SECO-LARM USA EV-2125-N2WQ User manual

SECO-LARM USA EV-2125-N2WQ User manual
EV-2125-N2WQ (NTSC)
EV-2125-P2WQ (PAL)
Mini Vandal Dome Camera
Manual
1 /3 ”
Sony Super HAD II CCD
2.9mm lens
420 TV lines
Small 3” (76mm) diameter
Weatherproof (IP65)
Vandal-resistant design
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
ENFORCER Mini Vandal Dome Camera
Specifications:
Type
CCD
Resolution
Lens size
Pickup elements (HxV)
Sync
Video output
Video output format
S/N ratio
Shutter control
Gamma correction
Gain control
Minimum illumination
Operating voltage
Current draw
Operating temperature
Dimensions
Weight
EV-2125-N2WQ
EV-2125-P2WQ
Ultra-Mini Vandal Dome Camera
1/ ” Sony Super HAD II
3
420 TV lines
2.9mm
510x492 pixels
500x528 pixels
Internal
1Vp-p composite video, 75Ω
NTSC
PAL
>48dB (AGS OFF)
Auto Electric Shutter (AES)
0.45
Auto
0.1 Lux/F1.2
12VDC ±10%
60mA
-4°~122° F (-20°~50° C)
3”x23/8” (76x60 mm)
6.4-oz (182g)
Parts List:
1 x Manual
1 x Camera
3 x Mounting screws
3 x Screw anchors
Dimensions:
1 x Allen wrench
1x Rubber seal
1 x DC plug with
terminal block
1 x Allen wrench
Applying the Rubber Seal:
213/16”
(72mm)
Rubber seal
2 3 /8 ”
(60mm)
If using the camera outdoors, use the
rubber seal. To use, remove the backing
and apply to the camera base.
2
SECO-LARM U.S.A., Inc.
ENFORCER Mini Vandal Dome Camera
Overview:
Camera
Set screw
Dome cover
Mounting base
Wiring notch
Female BNC connector
DC plug with
terminal block
DC jack
Mounting screw
Important:
Do not cut DC jack or female BNC connector
as warranty will be voided.
Before Starting:
1. Please read this manual carefully and keep it
for future reference.
2. Use the camera within given temperature and
electricity limits.
3. Do not point the camera at the sun. Heat could
damage the camera, even when not in use.
4. Do not mount the camera in areas exposed to
radiation, strong magnetic fields, or strong
electrical signals*
5. Do not drop the camera or subject it to
strong vibrations.
Note: Many video monitors produce strong
electromagnetic fields close to the display
CRT, especially when the monitor is turned
on or during de-gaussing, which occurs
automatically with many monitors when
turned on.
Installation:
1. Run hidden cables from the video source and
12VDC power supply to the camera. Do not
cut the DC jack or female BNC connector as
this will void the warranty. If needed, use the
included SECO-LARM DC plug with
terminal block.
2. Test to make sure the voltage is correct.
Use only 12VDC.
3. Undo the set screw on the side of the dome
cover using the included allen wrench and
remove the dome from the base.
4. If mounting outdoors, apply the rubber seal to
the base as shown on page 2, Applying the
Rubber Seal.
SECO-LARM U.S.A., Inc.
5. Hold the camera against the wall, ceiling, or
other mounting surface while watching the
monitor to find the best mounting location.
Mark that location with a pencil.
6. Mount the mounting base to the wall using
the 3 included mounting screws. If
necessary, use the included screw anchors.
7. Adjust the camera angle as needed.
8. Test the video signal.
9. Reattach the dome cover to the camera.
10. Use the included allen wrench to tighten the
set screw, securing the dome to the base.
11. Do a final test of the video camera and
monitor.
3
ENFORCER Mini Vandal Dome Camera
Troubleshooting:
The screen is blank.
Check that the camera is powered up.
Check that the power supply’s polarity is correct.
Check that the monitor is powered up.
Check that the video cable connecting the camera to the
monitor is connected properly.
The screen image is dim.
Clean the lens using a soft, clean cloth.
Check that the light source is adequate.
The screen image has poor contrast.
Adjust the monitor’s contrast knob.
Change the position of the camera.
The screen image flickers.
Change the position of the camera.
The screen image is distorted.
Change the position of the camera.
The camera case is hot.
Check that the correct power supply is in use.
IMPORTANT
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.
WARNING
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open
the case of this device, as there are no field-serviceable components inside.
FCC COMPLIANCE STATEMENT
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his or her own expense.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for a
period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of
any defective part if the unit is returned, transportation prepaid, to SECO-LARM.
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment is
not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.
NOTICE
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,
without the written permission of SECO-LARM.
SECO-LARM U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Tel: 800-662-0800 / 949-261-2999
4
Website: www.seco-larm.com
E-mail: [email protected]
PICSN4
mi-EV-2125-x2WQ-1103.docx
SECO-LARM U.S.A., Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement