Scotsman Ice | C1448 | User's Manual | Scotsman Ice C1448 User's Manual

Scotsman Ice C1448 User's Manual
Installation and
User's Manual
Models C1448, C1848, C2148W
C1448, C1848, C2148W
Air and Water Cooled User Manual
Introduction
The design of this modular cuber is the result of
years of experience and testing. Standard features
include front accessible indicator lights and on-off
switches that provide the user with fast access to
critical information and easy operational control.
When desired, optional controls can add features
like ultrasonic bin ice level sensing, seven day
programmable bin ice level setting, remote lock out
and more.
This installation and user manual is divided into
three main sections: Installation, which provides
the trade person with the information needed to set
up and install this product; Use and Operation,
which provides the user with the information to use
the product; and Maintenance, which provides the
user with the information needed keep it operating
efficiently.
Table of Contents
Installation: Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2
Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
Product Description & Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4
Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 7
Panel Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8
Uncrate and Set Up
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 9
Plumbing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 10
Drains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 11
Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12
Final Check List
Initial Start Up
Adjustments
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 15
Water flush setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 16
Use and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 17
Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 18
Options and Other Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 19
Cleaning, Sanitation and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 20
Air cooled condenser filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 22
What to do before calling for service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 23
Note any Caution or Warning symbols when they
appear on the product or in this manual. They
indicate potential hazards.
November 2006
Page 1
C1448, C1848, C2148W
Air and Water Cooled User Manual
Installation: Product Specifications
Location Limitations: The product is designed to be Environmental Limitations
installed indoors, in a controlled environment. Air
cooled models discharge very warm air into the
Minimum
room out the back. Space must be allowed at the
Air temperature 50oF.
left side and back for air intake and discharge.
Water cooled models discharge warm water into
Water
40oF.
the building’s drain. Space needs to be provided on temperature
both sides and above for service access.
Water pressure
20 psi
Maximum
100oF.
100oF.
80 psi
Space Limitations
Power supply – acceptable voltage ranges
Note: Although the machine will function, ice
capacity of air cooled machines will be significantly
reduced with minimal clearance at the sides, back
and top. Some space is recommended for service
and maintenance purposes on all models.
6" of space at the sides and back are required for
adequate operation. To get the most capacity,
locate the machine away from heat producing
appliances and heating ducts. Provide several feet
of space to the left for maximum ice capacity.
Walls or other large machines near to the ice
machine might also cause a reduction in ice
capacity. One foot behind and two feet above will
be required to make rated capacity.
208-230 volt
model
Minimum
Maximum
198 volts
253 volts
Warranty Information
The warranty statement for this product is provided
separately from this manual. Refer to it for
applicable coverage. In general warranty covers
defects in material or workmanship. It does not
cover maintenance, corrections to installations, or
situations when the machine is operated in
circumstances that exceed the limitations printed
above.
Airflow is in the front, in the left side, out the back
(as viewed from the front).
Airflow Direction
November 2006
Page 2
C1448, C1848, C2148W
Air and Water Cooled User Manual
Product Information
The product is a modular cuber. That type of
Options:
machine is designed to be placed on an ice storage
bin or an ice dispenser. Many installations only
There are several field-installed options that can be
require the matching bin, but some also require an installed at initial start up or later. They include:
adapter to be placed between the bin and the
cuber or between the dispenser and the cuber.
• Vari-Smartä adjustable ice level system.
This product cannot be stacked. See the chart
• SmartBoardä advanced feature control.
for application information.
Some installations require bin adapters. See the
Model Number Description
table below.
Example:
•
•
•
•
•
Standard Bin Applications - Adapter
information.
C1448SA-32A
C= cuber
14= nominal ice capacity in 100s of pounds
48= nominal width of cabinet
S= Cube size. S=small or half dice cube.
M=medium or full dice cube
• A=Condenser type. A=air cooled. W=water
cooled
• -32=Electrical code. -32=208-230 single
phase. -3=208-230 three phase
• A=Series revision code. A=first series
Model
BH900*, B948S
BH1100,
BH1300,
BH1600
C1448,
C1848,
C2148
Direct Fit, no
adapter needed
No adapter
needed
* Note. If previously equipped with stainless steel
baffle, KBAFFLE3, remove and replace with
original plastic baffle.
Note: In some areas of this manual model numbers
Other Bins & Applications:
may include only the first five characters of the
model number, meaning that the cube size,
Note the drop zone and ultrasonic sensor locations
condenser type and voltage differences are not
in the illustrations.
critical to the information listed there.
Scotsman ice systems are designed and
manufactured with the highest regard for safety
and performance. They meet or exceed the
standards of UL and NSF.
Scotsman assumes no liability of responsibility of
any kind for products manufactured by Scotsman
that have been altered in any way, including the
use of any part and/or other components not
specifically approved by Scotsman.
Scotsman reserves the right to make design
changes and/or improvements at any time.
Specifications and design are subject to change
without notice.
November 2006
Page 3
C1448, C1848, C2148W
Air and Water Cooled User Manual
Product Description & Electrical Requirements
Dimensions
w” x d” x h”
Model
Electrical
Condenser
Minimum Circuit
Ampacity
Maximum Fuse
Size*
48 x 24 x 29
C1448SA-32
208-230/60/1
Air
17.7
30
same
C1448SW-32
208-230/60/1
Water
16.0
30
same
C1448SA-3
208-230/60/3
Air
13.6
15
same
C1448SW-3
208-230/60/3
Water
11.9
15
same
C1848SA-32
208-230/60/1
Air
25.5
30
same
C1848SW-32
208-230/60/1
Water
23.8
30
same
C1848SA-3
208-230/60/3
Air
16.5
15
same
C1848SW-3
208-230/60/3
Water
14.8
15
same
C2148SW-32
208-230/60/1
Water
22.2
30
same
C2148SW-3
208-230/60/3
Water
18.1
20
Table notes: Medium cube models have the same
electrical characteristics as Small. Series revision
code omitted.
* Or HACR type circuit breakers.
This manual covers several models. The model
number on the product is located in two places, on
the back dataplate and on the model and serial
number tag, located behind the front panel.
See the illustration for the dataplate and serial tag
locations.
Write the model and serial number of this product
here:
_________________________________________
November 2006
Page 4
C1448, C1848, C2148W
Air and Water Cooled User Manual
Cabinet Layout, Air Cooled
November 2006
Page 5
C1448, C1848, C2148W
Air and Water Cooled User Manual
Cabinet Layout, Water Cooled
November 2006
Page 6
C1448, C1848, C2148W
Air and Water Cooled User Manual
Water
The quality of the water supplied to the ice machine
will have an impact on the time between cleanings
and ultimately on the life of the product. There are
two ways water can contain impurities: in
suspension or in solution. Suspended solids can be
filtered out. In solution or dissolved solids cannot
be filtered, they must be diluted or treated. Water
filters are recommended to remove suspended
solids. Some filters have treatment in them for
suspended solids. Check with a water treatment
service for a recommendation.
Scotsman filters:
Cube ice machines use more water than what ends
up in the bin as ice. While most water is used
during ice making, a portion is designed to be
drained out every cycle to reduce the amount of
hard water scale in the machine. That’s known as
water flush, and an effective flush can increase the
time between needed water system cleaning.
In addition, this product is designed to
automatically vary the amount of water flushed
based on the purity of the water supplied to it. The
water flush rate can also be set manually.
Adjustments of flush due to local water conditions
are not covered by warranty.
A triple head filter is recommended for the potable
water. Either the Scotsman SSM3 taste and odor
filter system, or the ADS-AP3 Aqua Patrol system.
RO water. This machine can be supplied with
Reverse Osmosis water, but the water conductivity
must be no less than 10 microSiemens/cm.
Condenser Water Supply - filtration not
recommended for this water supply
GPH, 70 degree water
C1448W
70
C1848W
106
C2148W
110
Potential for Airborne Contamination
Installing an ice machine near a source of yeast or
similar material can result in the need for more
frequent sanitation cleanings due to the tendency
of these materials to contaminate the machine.
Most water filters remove chlorine from the water
supply to the machine which contributes to this
situation. Testing has shown that using a filter that
does not remove chlorine, such as the Scotsman
Aqua Patrol, will greatly improve this situation,
while the ice making process itself will remove the
chlorine from the ice, resulting in no taste or odor
impact. Additionally, devices intended to enhance
ice machine sanitation, such as the Scotsman
Aqua Bullet, can be placed in the machine to keep
it cleaner between manual cleanings
Water Flush
November 2006
Page 7
C1448, C1848, C2148W
Air and Water Cooled User Manual
Panel Removal
1
2
3
Locate and loosen the two screws at the front
edge of the top panel.
Switch Bezel
All models ship with the On and Off switches front
Pull the front panel out at the top until it clears accessible. if desired, the On and Off switches can
the top panel.
be covered up to prevent unauthorized use by
changing the bezel in the front panel's trim strip. A
Lift the front panel up and off the machine.
cover-up bezel ships loose with the machine.
4
Remove two screws at front edge of top
panel.
5
Lift up the front of the top panel, push it back
an inch, then lift to remove.
6
Locate and loosen the screw holding each
side panel to the base.
7
Pull the side panel forward to release it from
the back panel.
To change bezels: Remove the front panel and
refer to the instruction label on the inside of the
front panel. Push snaps of the standard bezel in
and pull the bezel out of the front panel. Locate
other bezel. Push into trim strip from the front until
it snaps into place. Return the front panel to its
original position and secure it to the cabinet.
5
6
1
5
Panel Removal
November 2006
Page 8
C1448, C1848, C2148W
Air and Water Cooled User Manual
Uncrate and Set Up
Begin with unpacking the ice storage bin. Remove
the carton, and using part of the carton as a
cushion, tip the bin on its back to remove the skid
and attach the legs or casters.
Bin Recycling
Many times an ice machine head will be replaced,
while the existing ice storage bin will be reused.
This is an acceptable practice, if some precautions
Note: Turn the leg levelers in all the way and adjust are taken:
after the ice machine is on top and in its selected
• The used bin must be in good condition.
location.
Broken doors, hinges, or warped walls are
reason for considering a new bin.
Return the bin to an upright position. Check the bin
• The used bin top edge gasket must be
top gasket for gaps and tears, fill any in with food
replaced. Water leaks could occur if the
grade sealant prior to placing the ice machine on
gasket tape is not replaced.
the bin.
• The used bin should be the proper size for
the ice machine head.
Install the bin top adapter if one is required for the
application.
If the ice machine has not been unpacked, do so
now. Remove the carton from the skid. Lift the ice
machine off the skid directly onto the bin.
Note: The machine is heavy! Use a mechanical
hoist if necessary.
Secure the ice machine to the bin with the
hardware provided (two metal straps and 4 bolts).
Level the bin and ice machine using the adjustment
part of the legs.
November 2006
Page 9
C1448, C1848, C2148W
Air and Water Cooled User Manual
Plumbing Requirements
All models require connection to cold, potable
water. A hand actuated valve within site of the
machine is required. Air cooled models have a
single 3/8” FPT inlet water connection, a 3/8” FPT
to 3/8” male flare adapter is supplied with the
machine and can be used if desired.
Water Filters
If connecting to water filtration, filter only the water
to the reservoir, not to the condenser. Install new
cartridges if the filters were used with a prior
machine.
A triple head filter is recommended. Either the
Scotsman SSM3 taste and odor filter system, or
the ADS-AP3 Aqua Patrol system.
Water Fitting
Inlet Water
Connection
Water cooled models have the same inlet fitting
plus an additional 3/8” FPT condenser inlet water
connection.
November 2006
Page 10
C1448, C1848, C2148W
Air and Water Cooled User Manual
Drains
3 Route the drain tubing to building drain. Follow
All models require drain tubing to be attached to
local codes for air gap.
them. Air cooled models have a single ¾” FPT
drain fitting in the back of the cabinet. Water cooled
models have the same fitting plus an additional ½” Use rigid drain tubes and then route them
FPT drain fitting in the back of the cabinet.
separately – do not Tee into the bin’s drain or, if
water cooled, Tee the condenser drain into the
reservoir or bin drain.
Install new tubing when replacing a prior ice
machine, as the tubing will have been sized for the
old model and might not be correct for this one.
Vent the reservoir drain. A vertical vent at the back
of the drain, extended about 8 – 10” will allow the
gravity drain to empty and also keep any surges
1 Connect water supply to water inlet fittings.
during draining from discharging water.
Note: This NSF listed model has a 1" anti-back flow
air gap between the end of the water inlet tube and Horizontal runs of drain tubing need a ¼” per fall
the highest possible reservoir water level, no back per foot of run for proper draining.
flow device is required for the potable water inlet.
Follow all applicable codes.
2
Connect drain tubing to drain fittings.
Water Inlet
Connection
Water Cooled
Condenser
Inlet
Potable Water
Supply
Reservoir
Drain
Optional
Water Filters
Water Cooled
Condenser
Drain
Floor Drain
Water Supply and Drain Connections
November 2006
Page 11
C1448, C1848, C2148W
Air and Water Cooled User Manual
Electrical
The machine is not supplied with a power cord, one
must either be field installed or the machine
hard-wired.
The dataplate on the back of the cabinet details the
power requirements, including voltage, phase,
minimum circuit ampacity and maximum fuse size.
HACR type circuit breakers may be used in place
of fuses. Extension cords are not permitted. Use of
a licensed electrician is recommended.
Ground Wire
Connection
Electrical connections are made inside the junction
box in the back panel of the ice machine.
1
Remove the junction box cover and route the
power cord through the access hole and
properly attach the power supply wires to the
leads in the junction box.
2
Install a field supplied strain relief per code.
Attach a ground wire to the ground connection
in the junction box.
3
Check voltage when complete.
4
Return the junction box cover to its original
position and secure with the original screws.
Power
Supply
Wires
Follow all applicable local, state and national
codes.
November 2006
Page 12
Install
Strain
Relief
C1448, C1848, C2148W
Air and Water Cooled User Manual
Final Check List
After connections,
1
Wash out the bin. If desired, the interior of the
bin could be sanitized.
2
Locate the ice scoop (if supplied) and have it
available for use when needed.
Final Check List:
1
Is the unit located indoors in a controlled
environment?
2
Is the unit located where it can receive
adequate cooling air?
3
Has the correct electrical power been supplied
to the machine?
4
Have all the water supply connections been
made?
5
Have all the drain connections been made?
6
Has the unit been leveled?
7
Have all unpacking materials been removed?
8
Is the water pressure adequate?
9
Have the drain connections been checked for
leaks?
10 Has the bin interior been wiped clean or
sanitized?
11 Have any water filter cartridges been replaced?
12 Have all required kits and adapters been
properly installed?
November 2006
Page 13
C1448, C1848, C2148W
Air and Water Cooled User Manual
Initial Start Up
1
Remove front panel. Check machine for any
packing or wires rubbing moving parts. Note
location of control board in upper left corner of
the machine’s front.
2
Remove tape securing each curtain to its
evaporator.
3
Switch on the electrical power to the machine.
Observe that some of the control’s indicator
lights glow and its display shows O.
4
Open the water supply valve.
5
Push and release the ON button. The indicator
light will begin to blink F.
The flush valve will open and the water pump will
start. The inlet water valve will open to add water to
the reservoir. After a few seconds the flush valve
will close and the water pump will stop. Water will
flow into the machine until the reservoir is full. The
hot gas valves and harvest assist devices will
activate then the compressor and water pump will
start. If its an air cooled model the fan(s) motors
will begin to turn. The display will show a
continuous F. Five seconds later the hot gas valves
will close and the harvest assist device will return
to its standby position. Warm air will be discharged
from air cooled models.
6
7
Observe the Ready for Harvest indicator light.
It may blink early in the cycle, that is normal.
The control will ignore that signal for the first 6
minutes of freeze.
During the Freeze cycle open and close the
curtains. The SW1 and SW2 lights on the
control board will blink ON when each curtain is
opened and OFF when closed.
Note: Moving a curtain during the Freeze cycle has
no affect on the control, but will cause water to flow
into the cube chute.
8
When the ice has frozen enough, the Ready for
Harvest indicator light will be on steady. After
it’s been on steady for a few seconds Harvest
will begin.
9
The display shows an H.
The hot gas valves open, the air cooled fan motors
shut off and the harvest assist mechanisms are
activated. The flush valve opens to drain some
water, when it does the inlet water valve opens to
refill the reservoir. After a few seconds the flush
valve closes but the inlet water valve continues to
fill the reservoir. Harvest continues until the ice is
released as a unit and forces the curtain to open.
When both curtains re-close the controller returns
the unit to a freeze cycle.
10 Check the ice harvested for proper bridge
thickness. The ice bridge is factory set at 3/16
inch. If needed, adjust bridge thickness. Do
NOT make it too thin.
11 Determine the water flush setting from the table
below. If desired, change the setting to
accommodate the local water conditions.
12 Return the front panel to its normal position
and secure it to the machine.
13 Instruct the user in the operation of the
machine and its maintenance requirements.
14 Fill out and mail warranty registration form.
Typical Ice Making Cycle Times (minutes).
Listed times are for clean machines in proper
installations. Cycle length at start up will be longer
until the system stabilizes.
Model
70oF. air /
50oF. water
90oF. air /
70oF. water
C1448A
12-14
14-16
C1448W
13-15
14-16
C1848A
9-11
12-14
C1848W
9-11
10-12
C2148W
9-11
10-12
November 2006
Page 14
C1448, C1848, C2148W
Air and Water Cooled User Manual
Adjustments
Bridge Thickness - For Service Tech Only
1
Push and hold Off till the machine stops.
2
Remove evaporator cover.
3
Remove curtain.
4
Use a box wrench and rotate the bridge
thickness adjustment screw in 1/8 turn
increments CW to increase bridge thickness.
Rotate CCW to decrease bridge thickness.
Caution: Do not make the bridge too thin or the
machine will not harvest properly. Bridge thickness
adjustments are not covered by warranty.
1/8 - 3/16"
bridge
Too Big
Just Right for
Small Cube
Just Right for
Medium Cube
Too Small
Ice Bridge Thickness Measurement
5
Return curtain to its normal position.
6
Push and release the On button. Check next
harvest of ice. Repeat steps 1-6 if needed.
Note: Water cooled models, the refrigeration
system discharge pressure is factory set at 245
PSIG, which should yield a freeze cycle discharge
water temperature of about 105-110 degrees F.
Adjust if necessary.
Ice Thickness Sensor
November 2006
Page 15
C1448, C1848, C2148W
Air and Water Cooled User Manual
Water flush setting
The water flush is factory set to the automatic
position, suitable for most water conditions. The
setting can be changed to one of 5 manual settings
or left on automatic.
Flush
setting
1Minimum
Water
Type
RO water
or
equivalent
Status
Power
2Moderate
4 - Heavy
Factory
Setting for
typical
water
De-Scale
Water
3Standard
Off
On
To set:
1
Switch the machine OFF by holding the Off
button in until a number or the letter A shows
on the display.
2
Press and release the On button repeatedly
until the number on the display corresponds to
the desired setting.
3
Press and release the Off switch again to
return to the normal control state.
November 2006
Page 16
5Maximum
A - Automatic
High TDS
water
Any with
conductivity not
less than 10
microSiemens/cm
C1448, C1848, C2148W
Air and Water Cooled User Manual
Use and Operation
Once started, the ice machine will automatically
make ice until the bin or dispenser is full of ice.
When ice level drops, the ice machine will resume
making ice.
Caution: Do not place anything on top of the ice
machine, including the ice scoop. Debris and
moisture from objects on top of the machine can
work their way into the cabinet and cause serious
damage. Damage caused by foreign material is not
covered by warranty.
There are four indicator lights at the front of the
machine that provide information on the condition
of the machine.
Indicator Lights:
•
•
•
•
Note: A Component Indicator Light switches ON to
indicate that the component is operating.
Power
Status
Water
Clean
Note: There are two Curtain Switch lights, SW1 and
SW2. A curtain switch light is ON when a curtain is
either open or not present.
Light indicators & their meanings
Indicator Lights & Their Meanings
Power
Status
Water
De-Scale & Sanitize
Steady Green
Normal
Normal – bin full or making ice
-
-
Blinking Green
Self Test
Failure
Switching on or off
-
-
Blinking Red
-
Diagnostic shutdown or, if making
ice, temperature sensor failure
Lack of
water
-
Yellow
-
-
-
Time to de-scale
and sanitize
Blinking Yellow
-
-
-
In Cleaning mode
Light off
No power
Switched off
Normal
Normal
All Blinking
Unit remotely locked out – check with leasing company
If the Water light is on, the machine has sensed a
lack of water. Check the water supply to the
machine. The water may have been shut off or the
water filter cartridges need to be changed.
If the Clean light is on, the machine has determined
that it may need to be cleaned. Contact an
authorized Scotsman service agent and have the
machine cleaned, de-scaled and sanitized.
November 2006
Page 17
C1448, C1848, C2148W
Air and Water Cooled User Manual
Switches
The panel in the front of the machine can be flipped Adjustable ice level control
up to access two switches – on and off.
When this option is present there is an adjustment
post and an additional indicator light to the right of
Status
De-Scale
Off
the four indicator lights mentioned above. The
ultrasonic ice level control allows the use to control
the point that the ice machine will stop making ice
before the bin or dispenser is full. Reasons for this
include:
Power
Water
On
• Seasonal changes in ice used
release the Off button. The machine will shut
• Planning to sanitize the bin
off at the end of the next cycle.
• Faster turnover for fresher ice
• To switch the machine ON, push and release
• Certain dispenser applications where
the On button. The machine will go through a
maximum ice level is not desired
start up process and then resume ice
making.
Use of control
• To switch the machine OFF, push and
Control Options
we
Lo r
There are two optional, field installed controls that
can be on this machine.
Bin
Full
Adjust Ice Level
02-4294-01 Rev. A.
• Vari-Smart (KVS) Adjustable ice level control
• SmartBoard (KSB) Advanced Feature control
VariSmart Control Area
There are several positions the ice level can be set
to, including Off (knob and label indicators lined
up), where it fills the bin until the standard bin
control shuts the machine off. See the kit’s
instructions for complete details.
Rotate the adjustment post to the desired ice level.
The machine will fill up to that level and when it
shuts off the indicator light next to the adjustment
post will be On.
Note: Ice will build up in the bin or dispenser at an
angle, the distances listed above will be from the
sensor to the top of the ice directly beneath it.
The actual distance between the highest point of
the ice may be closer or further away, depending
upon the angle of the ice.
November 2006
Page 18
C1448, C1848, C2148W
Air and Water Cooled User Manual
Options and Other Information
SmartBoard
Ice
When this option is present there is an additional
display panel in the area below the main control
board. It is not visible when the front panel is on.
The SmartBoard’s features include:
The cuber drops ice in large sections. That ice will
break up into random parts as it falls into the bin,
but some large sections may remain on top of the
ice in the bin. When removing ice, tap the groups of
ice with an ice scoop to separate them into smaller
units. In a dispenser, this ice will break up into
mostly individual cubes as the dispense
mechanism moves the ice.
• Seven day programmable ice level setting
when used with the optional Vari-Smart ice
level control
• Recording of machine operation, including
cycle time.
• Calculation of average cycle time
• Recall of malfunctions with the time they
occurred.
Air cooled models will generate heat when in
operation. That heat is discharged out the back of
the cabinet.
Noise
SmartBoard™ Advanced Feature Control
34
SEL
ESC
ENTER
See Instructions for Available Features
Heat
02-4293-01 Rev A.
The ice machine will make noise when it is in ice
making mode. The compressor, fan motors if air
cooled and water pump all produce some sound. It
is also normal to hear some cracking just before
the harvest cycle begins. In addition, during the
harvest cycle the harvest assist solenoid will click
twice as it pushes the ice out and returns to its
normal position. The ice harvests as a unit or slab,
which makes some noise when it impacts the bin or
dispenser. These noises are all normal for this
machine.
November 2006
Page 19
C1448, C1848, C2148W
Air and Water Cooled User Manual
Cleaning, Sanitation and Maintenance
This ice system requires three types of
maintenance:
• Remove the build up of mineral scale from the ice machine’s water system and sensors.
• Sanitize the ice machine’s water system and the ice storage bin or dispenser.
• Clean or replace the air filter and clean the air cooled condenser (air cooled models only).
It is the User’s responsibility to keep the ice machine and ice storage bin in a sanitary condition. Without
human intervention, sanitation will not be maintained. Ice machines also require occasional cleaning of
their water systems with a specifically designed chemical. This chemical dissolves mineral build up that
forms during the ice making process.
Sanitize the ice storage bin as frequently as local health codes require, and every time the ice machine
is cleaned and sanitized.
The ice machine’s water system should be cleaned and sanitized a minimum of twice per year.
8
Push and release the Clean button again. The
yellow Clean light will be on continuously and
the machine will drain and refill the reservoir to
flush out the ice machine cleaner and residue.
1
Remove the front panel.
2
Remove the evaporator cover.
3
If the machine is operating, push and release
9 Allow the drain and refill process to continue for
the Harvest button. When the machine
at least 20 minutes.
completes the Harvest cycle it will stop. If the
bin is full (b shows in display) push and release
10 Push and release the Off button. The clean
the Off button.
cycle will stop and the display will show O.
Remove all ice from the storage bin or
dispenser.
Note: If unit has not been de-scaled for an
4
5
extended period of time and significant mineral
Push and release the Clean button. The yellow scale remains, repeat steps 5 - 10.
Clean light will blink and the display will show
C. The machine will drain the reservoir and refill
it. Go onto the next step when the reservoir has 11 Mix a cleaning solution of 1 oz of ice machine
cleaner to 12 ounces of water.
filled.
6
Pour 24 ounces of Scotsman Nickel Safe ice
machine cleaner into the reservoir.
7
Allow the ice machine cleaner to circulate in
the water system for at least 10 minutes.
12 Locate curtains, push in on edge of curtain by
pivot pin to release it. Pull curtains out of
machine.
Push Here
Ice machine cleaner contains
acids. Acids can cause burns.
If concentrated cleaner comes
in contact with skin, flush with
water. If swallowed, do NOT
induce vomiting. Give large
amounts of water or milk. Call
Physician immediately. Keep
out of the reach of children.
November 2006
Page 20
Pull Here
C1448, C1848, C2148W
Air and Water Cooled User Manual
13 Remove water distributors from ice machine.
Inspect each distributor for restricted orifice
holes. Be sure all holes are full open.
17 Thoroughly wash all surfaces of the ice
thickness sensor, water level sensor, curtain
and water distributor with the sanitizer solution.
Squeeze Tabs Together, Slide Out Until it Stops,
Then Lift to Remove
18 Thoroughly wash all interior surfaces of the
freezing compartment, including evaporator
frames, back wall, evaporator cover and the
part of the top panel covering the freezing
compartment with the sanitizer solution.
19 Return water level sensor, ice thickness
sensor, water distributors and curtains to their
normal positions.
20 Push and hold the clean button to drain the
reservoir. Push and release the clean button
again and when the flush valve indicator light
goes out, immediately pour the remaining
cleaning solution into the reservoir.
Remove Water Distributors
21 Circulate the sanitizer solution for 10 minutes,
then push and release the Clean button.
22 Allow the water system to be flushed of
sanitizer for at least 20 minutes, then push and
release the Off button.
23 Return the evaporator cover and front panel to
their normal position and secure with the
original fasteners.
Inspect Orifice Holes
Inspect Water Distributor
14 Locate ice thickness sensor. Squeeze
mounting legs together to release sensor.
Wash the metal surfaces of the sensor and the
adjustment screw with ice machine cleaner
solution. Also wash the water distributor and
curtain with the ice machine cleaner solution.
15 Locate water level sensor. Squeeze catches
together and pull up to remove sensor. Wash
metal surfaces of sensor with ice machine
cleaner solution.
16 Mix a solution of locally approved sanitizer.
24 Push and release the On button to resume ice
making.
Ice Storage Bin
Remove and discard all ice.
Mix a solution of Scotsman Nickel Safe ice
machine cleaner and wash all interior surfaces of
the ice storage bin to remove any mineral scale
build up. Pour excess cleaner solution into the bin’s
drain.
Mix a solution of sanitizer and thoroughly wash all
Note; A possible sanitizing solution may be made
interior surfaces of the ice storage bin. Pour excess
by mixing 1 ounce of liquid household bleach with 2 sanitizer solution into the bin’s drain.
gallons of warm (95-115oF.) potable water.
November 2006
Page 21
C1448, C1848, C2148W
Air and Water Cooled User Manual
Air cooled condenser filter
1
Pull air filters from their louvered mounts.
Maintenance
2
Wash the dust and grease off the filter.
Air cooled condenser
3
Return them to their original positions.
If the machine has been operated without a filter
the air cooled condenser fins will need to be
cleaned.
Do not operate the machine without the filter in
place except during cleaning.
Push and release the Off button. Wait until the
machine stops.
If there is imbedded grease, use a commercial coil
cleaner to wash out the grease. Dust can be blown
out with compressed air from the back with a
vacuum cleaner operating in the fan area. Be
careful not to damage the condenser’s fins. Use a
fin comb to straighten any bent fins.
Exterior Panels
The front and side panels are durable stainless
steel. Fingerprints, dust and grease will require
cleaning with a good quality stainless steel cleaner.
Water filters
Filter
Filter
If the machine has been connected to water filters,
check the cartridges for the date they were
replaced or for the pressure on the gauge. Change
cartridges if they’ve been installed more than x
months or if the pressure drops too much when the
ice machine fills with water.
Air Filter Removal
November 2006
Page 22
C1448, C1848, C2148W
Air and Water Cooled User Manual
What to do before calling for service
Reasons the machine might shut itself off:
•
•
•
•
•
Lack of water.
Freeze cycle takes too long.
Harvest cycle takes too long.
High discharge temperature.
Controller self test failure.
Check the following:
1. Has the water supply to the ice machine or
building been shut off? If yes, the ice machine will
automatically restart within 25 minutes after water
begins to flow to it.
2. Has power been shut off to the ice machine? If
yes, the ice machine will automatically restart when
power is restored.
3. Has someone shut the water off to a water
cooled unit? If yes, the ice machine may need to be
manually reset.
4. Is the curtain open because some ice is stuck
under it? If so, remove the ice and the machine
should start in a few minutes.
Note: Curtain can be removed & replaced anytime
the machine is in a standby mode or when it is in a
freeze cycle. Removal of the curtain during harvest
terminates harvest at that point and, if left off, will
result in the machine shutting off.
Check For
Ice Stuck
Under Curtain
To Manually Reset the machine.
• Push and release the Off button.
• Push and release the On button.
To Shut the Machine Off:
1. Push and hold the Off button for 3 seconds or
until the machine stops.
Reset or Switch Off
November 2006
Page 23
SCOTSMAN ICE SYSTEMS
775 Corporate Woods Parkway, Vernon Hills, IL 60061
800-533-6006
www.scotsman-ice.com
17-3083-02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising