page numbers
Switches the pages
by clicking the
number's tab.
Main menu
For selection of control and
setting items of the projector.
Setting page
Displays the control and
setting items according to
the selected menu.
Returns to Display
Mode selection
page (☞ p.26)
✐T
his Standard mode display is mainly used through this manual for the setting and
control description.
✐If your computer does not have the
ENGLISH
Macromedia Flash Player version 6 or later,
follow to the message on the control page
to install the Macromedia Flash Player. For
further product information or installing,
see the Adobe homepage.
http://www.adobe.com
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
27
Chapter 3 Basic Setting and Operation
x Main setting page in the Light Mode display
Sub menu tab
Page numbers
Returns to the display mode selection page.
Main menu
Setting page
Returns to main menu
✐ T he blank page appears if your PDA does not provide a
Macromedia Flash Player. You need to install the Macromedia
Flash Player. (☞p.27)
How to use the setting page
To control and set up the projector, use the setting menus on the web browser. Describes the
basic operation and procedures commonly used on this manual.
Example of the Setting Page
The setting pallet appears when clicking the item.
Change the value by clicking s or t button, or type
the number onto the text box directory and then click
Set button.
* Each item has a valid setting range respectively.
Setting Pallet
✐ The value in the text box indicates current value.
✐Each item has a valid setting range. The setting value exceeding this becomes invalid. Some con-
28
trol items can not be used depending on the selecting input mode or functions of the projector
you use. In this case, the values of those items are indicated with "---".
How to use the setting page
Type of the setting pallet
Text box setting
Enter a number or text and
then click Set button.
or
Change a value with s or t
button and then click Set button.
The value changes quickly
when keeping pressing s or
t button.
Pull-down menu setting
Select an item with pull-down
menu button and then click
Set button.
or
Select an item by clicking s
or t button.
Radio button setting
Select an item by selecting a
radio button
Check box setting
ENGLISH
Select items by ticking on
check boxes.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
29
Chapter 3 Basic Setting and Operation
Initial setting
After installing this product to the projector, perform the following basic
initial setting.
Click Initial Setting on the main menu to display the initial setting page.
There are two sub menus, Initial setting and Serial Port setting sub menu. Serial Port setting page is used for controlling the external equipment through the serial port. For further description of setting and operation, refer to chapter 5 "Use of Serial Port" (+p.63)
The model name of the projector on which this product is mounted is displayed on the
page.
Item
Description
Language...............Switches display language on the setting page.
English or Japanese.
Model name........Indicates the model name of the projector provided with the network unit
Network PIN code............Sets the Network PIN code to login the setting
page (+p.31)
PJLink........................Switches PJLink password authentication on or off
(+p.31)
Password................Password for PJLink function
Temperature........Switches display temperature unit Centigrade or
Fahrenheit
!
Caution
Use of Battery
30
This product provides a lithium battery. When the battery runs down, the clock and timer functions
do not operate properly. Contact your local dealer for the replacement of battery. The replacement
must be carried out by a qualified service personnel.
Initial setting
Network PIN code setting
This is to set the Network PIN code to restrict the access from
an unauthorized person through the network.
Enter a 4-digit number as the Network PIN code onto the text
box and click Set button.
The network unit begins restarting and it takes about 20 seconds. Close (Quit) the web browser and access to the login
page again in 20 seconds. This is to perform the login authentication firmly.
The default Network PIN code [0000] means no Network PIN code is set.
W
hen you connect the projector with this product to the network, it is recommended to set a
new Network PIN code. Only a four-digit number is valid for the Network PIN code.
✐ If you forget the Network PIN code to the projector, you can check it by selecting "Network PIN
code" sub menu from "Network" menu on the projector. For further information, please see item
"Network PIN code setting" (+p. 22).
✐
PJLink and password setting
This is to set the PJLink password authentication on or off. If set
"On" with the PJLink pull-down menu, the password must be
required. Enter a password* onto the text box and click Set
button.
1 to 32 alphanumeric characters can be used for the password.
What's PJLink?
The projectors equipped with PJLink function can be used together on the same network,
regardless of model or brand, for centralized control and monitoring. This standard was
established by the Japan Business Machine and Information System Industries Association
(JBMIA).
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
✐
31
Chapter 3 Basic Setting and Operation
Item
Description
Time setting.........When clicking AUTO button, the date and time
set on your computer are set to the network unit
Current time........Indicates current date and time set on the network unit
Date...........................Sets date in manual
Time...........................Sets time in manual
Date and time setting
Auto setting
Click AUTO button on the page, the date and time set on your computer are set to the
network unit.
Note:
Confirm that your computer has a correct clock time before performing the auto time setting.
Manual setting
Click item Date or Time and enter date or time on the input box with adequate format.
Date is in year/month/day format.
ex. 2006/04/25
Time is in 24-hour:minute format.
ex. 18:30
32
Network configuration
Network configuration
Click Network on the main menu. The following setting page is displayed.
The IP Address, Subnet Mask, Default Gateway, DNS (Domain Name Server)
and projector name are set up on this Setting sub menu.
The IP address and Subnet Mask have been configured already in chapter "Installation".
If you want to change them or configure default gateway or DNS, perform them in this
page. If you change them, the network unit begins restarting and it takes about 20 seconds. Close (Quit) the web browser and access to the login page again in 20 seconds.
Item
Description
*1 Set [0.0.0.0] if the network does not provide the gateway (router).
*2 Set [0.0.0.0] if you do not use the function E-Mail alert.
*3 If you use the DNS server, register the host name registered to the DNS server as a projector
name. You can access with this projector name from any computers in your network. If you do not
use the DNS server, access with the assigned IP address to the projector.
* All the network setting will reset to the default when setting [0.0.0.0] of the IP Address.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
IP address..............Sets IP address of the projector
Subnet mask........Sets Subnet mask. Normally sets 255.255.255.0
Default gateway*1......Sets IP address of the default gateway (Router)
DNS*2........................Sets IP address of the DNS server. Must be set
when using the e-mail function
PJ name*3. .............Sets name of the projector. (64 characters maximum)
✐Y
ou must use the number specified by your administrator. The
address must be entered as a group with four numbers split by
a dot like [192.168.001.101].
33
Chapter 3 Basic Setting and Operation
E-mail setting
This product has an E-mail function which can send an alert message
to users or an administrator if it detects an abnormality on the projector
or run out of the life span of the lamp. Click E-mail setting on the main
menu and follow the below steps.
Item
Description
SMTP server*1.....Sets server name or IP address of the SMTP server
Administrator
address....................Sets e-mail address of administrator
Add e-mail
address....................Sets e-mail address of the user to send mail when
the projector has an abnormality.
1 Setting SMTP server and administrator address
Set the server name or IP address of the SMTP server*1 and administrator address. The
administrator address is set to "Reply-To" address of the message sent from the projector.
*1 T he SMTP server is a server for sending E-Mail. Please contact your network administrator to
have this SMTP server address.
✐ If the network unit sends an alert message due to the abnormality on the projector but the SMTP
server is down in some other reason, the message will not be sent. In this case, the message
"Unable to connect to server." will be displayed on the setting page. To clear this message, set up
SMTP server address again.
✐ To use the E-Mail function, it must be set the DNS address on the Network setting page correctly.
34
✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your network environment.
E-mail setting
2 R egistering and deleting E-mail addresses
Click "Add e-mail address" and type the e-mail address
onto the text box and click Set button. To check the
registered addresses, click Check/Delete sub menu tab.
The addresses are listed as the figure on the right.
✐ Up to 10 E-mail addresses can be registered.
Check / Delete
To delete the registered addresses, check the address you
want to delete and click Delete button.
3O
ption selection for sending alert mail
Click Option sub menu tab. Check the condition items
under which alert mail will be sent and click Set button.
Please refer to item "Examples :Type and contents of alert
mail" described on the next page.
Option
[1]––––––––––––––––––––––––––––––––––
o When PJ lamp is off.
o When PJ lamp replacement time is reached.
o When internal PJ power circuit is failed.
o When internal PJ temperature is too high.
o When PJ is turned into Standby in proper user operation.
[2]––––––––––––––––––––––––––––––––––
o When Power management function turns PJ lamp
off.
o When the signal is interrupted.
[ ] hours.
Attached message
✐The length of message should be less than 256
ENGLISH
[3]––––––––––––––––––––––––––––––––––
o When lamp Corres. Value reaches
characters.
✐ Up to 99,999 hours can be set for use time.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
35
Chapter 3 Basic Setting and Operation
Examples: Type and contents of alert mail
When the projector has an abnormality, the following alert messages are sent to the registered E-mail address according to your selected condition. Administrator or user can take
an efficient action quickly by receiving this message. This is very useful to maintain and
service the projector.
The following are examples of received messages.
● When internal PJ temperature is too high:
TITLE: Message from projector
10-03-2005 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The Projector lamp is turned off, because internal Projector temperature is too high.
Wait for the completion of cooling process and make sure the projector has been turned
into Standby. Then turn the projecto on again.
If the Indicator continues flashing, check the air filter for dust accumulation.
[A] 81.5 degrees fahrenheit [B] 134 degrees fahrenheit [C] 95.6 degrees fahrenheit
Temperature of Sensor B is too high.
✐ The network unit let users know the information which thermal sensor [A], [B] or [C]
inside the projector detected the abnormal temperature risen and so the projector was
turned off. Please refer to item "Power control and status check" (☞ p.42) for the location
of the sensors and each temperature . Also see the owner's manual of the projector for
further details.
● When internal PJ power circuit is failed:
TITLE: Message from projector
10-03-2005 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The Projector lamp is turned off, because Projector power circuit is failed.
Unplug the Projector from AC outlet and ask servicing to qualified service personnel.
AV, -5V OK
AV, S5V OK
Error information
PJNET, S5V
OK
ANALOG,6V
NG
....
....
....
✐ The projector lamp was turned off, because the projector power circuit failed.
Unplug the projector from AC outlet and ask servicing to a qualified service personnel with
the error information.
36
E-mail setting
● When PJ lamp replacement time is reached:
TITLE: Message from projector
10-03-2005 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The projector lamp has reached replacement time.
Lamp replacement is required.
✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is
used without resetting the lamp counter, the alert mail is sent to users in every poweron of the projector. This alert mail will not be sent when unchecking the mail sending
condition "When PJ lamp replacement time is reached".
● When lamp corres. value reaches preselect use time:
TITLE: Message from projector
10-03-2005 00:59
Projector Model Name: model name
TCP/IP: 192.168.1.201 Projector Name: Proj05
It sends you following message.
*The accumulated lamp use time has reached 1200 hours.
Prepare for the lamp replacement.
Free messages
ENGLISH
✐ The network unit sends a free message when the lamp use time (Corresponding value)
reaches the preselected lamp use time. It can be used for preparation of the lamp
replacement and the maintenance required.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
37
Chapter 3 Basic Setting and Operation
SNMP setting
This product provides a SNMP (Simple Network Management Protocol)
agent function. The SNMP consists of a manager and agents. The group
which communicates information each other with SNMP is called
"Community". There are two access modes in a community, Refer (read only) and Set (readwrite). This product allows to use Refer (read only) only. The SNMP message informs the projector status called "Trap" to an administrator. Click SNMP setting on the main menu and set
up each item.
PJ information
Item
Description
Contact...................Enter user name of the projector etc. (optional)
Place.........................Enter place of the projector (optional)
Community
name(refer).........Enter community name (read only). Default name
is "public".
✐The SNMP agent provided with this product is based upon MIB-2 defined by RFC1213. For private
38
MIB information, refer to file "Mibinfo/12PjNet.mib" in the CD-ROM.
SNMP setting
Trap
Item
Description
Community name.......Enter community name to send "Trap". Default
name is "public".
Trap address........Enter IP address of the SNMP manager computer
to receive "Trap".
Trap check/delete
Check and delete the trap address
Checking the registered trap address and deleting the
address.
To delete the address, tick check box in front of the IP
address and click Delete button.
ENGLISH
✐ Up to 10 trap addresses can be registered.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
39
Chapter 3 Basic Setting and Operation
Trap option
Trap option setting
Tick check boxes in front of the condition item to send the
trap.
✐ Click Set button if you tick or un-tick the check box on a page.
[1]––––––––––––––––––––––––––––––––––
o When PJ lamp is off.
o When PJ lamp replacement time is reached.
o When internal PJ power circuit is failed.
o When internal PJ temperature is too high.
o When PJ is turned into Standby in proper user operation.
[2]––––––––––––––––––––––––––––––––––
o When Power management function turns PJ lamp
off.
o When the signal is interrupted.
o When lamp Corres. Value reaches
[
40
] hours.
✐ Up to 99,999 hours can be set for the time setting.
Chapter 4
Controlling the Projector
4
ENGLISH
Describes controlling and setting of the projector by using the web
browser.
41
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
41
Chapter 4 Controlling the Projector
Power control and status check
Click Power & Status on the main menu. The control page will be displayed.
By clicking ON or Standby button on the page, the power of the projector can be controlled.
Confirmation window
as shown in the below
appears when the
Standby button is pressed.
Item
Description
Popup confirmation window
PJ status
Power ..........................Displays the status of the lamp. (ON, OFF, On starting up, On cooling down)
Status ..........................Displays the status of the projector's power. (Refer to next page.)
Power control.........Controls the projector power by clicking the "ON" or "Standby" button.
PJ temp.
Inside temp.A ........Displays the surrounding temperature of lamp in the projector. (Sensor B)
Inside temp.B . .......Displays the surrounding temperature of panel in the projector. (Sensor C)
External temp. . .....Displays the surrounding temperature of the intake vent. (Sensor A)
..........The warning icon will appear if the temperature exceeds a specified value.
Check if there is no object to obstruct the airflow around the intake or exhaust
vent. It might be airfilter clogged. Clean up the airfilter.
* The temperature unit can be set either Centigrade or Fahrenheit in item "Initial
setting". (+p.30)
42
Power control and status check
About projector condition
Status
Description
Normal................................................................ Projector is operating normally.
Power management under operation... Power management is operating
Lamp failure.................................................... Lamp failure is occurring
Abnormal temperature.......................... The temperature of the projector became too high
Cooling off due to abnormal temp......................... Projector detects abnormal temp. and is cooling down itself.
Power failure ................................................. Power failure has occurred inside the projector. Projector is turned
off. Disconnect the AC cord and ask servicing to a qualified service personnel.
If the power failure occurs on the projector, "Power failure" is
indicated on the status column and the information icon appears
on the power column as shown below. Click this icon to display
further information of the power failure.
Click this icon to display
further information of
the power failure.
When a security (PIN code lock) has been set on the projector, you also cannot
control it through the network. To control the projector through the network
temporarily, execute "PJ lock suspend" command to unlock the security. "PJ lock
suspend" is on setting sub menu [3] on Setting main menu. (+p.50)
✐ The projector cannot be turned on while the projector is on cooling down.
✐ The web browser checks and updates the projector's condition every 30 seconds automatically.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
43
Chapter 4 Controlling the Projector
Controls
Click Control on the main menu. The setting method differs depending
on the contents of the page. Click on the page number to change pages
and select desired setting items.
✐ Please see the owner's manual of the projector to have the further information
of each control item.
Input
This function is to select the input mode and source mode of the projector. Click Set button after selecting the input and source mode.
Item
Description
Input..........................Selects input mode of the projector. (1 to 3)
Source......................Selects signal source of the input.
Input 1 : R
GB(PC analog)
RGB(Scart)
RGB(PC digital)
RGB(AV HDCP)
Input 2 :Video
Y,Pb/Cb,Pr/Cr
RGB
Input 3 :Video
Y,Pb/Cb,Pr/Cr
S-video
44
✐ The control page displays valid control items depending on the selected input mode, signal
or functions of the projector you use, therefore, there may be different controls between the
described items and actual control items on the page display. For further information , refer to the
projector's owner's manual.
✐ When the projector is in standby, only the timer on the setting menu is effective; others are inactive.
Controls
System
This function is to select the system of signal input to the projector. The available system
mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button.
Available selection at the RGB(PC analog) input
Item
Description
XGA1.........................It automatically switches to the proper computer
system of the input signal.
* The computer system modes (VGA, SVGA, XGA.
SXGA, UXGA, WXGA...) which meet the input signal are listed.
Available selection at the RGB(PC digital) input
Item
Description
D-XGA.......................It automatically switches to the proper computer
system of the input signal.
* The computer system modes (D-VGA, D-SVGA,
D-XGA. D-SXGA1...) which meet the input signal
are listed.
Available selection at the Video/S-video/Scart input
Item
Description
AUTO.........................It automatically switches to the proper color system of the input signal.
* The selectable color systems are PAL, SECAM,
NTSC, NTSC4.43, PAL-M and PAL-N.
* AUTO is fixed at the Scart input.
Available selection at the RGB(AV HDCP) input
Item
Description
AUTO.........................It automatically switches to the proper scanning
system of the input signal.
* The selectable scanning systems are D-480p,
D-575p, D-720p, D-1035i and D-1080i.
Available selection at the Y,Pb/Cb,Pr/Cr input
Description
AUTO.........................It automatically switches to the proper scanning
system of the input signal.
* The selectable scanning systems are 480i, 575i,
480p, 575p, 720p, 1035i and 1080i.
✐ If the mode (Mode1 to Mode 10, ExMode11 to ExMode50) which is stored in the item "PC
Adjustment" (☞ p.48) is available, they are also listed together with the above mode.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
Item
45
Chapter 4 Controlling the Projector
Image adjustment
This function is to adjust the projected picture image and save the image mode. To store
the adjusted value, click Store button, and to load the adjusted value, click Load button.
Item
Description
Contrast..................Adjusts picture contrast (0~ 63)
Brightness.............Adjusts picture brightness (0~ 63)
Color..........................Adjusts picture color saturation (0~ 63)
Tint.............................Adjusts picture hue (0~ 63)
Item
Description
Color Temp...........Sets a color temperature mode. (X Low, Low, Mid, High,
Adj.)
White Balance
Red, Green,
Blue......................Adjusts each white balance respectively. (0~ 63)
Sharpness..............Adjusts picture sharpness. (0~ 31)
* When changing the value of the white balance, the color temp.
indicates "Adj."
Item
Description
Gamma.......................Adjusts brightness of darker part of the picture. (0~
15)
Noise reduction...­Switches noise reduction mode (OFF, L1, L2)
Progressive . ..........­Switches progressive mode (ON, OFF, Film)
Reset.........................Resets the Image adjustment to previous levels.
Store..........................Stores the Image adjustment values. Select an
item [Image1 - Image10]
from the pull-down menu
and click Store button.
46
Load...........................Loads the Image mode.
Select an image mode
from the pull-down
menu and click Load
button. There may not be
available mode dependInput source
ing on the input mode as
Image mode Video Computer
shown in the table left.
*
Standard(AV) 4
Cinema
4
*
Standard(PC)
*
4
✐ T he mark "4 " means that the available image mode in the
Real
*
4
selected input source. The error message appears when
Image1 - 10 4
4
selecting the disabled image mode indicated with "*".
Controls
Sound
This function is to adjust the sound of the projector. The values in the text box represent
the current control value or status.
Item
Description
Volume....................Adjusts the sound volume from the speakers.(0 ~ 63)
Mute..........................Suppresses the sound. (ON, OFF)
Menu
This function is to control the On-screen menu of the projector. Switches menu on/off,
moves menu selection (cursor) and executes the selected menu item.
Item
Description
ENGLISH
Display.....................Switches the on-screen display menu on or off by
clicking ON or OFF button.
Cursor.......................Moves cursor selection by clicking 7, 8, e and
d buttons and executes the selected menu item
by clicking ■ button.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
47
Chapter 4 Controlling the Projector
PC adjustment
Click PC Adj. on the main menu. This function is to adjust the signal from
the computer connected to the projector to obtain the proper picture
image on the screen.
Item
Description
Current mode.......Displays a current mode like VGA, SVGA, XGA. SXGA,
UXGA, WXGA, etc. or MODE1 - MODE10, EXT11 EXT50 which are the customized mode created by
using the "Mode Store" function described below.
EXT51 - EXT60 represents mode Totalsave1 Totalsave10 used in the item "Save" (+p.51).
Auto PC adj..........Performs automatic adjustment.
Fine sync................Performs Fine Sync adjustment. (0 ~ 31)
Total dots...............Adjust the number of total dots in the horizontal
period.
Clamp.........................Adjusts the phase of the clamp. (1 ~ 255)
Display area
Horizontal...........Adjusts the image area horizontally.
Vertical...............Adjusts the image area vertically.
Item
48
Description
Position
Horizontal........Adjusts the horizontal position of the screen.
Vertical...............Adjusts the vertical position of the screen.
Reset.........................Resets the PC adjustments to the previous levels.
Mode Store...........Stores the PC adjustment values. Select a mode
no. [Mode1 - Mode10, ExMode11 - ExMode50]
from the pull-down menu.
Mode Free.............Clear the PC adjustment values. Select a mode
Up to 60 characters can be used for
no. [Mode1 - Mode10, ExMode11 - ExMode50]
the Memo of ExMode11 to ExMode50.
from the pull-down menu.
✐ The PC adjustment settings can be stored up to 50 sets, 10 sets for Mode1 to Mode10 are stored into
the projector and 40 sets for ExMode11 to ExMode50 are stored into the network unit.
Setting up the projector
Setting up the projector
Click Setting on the main menu. This function is to set up the projector.
Select the sub menu [Screen setting] or [Setting] and then set up each setting.
Item
Description
Screen......................Switches the screen mode. (Full, Zoom, Normal,
Natural wide, True) There may not be available
mode depending on the input mode as shown in
the table below.
Ceiling......................Sets the image top/bottom and left/right
reversed. (ON, OFF)
Rear............................Sets the image left/right reversed. (ON, OFF)
Input source
Full
Zoom
Normal
Natural wide
True
4
4
4
4
*
4
*
4
*
4
✐ T he mark "4 " means that the available screen mode in the
selected input source system. The error message appears
when selecting the disabled screen mode indicated with "*".
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
Screen modeVideo Computer
49
Chapter 4 Controlling the Projector
Item
Description
Logo..........................Sets on or off the logo display on the screen during the startup. (Default, User, OFF)
Background..........Sets screen background to blue when no signal
input. (Blue, User, Black(OFF))
Display.....................Switches on or off the on-screen menu display on
the screen. (ON, OFF, CountdownOff )
Freeze.......................Sets the image to freeze mode. (ON, OFF)
Power
management......Sets into the selected power management mode
(OFF, Ready, Shutdown) if the input signal is
interrupted and no control key is pressed for the
specified period of time.
*The specified time can be set 1 to 30 min.
On start...................Sets the power-on mode when connecting the
AC cord to the outlet. (ON, OFF)
Item
Description
Lamp control*....Selects lamp control mode. (Normal, Eco, Auto)
This function may be disabled depending on the
projectors.
Lamp
Corres. Value(h)Displays the lamp use time (Corresponding
value) . Reset the time after lamp replacement.
Lamp Corres. Value Reset
1. Select a Lamp-1 radio button and then click Reset button.
2. Click OK button to execute the reset.
Item
50
Description
Remote control
ID........Sets the remote control ID. (Code 1 - Code 8)
Fan speed control......... Sets the fan control speed. (Normal, Max)
Status ...............Indicates the current fan mode.
Factory default...........Sets all of the projector control items to the factory default setting except the following items.
Lamp Corres. Value, PJ time, Network PIN code,
Network setting
* This function is not effective for the settings
of the network unit, Network address settings,
e-mail settings, etc.
PJ lock suspend............. When the projector has a security of PIN code
lock, disable this function temporarily by pressing
Execute button.
Setting procedure
1. Turn off the projector , disconnect AC cord from the outlet
and then connect AC cord again.
2. A
ccess this page with the web browser,
3. Click Execute button on the PJ lock suspend.
* This function is disabled after the projector turns on.
Save the controls and settings
Save the controls and settings
This page is to save and load the controls and settings of the projector in
the block. The storable items are "PC adjustment", "Control" and "Setting".
Store/free the settings
1 Click Save menu on the main menu.
2 Select a set number (Totalsave1 to Totalsave10) you intend to store current settings with
the pull-down menu button of the item Store & Free. Name this set number onto the
Memo text area.
* Up to 18 characters can be used for the Memo.
3 Click Store button to store the current setting and
name into the selected set number.
To remove the saved setting, select the set number
with pull-down menu button and then click Free
button.
Type a memo for
the selected set
number
✐ You can store up to 10 (Totalsave1 to Totalsave10) sets of settings into the network unit. Totalsave1
to Totalsave10 are indicated on the item "Current mode" of the PC adjustment (+p.48) as the
EXT51 to EXT60.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
Select a set
number
51
Chapter 4 Controlling the Projector
Check the saved items
Click Check button to check the current setting condition of the controls. Each item of "PC
adj.", "Control" and "Setting" is displayed sequentially.
Click Stop button to cancel
the auto page display.
Load a control set
Select your desired set number
(Totalsave1 to Totalsave10) with the pulldown menu button of Load Set and then
click Load button. The setting values of
the selected set number are applied to
the current settings.
52
Select a set
number
✐ If the contents of the saved set are not matched for the inputs equipped on the projector, the
invalid alert message may be displayed.
Timer setting
Timer setting
This page is to set the timer to turn the projector off or on at a programmed day/date and time. Follow the steps below for setting.
Click Timer on the main menu.
Present time set on the
network unit
Select date
Select day
Set execute time
Event
action
How to set the timer
1 Set a day or date
To set the timer event at same time everyday or every week,
Select day entry with radio button and then select desired day with the pull-down menu
button.
The selectable days are as follows:
- Every week ( a day from Monday to Sunday)
To set the timer event on specified date,
select date entry with radio button and then type the date with (Year/Month/Date) format.
Ex.: Type [2005/12/20] if you specify [December 20, 2005].
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
- Same time everyday
53
Chapter 4 Controlling the Projector
2 Set an execute time
Type the time with (Hour:Minute) and 24 hours format.
Ex.: Type [18:25] if you specify [PM 6 o’clock and 25 minutes].
3 Select an event action
Select an event action from the pull-down menu.
Event
Action
ON...................................Turns on the projector
OFF.................................Turns off the projector
Lamp Normal..........Changes lamp mode to "Normal"
Lamp Eco...................Changes lamp mode to "Eco"
Lamp Auto................Changes lamp mode to "Auto"
*Available events depends on the projector function.
4 Register an event
Click Set button to register the set timer event. Repeat steps 1 to 4 for another timer
event setting.
Check the timer events
To check the set timer events, click Check button. The timer
events are listed. The event with blue background color represents the timer-OFF event.
Change the event mode
On the event list appearing by clicking Check button, click
on the event you want to delete, disable or enable. Click
Cancel, Delete, Timer ON or Timer OFF button on the
popup pallet.
Button
Operation
Cancel......................Cancels the setting
Delete.......................Deletes the timer event
Timer OFF..............Disable the timer event temporarily
Timer ON................Enable the timer event
54
Timer setting
Notes on timer setting
✐ Up to 10 timer events can be registered. Timer events always operate according to the next valid
event depending on the projector's power status. In the example below, event 3 turns on the
projector so next event 4 (also turning on projector) will not be effective because the projector
is already turned on. Similarly, when the projector is turned off by event 5, event 6 OFF will not
be effective in turning it off again. But these secondary events (event 4 and event 6) will become
effective if a person turns off the projector (after event 3 and before event 4) or turns on the projector (after event 5 and before event 6).
Invalid event
Projector Power
Event 1
Event 2
Event 3
Event 4
Event 5
Event 6
ON
OFF
Invalid event
ON
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
Time
✐ When the timer events are set at the same time, the last event set will override the previous
events. For example, if there is an event like "ON at 8:00 everyday" and then new event is set like
"OFF at 8:00 everyday", only the last setting event is effective.
✐ When the timer event ON occurs during cooling down period, this is invalid event because the
projector cannot be turned on during this cooling down period.
✐ The timer operates by using the clock function provided in this product. Before setting the timer,
please confirm that the current date and time are set correctly. Timer and clock functions are
functioning using a lithium battery provided in this product. When the battery runs down, the
clock and timer functions will not operate correctly. Consult your local dealer for the replacement
of battery. The replacement must be carried out by a qualified service personnel.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
55
Chapter 4 Controlling the Projector
Projector information
This page is to display the basic information of the projector status. Click
Information on the main menu.
Items
Description
Input..........................Displays selected input and source.
System.....................Displays selected signal system.
Signal........................Input signal status (Yes, No)
Screen......................Displays screen mode.
Lamp status...........Displays lamp status with an animation. Refer to
the table on the next page.
Security...................Displays the security (PIN code lock) status (Yes, No)
Click this button to
update the information
56
Projector information
Indication of the lamp status
Icon display/background Status
White-Yellow/Blue
Lamp on (Normal)
White-Yellow/Red
Lamp on (Lamp is being used over a specified use time, replace lamp
immediately)
Gray/Blue
Lamp off (Normal)
Gray/Red
Lamp off (Lamp is being used over a specified use time, replace lamp
immediately)
Red/Blue with X
Lamp failure (Lamp failure, check lamp condition)
Red/Red with X
Lamp failure (Lamp failure and lamp is being used over a specified use
time, replace lamp immediately)
Items
Description
ENGLISH
PJ time......................Displays the accumulated use time of the projector.
Lamp Corres.
Value.........................Displays the use time (Corresponding value) of
the lamp.
Timer.........................Displays the timer setting status.
ON Timer has been set.
OFF No timer setting.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
57
Chapter 4 Controlling the Projector
Multi-control
Controlling and setting the multi-projectors
This function enables you to control the multiple projectors equipped with
the network units that are connected to the network. Click Multi Control on the main
menu to display the control page.
Note: To control the multiple projectors, each projector must have the same Network PIN code.
Example of multi control
PJ1
PJ2
PJ3
PJ4
PC6
PC5
58
PC4
Select Input2 for
PJ1 to PJ4.
Multi-control
Start/stop the multi control
Switches on and off the
multi-control function
To start or stop controlling the multi-projectors, click
Multi control setting menu and select ON or OFF.
Multi control setting
OFF.........Stops multi control function
ON...........Starts multi control function. The multi control
menu will appear when setting ON. These
items of menu are linked to the main menu.
The multi controllable menus are "Power & Status", "PC
adjustment", "Control", "Setting", "E-mail setting", "Timer"
and "SNMP setting". Click each menu and perform setting and adjustment.
✐ The word "MULTI CONTROL" appears on the each control
page while the multi control is operating.
This shows the multi control is operating now.
ENGLISH
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
59
Chapter 4 Controlling the Projector
Register the projector
To use the multi control function, register the IP address of the projector you intend to control. Click PJ registration sub menu tab and set the IP address and Memo, then click Set
button.
Items
Description
IP address...........Enter IP address of the projector to control
Memo.......................Enter projector name or installed location etc.
Confirmation of registered projector
To check the registered information, click Check&
Change sub menu tab. The registered information of
the projector is listed as the below.
* The word "None" is displayed if not using the "Memo" function.
* When you click on a listed IP
address, the login page for the
selected projector will be displayed with a new window.
IP address
Status
Memo
Page no.
Click here to close
the sub menu Check
& Change.
60
✐ 10 projectors per page can be registered and up to 100 sets can be registered for the multicontrol.
Multi-control
Change the mode of the registered projector
To change the mode of the registered projector, select a mode with the pull-down menu
button under the IP address of the target projector and then click Set button.
Mode
Operation
Control......................... Multi-controlling the projector
OFF.............................. Excluding from the multi-control
Delete.......................... Deleting from the multi-control
* This function is not available with the Light mode.
Status
If some of the registered projectors are disabled by
some reasons (such as disconnecting the power source,
disconnecting the LAN cable, disconnecting from the
network), control changes will continue to be effective
for the projectors that are still active. At the same time,
the deactivated projectors are excluded from the multicontrol. The status of the registered projectors are indicated under the projector name. See the table below
for status indications.
Status
Status
Description
(blank).....................The projector is connected to the network correctly
No connect...............The projector may not be connected to the network. Please check the connection
and network configuration of this projector.
PIN code error........The PIN code is incorrect. The PIN code for the multi-controlled projectors must be
the same. Change the PIN code of this projector to the common PIN code. (+p.22)
✐ If the multi-controlled projector is in the standby mode, any change is not effective except timer
setting.
✐ It is recommended that a specified projector should be chosen for setting as a master when you
use this multi-control function. The control for the multi-controlled projectors will become too
complicated operation if this function is used for each projector.
✐ If the registered projector is not connected to the network, it will take some time to complete the
multi-control operation because of waiting for the response from each registered projector.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
* The Network Unit updates the status at the time when the multi-control function was executed.
61
Chapter 4 Controlling the Projector
Check & Change page in the light mode
Following functions in the "Check&Change" page are
not available in the light mode.
- Changing the control mode.
- Deleting the registered IP address
- Indicating the each status
- Indicating the each memo
This indicates that the
mode is "Control".
Connection status
Blinking: Connected
Gray: Disconnected
(Check&Change page in the light mode)
Controlling all together
"Power & Status", "PC adjustment", "Control" and "Setting"
can be controlled all together. Set "ON" the multi control
setting and adjust controls of each menu. The setting
value is applied to the registered projectors sequentially .
✐ This is effective only if the mode of the registered projector is
set to "Control".
Setting all together
"E-mail setting", "SNMP setting" and "Timer" can be set all
together. Set "ON" the multi control setting and items of
each menu. The setting value is applied to the registered
projectors sequentially.
✐ This is effective only if the mode of the registered projector is
set to "Control".
62
Chapter 5
Use of Serial Port
ENGLISH
Describes controlling the external equipment connected with the
serial port.
63
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
63
Chapter 5 Use of Serial Port
T his product provides a serial control port to control the external equipment through the
serial cable. This function allows you to control the external equipment connected to the
serial port on the network unit through the network, and control the projector through the
serial cable with the external serial controller. Before connecting the external equipment,
perform the setting "Serial Port setting" described below.
Serial port setting
This is to set up the serial port on the network unit. Display the setting
page by clicking Serial Port setting sub menu in the Initial setting
menu. To communicate with external equipment correctly, communication condition must be set up to the same values as that the connected equipment is
using. When clicking on any item of the serial port setting, the setting pallet appears and
set up each item and then click Set button*1.
Item
Description
Baud rate................Communication speed for serial port, select with the pull-down menu (300 ~ 115200)
Parity.........................Parity check, the ways for error detecting of the transferred data (None, Odd, Even)
Stop bit....................Stop bit, Select the end of communication (1 or 2)
Flow control.........Ways for communication flow (None, Xon/Xoff, RTS/CTS)
Data length..........Selects the length of data (7 or 8)
Serial control.......Selects equipment to control (External or Projector)
External.............Used to select when the external equipment connected to the serial
port is controlled by the computer through the LAN port.
Projector..........Used to select when the projector is controlled by the serial controller
connected to the serial port.
Port number........Specifies the port number of TCP/IP. The default number is 23. Use the same port
number specified by application. There are some reserved port numbers*1. If one of
those port numbers is used, the alert dialog window will appear and let you know
that it is an invalid port number.
64
✐ This product will restart when "Port number" or "Serial Control" is changed and it takes about 20
seconds.
Serial port setting
Setting examples for the serial control
Setting for controlling the equipment connected to
the serial port from the computer. See example 1 of item
"Control examples" (☞ p.66).
Serial Control
Port number
Other Settings
:Selects "External"
:Sets according to the computer specified port
no. Do not use port number 10000*1.
:Sets according to the communication condition
of the equipment
Setting for controlling the projector from the serial controller connected to the serial port. See example 3 of item
"Control examples" (☞ p.67).
Serial Control
Port number
Other Settings
:Selects "Projector"
:Not specified. Do not use port number 10000*1.
:Sets according to the communication condition
of the serial controller
Setting for controlling the projector from the computer
through the LAN port.
Serial Control
Port number
Other Settings
:Not specified
:Not specified
:Not specified
*1 T he reserved port numbers are http (80), ftp (21), SNMP (25), POP3 (110) etc. The port number
4352, 10000, 10001 are reserved to control the projector through the LAN port.
✐ E xclusive driver software for control of the external equipment is required. This product does not
provide any driver software. Please consult your local dealer.
✐ There are 2 types of serial cables, Normal(Straight) and Reverse(Cross) type. Usually, when connecting between this product and a projector or a computer, use Reverse type of serial cable.
When connecting DVD player etc., use Normal type.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
* The port number of the computer must be used with 10000.
* Refer to item "Control the projector with telnet" (☞p.70) for the
detailed usage.
65
Chapter 5 Use of Serial Port
Control examples
Example 1
Controlling AV equipment through network.
Video/Audio
PJ2
DVD Player
LAN cable
PC5
Playback DVD
Serial cable
Connect the serial cable between the serial ports on the network unit and external
equipment.
Example 2
Controlling a projector not provided with the network function through network.
PJ2
PJ1
LAN cable
PC5
Turn on the PJ1.
Serial cable
Connect the serial cable between the
serial ports on the network unit and the
projector you wish to control
66
Control examples
Example 3
Controlling the projector with the serial controller through the serial port.
PJ3
PJ2
PJ1
Serial cable
Connect the serial cable between the
serial ports on the serial controller and the
projector or network unit.
Serial controller
ENGLISH
✐U
se proper serial cable depending on the connected equipment port specification. Please refer
to "Port Specification" of the serial port specification of this product (☞ p.80).
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
67
Chapter 5 Use of Serial Port
Use of telnet
You can control the external equipment connected to the serial port on the network unit
by using the telnet application*1 installed on your computer. The following is a control
example of external equipment. The telnet application is needed to use commands*2
which control the external equipment.
Preparation
1 D isconnect the AC plug from the outlet, and connect the serial cable between the serial
2
3
4
ports on the network unit and external equipment. (Refer to the note on the page 67 for the
type of the serial cables.)
T urn on the projector and external equipment.
D
isplay the setting page by clicking Serial Port setting sub menu in the Initial Setting main
menu with the web browser. Display the setting pallet by clicking any of the items on the serial
port setting page.(☞ p.64).
C
hange the serial port setting to be the same communication condition as the connected
external equipment and then click Set button (☞ p.64).
The following example setting is for our projector communication condition. When controlling our projector
set as follows:
Control
Baud rate............................19200
Parity.....................................None
Stop bit................................1
Flow control.....................None
Data length.......................8
Serial control....................External
Port number.....................23
(For example, in case of using the Telnet application of the Windows XP Professional.)
1 S elect Run... submenu from Start menu on the computer. Type "telnet" onto the Open
text area on the displayed window and press OK button.
2 T he telnet application will start and the following window will be displayed. Type as below
to connect the projector.
> open 192.168.1.201 [return]
68
*Use the IP address assigned to the projector
Use of telnet
3W
hen communication is established, the word "PASSWORD:" appears on the window. Type
the login password (PIN code) for the projector and then press "Enter" key on the keyboard.
If you do not set up the Network PIN code, just press "Enter" key.
When the word "Hello" is replied, login has been succeeded.
4 T ype the commands from the key board to control the external equipment and
then press "Enter" key for termination. For example, type "C00" and press "Enter" key.
* "C00" is a command to turn the projector on.
- The extra projector will be turned on.
To disconnect the communication, press "Ctrl" key and "]" key at the same time.
*1 F urther instructions about the telnet application, please see the on-line guide on your computer.
*2 T he commands are defined by each product independently, so please consult the manufacturer
or sales dealer for further information of the commands.
* The password is a Network PIN code decided item "Network PIN code setting" (+p.22, 31). If the
authentication of the entered password is failed 4 times continuously, the communication will be
disconnected automatically. Please try again for the connection.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
69
Chapter 5 Use of Serial Port
Control the projector with telnet
This product allows you to control the projector by using the telnet application. Normally,
it is used for controlling the external equipment connected to the serial port but it also
controls the projector by specifying the telnet port number 10000.
* To control the projector with telnet application is not depending on the serial
port setting.
In the step 2 of the previous item "Control"(☞ p.68), enter port number "10000" after the IP
address number.
> open 192.168.1.201 10000 [return]
* Use the IP address
assigned to the projector
After the communication is established, type the password (PIN code) and the command
for controlling the projector and then press "Enter" key.
The table below shows the typical command lists for controlling the our projector and
please consult your local dealer for further information of another commands.
Command list table
Command Function
70
C00Power on
C02
Power off
C05
Selects input1
C06
Selects input2
C07
Selects input3
C09
Volume up
C0A
Volume down
C0B
Audio Mute on
C0C
Audio Mute off
C0F
Screen Normal size
C10
Screen Full size
C1C
Menu display on
C1D
menu display off
C23
Input2 (Video)
C24
Input2 (Y,Pb/Cb,Pr/Cr)
C25
Input2 (RGB)
C33
Input3 (Video)
C34
Input3 (S-Video)
C35
Input3 (Y,Pb/Cb,Pr/Cr)
Chapter 6
Appendix
6
Connection examples
Web browser setting
Technical data
ENGLISH
Q&A
71
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
71
Chapter 6 Appendix
Examples of connection
Peer-To-Peer connection
Connecting the projector (PJ01) to the control computer (PC05) directly.
* UTP cross cable
Computer Name: PC05
IP Address
: 192.168.0.5
Subnet Mask
: 255.255.255.0
Default Gateway :
DNS
:
Projector Name: PJ01
IP Address
: 192.168.0.2
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
DNS
: 0.0.0.0
Connecting the projector (PJ01) to the control computer (PC05) via the hub.
Hub
To another network
Computer Name: PC05
IP Address
: 192.168.0.5
Subnet Mask
: 255.255.255.0
Default Gateway :
DNS
:
Projector Name: PJ01
IP Address
: 192.168.0.2
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
DNS
: 0.0.0.0
Computer Name: PC10
IP Address
: 192.168.0.10
Subnet Mask
: 255.255.255.0
Default Gateway :
DNS
:
72
✐ When the projector is connected to the computer directly without hub, the UTP cross cable
should be used.
Examples of connection
The gateway (Router) installed in the network
Connecting the projector (PJ01) to the control computer (PC05) via the gateway.
Entrance hall
Computer Name
IP Address
Subnet Mask
Default Gateway
DNS
: PC205
: 192.168.200.5
: 255.255.255.0
: 192.168.200.1
: 192.168.201.1
Projector Name: PJ01
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.200.15
: 255.255.255.0
: 192.168.200.1
: 192.168.201.1
Hub
Network Group: 192.168.200.x
Gateway (Router)
To another network
IP Address : 192.168.200.1
IP Address : 192.168.100.1
IP Address : 192.168.10.1
Office
Hub
Computer Name: PC05
IP Address
Subnet Mask
Default Gateway
DNS
: 192.168.10.5
: 255.255.255.0
: 192.168.10.1
: 192.168.201.1
Computer Name
IP Address
Subnet Mask
Default Gateway
DNS
: PC10
: 192.168.10.10
: 255.255.255.0
: 192.168.10.1
: 192.168.201.1
Computer Name
IP Address
Subnet Mask
Default Gateway
DNS
: PC51
: 192.168.10.51
: 255.255.255.0
: 192.168.10.1
: 192.168.201.1
Computer Name
IP Address
Subnet Mask
Default Gateway
DNS
: PC61
: 192.168.10.61
: 255.255.255.0
: 192.168.10.1
: 192.168.201.1
ENGLISH
Hub
Network Group: 192.168.10.x
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
73
Chapter 6 Appendix
Web browser setting
This product is designed to enable the projector to be set up and controlled from an
Internet web browser. Depending on the preference settings of the web browser, some
control functions may not be available. Please make sure that the following functions are
set up properly in the web browser.
Active Script/JavaScript enable
There are some control items used with
the JavaScript function in the setting
pages. If the web browser is set not to use
this JavaScript function, it may not control
the projector properly. In this case, the following warning message will be displayed
on the top of the page. To enable the
JavaScript, please see further instructions
on the next page.
Flash Player enable
The setting page of this product contains
the Flash contents. To display the setting
page, the Adobe Flash Player version 6
or later is required to be installed on your
computer. For further product information, see the Adobe homepage. (http://
www.adobe.com). Even if your computer
provides the Adobe Flash Player and the
setting page does not appear on the web
browser, check that Flash Player PlugIn(Shockwave Flash) is installed and set up correctly. please see further instructions on the
next page and it is depending on the web browser.
Proxy setting
In some cases, your web browser is set up to use the proxy server for the internet or
intranet connection. In this case, when you install this product into the local network, you
should set up the proxy setting of web browser preference correctly. Especially when connecting the projector and computer with a UTP cross cable directly, or when the network
does not provide the proxy server, make sure that "not use proxy server" is set up in your
web browser preference. Please see item "Examples: OS/Browsers" in the next page for
further setting up procedure.
74
✐ There are various ways to change your browser preferences depending on the version or applications. Please see the setting instructions on next page for example and also refer to on-line help
of your web browser.
Web browser setting
Examples: OS/Browsers
Windows XP Professional
Internet Explorer v.6.0
ActiveScript setting
Select Internet Options from Tools menu on the web browser and then select Security
tab and click Customize Level… button. On the security setting window, scroll down and
find the Scripting item, make sure that "Enable" is selected in item Active Scripting.
Flash Player enable
ENGLISH
ActiveX controls and plug-ins setting
Select Internet Options from Tools menu
on the web browser and then select Security
tab and click Customize Level… button. On
the security setting window, scroll down and
find the ActiveX controls and Plug-ins item,
make sure that "Enable" is selected in item Run
ActiveX controls and plug-ins.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
75
Chapter 6 Appendix
Flash Player Add-on setting
Select Manage Add-ons... from Tools
menu on the web browser. Select "Add-ons
currently located in Internet Explorer" from
Show pull-down menu. Make sure that the
"Shockwave Flash Object" is listed under the
item "Enabled".
Proxy setting
Select Internet Options from Tools
menu on the web browser and then select
Connection tab and click LAN Settings
button. Properly set up your web browser's the proxy server settings according to the
local area network environment to which the projector is connected.
- Using proxy server
To use an external internet connection from the local area network, check the item Use a
proxy server and enter the proxy server address and port correctly in the proxy settings
window. For further instruction please consult your network administrator.
- Not using proxy server
Uncheck the item Use a proxy server.
If you connect the projector to the computer directly with UTP cross cable, this must be
unchecked.
To designate proxy settings that will not use the
proxy server when accessing the projector installed
in the local area network, enter the IP address or
domain name here.
76
Web browser setting
Netscape Navigator v.7.0
JavaScript Setting
Select Preference from Edit
menu on the web browser
and then selec t the item
Advanced/Scripts & Plugins
in the Category column. Make
sure that the Enable JavaScript
for Navigator is checked.
Flash Player enable
ENGLISH
Flash Player Plug-in setting
Select About:Plug-ins from Help
menu on the web browser. The
plug-ins software provided on the
browser are listed on the page.
Check that the Flash Player Plugin (Shockwave Flash) is installed
and set up correctly as the below.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
77
Chapter 6 Appendix
Proxy setting
Select Preference from Edit menu on the web browser and then select the item Advanced/
Proxies in the Category column. Properly set up your web browser's the proxy server settings according to the local area network environment to which the projector is connected.
- Using proxy server
When you use an external internet connection from the local area network, select the item
Manual proxy configuration. Enter the proxy server address and port number correctly on
HTTP Proxy item. For further instruction please consult your network administrator.
- Not using proxy server
Select the item Direct connection to the Internet in the proxy setting window.
If you connect the projector to the computer directly with UTP cross cable, this must be
selected.
To designate proxy settings that will not use
the proxy server when accessing the projector installed in the local area network, enter
the IP address or domain name here.
78
Product specification
Product specification
Type........................................................... PJ-Net Organizer (network unit)
LAN interface....................................... Applicant regulation IEEE802.3 (10Base-T)
IEEE802.3u (100Base-TX)
Data transfer speed
10Mbps/100Mbps
Data transfer mode
Half duplex/Full Duplex
Terminal
8-pin modular (RJ-45)
Network protocol..............................TCP/IP specification
TCP/IP
Serial interface.................................... Baud rate
0.3/1.2/2.4/4.8/9.6/19.2/28.8/57.6/115.2 Kbps
Flow control
Hardware flow control (RTS/CTS, Xon/Xoff )
Parity check
Odd/Even
Terminal
Mini DIN-8 pin
Power source....................................... Supplied from the projector
Power consumption....................... 3.0 watts
Dimensions (W x H x D)................ 5.20" x 4.13” x 1.32” (132 x 105 x 33.6 x mm)
Weight..................................................... 0.57 lbs (258 g)
Built-in battery.................................... Lithium battery, Type CR2032, 3.0V
Operating temperature................ 41˚F ~ 95 ˚F (5˚C ~ 35 ˚C)
Storage temperature...................... 14˚F ~ 140˚F (-10˚C ~ 60˚C)
ENGLISH
* The specifications are subject to change without notice.
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
79
Chapter 6 Appendix
Port specification
LAN port specification
8-pin modular connector (RJ-45)
12 3 4 5 6 7 8
Pin No.
Signal
1
TX+
Transfer data (+)
Function
2
TX-
Transfer data (-)
3
RD+
Receive data (+)
4
(not used)
5
(not used)
6
RD-
7
(not used)
8
(not used)
Receive data (-)
Serial port specification
Mini DIN-8pin connector
8
5
7 6
4 3
2 1
80
Pin No.
Signal
1
(not used)
Function
2
(not used)
3
(not used)
4
Ground
5
RXD
RXD
6
TXD
TXD
7
(not used)
8
(not used)
Ground
Q&A
Q&A
Installation/Access
Q Why doesn’t the setting page appear in my web browser?
A
Following causes are possible. Please check them.
1. The projector does not connect to the network.
Check LED indicators status (☞ p.17).
- Check the connection of LAN cable if the LINK indicator does not illuminate
red.
-C
heck the network configuration of the projector if ACT indicator does not
illuminate green.
2. Function "Network" in the projector is not set to "ON". Set up by using the projector’s on-screen menu (☞ p.20).
3. Wrong network configuration of the projector
Check the network configuration of the projector by using the projector’s
on-screen menu (☞ p.20).
4. Wrong network configuration of the computer.
Check the network configuration of the computer.
5. The network unit is used with the default setting (☞ p.20).
6. The proxy setting of the web browser is not set correctly (☞ p.74).
7. The computer does not provide TCP/IP protocol.
Q No setting page in my web browser? Is the problem in the network or in
the projector? I would like to find out the problem whether it is in the
network or in the projector
Check it by the following steps
1. Disconnect the projector from the network and connect the projector and
computer with the UTP cross cable directly.
2. Change network configuration of the computer and projector as shown in the
example below.
(Projector setting)
IP Address
Subnet Mask
Default gateway
DNS
: 192.168.0.2
: 255.255.255.0
: 0.0.0.0
: 0.0.0.0
(Computer setting)
IP Address
Subnet Mask
Default gateway
DNS
: 192.168.0.5
: 255.255.255.0
: (blank)
: (blank)
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
ENGLISH
A
81
Chapter 6 Appendix
3. Enter the projector’s IP address [192.168.0.2] at "Address" column on the Web
browser. [Note] Make sure that the proxy setting of your web browser is set
"Not use a proxy server" (☞ p.74).
4. If the login page appears, this product is operating properly. The problems
may be in the network configuration of the computer or in the network. Please
try to set up the network by following item "Network configuration" (☞ p.20).
If the login page does not appear, please check for proper mounting of this
product onto the projector by referring to chapter "Installation and Network
configuration" (☞ p.18-19).
Q How can I restrict access from the computer.
A
1. Please use the password authentication function on the login page (☞ p.26).
2. Please use the IP filtering function provided with the gateway (router) to
restrict the accessing from the computer. For further information please consult your network administrator.
Q C an I access the projector installed on the company’s local area network
from a remote location?
A
T here are some ways to access to the projector in the LAN, but you must consult
your network administrator for security reason.
☛ Use of modem
(Connect to the company’s network from your home or some other places by
using modem.)
☛ Use of private line
(Connect to the company’s network from the branch office or maintenance
office by using private line.)
☛ Use of internet
(Connect to the company’s network from your home, branch office or some
other places by using the internet.)
Q W
e use the DHCP/BOOTP server to assign the IP address. Is it possible to
use the network unit in this network environment?
A
82
Possible. As the network unit does not support the DHCP/BOOTP server, the fixed IP
address must be configured manually. Please consult your network administrator
(☞ p.24).
Q&A
Q H
ow can I install several projectors equipped with the network unit?
A
Install and configure network one by one to avoid the IP address collision each
other (☞ p.24).
To configure the IP address please see item "Network configuration" (☞ p.20).
Q How many projectors can I control with multi-control function?
A
It has been designed to control up to 100 sets but it depends on the network environment.
Password/Login
Q What should I do when I forget the password?
A
Select "Network PIN code" sub menu from "Network" menu on the projector. For
further information, please see item "Network PIN code setting" (+p. 22).
Q C an I register the setting page as a web browser "Favorites" or
"Bookmarks"?
Please add "Login" page to your "Favorites" or "Bookmarks". Do not add the specified setting page because it will not be able to perform the password authentication correctly.
ENGLISH
A
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
83
Chapter 6 Appendix
Operation
Q Why can't I change the controls in the setting page with web browser?
A
Please make sure the projector is turned on. If it is in the standby mode, the setting
is not effective to the projector. To control the projector with a web browser, the
projector must be in the powered-on condition. Also, projectors registered for
multi-control cannot have any controls changed if they are in standby mode. But
timer and clock settings are always effective, even for projectors in standby mode.
Q Why does it sometimes take a lot of time to complete the page display?
A
The display speed of the page depends on the network environment in which both
the projector and computer are placed. It may take much time to complete the
page display if network traffic is heavy. Please consult your network administrator.
You can select the Light mode for displaying pages quickly (☞ p.26).
Q I use many of the projectors in the network. How can I use names of the
projectors to recognize each projector instead of IP addresses?
A
Y ou can manage the projectors with nicknames instead of the IP address. Please see
item "Multi-control" for further information (☞ p.58).
By registering the projector name and IP address with the DNS server, it can be
accessed with the nickname from the any computer referred to the DNS server.
Please consult your network administrator.
Q H
ow many numbers of the E-mail address can I register in the E-mail setting page.
A
84
You can register up to 10 addresses.
Q&A
Q Why am I not receiving E-mail alert messages?
A
Make sure that the registered E-mail address and SMTP server address are correct. If
the SMTP server is located in your LAN (Local Area network), the address should be
set to the SMTP server in your LAN. The SMTP server located outside of your LAN
may not be available for security reason. For further information please contact your
network administrator (☞ p.34).
It may be required for the authentication depending on the SMTP server. This product does not support this kind of SMTP server.
Others
Q Can I develop a driver to control external serial equipment?
A
This product does not provide any driver software. To control the external equipment connected to the extra serial port, it should be required to clarify the commands and communication condition defined by each equipment. If they are clarified, it can be controlled by using the Telnet application installed on your computer.
Please see item "Use of telnet" (☞ p.68).
Q Can I control the projector by using the telnet application?
P
ossible. Please refer to the item "Control the projector with telnet" (☞ p.70).
ENGLISH
A
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
85
Chapter 6 Appendix
Q Can I update the firmware of the network unit.
A
It is possible to update the firmware through the network. It is required to have a
special tool for the updating. For further information please consult your local dealer. The version number of the firmware is indicated on the lower part of the "Initial
setting" page.
Version of the
firmware
86
Q&A
Q What are the rules for IP address assignment?
A
If the network is constructed with TCP/IP protocol, a unique IP address is required
for each piece of network equipment. The following are basic rules of the assignment.
Rule1
Do not configure the same IP address to the network equipment in the
same network group. Each piece of equipment must be assigned a unique IP
address.
If the IP address is set [192.168.x.x], the Subnet Mask should be set
[255.255.255.0] for example.
Rule2
The start address [xxx.xxx.xxx.0] and the last address [xxx.xxx.xxx.255] of
the IP address must not be assigned to any other equipment. These address
numbers are reserved.
Rule3
The IP address must correlate to a network number. If network numbers are
different between the equipment, they cannot establish communications
each other. In this case, the router is placed in the networks to make the routing.
Q What is the MAC address assigned to the network unit?
The MAC address is indicated on the case back as the below.
MAC Address
MAC address
ENGLISH
A
PJ-NET ORGANIZER
OWNER'S MANUAL [PLV-80/75 Series]
87
OWNER'S MANUAL POA-PN02C for PLV-80/75 Series
IFFF
SANYO Electric Co., Ltd.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising