SECO-LARM USA EV-122C-DXA3 User manual

SECO-LARM USA EV-122C-DXA3 User manual
ENFORCER BALL-MOUNT IR DOME CAMERA Manual
ENFORCER BALL-MOUNT IR DOME CAMERA Manual
R
E
C
R
O
O
E
F
D
I
V
EN
®
TROUBLE SHOOTING
The screen is blank
• Check that the camera is powered up.
• Check that the monitor is powered up.
• Check that the video cable connecting the camera to the monitor is connected properly.
The screen image is dim
• Clean the lens (using a soft, clean cloth).
• Check that the light source is adequate.
The screen image has poor contrast
• Adjust the monitor’s contrast knob.
• Change the position of the camera.
The screen image flickers
• Change the position of the camera.
The screen image is distorted
• Change the position of the camera.
The camera case is hot
• Check that the correct power supply is in use.
MANUAL
IMPORTANT Users and installers of this product are responsible for ensuring this product complies with all national,
state, and local laws and statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held
responsible for the use of this product in violation of any current laws or statutes.
WARNING Stop using the camera if you see a malfunction like smoke or unusual heat, as it could cause fire or
electric shock. Do not open the case of this device, as there are no field-serviceable components inside.
EV-122C-DXA3
1/3” CCD Color Ball-Mount
IR Dome Camera
FCC COMPLIANCE STATEMENT Information to the user: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own expense.
WARRANTY This SECO-LARM product is warranted against defects in material and workmanship while used in normal
service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is
limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect,
repair, or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines
that such equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential
personal or property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2007 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or
in part, without the written permission of SECO-LARM.
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco-larm.com
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: [email protected]
®
PITCW1
iMUBallMountCam.PMD
SECO-LARM®
ENFORCER BALL-MOUNT IR DOME CAMERA Manual
Specifications
EV-122C-DXA3 (NTSC)
Type
Color camera
Chip
1/3” CCD, Sony
Resolution
420 TV lines
Pickup elements
510 x 492 pixels
Scanning system
2:1 interlace, V: 59.94Hz, H: 15.734KHz
Sync
Internal
Video output
1V pp composite output, 75 ohms
Lens
F1.2, 3.6mm (lens included)
IR LEDs
24 x LEDs
IR distance
Up to 50’ (15m)
IR view angle
50o~80o beam spread, 30o per LED
Minimum illumination
0.05 lux, (0 lux with IR on)
Gamma correction
0.45
S/N ratio
>50dB
Shutter control
Auto Electronic Shutter (AES), 1/60~1/100,000 sec.
Backlight compensation
Auto
Automatic gain control
Auto
White balance
Auto, 2500o ~ 9500oK
Power source
12VDC ±10%
Power consumption
70mA (IR off), 280mA (IR on)
Storage temperature
-22°~140° F (-30°~60° C)
Operating temperature
14°~122° F (-10°~50° C)
Dimensions
311/16” x 211/16” (93 x 69mm)
Weight
6.3 oz. (180g)
Parts List
EVA-F5521-3 -- Optional power cord. For easy
connection of dome or bullet camera to power supply.
1 x Camera Ball
1 x Case (2-part construction)
1 x Base
3 x Screws
1 x Manual
To BNC
(3-ft. wire length)
(From DC
Camera)
(EVA-F5521-3)
Power
Connector
3x
Screws
BNC
Connector
Case
Case
Camera
Ball
Base
BEFORE STARTING
1. Please read this manual carefully and keep it for future reference.
2. Use the camera within given temperature and electrical limits.
3. Do not mount the camera where it is exposed to rain or other
moisture, or in humid or dusty places.
4. Do not point the camera at the sun. Heat could damage the
camera, even when not in use.
5. Do not mount the camera in areas exposed to radiation, strong
magnetic fields, or strong electrical signals.*
Dimensions:
211/16”
(69mm)
311/16” (93mm)
ENFORCER BALL-MOUNT IR DOME CAMERA Manual
INSTALLATION
1. Run a 12VDC power supply wire and a video cable with a male
BNC connector through the wall to where the camera is to be
mounted.
2. Temporarily connect the camera to the 12VDC power supply.
3. Temporarily connect the camera’s female BNC connector to the
video cable’s male BNC connector.
4. While watching the monitor, hold the camera against the wall
by hand where it is to be mounted, then turn the camera until it
is certain that this mounting location is correct. Use a pencil to
mark the location of the three screw holes in the base.
5. Disconnect the 12VDC power supply and video cable.
6. Do not open or disassemble the camera. There are no userserviceable parts inside.
7. Do not drop the camera or subject it to strong vibrations.
* Note: Many video monitors produce strong electromagnetic
fields close to the display CRT, especially when the monitor is
turned on or during de-Gaussing, which occurs automatically
with many monitors when the monitor is turned on.
6. Mount the bracket to the wall using the three included mounting
screws. If the wall is made of dry wall, brick, or similar material,
it may be necessary to use screw anchors (not included).
7. Reconnect the 12VDC power supply and video cable. Turn the
monitor on, and make sure the camera is sending the proper
video signal.
8. Adjust the camera angle.
9. Put the case over the camera ball and twist to secure to the
base.
10. Do a final test of the video camera and monitor.
* Note: The base also allows flush-mounting of the camera.
However, for the best security, run the wires through the wall.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement