Sharp | MX-M283 | Owner's Manual | Sharp MX-M283 Owner's Manual

mxm503_us_saf.fm
-1 ページ
2009年5月14日 木曜日 午後8時25分
MODEL: MX-M283N
MX-M363N
MX-M453N
MX-M503N
DIGITAL MULTIFUNCTIONAL SYSTEM
Safety Guide
Before installing this product, be sure to read the
"CAUTIONS" and "INSTALLATION
REQUIREMENTS" sections.
CAUTIONS
INSTALLATION REQUIREMENTS
SUPPLIES
SPECIFICATIONS
TO THE ADMINISTRATOR OF THE MACHINE
Keep this manual close at hand for reference
whenever needed.
mxm503_us_saf.fm
0 ページ
2009年5月14日 木曜日 午後8時25分
Each instruction also covers the optional units used with these products.
Caution!
For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
To reduce the risk of fire, use only UL-Listed No.26 AWG or larger telecommunication line cord.
FAX interface cable and Line cable:
These special accessories must be used with the device.
FOR YOUR RECORDS ...
To protect against loss or theft, record and retain for reference the machine's serial number located at the lower left corner of the left
side of the machine.
Model Number
Serial Number
Date of Purchase
Place of Purchase
Authorized Sharp Printer
Service Department Number
Notice for Users in U.S.A.
EMC (this machine and peripheral devices)
WARNING:
FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the
manufacturer could void the user's authority to operate this equipment.
Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This machine contains the software having modules developed by Independent JPEG Group.
This product includes Adobe® Flash® technology of Adobe Systems Incorporated.
Copyright© 1995-2007 Adobe Macromedia Software LLC. All rights reserved.
mxm503_us_saf.fm
1 ページ
2009年5月14日 木曜日 午後8時25分
Contents
CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Finisher specifications . . . . . . . . . . . . . . . . . . . . . 13
Laser information . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Finisher (large stacker) specifications . . . . . . . . . 14
INSTALLATION REQUIREMENTS . . . . . . . . . . . . . 5
SUPPLIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Storage of supplies. . . . . . . . . . . . . . . . . . . . . . . . . 6
Supply of spare parts and consumables . . . . . . . . 6
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Machine specifications / copier specifications . . . . 7
Continuous copying speeds . . . . . . . . . . . . . . . . . . 9
Ambient environment . . . . . . . . . . . . . . . . . . . . . . . 9
Saddle stitch finisher specifications . . . . . . . . . . . 15
Punch module specifications (for finisher) . . . . . . 16
Punch module specifications (for finisher (large
stacker)) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Punch module specifications
(for saddle stitch finisher) . . . . . . . . . . . . . . . . . . . 16
Printer specifications . . . . . . . . . . . . . . . . . . . . . . 17
Network scanner / Internet Fax specifications . . . 18
Pull scan function (TWAIN) specifications . . . . . . 19
Facsimile specifications . . . . . . . . . . . . . . . . . . . . 20
Acoustic noise emission
(measurement according to ISO7779) . . . . . . . . . 10
TO THE ADMINISTRATOR OF THE MACHINE . . 22
Automatic document feeder specifications. . . . . . 10
Factory default passwords . . . . . . . . . . . . . . . . . . 22
Exit tray unit (right tray) specifications . . . . . . . . . 11
Forwarding all transmitted and received data to the
administrator (document administration function). . . .22
Stand/1x500 sheet paper drawer specifications. . 11
Stand/2x500 sheet paper drawer specifications. . 12
For the users of the fax function . . . . . . . . . . . . . . . . .23
Large capacity tray specifications . . . . . . . . . . . . 12
Trademark acknowledgments . . . . . . . . . . . . . . . 27
Note:
• Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please
contact your dealer or nearest SHARP Service Department.
• This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is
discovered, please contact your dealer or nearest SHARP Service Department.
• Aside from instances provided for by law, SHARP is not responsible for failures occurring during the use of the product or its
options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due
to use of the product.
Products that have earned the ENERGY STAR® are designed to protect the environment
through superior energy efficiency.
The Ecologo Program guidelines are applied to the products only in Canada. The products that
meet the Ecologo Program guidelines carry the logo shown to the left. The products without the
logo may not meet the Ecologo Program guidelines.
Warranty
While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no
warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not
responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.
© Copyright SHARP Corporation 2009. All rights reserved. Reproduction, adaptation or translation without prior written
permission is prohibited, except as allowed under copyright laws.
1
mxm503_us_saf.fm
2 ページ
2009年5月14日 木曜日 午後8時25分
CAUTIONS
Symbols in this manual
To ensure safe use of the machine, this manual uses various safety symbols. The safety symbols are classified as explained below.
Be sure you understand the meaning of the symbols when reading the manual.
WARNING Indicates a risk of death or serious injury.
CAUTION
Indicates a risk of human injury or property damage.
Meaning of the symbols
The
symbol indicates the need for caution. The specific matter that requires caution is indicated inside the symbol (the
symbol at left indicates "caution: high temperature").
The
symbol indicates an action that is prohibited. The specific action that is prohibited is indicated inside or beside the
symbol (the symbol at left indicates "disassembly is prohibited").
The
symbol indicates an action that is mandatory.
WARNING
Be sure to connect the power cord only to a
power outlet that meets the specified voltage
and current requirements. Also make certain
the outlet is properly grounded. Do not use an
extension cord or adapter to connect other
devices to the power outlet used by the machine. Using
an improper power supply may cause fire or electrical
shock.
*For the power supply requirements, see the name
plate in the lower left corner of the left side of the
machine.
Do not place a container of water
or other liquid, or a metal object
that might fall inside, on the
machine.
If the liquid spills or the object
falls into the machine, fire or
electrical shock may result.
Do not damage or modify the
power cord.
Placing heavy objects on the
power cord, pulling it, or
forcibly bending it will damage
the cord, resulting in fire or
electrical shock.
Do not remove the machine casing.
High-voltage parts inside the machine may
cause electrical shock.
Do not make any modifications to this
machine.
Doing so may result in personal injury or
damage to the machine.
2
If you notice smoke, a strange odor, or other
abnormality, do not use the machine.
If used in this condition, fire or electrical
shock may result.
Immediately switch off the main
power and remove the power plug
from the power outlet. Contact
your dealer or nearest SHARP
Service Department.
If a thunder storm begins, switch off the main
power and remove the power plug from the
outlet to prevent electrical shock and fire due
to lightning.
If a piece of metal or water enters the
machine, switch off the main power and
remove the power plug from the power outlet.
Contact your dealer or nearest SHARP
Service Department. Using the machine in
this condition may result in electrical shock
or fire.
Do not insert or remove the power plug with
wet hands.
This may cause electrical shock.
Do not use a flammable spray to clean the
machine.
If gas from the spray comes in contact with
hot electrical components or the fusing unit
inside the machine, fire or electrical shock
may result.
mxm503_us_saf.fm
3 ページ
2009年5月14日 木曜日 午後8時25分
CAUTIONS
CAUTION
Do not install the machine in a location with poor ventilation. Install so
that exhaust from the machine does not directly contact people.
A small amount of ozone is produced within the printer during operation. The
emission level is insufficient to cause any health hazard.
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3)
calculated as an 8 hr. time-weighted average concentration.
However, since the small amount that is emitted may have an objectionable odor, it is
advisable to place the copier in a ventilated area.
Do not install the machine on an unstable or
slanted surface. Install the machine on a surface
that can withstand the weight of the machine.
Risk of injury due to the machine falling or
toppling. If peripheral devices are to be installed, do not
install on an uneven floor, slanted surface, or otherwise
unstable surface. Danger of slippage, falling, and toppling.
Install the product on a flat, stable surface that can
withstand the weight of the product. (Weight when various
peripheral devices are installed: approx. 441 lbs. (200 kg))
When removing the power plug from the
outlet, do not pull on the cord.
Pulling on the cord may cause damage such as
wire exposure and breakage, and may result in
fire or electrical shock.
Do not look directly at the
light source.
Doing so may damage your
eyes.
When the machine is installed, the adjusters
(4) must be lowered to the floor to secure the
machine (prevent it from moving).
Rotate the adjusters in the locking direction until
they are in firm contact with the floor.
If you find it necessary to
reposition the machine due to
rearrangement of your office
layout or other reason, retract
the adjusters from the floor,
turn off the power, and then
move the machine.
Adjuster
(After moving the machine,
lower the adjusters again to
Release
Lock
secure the machine.)
The fusing unit is hot.
When removing a
misfeed, do not touch the
fusing unit. Take care not
to burn yourself.
Fusing unit
Do not block the ventilation ports on the
machine. Do not install the machine in a
location that will block the ventilation ports.
Blocking the ventilation ports will cause heat to
build up in the machine, creating a risk of fire.
Do not throw toner, a toner container (toner
cartridge), or a waste toner box into a fire.
Toner may fly and cause burns.
When loading paper,
removing a misfeed,
performing maintenance,
closing the front and
side covers, and
inserting and removing
trays, take care that your
fingers are not pinched.
Do not install in a location with
moisture or dust.
Risk of fire and electrical shock.
If you will not use the machine for a long
time, be sure to remove the power plug
from the outlet for safety.
Store toner, toner containers (toner
cartridges), and waste toner boxes out of
the reach of children.
When moving the machine, switch off the
main power and remove the power plug from
the outlet before moving.
The cord may be damaged, creating a risk of fire
or electrical shock.
The machine includes the document filing function, which stores document image data on the machine's hard drive. Stored
documents can be called up and printed or transmitted as needed. If a hard drive failure occurs, it will no longer be possible to
call up the stored document data. To prevent the loss of important documents in the unlikely event of a hard drive failure,
keep the originals of important documents or store the original data elsewhere.
With the exception of instances provided for by law, Sharp Corporation bears no responsibility for any damages or loss due to
the loss of stored document data.
3
mxm503_us_saf.fm
4 ページ
2009年5月15日 金曜日 午前11時51分
CAUTIONS
Laser information
Wave length
790 nm ± 10 nm
Pulse times
(North America and Europe)
MX-M283N/MX-M363N: 6.1 µs ± 8.3 ns /7 mm
MX-M453N/MX-M503N: 4.8 µs ± 6.4 ns /7 mm
Output power
Max 0.6 mW (LD1+ LD2)
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1 Edition 1.2-2001)
For North America:
SAFETY PRECAUTIONS
This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that
the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.
• Do not remove the cabinet, operation panel or any other covers.
• The equipment's exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges
or other items into switch slots.
For Europe:
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
"BATTERY DISPOSAL"
THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED OF PROPERLY.
PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORIZED SERVICE REPRESENTATIVE FOR ASSISTANCE IN
DISPOSING OF THIS BATTERY.
This product utilizes a CR coin Lithium battery which contains a Perchlorate material. Special handling for this material may apply,
California residents, See www.dtsc.ca.gov/hazardouswaste/perchlorate/
Others, consult local environmental officers.
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these materials may be
regulated due to environmental consideration. For disposal or recycling information, please contact your local authorities, the
Electronics Industries Alliance: www.eiae.org, the lamp recycling organization: www.lamprecycle.org or Sharp at 1-800-BE-SHARP.
(For U.S.A. Only)
4
mxm503_us_saf.fm
5 ページ
2009年5月14日 木曜日 午後8時25分
INSTALLATION REQUIREMENTS
The performance of the machine is affected by the ambient conditions of the installation location. Do not install in the
following locations:
CAUTION:
Do not install the machine in a location
with poor air circulation.
A small amount of ozone is created inside the machine during
printing. The amount of ozone created is not sufficient to be
harmful; however, an unpleasant odor may be noticed during
large copy runs, and thus the machine should be installed in a
room with a ventilation fan or windows that provide sufficient
air circulation. (The odor may occasionally cause headaches.)
Dusty locations
If dust enters the machine, dirty output and machine failure
may result.
Locations exposed to direct sunlight
* Install the machine so that people are not directly
exposed to exhaust from the machine. If installed near a
window, ensure that the machine is not exposed to direct
sunlight.
Locations that are excessively hot, cold,
humid, or dry (near heaters, humidifiers, air
conditioners, etc.)
The paper will become damp and condensation may form
inside the machine, causing misfeeds and dirty output.
☞ Ambient environment (page 9)
If the location has an ultrasonic humidifier, use pure water for
humidifiers in the humidifier. If tap water is used, minerals
and other impurities will be emitted, causing impurities to
collect on the inside of the machine and create dirty output.
Plastic parts may become deformed and dirty output may
result.
Locations with ammonia gas
Installing the machine next to a diazo copy machine may
cause dirty output.
Locations subject to vibration.
Vibration may cause failure.
Near a wall
Be sure to allow the required space around the machine for
servicing and proper ventilation. (The machine should be no
closer than the distances indicated below from walls. The
indicated distances are for the case when a saddle finisher
and large capacity paper tray are not installed.)
11-13/16"
(30cm)
11-13/16"
(30cm)
17-23/32"
(45cm)
The machine includes a built-in hard drive. Do not subject the machine to shock or vibration. In particular, never
move the machine while the power is on.
• The machine should be installed near an accessible power outlet for easy connection.
• Connect the machine to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the
same outlet, the light may flicker.
5
mxm503_us_saf.fm
6 ページ
2009年5月14日 木曜日 午後8時25分
SUPPLIES
Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher
staple cartridge, and transparency film.
For best copying results, be sure to use only Sharp Genuine Supplies which are designed,
engineered, and tested to maximize the life and performance of Sharp products. Look for the
Genuine Supplies label on the toner package.
GENUINE SUPPLIES
Storage of supplies
Proper storage
1. Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight.
2. Store paper in the wrapper and lying flat.
3. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds.
Storing toner cartridges
Store a new toner cartridge box horizontally with the top side up. Do not store a toner cartridge standing on end. If stored
standing on end, the toner may not distribute well even after shaking the cartridge vigorously, and will remain inside the
cartridge without flowing out.
Staple cartridge
The finisher and saddle stitch finisher require the following staple cartridge:
MX-SCX1 (for finisher and saddle stitch finisher)
Approx. 5000 per cartridge x 3 cartridges
AR-SC2 (for finisher (large stacker))
Approx. 5000 per cartridge x 3 cartridges
AR-SC3 (for saddle stitch finisher only)
Approx. 2000 per cartridge x 3 cartridges
Supply of spare parts and consumables
The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of
production. Spare parts are those parts of the machine which may break down within the scope of the ordinary use of
the product, whereas those parts which normally exceed the life of the product are not to be considered as spare parts.
Consumables too, are available for 7 years following the termination of production.
6
mxm503_us_saf.fm
7 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Machine specifications / copier specifications
Name
Digital Multifunctional System MX-M283N/MX-M363N/MX-M453N/MX-M503N
Type
Desktop
Photoconductive type
OPC drum
Printing method
Electrophotographic system (laser)
Developer system
Dry-type two-component magnetic brush development
Fusing system
Heat rollers
Document glass
Scanning resolution
600 x 300 dpi (factory default values), 600 x 400 dpi,
600 x 600 dpi
600 x 300 dpi (factory default values), 600 x 400 dpi,
Automatic document feeder
(MX-M363N/MX-M453N/MX-M503N) 600 x 600 dpi
Automatic document feeder
(MX-M283N)
600 x 400 dpi (factory default values), 600 x 600 dpi
Printing resolution
1200 x 1200 dpi, 600 x 600 dpi
Scanning gradation
256 levels
Printing gradation
Equivalent to 256 levels
Original sizes / types
Max. 11" x 17" (A3) / sheets, bound documents
Copy sizes
Maximum: 12" x 18" (A3W) Minimum: 5-1/4" x 5-3/4" (A5R)
Print margins
Leading edge / trailing edge: total 21/64" (8 mm) or less,
near edge / far edge: total 11/64" ±3/32" (4 mm ±2 mm) or less
Warm-up time
20 seconds or less
(This may vary depending on the ambient conditions.)
First-copy time*
MX-M283N/MX-M363N: 4.6 seconds or less
MX-M453N/MX-M503N: 3.9 seconds or less
(Portrait feeding of 8-1/2" x 11" (A4) sheets. This may vary depending on the state of the machine.)
Copy ratios
Variable: 25% to 400% in increments of 1%, total 376 increments (25% to 200% when the automatic
document feeder is used)
Fixed presets: 25%, 50%, 64%, 77%, 100%, 121%, 129%, 200% and 400% for inch sizes;
25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% and 400% for AB sizes.
Two reduction ratios and two enlargement ratios can be stored.
Continuous copy
999 copies
Automatic document
feeder
See "Automatic document feeder specifications".
Paper sizes:
Tray 1 / Tray 2
11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, A3, B4, A4, A4R, B5, B5R, A5R,
8K, 16K, 16KR (Includes automatic paper size detection function.)
Paper weight: Plain paper (16 lbs. to 28 lbs. (60 g/m2 to 105 g/m2)), heavy paper (28 lbs. bond to
110 lbs. index (106 g/m2 to 209 g/m2))
Paper capacity: Plain paper (21 lbs. (80 g/m2)) 500 sheets, heavy paper 200 sheets
Paper types:
SHARP-recommended plain paper, recycled paper, colored paper, and heavy paper
* First copy out time is measured with original on the document glass in full ready condition with fuser at operating temperature and
mirror motor at operating speed in black and white mode, actual time may vary based on environment conditions.
7
mxm503_us_saf.fm
8 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Machine specifications / copier specifications (Continued)
Paper sizes: 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",
8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, envelopes, A3W, A3,
B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR (Includes automatic paper size detection
function. Entry of paper sizes up to 11-5/8" x 17" (297 mm x 432 mm) is possible.)
Bypass tray
Paper weights:
Thin paper (15 lbs. to 16 lbs. (56 g/m2 to 59 g/m2)), plain paper (16 lbs. to 28 lbs. (60 g/m2 to
105 g/m2)), heavy paper (28 lbs. bond to 110 lbs. index (106 g/m2 to 209 g/m2)),
envelopes (20 lbs. to 24 lbs. (75 g/m2 to 90 g/m2))
Paper capacity: Standard paper 100 sheets
Paper types:
SHARP-recommended plain paper, recycled paper, colored paper, heavy paper, thin paper,
transparency film, labels, tab paper, envelopes (Monarch, Com-10, DL, C5)
Duplex module
Paper sizes: 11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 5-1/2" x 8-1/2"R, A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR
Paper weight: Plain paper (16 lbs. to 28 lbs. (60 g/m2 to 105 g/m2)), heavy paper (28 lbs. bond to
110 lbs. index (106 g/m2 to 209 g/m2))
Paper types: SHARP-recommended plain paper, recycled paper, colored paper, and heavy paper
Output method: Face-down output (12" x 18" and A3W paper can be output to right tray, finisher, or
saddle stitch finisher)
Output capacity: 400 sheets (using SHARP-recommended 8-1/2" x 11" or A4 paper)
1
Output tray (Center tray)*
(The maximum number of sheets that can be held varies depending on ambient conditions in the
installation location, the type of paper, and the storage conditions of the paper.)
Tray full sensor: Yes
Interface port
LAN connectivity: 10Base-T / 100Base-TX / 1000Base-T
USB connectivity: Type A connector supports USB 2.0*2
Compatibility requirements of USB memory
Memory capacity : Max. 32 GB
Disk Format
: FAT32 only
Type B connector supports USB 2.0 (Hi speed)
Required power supply
AC 120 V ±10% 60 Hz
Power consumption
1.44kW
Dimensions
25-25/64" (W) x 27-3/8" (D) x 36-51/64" (H) (645 mm (W) x 695 mm (D) x 935 mm (H))
Weight
Approx. 209.4 lbs. (95 kg)
Overall dimensions
38-53/64" (W) x 27-3/8" (D) (986 mm (W) x 695 mm (D)) (when bypass tray is extended)
*1 Output tray (Center tray) cannot be used when the finisher or saddle stitch finisher is installed.
*2 Type A connectors are located on the front of the machine and on the right side of the machine at the back (total of two
connectors. Do not use the connectors simultaneously.
To receive power supplied from a type A connector, the total current consumption of the connected device should not exceed
500 mA.
8
mxm503_us_saf.fm
9 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Continuous copying speeds*
Model
MX-M283N
Copy ratio
MX-M363N
MX-M453N
MX-M503N
100% / Reduce / Enlarged
11" x 17", A3, 8K
15 copies/min.
17 copies/min.
20 copies/min.
22 copies/min.
8-1/2" x 14", 8-1/2" x 13-1/2",
8-1/2" x 13-2/5", 8-1/2" x 13",
B4
17 copies/min.
20 copies/min.
23 copies/min.
25 copies/min.
8-1/2" x 11", A4, B5, 16K
28 copies/min.
36 copies/min.
45 copies/min.
50 copies/min.
8-1/2" x 11"R,
7-1/4" x 10-1/2"R, A4R, B5R,
16KR
20 copies/min.
25 copies/min.
30 copies/min.
30 copies/min.
* Copy speed during output of the second copy and following copies when performing continuous one-sided copying of the same
page (excluding offset output) using plain one-sided paper from a tray other than the bypass tray.
Ambient environment
(Humidity)
85%
60%
20%
54˚F
(10˚C)
86˚F 91˚F (Temperature)
(30˚C) (35˚C)
9
mxm503_us_saf.fm
10 ページ
2009年5月15日 金曜日 午後3時20分
SPECIFICATIONS
Acoustic noise emission (measurement according to ISO7779)
MX-M283N
MX-M363N
MX-M453N
MX-M503N
Printing mode (continuous printing)
6.4 B
6.6 B
6.7 B
6.8 B
Standby mode
4.0 B
4.6 B
4.6 B
4.6 B
Bystander positions
50 dB (A)
52 dB (A)
53 dB (A)
54 dB (A)
Operator positions
51 dB (A)
52 dB (A)
53 dB (A)
53 dB (A)
Bystander positions
27 dB (A)
32 dB (A)
32 dB (A)
32 dB (A)
Operator positions
28 dB (A)
34 dB (A)
32 dB (A)
31 dB (A)
Sound power level LwA
Sound pressure level LpA (actual measurement)
Printing mode
Standby mode
Emission concentration
(measurement according to RAL-UZ122: Edition Jun. 2006)
Measured substance
Machine state
Ozone
Dust
Styrene
Color mode
Diffusion speed
Black & white
1.5 mg/h or less
Color
3.0 mg/h or less
Black & white
4.0 mg/h or less
Color
4.0 mg/h or less
Black & white
1.0 mg/h or less
Color
1.8 mg/h or less
Black & white
Less than 0.05 mg/h
Color
Less than 0.05 mg/h
Black & white
10 mg/h or less
Color
18 mg/h or less
During copying operation
Benzene
TVOC
Standby
2.0 mg/h or less
Automatic document feeder specifications
MX-M283N
MX-M363N/MX-M453N/MX-M503N
Original sizes
11" x 17" to 5-1/2" x 8-1/2", A3 to A5, long paper
(max. width 11-5/8" (297 mm) x max. length 39-23/64"*1 (1000 mm))
Original weight
One-sided 9 lbs. to 34 lbs. (35 g/m2 to 128 g/m2)*2 One-sided 9 lbs. to 34 lbs. (35 g/m2 to 128 g/m2)*2
Two-sided 13 lbs. to 28 lbs. (50 g/m2 to 105 g/m2) Two-sided 13 lbs. to 34 lbs. (50 g/m2 to 128 g/m2)
Capacity
100 sheets (21 lbs. (80 g/m2)) Maximum stack height of 1/2" (13 mm)
*1 Scanning in mono 2 mode of one side only is possible in fax and scan send modes. However, when the resolution is 600 x 600 dpi
in Internet fax mode, the maximum length is 31-31/64" (800 mm). When the resolution is 400 x 400 dpi or 600 x 600 dpi in scan
mode, a long original cannot be scanned.
*2 Paper weights from 9 lbs. (35 g/m2) to 13 lbs. (49 g/m2) require the use of slow scan mode.
10
mxm503_us_saf.fm
11 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Exit tray unit (right tray) specifications
Model
MX-TRX2
Output method
Face-down output
Output capacity*
100 sheets (using SHARP-recommended 8-1/2" x 11" or A4 paper)
Dimensions
When tray is folded up:
12-23/64" (W) x 15-61/64" (D) x 2-3/64" (H) (314 mm (W) x 405 mm (D) x 52 mm (H))
When tray is extended:
17-31/64" (W) x 15-61/64" (D) x 2-3/64" (H) (444 mm (W) x 405 mm (D) x 52 mm (H))
Weight
Approx. 2 lbs. (0.93 kg)
* The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of
paper, and the storage conditions of the paper. Envelopes and tab paper cannot be output.
Stand/1x500 sheet paper drawer specifications
Model
MX-DEX8
Paper sizes
11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
7-1/4" x 10-1/2"R, A3, B4, A4, A4R, B5, B5R, 8K, 16K, 16KR
Paper weight
Plain paper (16 lbs. to 28 lbs. (60 g/m2 to 105 g/m2)), heavy paper (28 lbs. bond to 110 lbs. index
(106 g/m2 to 209 g/m2))
Paper capacity
500 sheets (21 lbs. (80 g/m2)) x 1 tray
Paper types
SHARP-recommended plain paper, recycled paper, and colored paper
Automatic paper size
detection
When "Auto-Inch" detection is selected:
11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R
When "Auto-AB" detection is selected:
A3, B4, A4, A4R, B5, B5R, 216 mm x 330 mm (8-1/2" x 13")
Power supply
Supplied from the machine
Dimensions
28-11/32" (W) x 26-3/8" (D) x 11-15/16" (H) (720 mm (W) x 670 mm (D) x 303 mm (H))
(including adjuster)
Weight
Approx. 44.1 lbs. (20 kg)
11
mxm503_us_saf.fm
12 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Stand/2x500 sheet paper drawer specifications
Model
MX-DEX9
Paper sizes
11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
7-1/4" x 10-1/2"R, A3, B4, A4, A4R, B5, B5R, 8K, 16K, 16KR
Paper weight
Plain paper (16 lbs. to 28 lbs. (60 g/m2 to 105 g/m2)), heavy paper (28 lbs. bond to 110 lbs. index
(106 g/m2 to 209 g/m2))
Paper capacity
500 sheets (21 lbs. (80 g/m2)) x 2 tray
Paper types
SHARP-recommended plain paper, recycled paper, and colored paper
Automatic paper size
detection
When "Auto-Inch" detection is selected:
11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R
When "Auto-AB" detection is selected:
A3, B4, A4, A4R, B5, B5R, 216 mm x 330 mm (8-1/2" x 13")
Power supply
Supplied from the machine
Dimensions
28-11/32" (W) x 26-3/8" (D) x 11-15/16" (H) (720 mm (W) x 670 mm (D) x 303 mm (H))
(including adjuster)
Weight
Approx. 51.9 lbs. (23.5 kg)
Large capacity tray specifications*
Model
MX-LCX1
Paper sizes
8-1/2" x 11", A4 (paper size change must be performed by a service technician)
Paper weight
Plain paper (16 lbs. to 28 lbs. (60 g/m2 to 105 g/m2))
Paper capacity
3500 sheets (21 lbs. (80 g/m2))
Paper types
SHARP-recommended plain paper, recycled paper, and colored paper
Power supply
Supplied from the machine
Dimensions
14-9/16" (W) x 21-21/32" (D) x 20-15/32" (H) (370 mm (W) x 550 mm (D) x 520 mm (H))
Weight
Approx. 63.9 lbs. (29 kg)
* A stand/1x500 sheet paper drawer or stand/2x500 sheet paper drawer is required to connect the large capacity tray to the machine.
12
mxm503_us_saf.fm
13 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Finisher specifications
Model
MX-FNX9
Paper sizes
12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, envelopes, A3W, A3, B4, A4, A4R, B5, B5R,
A5R, 8K, 16K, 16KR
Paper weight
Thin paper (15 lbs. to 16 lbs. (56 g/m2 to 59 g/m2)) plain paper (16 lbs. to 28 lbs. (60 g/m2 to 105 g/m2))
heavy paper (28 lbs. bond to 110 lbs. index (106 g/m2 to 209 g/m2)) , envelopes (20 lbs. to 24 lbs.
(75 g/m2 to 90 g/m2))
Modes
Non-staple, staple
Allowed paper sizes for
offset
11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
A3, B4, A4, A4R, B5, 8K, 16K
Offset distance
1-3/16" (30 mm)
Tray capacity*1
Non-stapling*2:
500 sheets*3 (8-1/2" x 11", 8-1/2" x 11"R,
7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, A4, A4R, B5,
B5R, A5R, 16K, 16KR)
250 sheets*4 (12" x 18", 11" x 17", 8-1/2" x 14",
8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",
A3W, A3, B4, 8K)
Power supply
Supplied from the machine
Dimensions
25-3/16" (W) x 23-27/64" (D) x 8-5/64" (H) (640 mm (W) x 595 mm (D) x 205 mm (H))
(When tray is extended)
Weight
Approx. 28.7 lbs. (13 kg)
Stapling*5:
30 sets or 500 sheets*3 (8-1/2" x 11",
8-1/2" x 11"R, A4, A4R, B5, 16K, 16KR)
30 sets or 250 sheets*4 (11" x 17", 8-1/2" x 14",
8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",
A3, B4, 8K)
Stapler section
Allowed paper sizes for
stapling
11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
A3, B4, A4, A4R, B5, 8K, 16K, 16KR
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two
staples.)
Maximum number of
sheets for stapling*5
50 sheets (8-1/2" x 11", 8-1/2" x 11"R, A4, A4R, B5, 16K, 16KR)
30 sheets (11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", A3, B4, 8K)
(30 sheets when the sheets are the same width but different lengths.)
*1 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of
paper, and the storage conditions of the paper.
*2 Up to 10 envelopes can be output.
*3 The height of the sheets must not exceed 2-51/64" (71 mm).
*4 The height of the sheets must not exceed 1-13/32" (35.5 mm).
*5 The maximum number of sheets for stapling assumes a paper weight of 24 lbs. (90 g/m2) and includes two cover sheets of 28 lbs.
bond to 110 lbs. index (106 g/m2 to 209 g/m2).
Note:
Special media such as transparency film and label sheets cannot be stapled or punched.
13
mxm503_us_saf.fm
14 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Finisher (large stacker) specifications*1
Model
MX-FN11
Paper sizes
12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, envelopes, A3W, A3, B4, A4, A4R, B5, B5R,
A5R, 8K, 16K, 16KR
Paper weight
Thin paper (15 lbs. to 16 lbs. (56 g/m2 to 59 g/m2)) plain paper (16 lbs. to 28 lbs. (60 g/m2 to 105 g/m2))
heavy paper (28 lbs. bond to 110 lbs. index (106 g/m2 to 209 g/m2)) , envelopes (20 lbs. to 24 lbs.
(75 g/m2 to 90 g/m2))
Modes
Non-staple, staple
Allowed paper sizes for
offset
11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
A3, B4, A4, A4R, B5, 8K, 16K
Offset distance
1-3/16" (30 mm)
Upper tray
Non-stapling*3:
1550 sheets (8-1/2" x 11", 5-1/2" x 8-1/2"R, A4,
B5, A5R, 16K)
650 sheets (12" x 18", 11" x 17", 8-1/2" x 14",
8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, A3W, A3, B4,
A4R, B5R, 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (8-1/2" x 11", A4, B5,
16K)
50 sets or 650 sheets (11" x 17", 8-1/2" x 14",
8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",
8-1/2" x 11"R, A3, B4, A4R, 8K)
Lower tray
Non-stapling*3:
2450 sheets (8-1/2" x 11", A4, B5, 16K)
1700 sheets (5-1/2" x 8-1/2"R, A5R)
650 sheets (12" x 18", 11" x 17", 8-1/2" x 14",
8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",
8-1/2" x 11"R, 7-1/4" x 10-1/2", A3W, A3, B4,
A4R, B5R, 8K, 16KR)
Stapling*4:
100 sets or 1550 sheets (8-1/2" x 11", A4, B5,
16K)
50 sets or 650 sheets (11" x 17", 8-1/2" x 14",
8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",
8-1/2" x 11"R, A3, B4, A4R, 8K)
Tray
capacity*2
Power supply
Supplied from the machine
Dimensions
25-25/64" (W) x 25-25/64" (D) x 43-19/64" (H) (645 mm (W) x 645 mm (D) x 1100 mm (H))
(When tray is extended)
Weight
Approx. 99.3 lbs. (45 kg)
Stapler section
Allowed paper sizes for
stapling
11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
A3, B4, A4, A4R, B5, 8K, 16K
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two staples.)
Maximum number of
sheets for stapling*5
50 sheets (8-1/2" x 11", A4, B5, 16K
30 sheets (11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11" A3,
B4, A4R, 8K)
(30 sheets when the sheets are the same width but different lengths.)
*1 Paper pass unit and stand/1x500 sheet paper drawer or stand/2x500 sheet paper drawer are required to connect the finisher (large
stacker) to the machine.
*2 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of
paper, and the storage conditions of the paper.
*3 Up to 100 sheets of non-standard size paper, envelopes, and transparency film (8-1/2" x 11"(A4)) can be loaded.
*4 The maximum number of sheets for stapling assumes a paper weight of 24 lbs. (90 g/m2) and includes two cover sheets of 28 lbs.
bond to 110 lbs. index (106 g/m2 to 209 g/m2).
Note:
Special media such as transparency film and label sheets cannot be stapled or punched.
14
mxm503_us_saf.fm
15 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Saddle stitch finisher specifications*1
Model
MX-FN10
Paper sizes
12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, envelopes, A3W, A3, B4, A4, A4R, B5, B5R, A5R, 8K, 16K, 16KR
Paper weight
Thin paper (15 lbs. to 16 lbs. (56 g/m2 to 59 g/m2)) plain paper (16 lbs. to 28 lbs. (60 g/m2 to 105 g/m2)) heavy
paper (28 lbs. bond to 110 lbs. index (106 g/m2 to 209 g/m2)), envelopes (20 lbs. to 24 lbs. (75 g/m2 to 90 g/m2))
Modes
Non-staple, staple, saddle stitch, half fold (Output is folded in half one sheet at a time.)
Allowed paper sizes for offset
11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
7-1/4" x 10-1/2"R, A3, A4, A4R, B4, B5, B5R, 8K, 16K, 16KR
Offset distance
1-3/16" (30 mm)
Tray capacity*2
Non-stapling*3:
1000 sheets*4 (8-1/2" x 11", 8-1/2" x 11"R,
7-1/4" x 10-1/2"R, A4, A4R, B5, B5R, 16K, 16KR)
500 sheets*5 (12" x 18", 11" x 17", 8-1/2" x 14",
8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",
5-1/2" x 8-1/2"R, A3W, A3, B4, A5R, 8K)
Power supply
Supplied from the machine
Dimensions
25-53/64" (W) x 24-27/32" (D) x 38-57/64" (H) (656 mm (W) x 631 mm (D) x 988 mm (H))
(When tray is extended)
Weight
Approx. 88.2 lbs. (40 kg)
Stapling*6:
50 sets or 1000 sheets*4 (8-1/2" x 11",
8-1/2" x 11"R, A4, A4R, B5, B5R, 16K, 16KR)
50 sets or 500 sheets*5 (11" x 17", 8-1/2" x 14",
8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13",
A3, B4, 8K)
Stapler section
Allowed paper sizes for
stapling
11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
A3, B4, A4, A4R, B5, B5R, 8K, 16K, 16KR
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two staples.)
Maximum number of
sheets for stapling*6
50 sheets (8-1/2" x 11", 8-1/2" x 11"R, A4, A4R, B5, B5R, 16K, 16KR)
25 sheets (11" x 17", 8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", A3, B4, 8K)
(25 sheets when the sheets are the same width but different lengths.)
Saddle stitch section
Stapling method
Fold in half and staple in two places on centerline
Folding position
Fold at centerline (can be adjusted with [Saddle Stitch Position Adjust] in the System Settings)
Allowed paper sizes for
saddle stitch stapling
11" x 17", 8-1/2" x 14", 8-1/2" x 11"R, A3, B4, A4R, 8K, 16KR
Allowed paper weights for 15 lbs. bond to 110 lbs. index (56 g/m2 to 209 g/m2)*7
saddle stitch stapling
Maximum: 15 sheets (21 lbs. (80 g/m2) x 14 sheets + 110 lbs. index (209 g/m2) x 1 sheet) / 10 sets
Number sheets for saddle
stitch stapling / Number of sets (11 to 15 sheets), 15 sets (6 to 10 sheets), 20 sets (1 to 5 sheets)
*1 Paper pass unit and stand/1x500 sheet paper drawer or stand/2x500 sheet paper drawer are required to connect the saddle stitch
finisher to the machine.
*2 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of
paper, and the storage conditions of the paper.
*3 Up to 30 envelopes can be output.
*4 The height of the sheets must not exceed 6-57/64" (175 mm).
*5 The height of the sheets must not exceed 3-45/64" (94 mm).
*6 The maximum number of sheets for stapling assumes a paper weight of 24 lbs. (90 g/m2) and includes two cover sheets of 28 lbs.
bond to 110 lbs. index (106 g/m2 to 209 g/m2).
*7 Allowed paper weights for saddle stitch stapling of plain paper include heavy paper (28 lbs. bond to 110 lbs. index (106 g/m2 to
209 g/m2)).
Note:
Special media such as transparency film and label sheets cannot be stapled or punched.
15
mxm503_us_saf.fm
16 ページ
2009年5月15日 金曜日 午後3時20分
SPECIFICATIONS
Punch module specifications (for finisher)
Model
MX-PNX1B
Hole punching
3 holes or 2 holes
Allowed paper sizes for
punching
3 holes:
11" x 17", 8-1/2" x 11", A3, A4
2 holes:
8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11"R, 7-1/4" x 10-1/2"
Punchable paper weights 15 lbs. to 34 lbs. (56 g/m2 to 128 g/m2)
Power supply
Supplied from finisher
Dimensions
4-9/64" (W) x 20-25/64" (D) x 6-45/64" (H) (105 mm (W) x 518 mm (D) x 170 mm (H))
Weight
Approx. 7.7 lbs. (3.5 kg)
Punch module specifications (for finisher (large stacker))
Model
MX-PNX6B
Hole punching
3 holes or 2 holes
Allowed paper sizes for
punching
3 holes:
11" x 17", 8-1/2" x 11", A3, A4
2 holes:
8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11"R, 7-1/4" x 10-1/2"
Punchable paper weights 15 lbs. to 34 lbs. (56 g/m2 to 128 g/m2)
Power supply
Supplied from finisher (large stacker)
Dimensions
4-17/32" (W) x 23-5/8" (D) x 39-11/64" (H) (115 mm (W) x 600 mm (D) x 995 mm (H))
Weight
Approx. 17.7 lbs. (8 kg)
Punch module specifications (for saddle stitch finisher)
Model
MX-PNX5B
Hole punching
3 holes or 2 holes
Allowed paper sizes for
punching
3 holes:
11" x 17", 8-1/2" x 11", A3, A4
2 holes:
8-1/2" x 14", 8-1/2" x 13-1/2", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11"R, 7-1/4" x 10-1/2"
Punchable paper weights 15 lbs. to 34 lbs. (56 g/m2 to 128 g/m2)
Power supply
Supplied from saddle stitch finisher
Dimensions
4-13/16" (W) x 23-25/32" (D) x 9-49/64" (H) (122 mm (W) x 604 mm (D) x 248 mm (H))
Weight
Approx. 7.7 lbs. (3.5 kg)
Note:
Special media such as transparency film and label sheets cannot be stapled or punched.
16
mxm503_us_saf.fm
17 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Printer specifications
Type
Built-in
Continuous printing speed
Same as continuous copying speed (When printing same document continuously on 8-1/2" x 11"
(A4) plain paper in non-offset mode, excluding processing time.)
Printing resolution
600 x 600 dpi / 1200 x 1200 dpi
Printer driver type
PCL5e, PCL6, PostScript 3 compatible*1, XPS*4
Supported protocols
TCP/IP, IPX/SPX, NetBEUI, EtherTalk*1
Supported client PC
operating systems
See "VERIFYING SYSTEM REQUIREMENTS" in the Software Setup Guide.
Fonts
PCL5e, PCL6
80 European fonts, 28 barcode fonts*2, 1 bitmap font
PostScript 3 compatible*1
136 European fonts
Interface port
LAN connectivity: 10Base-T / 100Base-TX / 1000Base-T
USB connectivity: Supports USB 2.0 (Hi speed)*3
Memory
Standard system memory: 1 GB
Expansion memory: 1 GB*5
Print area
Entire page excluding margin of 11/64" (4.2 mm) at each edge. The actual print area may vary
depending on the printer driver and the software application.
*1
*2
*3
*4
*5
When the PS3 expansion kit is installed and the machine is used as a PostScript printer.
Barcode font kit is required.
Supported operating systems are Windows 2000 / XP / Vista / Server 2008.
When the XPS expansion kit is installed.
To install the XPS expansion kit, an expansion memory board is required.
17
mxm503_us_saf.fm
18 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Network scanner / Internet Fax*1 specifications
Type
Built-in
100 x 100, 200 x 200, 300 x 300, 400 x 400, 600 x 600
Scanning resolution (dpi) Internet Fax: 200 x 100, 200 x 200, 200 x 400, 400 x 400, 600 x 600 (200 x 100, 200 x 200 when file
type is TIFF-S) Halftone can be selected for resolutions other than 200 x 100 dpi.
Scanning speed
MX-M363N/MX-M453N/MX-M503N:
Color (8-1/2" x 11" / A4) One-sided: 70 pages/min. (200 x 200 dpi),
Two-sided: 70 pages/min. (200 x 200 dpi)
Black and white (8-1/2" x 11" / A4) One-sided: 70 pages/min. (200 x 200 dpi),
Two-sided: 70 pages/min. (200 x 200 dpi)
MX-M283N:
Color (8-1/2" x 11" / A4) One-sided: 50 pages/min. (200 x 200 dpi),
Two-sided: 20 pages/min. (200 x 200 dpi)
Black and white (8-1/2" x 11" / A4) One-sided: 50 pages/min. (200 x 200 dpi),
Two-sided: 20 pages/min. (200 x 200 dpi)
Interface port
LAN connectivity: 10Base-T / 100Base-TX / 1000Base-T
Supported protocols
TCP/IP (IPv4)
File formats
Remarks
Color
(including grayscale)
File types: TIFF, JPEG, PDF, Encrypted PDF, XPS, Compact
PDF*2
Compression ratio: High / Medium / Low
Black and white
File types: TIFF, PDF, Encrypted PDF, XPS
Compression modes: None / Medium (G3) / High (G4)
Internet Fax
(black and white only)
File types: TIFF-FX (TIFF-F, TIFF-S)
Compression modes: Medium (G3) / High (G4)
Number of one-touch keys for
storing destinations*3
Maximum number of keys: 1000
Number of destinations that can be Maximum number of destinations in one group (1 key): 500
stored in a group (1 key)*3
Scan destinations
Scan to E-mail / Scan to FTP / Scan to Desktop / Scan to
Network Folder
*1 Internet fax expansion kit is required.
*2 Enhanced compression kit is required.
*3 Total number of all destinations (Scan to E-mail, Scan to FTP, Scan to Desktop, Scan to Network folder, Internet Fax, Fax, and
Group)
18
mxm503_us_saf.fm
19 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Pull scan function (TWAIN) specifications
Supported protocol
TCP/IP (IPv4)
Supported client PC
operating systems
Windows 98 / Me / 2000 / XP / Server 2003 / Vista/ Server 2008
Color modes
Full Color, Grayscale, Mono Diffusion, Mono 2 gradation
Resolution settings
75 dpi, 100 dpi, 150 dpi, 200 dpi, 300 dpi, 400 dpi, 600 dpi
(The resolution can be specified by entering a numerical value from 50 to 9600 dpi. However, when
a high resolution is specified, it is necessary to reduce the scanning area.)
Scanning area
Maximum: 11" x 17" (A3)
19
mxm503_us_saf.fm
20 ページ
2009年5月14日 木曜日 午後8時25分
SPECIFICATIONS
Facsimile specifications
Model
MX-FXX2
Applicable telephone line Public switched telephone network, PBX
Scanning resolution
(supports ITU-T
standards)
8 x 3.85 lines/mm (Standard), 8 x 7.7 lines/mm (Fine, Fine-Halftone), 8 x 15.4 lines/mm (Super Fine,
Super Fine - Halftone), 16 x 15.4 lines/mm (Ultra Fine, Ultra Fine - Halftone)
Transmission speed
33.6 kbps down to 2.4 kbps Automatic fallback
Compression method
MH / MR / MMR / JBIG
Transmission modes
Super G3, G3 (the machine can only send faxes to and receive faxes from machines that support G3
or Super G3)
Input document size
Inch sizes: 11" x 17", 8-1/2" x 14", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
5-1/2" x 8-1/2"
AB sizes: A3, B4, A4, A4R, B5, B5R, A5, 216 mm x 340 mm, 216 mm x 343 mm
Long originals (max. width 11-45/64" (297 mm) x max. length 39-23/64" (1000 mm) can be
transmitted using the automatic document feeder. Scanning one side is possible.)
Paper sizes
11" x 17", 8-1/2" x 14", 8-1/2" x 13-2/5", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 5-1/2" x 8-1/2"R (A3,
B4, A4, A4R, B5, B5R, A5R)
Transmission time *1
Approx. 2 seconds (Super G3 mode/33.6 kbps, JBIG)
Approx. 6 seconds (G3 ECM mode/14.4 kbps)
Power supply
Supplied from the machine
Dimensions
7-9/16" (W) x 2-3/64" (D) x 8-15/32" (H) (192 mm (W) x 52 mm (D) x 215 mm (H))
Weight
Approx. 2.2 lbs. (1.0 kg)
Extension telephone connection
Possible (1 telephone)
Number of one-touch keys for storing
destinations*2
Maximum number of keys: 1000
Number of destinations that can be stored in a Maximum number of destinations in one group
(1 key): 500
group (1 key)*2
Remarks
Timer transmission
Yes
Program function
Yes (48 programs)
F-code transmission
Supported (SUB/SEP (sub-address) and SID/PWD
(passcode) signals can be transmitted / received)
Image memory
8 MB standard
*1 Transmission speed is for an 8-1/2" x 11" or A4 document with approximately 700 characters at standard resolution (8 x 3.85
lines/mm) sent in high speed mode (33.6 kbps (JBIG) or 14.4 kbps). This is only the time required to transmit the image
information; the time required to send protocol signals is not included. Actual transmission times will vary depending on the
contents of the document, the receiving machine type, and telephone line conditions.
*2 Total number of all destinations (Scan to E-mail, Scan to FTP, Scan to Desktop, Scan to Network folder, Internet Fax, Fax and
Group)
20
mxm503_us_saf.fm
21 ページ
2009年5月14日 木曜日 午後8時25分
✂
Administrator
Name:
Contact at:
Information that the administrator of the machine requires is printed on
the back of this page.
(Separate this page from the manual and keep it in a safe place. In
addition, fill in the name of the administrator and the administrator's
contact information in the left hand margin.)
21
mxm503_us_saf.fm
22 ページ
2009年5月14日 木曜日 午後8時25分
TO THE ADMINISTRATOR OF THE
MACHINE
(Separate this page from the manual and keep it in a safe place.)
Factory default passwords
When accessing the system settings, the administrator password is required to log in with administrator
rights. The system settings can be configured in the Web pages as well as on the operation panel. To
access the system settings using the Web pages, a password is also required.
Factory default administrator password
Factory default setting: admin
Store a new administrator password as soon as the machine is installed.
Once the administrator password has been changed, the new password is required to restore the factory
default password. Take care to remember the new password.
There are two factory default accounts: "Administrator" and "User". A person who logs in as an
"Administrator" can configure all settings in the Web pages. In addition, an administrator can restrict access
to other settings by enabling "User" accounts.
The factory default passwords are shown below.
Factory default account
Factory default password
User
users
users
Administrator
admin
admin
Forwarding all transmitted and received data to the administrator
(document administration function)
This function is used to forward all data transmitted and received by the machine to a specified destination
(Scan to E-mail address, Scan to FTP destination, Scan to Network Folder destination, or Scan to Desktop
destination).
This function can be used by the administrator of the machine to archive all transmitted and received data.
To configure the document administration settings, click [Application Settings] and then [Document
Administration Function] in the Web page menu. (Administrator rights are required.)
Note:
• The format, exposure, and resolution settings of transmitted and received data remain in effect when the data is
forwarded.
• When forwarding is enabled for data sent in fax mode,
• The [Direct TX] key does not appear in the touch panel.
• Quick online transmission and dialing using the speaker cannot be used.
22
✂
Factory default passwords (Web pages)
mxm503_us_saf.fm
23 ページ
2009年5月14日 木曜日 午後8時25分
TO THE ADMINISTRATOR OF THE MACHINE
For the users of the fax function
ABOUT THE TELEPHONE CONSUMER PROTECTION ACT OF 1991
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device,
including FAX machines, to send any message unless such message clearly contains in a margin at the top or bottom of each
transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other
entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or
individual.
(The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance
transmission charges.)
In order to program this information into your FAX machine, you should complete the following steps:
See "Own Name and Destination Set" on page 7-78 of Operation Guide.
Important safety instructions
• If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may
cause harm to the telephone network.
• The AC power outlet shall be installed near the equipment and shall be easily accessible.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
• Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from
lightning.
• Do not use a telephone to report a gas leak in the vicinity of the leak.
• Do not install or use the machine near water, or when you are wet. Take care not to spill any liquids on the machine.
• Save these instructions.
23
mxm503_us_saf.fm
24 ページ
2009年5月14日 木曜日 午後8時25分
TO THE ADMINISTRATOR OF THE MACHINE
FCC Notice to users:
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA.
On this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone company.
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0).
To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone
company.
For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format
US:AAAEQ##TXXXX.
The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).
For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, your telephone company may disconnect your service temporarily. If
possible, They will notify you in advance. If advance notice is not practical, you will be notified as soon as possible. You will also be
advised of your right to file a compliant with the FCC.
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of
your equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications
to maintain uninterrupted service. If the equipment is causing harm to the telephone network, your telephone company may ask you
to disconnect the equipment until the problem is resolved.
If you have any questions or problems which cannot be solved by reading this manual, please contact.
Sharp Electronics Corporation
1 Sharp Plaza,
Mahwah, NJ 07495
Telephone: 1-800-BE-SHARP
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC
Part 68 rules and requirements adopted by the ACTA.
A compliant telephone cord and modular plug is provided with this product.
It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.
This equipment connects to the telephone network through a standard USOC RJ-11C network interface jack.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not
disable your alarm equipment.
If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
This equipment may not be used on coin service provided by the telephone company.
Connection to party lines service is subject to state tariffs.
Contact your state's public utility commission, public service commission or corporation commission for more information.
24
mxm503_us_saf.fm
25 ページ
2009年5月14日 木曜日 午後8時25分
TO THE ADMINISTRATOR OF THE MACHINE
NOTICE for users in the USA
BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE
WARRANTY THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to
assure you, the end-user, of warranty protection, Sharp extends a limited warranty to
each of its authorized dealers and, in turn, requires each of its authorized dealers to
extend its own warranty to you on terms that are no less favorable than those given
to the dealer by Sharp. You should be aware, however, that Sharp does not itself
extend any warranties, either express or implied, directly to you, the end-user, and no
one is authorized to make any representations or warranties on behalf of Sharp.
Specifically, SHARP DOES NOT EXTEND TO YOU, THE END-USER, ANY
EXPRESS WARRANTY OR ANY IMPLIED WARRANTY OF MERCHANTABILITY,
FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR PURPOSE IN
CONNECTION WITH THE HARDWARE, SOFTWARE OR FIRMWARE EMBODIED
IN, OR USED IN CONJUNCTION WITH THIS PRODUCT. Sharp is not responsible
for any damages or loss, either direct, incidental or consequential, which you, the
end-user, may experience as a result of your purchase or use of the hardware,
software or firmware embodied in or used in conjunction with this Product. Your sole
remedy, in the event that you encounter any difficulties with this Product, is against
the authorized dealer from which you purchased the Product.
MX-M283N
MX-M363N
MX-M453N
MX-M503N
Digital Multifunctional System
Digital Multifunctional System
Digital Multifunctional System
Digital Multifunctional System
In the event that this authorized dealer does not honor its warranty commitments,
please contact the General Manager, Business Products Group, Sharp Electronics
Corporation, 1 Sharp Plaza, Mahwah, NJ 07495-1163, so that Sharp can try to help
assure complete satisfaction of all the warranty rights to which you are entitled from
the authorized dealer.
25
mxm503_us_saf.fm
26 ページ
2009年5月14日 木曜日 午後8時25分
TO THE ADMINISTRATOR OF THE MACHINE
NOTICE FOR USERS IN
CANADA
"NOTICE : This product meets the applicable Industry
Canada technical specifications."
"NOTICE : The Ringer Equivalence Number is an
indication of the maximum number of devices allowed to
be connected to a telephone interface. The termination
on an interface may consist of any combination of
devices subject only to the requirement that the sum of
the RENs of all the devices does not exceed five."
The REN of this equipment is indicated on the facsimile
expansion kit.
AVIS POUR NOS
UTILISATEURS AU CANADA
AVIS : Le présent matériel est conforme aux
spécifications techniques applicables d'Industrie
Canada.
Remarque : L'indice d'équivalence de la sonnerie (IES)
sert à indiquer le nombre maximal de terminaux qui
peuvent être raccordés à une interface téléphonique. La
terminaison d'une interface peut consister en une
combinaison quelconque de dispositifs, à la seule
condition que la somme d'indices d'équivalence de la
sonnerie de tous les dispositifs n'excède pas 5.
L'indice d'équivalence de la sonnerie (IES) de cet
équipement est indiqué sur le kit d'extension
télécopieur.
Sharp Electronics of Canada Ltd.
335 Britannia Road East,
Mississauga, Ontario, L4Z 1W9
Canada
26
mxm503_us_saf.fm
27 ページ
2009年5月14日 木曜日 午後8時25分
TO THE ADMINISTRATOR OF THE MACHINE
Trademark acknowledgments
The following trademarks and registered trademarks are used in conjunction with the machine and its peripheral devices and
accessories.
• Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, Windows® XP, Windows Server®
2003, Windows Vista®, Windows Server® 2008 and Internet Explorer® are registered trademarks or trademarks of Microsoft
Corporation in the U.S.A. and other countries.
• PostScript is a registered trademark of Adobe Systems Incorporated.
• Adobe and Flash are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other
countries.
• Adobe, the Adobe logo, Acrobat, the Adobe PDF logo, and Reader are registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and other countries.
• Macintosh, Mac OS, AppleTalk, EtherTalk and LaserWriter are trademarks of Apple Inc., registered in the U.S. and other countries.
• Netscape Navigator is a trademark of Netscape Communications Corporation.
• Mozilla® and Firefox® are registered trademarks or trademarks of the Mozilla Foundation in the U.S.A. and other countries.
• PCL is a registered trademark of the Hewlett-Packard Company.
• IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation.
• Sharpdesk is a trademark of Sharp Corporation.
• Sharp OSA is a trademark of Sharp Corporation.
• RealVNC is a trademark of RealVNC Limited.
• All other trademarks and copyrights are the property of their respective owners.
Candid and Taffy are trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may
be registered in certain jurisdictions. CG Omega, CG Times, Garamond Antiqua, Garamond Halbfett, Garamond Kursiv,
Garamond and Halbfett Kursiv are trademarks of Monotype Imaging, Inc. and may be registered in certain jurisdictions. Albertus,
Arial, Coronet, Gill Sans, Joanna and Times New Roman are trademarks of The Monotype Corporation registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions. Avant Garde, ITC Bookman, Lubalin Graph,
Mona Lisa, Zapf Chancery and Zapf Dingbats are trademarks of International Typeface Corporation registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions. Clarendon, Eurostile, Helvetica, Optima,
Palatino, Stempel Garamond, Times and Univers are trademarks of Heidelberger Druckmaschinen AG, which may be registered
in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned subsidiary of Heidelberger
Druckmaschinen AG. Apple Chancery, Chicago, Geneva, Monaco and New York are trademarks of Apple Computer Inc. and may
be registered in certain jurisdictions. HGGothicB, HGMinchoL, HGPGothicB and HGPMinchoL are trademarks of Ricoh
Company, Ltd. and may be registered in some jurisdictions. Wingdings is a registered trademark of Microsoft Corporation in the
United States and other countries. Marigold and Oxford are trademarks of Arthur Baker and may be registered in some
jurisdictions. Antique Olive is a trademark of Marcel Olive and may be registered in certain jurisdictions. Hoefler Text is a
trademark of Johnathan Hoefler and may be registered in some jurisdictions. ITC is a trademark of International Typeface
Corporation registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions. Agfa is a
trademark of the Agfa-Gevaert Group and may be registered in certain jurisdictions. Intellifont, MicroType and UFST are
trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may be registered in
certain jurisdictions. Macintosh and TrueType are trademarks of Apple Computer Inc. registered in the United States Patent and
Trademark Office and other countries. PostScript is a trademark of Adobe Systems Incorporated and may be registered in some
jurisdictions. HP, PCL, FontSmart and LaserJet are trademarks of Hewlett-Packard Company and may be registered in some
jurisdictions. The Type 1 processor resident in Monotype Imaging's UFST product is under license from Electronics For Imaging,
Inc. All other trademarks are the property of their respective owners.
27
mxm503_us_saf.fm
28 ページ
2009年5月14日 木曜日 午後8時25分
mxm503_us_saf.fm
29 ページ
2009年5月14日 木曜日 午後8時25分
mxm503_us_saf.fm
30 ページ
2009年5月14日 木曜日 午後8時25分
MX-M283N/MX-M363N/MX-M453N/MX-M503N
Safety Guide
SHARP ELECTRONICS CORPORATION
1 Sharp Plaza, Mahwah, New Jersey 07495-1163.
www.sharpusa.com
SHARP ELECTRONICS OF CANADA LTD.
335 Britannia Road East, Mississauga, Ontario, L4Z 1W9
This manual has been printed using a vegetable-based soy oil ink
to help protect the environment.
PRINTED IN CHINA
2009E
KS1
TINSE4457FCZZ
Download PDF

advertising