Sharp | XG-NV7XU | Owner's Manual | Sharp XG-NV7XU Owner's Manual

Important
Information
OPERATION MANUAL
Setup & Connections
Operation
Useful Features
MODEL
DIGITAL MULTIMEDIA
PROJECTOR
Maintenance &
Troubleshooting
XG-NV7XU
Appendix
Before using the projector, please read this operation manual carefully.
Important
Information
OPERATION MANUAL
ENGLISH
IMPORTANT
For your assistance in reporting the loss or theft of your
projector, please record the Serial Number located on
the bottom of the projector and retain this information.
Before recycling the packaging, please be sure that
you have checked the contents of the carton thoroughly
against the list of “Supplied Accessories” on page 10.
Model No.: XG-NV7XU
Serial No.:
There are two important reasons for prompt warranty registration of your new SHARP Projector, using
the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service and labor
warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection, modification, or
recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE
READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.
U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially
careful that children do not stare directly into the beam of light.
WARNING: To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER.
NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude
to constitute a risk or electric shock to
persons.
The exclamation point within a triangle is
intended to alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not
expressly approved by the manufacturer could void the user’s authority to operate this equipment.
U.S.A. ONLY
INFORMATION
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the operation manual,
may cause harmful interference to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to correct the interference at his own
expense.
U.S.A. ONLY
The enclosed computer cable must be used with the device. The cable is provided to ensure that the device
complies with FCC Class A verification.
U.S.A. ONLY
E-1
IMPORTANT SAFEGUARDS
1. Read Instructions
All the safety and operating instructions should be read
before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained
for future reference.
3. Heed Warnings
All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product
manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water–for example, near a
bathtub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to
the product. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with
the product. Any mounting of the product should follow
the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9. Transportation
A product and cart combination
should be moved with care. Quick
stops, excessive force, and
uneven surfaces may cause the
product and cart combination to
overturn.
10. Ventilation
Slots and openings in the cabinet are provided for
ventilation to ensure reliable operation of the product and
to protect it from overheating. The openings should never
be covered or blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should
not be placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of
power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult
your product dealer or local power company. For products
intended to operate from battery power, or other sources,
refer to the operating instructions.
12. Grounding or Polarization
This product is equipped with a three-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will
only fit into a grounding-type power outlet. This is a safety
feature. If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type
plug.
13. Power-Cord Protection
Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them, paying particular attention to cords at
plugs, convenience receptacles, and the point where they
exit from the product.
14. Lightning
For added protection for this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage
to the product due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire
or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
17. Servicing
Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service
personnel.
18. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:
a. If the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions, as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to normal
operation.
e. If the product has been dropped or damaged in any
way.
f. If the product exhibits a distinct change in
performance, this indicates a need for service.
19. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or other hazards.
20. Safety Check
Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating
condition.
21. Wall or Ceiling Mounting
This product should be mounted to a wall or ceiling only
as recommended by the manufacturer.
22. Heat
This product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
Important
Information
Electrical energy can perform many useful functions. This product has been engineered and manufactured to ensure your
personal safety. But IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order not to
defeat the safeguards incorporated into this Projector, observe the following basic rules for its installation, use and servicing.
For your own protection and reliable usage of your projector, please be sure to read these “IMPORTANT SAFEGUARDS”
carefully before use.
E-2
Outstanding Features
Important
Information
1. DIRECT DIGITAL COMPUTER INPUT (PanelLink™)
Signals remain digital from the source device to the projector thus resulting in sharper, clearer, noiseless and adjustment-free
computer images.
2. ADVANCED COMPATIBILITY WITH HIGH-END WORKSTATIONS
AND PCS
Compatible with up to 200 Hz vertical refresh rate, Sync on Green and Composite Sync signals
for use with a wide variety of high-end PCs and Workstations. (Page 11)
X
L
H
3. FOR USE WITH DTV*/HDTV
Allows projection of DTV images and 16:9 wide-screen images when connected to a DTV decoder
or similar video systems. (Page 13)
4. COMPONENT VIDEO COMPATIBILITY (VIA RGB)
Equipped with terminals for connection to a DTV decoder, DVD player and similar video systems for higher quality images.
(Page 13)
5. ADVANCED VIDEO CIRCUITRY
Provides high quality video images with minimal noise for more impressive presentations.
6. DIGITAL KEYSTONE CORRECTION
Digitally adjusts an image that is projected at an angle while maintaining image quality and
brightness. (Page 19)
7. EASY-TO-USE GRAPHICAL USER INTERFACE (GUI)
A multi-color, icon based menu system allows for simple image adjustments. (Page 23)
8. USER-FRIENDLY DESIGN
The two-color design along with an intuitive Graphical User Interface (GUI) makes this projector
very easy to set up and adjust.
9. WIRELESS PRESENTATIONS WITH IrCOM
The IrCOM function allows for wireless transmission of digital images via infrared
communication from a PC or digital camera. (Page 25)
10. AUTO SYNC TECHNOLOGY FOR AUTOMATIC IMAGE
PERFECTION
Automatically makes any necessary adjustments for perfectly synced computer images.
(Page 29)
11. INTELLIGENT COMPRESSION AND EXPANSION
By using intelligent resizing technology, this projector can display higher and lower resolution images in detail without
compromising quality. (Page 36)
12. XGA RESOLUTION FOR HIGH RESOLUTION PRESENTATIONS
With XGA (1,024 768) resolution, this projector can display very detailed presentation information.
13. UXGA COMPATIBLE
UXGA (1,600 1,200) resolution images are intelligently resized to 1,024 768 for full-screen or default presentations.
14. CUSTOMIZABLE STARTUP SCREEN
Allows you to load a custom startup image (i.e. your company logo) to be displayed while the projector is warming up.
(Page 42)
15. BUILT-IN PRESENTATION TOOLS
A variety of helpful presentation utilities are incorporated to enhance presentations. These include “Stamp” functions, “Break
Timer”, and “Digital Enlarge”. (Page 44)
16. QUIET OPERATION
The quiet fan operation allows the audience to concentrate on the presentation without the distraction of fan noise.
*DTV is the umbrella term used to describe the new digital television system in the united states.
E-3
Contents
2
3
4
5
6
6
7
Setup & Connections
Supplied Accessories …………………………… 10
Connecting the Projector ……………………… 11
Freeze Function ……………………………………
Digital Image Magnification (ENLARGE) ………
Gamma Correction ………………………………
Selecting the Picture Display Mode ……………
Black Screen Function ……………………………
On-screen Display Override Function …………
Automatic Power Shutoff Function ……………
I/P Conversion ……………………………………
Checking the Lamp Usage Time ………………
Selecting the Signal Type ………………………
Checking the Input Signal ………………………
Setting a Background Image ……………………
Selecting a Startup Image ………………………
Reverse/Invert Image Function …………………
Using the Presentation Tools ……………………
Status Function ……………………………………
33
34
35
36
37
37
38
39
39
40
40
41
42
43
44
45
Setup & Connections
IMPORTANT SAFEGUARDS ……………………
Outstanding Features ……………………………
Contents ……………………………………………
Usage Guidelines …………………………………
How to Access the PDF Operation Manuals
(for Windows and Macintosh) ………………
For SHARP Assistance (U.S.A. only) …………
Part Names …………………………………………
Useful Features
Important
Information
Important Information
Operation
16
18
21
23
25
26
Lamp/Maintenance Indicators …………………
Replacing the Projection Lamp …………………
Using the Kensington Lock ……………………
Troubleshooting ……………………………………
47
48
49
49
Appendix
Transporting the Projector ………………………
Connection Pin Assignments ……………………
RS-232C Port Specifications ……………………
Input Signals (Recommended Timing) …………
Specifications ………………………………………
Dimensions …………………………………………
Guide to Effective Presentations ………………
Glossary ……………………………………………
Index …………………………………………………
51
52
53
55
57
58
59
63
64
Useful Features
26
27
28
29
30
30
31
32
Maintenance & Troubleshooting
Operation
Basic Operations …………………………………
Setting up the Screen ……………………………
Operating the Wireless Mouse from the
Remote Control ………………………………
Using the GUI (Graphical User Interface)
Menu Screens …………………………………
Using IrCOM for Wireless Presentations ………
Selecting the On-screen Display Language …
Selecting the Video Input System Mode
(VIDEO mode only) ……………………………
Picture Adjustments ………………………………
Audio Adjustments ………………………………
Computer Image Adjustments …………………
Auto Sync Adjustment …………………………
Auto Sync Display Function ……………………
Saving and Selecting Adjustment Settings …
Special Mode Adjustment ……………………
Maintenance &
Troubleshooting
Appendix
E-4
Important
Information
Usage Guidelines
CAUTION
LASER RADIATIONDO NOT STARE INTO BEAM
WAVE LENGTH : 650nm
MAX. OUTPUT : 1mW
CLASS II LASER PRODUCT
"COMPLIES WITH 21 CFR SUBCHAPTER J"
SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07430
U.S.A. ONLY
TEL : 1-800-BE-SHARP
REMOTE CONTROL
MODEL NO. : RRMCG1530CESA
DC3V (1.5VX2PCS.)
MADE IN CHINA
FABRIQUÉ AU CHINE
AVOID EXPOSURE-LASER
RADIATION IS EMITTED
FROM THIS APERTURE.
Cautions Concerning the Laser Pointer
The laser pointer on the remote control emits a laser beam from the laser
pointer window. This is a Class II laser which may impair your sight if directed
into the eyes. The three marks shown on the left are caution labels for the
laser beam.
• Do not look into the laser pointer window or shine the laser beam on yourself or
others. (The laser beam used in this product is harmless when directed onto
the skin. However, be careful not to project the beam directly into the eyes.)
• Always use the laser pointer at temperatures between 41°F and 95°F (5°C
and 35°C).
• Use of controls or adjustments, or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
Laser pointer
window
Cautions Concerning the Setup of the Projector
95˚F
(35˚C)
41˚F
(5˚C)
For minimal servicing and to maintain high image quality, SHARP recommends
that this projector be installed in an area free from humidity, dust and cigarette
smoke. When the projector is subjected to these environments, the lens and
filter must be cleaned more often. Periodically the filter should be replaced
and the projector should be cleaned internally. As long as the projector is
properly maintained in this manner, use in these environments will not reduce
the overall operation life. Please note that all internal cleaning must be
performed by an Authorized Sharp Industrial LCD Products Dealer or Service
Center.
Notes on Operation
• The two marks shown on the left are caution labels for parts of the projector
that emit intense heat during operation.
• The exhaust vents, the lamp cage cover and adjacent areas may be extremely
hot during projector operation. To prevent injury, do not touch these areas until
they have sufficiently cooled.
• Allow at least 4 inches (10 cm) of space between the cooling fan (exhaust
vent) and the nearest wall or obstruction.
• If the cooling fan becomes obstructed, a protection device will automatically
turn off the projector lamp. This does not indicate a malfunction. Remove the
projector power cord from the wall outlet and wait at least 10 minutes. Then
turn on the power by plugging the power cord back in. This will return the
projector to the normal operating condition.
Temperature Monitor Function
If the projector starts to overheat due to setup problems or a dirty air filter, “TEMP.”
and “ ” will flash in the lower-left corner of the picture. If the temperature continues
to rise, the lamp will turn off, the TEMPERATURE WARNING indicator on the
projector will flash, and after a 90-second cooling-off period the power will shut
off. Refer to “Lamp/Maintenance Indicators” on page 47, for details.
• The cooling fan regulates the internal temperature, and its performance is
automatically controlled. The sound of the fan may change during projector
operation due to changes in the fan speed.
E-5
How to Access the PDF Operation Manuals (for Windows and Macintosh)
Important
Information
PDF operation manuals in several languages are included in the CD-ROM. To utilize these manuals, you need to
install Adobe Acrobat Reader on your PC (Windows or Macintosh). If you have not installed Acrobat Reader yet,
you can download it from the Internet (http://www.adobe.com) or install it from the CD-ROM.
To Install Acrobat Reader (English version) from the CD-ROM
For Windows:
1
2
3
4
5
6
7
Insert the CD-ROM in the CD-ROM drive.
Double click on the “My Computer” icon.
Double click on the “CD-ROM” drive.
Double click on the “manuals” folder.
Double click on the “acrobat” folder.
Double click on the “windows” folder.
Double click on the installation program and follow
the instructions on the screen.
For Macintosh:
1
2
3
4
5
6
Insert the CD-ROM in the CD-ROM drive.
Double click on the “CD-ROM” icon.
Double click on the “manuals” folder.
Double click on the “acrobat” folder.
Double click on the “mac” folder.
Double click on the installation program and follow
the instructions on the screen.
For other operating systems:
Please download Acrobat Reader from the Internet (http://www.adobe.com).
For other languages:
If you prefer using Acrobat Reader for other languages, please download the appropriate version from the Internet. (Please
note that you do not have to have Acrobat Reader in your own language. You can read any pdf file using the English version of
Acrobat Reader.)
Accessing the PDF Manuals
For Windows:
1
2
3
4
5
6
Insert the CD-ROM in the CD-ROM drive.
Double click on the “My Computer” icon.
Double click on the “CD-ROM” drive.
Double click on the “manuals” folder.
Double click on the “xg-nv7xu” folder.
Double click on the language (name of the folder)
that you want to view.
7 Double click on the “nv7” pdf file to access the
projector manuals.
Double click on the “saps” pdf file to access the
Sharp Advanced Presentation Software manual.
8 Double click on the pdf file.
For Macintosh:
1
2
3
4
5
Insert the CD-ROM in the CD-ROM drive.
Double click on the “CD-ROM” icon.
Double click on the “manuals” folder.
Double click on the “xg-nv7xu” folder.
Double click on the language (name of the folder)
that you want to view.
6 Double click on the “nv7” pdf file to access the
projector manuals.
Double click on the “saps” pdf file to access the
Sharp Advanced Presentation Software manual.
7 Double click on the pdf file.
• If the desired pdf file cannot be opened by double clicking the mouse, please start Acrobat Reader first, then specify the
desired file using the “File”, “Open” menu.
• See the “readme.txt” file on the CD-ROM for information on the CD-ROM.
For SHARP Assistance (U.S.A. only)
If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting”
section on page 49. If this operation manual does not answer your question, please call toll free 1-800-BE-SHARP
(1-800-237-4277) for further assistance. Or, send us an e-mail at lcdsupport@sharplcd.com .
Our World Wide Web address is http://www.sharp-usa.com/ .
E-6
Part Names
Important
Information
Numbers next to the part names refer to the main pages in this manual where the topic is explained.
Projector
Front and Top View
MUTE button
17
47
LAMP REPLACEMENT
indicator
POWER indicator
16
47
TEMPERATURE WARNING
indicator
POWER buttons (ON/OFF)
16
17
17
VOLUME buttons (/)
KEYSTONE button
19
23
MENU button
INPUT button
17
25
IrCOM button
FREEZE button
33
29
AUTO SYNC button
ENLARGE button
34
36
RESIZE button
UNDO button
19
35
GAMMA button
ADJUSTMENT buttons
(∂ /ƒ/ß / ©)
23
23
ENTER button
17
Zoom ring
17
Focus ring
Speaker
Remote control sensor
Cooling fan (Exhaust vent)
Foot releases
21
5
19
Side and Rear View
Cooling fan (Intake vent)
E-7
IrCOM sensor
25
AC socket
11
Kensington Security
Standard connector
49
INPUT 2 port
13
INPUT 1 port (HD 15)
11
12 RCA
AUDIO INPUT terminal
(3.5 mm stereo minijack)
11
12 RCA
RS-232C port
(9-pin mini-DIN)
14
12 4 pin mini DIN
21 Remote control sensor
AUDIO INPUT terminals:
VIDEO INPUT terminal:
S-VIDEO INPUT terminal:
Part Names
Front View
Important
Information
Remote Control
Rear View
MUTE button 17
POWER buttons
(ON/OFF)
16
17
17 VOLUME buttons
(/)
KEYSTONE/BLACK
SCREEN button
19
37
22 LASER POINTER/
23 MENU button
RIGHT-CLICK/
ENTER button
22
23
22 MOUSE/
ADJUSTMENT
23 buttons (∂/ƒ/ß/©)
INPUT button
17
25 IrCOM button
FREEZE button
33
29 AUTO SYNC button
ENLARGE button
34
36 RESIZE button
TOOLS button
44
35 GAMMA button
MOUSE/
ADJUSTMENT
switch
21
22 BACKLIGHT button
19 LEFT-CLICK/
UNDO
22 button
Top View
Remote control
signal transmitter
5
Laser
pointer
window
Inserting the batteries
1
Press in and downward
on the arrow to remove
the battery cover.
Battery
cover
2
Insert two AA size batteries
for the remote control,
making sure their polarities
match the and marks
inside the battery
compartment.
Battery
compartment
3
Insert the side tabs of
the battery cover into
their slots and press the
cover in until it is
properly seated.
Battery
cover
E-8
Setup & Connections
Setup & Connections
E-9
Supplied Accessories
Remote control
RRMCG1530CESA
Two AA size batteries
Mouse control
cable for IBM PS/2
QCNW-5113CEZZ
Computer audio cable
QCNW-4870CEZZ
Mouse control
serial cable
QCNW-5112CEZZ
Mouse control cable
for Mac
QCNW-5114CEZZ
DIN-D-sub RS-232C cable
QCNW-5288CEZZ
Remote mouse receiver
RUNTK0661CEZZ
Carrying bag
GCASN0003CESA
Lens cap
GCOVH1308CESA
Setup & Connections
Computer cable
QCNW-5304CEZZ
Power cord
QACCU5013CEZZ
Lens cap strap
UBNDT0012CEZZ
CD-ROM
UDSKA0009CE01
Sharp Advanced Presentation
Software operation manual
TINS-6888CEZZ
Projector operation manual
TINS-6786CEZZ
Sharp Advanced Presentation
Software quick reference
TINS-6788CEZZ
Projector quick reference
TINS-6787CEZZ
IrDA driver installation
instruction sheet
TCAUZ3046CEZZ
E-10
Connecting the Projector
Connecting the Power Cord
Plug the supplied power cord into the AC socket on the back of the projector.
Setup & Connections
Power cord
QACCU5013CEZZ
Connecting the Projector to a Computer
You can connect your projector to a computer for projection of full color computer images.
To a computer using the standard 15-pin (VGA) input
Computer cable
QCNW-5304CEZZ
Computer audio cable
QCNW-4870CEZZ
1 Connect one end of the supplied computer cable to
the INPUT 1 port on the projector.
2 Connect the other end to the Monitor output port on the
computer. Secure the connectors by tightening the
thumb screws.
3 To use the built-in audio system, connect one end of
the supplied computer audio cable to the AUDIO INPUT
terminal on the projector.
4 Connect the other end to the Audio output terminal on
the computer.
CAUTION
• Before connecting, be sure to turn both the projector and the
computer off. After making all connections, turn the projector
on first. The computer should always be turned on last.
• Please read the computer’s operation manual carefully.
• Refer to pages 55 and 56 “Input Signals (Recommended
Timing)” for a list of computer signals compatible with the
projector. Use with computer signals other than those listed may
cause some of the functions not to work.
When connecting this projector to a computer, select
“Computer/RGB” for “Signal Type” on the GUI menu. (See
page 40.)
• A Macintosh adaptor may be required for use with some
Macintosh computers. Contact your nearest Authorized Sharp
Industrial LCD Products Dealer or Service Center.
E-11
Connecting the Projector
Connecting other compatible computers
When connecting the projector to a compatible computer other than an IBM-PC (VGA/SVGA/XGA/SXGA/UXGA)
or Macintosh (i.e. Workstation), a separate cable may be needed. Please contact your dealer for more information.
When connecting this projector to a computer, select “Computer/RGB” for “Signal Type” on the GUI menu. (See page 40.)
• Connecting computers other than the recommended types may result in damage to the projector, the computer, or both.
• AUDIO INPUT accepts INPUT 1 or 2 port input.
Setup & Connections
“Plug and Play” function
• This projector is compatible with VESA-standard DDC 1/DDC 2B when connecting to a 15-pin analog terminal
and VESA-standard DDC 2B when connecting to a 20-pin digital terminal. The projector and a VESA DDC
compatible computer will communicate their setting requirements, allowing for quick and easy setup.
• Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last.
• The DDC, Plug and Play function of this projector operates only when used in conjunction with a VESA DDC compatible
computer.
To a computer using the direct digital input (PanelLink™)
Computer audio cable
QCNW-4870CEZZ
1 Connect one end of the digital cable to the INPUT 2
port on the projector.
2 Connect the other end to the corresponding terminal on a computer.
3 To use the built-in audio system, connect one and
of the supplied computer audio cable to AUDIO
INPUT terminal on the projector.
Connect the other end to the Audio output terminal
on the computer.
Digital cable (sold separately)
2 To digital output terminal
Computer audio cable (3.5 mm stereo minijack cable)
To audio output terminal
Computer
E-12
Connecting the Projector
Connecting the Projector to Video Equipment
You can connect your projector to a VCR, laser disc player, DVD player, DTV decoder and other audiovisual
equipment.
CAUTION
• Always turn off the projector while connecting to video equipment, in order to protect both the projector and the equipment
being connected.
To a video source (VCR, laser disc player, DTV decoder or DVD player) using the standard video input
Setup & Connections
1 Connect the yellow RCA connectors to the corresponding
yellow VIDEO INPUT terminal on the projector and the Video
output terminal on the video source.
2 To use the built-in audio system, connect the red and white
RCA connectors to the corresponding red and white AUDIO
INPUT terminals on the projector and the Audio output
terminals on the video source.
The S-VIDEO INPUT terminal uses a video signal system in which
the picture is separated into a color and a luminance signal to
realize a higher-quality image.
• For higher quality video, you may use the S-VIDEO INPUT terminal on
the projector. S-video cable is sold separately.
• If your video equipment does not have an S-video output terminal, use
the Composite video output terminal.
S-video cable (sold separately)
To S-video output terminal
1 Video cable (sold separately)
To video output terminal
VCR
or
Laser disc player
2 Audio cable (sold separately)
To audio output terminals
To a DTV decoder or DVD player
Computer audio cable
QCNW-4870CEZZ
1 Connect one end of the HD-15-RGB cable to the INPUT 1
port on the projector.
2 Connect the other end to the corresponding terminals on the
video source.
3 To use the built-in audio system, connect one end of the
supplied computer audio cable to AUDIO INPUT terminal on
the projector.
Connect the other end to the Audio output terminal on the
video source.
Select “Computer/RGB” or “Component” for “Signal Type” on
the GUI menu, depending on the video source.
HD-15-RGB cable (sold separately)
2 To video input terminals
DTV decoder
or
DVD player
Computer audio cable (3.5 mm stereo minijack cable)
To audio output terminal
E-13
Connecting the Projector
Connecting RS-232C Port
When the RS-232C port on the projector is connected to a computer with an RS-232C cable (cross type, sold
separately), the computer can be used to control the projector and check the status of the projector. See pages 53
and 54 for details.
Computer cable
QCNW-5304CEZZ
DIN-D-sub RS-232C
cable
QCNW-5288CEZZ
Setup & Connections
Computer audio cable
QCNW-4870CEZZ
1 Connect the supplied DIN-D-sub RS-232C cable to the RS-232C port on the projector.
2 Connect a RS-232C cable (sold separately) to the other end of DIN-D-sub RS-232C cable and to the serial
port on the computer.
2 RS-232C cable
(cross type, sold separately)
1 DIN-D-sub
RS-232C cable
CAUTION
• Do not connect or remove RS-232C cable to or from the computer while it is on. This may damage your computer.
• The wireless mouse or RS-232C function may not operate if your computer port is not correctly set up. Please refer to the
operation manual of the computer for details on setting up/installing the correct mouse driver.
• The arrows (→, ↔) indicate the direction of the signals.
E-14
Connecting the Projector
Connecting the Remote Mouse Receiver
• You can use the remote control as a remote mouse.
• When the RS-232C port on the projector is connected to a computer with
an RS-232C cable (cross type, sold separately), the computer can be
used to control the projector and check the status of the projector. See
pages 53 and 54 for details.
Setup & Connections
IBM or IBM compatible PC
1 Connect one end of the supplied mouse control cable to the corresponding terminal on the PC.
2 Connect the other end to the remote mouse receiver.
or
Mouse control
serial cable
QCNW-5112CEZZ
IBM PC/AT
Mouse control cable
for IBM PS/2
QCNW-5113CEZZ
Remote mouse
receiver
RUNTK0661CEZZ
IBM PS/2
Remote mouse receiver
Use this terminal to connect the supplied
mouse control cable to
the remote mouse
receiver.
Mouse control cable
for Mac
QCNW-5114CEZZ
Mouse control
serial cable
QCNW-5112CEZZ
Macintosh
1 Connect the mouse control serial cable to the remote mouse receiver.
2 Connect the mouse control cable for Mac to the Mac ADB port on the Mac.
3 Connect the other end of the mouse control cable for Mac to the mouse control serial cable.
CAUTION
Download PDF

advertising