UV410
Owner’s Guide
UV410_26_IB_ENG_120229_5.indd 1
www.sharkclean.com
12-02-29 1:30 PM
This manual covers model numbers:
UV410 26
TECHNICAL SPECIFICATIONS
Voltage: 120V.
Watts: 1200W
Amps: 10A
Hertz: 60Hz
TOLL FREE: 1-800-798-7398
UV410_26_IB_ENG_120229_5.indd 2 12-02-29 1:30 PM
Contents
Thank you for purchasing the Shark
®
Navigator
™
Upright Vacuum.
Important Safety Instructions 2
Getting Started 4
Using the Vacuum 6
Cleaning with the Vacuum Accessories 7
Emptying the Dust Cup Assembly 8
Proper Care of Your Vacuum 9
Troubleshooting 10
Checking for Blockages 11
Maintenance 12
Warranty and Registration 13
UV410_26_IB_ENG_120229_5.indd 1 www.sharkclean.com
1
12-02-29 1:30 PM
IMPORTANT SAFETY INSTRUCTIONS
For Household Use Only
WHEN USING YOUR SHARK
®
NAVIGATOR
™
UPRIGHT VACUUM, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE
FOLLOWED, INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS BEFORE USING
YOUR SHARK
®
NAVIGATOR
™
UPRIGHT
VACUUM.
WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR INJURY:
GENERAL ELECTRICAL SAFETY:
1. Unplug from electrical outlet when not in use and before servicing.
DO NOT use vacuum with a damaged cord or plug.
POLARIZED PLUG:
This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way.
Do not force into the outlet or try to modify the plug to fit.
grasp the plug, not the cord.
5. wet hands.
7. DO NOT close a door on the cord.
WARNING:
TO REDUCE THE RISK OF ELECTRIC
SHOCK OR INJURY DO NOT USE
OUTDOORS OR ON WET SURFACES.
10. Keep power cord away from heated surfaces.
11. Turn off all controls before plugging or unplugging vacuum cleaner.
12. Always turn off this appliance before connecting or disconnecting the motorized nozzle.
HOSE ATTACHMENTS:
13. DO NOT use if air flow is restricted; if the air paths, the hose or the extension tube become blocked, turn the vacuum cleaner off. Remove all obstructions before you turn on the unit again.
14. Keep the end of the hose, wands and other openings away from face and body.
15. Keep rotating brush and suction openings away from hair, face, fingers, uncovered feet or loose clothing.
16. Only use manufacturer’s recommended attachments.
2 TOLL FREE: 1-800-798-7398
UV410_26_IB_ENG_120229_5.indd 2 12-02-29 1:30 PM
GENERAL USE:
17. Use only as described in this manual.
18. DO NOT put any objects into openings.
19. Keep your work area well lit.
20. Keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fibers.
21. DO NOT place vacuum on unstable surfaces such as chairs or tables.
22. DO NOT allow young children to operate the vacuum or use as a toy.
23. DO NOT use vacuum cleaner if it has been dropped, damaged, left outdoors or submerged in water. Return to EURO-PRO Operating LLC for examination, repair or adjustment.
CYCLONIC CHAMBER/DUST CUP/FILTERS:
24. Before turning on the vacuum:
• Make sure that dust cup, cyclonic chamber and all filters are in place after routine maintenance.
• Make sure that all components and filters are thoroughly dry after routine cleaning.
• Only use filters and accessories provided by
EURO-PRO Operating LLC [Failure to do so will void the warranty].
GENERAL CLEANING:
25. DO NOT run the vacuum over large-sized objects.
26. DO NOT pick up hard or sharp objects such as glass, nails, screws or coins that could damage the vacuum cleaner.
27. DO NOT pick up smoking or burning objects such as hot coals, cigarette butts or matches.
28. DO NOT pick up flammable or combustible materials such as lighter fluid, gasoline, kerosene or use in areas where they may be present.
29. DO NOT pick up toxic solutions such as chlorine bleach, ammonia or drain cleaner.
30. DO NOT use in an enclosed space where vapors are present from paint, paint thinner, moth-proofing substances, flammable dust or other explosive or toxic materials.
31. DO NOT vacuum up any liquids.
32. DO NOT immerse vacuum cleaner in water or other liquids.
33. DO NOT use outdoors or on wet surfaces; use only on dry surfaces.
34. Use extra care when cleaning on stairs.
SAVE THESE
INSTRUCTIONS
www.sharkclean.com
3
12-02-29 1:30 PM UV410_26_IB_ENG_120229_5.indd 3
Getting Started
4
A C E
5
F
B
G
3
D 7
2
H
I
FIRST THING’S FIRST, YOU
NEED TO KNOW WHAT’S IN THE
BOX YOU JUST OPENED:
A Vacuum Body
B Floor Power Nozzle
C Handle Assembly
D Super Stretch Hose
E Cleaning Wand
F Pet Hair Power Brush
G Cleaning Attachments
H 24” Crevice Tool
I Extended Reach Kit
Your Shark ® Navigator ™
Upright is easy to assemble:
1 Lay your vacuum body on a level surface.
2 Slide the electrical connection from the power nozzle into the main body to click into place.
3 Connect the hose from the main body to the power nozzle; push with a slight turning motion to create a snug fit.
4 Slide the handle assembly into the upright unit aligning the hose hook on the handle assembly with the power cord hooks on the back of the unit.
5 Secure the handle assembly in place with included nut/bolt
(shipped attached to handle assembly).
6 Place the vacuum in the upright position.
7 Store the Crevice Tool, Dusting
Brush and Cleaning Wand on the unit.
* Note: Optional tools are available for sale for any UV410 model: 1-800-798-7398.
4 TOLL FREE: 1-800-798-7398
UV410_26_IB_ENG_120229_5.indd 4 12-02-29 1:30 PM
b a
8 c d
9
8 Attach the Super Stretch Hose: a) Snap hose into swivel connector b) Route under anti-tip hook c) Route over upper hose holder d) Press securely onto cleaning wand
IMPORTANT:
To prevent vacuum from tipping, secure hose under the anti-tip hose hook.
9 To store the vacuum:
When storing your vacuum, wind the cord around the two cord holders and secure with cord clip:
• Quick Cord release at the top of the unit – place in the upright position.
• Cord holder near the base – turn it until it is pointing down.
To release the cord, turn the Quick
Cord release to the left or right.
Store the Extended Reach Kit, the Pet Hair Power Brush and the 24" Crevice Tool with the vacuum when not in use.
IMPORTANT:
For suction to reach the Floor
Power Nozzle, the Cleaning
Wand and Super Stretch Hose must be attached securely on the vacuum body.
10 To carry the vacuum:
With the unit in the standing position, lift by the Dust Cup
Handle.
CAUTION: When lifting or carrying, DO NOT press Dust
Cup Assembly release button.
www.sharkclean.com
5
UV410_26_IB_ENG_120229_5.indd 5 12-02-29 1:30 PM
Using the Vacuum
IMPORTANT: To protect your carpets, the brushroll will only turn on when you have pulled the handle back towards you and released the Floor Power Nozzle.
Power Switch Settings
OFF
Bare Floors /
Tools
Carpets
Suction Release
Release suction for easier push and pull on high pile carpets and area rugs.
Your Shark ® Navigator ™
1
3
6
Upright
Vacuum can be used to clean bare floors or carpets – with the click of a switch.
Stand the vacuum into the upright position.
Plug in the vacuum.
Start with the Power Switch in the “O" - Off position.
2 Place your foot on the Floor
Power Nozzle and pull handle towards you.
Set the Power Switch to desired cleaning setting.
4 When cleaning carpets:
Ensure you have pulled the handle towards you and select the “II" - Brushroll On position to agitate the carpet fibers for deeper cleaning performance.
When cleaning bare floors:
Select the "I" - On position for suction only cleaning to avoid scattering dirt while cleaning.
5 Due to the huge suction power of this vacuum, it may become necessary to adjust the suction release on the hose. If the vacuum is difficult to push or pull or if it is lifting up area rugs, adjust the suction release by opening or closing the valve
at the top end of the hose.
TOLL FREE: 1-800-798-7398
IMPORTANT:
Your Brushroll Indicator Light will illuminate solid green when the brushroll is on, or solid red if there is a blockage. This feature is designed to protect your
Lifetime Belt that powers your brushroll. See Checking for
Blockages on page 11.
NOTE: The height of your power nozzle has been optimized for easy pushing and superior cleaning on all floor types, so there is no need to make any height adjustments as you transition to different floor & carpet types.
UV410_26_IB_ENG_120229_5.indd 6 12-02-29 1:30 PM
Cleaning with the Vacuum Accessories
1
3
4 5 6
2
Extended Reach
Cleaning Kit
Before cleaning with your accessories:
Stand vacuum into upright position.
Secure Super
Stretch Hose in the anti-tip hose hook to prevent tipping.
Select the “I" - On position for suction only cleaning.
DO NOT pull vacuum cleaner around by the hose.
DO NOT overextend the hose.
4 5 6
3
Vacuum Accessories
Your vacuum comes with a Super
Stretch Hose and Cleaning Wand.
Use one or the other to attach your cleaning accessories.
1 Using the Super Stretch Hose:
Stand the vacuum into upright position.
Remove the hose from the
Cleaning Wand.
Push the selected tool into the hose connector.
2 Using the Cleaning Wand:
Stand the vacuum into upright position.
Remove the Cleaning Wand
(with hose attached) from the unit.
Push the selected tool into the end of the Cleaning Wand.
3 Pet Hair Power Brush
4 Dusting Brush
5 Crevice Tool
6 24” Crevice Tool
Extended Reach Cleaning Kit
Includes an extra Cleaning Wand and extra Super Stretch Hose.
Increases your cleaning reach to over 27 feet!
To order additional parts and accessories, go to www.sharkclean.com or call
1-800-798-7398.
www.sharkclean.com
7
UV410_26_IB_ENG_120229_5.indd 7 12-02-29 1:30 PM
Emptying the Dust Cup Assembly
For best results empty the Dust Cup after each use; empty several times during prolonged usage. or when it reaches the MAX fill line.
NEVER OVER-FILL THE DUST
CUP.
Stand vacuum into upright position.
Turn vacuum off.
1 2 3
CAUTION:
Unplug the vacuum; failure to do so might result in electric shock.
To empty the Dust Cup:
1 Grip carry handle and press the Dust Cup release button to remove.
2 Option A: For Quick Empty:
Insert Dust Cup deep inside trash receptacle to contain dust and debris.
Press the bottom Dust Cup release button; tap container gently to dislodge and release dust and debris.
Snap door in place.
Important: If the Dust Cup
Door does not swing open after pressing the release button, push the door open using the bottom door tabs.
8 TOLL FREE: 1-800-798-7398
3 Option B: For Allergy Sufferers:
Wrap a trash bag around the
Dust Cup leaving space at the bottom for the door to swing open.
Locate the Dust Cup Door release button within the trash bag and press to release as you shake the dust cup to empty dust and debris.
Snap the bottom door in place.
Note: Option B can also be performed outside of the home to further minimize releasing dust back into the air. Carry just the Dust Cup and trash bag outside.
Note: Some dust and debris may remain in the top of your dust cup on or near the metal screen. It is not necessary to completely remove this material before continuing to vacuum;
Shark ® advanced cyclonic action will sweep the metal screen clean once you begin to refill your dust cup.
UV410_26_IB_ENG_120229_5.indd 8 12-02-29 1:30 PM
1
2
Proper Care of Your Vacuum
COMPONENT MAINTENANCE SCHEDULE
Dust Cup Empty each time you vacuum.
Pre-Motor Foam Filter Rinse and air dry every 3 months under normal use.
3
4
Pre-Motor Felt Filter
Post-Motor Filter
Rinse and air dry every 3 months under normal use.
Clean once every 12 months under normal use.
NOTE: The material in the filters will discolor over time. This is NORMAL and will not affect the performance of the filters.
DO NOT operate the vacuum without ALL the filters in place.
DO NOT operate the vacuum with WET filters.
Pre-Motor
Foam Filter
Pre-Motor
Felt Filter
(Felt Side Up)
Filter Frame Filter Frame
(Underside)
IMPORTANT: Loss of Suction may
occur if filters are not cleaned every 3 months. Rinse and allow to air dry completely.
Tap loose dirt from foam filter as needed in between washing. Filters may appear dirty after use - this is normal.
Post Motor
Filter
To clean the pre-motor filters:
1 Remove the dust cup.
Lift the filter frame out from the top of the motor base.
Remove the foam filter from inside the filter frame.
Turn the filter frame upside down and carefully pull the felt filter out
Rinse the filters thoroughly in lukewarm water until the water runs clear as per the maintenance schedule above.
DO NOT put the filters in the washing machine or dishwasher.
Squeeze out excess water and let air-dry for at least 24 hours before replacing. Do not use a hair dryer or other heating methods to dry. replacing the felt filter, make sure that the felt part of the filter is facing out.
Replace the filter frame into the motor base and then replace the dust cup.
To clean the post-motor filter:
Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum.
2 Take out the filter by pulling it straight out.
Wash the filter under the tap using lukewarm water with the dirty side face down until the water runs clear.
DO NOT put the filter in the washing machine or dishwasher.
4 Allow the filter to air dry for 24 hours. Do not use a hair dryer or other heating methods to dry.
Once the filter is dry, replace it back into the vacuum.
6 Replace the cover by inserting the two tabs into the holes at the bottom and then swinging the cover up until it clicks into place.
www.sharkclean.com
9
11
UV410_26_IB_ENG_120229_5.indd 9 12-02-29 1:30 PM
Troubleshooting
WARNING:
To reduce the risk of electric shock, the power cord must be disconnected before performing maintenance/troubleshooting checks.
PROBLEM
Vacuum is not picking up dirt.
Vacuum lifts scatter rugs
(lightweight, movable rugs).
Airflow is restricted. No suction or light suction.
Motorized floor brush has become jammed or has shut off.
Vacuum turns off on its own.
POSSIBLE REASONS & SOLUTIONS
Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See
“Maintenance” sections for instructions.)
Dust cup may be full; empty dust cup.
Check hose and hose connections for blockages; clear blockages if required.
If dust cup is empty, and attachment inlets are clear, check for other blockages. (See “Checking for Blockages” for instructions.)
Suction is powerful. Take care when vacuuming scatter-type rugs or rugs with delicately sewn edges. Open the suction release on the hose to decrease suction power.
Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See
“Maintenance” sections for instructions.)
Dust cup may be full; empty dust cup.
Check hose, hose connections, nozzles and accessories for blockages; clear blockages if required.
Close the suction release on the hose to increase suction power.
If dust cup is empty, and attachment inlets are clear, check for other blockages. (See “Checking for Blockages” for instructions.)
Immediately turn off and unplug vacuum, disconnect the nozzle and remove blockage before reconnecting and turning vacuum back on. (See “Checking for Blockages” for instructions.)
This vacuum cleaner is equipped with a motor protective thermostat. If for some reason your vacuum overheats, the thermostat will automatically turn the unit off. Should this occur, perform the following steps to restart the motor thermostat:
1. Move the On/Off switch to the “O” (Off) position.
2. Unplug the vacuum.
3. Empty the dust cup and clean filters. (See “Maintenance” sections for instructions.)
4. Check for blockages in hose, accessories and inlet openings. (See
“Checking for Blockages” for instructions.)
5. Allow the unit to cool for a minimum of 45 minutes.
6. Plug in the vacuum.
7. Turn the On/Off switch to the “I” (On) position to restart the vacuum.
Note: If vacuum still does not start, contact Customer Service at:
1-800-798-7398.
10 TOLL FREE: 1-800-798-7398
UV410_26_IB_ENG_120229_5.indd 10 12-02-29 1:30 PM
Checking for Blockages
Blockages may cause your vacuum to overheat and shut down. If so, clear the blockages, then follow the instructions for Resetting the
Motor Thermostat on page 12.
WARNING: Never insert sharp objects into any opening to clear an obstruction.
IMPORTANT: Damages caused while clearing or attempting to clear blockages are not covered under your product’s limited warranty.
Unplug the vacuum before checking for blockages.
Reassemble all parts securely before operating vacuum.
2
1
1
2
3
4
3
1 Dust Cup Air Duct:
Stand vacuum into upright position.
Remove Dust Cup Assembly and empty Dust Cup if necessary.
Disconnect the Super Stretch
Hose.
Check Air Duct behind Dust Cup for clogs; clear before replacing
Dust Cup Assembly.
2 Intake Opening behind the
Brushroll:
Lay the vacuum flat to expose brushroll.
Check opening behind the brushroll for clogs.
Clear the opening.
Clear the brushroll; use scissors to carefully cut away threads, hair or other debris that might be trapped in the bristles.
3 Floor Power Nozzle Hose
Connector:
Lay vacuum flat.
Remove Nozzle Hose and check for clogs.
Push the Hose Connector back onto the Floor Power Nozzle.
4 Hose:
Stand vacuum upright.
Remove hose from both the unit and Cleaning Wand ends.
Inspect both ends and the length of the hose for clogs.
Return the hose to the unit www.sharkclean.com
11
UV410_26_IB_ENG_120229_5.indd 11 12-02-29 1:30 PM
Maintenance
Resetting the Motor Thermostat
Your Shark ® Navigator ™ Upright
Vacuum is equipped with a protective Motor Thermostat. If the motor should overheat, the thermostat shuts off the power.
A
1 Cleaning the Pet Hair Power
Brush -
Slide locking latch ( A ) forward.
Gently tilt brush housing upward to open.
IMPORTANT: DO NOT force; it will not open all the way.
Remove debris from turbine wheel and air passage.
To reset the Motor Thermostat:
Move the Power Button to the
“O” – Off position.
Unplug the vacuum.
Check for clogged hose or filter; unclog hose and replace filter.
Refer to Checking for Blockages on page 11.
Ordering Replacement Parts
To order additional parts and accessories, go to
www.sharkclean.com or call 1-800-798-7398.
PART NO.
1114-FC
Wait 45 minutes for vacuum to cool; then plug in the vacuum.
Turn the Power Switch to the
“I” – On position to start the vacuum.
Note: If vacuum still does not start, contact Customer Service at:
1-800-798-7398.
PART
Super Stretch Hose
Dusting Brush &
Crevice Tool
Foam & Felt Filters
Turbo Brush
Cleaning Wand
24"Crevice Tool
1115-FC
XFF36
137FFJ
1116-FC
1124-FC
12 TOLL FREE: 1-800-798-7398
UV410_26_IB_ENG_120229_5.indd 12 12-02-29 1:30 PM
Euro-Pro Five-Year (5) Limited Warranty
EURO-PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of five (5) years from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid to:
• U.S.: EURO-PRO Operating LLC
For customer service support call 1-800-798-7398 or visit www.sharkclean.com
• Canada: EURO-PRO Operating LLC
4400 Bois Franc, St. Laurent, Québec H4S 1A7
If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase date and $16.99 to cover the cost of return shipping and handling must be included.*
Non-durable parts including, without limitation, filters, brushes and electrical parts which normally require replacement are specifically excluded from warranty.
The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.
Product Registration
Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark ® product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.
The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions. www.sharkclean.com
13
UV410_26_IB_ENG_120229_5.indd 13 12-02-29 1:30 PM
Euro-Pro Operating LLC
USA: Newton, MA 02459
CAN: 4400 Bois Franc, St-Laurent, QC H4S 1A7
English: 1-800-798-7398 www.sharkclean.com
Copyright © Euro-Pro Operating LLC 2012
Printed in China
Illustrations may differ from actual product.
UV410.E.120229.5
UV410_26_IB_ENG_120229_5.indd 14 12-02-29 1:30 PM
