SECO-LARM USA 84-IR User manual

SECO-LARM USA 84-IR User manual
EV-1826-NKGQ (NTSC)
EV-1826-PKGQ (PAL)
84-IR LED Bullet Cameras
Manual








1 /3 ”
Sony Super HAD II CCD
2.8~12mm Varifocal lens
Weatherproof (IP66)
OSD functions accessible with
optional OSD controller (EV-18C)
Optimized to produce clear
images at night
Cables concealed in bracket
12VDC operation
Optional single-gang mounting plate
and round junction box available
Zeta Series
OSD Controller
Model No.
EV-18C
Use to access the OSD
(On-Screen Display)
functions for
compatible cameras
without having to be
near the camera.
Not included.
For more information, please see the EV-18C manual.
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
ENFORCER 84-IR LED Bullet Cameras
Specifications:
Model #
Type
CCD
# of infrared LEDs
Lens
Resolution
Pickup elements
Sync
Video output
Video output format
LEDs OFF
Minimum
illumination
LEDs ON
Gamma correction
S/N ratio
Shutter control
Gain control
IP rating
LED range
Operating voltage
LEDs OFF
Current
draw
LEDs ON
Operating temperature
Dimensions
Weight
EV-1826-NKGQ
EV-1826-PKGQ
IR LED Bullet Camera
1/3” Sony Super HAD II
84
2.8~12mm
600 TV lines
768x494 pixels
600 TV Lines
752x582 pixels
Internal
1.0Vp-p Composite video, 75Ω
NTSC
PAL
0.1 Lux
0 Lux
0.45
>45dB
Auto Electric Shutter (AES)
Auto
IP66
Up to 210ft (64m)
12VDC
130mA
660mA
130mA
660mA
14~122 F (-10~50 C)
1013/16” x 45/16” x 45/8” (275 x 116 x 118 mm)
2-lb 7-oz (2kg)
Parts List:
1 x IR camera
1 x Sunshield
1 x DC plug with
terminal block
1 x Manual
1 x Hex wrench
4 x Mounting screws
Optional EV-11LS Single-Gang Mounting Plate (Sold separately):
ENFORCER 84-IR LED Bullet Cameras can
mount to an optional single-gang mounting plate.
EV-11LS
1. Run the camera’s wires through the plate.
2. Use the 4 included mounting screws to mount
the EV-11LS single-gang plate to the wall.
3. Remove the base from the camera by twisting
4. Twist the camera into the plate until it is tight.
5. Screw the mounting arm into the plate until it is tight.
6. Tighten the adjustment nut on the camera.
7. Tighten the secure screw on the plate.
Optional EV-11LR Round Junction Box (Sold separately):
ENFORCER 84-IR LED Bullet Cameras can
mount to an optional round junction box.
EV-11LR
1. Use the mounting template (included with the
EV-11LR) to mark and drill into the wall, if necessary.
2. Use 4 mounting screws (included with the EV-11LR) to mount
the junction box to the wall.
3. Mount the camera through the foam pad (included with the
EV-11LR) to the junction box.
4. Wire can either be run through the large opening in the center
of the EV-11LR or through the conduit fittings on the side.
2
SECO-LARM U.S.A., Inc.
ENFORCER 84-IR LED Bullet Cameras
Dimensions:
45/8”
(118mm)
45/16”
(109mm)
101/4” (260mm)
1013/16” (275mm)
45/8” (116mm)
Overview:
Sunshield
screw
Mounting base
Sunshield
Camera angle
adjustment screw
Zoom
Surface mount
knock-out
Mounting arm
adjustment screw
Remove with a pair of
pliers
Mounting
arm
Focus
Adjustment
screw
Female BNC connector
DC Plug with
terminal block
DC jack
Adjustment nut
Before Starting:
1. Please read this manual carefully and keep it for
future reference.
2. Use the camera within given temperature and
electrical limits.
3. Do not aim the LED light directly at the eyes when the
LEDs are on.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong electrical
signals.
6. Do not open or disassemble the camera. There are
no field serviceable parts inside.
7. Do not drop the camera or subject it to strong
vibrations.
Installation:
1. Run a 12VDC power supply wire and a video cable
with a male BNC connector through the wall to where
the camera is to be mounted.
2. Temporarily connect the camera to the 12VDC power
supply. Do not cut the DC jack or female BNC plug
as warranty will be voided. If needed, use the
included SECO-LARM DC plug with
terminal block.
3. Temporarily connect the camera’s female BNC jack to
the video cable’s male BNC plug. While watching the
monitor, hold the camera bracket by hand against the
wall where it is to be mounted, then twist the camera
until it is certain that this mounting location is correct.
Use a pencil to mark the location of the four screw
holes in the bracket.
SECO-LARM U.S.A., Inc.
4. Disconnect the 12VDC power supply and video cable.
5. Mount the bracket to the wall using the four included
mounting screws.
6. If mounting to the EV-11LR or EV-11LS, see instructions
on page 2.
7. Reconnect the 12VDC power supply and video cable.
Turn the monitor on and make sure the camera is
sending the proper video signal.
8. To adjust the camera angle, loosen and tighten the
adjustment nut, or loosen and tighten either of the two
screws on the mounting arm. Adjust until the desired
scene is displayed.
9. Adjust the zoom and focus using the included hex
wrench.
10. Do a final test of the video camera and monitor.
3
ENFORCER 84-IR LED Bullet Cameras
Troubleshooting:
The screen is blank.




Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim.
 Clean the lens using a soft, clean, dry, and lint-free cloth.
 Check that the light source is adequate.
The screen image has poor contrast.
 Adjust the monitor’s contrast knob.
 Change the position of the camera.
The screen image flickers.
 Change the position of the camera.
The screen image is distorted.
 Change the position of the camera.
The camera case is hot.
 Check that the correct power supply is in use.
IR LEDs do not turn on.
 Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service
for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications
without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: [email protected]
4
PICSN5
MiEV-1826-xKGQ_1206.docx
SECO-LARM U.S.A., Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement