FRANÇAIS
OPERATION MANUAL
MODE D'EMPLOI
MANUAL DE OPERACIÓN
ENGLISH
LC-32HT3U
LC-37HT3U
LC-42HT3U
LIQUID CRYSTAL TELEVISION
TÉLÉVISEUR ACL
TELEVISOR CON PANTALLA
DE CRISTAL LÍQUIDO
ESPAÑOL
LC-32HT3U
LC-37HT3U
LC-42HT3U
IMPORTANT : Please read this operation manual before starting operating the equipment.
IMPORTANTE : Lea este manual de operación antes de comenzar a operar el equipo.
ENGLISH
LC-32HT3U
LC-37HT3U
LC-42HT3U
LIQUID CRYSTAL TELEVISION
ENGLISH
OPERATION MANUAL
• These TV (LC-32HT3U, LC-37HT3U, LC-42HT3U models)
are designed for hotel guest rooms. Each has two
modes, PPV TV mode and Normal mode, and the factory
preset is PPV TV mode.
• The TV is equipped with LODGENET, ONCOMMAND,
NXTV, nSTREAMS and SeaChange Pay Per View
interface.
• The examples used throughout this manual are based on the
LC-37HT3U model.
IMPORTANT:
To aid reporting in case of loss or theft, please record the
TV's model and serial numbers in the space provided. The
numbers are located at the rear of the TV.
Model No.:
Serial No.:
IMPORTANT INFORMATION
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION:
The lightning flash with arrow-head
symbol, within an equilateral triangle,
is intended to alert the user to the
presence of uninsulated “dangerous
voltage” within the product's
enclosure that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
The exclamation point within a
triangle is intended to alert the user
to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the product.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
1
IMPORTANT INFORMATION
CAUTION:
DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND, TRIPOD, BRACKET, OR TABLE.
THE PRODUCT MAY FALL CAUSING SERIOUS PERSONAL INJURY AND SERIOUS DAMAGE TO
THE PRODUCT. USE ONLY WITH A CART, STAND, TRIPOD, BRACKET, OR TABLE RECOMMENDED
BY THE MANUFACTURER OR SOLD WITH THE PRODUCT. FOLLOW THE MANUFACTURER'S
INSTRUCTIONS WHEN INSTALLING THE PRODUCT AND USE MOUNTING ACCESSORIES
RECOMMENDED BY THE MANUFACTURER. A PRODUCT AND CART COMBINATION SHOULD BE
MOVED WITH CARE. QUICK STOPS, EXCESSIVE FORCE, AND UNEVEN SURFACES MAY CAUSE
THE PRODUCT AND CART COMBINATION TO OVERTURN.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly
approved by the manufacturer could void the user's authority to operate this equipment.
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded
cables and connectors for connections.
DECLARATION OF CONFORMITY:
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-32HT3U/LC-37HT3U/LC-42HT3U
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RESPONSIBLE PARTY:
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TEL: 1-800-BE-SHARP
For Business Customers: URL http://www.sharpusa.com
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
“Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the National
Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical.”
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental
considerations. For disposal or recycling information, please contact your local
authorities, the Electronic Industries Alliance: www.eiae.org, the lamp recycling
organization: www.lamprecycle.org or Sharp at 1-800-BE-SHARP (For U.S.A. Only)
Trademarks
• Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories.
• “HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI
Licensing LLC.”
• Pro:Idiom™ is a trademark of Zenith Electronics Corporation.
2
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years
of trouble-free operation of your product, please read the Important Safety Instructions carefully before
using this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please
observe the following instructions when installing, operating and cleaning the product. To ensure your safety
and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully
before using the product.
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,
consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Information
15) Power Sources—This product should be operated only from the type of power source indicated on the
marking label. If you are not sure of the type of power supply to your home, consult your product dealer or
local power company. For products intended to operate from battery power, or other sources, refer to the
operating instructions.
16) Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this
can result in a risk of fire or electric shock.
17) Object and Liquid Entry—Never push objects of any kind into this product through openings as they may
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
18) Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require extensive work by a qualified technician
to restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this indicates a need for service.
19) Replacement Parts—When replacement parts are required, be sure the service technician has used
replacement parts specified by the manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
20) Safety Check—Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
21) Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product
according to the method recommended by the manufacturer.
3
IMPORTANT SAFETY INSTRUCTIONS
• Water and Moisture — Do not use this product near water - for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.
• Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the
product on an unstable base can cause the product to fall, resulting in serious personal injuries
as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended
by the manufacturer or sold with the product. When mounting the product on a wall, be sure to
follow the manufacturer's instructions. Use only the mounting hardware recommended by the
manufacturer.
• Selecting the location — Select a place with no direct sunlight and good ventilation.
• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not
cover or block these vents and openings since insufficient ventilation can cause overheating
and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other
similar surface, since they can block ventilation openings. This product is not designed for builtin installation; do not place the product in an enclosed place such as a bookcase or rack, unless
proper ventilation is provided or the manufacturer's instructions are followed.
• The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the
product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in
case the panel breaks.
• Heat — The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
• The Liquid Crystal panel is a very high technology product with 3,147,264 thin film transistors, giving you fine picture details.
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this
does not affect the performance of your product.
Precautions when transporting the TV
• Be sure to always carry the TV by two people holding it with two hands — one hand on
each side of the TV.
• Lightning — For added protection for this television equipment during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug it from the wall outlet
and disconnect the antenna. This will prevent damage to the equipment due to lightning and
power-line surges.
• Power Lines — An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them might be fatal.
4
IMPORTANT SAFETY INSTRUCTIONS
• Outdoor Antenna Grounding — If an outside antenna is connected to the television equipment, be sure the antenna
system is grounded so as to provide some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC — NATIONAL ELECTRICAL CODE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE
SYSTEM
(NEC ART 250, PART H)
• To prevent fire, never place any type of candle or flames on the top or near the TV set.
• To prevent fire or shock hazard, do not expose this product to dripping or splashing.
No objects filled with liquids, such as vases, should be placed on the product.
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy
items.
• Turn off the main power and unplug the AC cord from the wall outlet before handling.
• Use a soft cloth and gently wipe the surface of the display panel. Using a hard cloth may
scratch the panel surface.
• Use a soft damp cloth to gently wipe the panel when it is really dirty.
(It may scratch the panel surface when wiped strongly.)
• If the panel is dusty, use an anti-static brush, which is commercially available, to clean it.
• To protect the panel, do not use a dirty cloth, liquid cleaners or chemical cloth to clean it,
such materials may damage the panel surface.
• To clean the outer cabinet, use the same method. Do not use liquid or aerosol cleaners.
• Do not display a still picture for a long time, as this could cause an afterimage to remain.
5
General notes
The Remote Replicator and the remote control unit are not supplied with this product.
The Remote Replicator (model number: AN-H06RCU) and the remote control unit (model number: AN-32HTRC)
are available as optional accessories. Contact your nearest Sharp dealer for purchase.
See the OPERATION MANUAL FOR HOTEL OPERATOR for details on the TV settings.
Remote Replicator
(AN-H06RCU)
Remote control unit
(AN-32HTRC)
For hotel guests, use the remote control unit supplied by the Pay Per View provider to
operate the TV.
6
Contents
Introduction
IMPORTANT INFORMATION....................................................................................... 1
Trademarks .................................................................................................................. 2
DEAR SHARP CUSTOMER.......................................................................................... 3
IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 3
General notes ............................................................................................................... 6
Contents ....................................................................................................................... 7
Supplied accessories .................................................................................................. 8
Optional accessories ................................................................................................... 8
Part names ................................................................................................................... 9
TV (Top/Front) .................................................................................................. 9
TV (Rear) (LC-32HT3U/37HT3U) .................................................................... 10
TV (Rear) (LC-42HT3U)................................................................................... 11
Remote control unit (Optional accessory:
AN-32HTRC) .............................................................................................. 12
Remote Replicator (Optional accessory:
AN-H06RCU) ............................................................................................. 13
Preparation
Attaching the stand (LC-32HT3U/37HT3U) ................................................... 14
Attaching the stand (LC-42HT3U) .................................................................. 15
Setting the TV................................................................................................. 16
Connecting to the PPV terminal box .............................................................. 16
Antennas ........................................................................................................ 17
Turning on the power ..................................................................................... 18
Turning off the power ..................................................................................... 18
Appendix
Removing the stand ....................................................................................... 19
Setting the TV on the wall .............................................................................. 19
Troubleshooting ............................................................................................. 20
Troubleshooting-Digital broadcasting ............................................................ 20
Specifications ................................................................................................. 21
Optional accessory ........................................................................................ 21
Information on the software license
for this product .......................................................................................... 22
Calling for Service...................................................................................................... 23
LIMITED WARRANTY ................................................................................................ 23
Dimensional drawings
• The dimensional drawings for the LCD TV set are shown on the inside back cover.
7
Supplied accessories
Make sure the following accessories are provided with the product.
LC-32HT3U/LC-37HT3U
AC cord
(g1)
Page 16
Cable Clamp (g1)
Cable tie (g1)
Page 16
Stand unit
(g1)
Page 14
Operation manual
(g1)
AC cord
(g1)
Page 16
Cable Clamp (g2)
Cable tie (g1)
Page 16
Stand unit
(g1)
Page 15
Operation manual
(g1)
LC-42HT3U
NOTE
• Always use the AC cord supplied with the TV.
Optional accessories
8
Remote Replicator with an RJ-11 cable
Remote control unit
AN-H06RCU
AN-32HTRC
Part names
TV (Top/Front)
Channel buttons (CHs/r)
Volume buttons (VOLl/k)
INPUT button
OPC indicator**
Remote control sensor
OPC sensor*
POWER button
SLEEP indicator**
POWER indicator**
NOTE
* OPC: Optical Picture Control (See OPERATION MANUAL FOR HOTEL OPERATOR.)
** See page 18 for TV status indicator.
9
Part names
TV (Rear)
LC-32HT3U/LC-37HT3U
HDMI terminal (INPUT 4)
HDMI terminal (INPUT 5)
PC IN terminal (INPUT 6)
Antenna/Cable in
AUDIO input terminals (INPUT 5)
DIGITAL AUDIO OUTPUT terminal
TRANSPORT terminal*
INPUT 3 terminals
INPUT 2 terminals
INPUT 1 terminals
AC INPUT terminal
AUDIO OUTPUT
terminals
NOTE
* The TRANSPORT terminal is designed for hotel communication. Do not use it for other purposes.
10
Part names
TV (Rear)
LC-42HT3U
HDMI terminal (INPUT 4)
HDMI terminal (INPUT 5)
PC IN terminal (INPUT 6)
Antenna/Cable in
AUDIO input terminals
(INPUT 5)
DIGITAL AUDIO OUTPUT
terminal
TRANSPORT terminal*
INPUT 3 terminals
INPUT 1 terminals
AC INPUT terminal
AUDIO OUTPUT terminals
INPUT 2 terminals
NOTE
* The TRANSPORT terminal is designed for hotel communication. Do not use it for other purposes.
11
Part names
Remote control unit
(Optional accessory: AN-32HTRC)
1
14
1
2
3
4
5
6
7
2
3
15
8
9
10
4
16
11
12
13
14
5
6
17
7
18
8
19
9
20
16
17
10
21
18
22
19
20
21
22
11
23
24
25
15
23
24
26
12
13
27
25
26
27
TV POWER: Switches the TV power on or enters
standby.
DISPLAY: Displays the channel information.
SOURCE POWER: Turns the power of the external
equipment on and off.
External equipment operational buttons: Operates
the external equipment.
0 – 9: Sets the channel.
• (DOT)
INPUT: Selects a TV input source. (TV, INPUT 1, INPUT 2,
INPUT 3, INPUT 4, INPUT 5, INPUT 6)
VOL k/l: Sets the volume.
SURROUND: Selects Surround settings.
FREEZE: Sets the still image. Press again to return to
normal screen.
EXIT: Turns off the menu screen.
SLEEP: Sets the sleep timer.
AUDIO: Selects the MTS/SAP or the audio mode during
multi-channel audio broadcasts.
FUNCTION: Switches the remote control for TV, CBL/
SAT, VCR, DVD and AUDIO operation. Indicator lights up
for the current mode.
* To enter the code registration mode, you need to press
FUNCTION and DISPLAY at the same time.
LIGHT D: When pressed all buttons on the remote
control unit will light. The lighting will turn off if no
operations are performed within about 5 seconds. This
button is used for performing operations in low-light
situations.
VIEW MODE: Selects the screen size.
ENT: Jumps to a channel after selecting with the 0–9
buttons.
FLASHBACK: Returns to the previous channel or
external input mode.
CHr/s: Selects the channel.
MUTE: Mutes the sound.
MENU: Displays the menu screen.
a/b/c/d/ENTER: Selects a desired item on the
screen.
RETURN: Returns to the previous menu screen.
FAVORITE CH
A, B, C, D: Selects four preset favorite channels in four
different categories.
While watching, you can toggle the selected channels by
pressing A, B, C and D.
FAVORITE: Set the favorite channels.
CC: Displays captions from a closed-caption source.
AV MODE: Selects an audio or video setting.
(When the input source is TV, INPUT 1, 2 or 3:
STANDARD, MOVIE, GAME, USER, DYNAMIC (Fixed),
DYNAMIC. When the input source is INPUT 4, 5 or 6:
STANDARD, MOVIE, GAME, PC, USER, DYNAMIC
(Fixed), DYNAMIC)
NOTE
• When using the remote control unit, point it at the TV.
• See the OPERATION MANUAL FOR HOTEL
OPERATOR for details on the functions of each button.
12
Part names
Remote Replicator
(Optional accessory: AN-H06RCU)
1
2
5
6
7
8
9
10
3
4
11
LEARN indicator: Lights up while storing the TV
settings from the TV to the Remote Replicator.
2 DONE indicator: Lights up when storing or
transferring is finished.
3 TEACH indicator: Lights up while transferring the
TV settings from the Remote Replicator to the TV.
4 MEMORY SELECT indicator: Indicates which
memory bank is selected.
5 LEARN button: Store the TV settings from the TV
to the Remote Replicator.
6 TEACH button: Transfer the TV settings from the
Remote Replicator to the TV.
7 ROOM button: The TV turns off and enters the
ROOM mode when the TV is in the MASTER mode.
You can turn on or off the TV when the TV is in the
ROOM mode.
8 MASTER button: The TV is turned on and enters
the MASTER mode when the TV is turned off. The
menu screen displays when the TV is turned on in
the MASTER mode or the ROOM mode. The TV is
turned off and enters the PPV TV mode when the
TV is in the Normal TV mode.
9 DIAGNOSTICS button: Perform operational tests.
10 MEMORY SELECT button: Select the memory
bank to store or transfer data.
11 TRANSPORT (RJ-11) connector: Connect to the
TV when storing or transferring the data.
1
NOTE
• When using the Remote Replicator, point it at the TV.
• See the OPERATION MANUAL FOR HOTEL OPERATOR
for details on the functions of each button.
• The TRANSPORT (RJ-11) connector is designed for hotel
communication. Do not use it for other purposes.
The Remote Replicator is only for hotel operators.
13
Preparation
Attaching the stand
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
LC-32HT3U/37HT3U
1
Confirm that there are 9 screws (all the same
size) supplied with the TV.
2
1 Set the post for the stand unit onto the
box.
2 Attach the base to the post.
3 Insert and tighten the 5 screws into the 5
holes on the bottom of the base.
3
1 Insert the stand into the openings on the
bottom of the TV.
2 Insert and tighten the 4 screws into the 4
holes on the rear of the TV.
Hex key
Screw
Soft cushion
Hex key
Screw
NOTE
• To detach the stand, perform the steps in reverse order.
14
Preparation
Attaching the stand
• Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT terminal.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
CAUTION
• Attach the stand in the correct direction.
• Be sure to follow the instructions. Incorrect installation of the stand may result in the TV falling over.
LC-42HT3U
1
Confirm that there are 8 screws supplied with
the TV.
Short screws (g4)
(Used in step 2)
Long screws (g4)
(Used in step 3)
3
1 Insert the stand into the openings on the
bottom of the TV.
2 Insert and tighten the 4 long screws into
the 4 holes on the rear of the TV.
Hex key
2
1 Set the post for the stand unit onto the
box.
2 Attach the base to the post.
3 Insert and tighten the 4 short screws into
the 4 holes on the bottom of the base.
Long screw
Soft cushion
Hex key
Short screw
NOTE
• To detach the stand, perform the steps in reverse order.
15
Preparation
Setting the TV
1
Attach your antenna to the back of the TV.
(See page 17.)
2
Connect the AC plug for the TV into the AC
outlet.
3
Place the ferrite core in the space indicated
in the below figure and bundle the cords
properly with a cable clamp and cable tie.
LC-32HT3U/37HT3U
• Place the TV close to the AC outlet, and keep
the power plug within reach.
AC outlet
LC-42HT3U
AC cord
CAUTION
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT
TOUCH UN-INSULATED PARTS OF ANY CABLES
WITH THE AC CORD CONNECTED.
NOTE
• Speakers cannot be detached from the TV.
• TV angle cannot be adjusted.
Connecting to the PPV terminal box
Connect the TV and the PPV terminal box as shown.
RJ-11 cable
(Supplied by Pay Per View
provider)
To power outlet
To room antenna terminal
Coaxial cable
(Commercially available)
16
PPV terminal box
Hotel server
Preparation
Antennas
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,
plug it into the antenna terminal at the rear of the TV set.
1. A 75-ohm system is generally a round cable with F-type
connector that can easily be attached to a terminal
without tools (Commercially available).
NOTICE
F-type connector should be fingertightened only.
When connecting the RF cable to the TV set, do not
tighten F-type connector with tools.
If tools are used, it may cause damage to your TV
set. (The breaking of internal circuit, etc.)
F-type connector
75-ohm coaxial cable (round)
2. A 300-ohm system is a flat “twin-lead” cable that can be
attached to a 75-ohm terminal through a 300/75-ohm
adapter (Commercially available).
F-type connector
75-ohm coaxial cable
300-ohm twin-lead cable (flat)
Connecting Antenna Cable
1 Cable without a
CATV converter
Home Antenna
terminal (75-ohm)
Cable TV lead-In
Coaxial cable
(commercially available)
2 VHF/UHF antenna
Home Antenna
terminal (75-ohm)
75-ohm coaxial cable (round)
Coaxial cable
(commercially available)
• Connect the antenna cable
to the TV using one of the
methods in the illustration
as shown (1, 2, 3 or 4).
3 Combination VHF/
UHF antenna
or 75-ohm coaxial cable (round)
300-ohm twin-lead cable (flat)
300/75-ohm adapter
(commercially available)
VHF
UHF
ANTENNA ANTENNA
4 Separate VHF/UHF
antenna
300-ohm
twin-lead cable
300-ohm twin-lead cable
Combiner
(commercially
available)
IN
or
75-ohm coaxial cable
OUT
To TV antenna
terminal
17
Preparation
Simple operations for watching a TV program
Turning on the power
Press POWER on the TV.
• POWER indicator (Green): The TV is on. (After a few
seconds, a window appears with sound.)
Turning off the power
POWER
Press POWER on the TV.
• The TV enters standby and the image on the screen
disappears.
• The POWER indicator on the TV turns off.
NOTE
• If you are not going to use this TV for a long period of time,
be sure to remove the AC cord from the power outlet.
• Weak electric power is still consumed even when the TV is
turned off.
POWER indicator
OPC indicator
SLEEP indicator
TV status indicator (POWER)
ON
Lighting (Green)
Standby
Lights off
TV status indicator (OPC)
“Off” is selected in OPC setting
Lights off
“On” or “On: Display” is selected in OPC setting
Lighting (Green)
*OPC: Optical Picture Control
TV status indicator (SLEEP)
“Off” is selected in SLEEP setting
Lights off
“30”, “60”, “90” or “120” is selected in SLEEP setting
Lighting (Red)
IMPORTANT:
IF THE UNIT DOES NOT POWER ON - UNPLUG THE AQUOS TELEVISION FROM THE OUTLET AND REPEAT
THE INSTALLATION STEPS.
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT US AT 1-800-BE-SHARP.
For hotel guests, use the remote control unit supplied by the Pay Per View
provider to operate the TV.
18
Appendix
Removing the stand
Before detaching (or attaching) stand, unplug the AC cord from the AC INPUT terminal.
CAUTION
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
Before attaching/detaching stand
• Before performing work make sure to turn off the TV.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
1
2
Hex key
Unfasten the four screws used to secure the stand in
place.
Detach the stand from the TV. (Hold the stand so it
will not drop from the edge of the base area.)
NOTE
• To attach the stand, perform the above steps in reverse order.
Setting the TV on the wall
CAUTION
• The model AN-52AG1 of the wall mount bracket can be used only with LC-42HT3U.
• This TV should be mounted on the wall only with the AN-37AG2/AN-52AG1 (SHARP) wall mount bracket. The use
of other wall mount brackets may result in an unstable installation and may cause serious injuries.
• Installing the TV requires special skill that should only be performed by qualified service personnel. Customers should not attempt to
do the work themselves. SHARP bears no responsibility for improper mounting or mounting that results in accident or injury.
Using an optional bracket to mount the TV
• You can ask a qualified service professional about using an optional AN-37AG2/AN-52AG1 bracket to mount the TV to the wall.
• Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
AN-37AG2/AN-52AG1 wall mount bracket.
(See the bracket instructions for details.)
About setting the TV angle and height adjustment
AN-37AG2
AN-37AG2
AN-52AG1
Model
LC-32HT3U
Angle of TV
0/5/10°
LC-37HT3U/ 0/5°
LC-42HT3U
AN-52AG1 (LC-42HT3U only)
1 0/5/10/15/20°
Vertical mounting
Angular mounting
2 f1 63/64 (f5)/0/
e1 63/64 (e5)
• can be moved 1 63/64 (5) up or down
Unit: inch (cm)
NOTE
• Detach the cable clamps on the rear of the TV when using the optional mount bracket.
• Due to the terminal configuration on this TV, when you wall-mount this model, make sure there is enough space between the
wall and the TV for the cables.
19
Appendix
Troubleshooting
Problem
Possible Solution
• No power
• Check if you pressed TV POWER on the remote control unit. (See page 12.) If the
indicator on the TV does not light up, press POWER on the TV.
• Is the AC cord disconnected? (See page 16.)
• Has the power been turned on? (See page 18.)
• Unit cannot be operated.
• External influences such as lightning, static electricity, may cause improper
operation. In this case, operate the unit after first turning off the power of the TV or
unplugging the AC cord and replugging it in after 1 or 2 minutes.
• Remote control unit does not
operate.
•
•
•
•
•
• Picture is cut off/with sidebar
screen.
• Is the image position correct? *
• Are screen mode adjustments such as picture size made correctly? *
• Strange color, light color, or color
misalignment
• Adjust the picture tone. *
• Is the room too bright? The picture may look dark in a room that is too bright.
• Check the input signal setting. *
• Power is suddenly turned off.
• Is the sleep timer set? *
• Check the power control settings. *
• The unit's internal temperature has increased.
Remove any objects blocking vent or clean.
• No picture
•
•
•
•
•
•
• No sound
• Is the volume too low? *
• Is “Variable” selected in “Output Select”? *
• Have you pressed MUTE on the remote control unit? *
• The TV sometimes makes a
cracking sound.
• This is not a malfunction. This happens when the cabinet slightly expands and
contracts according to change in termperature. This does not affect the TV's
performance.
Is the FUNCTION set correctly? Set it to the TV setting position.
Are batteries inserted with polarity (e, f) aligned? *
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light illuminated near the remote control sensor?
Is connection to other components correct? *
Is correct input signal source selected after connection? *
Is the correct input selected? *
Is picture adjustment correct? *
Is “On” selected in “Audio Only”? *
Is a non-compatible signal being input? *
• See the OPERATION MANUAL FOR HOTEL OPERATOR for the Possible Solutions marked with an asterisk (*).
Troubleshooting-Digital broadcasting
The error message about reception of broadcast
The example of an error message
displayed on a screen
Error code
Possible Solution
• Failed to receive broadcast.
E202
• Check the antenna cable. Check that the antenna is correctly
setup.
• No broadcast now.
E203
• Check the broadcast time in the program guide.
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction.
Storage temperature: f4°F to e140°F (f20°C to e60°C)
20
Appendix
Specifications
Item
Model: LC-32HT3U
Model: LC-37HT3U
Model: LC-42HT3U
LCD panel
32o Advanced Super View
& BLACK TFT LCD
(Screen size 31 1/2o
measured diagonally)
37o Advanced Super View
& BLACK TFT LCD
(Screen size 37o
measured diagonally)
42o Advanced Super View
& BLACK TFT LCD
(Screen size 42 1/64o
measured diagonally)
Number of dots
3,147,264 dots (1366 g 768 g 3 dots)
TV
Function
TV-standard (CCIR)
American TV Standard ATSC/NTSC System
Receiving
Channel
VHF/UHF
VHF 2-13ch, UHF 14-69ch
CATV
1-135ch
Digital Terrestrial
Broadcast (8VSB)
2-69ch
Digital cable*1
(64/256 QAM)
1-135ch
Audio multiplex
Backlight
60,000 hours (at Backlight Standard position)
10W g 2
Audio out
Terminals
BTSC System
Rear
INPUT 1
AV in, COMPONENT in
INPUT 2
AV in , S-VIDEO in
AV in , COMPONENT in
INPUT 3
Audio in, COMPONENT in
AV in , S-VIDEO in
INPUT 4
HDMI in with HDCP
INPUT 5
Audio in, HDMI in with HDCP
INPUT 6
15 pin mini D-sub female connector, Audio in (Ø 3.5 mm jack)
ANTENNA
75 q Unbalance, F Type g 1 (VHF/UHF/CATV/ATSC/QAM)
DIGITAL AUDIO OUTPUT
Optical Digital audio output g 1 (PCM/Dolby Digital)
OUTPUT
Audio out
TRANSPORT
RJ-11
OSD language
English/French/Spanish
Power Requirement
AC 120 V, 60 Hz
Power Consumption
152 W
185 W
235 W
TVestand
40.8 lbs./18.5 kg
50.7 lbs./23.0 kg
67.2 lbs./30.5 kg
TV only
35.3 lbs./16.0 kg
43.0 lbs./19.5 kg
59.5 lbs./27.0 kg
TVestand
3111/32 g 2313/64 g 937/64 inch 3561/64 g 2527/32 g 1135/64 inch 4019/32 g 287/8 g 111/2 inch
TV only
3111/32 g 2059/64 g 353/64 inch 3561/64 g 2337/64 g 353/64 inch 4019/32 g 2637/64 g 59/32 inch
Weight
Dimension*2
(W g H g D)
Operating temperature
e32°F to e104°F (0°C to e40°C)
*1 Emergency alert messages via Cable are unreceivable.
*2 The dimensional drawings are shown on the inside back cover.
• As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specification figures indicated are nominal values of production units.
There may be some deviations from these values in individual units.
Optional accessory
The listed optional accessory is available for the Liquid
Crystal Television. Please purchase it at your nearest shop.
• Additional optional accessories may be available in the near
future. When purchasing, please read the newest catalogue for
compatibility and check the availability.
Part name
Model number
Wall mount bracket
AN-37AG2
AN-52AG1 (LC-42HT3U only)
21
Appendix
Information on the software license for this product
Software composition
The software included in this product is comprised of various software components whose individual copyrights
are held by SHARP or by third parties.
Software developed by SHARP and open source software
The copyrights for the software components and various relevant documents included with this product that
were developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international
treaties, and other relevant laws. This product also makes use of freely distributed software and software
components whose copyrights are held by third parties. These include software components covered by a GNU
General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license
agreement.
Obtaining source code
Some of the open source software licensors require the distributor to provide the source code with the executable
software components. GPL and LGPL include similar requirements. For information on obtaining the source code
for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the
following website:
http://www.sharpusa.com/gpl
We are unable to answer any questions about the source code for the open source software. The source code for
the software components whose copyrights are held by SHARP is not distributed.
Acknowledgements
The following open source software components are included in this product:
• linux kernel
• busybox
• uClibc
• zlib
• libpng
• libjpeg
22
Calling for Service
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or
customer assistance, please call 1-800-BE-SHARP.
LIMITED WARRANTY
HOSPITALITY/LODGING COMMERCIAL APPLICATION LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first end user purchaser that this commercial application Sharp brand product (the
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option,
either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the
purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any cosmetic or consumable items of the Product or if the serial number or model number affixed to the
Product has been removed, defaced, changed, altered or tampered with. This warranty does not cover installation or signal reception
problems
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below. The purchaser must be able
to provide proof of purchase to the servicer, which proof must include the date of purchase.
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or
implied. Specifically ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR
PURPOSE ARE SPECIFICALLY EXCLUDED. IF, UNDER APPLICABLE STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE
DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF
PURCHASE SET FORTH BELOW.
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy
available to the purchaser and only for the time periods set forth herein. Correction of defects, in the manner and for the period of time
described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. Sharp does
not warrant nor shall Sharp be liable, or in any way responsible, for Products which have been subject to abuse (including, but not limited
to, improper voltage), accident, misuse, negligence, lack of reasonable care, alteration, modification, tampering, misuse, improper
operation or maintenance or any damages or defects in the Product which were caused by repairs or attempted repairs performed by
anyone other than a Sharp authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential
economic or property damage. Some states do not allow limits on warranties or on remedies for breach in certain transactions; in such
states, the limits herein may not apply.
Model Specific Section (On-Site Service)
Your Product Model Number & Description:
LC-32HT3U, LC-37HT3U, LC-42HT3U Hospitality LCD TV
(Be sure to have this information available when you need service for your
Product.)
Warranty Period for this Product:
Two (2) years parts and labor from date of purchase.
Additional Exclusions:
In order for the Product to be serviced, the Product must be readily available
to the servicer, free and clear of any installation, mounting or other encumbrance which would interfere with servicing the Product.
The servicer will not reinstall or remount the Product after service. Any labor
and materials required to remove and/or reinstall a Product are the responsibility of the end-user.
Image retention or burn-in resulting from fixed images displayed for long
periods of time
Where to Obtain Service:
From a Sharp Authorized Servicer located in the United States. To find the
location of the nearest Sharp Authorized Servicer, call Sharp toll free at 1800-BE-SHARP.
What to do to Obtain Service:
Contact your Sharp Authorized Servicer to obtain on-site service for this
product. The Servicer will come to your location and if necessary remove the
unit for repair at the Servicer’s facility. Be sure to have Proof of Purchase
available.
TO OBTAIN PRODUCT INFORMATION OR ACCESSORIES, CALL 1-800-BE-SHARP
OR VISIT www.sharpusa.com
23
END-USER LIMITED WARRANTY
Sharp Electronics Of Canada Limited warrants to the first end user purchaser that this Sharp brand product (the “Product”)
when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its
option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at
no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or
other misuse, abnormal service or handling, or which has been altered or modified in design or construction. In order to
enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of
purchase to the servicer.
To the extent permitted by applicable provincial law, the warranties set forth herein are in lieu of, and exclusive of, all other
warranties, express or implied. Specifically, ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE
EXCLUDED. ALL EXPRESS AND IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY,
FITNESS FOR USE, AND FITNESS FOR A PARTICULAR PURPOSE ARE SPECIFICALLY EXCLUDED. If, under applicable
provincial law, implied warranties may not validly be disclaimed or excluded, the duration of such implied warranties is
limited to the period(s) from the date of purchase set forth below.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were
caused by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable
or in any way responsible for any incidental or consequential economic or property damage. Some provinces do not allow
limits on warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.
Model Specific Section (On-Site Service)
Your Product Model Number & Description:
LC-32HT3U, LC-37HT3U, LC-42HT3U Hospitality LCD TV
Warranty Period for this Product:
Additional Item(s) Excluded from
Warranty Coverage (if any):
Two (2) years parts & labor from date of purchase
Labor and materials required to remove and reinstall in
custom enclosures, and TV’s connected to third party
control and automation systems.
What to do to Obtain Service:
Contact your Sharp Authorized Servicer to obtain on-site
service for this Product.
24
Dimensional drawings
Unit: inch/(mm)
LC-32HT3U
31 /32 (796)
131/2 (343)
2059/64 (531)
1945/64 (500)
1945/64 (500)
353/64 (97)
39/32 (83)
77/8 (200)
77/8 (200)
323/64 (85)
29/32 (58)
2313/64 (589)
279/16 (700.0)
1535/64 (394.6)
11
937/64 (243)
LC-37HT3U
3561/64 (913)
1817/64 (463.8)
2337/64 (599)
1427/32 (377)
2135/64 (547)
2135/64 (547)
1
2 /4 (57)
2527/32 (656)
3225/64 (822.6)
45/8 (117)
353/64 (97)
77/8 (200)
23
3 /64 (85)
77/8 (200)
1135/64 (293)
Dimensional drawings
Unit: inch/(mm)
LC-42HT3U
4019/32 (1031)
2117/64 (540)
1637/64 (421)
2023/32 (526)
2637/64 (675)
29/32 (58)
287/8 (733)
3647/64 (933)
2117/64 (540)
325/32 (95)
59/32 (134)
77/8 (200)
323/64 (85)
77/8 (200)
111/2 (292)
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
SHARP CORPORATION
Printed in Mexico
Imprimé au Mexique
Impreso en México
TINS-D139WJZZ
07P08-MX-NG
Download PDF

advertising