SECO-LARM USA 3x User manual

SECO-LARM USA 3x User manual
Elite 3X Vandal Dome Cameras
For Flush or Surface Mount
Installation Manual
EV-2866-NKGQ
EV-2866-PKGQ
NTSC
PAL
3 Cameras in 1:
1 /3 ”
Sony Super HAD II CCD
600 TV Lines
12VDC/24VAC
2.8~12mm Varifocal lens
256x Digital slow shutter
On-screen display (OSD)
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.
Elite 3X Vandal Dome Cameras for Flush or Surface Mount
Specifications:
Type
Video Output Mode
Pickup Element
Resolution
Lens (Varifocal)
# of Infrared LEDs
Effective Pixels
Video Output
Minimum Illumination
S/N ratio
On Screen Display (OSD)
Motion Detection
Backlight Compensation
White Balance
Digital Slow Shutter (DSS)
Electronic Shutter
Auto Gain
3-DNR (DNR with 3D filtering)
Day & Night (color)
Sharpness
Privacy
IP Rating
Operating Voltage
LEDs OFF
Current Draw
LEDs ON
Operating Temperature
Dimensions
Weight
EV-2866-NKGQ
EV-2866-PKGQ
IR LED Dome Camera
NTSC
PAL
1/3” Sony Super HAD II CCD
600 TV Lines
2.8~12mm
33 (850nm)
768x494 pixels
752x582 pixels
1Vp-p composite video, 75Ω
0.00006 Lux (LEDs ON)
0.05 Lux (LEDs OFF)
>52dB (AGC OFF)
Built-in and controlled by internal joystick
4 zones
HLC/BLC/Off
ATW / AWC / MANUAL
256x
Auto/Manual (adjustable range: 1/60~1/120,000 sec)
Selectable: Low, Middle, High, Off
On/Off
Selectable: Color, Auto, B/W
On/Off (adjustable range: 0~31)
On/Off (8 programmable zones)
IP68
12VDC/24VAC Dual Voltage
12VDC: 200mA / 24VAC: 3.6W
12VDC: 500mA / 24VAC: 9W
-14°~122° F (-10°~50° C)
51/2”x315/16” (140x100 mm)
With base: 2-lb 10-oz (1,191g)
Without base: 1-lb 15-oz (879g)
Parts List:
1 x Manual
1 x Camera
1 x Hex wrench
4 x Hex screws
4 x Mounting screws
4 x Base-mounting screws
1
Dimensions:
4 5 /8 ”
(118mm)
51/2”(140mm)
315/16”
(100mm)
2
1 x Service monitor port connector
1 x DC plug with terminal block
1 x Flush-mounting template
3 3 /4 ”
(95mm)
2 3 /8 ”
(60mm)
SECO-LARM U.S.A., Inc.
Elite 3X Vandal Dome Cameras
Overview:
OSD joystick
Service
monitor port
BNC
connector
Camera
Set screw
Dome
Base
(For surface mounting only)
Rubber ring
DC Plug to
terminal block
DC Jack
Important:
Do not cut the DC jack or the female BNC
connector as this will void the warranty.
Before Starting:
1. Please read this manual carefully and keep it for future
reference.
2. Use the camera within given temperature and electrical
limits.
3. Do not aim the LEDs directly at the eyes when the LEDs
are on.
4. Do not point the camera at the sun. Heat could damage
the camera, even when not in use.
5. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong electrical
signals.
6. Do not open or disassemble the camera. There are no
field-serviceable parts inside.
7. Do not drop the camera or subject it to strong
vibrations.
Installation:
1. Run hidden cables from the video source and power
supply and connect to the camera. Do not cut the DC
jack or female BNC connector as this will void the
warranty. If needed, use the included SECO-LARM
DC plug with terminal block.
2. Test the voltage from the power supply.
Use 12VDC or 24VAC.
3. Undo the hex screws on the side of the dome using the
included allen wrench and remove the dome and the
rubber ring from the camera and base.
4. For surface mounting:
Hold the camera against the wall, ceiling, or other
mounting surface while watching the monitor to find the
best mounting location. Mark that location with a
pencil. Mount the base to the wall or ceiling using the
four included mounting screws. If the wall is made of
brick, drywall, or similar material, it may be necessary
to use screw anchors (not included).
Mount the camera to the base using the base-mounting
screws.
SECO-LARM U.S.A., Inc.
5.
6.
7.
8.
9.
10.
For flush mounting:
Use the included mounting template as a guide to
drill the necessary holes. Insert the camera into
the hole. Mount the camera to the wall using the
four included mounting screws.
Adjust the camera angle as needed. Use the
OSD control joystick to adjust the camera settings
(See the OSD manual). Connect a service
monitor to the service monitor port connector for
on-site adjustments.
To adjust zoom and focus, loosen the lock knobs
by hand or with a screwdriver. Slide left or right to
adjust. Do not use power tools. Lens damage
may result
Replace the rubber ring on the camera.
Reattach the dome to the camera.
Use the included allen wrench to tighten the set
screw, securing the dome to the base.
Do a final test of the video camera and monitor.
3
Elite 3X Vandal Dome Cameras for Flush or Surface Mount
Troubleshooting:
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image has poor contrast.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers.
Change the position of the camera.
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
Check that the correct power supply is in use.
IR LEDs do not turn on.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of three (3) years from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement
of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326
4
Website: www.seco-larm.com
E-mail: [email protected]
PIKHR1
MiEV-2866-xLGxQ_1110.docx
SECO-LARM U.S.A., Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement