Shark | HP-5030D | User's Manual | Shark HP-5030D User's Manual

Shark HP-5030D User's Manual
Model: HP
operating instruction
and parts manual
HP-5030D
For technical assistance or the SHARK dealer nearest you
visit our website at www.shark-pw.com
97-6133
CONTENTS
Introduction
4
Important Safety Information
4-5
Installation
5,7
Component Identification
6
Starting and Operating Instructions
7
Preventative Maintenance
7
Maintenance and Service
8-9
Field Service of Fuel Pump
9
Machine Assembly Exploded View
10
Machine Assembly Exploded View Parts List
11
Burner Assembly, Exploded View
12
Burner Assembly Exploded View Parts Lists
13
Troubleshooting
14-15
Preventative Maintenance 16
Warranty
Model Number ______________________________
Serial Number ______________________________
Date of Purchase ____________________________
The model and serial numbers will be found on a decal attached
to the machine. You should record both serial number and date of
purchase and keep in a safe place for future reference.
97-6133 • Rev. 5/07
PRESSURE WASHER
OPERATOR’S MANUAL
INTRODUCTION & Important Safety Information
All information in this manual is based on the latest
product information available at the time of printing.
This machine is designed to heat water from a cold
water pressure washer. Maximum water flow is 5 GPM
and maximum pressure is 3000 PSI. Flow rate of 3
GPM will achieve an average temperature of about
180°F. Temperature is dependent on inlet water temperature and water flow rate.
We reserve the right to make changes at any time
without incurring any obligation.
Owner/User Responsibility:
The owner and/or user must have an understanding of
the manufacturer’s operating instructions and warnings
before using this hot water generator. Warning information should be emphasized and understood. If the
operator is not fluent in English, the manufacturer’s instructions and warnings shall be read to and discussed
with the operator in the operator’s native language by
the purchaser/owner, making sure that the operator
comprehends its contents.
Owner and/or user must study and maintain for future
reference the manufacturers’ instructions.
This manual should be considered a permanent
part of the machine and should remain with it
if machine is resold.
When ordering parts, please specify model
and serial number.
important SAFETY
information
CAUTION: To reduce the risk of
CAUTION injury, read operating instruc-
read operator’s
manual thoroughly
prior to use.
tions carefully before using.
1.Read the owner’s manual
thoroughly. Failure to follow
instructions could cause
malfunction of the machine
and result in death, serious
bodily injury and/or property
damage.
2.All installations must comply with local codes.
Contact your electrician, plumber, utility company
or the selling distributor for specific details.
To comply with the National Electrical Code (NGPA
70) and provide additional protection from risk of
electric shock, this hot water generator is equipped
with a UL approved ground fault circuit interrupter
(GFCI) power cord.
WaRNiNg
risk of fire.
do not use with
flammable liquids.
WARNING: Flammable liquids
can create fumes which can
ignite causing property damage
or severe injury.
WARNING: Do not use gasoline, crankcase drainings or oil
containing gasoline, solvents
or alcohol. Doing so will result
in fire and/or explosion.
WARNING: Do not spray flammable liquids. Operate only where an open torch is permitted.
3.This fuel burning machine shall be installed only in
locations where combustible dusts and flammable
gases or vapors are not present.
4.In these oil burning models, use only kerosene,
No. 1 home heating fuel, or diesel fuel.
WARNING: Keep water spray,
wand and high pressure hose
away from electric wiring or
fatal electric shock may result.
Read warning tag on electrical
cord.
5.To help protect the operator
keep water spray
away from
from electrical shock, the
electrical wiring.
machine must be electrically
grounded. It is the responsibility of the owner
to connect this machine to a UL grounded
receptacle of proper voltage and amperage ratings. Do not spray water on or near electrical components. Do not touch machine with wet hands or
while standing in water. Always disconnect power
before servicing.
WaRNiNg
WARNING: Spray gun kicks back — hold attached
pressure washer with both hands.
6.Grip cleaning wand of attached pressure washer
securely with both hands before starting cleaner.
Failure to do this could result in injury from a whipping wand.
WaRNiNg
WARNING: High pressure
stream of fluid that this equipment can produce can pierce
the skin and its underlying tissues, leading to serious injury
and possible amputation.
Note: The heating module
does not produce pressure.
Pressure is developed from attached pressure washer.
7. High pressure developed by the attached pressure
washer can cause bodily injury or damage.
high pressure
spray can pierce
skin and tissues.
97-6133 • Rev. 5/07
Use caution when operating. Do not point the spray
gun from the attached pressure washer at anyone
or at any part of the body. This machine is to be
used only by qualified operators.
8.Never make adjustments on machine while it is in
operation.
WaRNiNg
WaRNiNg
risk of
asphyxiation.
use only in a well
ventilated area.
WARNING: Risk of asphyxiation
— Use this product only in a
well ventilated area.
10. When the machine is operating, do not cover or place in a
closed space where ventilation is insufficient.
WARNING: Risk of fire — Do
not add fuel when the machine
is operating or still hot.
11. Attached pressure washer
with a spray gun should not
be operated with the spray
risk of fire.
gun in the off postion for
do not add fuel
extended periods of time as
when operating
machine.
this may cause damage to
the pump.
Check to make sure burner shuts off when spray
gun trigger is closed.
WaRNiNg
OPERATOR’S MANUAL
protective
eyewear and clothing must
be worn.
WARNING: High pressure spray
from attached pressure washer
can cause paint chips or other
particles to become airborne
and fly at high speeds.
9. Eye safety devices must be
worn when using this equipment.
12.Protect from freezing.
13.To prevent a serious injury, make certain quick
coupler on discharge hose has locked before using
pressure washer.
14.Do not allow acids, caustic or abrasive fluids to
pass through the machine.
15.Inlet water must be from a cold water pressure
washer (3,000 PSI maximum).
16.Do not allow CHILDREN to operate the pressure
washer at any time. THIS MACHINE MUST BE
ATTENDED DURING OPERATION.
17.The best insurance against an accident is precaution and knowledge of the machine.
18.Do not operate this product when fatigued or under
the influence of alcohol or drugs. Keep operating
area clear of all persons.
19. We will not be liable for any changes made to
our standard machines, or any components not
purchased from us.
20.Do not overreach or stand on unstable support.
Keep good footing and balance at all times.
21. Follow the maintenance instructions specified in
the manual.
22. When making repairs disconnect from electrical
source.
23.Turn burner off and open spray gun to allow water
to flow and cool coil to 100°F before turning machine off.
24. Before disconnecting high pressure hose from
machine water outlet, open spray gun to relieve
back pressure in hose.
PRESSURE WASHER
Important Safety Information
Caution: This machine produces hot water and
must have insulated components attached to protect the operator.
97-6133 • Rev. 5/07
PRESSURE WASHER
Component Identification
CAUTION HOT WATER:
Must use insulated spray
gun and wand.
OPERATOR’S MANUAL
Pressure Washer
3,000 PSI Maximum
(not included)
Pressure Washer Coupler
Fresh Water
Faucet
Garden Hose
(not included)
Diesel
Fuel
Tank
Insulated Wand
(not included)
Insulated
Spray Gun
(not included)
Pressure Washer
to Inlet Hose
Outlet
Connection
Inlet
Connection
Power Cord
High Pressure Outlet Hose
(not included)
GFCI
97-6133 • Rev. 5/07
Place machine in a convenient location providing
ample support, drainage and room for maintenance.
Remove bolts from pallet to foot bracket. Install rubber
feet provided as shown in exploded view.
Placement:
Location:
Local code will require certain distances from floor
and walls. (Two feet away from walls should be adequate.)
1.This machine should be run on a level surface
where it is not readily influenced by outside sources such as strong winds, freezing temperatures,
rain, etc. It should be located to allow accessibility
for refilling of fuel, adjustments and maintenance.
Normal precautions should be taken by the operator of the machine to prevent moisture from
reaching the electrical controls.
2.It is recommended that a partition be made between the wash area and the machine to prevent
water spray from coming in contact with the
machine. Excess moisture reaching any electric
components or electrical controls will reduce machine life and may cause electrical shorts.
3.During installation of the machine, beware of
poorly ventilated locations or areas where exhaust
fans may cause an insufficient supply of oxygen.
Sufficient combustion can only be obtained when
there is a sufficient supply of oxygen available for
the amount of fuel being burned. If it is necessary
to install a machine in a poorly ventilated area, outside fresh air may have to be piped to the burner
and a fan installed to bring air into the machine.
Allow enough space for servicing the machine.
Water Source:
The water source for the pressure washer should be
supplied by a minimum 5/8” I.D. garden hose with a
city water pressure of not less than 30 PSI. If the water
supply is inadequate, or if the garden hose is kinked,
the attached pressure washer will run very rough and
the burner will not fire.
Connection:
OPERATOR’S MANUAL
The location should protect the machine from damaging environmental conditions, such as; wind, rain, and
freezing.
Do not locate near any combustible material. Keep all
flammable material at least 20 feet away.
PRESSURE WASHER
Installation
See Component Identification.
Venting:
Adding exhaust vent pipe to your oil fired burner is
not recommended because restricted air flow causes
carbon build-up, which affects the operation, and increases maintenance on the coil. If a stack must be
used, refrain from using 90° bends. If the pipe can not
go straight up then use only 45° bends and go to the
next size pipe. The overall pipe length must not exceed
6 feet in length. The burner air adjustment must be
performed after vent pipe is installed. Use a smoke
tester for proper air setting.
Electrical:
This machine, when installed, must be electrically
grounded in accordance to local codes. Check for
proper power supply using a volt meter.
97-6133 • Rev. 5/07
OPERATOR’S MANUAL PRESSURE WASHER
Operating Instructions
STEP 1: Check fuel tank and pump
oil levels on both machines and
connect garden hose to pressure
washer. CAUTION: Only use fresh
water to this machine.
STEP 2: Attach high pressure hose
between pressure washer and machine. Turn garden hose water on.
Additional adapters and couplers
may be needed to connect your
brand of pressure washer to the
machine.
Burner
Switch
STEP 4: For hot water washing,
turn the machine burner switch to
the ON position. Adjust thermostat
to desired temperature setting. (The
burner will light automatically.)
97-6133 • Rev. 5/07
STEP 4: Connect the power cord
into the proper electrical outlet,
then push in the GFCI reset button.
Start up attached pressure washer
according to the manufacturers instructions. When a steady stream of
water flows from the spray gun and
wand the machine is ready for cold
water cleaning.
WaRNiNg
WARNING: Some detergents
may be harmful if inhaled or
ingested, causing severe nausea, fainting or poisoning. The
harmful elements may cause
property damage or severe
injury.
STEP 2: With the motor running,
pull trigger to operate machine.
Liquid detergent is drawn into the
machine and mixed with water.
Apply detergent to work area.
Do not allow detergent to dry on
surface.
IMPORTANT: You must flush the detergent injection system after each use by placing the suction
tube into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes.
Recommendations:
OPERATOR’S MANUAL
STEP 1: Use detergent designed
specifically for pressure washers.
Household detergents could damage the pump. Prepare detergent
solution as required by the manufacturer. Fill a container with pressure washer detergent. Place the
filter end of detergent suction tube
into the detergent container.
cleaning tips
Pre-rinse cleaning surface with fresh water. Place detergent suction tube directly into cleaning solution and
apply to surface at low pressure (for best results, limit
your work area to sections approximately 6 feet square
and always apply detergent from bottom to top). Allow
detergent to remain on surface 1-3 minutes. Do not
allow detergent to dry on surface. If surface appears
to be drying, simply wet down surface with fresh water.
If needed, use brush to remove stubborn dirt. Rinse at
high pressure from top to bottom in an even sweeping
motion keeping the spray nozzle approximately 1 foot
from cleaning surface. Use overlapping strokes as you
clean and rinse any surface. For best surface cleaning
action spray at a slight angle.
PRESSURE WASHER
detergents and general operating techniques
• Before cleaning any surface, an inconspicuous
area should be cleaned to test spray pattern and
distance for maximum cleaning results.
• If painted surfaces are peeling or chipping,
use extreme caution as pressure washer may
remove the loose paint from the surface.
• Keep the spray nozzle a safe distance from the
surface you plan to clean. High pressure wash
a small area, then check the surface for damage. If no damage is found, continue to pressure
washing.
CAUTION - Never use:
• Bleach, chlorine and other corrosive chemicals
• Liquids containing solvents (i.e., paint thinner,
gasoline, oils)
• Trisodium phosphate products
• Ammonia products
• Acid-based products
These chemicals will harm the machine and will damage the surface being cleaned.
rinsing
It will take a few seconds for the detergent to clear.
Apply safety latch to spray gun. Remove black soap
nozzle from the quick coupler. Select and install the
desired high pressure nozzle. NOTE: You can also stop
detergent from flowing by simply removing detergent
siphon tube from bottle.
97-6133 • Rev. 5/07
OPERATOR’S MANUAL PRESSURE WASHER
shutting down and clean-up
Burner
Switch
STEP 1: If using an optional detergent injector,
place the detergent line in
a bucket of water allowing
detergent to be flushed
from system.
STEP 2: Tur n bur ner
switch off and continue
spraying water, allowing
the water to cool. After
water has cooled to less
than 100°F, turn the attached pressure washer
off.
STEP 3: Turn garden hose
water off. Open the spray
gun to relieve remaining
pressure.
STORAGE
CAUTION: Always store your pressure washer in a
location where the temperature will not fall below
32°F (0°C). The pump in this machine is susceptible
to permanent damage if frozen. FREEZE DAMAGE
IS NOT COVERED BY WARRANTY.
1.Stop the pressure washer, squeeze spray gun
trigger to release pressure.
2.Detach water supply hose and high pressure
hose.
3.Turn on the machine for a few seconds, until remaining water exits. Turn engine off immediately.
4.Drain the gas and oil from the engine.
5.Do not allow high pressure hose to become
kinked.
6.Store the machine and accessories in a room
which does not reach freezing temperatures.
CAUTION: Failure to follow the above directions will
result in damage to your pressure washer.
When the pressure washer is not being operated or is
being stored for more than one month, follow these
instructions:
4.Cover the pressure washer and store in a clean, dry
place that is well ventilated away from open flame
or sparks. NOTE: The use of a fuel additive, such
as STA-BIL®, or an equivalent, will minimize the
formulation of fuel deposits during storage. Such
additives may be added to the gasoline in the fuel
tank of the engine, or to the gasoline in a storage
container.
After Extended Storage
CAUTION: Prior to restarting, thaw out any
possible ice from pressure washer hoses,
spray gun or wand.
Engine Maintenance
During the winter months, rare atmospheric conditions
may develop which will cause an icing condition in the
carburetor. If this develops, the engine may run rough,
lose power and may stall. This temporary condition can
be overcome by deflecting some of the hot air from the
engine over the carburetor area. NOTE: Refer to the
engine manufacturer’s manual for service and maintenance of the engine.
1.Replenish engine oil to upper level.
2.Drain gasoline from fuel tank, fuel line, fuel valve
and carburetor.
3.Pour about one teaspoon of engine oil through
the spark plug hole, pull the starter grip several
times and replace the plug. Then pull the starter
grip slowly
until you feel increased pressure which indicates
the piston is on its compression stroke and leave
it in that position. This closes both the intake and
exhaust valves to prevent rusting of cylinder.
10
97-6133 • Rev. 5/07
problem
possible cause
solution
burner will not
light
Disconnected or short in electrical
wiring
All wire contacts should be clean and tight.
No breaks in wire.
Burner motor thermal protector
tripped
If tripped, check voltage, connections and
extensions for cause. Check fuel pump
shaft rotation for binding, causing motor to
overheat.
On/off switch defective
Check continuity through burner switch.
Heavy sooting on coil and burner,
can cause interruption of air flow
and shorting of electrodes
Clean as required.
Improper electrode setting
Clean and test according to diagram in
operator’s manual.
Fuel not reaching combustion cham- Check fuel pump for proper flow. Check
ber
solenoid flow switch on machines with spray
gun control for proper ON/OFF flow switch.
Machine smokes
Fuel solenoid malfunction
Check by placing screwdriver inside coil
then turn machine on, open spray gun and
check for magnetic pull.
Clogged burner nozzle
Replace.
Water not turned on
Turn on water to activate burner flow switch.
Flow switch malfunction
Remove, test for continuity and replace as
needed.
Improper fuel or water in fuel
Drain tank and replace contaminated fuel.
Low fuel pressure
Adjust fuel pump pressure to specifications.
Air leaks in fuel lines
Check fuel lines for leaks or air bubbles.
Tighten or replace as needed.
Plugged or dirty burner nozzle
Replace.
Faulty burner nozzle spray pattern
Replace nozzle.
Heavy accumulation of soot on coils
and burner assembly
Remove coils and burner assembly. Clean
thoroughly.
Misaligned electrode
Realign electrodes to specifications.
Fuel filter partially clogged
Replace as needed.
Obstruction in smoke stack
Check for insulation blockage or other foreign objects.
Soot build-up on coils
Clean coils with soot remover.
Lime build-up in coils
Clean inside of coils using coil cleaner.
PRESSURE WASHER Troubleshooting Guide
troubleshooting
11
97-6133 • Rev. 5/07
PRESSURE WASHER Troubleshooting Guide
troubleshooting
problem
possible cause
solution
low water
temperature
Improper fuel or water in fuel
Drain fuel tank and replace with
proper fuel.
Low fuel pressure
Increase fuel pressure.
Weak fuel pump
Check fuel pump temperature. Replace pump if needed.
Fuel filter partially clogged
Replace as needed.
Soot build up on coils
Clean coils with soot remover.
Lime build up on coils
Clean inside of coils using coil
cleaner.
Improper burner nozzle
See specifications.
water
temperature
too hot
Incoming water to machine warm or hot Lower incoming water temperature.
Fuel pump pressure too high
Lower fuel pressure.
Fuel pump defective
Replace fuel pump.
Detergent line sucking air
Tighten all clamps. Check detergent
line for holes.
Defective high limit switch (thermostat)
Replace.
Incorrect fuel nozzle size
See Burner Nozzle section.
Insufficient water supplied
Check GPM to machine.
Restricted water flow
Check nozzle for obstruction, proper
size.
PREVENTATIVE MAINTENANCE
MAINTENANCE SCHEDULE
Machine
Clean
Daily
Water Lines
Check
Daily
Fittings
Check
Daily
Fuel Filter
Clean
Weekly
Inlet Strainer
Clean
Weekly
Fuel Nozzle
Clean
Weekly
Fuel Tank
Clean
Weekly
Electrodes
Adjust
Monthly
Fuel Pump Strainer
Clean
Monthly
Electrode Wires
Check
Monthly
12
97-6133 • Rev. 5/07
The areas around the machine should be kept clean
and free of combustible materials, gasoline and other
flammable vapors and liquids.
The flow of ventilating air to the burner must not be
blocked or obstructed in any manner.
MAINTENANCE AND SERVICE
Winterizing Procedure:
Damage due to freezing is not covered by warranty.
Adhere to the following cold weather procedures whenever the washer must be stored or operated outdoors
under freezing conditions.
During winter months, when temperatures drop below 32°F, protecting your machine against freezing
is necessary. Store the machine in a heated room. If
this is not possible use compressed air on the short
hose end. By injecting compressed air, all water will
be blown out of the system. Run anti-freeze through
the system.
Rupture Disk:
For safety, each machine is equipped with a rupture
disk. In the event the pressure of the water should exceed 8000 PSI, the rupture disk will release pressure
and water on to the ground.
When the disk ruptures, it will need to be replaced.
NOTE: Turn burner switch off. Then open spray
gun to cool heating coil or rupture disk will burst
over time.
Adjustable Thermostat:
The adjustable thermostat can be set between 100°F
to 225°F (37.8° to 108°C). The temperature is dependent on water flow and ambient water temperature.
Cleaning of Coils:
In alkaline water areas, lime deposits can accumulate
rapidly inside the coil pipes. This growth is increased
by the extreme heat build up in the coil. The best
prevention for liming conditions is to use high quality
cleaning detergents. In areas where alkaline water is
an extreme problem, periodic use of Deliming Powder will remove lime and other deposits before coil
becomes plugged.
OPERATOR’S MANUAL
1.Use clean fuel - kerosene, No. 1 home heating
fuel or diesel. Clean or replace fuel filter every
100 hours of operation. Avoid water contaminated
fuel as it will seize up the fuel pump. De-soot coils
monthly. Use an additive if diesel is being used.
2.Check to see that the attached pressure washer
water pump is properly lubricated.
3. Follow winterizing instructions to prevent freeze
damage to pump and coils.
4.Always neutralize and flush detergent from system
after use.
5.If water is known to be high in mineral content, use
a water softener on your water system, or de-scale
as needed.
6.Do not allow acidic, caustic or abrasive fluids to
be pumped through system.
7.Always use high grade quality cleaning products.
8.Never run attached pressure washer pump dry for
extended periods of time.
9.If machine is operated with smoky or eye burning
exhaust, coils will soot up, not letting water reach
maximum operating temperature. (See section on
Maintenance and Service).
10.Never allow water to be sprayed on or near the
motor or burner assembly or any electrical component.
11.Delime coils as per instructions.
It is advisable, periodically, to visually inspect the
burner. Check air inlet to make sure it is not clogged
or blocked. Wipe off any oil spills and keep equipment
clean and dry.
PRESSURE WASHER
PREVENTATIVE MAINTENANCE
Deliming Coils With A Pressure Washer:
Periodic flushing of coils or optional float tank is recommended.
Step 1 Fill a 5 gallon bucket with 4 gallons of water,
then add 1 lb. of deliming powder. Mix thoroughly.
Step 2Remove the high pressure nozzle from the
pressure wand and put the wand into the
bucket. Secure the trigger on the spray gun
in the open position.
Step 3Attach a short section (3-5 ft.) of garden hose
to the attached pressure washer to siphon
solution from the elevated bucket. Start up
pressure washer, allowing solution to be
pumped through pressure washer and into
coils and back into the bucket. Solution should
be allowed to circulate 2-4 hours.
Step 4After circulating solution flush entire system
with fresh water.
Removal of Soot In Heating Coil:
In the heating process fuel residue, in the form of soot
deposits, may develop between the heating coil pipes
and block air flow which affects burner combustion.
When soot has been detected on visual observation,
the soot on the coil must be cleaned off.
13
97-6133 • Rev. 5/07
PRESSURE WASHER
OPERATOR’S MANUAL
MAINTENANCE AND SERVICE
Fuel:
Use clean fuel oil that is not contaminated with water
and debris. Replace fuel filter and drain tank every
100 hours of operation. Use Kerosene No. 1 or No.
2 Heating Fuel (ASTM D306) or diesel only. NEVER
use gasoline in your burner tank. Gasoline is more
combustible than fuel oil and could result in a serious
explosion. NEVER use crankcase or waste oil in your
burner. Fuel machine malfunction could result from
contamination.
supply of fuel to the combustion chamber. Controlling
the flow of fuel in this way gives an instantaneous burn
or no burn situation, thereby eliminating high and low
water temperatures, and combustion smoke normally
associated with machines incorporating a spray gun.
Periodic inspection is recommended to insure that
the fuel solenoid valve functions properly. This can be
done by operating the machine and checking to see
that when the trigger on the spray gun is in the off
position, the burner is not firing.
Fuel Pressure Adjustment:
Ignition Circuit:
Periodically inspect wires, spring contact and electrodes for condition, security and proper spacing.
(CAUTION: 10,000 VOLTS)
To adjust fuel pressure, turn the adjusting screw with
a 5/32” allen wrench (located on the fuel pump) clockwise to increase, counterclockwise to decrease. Do
not exceed 200 PSI.
Electrode Setting:
Field Repair
Instructions
Gap
1/8”
Fuel Pump:
3/16”
Side View
(See illustration below)
Electrodes Check : Periodically check wiring connections.
If necessary to adjust electrodes, use diagram.
Burner Nozzle:
Keep the tip free of surface deposits by wiping it with
a clean, solvent-saturated cloth, being careful not to
plug or enlarge the nozzle. For maximum efficiency,
replace the nozzle each season. Select nozzle size
based on the pressure washer you will be using:
Nozzle
Pressure Washer GPM
1.50
2-3
1.753 - 4
2.00 - 2.25
4-5
All nozzles should be 45° W
Fuel Control System:
The machine utilizes a fuel solenoid valve located on
the fuel pump to control the flow of fuel to the combustion chamber. This solenoid, which is normally
closed, is activated by a flow switch when water is
flowing through it. When an operator releases the
trigger on the spray gun, the flow of water through the
flow switch stops, turning off the current to the fuel
solenoid. The solenoid then closes, shutting off the
1.Remove the screws 10/32” Allen Head from the
machine hood.
2.Remove louvered hood.
3. With a 9/16” wrench, loosen (DO NOT REMOVE)
the two 3/8” x 3/4” HH NC serrated flange bolts
that secure the front panel.
4. With a 2.5 mm hex head wrench (Allen Wrench),
loosen the three set screws that hold the fuel pump
in the blower motor housing located on Idromatic
Boiler Assembly.
5.Carefully remove the fuel pump (Item #53) from
the blower motor, leaving the flexible zinc fuel line
connected, carefully bend the fuel line and fuel
pump away from the blower motor.
6.Locate the fuel pump/fan motor coupling.
7.Inspect the coupling for damage. The inside
diameter of fuel pump coupling requires flat on
one side to engage fuel pump, and the outside
diameter requires two male notches to engage
the blower motor.
8.Perform a check to see if the fuel pump is turning
freely. Use an open end 7mm wrench or small
adjustable wrench on fuel pump shaft.
9.Spin the fuel pump over in both directions using
the wrench for leverage. When the fuel pump is
turning freely (almost to the point you could turn
it by hand) it is ready to reinstall.
10.Align fuel pump coupler on pump shaft/fan motor.
Slide pump into fan motor. Secure pump with the
three set screws.
14
97-6133 • Rev. 5/07
11.Test machine (make sure):
12. When unit is operating properly, turn machine off,
tighten front panel, and install hood and 13 self
tapping screws with recess washers.
OPERATOR’S MANUAL
q Blower motor spins
q Fuel is on
q Machine has power to it
q Switch is on
q Flow of water through machine
q Thermostat is turned up
q Flow switch is adjusted properly
PRESSURE WASHER
Field Repair Instructions
15
97-6133 • Rev. 5/07
PRESSURE WASHER
Exploded View
16
22
46
25
OPERATOR’S MANUAL
31
See
Burner
Assembly
For
Details
12
27
31
33
35
14
39 10
29
28
40
43
41
13
43
4
42
21
29
6
36
45
38
17
11
3
20
9
8
48
24
2
46
26
47
37
44
29
30
23
15
18 34
19
7
1
5
32
16
97-6133 • Rev. 5/07
ITEM PART NO.DESCRIPTIONQTY
ITEM PART NO.DESCRIPTIONQTY
1
90-2020Nut, Cage, 3/8" x 12 Gauge
4
21
11-0110Label, Control Panel
2
90-1996Screw, 3/8" x 3/4" Whiz Loc
4
22
10-02025ALabel, Hot/Caliente, w/Arrows 1
3
4-0303
2
23
10-09004Decal, Discharge
1
4
Wheel & Tire, 6" Steel Rim
1
24
10-09003Decal, Inlet
1
25
11-013Label (HP)
1
26
90-20061Nut, 5/16", Eng
2
6 6-020240Switch, Rocker, Carling w/Green Lens
1
27
90-19710Screw, 1/4" x 3/4" HH, NC
4
7 6-05152Strain Relief, Strt, LQ Tite 3231 Small
1
28
95-07200122 Bracket, Fuel Tank, Left
1
29
90-2018Nut, Cage, 10/32" x 16 Gauge13
6-05181A 8
90-16Screw, 8/32" x 3/4" BHSOC
2
9
90-20041Collar, 5/8" Bore Shaft 3010
95-07102225 ▲ Axle
90-4005
▲ Washer, 5/8"
2
1
2
10
95-07200124 Bracket, Fuel Tank, Right 11
12
▲ Locknut, 1/2"
1
30 4-0204509
Hose, 3/8" x 9', 2 Wire, 3/8" SW
x 3/8" SOL
1
31
90-1991Screw, 10/32" x 1/2" 32
10-08018Label, Warning, Service Cord 1
33
2-01103Grip, 1” Square Handle
1
34
10-08021Label, Disconnect Pwr Supply 1
95-07200125 Frame Assy
1
35
2-0155
Fastener, Ratchet, Black
2
95-07290069 Hood, Cover
1
13
95-07200121Panel, Front
11-1042
▲ Label, Ground
1
1
36
6-05040
6-0505 Block, Terminal, 8 Pole
▲ Bar Jumper
1
2
37
90-100461Screw, 1/4" 1/2" Hex, Black
1
14
95-07102287Strap, Fuel Tank
2
38
90-200490Nut, 8/32", Keps
2
Bumber, Rubber 1" w/Bolt, 5/16" x 1-1/4"
2
39
90-200012Nut, 1/4" Flange
4
40
90-1004
Bolt, 1/4" x 1-1/2"
2
Washer, 1/4" Flat
2
15 2-01015
13
2
16
11-0101Label, Warning, Pictorial
1
41
90-4000
17
95-07200120Panel, Back
1
42
90-19711Screw, 1/4" x 1/2" HH, NC
4
18 2-2007Nipple, 3/8" x 3/8" NPT ST Male
1
43
90-200012Nut, 1/4" Flange
6
44
90-40125
2
19
2-2002Coupler, 3/8" Female, Brass
1
20
2-0031Elbow, 3/8" Street 1
Washer, 3/8" x 1" Steel
OPERATOR’S MANUAL
4-05089Thermostat, Adjustable, 240°F 1
5 6-01062GFCI, 120V 15A, w/36' 12-3 Cord
1
PRESSURE WASHER
Exploded View Parts List
45 2-0103Grommet, Rubber, Nozzle Holder
2
46
9.800-018.0Label, Tipover Hazard
1
47
90-017Nut, 10/32” Keps
4
48
9.800-049.0Label, Cleaning Solution
1
▲ Not Shown
17
97-6133 • Rev. 5/07
PRESSURE WASHER
Burner Assembly Exploded View
9
4
5
3
6
7
OPERATOR’S MANUAL
8
11
42
12
56
13
31
15
59
14
30
10
60
17
38
57
37
40
21
58
22
61
19
20
40
62
23
24
45
25
55
32
26
48
49
41
47
28
43
51
29
27
49
Inlet
46
36
Outlet
39
53
35
50
50
34
54
52
32
33
41
32
33
44
44
18
97-6133 • Rev. 5/07
itempart no.
description
qty
itempart no.
description
qty
91-010170Coil, Lavorwash
1
33
90-2001Nut, 5/16" ESNA
4
2
7-46140112Clamp, Electrode
1
34
2-0036Tee, 1/2" Female, Steel Pipe
1
3
7-46140004Electrode
2
35
2-0046Tee, 1/2", Street
1
4
7-31000017Elbow
1
36
2-0054Elbow, 1/2" JIC x 1/2” Male 1
5
7-30990015Ring, Locking
1
37
4-02100000
Fuel Line, 1/4" Push-on,
6"
6
7-46080002Slide
1
38
70-121603
Hose Barb
2
7
7-46050001
1
39
2-3409Disk, Rupture Assy, 7000 PSI 1
8
7-31040009Nozzle, Burner 1.50, 60°
1
40
2-9040Clamp, Hose, UNI, .46-.54
9
7-56110098Cable, High Tension
2
10
7-34050003
1
41 4-02047714 Hose, 3/8" x 14", 2 Wire,
Pressure Loop
2
11
7-56130147Cover, Tank External, SS
1
42
2-011507Tank, Encore, 5 Gallon Fuel
1
6-021730Switch, Flow, MV60
1
Flange, Burner
Board, Terminal
6
12
7-56100105Deflector
1
43
13
7-56130133Cover, Burner
1
44
90-20040Nut, 3/8" Whiz Loc
4
2-0053Elbow, 1/2" JIC x 3/8", 90°
1
14
7-46040021Coil, High 500
1
45
15
7-56130039
1
46
2-00602Elbow, 1/2" JIC x 1/2" Fem, 90°1
16
7-31000015Connector, 1/8 m
1
47
6-021740Reed, Replacement, MV60
2-0006Nipple, 3/8" x 3/8" Hex, Steel 1
Heater Body
1
17
7-35510013Pump, Fuel
1
48
18
7-34140011Coil, Solenoid
1
49
2-11039Connector, 3/8" Anchor
2
90-19961Screw, 3/8" x 1-3/4" HH, NC
4
1
19
7-30990012Coupling, Plastic
1
50
20
7-33000013Motor, 110V 60 Cycle
1
51
2-1019Elbow, 3/8" Female
4-05088Thermostat, Adjustable, 302°F 1
21
7-30990028
Fan
1
52
22
7-34100004
Box, Electric 70 x 70 x 30
1
53
2-0053Elbow, 1/2" JIC, 3/8", 90°
1
23
7-46080193Refractory
1
54
95-07290082Coil, Mount Plate
1
90-1006
4
2-01167Cap, Fuel Tank, 5 Gallon Fuel 1
24
7-46070006Strip, Coil Fixing
1
55
25
7-46080162Rope, Insulating
1
56
1
57 2-1084
Hose Barb, 1/4" Barb x 1/8" Pipe
1
58
2-99031
Filter, Diesel, Fuel, Disposable 1
59
2-010061Grommet, Fuel Tank
1
60
7-80320
Valve, Fuel Tank Shut-Off
1
61
4-02100000
Fuel Line, 1/4" Push-On, 36"
62
4-02100000
Fuel Line, 1/4" Push-on 26
7-56130026
Base, Heater
27
7-46060013Nut, Coil Fixing
2
28
7-30040015
2
29
7-56090023Guard, Fan
1
30
7-34000017Transformer, 110V 60 Cycle
1
31
7-46160005Tube, Copper
1
32
90-4001
8
Washer, 22 x 39
Washer, 5/16" Flat
Bolt, 5/16" x 3/4"
OPERATOR’S MANUAL
1
PRESSURE WASHER
Burner Assembly Parts List
46"
▲ Not Shown
19
97-6133 • Rev. 5/07
WHAT THIS WARRANTY COVERS
All SHARK PReSSuRe WASHeRS are warranted by SHARK to the original purchaser to be free from defects in materials
and workmanship under normal use, for the periods specified below. This Limited Warranty is subject to the exclusions shown
below, is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced
under this warranty will assume the remainder of the part’s warranty period. This warranty applies to the original purchaser
and is not transferable.
LIMITED LIFETIME PARTS WARRANTY:
Components manufactured by SHARK, such as frames, handles, and belt guards. Forged brass pump manifold. All heating
coils will have a three year warranty. Internal components (excluding oil seals) on the oil-end of all pressure washer pumps
will have a seven year warranty.
ONE YEAR PARTS AND 90 DAYS LAbOR WARRANTY:
All other components, excluding normal wear items as described below, will be warranted for one year on parts. Warranty on
these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty.
WARRANTY PROVIDED bY OTHER MANUFACTURERS:
Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manufacturers’ local authorized service centers. SHARK cannot provide warranty on these items.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover the following items:
1. Normal wear items, such as nozzles, guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings,
packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protectors.
2. Damage or malfunctions resulting from accidents, abuse, modifications, alterations, incorrect installation, improper
servicing, failure to follow manufacturer’s maintenance instructions, or use of the equipment beyond its stated usage
specifications as contained in the operator’s manual.
3. Damage due to freezing, chemical deterioration, scale buildup, rust, corrosion, or thermal expansion.
4. Damage to components from fluctuations in electrical or water supply.
5. Normal maintenance service, including adjustments, fuel system cleaning, and clearing of obstructions.
6. Transportation to service center, shop labor charges, field labor charges, or freight damage.
WHAT YOU MUST DO TO ObTAIN WARRANTY SERVICE
While not required for warranty service, we request that you register your SHARK pressure washer by returning the completed
registration card. In order to obtain warranty service on items, you must return the product to an Authorized SHARK Dealer,
freight prepaid, with proof of purchase, within the applicable warranty period. If the product is permanently installed, you
must notify your Authorized SHARK Dealer of the defect. The Authorized Dealer will file a claim, which must subsequently
verify the defect. In most cases, the part must be returned to SHARK freight prepaid with the claim. For warranty service on
components warranted by other manufacturers, the Authorized Dealer can help you obtain warranty service through these
manufacturers’ local authorized service centers.
LIMITATION OF LIAbILITY
SHARK’S liability for special, incidental, or consequential damages is expressly disclaimed. In no event shall SHARK’S liability
exceed the purchase price of the product in question. SHARK makes every effort to ensure that all illustrations and specifications are correct, however, these do not imply a warranty that the product is merchantable or fit for a particular purpose, or that
the product will actually conform to the illustrations and specifications. THE WARRANTY CONTAINED HEREIN IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representation or promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility
to ensure that the installation and use of SHARK products conforms to local codes. While SHARK attempts to assure that its
products meet national codes, it cannot be responsible for how the customer chooses to use or install the product.
SHARK PReSSuRe WASHeRS
www.shark-pw.com
97-6133 • Rev. 5/07
PRESSURE WASHER WARRANTY
SHARK LIMITED NEW PRODUCT WARRANTY
PRESSURE WASHERS
Form #8.914-336.0 / 97-6133 • Revised 5/07 • Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising