Sanyo SCP-2700 User's Manual

Sanyo SCP-2700 User's Manual
INSTRUCTION MANUAL
DVC-2700
DVD Player + Video Cassette Recorder
English
Lecteur DVD + Magnétoscope à cassette
Français
Only cassettes marked
can be used with this DVD+VCR.
As an ENERGY STAR® Partner,
SANYO has determined that
this product or product model
meets the ENERGY STAR®
guidelines for energy efficiency.
Please read this manual carefully before connecting your DVD+VCR and operating it for the first time.
Keep the manual in a safe place for future reference.
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU’AU FOND.
WARNING: Do not install this equipment in a confined space
such as a book case or similar unit.
NOTE TO CABLE/TV INSTALLER: This reminder is provided to
call the cable TV system installer’s attention to Article 820-40 of
the National Electric Code (U.S.A.). The code provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of the cable entry as practical.
CAUTION:
This DVD+VCR employs a Laser System.
To ensure proper use of this product, please read this owner’s
manual carefully and retain for future reference should the unit
require maintenance, contact an authorized service location.
Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
2
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
REGULATORY INFORMATION: FCC Part 15
This product has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is
operated in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the product and
receiver.
Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
NOTES ON COPYRIGHTS:
It is forbidden by law to copy, broadcast, show, broadcast
via cable, play in public, or rent copyrighted material without
permission.
This product features the copy protection function developed
by Macrovision. Copy protection signals are recorded on some
discs. When recording and playing the pictures of these discs
on a VCR, picture noise will appear.
This product incorporates copyright protection technology that
is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIAL NUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No. ____________DVC-2700_____________
Serial No. __________________________________
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL.
AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and operating instructions should be read before the product is
operated.
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the product.
11. Only use attachments/accessories specified by
the manufacturer.
3. Heed all warnings. - All warnings on the product and
in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this product near water. – For example:
near a bath tub, wash bowl, kitchen sink, laundry tub,
in a wet basement; or near a swimming pool; and
other areas located near water.
6. Clean only with dry cloth. – Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over- heating. The openings should never be blocked by placing the product
on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been
adhered to.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution
when moving the cart/product combination to
avoid injury from tip-over.
13. Unplug this product during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the product, the product
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
3
INTRODUCTION
IMPORTANT SAFETY INSTRUCTIONS
Table of Contents
Introduction
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13
Connecting Antenna/Cable TV to DVD+VCR . . . 11
Basic TV Connections . . . . . . . . . . . . . . . . . . . . 12
Optional, Preferred TV Connections . . . . . . . 12-13
Before Operation - VCR Part . . . . . . . . . . . . . . 14-16
On-Screen Display(OSD) . . . . . . . . . . . . . . . . . . 14
Setting the On-Screen Display . . . . . . . . . . . . . . 14
Setting the VCR Setup Menu . . . . . . . . . . . . . . . 15
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . 15
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . 16
Before Operation - DVD Part . . . . . . . . . . . . . . 17-20
General Explanation. . . . . . . . . . . . . . . . . . . . . . 17
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 17
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . 18-20
Initial Settings General Operation . . . . . . . . . 18
LANGUAGE. . . . . . . . . . . . . . . . . . . . . . . . . 18
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
LOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Operation with DVD . . . . . . . . . . . . . . . . . . . . . 27-29
Playing DVD . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
General Features . . . . . . . . . . . . . . . . . . . . . . . . 27
Moving to another TITLE . . . . . . . . . . . . . . . 27
Moving to another CHAPTER. . . . . . . . . . . . 27
Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 27
Still Picture and Frame-by-Frame Playback . 28
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Repeat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 28
Time Search . . . . . . . . . . . . . . . . . . . . . . . . 28
3D Surround . . . . . . . . . . . . . . . . . . . . . . . . 28
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Marker Search . . . . . . . . . . . . . . . . . . . . . . . 29
Special DVD Features . . . . . . . . . . . . . . . . . . . . 29
Checking the contents of DVD Video discs: Menus . 29
Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Camera Angle . . . . . . . . . . . . . . . . . . . . . . . 29
Changing the Audio Language . . . . . . . . . . . 29
Subtitles. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Operation with Audio CD and MP3 Discs . . . . 30-31
Playing an Audio CD and MP3 Discs . . . . . . . . . 30
Notes on MP3 Recordings . . . . . . . . . . . . . . . . . 30
Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Moving to another Track . . . . . . . . . . . . . . . 31
Repeat Track/ All/ Off. . . . . . . . . . . . . . . . . . 31
Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Random . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Repeat A-B . . . . . . . . . . . . . . . . . . . . . . . . . 31
Programmed Playback . . . . . . . . . . . . . . . . . . . . . 32
Programmed Playback with Audio CD
and MP3 Discs . . . . . . . . . . . . . . . . . . . . . . . . . 32
Repeat Programmed Tracks . . . . . . . . . . . . 32
Erasing a Track from Program List . . . . . . . . 32
Erasing the Complete Program List . . . . . . . 32
Operation
Reference
Operation with tape . . . . . . . . . . . . . . . . . . . . . 21-26
Normal Playback . . . . . . . . . . . . . . . . . . . . . . . . 21
Special Effect Playbacks . . . . . . . . . . . . . . . . . . 21
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Still Picture and Frame-by-Frame Playback . 21
Slow Motion . . . . . . . . . . . . . . . . . . . . . . . . . 21
Ad JUMP (Advertisement Jump). . . . . . . . . . 21
Normal Recording . . . . . . . . . . . . . . . . . . . . . . . 22
Timer Recording . . . . . . . . . . . . . . . . . . . . . . 22-23
Instant Timer Recording . . . . . . . . . . . . . . . . . . . 24
Dubbing and Editing. . . . . . . . . . . . . . . . . . . . . . 24
Copying from DVD to VCR. . . . . . . . . . . . . . . . . 24
VHS Hi-Fi Stereo System/MTS Broadcast . . . . . 25
Tape Counter Memory Feature. . . . . . . . . . . . . . 26
Additional Information . . . . . . . . . . . . . . . . . . . . 26
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 33-34
Language Code List . . . . . . . . . . . . . . . . . . . . . . . 35
Country Code List . . . . . . . . . . . . . . . . . . . . . . . . . 36
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . 3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Display Window. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Preparation
4
About the symbols for instructions
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
Before Use
Playable Discs
Title (DVD only)
The main film content or accompanying feature content
or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
Audio CD
(8 cm/12 cm disc)
In addition, this unit can play a CD-R or CD-RW that
contains audio titles or MP3 files.
Notes
– Depending on the conditions of the recording equipment or the CD-R/RW disc itself, some CD-R/RW
discs cannot be played on the unit.
– The unit cannot play discs that contain data other
than MP3 and CD-DA data.
– Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
– Do not use irregularly shaped CDs (e.g., heartshaped or octagonal). It may result in malfunctions.
Regional code of the DVD+VCR and DVDs
This DVD+VCR is designed and manufactured
for playback of region 1 encoded DVD software.
The region code on the labels of some DVD discs indicates which type of DVD+VCR can play those discs. This
unit can play only DVD discs labeled 1 or ALL. If you try
to play any other discs, the message “Check Regional
Code” will appear on the TV screen. Some DVD discs
may not have a region code label even though their playback is prohibited by area limits.
1
Note on DTS-encoded CDs
When playing DTS-encoded CDs, excessive noise may
be exhibited from the analog stereo output. To avoid
possible damage to the audio system, turn down the
volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy
DTS Digital SurroundTM playback, an external 5.1 channel Digital SurroundTM decoder system must be connected to the digital output of the unit.
Track (audio CD only)
Sections of a musical piece on an audio CD. Each track
is assigned a track number, enabling you to locate the
track you want.
Remote control battery installation
AAA
Notes on DVDs
Some playback operations of DVDs may be intention
ally fixed by software manufacturers. As this unit plays
DVDs according to disc content designed by the software manufacturer, some playback features of the unit
may not be available or other functions may be added.
Refer also to the instructions supplied with the DVDs.
Some DVDs made for business purposes may not be
played on the unit.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number to
enable you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
AAA
DVD
(8 cm/12 cm disc)
Detach the battery cover on the rear of the
remote control, and insert two R03 (size
AAA) batteries with
and
aligned
correctly.
Caution
Do not mix old and new batteries. Never mix different
types of batteries (standard, alkaline, etc.).
Remote Control Operation Range
Point the remote control at the remote sensor and press
the buttons.
Distance: About 23 ft (7 m) from the front of the
remote sensor
Angle: About 30° in each direction of the front of the
remote sensor
IMPORTANT NOTE:
SPENT OR DISCHARGED BATTERIES MUST BE
RECYCLED OR DISPOSED OF IN A SAFE MANNER
IN COMPLIANCE WITH ALL APPLICABLE LAWS.
FOR DETAILED INFORMATION, CONTACT YOUR
LOCAL COUNTY SOLID WASTE AUTHORITY.
Manufactured under license from Dolby Laboratories. Dolby
and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. Copyright
1992-1997 Dolby Laboratories. All rights reserved.
DTS and DTS Digital Out are trademarks of Digital Theater
Systems, Inc.
5
INTRODUCTION
Disc-related terms
Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packaged at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
Cleaning discs
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the center out.
Yes
No
To keep the surface clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for older vinyl records.
Cleaning the unit
About the
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVD+VCR is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty or
worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Notes on Discs
Handling discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
About Symbols
symbol display
“
” may appear on the TV screen during operation.
This icon means the function explained in this owner’s
manual is not available on that specific DVD video disc.
About the disc symbols for instructions
A section whose title has one of the following symbols are
applicable only to those discs represented by the symbol.
DVD DVDs
CD
Audio CDs.
MP3 MP3 Discs.
Setting the Output Source
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
• If you want to view output source of DVD deck:
Press DVD on the remote or DVD/VCR on the front panel
until DVD indicator in the display window lights and output
source of DVD deck is viewed on the TV screen.
• If you want to view output source of VCR deck:
Press VCR on the remote or DVD/VCR on the front panel
until VCR indicator in the display window lights and output
source of VCR deck is viewed on the TV screen.
Note
• If you insert a disc while the DVD+VCR is in the VCR
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature
increase inside the car.
6
mode, the DVD+VCR will switch to DVD mode
automatically.
• If you insert a cassette tape without an erasure
prevention tab intact while the DVD+VCR is in the
DVD mode, the DVD+VCR will switch to VCR mode
automatically.
Front Panel
Disc Tray (DVD deck)
Insert a disc here.
Z)
EJECT(Z
Ejects the tape in the VCR deck.
INTRODUCTION
v/V
V)
CHANNEL (v
To scan up or down through memorized channels.
Cassette Compartment (VCR deck)
Insert a video cassette here.
Remote Sensor
Point the DVD+VCR remote control here.
Display window
Shows the current status of the DVD+VCR.
Z)
OPEN/CLOSE (Z
Opens or closes the disc tray.
B)
PLAY (B
Starts playback of a tape in
the VCR deck.
DVD/VCR indicator
Indicates the active deck.
x)
STOP (x
Stops playback of disc.
z)
REC (z
To record normally or to activate
Instant Timer Recording.
B)
PLAY (B
Starts playback of a disc
in the DVD deck.
X)
PAUSE/STILL(X
Pause playback of a disc in the DVD
deck temporarily/press repeatedly
for frame-by-frame playback.
DVD/VCR (output select)
Select one of your output sources to
view on the TV screen between DVD
and VCR.
POWER
Switches the DVD+VCR ON and OFF.
x)
STOP (x
Stops playback of tape.
AV INPUT (VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an
external source (Audio system,
TV/Monitor, Another VCR).
Child Lock
The control buttons on the front panel of the DVD+VCR
can be switched off so that your DVD+VCR can only be
operated using the remote control.
Press SAFE on the remote control to enable LOCK function, SAFE appears in the display window.
To disable the LOCK function, press SAFE on the remote
control until OFF appears in the display window.
7
Display Window
The DVD deck is selected.
A disc is in the DVD deck.
(Lights when a disc is in the DVD deck
and Flashes when no disc.)
Indicates repeat mode.
DVD to VCR copy is in progress.
DVD+VCR is in timer recording or a timer
recording is programmed.(VCR part only)
A cassette is in the VCR deck.
The VCR deck is selected.
DVD
COPY
VCR
REC
PM
TV
Lights when TV mode is active (See page 22.)
Indicates PM time. (AM is not displayed.)
DVD+VCR is Recording.
(VCR part only)
Indicates total playing time, elapsed time, remaining time or
current deck status (Playback, Pause, etc).
8
Remote Control
POWER
Switches DVD+VCR ON and OFF.
TV/VCR
To view channels selected by the VCR
tuner or by the TV tuner.
DISPLAY, CLK/CNT
Accesses On-Screen display.
Switches among the clock, tape counter
and tape remaining modes on the display.
b/B/v/V (left/right/up/down)
- Selects an option in the menu
- CH/TRK (v/V): Selects channel of VCR.
Adjusts manually the tape’s picture
onscreen.
SETUP, MENU
Accesses or removes DVD setup menu
and VCR menu.
TITLE
Displays the disc’s Title menu, if
available.
X)
PAUSE/STEP (X
Pause playback or recording
temporarily/press repeatedly for frameby-frame playback.
x)
STOP (x
Stops playback.
z)
REC (z
Records normally or activates Instant
Timer Recording.
0-9 numerical buttons
Selects numbered options in a menu.
AUDIO
Selects an audio language (DVD) or an
audio channel (CD).
SUBTITLE
Selects a subtitle language.
MARKER
Marks any point during playback.
SEARCH
Displays MARKER SEARCH menu.
REPEAT
Z)
OPEN/CLOSE, EJECT (Z
- Opens and closes the disc tray.
- Ejects the tape in the VCR deck.
SELECT/ENTER
- Acknowledges menu selection.
- Displays functions on the TV screen.
This button is not available.
DISC MENU
Accesses menu on a DVD disc.
INPUT
To select the VCR deck’s source (Tuner,
LINE 1, or LINE 2).
>)
FORWARD (>
DVD; Search forward*/go to next chapter or track.
VCR; Advances the tape during the
STOP mode or for fast forward picture
search.
H)
PLAY (H
Starts playback.
.)
BACKWARD (.
DVD; Search backward*/go to beginning
of current chapter or track or go to previous chapter or track.
VCR; Rewinds the tape during the
STOP mode or for fast reverse picture
search.
* Press and hold button for about two
seconds.
PROGRAM
Accesses or removes Program menu.
CLEAR
Removes a track number on the
program menu or a mark on the
MARKER SEARCH menu.
SAFE
Switch the Lock function on and off.
ANGLE
Selects a DVD camera angle if
available.
RETURN
Removes the setup menu.
ZOOM
Enlarges DVD video image.
Repeat chapter, track, title, all.
RANDOM, Ad JUMP
- Plays tracks in random order.
- Fast forwards picture search through
30 seconds of recording.
A-B, SP/SLP
- Repeats sequence.
- Selects recording speed
Note
This remote control use the same buttons for VCR and DVD
functions (ex. PLAY).
When using a VCR, first press the VCR button.
When using a DVD, first press the DVD button.
9
INTRODUCTION
DVD/VCR select button
Select the output source (DVD or VCR)
to view on the TV screen.
Rear Panel
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
Connect to a TV with video and audio inputs.
VCR IN LINE 1
(VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an external
source (Audio system, TV/Monitor,
Another VCR).
COMPONENT/PROGRESSIVE SCAN
VIDEO OUT (Y Pb Pr) (DVD OUT)
Connect to a TV with Y Pb Pr inputs.
AUDIO OUT (Left/Right) (DVD OUT)
Connect to a TV, amplifier, receiver, or stereo system.
S-VIDEO OUT (DVD OUT)
Connect to a S-Video Input on TV.
AC Power Cord
Plug into the power source.
DIGITAL AUDIO OUT (COAXIAL) (DVD OUT)
Connect to digital (coaxial) audio equipment.
RF. OUT(DVD/VCR OUT)
Connect to a TV with RF coaxial inputs.
ANT.IN(ANTENNA INPUT)
Connect the VHF/UHF/CATV antenna to this terminal.
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
10
Connections
Depending on your TV and other equipment you wish to
connect, there are various ways you could connect the
DVD+VCR. Use connections described on pages 11-13.
Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the best
connections.
For better sound reproduction, connect the DVD+VCR’s
DVD/VCR AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo or audio/video equipment. See
Optional, Preferred TV Connections on pages 12-13.
Caution
Make sure the DVD+VCR is connected directly to the TV.
Tune the TV to the correct video input channel.
Do not connect the DVD+VCR’s DVD/VCR AUDIO OUT
jacks to the phono in jack (record deck) of your audio
system.
Do not connect your DVD+VCR via your VCR. The DVD
image could be distorted by the copy protection system.
Connecting Antenna/Cable TV to
DVD+VCR
the antenna leads from the rear of the
1 Disconnect
TV.
the type of cable from your antenna. If it is
2 Identify
a round cable as illustrated, it is a 75 ohm coaxial
antenna cable. This cable will connect directly to
If your cable wire is connected to your TV without a converter
or descrambler box, unscrew the wire from your TV and attach
it to the ANT.IN jack on the DVD+VCR. Use the supplied round
coaxial cable to connect between the DVD+VCR’s RF.OUT
jack and the 75 ohm antenna input jack on the TV. With this
connection, you can receive all midband, super band, and
hyperband channels.
With Cable Box
If a converter is required in your cable system, follow the
instruction below:
The cable hookup permits both TV and DVD+VCR operation.
To view or record CATV channel
1 Tune the TV to the DVD+VCR output channel (CH 3 or 4).
2 Set the DVD+VCR channel selector to the output channel of
the Cable Converter box by pressing the CH/TRK (v/V) or
number (0-9) of your DVD+VCR. (Example: CH3)
3 Select the channel to view at the Cable Converter Box.
Notes
With this connection, you CANNOT record one program
while viewing another.
If you are using a cable box to tune channels, it is not necessary to do Auto Channel Programming as indicated on
page 15.
Cable TV
Wall Jack
Back Panel of
Typical Cable Box
the jack marked ANT.IN on your DVD+VCR.
Tip
If your antenna lead wire is a flat type antenna cable,
connect it to a Antenna Adaptor (300-ohm to 75-ohm)
(not supplied) and slip the Adaptor onto the ANT.IN
jack. The Adaptor does not screw on to the DVD+VCR,
it just slips over the jack.
Antenna
Antenna
Cable TV
Wall Jack
Flat Wire
(300 ohm)
Rear of DVD+VCR
300/75 ohm
Adaptor
(Not supplied)
OR
OR
Rear of DVD+VCR
11
PREPARATION
Without Cable Box
Tips
Connections (Continued)
Basic TV Connections
Optional, Preferred TV Connections
Make one of the following connections, depending on
the capabilities of your existing equipment.
RF coaxial connection
Connect the RF.OUT jack on the DVD+VCR to the
antenna in jack on the TV using the 75-ohm Coaxial
Cable supplied (R).
Note
If you use this connection, tune the TV to the
DVD+VCR’s RF output channel (CH 3 or 4).
How to set the DVD+VCR’s RF output channel
1. When the DVD+VCR is turned off, press and hold
CHANNEL (v/V) on the front panel for about five
seconds.
Note
You can ONLY watch and listen to DVD playback
through the connections shown below.
S-Video connection
the S-VIDEO OUT jack on the DVD+VCR
1 Connect
to the S-Video in jack on the TV using the optional
S-Video cable (S).
the Left and Right AUDIO OUT jacks of
2 Connect
the DVD+VCR to the audio left/right in jacks on the
TV using the supplied audio cables (A2).
Component Video (Color Stream®) / Progressive
Scan (ColorStream® pro) connection
It will turn itself on and “RF03” or “RF04” appears in the display window.
2. Press CHANNEL (v/V) on the front panel or CH/TRK
(v/V) on the remote control to change the RF output
channel (CH 03 or CH 04).
3. Turn off the DVD+VCR.
Audio/Video connection
1
Connect the DVD/VCR VIDEO OUT jack on the
DVD+VCR to the video in jack on the TV using the
video cable supplied (V).
the Left and Right DVD/VCR AUDIO OUT
2 Connect
jacks on the DVD+VCR to the audio left/right in
jacks on the TV (A1) using the supplied audio
cables.
Note
If you use this connection, set the TV’s source selector
to VIDEO.
Rear of TV
ANTENNA
INPUT
AUDIO INPUT
L
R
Rear of DVD+VCR
12
A1
1
If your television is a high-definition or “digital ready”
television, you may take advantage of the
DVD+VCR’s progressive scan output for the highest
video resolution possible.
If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try
Progressive Scan on the DVD+VCR.
2
Connect the COMPONENT / PROGRESSIVE
SCAN VIDEO OUT jacks on the DVD+VCR to the
corresponding in jacks on the TV using an optional
Y Pb Pr cable (C).
Connect the Left and Right AUDIO OUT jacks of
the DVD+VCR to the audio left/right in jacks on the
TV (A2) using the supplied audio cables.
Notes
– Set the Progressive Scan to “On” on the setup menu
for progressive scan signal, see page 18.
– When you use Component Video signal, set the
Progressive Scan to “Off” on the setup menu.
– Progressive scan does not work with the analog video
connections (yellow VIDEO OUT jack).
Rear of TV
VIDEO
INPUT
S-VIDEO
INPUT
COMPONENT / PROGRESSIVE SCAN
VIDEO INPUT
Pr
R
V
S
C
Rear of DVD+VCR
Pb
AUDIO INPUT
Y
R
A2
L
Connections (Continued)
Optional, Preferred TV Connections
Rear of DVD+VCR
PREPARATION
(Continued)
Note
You can ONLY listen to DVD playback using COAXIAL
(X) and AUDIO OUT (A2) connections. The tuner and
VCR will still be heard through the RF.OUT (R) or
DVD/VCR AUDIO OUT (A1) jacks. (See page 12.)
Connecting to an amplifier equipped with two
channel analog stereo or Dolby Surround
A1
A2
X
Connect the Left and Right AUDIO OUT (or DVD/VCR
AUDIO OUT) jacks on the DVD+VCR to the audio left
and right in jacks on your amplifier, receiver, or stereo
system using the audio cables (A1, A2) supplied.
L
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an Audio/Video
receiver equipped with a multi-channel decoder
(Dolby Digital™, MPEG 2, or DTS)
1
Connect one of the DVD+VCR’s DIGITAL AUDIO
OUT jacks (COAXIAL X) to the corresponding in
jack on your amplifier. Use an optional digital
(coaxial X) audio cable.
will need to activate the DVD+VCR’s digital
2 You
output. (See “AUDIO” on page 19).
R
DIGITAL INPUT
Amplifier (Receiver)
Accessory Audio/Video (A/V) Connections to
DVD+VCR
Connect the VCR IN LINE 1 or AV INPUT jacks on the
DVD+VCR to the audio/video out jacks on your
accessory component, using the optional audio/video
cables.
Accessory Component:
VCR, Camcorder,
Video Camera,
Satellite Receiver,
Laser Disc Player
Digital Multi-channel sound
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of the
audio formats supported by your DVD+VCR (MPEG 2,
Dolby Digital and DTS). Check the receiver manual and
the logos on the front of the receiver.
COAXIAL
AUDIO INPUT
Jack panel of Accessory
AUDIO
OUTPUT
R
L
Caution:
Due to the DTS Licensing agreement, the digital output
will be in DTS digital out when DTS audio stream is
selected.
Notes
– If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will
produce a strong, distorted sound or no sound at all.
– Six Channel Digital Surround Sound via digital
connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
– To see the audio format of the current DVD in the
on-screen display, press AUDIO.
VIDEO
OUTPUT
OR
Rear of DVD+VCR
Front of DVD+VCR
13
Before Operation - VCR Part
On-Screen Display (OSD)
Some of these functions will be displayed every time the
VCR is operated.
❶
❷
❸
PLAY
SP
HI-FI
JUL 5 , SAT
❹
❺
CH 4
STEREO
2:15 PM
❻
❶ TAPE SPEED DISPLAY
❼
Shows the current tape speed.
❷ FUNCTION DISPLAY
Indicates the function in progress.
❸ HI-FI DISPLAY
Indicates when this unit is playing back tape recorded with
Hi-Fi.
❹ CHANNEL DISPLAY
Indicates the selected channel (or LINE1, LINE2).
❺ STEREO/SAP DISPLAY (MONO is not displayed)
Shows the type of audio signal received by the VCR tuner.
❻ DATE DISPLAY
Shows the current date. (Month/Date/Day of the week
format)
❼ CLOCK/COUNT/REMAIN DISPLAY
Shows the current time, the tape counter and remaining time
on the tape.
Each press of the SELECT/ENTER changes the TV
screen in the following sequence.
STOP
SP
CH 4
STEREO
EASY INFORMATION
If the Extended Data Service (XDS) signals are provided
along with normal TV signal in your area or during playback of a tape recorded with Extended Data Service
(XDS) signals, the station ID, program title and program
details are shown in the TV screen.
When viewing a channel with Extended Data Service (XDS)
signals, press SELECT/ENTER then the station ID will
appear on the TV screen. Press SELECT/ENTER again
and the program details will appear on the TV screen.
When viewing a tape recorded with Extended Data
Service (XDS) signals, press SELECT/ENTER twice
then the program title and program details will appear
on the TV screen.
PROGRAM DETAILS
LENGTH: Indicates the run length of a program.
TIME REMAINING: Indicates the remaining time of a
program.
RATING: Indicates the rating of the current program
(N/A, G, PG, PG-13, R, NC-17, X and Not Rated). The
rating N/A means that the motion picture ratings are not
applicable to this program.
SP
CH 4
WABC STEREO
“Home video”
JUL 5 , SAT
2:15 PM
Easy Information Screen
(Station ID)
PROGRAM DETAILS
“Home video”
LENGTH 01:00
TIME REMAINING 00:26
RATING N/A
Easy Information Screen
(Program details)
Setting the On-Screen Display
The SETUP, clock setting, and timer recordings are
accessed conveniently with On-Screen Menu Displays
that lead you through each step. The following pages
describe the On-screen selections to be set.
Menu Selection
JUL 5 , SAT
Your VCR allows remote control adjustment of several
features.
Press MENU and the MAIN menu will appear.
2:15 PM
2:15 PM
0:35:40
REM 1:58
Notes
The function displays can be seen displayed on the TV
screen for 5 seconds.
The clock (or tape counter, tape remaining) mode will continue until you press SELECT/ENTER.
The tape counter and the remaining tape length indicator
appear only when a cassette is inserted. Also, the remaining
tape length indicator appears after any tape operation.
1
Select the desired menu with v/V button and
2 then
press SELECT/ENTER.
Note
Menus remain on-screen for 3 minutes.
MAIN MENU
CLOCK SET (page 16)
PROGRAM (page 22)
TUNING (page 15)
SETUP (page 15)
3 Press MENU when finished.
14
Setting the VCR Setup Menu
Channel Selection
1 Press MENU and the MAIN menu will appear.
v/V
V to select the SETUP menu, then
2 Press
press SELECT/ENTER.
The SETUP menu will appear.
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Preparation:
Connect the DVD+VCR to the desired type of antenna or
cable TV system, as shown in Connecting Antenna/Cable TV
to DVD+VCR on page 11.
AUTO CHANNEL PROGRAMMING
v/V
V to choose a desired option on the
3 Press
B to choose a
SETUP menu. Then press b/B
desired setting.
1 Press MENU and the MAIN menu will appear.
v/V
V to select the TUNING menu, then
2 Press
press SELECT/ENTER.
The TUNING menu will appear.
FUNCTION OSD
The on-screen display of this DVD+VCR can be turned on or off.
FUNCTION OSD can be switched between ON and OFF by
pressing b/B.
LANGUAGE SELECT
The on-screen programming of this DVD+VCR can be
displayed in either English, Spanish, or French.
LANGUAGE SELECT can be switched among ENGLISH,
SPANISH and FRENCH by pressing b/B.
AUDIO MODE
The DVD+VCR has two separate audio playback systems, the
high quality VHS Hi-Fi system and standard NORMAL mono
system. The same audio is generally recorded on both
systems. The VHS Hi-Fi system plays on separate (left and
right) channels, and the NORMAL system plays monaural
sound. The normal track is always played so the cassette can
be played on a DVD+VCR that does not have VHS Hi-Fi.
AUDIO MODE can be switched between HI-FI and
NORMAL by pressing b/B.
BROADCAST TYPE (STEREO/SAP/MONO)
Multichannel Television Sound (MTS) carries stereo and/or
Second Audio Program (SAP) bilingual signals. Set this display to
the desired position when both MTS stereo and SAP signals are
received. When only one of the MTS signal is received, the
DVD+VCR automatically selects the corresponding receiving
mode (Stereo or SAP) regardless of the selected position. For
normal operation, the display should be in the STEREO position.
The DVD+VCR will then record a STEREO program when available,
and record a mono program IF the program is NOT IN STEREO.
For weak STEREO and/or SAP broadcasts, changing the display to mono may give clearer sound.
BROADCAST TYPE can be switched among STEREO, SAP,
and MONO by pressing b/B.
AUDIO OUTPUT (STEREO/LEFT/RIGHT)
Used during playback [when AUDIO MODE (HI-FI/NORMAL) is
in HI-FI position] for selecting the audio output signals from the
AUDIO OUT terminals (L ch and R ch), and RF.OUT.
This display setting should normally be left in the stereo position, so that when a stereo tape is played, the stereo sound will
be heard through the left and right channels. If a mono tape is
played and the audio output is set to stereo, the same mono
sound will be heard from both left and right channels.
AUDIO OUTPUT can be switched among STEREO, LEFT,
and RIGHT by pressing b/B.
4
Press MENU when finished.
V to choose the SOURCE SELECT option,
3 Press
B to select TUNER.
then press b/B
Press b/B repeatedly to switch among TUNER, LINE1
and LINE2.
v/V
V to choose the AUTO CHANNEL SET
4 Press
B to set the channel.
option, then press b/B
The tuner will automatically cycle through all
available channels in the area and place them in
the tuner’s memory.
the AUTO CHANNEL SET PROCEEDING is
5 After
complete, make sure the TUNING BAND is set
V and
appropriately (TV or CATV) by pressing v/V
choosing the correct TUNING BAND (TV or
B using the TUNING
CATV) by pressing b/B
menu.
Remember, TV is for the air antenna reception,
CATV is for cable or wireless cable connection.
6 Press MENU to return to the TV screen.
v/V
V) or CHANNEL (v
v/V
V) on the
CH/TRK (v
7 Use
front panel to cycle the DVD+VCR through the
channels in memory.
TO ADD OR ERASE CHANNELS FROM MEMORY
This feature allows you to add or erase channels from
memory manually.
1
Press V to choose the CH. ADD/DEL option on the
TUNING menu. Press b/B to select a channel to
add or erase.
2
Press SELECT/ENTER to add or erase the channel.
Repeat steps 1 and 2 to add or erase channels.
3
Press MENU to return to the TV screen.
15
PREPARATION
Before Operation - VCR Part (Continued)
Before Operation - VCR Part (Continued)
Setting the Clock
The DVD+VCR gives you two ways to set the time and
date: the Auto Clock Feature or manually. The Auto
Clock Feature enables the DVD+VCR to set up the clock
when the DVD+VCR is turned off.
Things to know before starting
The clock uses the 12-hour system. (Be sure to set AM
and PM correctly.)
The initial Clock Setting is JANUARY 1, 2003, 12:00 AM.
Auto Clock Set
The Auto Clock Set feature is set to ON at the factory. In the
ON setting, the DVD+VCR looks for a channel carrying XDS
(Extended Data Services) information. XDS updates the clock
using the Coordinated Universal Time.
Note
There are cases where the TV station does not send or sends
wrong date and/or time information and the DVD+VCR sets the
incorrect time.
If this happens we recommend that you set the clock manually.
Manual Clock Set
Example: JULY 5, 2003 ; 2:15 AM
1 Press MENU and the MAIN menu will appear.
v/V
V to choose the CLOCK menu.
2 Press
Press SELECT/ENTER and the CLOCK menu
will appear.
The Auto Clock Feature enables the DVD+VCR to set up
the clock when the DVD+VCR is turned off.
1 Press MENU and the MAIN menu will appear.
v/V
V to choose the CLOCK menu.
2 Press
Press SELECT/ENTER and the CLOCK menu
will appear.
3 Press b/BB to choose the month.
V to choose the DAY option.
4 Press
B to choose the day.
Use b/B
The day of the week will display automatically.
V to choose the AUTO CLOCK SET option.
3 Press
B to choose ON.
Press b/B
The Auto Clock Set feature is set to ON at the factory. In
the ON setting, the DVD+VCR looks for a channel
carrying XDS (Extended Data Services) information. XDS
updates the clock using the Coordinated Universal Time.
Press
4 item.
Press
E
to choose the DAYLIGHT SAVINGS
F
or
G
V to choose the YEAR option.
5 Press
B to choose the year.
Use b/B
Press V to choose the TIME option.
6 Use b/BB to choose the time.
Press to choose the DAYLIGHT SAVINGS
7 item.
E
Press
F
or
G
to choose AUTO, ON or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR sets the clock when the
Daylight Saving Time is started and ended.
to choose AUTO, ON or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR sets the clock when the
Daylight Saving Time is started and ended.
Press
5 Press
to choose the TIME ZONE item.
or G to choose the correct time zone
(AUTO, EASTERN, CENTRAL, MOUNTAIN,
PACIFIC, ALASKA or HAWAII).
E
F
If “AUTO” is selected as the time zone, the VCR sets the
clock using the first Coordinated Universal Time information it finds in a broadcast signal.
6
off the DVD+VCR and the auto clock
7 Turn
setting works.
Press MENU when finished.
16
8 Press MENU when finished.
Note
If setting the clock manually, “AUTO CLOCK SET” must
set to “OFF”.
If set to “ON”, an incorrect date and/or time will be
entered again when the DVD+VCR is turned off.
Before Operation - DVD Part
b/B to change the setting of an item.
3 Use
The number buttons can be also be used for setting
numbers (e.g., title number). For some functions,
press SELECT/ENTER to execute the setting.
PREPARATION
Caution:
Before using the remote control, press the DVD button
to select the device to be operated.
Temporary Feedback Field Icons
General Explanation
This manual gives basic instructions for operating the
DVD+VCR. Some DVDs require specific operation or
allow only limited operation during playback. When this
occurs, the symbol
appears on the TV screen, indicating that the operation is not permitted by the
DVD+VCR or is not available on the disc.
On-Screen Display
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
On-screen display operation
1 Press DISPLAY during playback.
Use v/V to select an item.
2 The
selected item will be highlighted.
Title
Chapter
A-B
Off
Repeat Title (DVD)
Repeat Chapter (DVD)
Repeat A-B
Repeat Off
Resume play from this point
Action prohibited or not available
Notes
Some discs may not provide all of the features on the
on-screen display example shown below.
If no button is pressed for 10 seconds, the on-screen
display disappears.
You can change the desired status only when “b B”
mark appears on the On-screen display menu item.
DVD
Items
Title Number
1/3
Chapter Number
1 / 12
Time search
Audio language
and Digital Audio
Output mode
Subtitle language
Angle
Sound
0:20:09
1 ENG
D
5.1 CH
ABC
1 ENG
1/1
3D SUR
Function (Use v/V to select desired item)
Selection Method
Shows the current title number and total number of
titles, and skips to the desired title number.
b / B, or
Numbers, SELECT/ENTER
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
b / B, or
Numbers, SELECT/ENTER
Shows the elapsed playing time, and
searches the point by the elapsed time directly.
Numbers, SELECT/ENTER
Shows the current audio soundtrack language,
encoding method, and channel number, and
changes the setting.
Shows the current subtitles language, and
changes the setting.
Shows the current angle number and total number of
angles, and changes the angle number.
Shows the current sound mode, and
changes the setting.
b / B, or
AUDIO
b / B, or
SUBTITLE
b / B, or
ANGLE
b/B
17
Before Operation - DVD Part (Continued)
Initial Settings
Disc Language (Audio, Subtitle, Menu)
In this menu system, there are several ways to customize the settings provided. Most menus consist of
three levels to set up the options, but some require
greater depth for the variety of settings. If you press
SETUP, only the first level of the menu system will
appear on the TV screen. The second and third level
can be displayed by pressing B. For navigating the
menu levels, you will see “ B “ on the right side of the
menu label to help you to go to the next level.
DVD
Select a language for the disc’s Audio, Subtitle, and
Menu.
Original : The original language set for the disc is selected.
Other : To select another language, press number buttons to
enter the corresponding 4-digit number according to the language code list on page 35. If you enter the wrong language
code, press CLEAR.
DISPLAY
DISPLAY
To bring up and exit the Menu:
Press the SETUP to bring up the menu. The second
press of SETUP will take you back to initial screen.
TV Aspect
16 : 9
Display Mode
Widescreen
Progressive Scan
Off
To go to the next level:
Press B on the remote control.
Move
To go back to the previous level:
Press b on the remote control.
TV Aspect
Initial Settings General Operation
1
Press SETUP.
The setup menu appears. The screen will show the
current setting for the selected item.
2 Use v/V to select the desired item.
the desired item is selected, press B to
3 While
move to the second level.
4 Use v/V to select the second desired item.
5 Press B to move to the third level.
v/V to select the desired setting then
6 Press
press SELECT/ENTER to confirm your selection.
Some items require additional steps.
7
Press SETUP to exit the setup menu.
LANGUAGE
Select
DVD
4:3: Select when a standard 4:3 TV is connected.
16:9: Select when a 16:9 wide TV is connected.
Display Mode
DVD
The Display Mode setting works only when the TV
Aspect mode is set to “4:3”.
Letterbox: Displays theatrical images with masking
bars above and below the picture.
Panscan: Select when a conventional TV set is connected. The video material formatted in the Pan & Scan
style is played back in that style (Both sides of the picture are cut off).
Progressive Scan
DVD
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT jacks, but are connecting the
DVD+VCR to a standard (analog) television, set
Progressive Scan to Off.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
LANGUAGE
Menu Language
English
Disc Audio
Original
Disc Subtitle
Off
Disc Menu
Original
Move
Select
Menu Language
Select a language for the setup menu and information
display.
18
Caution
Once the setting for progressive scan output is entered,
“Select Enter to confirm and press SELECT/ENTER
key.” appears. Use b B button to select “Enter” and
press SELECT/ENTER button. An image will be visible
only on a progressive scan compatible TV or monitor. If
you set Progressive Scan to “On” in error when this
DVD+VCR is connected to the standard (analog) TV,
the picture will appear scrambled. After ten seconds, the
video output will be restored to the standard setting,
and a picture will be visible on a conventional analog
TV or monitor again.
Before Operation - DVD Part (Continued)
AUDIO
Each DVD disc has a variety of audio output options.
Set the player’s Audio Output according to the type of
audio system you use.
AUDIO
Dolby Digital
Bitstream
DTS
Bitstream
MPEG
PCM
Sample Freq.
48 kHz
DRC
On
Vocal
On
With the DVD format, you can hear a program’s soundtrack in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing clarity of sound. Set
DRC to “On” for this effect.
Vocal
Move
Select
Dolby Digital
Bitstream: Select “Bitstream” if you connected the
DVD+VCR’s DIGITAL OUT jack to a Dolby Digital
decoder (or an amplifier or other equipment with a
Dolby Digital decoder).
PCM: Select when connected to a two-channel digital
stereo amplifier. DVDs encoded in Dolby Digital will be
automatically downmixed to two-channel PCM audio.
Set Vocal to “On” only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
OTHERS
The PBC and Auto Play settings can be changed.
OTHERS
PBC
On
AutoPlay
Off
DTS
Bitstream: Select “Bitstream” if you connected the
DVD+VCR’s DIGITAL OUT jack to a DTS decoder (or
an amplifier or other equipment with a DTS decoder).
Off: If you select “Off”, the DTS signal through the DIGITAL OUT jack is not outputted.
MPEG
Bitstream: Select “MPEG” if you connected the
DVD+VCR’s DIGITAL OUT jack to a MPEG decoder (or
an amplifier or other equipment with a MPEG decoder).
PCM: Select when connected to a 2-channel digital
stereo amplifier. The DVD+VCR outputs sounds in the
PCM 2ch format when you play a DVD video disc
recorded on the MPEG1, or MPEG2 recording system.
Sample Freq. (Frequency)
To change the Sample Frequency setting, first select
the desired Dolby Digital, DTS, and MPEG mode as
indicated as above.
If your receiver or amplifier is NOT capable of handling
96 kHz signals, select 48 kHz. When this choice is
made, this unit will automatically convert any 96 kHz
signals to 48 kHz, so your system can decode them.
If your receiver or amplifier is capable of handling
96 kHz signals, select 96 kHz. When this choice is
made, this unit will pass through each type of signal
without any further processing.
Move
Select
PBC
Set Playback Control (PBC) to “On” or “Off”.
On: Video CDs with PBC are played according to the PBC.
Off: Video CDs with PBC are played the same way as Audio
CDs.
Auto Play
DVD
You can set up the DVD+VCR so a DVD disc automatically starts playing whenever the DVD is inserted.
If Auto Play mode is set to “On”, this DVD+VCR will
search the title which playback time is the longest and
then play back the title automatically.
On: Auto Play function is activated.
Off: Auto Play function is not activated.
Note
The Auto Play function may not work for some DVDs.
19
PREPARATION
Dynamic Range Control (DRC)
Before Operation - DVD Part (Continued)
3 While “New” is selected, press SELECT/ENTER.
a 4-digit password using the numbered
4 Enter
buttons to create a personal 4-digit security
password then press SELECT/ENTER.
LOCK
LOCK
Rating
Unlock
Password
New
Country Code
CA
Tip
If you make a mistake before pressing
SELECT/ENTER, press CLEAR to delete the entered
all-digit or press b to delete one by one and correct it.
Move
Rating
Select
DVD
Movies on DVDs may contain scenes not suitable for
children. Therefore, discs may contain Parental Control
information that applies to the complete disc or to
certain scenes on the disc. These scenes are rated
from 1 to 8, and alternatively, more suitable scenes are
available for selection on some discs. Ratings are different in each country. The Parental Control feature allows
you to prevent discs from being played by your children
or to have certain discs played with alternative scenes.
1 Select “Rating” on the Setup menu.
2 While “Rating” is selected, press B.
When you have already entered a password
Enter a 4-digit password using the numbered buttons to
confirm the personal 4-digit security password, then
press SELECT/ENTER.
a rating from 1 to 8 using the v/V but3 Select
tons. One (1) has the least playback restrictions.
Eight (8) has the most playback restrictions.
Unlock: If you select Unlock, Parental Control is
not active. The disc will play in full.
Ratings 1 to 8: Some discs contain scenes not
suitable for children. If you set a rating for the player, all disc scenes with the same rating or lower will
be played. Higher rated scenes will not be played
unless an alternative scene is available on the disc.
The alternative must have the same rating or the
lower one. If no suitable alternative is found, playback will stop. You must enter the 4-digit password
or change the rating level in order to play the disc.
4
Press SELECT/ENTER to confirm your rating
selection, then press SETUP to exit the menu.
Password DVD
Setting your password
If you change the rating level to “7” or lower, you must
enter a 4-digit “password” to prevent playback of discs
with higher ratings.
1 Select “Password” on the Setup menu.
2 While “Password” is selected, press B.
20
the 4-digit password again and press
5 Enter
SELECT/ENTER to verify.
Changing the 4-digit password
1 Follow Steps 1-2 as shown above (Setting your
password).
2 Enter the old password, then press SELECT/ENTER.
3 Select “Change” using v/V buttons then press
SELECT/ENTER.
4 Enter the new 4-digit password, then press
SELECT/ENTER.
5 Enter the 4-digit password again and press
SELECT/ENTER to verify.
If you forget your 4-digit password
If you forget your password, to clear the current password, follow the procedure below.
1 Press SETUP to display the setup menu.
2 Use the Number buttons to enter the 6-digit number
“210499”.
3 Enter a new code as shown above (Setting your
password).
Country Code
DVD
Enter the code of a country/area which standards were
used to rate the DVD video disc, referring to the list
(See “Country Code List”, page 36.).
1 Select “Country Code” on the Setup menu.
2 While “Country Code” is selected, press B.
When you have already entered a password
Enter a 4-digit password using the numbered buttons to
confirm the personal 4-digit security password, then
press SELECT/ENTER.
3 Select the first character using the v/V buttons.
the cursor using B button and select the
4 Shift
second character using v/V buttons.
SELECT/ENTER to confirm your country
5 Press
code selection, then press SETUP to exit the
menu.
Normal Playback
Search
Preparation:
This function lets you search for a desired tape section
in either direction: forward or reverse quickly and visually.
Turn on the TV.
Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
Set the Output Source to VCR as shown in “Setting the
Output Source” on page 6.
1
Insert a prerecorded video cassette.
The
indicator will light and the DVD+VCR will
power-up automatically.
Make sure that the
indicator in the display
window is not lighted. If it is, press POWER once.
If a tape without a safety tab is inserted, the unit will
start playback automatically.
H) once.
PLAY (H
2 Press
PLAY appears on the TV screen .
It is not necessary to select the tape speed for playback. It will be automatically selected by the DVD+VCR.
During playback, the TV/VCR selector switches to VCR
mode automatically.
x) to stop playback.
Press STOP (x
3 STOP
appears on the TV screen.
If the tape reaches the end before STOP (x) is
pressed, the DVD+VCR will automatically stop, rewind,
eject, and will turn itself off (Only when no disc).
Tracking Control
Auto Tracking
The automatic tracking function adjusts the picture to
remove snow or streaks.
The AUTO TRACKING function works in the following
cases:
A tape is played back for the first time.
Tape speed (SP, LP, SLP) changes.
Streaks or snow appear because of scratches on the tape.
Manual Tracking
If noise appears on the screen during playback, press
v/V
V) on the remote control or
either CH/TRK (v
v/V
V) on the front panel until the noise on
CHANNEL (v
the screen is reduced.
In case of vertical tremble, adjust these controls very carefully.
Tracking is automatically reset to normal when the tape is
ejected or the power cord is unplugged for more than 3 seconds.
Special Effect Playbacks
1 Press BACKWARD (.) or FORWARD (>)
during playback.
The DVD+VCR will be activated in the SEARCH
mode.
If the DVD+VCR is left in the SEARCH mode for more
than 3 minutes, the DVD+VCR will automatically enter the
PLAY mode, to protect the tape and video heads.
2 To return to playback, press PLAY (H).
Still Picture and Frame-by-Frame Playback
1 Press PAUSE/STEP (X) during playback.
Still picture will appear on the TV screen.
If a still picture vibrates vertically, stabilize it by pressing
CH/TRK (v/V) on the remote control.
If the DVD+VCR is left in the STILL mode for more than 5
minutes, the DVD+VCR will automatically enter the STOP
mode to protect the tape and video heads.
2 Press PAUSE/STEP (X) repeatedly to advance the
video picture one frame at a time while viewing a still
picture.
3 To return to playback, press PLAY (H).
Slow Motion
1 During the still mode, press FORWARD (>).
The tape will be played back at a speed 1/19 times
slower than the normal speed.
During slow playback, use CH/TRK (v/V) on the Remote
Control to minimize noise bands.
If slow motion mode continues for more than 3 minutes,
the DVD+VCR will automatically change to playback
mode.
2 To return to playback, press PLAY (H).
Ad JUMP (Advertisement Jump)
This is useful for skipping commercials or short program
segments.
1 Press Ad JUMP during the playback mode.
The tape will be fast forward picture search through
30 seconds of recording.
The skipping time can be extended by pressing Ad JUMP.
Subsequent presses result in advancing the fast forward
picture search time by 30-second increments (maximum 3
minutes).
2 When the search is completed, the DVD+VCR will go
into playback mode automatically.
Special effects playback notes
Horizontal lines (noise bars) will appear on the TV screen. This
is normal.
The audio is automatically muted during special effect modes,
so there is no sound during search.
During the high-speed picture search modes, a short period is
needed to stabilize tape speed when re-entering the PLAY
mode. Slight interference may be observed during this period.
21
OPERATION
Operation with tape
Operation with tape(Continued)
Normal Recording
Timer Recording
Preparation:
This DVD+VCR can be programmed to record up to 8
programs within a period of 1 year. For unattended
recording, the timer needs to know the channels to be
recorded and the starting and ending times.
Turn on the power of both the DVD+VCR and TV.
Tune the TV to the DVD+VCR output channel (CH 3 or 4) or
set the TV’s source selector to VIDEO.
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to
VIDEO.
1
the desired channel by using CH/TRK
2 Select
v/V
V).
(v
Insert a video cassette that the safety tab intact.
3
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2 by pressing INPUT.
Set the desired recording speed (SP or SLP) by
pressing SP/SLP.
This DVD+VCR is not designed to record in LP mode.
Things to know before starting
If you try to set the program timer before setting the clock,
PLEASE SET THE CLOCK appears for a moment and
then CLOCK menu appears on the TV screen. Set the time
and date before proceeding.
Make sure a tape is in the DVD+VCR and the safety tab is
in place or the tape will be automatically ejected.
Preparation:
Turn on the power of both the DVD+VCR and the TV.
Be sure the TV is set to the DVD+VCR output channel (3 or 4).
Make sure the TUNING BAND in the TUNING menu is set
appropriately (TV or CATV).
Press MENU and the MAIN menu will appear.
4
1
z) once.
REC (z
5 Press
Recording will start. (The REC indicator will light in
2 Use v/VV to choose the PROGRAM menu.
the display window.)
SELECT/ENTER to go to the PROGRAM
3 Press
menu.
The PROGRAM menu will appear.
Set the MTS mode as desired (See page 15, 25).
REC indicator appears only when the Output Source is
set to VCR.
6
If a cassette with no safety tab is loaded, the cassette
will be ejected automatically.
x) to stop recording.
Press STOP (x
If the tape reaches the end before STOP (x) is pressed,
the DVD+VCR will automatically stop, rewind, eject, and it
will turn itself off (Only when no disc).
If all programs have already been entered, FULLY
PROGRAMMED message will appear for a moment
and then PROGRAM 1 will appear on the TV screen.
To pause the recording
1 Press PAUSE/STEP (X) to pause the tape during
recording.
The REC indicator will flash in the display window.
2 When you want to continue recording, press
z).
PAUSE/STEP (X) or press REC (z
After 5 minutes in pause mode, the tape will be stopped
automatically to protect the tape and the video heads.
To record one TV program while
watching another
1 Press TV/VCR to select the TV mode during recording.
The TV indicator appears.
2 Using the TV, select the channel to be viewed.
Tips
Always use PAUSE/STEP (X) for the best results when making changes during recording.
For example: To change channels during recording, first press
PAUSE/STEP (X) to put the unit in pause mode. Then select
the desired channel on the DVD+VCR, and press
PAUSE/STEP (X) again to resume recording.
22
4 Use b/BB to choose the PROGRAM No. (1-8).
V to choose the MONTH option.
5 Use
B to choose the desired month.
Use b/B
V to choose the DAY option.
6 Use
B to choose the desired day.
Use b/B
Use V to choose the START option.
7 Use b/BB to choose the desired start time.
V to choose the STOP option.
8 Use
B to choose the desired stop time.
Use b/B
V to choose the CHANNEL option.
9 Use
B to choose the desired channel
Use b/B
(Channel, LINE1 or LINE2).
Cable Users: If you have CABLE TV and used Cable Box
in Connecting Antenna/Cable TV to DVD+VCR (page 11),
using a cable box converter, you must set the channel in
this step to match the cable box output channel (usually
CH 3 or 4). Change channels on the cable box instead of
channels on the DVD+VCR.
Operation with tape(Continued)
11
Use V to choose the SPEED option.
B to choose the desired recording
Use b/B
speed (AUTO, SP or SLP).
AUTO mode determines how long tape is left and
switches speed from SP to SLP, if necessary, to
complete recording the program. There will be some
picture and sound distortion at the point of the speed
change.
Checking (Erasing) the Timer Program
Programming can be checked whenever the DVD+VCR
is turned on.
1 Press MENU and the MAIN menu will appear.
2 Use v/V to choose the PROGRAM menu.
Press SELECT/ENTER and the PROGRAM menu
will appear.
Use V to choose the REPEAT option.
B to choose the desired repeat (ONCE,
Use b/B
WEEKLY or DAILY).
ONCE event....for recording up to 8 programs on a
single day or over the days within a period of 1 year.
WEEKLY event....for recording up to 8 programs on a
certain day of every week.
DAILY event....for recording up to 8 programs at the
same time(s) from Monday through Friday.
3 Use b/B to select a program you want to check or
erase. If you want to erase the program, press
CLEAR.
4 Press MENU to return to the TV screen.
Program Priority
Tip
If the input data is wrong, use v to select the data
B.
and correct it using b/B
12
Press MENU, the program will be memorized
at the DVD+VCR.
indicator lights in the display window.
If the program preset time is past, the PAST TIME
PROGRAMMED message will appear on the TV
screen. Return to the incorrect program and program
it with the correct time.
If you had entered a past date, the timer recording
will be performed on that date of the next year.
Additional programs may be entered by repeating
steps 1-12.
If the starting and ending
times of two or more timer
recordings overlap on the
same day, priority is given to
the earliest recording. For
example, in the diagram at
left Program number 2 will
not be recorded until Program number 1 is finished. The
first part of Program number 2 will not be recorded.
Likewise, Program number 3 will not be recorded until
Program number 2 is finished, and so on.
Cable Users: If your cable hookup is via a TV converter box, you can program multiple recordings only on
the converter box output channel. This is because the
converter determines what channel you view through
your DVD+VCR.
Tip
If you have finished programming and you want to set the
DVD+VCR to record the programs you have entered.
MAKE SURE YOU HAVE INSERTED A TAPE INTO THE
DVD+VCR. The DVD+VCR is now set to record the preset
programs.
Note
If the power fails or the DVD+VCR is unplugged from the AC
outlet, the correct clock time and timer settings are kept in
memory for approximately 3 seconds. After 3 seconds, the
clock and program timer will be reset when power is restored.
Reset the clock according to instructions.
After setting up a timer recording, recording will start if no other
timer recordings are scheduled to occur at the same time (see
“Program Priority” at right).
23
OPERATION
10
Operation with tape (Continued)
Instant Timer Recording
Dubbing and Editing
Instant Timer Recording allows you to make a recording
easily of a preset length without using the program
timer.
If you wish to edit or dub your camcorder (or another
VCR) recordings to this DVD+VCR, the rear (or Front)
panel mounted Audio and Video (A/V) input jacks
make the connections quick and easy. These direct
A/V jacks will also provide better picture results than
using the RF jack on the rear panel.
Preparation:
Turn on the power of both the DVD+VCR and the TV.
Be sure the TV is tuned to the DVD+VCR output channel (3 or 4).
If a direct VIDEO/AUDIO connection is made between the
DVD+VCR and the TV, set the TV’s source selector to VIDEO.
1 Insert a video cassette with the safety tab intact.
the desired channel by using CH/TRK
2 Select
v/V
V) or number (0-9).
(v
The channel number appears on the TV screen.
3
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select the
LINE1 or LINE2.
Set the desired recording speed (SP or SLP) by
pressing SP/SLP.
The tape speed will appear on the TV screen.
4 Press REC (zz) twice.
The menu as illustrated, will appear on the TV screen.
Recording will start. (The
the camcorder’s (or another VCR’s) A/V
1 Connect
outputs to your DVD+VCR as illustrated on page 13.
the input channel “LINE2”. (press INPUT to
2 Set
select LINE2.)
If you have connected your DVD+VCR to the A/V input
jacks on the rear of DVD+VCR, you should select the
input channel LINE1 by pressing INPUT twice.
the tape in the camcorder (or another
3 Play
VCR). If you have a TV attached to your
DVD+VCR, you can see the video playing.
you desire recording to begin, press
4 When
z) once to start.
DVD+VCR’s REC (z
You can stop the recording by pressing STOP (x).
Note
Before recording, please confirm the recording start position.
indicator will light)
z) repeatedly to select the recordREC (z
5 Press
ing time length.
At the end of the recording, the DVD+VCR will stop
recording and shut off.
During Instant Timer Recording, changing the channel
on the DVD+VCR will not be possible.
You can stop the recording by pressing STOP (x).
INSTANT TIMER RECORD MENU
INSTANT TIMER RECORD
0H30M ..... 9H00M ➝ 0H00M
CHANNEL
SPEED
2
SP
START
LENGTH
NOW
0H30M
Length Display
(each additional press of
z) increases recording
REC (z
time 30 minutes)
Checking the Recording Time
Press REC (z) once to check the recording time. The
recalled setting will automatically return to the TV
screen after 6 seconds.
Copying from DVD to VCR
This unit allows you to copy the contents of a DVD to a
VHS tape.
Note
If the DVD you are attempting to copy is copy protected,
you will not be able to copy the disc. It is not permitted
to copy Macrovision encoded DVDs. “Lock” is
displayed in the display window.
1
Insert Disc
Insert the disc you wish to copy in the DVD deck
and close the disc tray.
VHS Tape
2 Insert
Insert a blank VHS video tape into the VCR deck.
H) on the DVD deck.
PLAY (H
3 Press
The DVD will go into play mode
If the DVD disc menu appears, you may need to press
the PLAY (H) manually to begin copying.
To extend the Recording Time
z) on the VCR deck or on the
REC (z
4 Press
remote control.
The recording time can be extended anytime by pressing REC (z).
Subsequent presses result in advancing the recording
time by 30-minute increments.
5 Stop the Copy Process
Notes
If you press PAUSE/STEP (X) during instant timer recording, the DVD+VCR will enter the recording pause mode.
Instant timer recording is cancelled.
If the DVD+VCR is set to “0H00M”, the DVD+VCR goes to
normal recording mode.
24
The DVD+VCR will go into Record mode.
“COPY” indicator will light.
When the DVD is finished playing, press STOP (x) to end
the copy.
You must stop the Copy process manually when the DVD
movie ends, otherwise the unit may record over and over
again.
Note
When you stop the DVD playback during copying, the recording on VCR is stopped automatically.
Operation with tape (Continued)
MTS (Multi-Channel TV Sound)
This DVD+VCR is equipped with the VHS Hi-Fi audio
sound system for recording and playback. The information below gives a brief description of Hi-Fi audio and
how to record and play a tape in the Hi-Fi audio mode.
This DVD+VCR will decode MTS stereo and bilingual
(SAP) off-the-air broadcast sound signals. It also
decodes stereo TV sound from local cable companies,
as long as they operate on assigned cable frequencies
and use the EIA-recommended MTS stereo/bilingual TV
sound system.
Playback with Hi-Fi Stereo Audio Sound
Multichannel TV Sound Indicator (MTS)
A stereo TV with AUDIO/VIDEO input jacks or a stereo
audio system is required for correct stereo playback. To
experience the full and rich stereo sound available with
Hi-Fi recorded tapes, we recommend the connection of
this unit to a home stereo audio system.
Shows On-screen as illustrated below when
SELECT/ENTER is pressed.
1
Set the AUDIO MODE option to HI-FI on the
SETUP menu .
One or both of the indicators will light, depending on the
MTS broadcast.
TV screen
CH 4
STEREO/SAP
STEREO
Lights up when a stereo broadcast
is being received.
SAP
Lights up when a SAP BILINGUAL
broadcast is being received.
If only STEREO appears on the TV screen.
the AUDIO OUTPUT option to STEREO
2 Set
position.
(STEREO) POSITION: The left channel sound (L) is
heard from the left speaker and the right channel sound
(R) is heard from the right speaker.
(LEFT) POSITION: The left channel sound (L) is heard
from both speakers.
(RIGHT) POSITION: The right channel sound (R) is heard
from both speakers.
3 Press MENU.
H).
Insert a cassette and press PLAY (H
4 Adjust
volume at your stereo system.
The DVD+VCR can record in stereo onto the VHS Hi-Fi audio
tracks when the BROADCAST TYPE option is in the STEREO
position. The DVD+VCR will also record mono audio onto the
mono audio track.
If only SAP appears on the TV screen.
Set the BROADCAST TYPE option to SAP.
If STEREO/SAP appears on the TV screen
Use the BROADCAST TYPE option to select the desired
recording mode (STEREO or SAP).
SAP (Second Audio Program) Recording
Some stations transmit a Second Audio Program, which
is used for a second language or additional information.
When the station broadcasts a Second Audio Program,
follow the procedure below to record the SAP.
Insert a video cassette with the safety tab intact.
1
the BROADCAST TYPE option to SAP
2 Set
(SETUP menu).
Do this only if the SAP appears on the TV screen or you
know the program will use the SAP.
3 Press MENU.
the desired recording speed (SP or SLP) by
4 Set
pressing SP/SLP.
the desired channel. The SAP should
5 Select
appear on the TV screen.
6 Press REC (zz) once
7 Press STOP (xx) to stop recording.
You are now recording the program you see and hear on the
TV.
25
OPERATION
VHS Hi-Fi Stereo System/
MTS Broadcast
Operation with tape (Continued)
Tape Counter Memory Feature
Real-Time Counter
Shows length of tape run in hours, minutes, and seconds. Press CLK/CNT to select the real-time counter
display.
Every press of CLK/CNT changes the TV screen as
illustrated below.
2:15 AM
CLOCK
0:05:25
COUNTER
REM 1:07
REMAINING TIME
Counter changes to “0:00:00” when the cassette is
ejected.
The real-time counter does not operate if nothing is recorded on the tape.
The real-time counter will not work unless a tape is
inserted.
Additional Information
In manual recording, Timer recording, Instant Timer
Recording, playback, or fast forward modes, the DVD+VCR
automatically starts rewinding the tape at the end of the
tape. The cassette will stop at the beginning of the tape and
be ejected, and the DVD+VCR will turn itself off (Only when
no disc).
After you have finished using the DVD+VCR, rewind, eject,
and remove the cassette. Place the cassette in its protective sleeve to protect it from dust. It is not necessary to
rewind the cassette before removing it, but if you do, it will
be ready to play or record the next time you use it.
Be sure the DVD+VCR Channel Selector is on the correct
channel you wish to record. The channel that is being
recorded can always be checked by setting the television
on the DVD+VCR channel (3 or 4) and pressing the
TV/VCR selector to turn off the DVD+VCR’s TV indicator.
Do not attempt to hook up more than one television set to
the DVD+VCR for either recording or playback.
Counter Memory Function
Auto Play System
This is useful if there is a section of tape you want to
view immediately after recording or if you want to return
to the same point several times.
This DVD+VCR features automatic playback.
Load a cassette (with the safety tab removed).
1
CLK/CNT repeatedly to display the real2 Press
time counter appears on the TV screen.
the point that you want locate later, reset the
3 Atreal-time
counter to “0:00:00” by pressing
CLEAR.
Begin recording or playing a tape.
4
x) when recording or playback finPress STOP (x
5 ishes.
.).
BACKWARD (.
6 Press
The tape automatically stops when the tape counter
returns to about “0:00:00”.
Continue to play or record.
Tape Remaining
This function allows the time of the remaining tape to be
displayed during recording or playback.
Press CLK/CNT until the REM indicator displays on the
TV screen during recording or playback.
Note
The remaining tape length indicator may not be displayed
correctly depending on the condition of the tape and the kind of
the tape (T-140, T-160, or T-210 etc)
26
The Output Source is changed to VCR mode automatically.
The power turns on automatically and playback begins.
At the end of the tape, the DVD+VCR stops, then rewinds.
The cassette is ejected after rewinding and turn itself off
automatically.
LOAD
AUTO
AUTO
PLAY
TAPE
AUTO
REWIND
EJECT
AUTO
POWER
OFF
Note
Auto power off does not function during regular DVD play
mode. (DVD+VCR power stays on.)
Operation with DVD
Playback Setup
General Features
DVD
Turn on the TV and select the video input source connected to the DVD+VCR.
Audio system: Turn on the audio system and select
the input source connected to the DVD+VCR.
Set the Output Source to DVD as shown in “Setting
the Output Source” on page 6.
1 Press OPEN/CLOSE (ZZ) to open the disc tray.
your chosen disc in the tray, with the play2 Load
back side down.
Z) to close the tray.
Press OPEN/CLOSE (Z
3 Playback
starts automatically. If playback does not
start, press PLAY (H).
In some cases, the disc menu might appear
instead.
If a menu screen is displayed
The menu screen may be displayed first after loading a
DVD which offers a menu.
DVD
Use the b/B/v/V buttons to select the title/chapter you
want to view, then press SELECT/ENTER to start
playback.
Press TITLE or DISK MENU to return to the menu
screen.
stop playback at any other time, press STOP.
4 ToThis
is RESUME STOP mode.
To exit RESUME STOP mode, press STOP again.
Notes
If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit password
must be entered and/or the disc must be authorized
(see “LOCK”, on page 20).
DVDs may have a region code.
Your DVD+VCR will not play discs that have a region
code different from your DVD+VCR. The region code
for this DVD+VCR is 1 (one).
Do not keep an image or on-screen displayed for a
long time.
Note
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
Moving to another TITLE
DVD
1/3
When a disc has more than one title, you can move to
another title as follows:
Press DISPLAY then press v/V to select the title
icon. Then press the appropriate numbered button
(0-9) to select a title number.
To go directly to any title at STOP mode
(or RESUME STOP mode), press the numbered
button (0-9).
Moving to another CHAPTER
DVD
1 / 12
When a title on a disc has more than one chapter, you
can move to another chapter as follows:
Press BACKWARD (.) or FORWARD (>) briefly
during playback to return to the beginning of the current chapter or to select the next chapter.
Press BACKWARD (.) twice briefly to step back to
the previous chapter.
To go directly to any chapter during playback,
V to select chapter
press DISPLAY. Then, press v/V
icon. Then, enter the chapter number using the
numbered buttons (0-9).
Slow Motion
DVD
1 Press PAUSE/STEP (X) during playback.
The DVD+VCR will now go into PAUSE mode.
2 Press BACKWARD (.) or FORWARD (>)
during pause mode.
The DVD+VCR will enter SLOW mode.
3 Use BACKWARD (.) or FORWARD (>) to
select the required speed: t 1/16, t 1/8, t 1/4 or
t 1/2 (backward), or T 1/16, T 1/8, T 1/4 or T
1/2 (forward).
4 To return to playback, press PLAY (H).
27
OPERATION
Playing DVD
Operation with DVD (Continued)
General Features (Continued)
Time Search
Still Picture and Frame-by-Frame Playback
The Time Search function allows you to start playing at
any chosen time on the disc.
DVD
1 Press PAUSE/STEP (X) during playback.
The DVD+VCR will now go into PAUSE mode.
2 You can advance the picture frame by frame by
pressing PAUSE/STEP (X) repeatedly on the remote
control.
3 To return to playback, press PLAY (H).
Search
DVD
1 Press and hold BACKWARD (.) or FORWARD (>)
for about two seconds during playback.
The DVD+VCR will now go into SEARCH mode.
2 Press and hold BACKWARD (.) or FORWARD (>)
repeatedly to select the required speed: mX2, mX4,
mX16, mX100 (backward) or MX2, MX4,
MX16, MX100 (forward).
3 To return to playback, press PLAY (H).
Repeat
DVD
Title
DVD Video Discs - Repeat Chapter/Title/Off
1 To repeat the currently playing chapter, press
REPEAT.
The Repeat Chapter icon appears on the TV screen.
2 To repeat the title currently playing, press REPEAT a
second time.
The Repeat Title icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
Repeat A-B
DVD
A-B
To repeat a sequence:
1 Press A-B at your chosen starting point.
“A-” appears briefly on the TV screen.
2 Press A-B again at your chosen end point (after more
than 3 seconds).
“A-B” appears briefly on the TV screen, and the repeat
sequence begins.
3 To cancel the sequence, press A-B.
28
DVD
0:20:09
1 Press DISPLAY during playback. The on-screen
display appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
V to select the Time
2 Within 10 seconds, use v/V
Search icon in the on-screen display.
The “-:--:--” appears in the Time Search box.
3 Within 10 seconds, use the numbered buttons to
enter the required start time. Enter hours, minutes
and seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
4 Within 10 seconds, press SELECT/ENTER.
Playback starts from the selected time on the disc. If you enter
an invalid time, playback will continue from the current point.
3D Surround
DVD
3D SUR
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1 Press DISPLAY during playback.
2 Use v/V to select the sound icon.
The sound option will be highlighted.
3 Use b/B to to select “3D SUR”.
To turn off the 3D Surround effect, select “Normal”.
Operation with DVD (Continued)
Zoom
DVD
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
1 Press ZOOM during playback or still playback to activate the Zoom function.
The square frame will be displayed in the right bottom of the
picture. If no button is pressed for more than 10 seconds,
the square frame will disappear.
Each press of the ZOOM button changes the TV screen in
the sequence shown below.
400% size → 1600% size → multi zoom mode → normal size
2 Use the b B v V buttons to move through the
zoomed picture (400% or 1600%), or to enlarge and
reduce the picture size through the multi zoom mode.
3 To resume normal playback, press ZOOM repeatedly
until the normal picture appears.
Note
The zoom function may not work for some DVDs.
The zoom function may not work on multi-angle
scenes.
Marker Search
DVD
Special DVD Features
Checking the contents of DVD Video
discs: Menus
DVDs may contain menus that allow you to access special features. To use the disc menu, press DISC MENU.
Then, press the appropriate number button to select an
option. Or, use b/B/v/V buttons to highlight your selection, then press SELECT/ENTER.
Title Menu
DVD
1 Press TITLE.
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
3 To remove the title menu, press DISC MENU.
Disc Menu
DVD
1 Press DISC MENU.
The disc menu is displayed.
2 To remove the disc menu, press DISC MENU again.
#1
1/9
1 2 3 4 5 6 7 8 9
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1 During disc playback, press MARKER when playback
reaches the spot that you want to memorize.
The Marker icon will appear on the TV screen briefly.
Camera Angle
The number of the current angle appears on the TV screen.
Changing the Audio Language
The Marker Search menu will appear on the screen.
3 Press SELECT/ENTER.
Playback will start from the Marked scene.
4 To remove the MARKER SEARCH menu, press
SEARCH.
DVD
1 ENG
D
5.1 CH
1 During disc playback, press SEARCH.
2 Within 10 seconds, press 1/2 to select a Marker number that you want to recall.
1/1
If the disc contains scenes recorded at different camera
angles, you can change to a different camera angle
during playback.
Press ANGLE repeatedly during playback to select a
desired angle.
2 Repeat step 1 to enter up to nine Marker points on a
disc.
To Recall a Marked Scene
DVD
Press AUDIO repeatedly during playback to hear a
different audio language or audio track.
Subtitle
DVD
ABC
1 ENG
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
To clear a Marked Scene
1 During disc playback, press SEARCH.
The Marker Search menu will appear on the screen.
If
Note
appears, the feature is not available on the disc.
2 Within 10 seconds, press 1/2 to select a Marker number that you want to erase.
3 Press CLEAR.
The Marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
29
OPERATION
General Features (Continued)
Operation with Audio CD and MP3 Discs
Playing an Audio CD and MP3
Notes on MP3 Recordings
Discs
About MP3
CD
MP3
An MP3 file is audio data compressed by using the
MPEG1 audio layer-3 file-coding scheme. We call
files that have the “.mp3” file extension “MP3 files”.
The player can not read an MP3 file that has a file
extension other than “.mp3”.
The DVD+VCR can play an audio CD. Also, the
DVD+VCR can play MP3 formatted recordings on
CD-ROM, CD-R or CD-RW discs.
Before playing MP3 recordings, read the notes on MP3
Recordings on the right side of this page.
1
Insert a disc and close the tray.
Audio CD; Audio CD menu appears on the TV
screen. Go to step 3.
MP3 disc; The MP3 menu appears on the TV
screen. Go to step 2
00:00:00
00:00:00
1 / 12
Audio CD
1.
2.
3.
4.
1 / 104
MP3
Program
List
Program
List
TRACK1
Add
Music Folder 1
Add
TRACK2
Add All
Music Folder 2
Add All
TRACK3
Delete
Music Folder 3
Delete
TRACK4
Delete All
Music Folder 4
Delete All
TRACK5
Music Folder 5
TRACK6
Music Folder 6
TRACK7
Music Folder 7
TRACK8
Music Folder 8
Audio CD Menu
2
MP3 Disc compatibility with this player is limited as follows:
5.
MP3 Menu
6.
Press v/V to select a folder then press
SELECT/ENTER.
A list of files in the folder appears.
Press v/V to select a track then press
3 PLAY
H) or SELECT/ENTER.
(H
Playback starts.
During playback, the current track’s elapsed playing
time will appear on the display window and menu.
Playback will stop at the end of the disc.
Tips
Press and hold V to move to the next page.
Press and hold v to move to the previous page.
If you are in a file list on the MP3 menu and want to
return to the Folder list, use the v/V to highlight
and
press SELECT/ENTER.
playback at any other time,
4 TopressstopSTOP
x).
(x
30
7.
8.
Sampling Frequency / only at 44.1 kHz
Bit rate / within 32 - 320kbps
CD-R physical format should be “ISO 9660”
If you record MP3 files using the software which
cannot create a FILE SYSTEM, for example “DirectCD” etc., it is impossible to playback MP3 files. We
recommend that you use “Easy-CD Creator”, which
creates an ISO9660 file system.
A single session disc requires MP3 files in the first
track. If there is no MP3 file in the 1st track, it cannot play back MP3 files. If you wish to playback MP3
files, format all the data in the disc or use a new
one.
File names should be named using 8 letters or less
and must incorporate “.mp3” extension
e.g. “********.MP3”.
Do not use special letters such as “/ : * ? “ < > ” etc.
Total number of files and folders on the disc should
be less than 999.
This DVD+VCR requires discs/recordings to meet
certain technical standards in order to achieve optimal
playback quality. Pre-recorded DVDs are automatically
set to these standards. There are many different types
of recordable disc formats (including CD-R containing
MP3 files). That require certain pre-existing conditions
(see above) to insure compatible playback.
Customers should also note that permission must
be required in order to download MP3 files and
music from the Internet. Our company has no right
to grant such permission. Permission should
always be sought from the copyright owner.
Operation with Audio CD and MP3 Discs (Continued)
CD
Random
MP3
1 Press PAUSE/STEP (X) during playback.
2 To return to playback, press PLAY(H) or press
PAUSE/STEP (X) again.
MP3
Press BACKWARD (.) or FORWARD (>) briefly
during playback to go to the next track or to return to
the beginning of the current track.
Press BACKWARD (.) twice briefly to step back to
the previous track.
To go directly to any track, enter the track number
using the numbered buttons (0-9) during playback.
Repeat Track/All/Off
CD
MP3
1 Press RANDOM during playback.
The unit automatically begins Random Playback and
“Random” appears on the menu screen.
2 To return to normal playback, press RANDOM
repeatedly until “Random” disappears on the menu
screen.
Moving to another Track
CD
CD
MP3
1 To repeat the track currently playing, press REPEAT.
Repeat A-B
CD
To repeat a sequence in a title:
1 Press A-B at your chosen starting point.
The Repeat icon and “A” appears on the menu screen.
2 Press A-B again at your chosen end point.(after more
then 3 seconds)
The Repeat icon and “A - B” appears on the menu screen,
and the repeat sequence begins.
3 To exit the sequence and return to normal play, press
A-B again.
The Repeat icon and “TRACK” appears on the menu screen.
2 To repeat all tracks on a disc, press REPEAT a second time.
The Repeat icon and “ALL” appears on the menu screen.
3 To cancel Repeat mode, press REPEAT a third time.
Search
CD
MP3
1 Press and hold BACKWARD (.) or FORWARD
(>) for about two seconds during playback.
The player will now go into SEARCH mode.
2 Press and hold BACKWARD (.) or FORWARD
(>) repeatedly to select the required speed: mX2,
mX4, mX8 (backward) or MX2, MX4, MX8
(forward).
Search speed and direction are indicated on the menu
screen.
3 To exit SEARCH mode, press PLAY(H).
Note
The DVD+VCR mutes sound during search mode of
MP3 files.
31
OPERATION
Pause
Programmed Playback
CD
MP3
Programmed Playback with Audio CD
and MP3 Discs
The Program function enables you to store your favorite
tracks from any disc in the player memory.
Program can contain 99 tracks (Audio CD) or 300
tracks (MP3).
1
2 Press v V b B to select a track on the List.
PROGRAM. Or, press v V b B to highlight
3 Press
the “Add” icon then press SELECT/ENTER.
Insert an Audio CD or MP3 disc.
Audio CD or MP3 menu will appear.
The selected track is added to the program list.
steps 2-3 to place additional tracks on
4 Repeat
the Program list.
5 Press v V b B to move to the Program list.
v/V to select the track you want to start
6 Press
playing.
00:00:00
00:00:00
1 / 12
1 / 104
MP3
Audio CD
Program
List
Program
List
TRACK1
Add
TRACK8
Add
Music8
TRACK2
Add All
TRACK3
Music1
Add All
Music16
TRACK3
Delete
TRACK12
Music2
Delete
Music5
TRACK4
Delete All
Delete All
Music9
TRACK7
Music3
TRACK5
TRACK6
Music4
Music1
TRACK6
TRACK9
Music5
Music7
TRACK7
TRACK1
Music6
Music6
TRACK8
TRACK10
Music7
Music3
Tips
Press and hold V to move to the next page.
Press and hold v to move to the previous page.
If you are in a file list on the MP3 menu and want to
return to the Folder list, use the v/V to highlight
and
press SELECT/ENTER.
7
H) or SELECT/ENTER to start.
Press PLAY (H
Playback begins in the order in which you programmed
the tracks.
Playback stops after all of the tracks on the Program list
have played once.
resume normal playback from pro8 To
grammed playback, select a track on the
List then press SELECT/ENTER.
32
Repeat Programmed Tracks
To repeat the track currently playing, press REPEAT.
The Repeat icon and “TRACK” appears on the screen.
To repeat all tracks on the program list, press
REPEAT a second time.
The Repeat icon and “ALL” appears on the screen.
To cancel Repeat mode, press REPEAT a third time.
Erasing a Track from Program List
1 Select the track that you wish to erase from the
Program list.
2 Press v V b B to highlight the “Delete” icon then
press SELECT/ENTER. Or, press CLEAR.
The selected track is deleted on the program list.
3 Repeat steps 1-2 to delete additional tracks on the
Program list.
Erasing the Complete Program List
Press v V b B to highlight the “Delete All” icon then
press SELECT/ENTER.
All tracks on the program list are deleted.
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Cause
Correction
No power.
The power cord is disconnected.
Plug the power cord into the wall outlet
securely.
The power is on, but
the DVD+VCR does not
work.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
No picture.
The TV is not set to receive DVD+VCR
signal output.
Select the appropriate video input mode
on the TV so the picture from the
DVD+VCR appears on the TV screen.
TV/VCR mode for DVD+VCR is set to
TV.
Press the TV/VCR button on the remote
control repeatedly to choose VCR
mode. TV indicator disappears in the
display window.
The video cable is not connected
securely.
Connect the video cable securely.
The connected TV power is turned off.
Turn on the TV.
The equipment connected with the
audio cable is not set to receive
DVD+VCR signal output.
Select the correct input mode of the
audio receiver so you can listen to the
sound from the DVD+VCR.
The audio cables are not connected
securely.
Connect the audio cable securely.
The power of the equipment connected
with the audio cable is turned off.
Turn on the equipment connected with
the audio cable.
The Digital Audio Output is set to the
wrong position.
Set the Digital Audio Output to the
correct position, then turn on the
DVD+VCR again by pressing POWER.
The disc is dirty.
Clean the disc.
Tape heads are dirty.
Clean video heads.
Tape is a rental or was recorded on
another VCR.
Use CH/TRK (v/V) for manual tracking
adjustment while tape is playing.
No disc is inserted.
No tape is inserted.
Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
An unplayable disc is inserted.
Insert a playable disc. (Check the disc
type, color system, and Regional code.)
The disc is placed upside down.
Place the disc with the playback side down.
The disc is not placed within the guide.
Place the disc on the disc tray correctly
inside the guide.
The disc is dirty.
Clean the disc.
The Rating level is set.
Cancel the Rating function or change
the rating level.
The remote control is not pointed at the
remote sensor of the DVD+VCR.
Point the remote control at the remote
sensor of the DVD+VCR.
The remote control is too far from the
DVD+VCR.
Operate the remote control within 23 ft
(7 m).
There is an obstacle in the path of the
remote control and the DVD+VCR.
Remove the obstacle.
The batteries in the remote control are
exhausted.
Replace the batteries with new ones.
This remote control use the same
buttons for VCR and DVD functions
(ex. PLAY).
When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
No sound.
The playback picture is
poor.
The DVD+VCR does
not start playback.
The remote control
does not work properly.
33
REFERENCE
Symptom
Troubleshooting (Continued)
Cause
Symptom
Correction
Some channels are
skipped over when
using CH/TRK (v/V)
Those channels were deleted with the
CH. ADD/DEL option.
Use CH. ADD/DEL. to restore channels.
See “Channel Selection” on page 15.
Picture and sound of
broadcasting channel
are weak or missing.
Antenna or cables are loose.
Tighten connections or replace cable.
Wrong TUNING BAND option is being
used.
Try all TUNING BAND options. See
“Channel Selection” on page 15 for
details.
Camcorder image is not
shown.
Camcorder is off.
Turn camcorder on and operate
properly.
Camcorder image via
A/V input to DVD+VCR
is not shown on TV
screen.
DVD+VCR SOURCE SELECT is not set
to LINE1 or LINE2.
Press INPUT to select LINE input channel (LINE1 or LINE2).
Timer recording is not
possible.
Clock in DVD+VCR is not set to correct
time.
Set clock to correct time. See “Setting
the Clock” on page 16.
Timer has been programmed
incorrectly.
Reprogram Timer. See “Timer
Recording” on pages 22 and 23.
indicator does not appear after programming timer.
Reprogram Timer.
DVD+VCR is in Timer Recording mode.
This is the normal indication that the
DVD+VCR is in TIMER mode.
TV is not Stereo-compatible.
No action is possible.
Broadcast program is not in stereo format.
No action is possible.
DVD+VCR A/V Out jacks are not connected to TV A/V In jacks.
Make A/V connections. Stereo is
available only via A/V output from
DVD+VCR.
DVD+VCR Audio/Video Out is not
selected for viewing at the TV.
Select AUX or A/V source as TV input.
DVD+VCR BROADCAST TYPE mode is
set to SAP or MONO.
Set BROADCAST TYPE mode to
STEREO. See “Setting the VCR Setup
Menu” on page 15.
indicator appears
after DVD+VCR is turned
off.
Stereo Audio Record
and/or Playback is not
present.
Moisture Condensation
Moisture condensation can occur:
In locations where moisture condensation may occur:
• When the DVD+VCR is moved from a cold place to a
warm place.
• Keep the DVD+VCR plugged into an AC power outlet
with POWER On. This will help prevent condensation.
• Under extremely humid conditions.
• When condensation has occurred, wait a few hours
for the DVD+VCR to dry before using it.
34
Language Code List
Language
Code
Language
Code
Language
Code
Language
Code
Abkhazian
6566
Fiji
7074
Lingala
7678
Singhalese
8373
Afar
6565
Finnish
7073
Lithuanian
7684
Slovak
8375
Afrikaans
6570
French
7082
Macedonian
7775
Slovenian
8376
Albanian
8381
Frisian
7089
Malagasy
7771
Somali
8379
Amharic
6577
Galician
7176
Malay
7783
Spanish
6983
Arabic
6582
Georgian
7565
Malayalam
7776
Sudanese
8385
Armenian
7289
German
6869
Maltese
7784
Swahili
8387
Assamese
6583
Greek
6976
Maori
7773
Swedish
8386
Aymara
6588
Greenlandic
7576
Marathi
7782
Tagalog
8476
Azerbaijani
6590
Guarani
7178
Moldavian
7779
Tajik
8471
Bashkir
6665
Gujarati
7185
Mongolian
7778
Tamil
8465
Basque
6985
Hausa
7265
Nauru
7865
Tatar
8484
Bengali; Bangla
6678
Hebrew
7387
Nepali
7869
Telugu
8469
Bhutani
6890
Hindi
7273
Norwegian
7879
Thai
8472
Bihari
6672
Hungarian
7285
Oriya
7982
Tibetan
6679
Breton
6682
Icelandic
7383
Panjabi
8065
Tigrinya
8473
Bulgarian
6671
Indonesian
7378
Pashto, Pushto
8083
Tonga
8479
Burmese
7789
Interlingua
7365
Persian
7065
Turkish
8482
Byelorussian
6669
Irish
7165
Polish
8076
Turkmen
8475
Cambodian
7577
Italian
7384
Portuguese
8084
Twi
8487
Catalan
6765
Japanese
7465
Quechua
8185
Ukrainian
8575
Chinese
9072
Javanese
7487
Rhaeto-Romance 8277
Urdu
8582
Corsican
6779
Kannada
7578
Romanian
8279
Uzbek
8590
Croatian
7282
Kashmiri
7583
Russian
8285
Vietnamese
8673
Czech
6783
Kazakh
7575
Samoan
8377
Volapük
8679
Danish
6865
Kirghiz
7589
Sanskrit
8365
Welsh
6789
Dutch
7876
Korean
7579
Scots Gaelic
7168
Wolof
8779
English
6978
Kurdish
7585
Serbian
8382
Xhosa
8872
Esperanto
6979
Laothian
7679
Serbo-Croatian
8372
Yiddish
7473
Estonian
6984
Latin
7665
Shona
8378
Yoruba
8979
Faeroese
7079
Latvian, Lettish
7686
Sindhi
8368
Zulu
9085
35
REFERENCE
Enter the appropriate code number for the initial settings “Disc Audio”, “Disc Subtitle” and/or “Disc Menu”
(See page 18).
Country Code List
Enter the appropriate code number for the initial setting “Country Code” (See page 20).
Country
Afghanistan
Albania
Algeria
American Samoa
Andorra
Angola
Anguilla
Antarctica
Antigua and Barbuda
Argentina
Armenia
Aruba
Australia
Austria
Azerbaidjan
Bahamas
Bahrain
Bangladesh
Barbados
Belarus
Belgium
Belize
Benin
Bermuda
Bhutan
Bolivia
Bosnia-Herzegovina
Botswana
Bouvet Island
Brazil
British Indian
Ocean Territory
Brunei Darussalam
Bulgaria
Burkina Faso
Burundi
Cambodia
Cameroon
Canada
Cape Verde
Cayman Islands
Central African Republic
Chad
Chile
China
Christmas Island
Cocos (Keeling) Islands
Colombia
Comoros
Congo
Cook Islands
Costa Rica
Croatia
Cuba
Cyprus
Czech Republic
Denmark
Djibouti
Dominica
Dominican Republic
East Timor
Ecuador
Egypt
36
Code
AF
AL
DZ
AS
AD
AO
AI
AQ
AG
AR
AM
AW
AU
AT
AZ
BS
BH
BD
BB
BY
BE
BZ
BJ
BM
BT
BO
BA
BW
BV
BR
IO
BN
BG
BF
BI
KH
CM
CA
CV
KY
CF
TD
CL
CN
CX
CC
CO
KM
CG
CK
CR
HR
CU
CY
CZ
DK
DJ
DM
DO
TP
EC
EG
Country
Code
El Salvador
SV
Equatorial Guinea
GQ
Eritrea
ER
Estonia
EE
Ethiopia
ET
Falkland Islands
FK
Faroe Islands
FO
Fiji
FJ
Finland
FI
Former Czechoslovakia
CS
Former USSR
SU
France
FR
France (European Territory) FX
French Guyana
GF
French Southern Territories TF
Gabon
GA
Gambia
GM
Georgia
GE
Germany
DE
Ghana
GH
Gibraltar
GI
Great Britain
GB
Greece
GR
Greenland
GL
Grenada
GD
Guadeloupe (French)
GP
Guam (USA)
GU
Guatemala
GT
Guinea
GN
Guinea Bissau
GW
Guyana
GY
Haiti
HT
Heard and
McDonald Islands HM
Honduras
HN
Hong Kong
HK
Hungary
HU
Iceland
IS
India
IN
Indonesia
ID
Iran
IR
Iraq
IQ
Ireland
IE
Israel
IL
Italy
IT
Ivory Coast
CI
Jamaica
JM
Japan
JP
Jordan
JO
Kazakhstan
KZ
Kenya
KE
Kiribati
KI
Kuwait
KW
Kyrgyzstan
KG
Laos
LA
Latvia
LV
Lebanon
LB
Lesotho
LS
Liberia
LR
Libya
LY
Liechtenstein
LI
Lithuania
LT
Luxembourg
LU
Country
Macau
Macedonia
Madagascar
Malawi
Malaysia
Maldives
Mali
Malta
Marshall Islands
Martinique (French)
Mauritania
Mauritius
Mayotte
Mexico
Micronesia
Moldavia
Monaco
Mongolia
Montserrat
Morocco
Mozambique
Myanmar
Namibia
Nauru
Nepal
Netherlands
Netherlands Antilles
New Caledonia (French)
New Zealand
Nicaragua
Niger
Nigeria
Niue
Norfolk Island
North Korea
Northern Mariana Islands
Norway
Oman
Pakistan
Palau
Panama
Papua New Guinea
Paraguay
Peru
Philippines
Pitcairn Island
Poland
Polynesia (French)
Portugal
Puerto Rico
Qatar
Reunion (French)
Romania
Russian Federation
Rwanda
S. Georgia
& S. Sandwich Isls.
Saint Helena
Saint Kitts
& Nevis Anguilla
Saint Lucia
Saint Pierre and Miquelon
Saint Tome and Principe
Code
MO
MK
MG
MW
MY
MV
ML
MT
MH
MQ
MR
MU
YT
MX
FM
MD
MC
MN
MS
MA
MZ
MM
NA
NR
NP
NL
AN
NC
NZ
NI
NE
NG
NU
NF
KP
MP
NO
OM
PK
PW
PA
PG
PY
PE
PH
PN
PL
PF
PT
PR
QA
RE
RO
RU
RW
GS
SH
KN
LC
PM
ST
Country
Saint Vincent
& Grenadines
SamoaWS
San Marino
Saudi Arabia
Senegal
Seychelles
Sierra Leone
Singapore
Slovak Republic
Slovenia
Solomon Islands
Somalia
South Africa
South Korea
Spain
Sri Lanka
Sudan
Suriname
Svalbard and
Jan Mayen Islands
Swaziland
Sweden
Switzerland
Syria
Tadjikistan
Taiwan
Tanzania
Thailand
Togo
Tokelau
Tonga
Trinidad and Tobago
Tunisia
Turkey
Turkmenistan
Turks and Caicos Islands
Tuvalu
Uganda
Ukraine
United Arab Emirates
United Kingdom
United States
Uruguay
USA Minor Outlying Islands
Uzbekistan
Vanuatu
Vatican City State
Venezuela
Vietnam
Virgin Islands (British)
Virgin Islands (USA)
Wallis and Futuna Islands
Western Sahara
Yemen
Yugoslavia
Zaire
Zambia
Zimbabwe
Code
VC
SM
SA
SN
SC
SL
SG
SK
SI
SB
SO
ZA
KR
ES
LK
SD
SR
SJ
SZ
SE
CH
SY
TJ
TW
TZ
TH
TG
TK
TO
TT
TN
TR
TM
TC
TV
UG
UA
AE
UK
US
UY
UM
UZ
VU
VA
VE
VN
VG
VI
WF
EH
YE
YU
ZR
ZM
ZW
Specifications
General
AC 120V , 60 Hz
23W
430 X 97.5 X 293 mm (16.9 x 3.9 x 11.5 inches) (w x h x d)
4.8 kg (10.58 lbs)
5˚C to 40˚C (41˚F to 104˚F)
5 % to 90 %
NTSC
REFERENCE
Power requirements
Power consumption
Dimensions (approx.)
Mass (approx.)
Operating temperature
Operating humidity
Signal system
Inputs
ANTENNA IN
VHS VIDEO IN
VHS AUDIO IN
Antenna or CATV input, 75 ohms
1 Vp-p 75 ohms, sync negative, RCA jack x 2
-6.0 dBm more than 47 kohms, RCA jack (L, R) x 2
VIDEO OUT
S-VIDEO OUT
1 Vp-p 75 ohms, sync negative
(Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.3 V (p-p) 75 ohms
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
0.5 V (p-p), 75 ohms, RCA jack x 1
2.0 Vrms (1 KHz, 0 dB), 600 ohms, RCA jack (L, R) x 1
Channel 3 or 4
Outputs
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Audio output (digital audio)
Audio output (analog audio)
RF OUT
VCR Specifications
Head system
Timer
Tape speed
Tape width
Maximum recording time
Rewind time
Antenna
VHF output signal
Channel coverage
Frequency range
Signal-to-noise ratio
Dynamic range
Channel separation
Four head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)
About 3 minutes (T-120)
75 ohms (VHF/UHF)
Channel 3 or 4 (Switchable)
VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)
20Hz to 20kHz
More than 43dB
More than 88 dB
More than 60 dB
DVD Specifications
Laser system
Frequency response
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Semiconductor laser, wavelength 650 nm
DVD (PCM 96 kHz): 8 Hz to 44 kHz, DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
More than 100dB (ANALOG OUT jacks only)
Less than 0.008%
More than 95 dB (CD), More than 100 dB (DVD)
Accessory:
Video cable x 1, Audio cable(L/R) x 1, RF 75-ohm Coaxial Cable x 1, Remote control x 1, Batteries x 2
Design and specifications are subject to change without notice.
37
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement