advertisement
Models WL93 and SM93 User Guide
GENERAL
Shure Model WL93 and SM93 Microphones are omnidirectional, subminiature, lavalier electret condenser microphones. Their visually unobtrusive design and tailored frequency response make them ideal for body-worn applications in TV broadcasting, theater, and sound reinforcement. Both the Model WL93 and the SM93 feature a small microphone element that provides full, clear sound comparable to that of much larger microphones.
The WL93, intended for wireless use, connects directly to a
Shure wireless body-pack transmitter. The SM93, intended for wired applications, includes a preamplifier assembly for connection to three-pin professional (XLR) audio connectors.
The SM93 requires phantom power, and operates over a range of 11 to 52 Vdc, covering both DIN and IEC phantom power standards.
FEATURES
• Subminiature lavalier design; ideal size for theater, television broadcasting, video, film, and sound reinforcement
• Small, inconspicuous mounting hardware
• Full, clear sound comparable to larger microphones
• Smooth extended frequency response with presence rise specially tailored for chest-worn microphone operation
• Controlled low-frequency rolloff reduces low-frequency clothing and room noise
• Low distortion, wide dynamic range
• Uniform omnidirectional polar pattern
• Preamplifier assembly (SM93) can be pocketed, strapped to the body, or clipped to belt or waistband
• Wide-range phantom powering (SM93) accepts all commonly used voltages
VARIATIONS
Version Cable
WL93
SM93
1 2 m (4 ft )
Color
Black matte microphone and
WL93–6 1.8 m (6 ft.)
WL93T 1.2m (4 ft.) Tan matte microphone and
WL93–6T 1.8 m (6 ft.) cable with tan accessories
CONNECTIONS
Connect the male, four-pin miniature connector (TA4M) at the end of the 93 microphone cable to the supplied preamplifier (SM93) or to a Shure wireless body–pack (WL93).
NOTE: Do not connect the 93 microphone directly to a mixer without using the supplied preamplifier or body-pack.
MOUNTING THE MICROPHONE
The tie clips and mounting bracket provided with the WL93 and SM93 allow the user to wear the microphone in a variety of ways. To achieve optimum pickup, attach the microphone to the user’s chest. You can also obtain high–quality sound when the microphone is worn in the hair, sewn into clothing, or attached to an acoustic instrument such as a guitar.
• Tie Clip. A spring-loaded clasp attaches easily to a necktie, lapel, blouse, or shirt. Snap the microphone into the clip’s mounting bracket and attach the clip to an article of clothing. The dual tie clip supplied with the SM93 provides simultaneous mounting of two microphones.
• Sew-On Bracket. Sew the supplied sew-on mounting bracket directly to a garment (Figure1). Use dark or light thread as necessary to match the color of the the bracket.
MICROPHONE
GARMENT
BRACKET
THREAD
SEW–ON MOUNTING
FIGURE 1
MOUNTING THE SM93 PREAMPLIFIER
Use the spring-loaded belt clip to hold the amplifier to a belt, skirt or trouser waistband, or inside pocket.
WINDSCREENS
An acoustic foam windscreen is supplied to help reduce undesirable wind noise associated with outdoor miking.
2003, Shure Incorporated
27C3106 (CG)
Printed in U.S.A.
POWERING THE SM93 PREAMPLIFIER
Power the preamplifier supplied with the SM93 using any phantom supply providing 11 to 52 Vdc, such as the Shure
Model PS1A Power Supply.
SM93 PREAMPLIFIER IMPEDANCE
Use a minimum load impedance of 800 Ω or greater for maximum signal handling and minimum distortion. Load as low as 150 Ω can be used, but a reduction in output clipping level will result. Note that the power supply itself may add loading (3300 Ω in the Shure PS1A) to the microphone.
USING OTHER PREAMPLIFIERS OR BODY–PACKS
If connecting the 93 microphone to anything OTHER than a Shure wireless body-pack or the preamplifier supplied with the SM93, make sure it provides a regulated +5 Vdc source
( 40 mA minimum) at pin 2 of the microphone connector, as shown in Figure 2.
CONDENSER
CARTRIDGE
IMPEDANCE
CONVERTER
G
D+
S
RED
BLK
SHIELD
MICROPHONE WIRING DIAGRAM
FIGURE 2
1
4
3
2
SPECIFICATIONS
Type
Frequency Response (Figure 4)
Polar Pattern
Output Impedance
WL93 MICROPHONE (with standard test circuit shown in Figure 3)
Condenser (electret bias)
50 to 20,000 Hz
Omnidirectional, uniform with frequency
3000 Ω
SM93 MICROPHONE (with preamplifier)
Condenser (electret bias)
80 to 20,000 Hz, 12 dB/octave rolloff below 100 Hz
Omnidirectional, uniform with frequency
Rated at 150 Ω (90 Ω actual)
Recommended minimum load impedance: 800 Ω
(May be used with loads as low as 150 Ω with reduced clipping level)
Open Circuit Voltage: –43 dBV/Pa (7.0 mV) Output Level
(1 Pascal = 94 dB SPL)
Output Clipping Level
(at 1,000 Hz)
Total Harmonic Distortion
Maximum SPL
Open Circuit Voltage: –38 dBV/Pa
(13 mV)
0.25 V at 120 dB
Less than 1% at 120 dB
120 dB
Dynamic Range (maximum SPL to A-weighted noise level)
102 dB
Output Noise (equivalent SPL) 18 dB typical, A-weighted
Hum Pickup (electromagnetic)
Signal-to-Noise Ratio
Polarity
Recommended Operating
Voltage
Current Drain
Environmental Conditions
Cable
Case
N/A
76 dB at 94 dB SPL (IEC 651)
Positive pressure on microphone diaphragm produces positive voltage on pins 3 and 4 with respect to pin 1 (ground)*
2 to 10 V; 5 V nominal (pin 2 to pins 3 and 4)
–18 dBV (0.13 V) minimum
Less than 1% at 120 dB
120 dB
98 dB
22 dB typical, A-weighted
26 dB, weighted per DIN 45 405
–4 dB equivalent SPL in a 1 mOe field (60 Hz)
72 dB at 94 dB SPL (IEC 651)
Positive pressure on microphone diaphragm produces positive voltage on pin 2 relative to pin 3 of preamplifier output cable connector
11 to 52 Vdc phantom. Protected against reverse voltage application
0.33 mA
Operating Temperatures: –18
Storage Temperatures: –29 o o to 57 o C (0 o to 135 o F)
to 74 o C (–20 o to 165 o F)
40 mA typical
Operating Temperatures:
Storage Temperatures:
–18 o
(0 o
to 57 o C
to 135 o F)
–29 o to 74 o C
(–20 o to 165 o F)
Black 1.27 m (4.17 ft), attached, two-conductor, shielded, terminated by miniature connector type
TA4F (WL93T: Tan 1.27 m [4.17 ft])
Microphone: Black ABS thermoplastic case with stainless-steel-mesh grille
Black 1.27 m (4.17 ft), attached, two-conductor, shielded, terminated by miniature connector type
(TA4F)
Microphone: Black ABS thermoplastic case with stainless-steel-mesh grille
P lifi St l ith finish, black–chrome belt clip fl ti bl k
Net Weight Microphone: 16 g (0.57 oz)
Preamplifier: 118 g (4.17 oz)
* Produces positive voltage at pin 2 of Shure L4/EC4 wireless receiver three–pin connector.
2
FURNISHED ACCESSORIES
Preamplifier (SM93) . . . . . . . . . . . . . . . . . . . . . . .
Black Windscreen (WL93, SM93)
Tan Windscreen (WL93T)
. . . . . . . . . .
Black Tie Clip Assembly (WL93, SM93)
Dual Black Tie Clip Assembly (SM93)
. . . . .
. . . . . . .
90A4360
RK355WS*
. . . . . . . . . . . . . . . . .
Tan Tie Clip Assembly (WL93T) . . . . . . . . . . . .
RK354SB*
RK307DB
RK304T**
RK304T**
Black Sew-on Mounting Bracket (WL93, SM93) 65B1733
Tan Sew-on Mounting Bracket (WL93T)
Zippered Carrying Bag
. . . .
. .
65B1733A
. . . . . . . . . . . . . . . . . . . . . . . 26A13
* Replacements furnished in multiples of 4.
** RK304 includes 2 tie clips and 2 windscreens.
OPTIONAL ACCESSORIES
In-Line On/Off Switch . . . . . . . . . . . . . . . . . . . . . . . WA360
CERTIFICATION
Eligible to bear CE Marking. Conforms to European EMC
Directive 89/336/EEC. Meets applicable tests and performance criteria in European Standard EN 55103 (1996) parts
1 and 2, for residential (E1) and light industrial (E2) environments.
2.2 mF
V out
1
4
2
3
20 K
+5V
TEST CIRCUIT
FIGURE 3
SM93
+10
0
–10
20 50 100 200 500 1,000 2,000 5,000 10,000 20,000
Hz
TYPICAL FREQUENCY RESPONSE
FIGURE 4
27 mm
(1–1/16 IN.)
98.8 mm
(3–29/32 IN.)
ÁÁÁÁ ÁÁ ÁÁÁÁ Á Á Á Á Á
Á Á ÁÁ Á Á ÁÁÁÁ Á Á ÁÁÁÁ Á Á ÁÁ Á Á Á Á Á ÁÁ
SM93 PREAMPLIFIER
18.8 mm
(3/4 IN.)
ÁÁÁ Á ÁÁ ÁÁ Á Á Á Á Á Á Á Á Á Á Á ÁÁ Á Á Á Á Á Á Á Á Á Á ÁÁ Á Á Á ÁÁ Á ÁÁ Á Á Á Á ÁÁ Á Á Á Á Á ÁÁÁÁ Á ÁÁÁÁ Á Á Á ÁÁ ÁÁ Á
Á Á ÁÁ Á Á Á ÁÁ Á ÁÁ Á Á Á ÁÁ Á ÁÁ ÁÁ Á
0.37 IN
(9.40 mm)
0.15 IN.
(3.81 mm)
0.23 IN.
(5.84 mm)
0.24 IN.
(6.10 mm)
OVERALL DIMENSIONS
FIGURE 5
SM93/WL93 MICROPHONE
RED
C
P2
1
4
2
3
BLK
.1V
B
1.9V
C3
33X6.3
C7
.047,5%
R4
360K
C6
.047,5%
.6V
R5
62K
C8
150 pF
R2
33K
Q2
86A350
C5
150 pF
R6
24K
GRN A
3.5V
4.1V
R1
D1
86B429
Q1
86A348
.1V
.05V
D2
86A415
NOTES:
1. ALL RESISTORS 5%,1/8 WATT, UNLESS OTHERWISE SPECIFIED.
2. ALL NON–POLAR CAPACITORS IN µ F, TOLERANCE 10% AND 50 VOLTS OR MORE
UNLESS OTHERWISE SPECIFIED. POLARIZED CAPACITORS SHOWN IN µ F x VOLTS.
3. D.C. VOLTAGES MEASURED WITH 11 MEG INPUT VOLTMETER; A.C. VOLTAGE MEA-
SURED WITH 1 MEG INPUT VOLTMETER. VALUES SHOWN ARE TYPICAL AND MAY
VARY ± 20%.
4. THE FOLLOWING SYMBOLS DENOTE:
CIRCUIT BOARD GROUND
CASE GROUND
A.C. VOLTAGE
D.C. VOLTAGE
WHT BLK GRN
5. POWER SOURCE IS 21 VDC THROUGH TWO 1.691 KOHM, 1% RESISTORS FROM
SUPPLY TO PINS 2 AND 3 OF CONNECTOR P1.
YEL
C1
150 pF
C2
150 pF
BRN
.05V
T1
L1
L2
2
1
3
2
3
1
6. INPUT SIGNAL OF 0.1V AT 2 KHZ
APPLIED TO CIRCUIT BELOW:
.1V
P1
10x10
18K
1.2K
C
B
A
SM93 PREAMPLIFIER CIRCUIT DIAGRAM
FIGURE 6
3
Micros–cravates SM93 et WL93
Les modèles Shure WL93 et SM93 sont des micros-cravates électrostatiques à électret, omnidirectionnels et sous-miniatures. Un aspect discret et une réponse en fréquence étudiée en font le choix idéal pour les applications où le microphone est porté sur le corps pour la télévision, le théâtre et la sonorisation de scène. Les deux modèles WL93 et SM93 comprennent un petit élément microphone donnant un son riche et clair comparable à celui de microphones bien plus gros.
Le WL93, prévu pour l’utilisation sans fil, se branche directement à un transmetteur de poche sans fil Shure. Le SM93, prévu pour les applications câblées, comprend un préamplificateur pour le branchement à des connecteurs audio professionnel trois broches (XLR). Le SM93 nécessite une alimentation en duplex. Il fonctionne sur une plage de 11 à 52 V c.c.
couvrant ainsi les normes d’alimentation en duplex DIN et IEC.
le microphone de diverses manières. Pour obtenir le captage optimum, fixer le microphone sur la poitrine de l’utilisateur. On peut aussi obtenir un son de haute qualité quand le microphone est porté dans les cheveux, cousu dans un vêtement ou fixé
à un instrument acoustique tel qu’une guitare.
• Barrette fixe-cravate. Un fermoir à ressort se fixe facilement à une cravate, un revers, un chemisier ou une chemise. Le microphone s’encliquette dans le bloc de montage de la barrette. La barrette fixe-cravate double fournie avec le SM93 permet de monter simultanément deux microphones.
• Bloc à coudre. Ce bloc se coud directement sur un vêtement (figure1). Utiliser un fil foncé ou clair selon le besoin en fonction de la couleur du bloc.
MICROPHONE
AVANTAGES
• Micro-cravate sous-miniature : Taille idéale pour le théâtre, la télévision, les productions vidéo ou film et la sonorisation de scène
• Petit matériel de montage discret
• Son clair et riche comparable à celui de plus gros microphones
• Réponse en fréquence uniforme étendue à courbe de présence étudiée spécialement pour le port sur la poitrine
• L’atténuation des basses contrôlée réduit les bruits à basse fréquence des vêtements ou de la salle
• Faible distorsion, large gamme dynamique
• Courbe de directivité omnidirectionnelle uniforme
• Le préamplificateur (SM93) se fixe sur une ceinture ou un vêtement
• Une large plage de tensions peut être utilisée pour alimenter le préamplificateur (SM93)
VARIATIONS
Version Câble
WL93
SM93
WL93–6 1,8 m
WL93T 1,2 m
WL93–6T 1,8 m
Couleur mats avec accessoires ocres
CONNEXIONS
Brancher le connecteur miniature mâle à quatre broches
(TA4M) à l’extrémité du câble de microphone 93 au préamplificateur fourni (SM93) ou à un système de poche sans fil
Shure (WL93).
REMARQUE : Ne pas brancher le microphone 93 directement sur une table de mélange sans utiliser le préamplificateur fourni ou un système de poche.
MONTAGE DU MICROPHONE
Les barrettes fixe-cravate et le bloc de montage fournis avec le WL93 et le SM93 permettent à l’utilisateur de porter
4
VÊTEMENT
BLOC
FIL
BLOC À COUDRE
FIGURE 1
MONTAGE DU PRÉAMPLIFICATEUR SM93
Utiliser l’attache pour ceinture à ressort pour fixer l’amplificateur à une ceinture, la ceinture d’une jupe ou d’un pantalon, ou à l’intérieur d’une poche.
COUPE–VENT
L’écran acoustique antivent en mousse fourni réduit le bruit de vent indésirable associé à la prise de son à l’extérieur.
ALIMENTATION DU PRÉAMPLIFICATEUR SM93
Alimenter le préamplificateur fourni avec le SM93 à l’aide d’une alimentation en duplex fournissant de 11 à 52 V c.c., par exemple le bloc d’alimentation modèle PS1A de Shure.
IMPÉDANCE DU PRÉAMPLIFICATEUR SM93
Utiliser une impédance de charge d’au moins 800 Ω pour obtenir une gestion maximum des signaux et une distorsion minimum. La charge peut être d’un minimum de 150 Ω, mais cela entraînera une réduction du niveau d’écrêtage en sortie. Il est à noter que l’alimentation elle–même peut ajouter une charge (3300 Ω pour le PS1A de Shure) au microphone.
UTILISATION D’AUTRES PRÉAMPLIFICATEURS OU
SYSTÈMES DE POCHE
Si le microphone 93 est raccordé à tout AUTRE appareil autre qu’un dispositif de poche sans fil Shure ou le préamplificateur fourni avec le SM93, s’assurer qu’il fournit une source d’alimentation de +5 V c.c. ( 40 mA minimum) à la broche
2 du connecteur du microphone, comme illustré à la figure 2.
CARACTÉRISTIQUES
Type
Courbe de réponse (Figure 3)
Courbe de directivité
Impédance de sortie
Niveau de sortie
(1 Pascal = 94 dB NPA)
Niveau d’écrêtage en sortie
(à 1000 Hz)
Distorsion harmonique totale
NPA maximum
Inférieure à 1 % à 120 dB
120 dB
Gamme dynamique (NPA maximum au niveau de bruit pondéré en A)
102 dB
Bruit en sortie (NPA équivalent) 18 dB typique, pondéré en A
Captage du ronflement
(électromagnétique)
Rapport signal/bruit
Polarité
Tension de service recommandée
Consommation de courant
Environnement
Câble
Corps
Poids net
MICROPHONE WL93 (avec circuit d’essai standard représenté à la figure 6)
Électrostatique (polarisation d’électret)
MICROPHONE SM93 (avec préamplificateur)
Électrostatique (polarisation d’électret)
50 à 20 000 Hz 80 à 20 000 Hz, atténuation de 12 dB/octave en dessous de 100 Hz
Omnidirectionnelle, uniforme selon la fréquence Omnidirectionnelle, uniforme selon la fréquence
3000 Ω Valeur nominale à 150 Ω (90 Ω réelle)
Impédance de charge minimum recommandée : 800 Ω
(usage possible avec charges d’un minimum de 150 Ω avec niveau d’écrêtage réduit)
Tension de circuit ouvert : –43 dBV/Pa (7,0 mV) Tension de circuit ouvert : –38 dBV/Pa
(13 mV)
0,25 V à 120 dB –18 dBV (0,13 V) minimum
S. O.
76 dB à 94 dB NPA (IEC 651)
Une pression positive sur le diaphragme du microphone produit une tension positive sur les broches 3 et 4 par rapport à la broche 1
(masse)*
2 à 10 V; 5 V nominaux (broche 2 par rapport aux broches 3 et 4)
40 mA typiques
Températures de fonctionnement : –18 à 57 o C
Températures de stockage : –29 à 74 o C
Noir de 1,27 m, intégré, à deux conducteurs, blindé, à connecteur miniature type TA4F (WL93T
: Ocre de 1,27 m)
Microphone : Corps noir en thermoplastique à grille en acier inoxydable
Microphone : 16 g
Inférieure à 1 % à 120 dB
120 dB
98 dB
22 dB typique, pondéré en A
26 dB, pondéré selon DIN 45 405
–4 dB équivalent NPA dans un champ de 1 mOe
(60 Hz)
72 dB à 94 dB NPA (IEC 651)
Une pression positive sur le diaphragme du microphone produit une tension positive sur la broche
2 par rapport à la broche 3 du connecteur de câble de sortie préamplificateur
11 à 52 V c.c. duplex. Protégé contre les inversions de polarité
0,33 mA
Températures de fonctionnement : –18 à 57 o
Températures de stockage : –29 à 74 o C
C
Noir de 1,27 m, intégré, à deux conducteurs, blindé, à connecteur miniature type TA4F
Microphone : Corps noir en thermoplastique à grille en acier inoxydable
P é lifi t C i à fi iti i réfléchissante, attache pour ceinture noire et chromée
Microphone : 16 gg
Préamplificateur : 118 g
* Produit une tension positive à la broche 2 du connecteur à trois broches du récepteur sans fil Shure L4/EC4.
ACCESSOIRES FOURNIS
Préamplificateur (SM93) . . . . . . . . . . . . . . . . . . . .
Coupe–vent noir (WL93, SM93)
Coupe–vent ocre (WL93T)
. . . . . . . . . . .
Barrette fixe–cravate noire (WL93, SM93)
Barrette fixe–cravate double noire (SM93)
Barrette fixe–cravate ocre (WL93T)
90A4360
RK355WS*
. . .
. . .
. . . . . . . . . . . . . . . .
. . . . . . . . .
Bloc de montage à coudre noir (WL93, SM93)
Bloc de montage à coudre ocre (WL93T)
RK354SB*
RK307DB
. . .
. . .
Fourre–tout pour le transport à fermeture éclair
RK304T**
RK304T**
65B1733
65B1733A
. . 26A13
* Pièces de rechange fournies en multiples de 4.
** RK304 comprend 2 barrettes fixe–cravate et 2 coupe–vent.
ACCESSOIRES EN OPTION
Interrupteur marche–arrêt en ligne . . . . . . . . . . . . WA360
HOMOLOGATION
Autorisé à porter la marque CE. Conforme à la directive
CEM européenne 89/336/CEE. Conforme aux critères applicables de test et de performances de la norme européenne EN 55103 (1996) parties 1 et 2 pour les environnements résidentiels (E1) et d’industrie légère (E2).
5
SM93 und WL93 Lavalier-Mikrofone
Die Mikrofone Shure Modell WL93 und SM93 sind Lavalier-
Elektret-Kondensatormikrofone mit Kugelcharakteristik im
Kleinformat. Durch ihre unauffällige Ausführung und den präzise abgestimmten Frequenzgang sind sie ideal geeignet für das Tragen am Körper bei Fernsehausstrahlungen, im Theater und für Beschallungsanlagen. Die Modelle WL93 und
SM93 verfügen beide über kleine Mikrofonelemente, die einen vollen, deutlichen Klang ergeben, der mit dem von viel größeren Mikrofonen vergleichbar ist.
Der WL93, der für drahtlosen Einsatz vorgesehen ist, wird direkt an einen drahtlosen Taschensender von Shure angeschlossen. Der SM93 ist für Anwendungen mit Kabelverbindung vorgesehen und enthält eine Vorverstärkereinheit für den Anschluß von professionellen dreipoligen XLR-Audiosteckern. Der SM93 erfordert Phantomspeisespannung und arbeitet in einem Bereich von 11 bis 52 V Gleichspannung, so daß sowohl die DIN- als auch die IEC-Normen für Phantomspeisespannung erfüllt sind. ner optimalen Aufnahme des Tons sollte das Mikrofon im Brustbereich des Trägers angebracht werden. Eine gute Klangqualität läßt sich auch erzielen, wenn das Mikrofon im Haar getragen, in der Kleidung eingenäht oder an einem akustischen
Instrument wie zum Beispiel eine Gitarre befestigt wird.
• Krawattenklemme. Eine federbelastete Klemme läßt sich einfach an einer Krawatte, einem Aufschlag, einer Bluse oder einem Hemd anbringen. Das Mikrofon rastet in der
Halterung der Klemme ein. Die Doppelkrawattenklemme, die mit dem SM93 geliefert wird, gestattet es, gleichzeitig zwei Mikrofone anzubringen.
• Halterung zum Annähen. Diese Halterung wird direkt an ein Kleidungsstück genäht (Abbildung1). Entsprechend der Farbe der Halterung einen dunklen oder hellen Faden verwenden.
MIKROFON
TECHNISCHE EIGENSCHAFTEN
• Lavalier-Ausführung im Kleinformat, die ideale Größe für
Theater, Fernsehsendungen, Video, Film und Beschallung
• Kleine, unauffällige Befestigungsteile
• Voller, deutlicher Klang, vergleichbar mit größeren Mikrofonen
• Ausgeglichener, erweiterter Frequenzgang mit Präsenzanhebung, speziell abgestimmt auf Anwendungen mit Befestigung im Brustbereich
• Geregeltes Niederfrequenz-Rolloff reduziert niederfrequente Geräusche durch Kleidung und aus dem Raum
• Niedrige Verzerrung, breiter Dynamikbereich
• Gleichförmige Kugel-Richtcharakteristik
• Vorverstärker (SM93) wird an Gürtel oder Rock-/Hosenbund angeklemmt
• Vorverstärker (SM93) kann mit einem großen Spannungsbereich betrieben werden
AUSFÜHRUNGEN
Version Kabel
WL93
SM93
WL93–6 1,8 m
WL93T 1,2 m
WL93–6T 1,8 m
Farbe braun, Zubehörteile gelbbraun
ANSCHLÜSSE
Den vierpoligen Miniatur (TA4M) Stecker am Ende des Mikrofonkabels 93 an den mitgelieferten Vorverstärker (SM93) oder an einen drahtlosen Taschensender von Shure (WL93) anschließen.
HINWEIS: Das Mikrofon 93 nicht direkt an ein Mischpult ohne den mitgelieferten Vorverstärker oder einen Taschensender anschließen.
ANBRINGEN DES MIKROFONS
Die Krawattenklemme und die Halterung, die mit dem
WL93 und SM93 mitgeliefert werden, ermöglichen es, das
Mikrofon auf verschiedene Weise zu tragen. Zur Erzielung ei-
KLEIDUNGSSTÜCK
HALTERUNG
FADEN
HALTERUNG ZUM ANNÄHEN
ABBILDUNG 1
BEFESTIGUNG DES VORVERSTÄRKERS SM93
Den Vorverstärker mit der federbelasteten Gürtelklemme an einen Gürtel, einen Rock- oder Hosenbund oder in einer
Tasche befestigen.
WINDSCHUTZ
Der mitgelieferte Schaumstoff-Windschutz reduziert unerwünschte Windgeräusche, die bei Verwendung des Mikrofons im Freien vorkommen.
SPANNUNGSVERSORGUNG DES VORVERSTÄRKERS
SM93
Die Spannungsversorgung des mit dem SM93 mitgelieferten Vorverstärkers kann mit jeder Phantomspeisespannung von 11 bis 52 V Gleichspannung wie zum Beispiel dem Netzteil Shure Modell PS1A erfolgen.
IMPEDANZ DES VORVERSTÄRKERS SM93
Zur Erzielung von maximaler Signalverarbeitung und minimaler Verzerrung eine Abschlußimpedanz von mindestens
800 Ω verwenden. Abschlußimpedanzen ab 150 Ω können verwendet werden, führen jedoch zu einer Verringerung des
Ausgangsbegrenzungspegels. Es ist zu beachten, daß das
Netzteil selbst die Last (3300 Ω im Netzteil Shure PS1A) am
Mikrofon erhöhen kann.
VERWENDUNG ANDERER VORVERSTÄRKER ODER
TASCHENSENDER
Wenn das Mikrofon 93 an etwas ANDERES als einen drahtlosen Taschensender von Shure oder den mit dem
SM93 gelieferten Vorverstärker angeschlossen wird, muß sichergestellt werden, daß eine geregelte Spannung von +5 V
Gleichspannung ( 40 mA min.) an Stift 2 des Mikrofonsteckers bereitgestellt wird, wie in Abbildung 2 dargestellt.
6
TECHNISCHE DATEN
Typ
Frequenzgang (Abbildung 3)
Richtcharakteristik
MIKROFON WL93 (mit Standard–Prüfschaltung dargestellt in Abbildung 6)
Kondensatormikrofon (Elektretvorpolung)
50 bis 20.000 Hz
Kugelcharakteristik, mit gleichförmigem
Frequenzgang
3000 Ω
MIKROFON SM93 (mit Vorverstärker)
Kondensatormikrofon (Elektretvorpolung)
80 bis 20.000 Hz, 12 dB/Oktave Rolloff unter 100 Hz
Kugelcharakteristik, mit gleichförmigem Frequenzgang
Ausgangsimpedanz
Ausgangspegel
(1 Pascal = 94 dB
Schalldruckpegel)
Ausgangs–Clipping–Pegel (bei
1.000 Hz)
Gesamtklirrfaktor
Maximaler Schalldruckpegel
Dynamikbereich (maximaler
Schalldruckpegel bis
Geräuschpegel mit
Bewertungskurve A)
Ausgangsrauschen
(äquivalenter Schalldruckpegel)
Brummeinkopplung
(elektromagnetisch)
Signalrauschabstand
Leerlaufspannung: –38 dBV/Pa
(13 mV)
0,25 V bei 120 dB
Weniger als 1 % bei 120 dB
120 dB
102 dB typisch 18 dB, Bewertungskurve A
–
76 dB bei 94 dB Schalldruckpegel (IEC 651)
Polarität Positiver Druck an der Mikrofonmembran erzeugt positive Spannung an Stift 3 und 4 in bezug auf
Stift 1 (Masse)*
Empfohlene Betriebsspannung 2 bis 10 V; 5 V nominal (Stift 2 zu Stift 3 und 4)
Nennwert: 150 Ω (Ist–Wert: 90 Ω)
Empfohlene Mindestabschlußimpedanz: 800 Ω (kann mit Abschlußimpedanzen ab 150 Ω bei verringertem
Clipping–Pegel verwendet werden)
Leerlaufspannung: –43 dBV/Pa (7,0 mV)
–18 dBV (0,13 V) min.
Weniger als 1 % bei 120 dB
120 dB
98 dB typisch 22 dB, Bewertungskurve A
26 dB, Bewertungskurve nach DIN 45 405
Entspricht –4 dB Schalldruckpegel in einem Feld mit 1
Millioersted (60 Hz)
72 dB bei 94 dB Schalldruckpegel (IEC 651)
Positiver Druck an der Mikrofonmembran erzeugt positive Spannung an Stift 2 in bezug auf Stift 3 des
Ausgangskabelsteckverbinders des Vorverstärkers
11 bis 52 V Phantom-Gleichspannung. Geschützt gegen Gegenspannung
0,33 mA
Betriebstemperaturen: –18 o C bis 57
Lagerungstemperaturen: –29 o o C
C bis 74 o C
Stromaufnahme
Umweltbedingungen
Kabel
40 mA typisch
Betriebstemperaturen: –18 o C bis 57 o C o C
Schwarz 1,27 m, angebracht, zweipolig, abgeschirmt, abgeschlossen mit Miniatur
Steckverbinder TA4F (WL93T: gelbbraun 1,27 m )
Mikrofon: Gehäuse aus schwarzem
ABS–Thermoplast mit Gittergrill aus rostfreiem
Stahl
Schwarz 1,27 m, angebracht, zweipolig, abgeschirmt, abgeschlossen mit Miniatur Steckverbinder TA4F
Gehäuse
Nettogewicht Mikrofon: 16 g
Mikrofon: Gehäuse aus schwarzem ABS–Thermoplast mit Gittergrill aus rostfreiem Stahl
Vorverstärker: Schwarzes, nicht reflektierendes
Stahlgehäuse, Gürtelklemme aus schwarzem Chrom
Mikrofon: 16 gg
Vorverstärker: 118 g
* Erzeugt positive Spannung an Stift 2 des dreipoligen Steckverbinders des drahtlosen Empfängers Shure L4/EC4.
MITGELIEFERTES ZUBEHÖR
Vorverstärker (SM93) . . . . . . . . . . . . . . . . . . . . . .
Schwarzer Windschutz (WL93, SM93)
90A4360
. . . . . . RK355WS*
.
Schwarze Doppelkrawattenklemme (SM93) RK307DB
Gelbbrauner Windschutz (WL93T)
Gelbbraune Krawattenklemme (WL93T)
. .
. . . . . . . . .
. . . . .
RK304T**
RK304T**
Schwarze Halterung zum Annähen (WL93, SM93) 65B1733
Gelbbraune Halterung zum Annähen (WL93T) 65B1733A
Reißverschlußtasche . . . . . . . . . . . . . . . . . . . . . . . . 26A13
* Ersatzteile werden in 4er–Sätzen geliefert.
** RK304 enthält 2 Krawattenklemmen und 2 Windschirme.
SONDERZUBEHÖR
In-Line–Ein/Aus–Schalter . . . . . . . . . . . . . . . . . . . . WA360
ZERTIFIZIERUNG
Zur CE–Kennzeichnung berechtigt. Entspricht der EU–
Richtlinie über elektromagnetische Verträglichkeit
89/336/EEC. Erfüllt die Prüfungs- und Leistungskriterien der europäischen Norm EN 55103 (1996) Teil 1 und 2 für Wohngebiete (E1) und Leichtindustriegebiete (E2).
7
Micrófonos de corbata SM93 y WL93
Los micrófonos Shure modelos WL93 y SM93 son micrófonos de corbata omnidireccionales y subminiatura de condensador de electreto. Su diseño discreto a la vista y su respuesta de frecuencia ajustada los hacen ideales para usarse portados en el cuerpo, como en el caso de la teledifusión, teatro y amplificación de sonido. Tanto el modelo WL93 como el
SM93 incorporan un pequeño elemento de micrófono que proporciona un sonido pleno y claro comparable al de micrófonos de tamaño mucho mayor.
El WL93, concebido para uso inalámbrico, se conecta directamente a un emisor portátil inalámbrico de Shure. El SM93, concebido para aplicacones alámbricas, comprende un conjunto de preamplificador para conectar con conectores profesionales (XLR) de audio de tres clavijas. El SM93 requiere potencia fantasma, y funciona dentro de una gama de voltajes de
11 a 52 VCC, cumpliendo las normas de potencia fantasma
DIN e IEC.
MONTAJE DEL MICROFONO
Las presillas para corbata y el soporte de montaje suministrados con el WL93 y el SM93 permiten al usuario sujetar el micrófono de diversas maneras. La captación óptima se logra cuando el micrófono se coloca en el pecho del usuario. También puede obtenerse sonido de alta calidad si se coloca el micrófono en el cabello, se lo cose a la ropa o se lo sujeta a algún instrumento acústico, tal como una guitarra.
• Presilla para corbata. Un broche de resorte se prende fácilmente a una corbata, solapa, blusa o camisa. El micrófono se acopla al soporte de montaje de la presilla. La presilla doble para corbata que se suministra con el SM93 permite montar simultáneamente dos micrófonos.
• Soporte cosido. Este soporte va directamente cosido a una prenda (Figura1). Emplee hilo oscuro o claro según sea el color del soporte.
MICROFONO
CARACTERISTICAS
• Diseño subminiatura de corbata; tamaño ideal para uso en teatro, teledifusión, producciones de video o cinematográficas y amplificación de sonido
• Tornillería de montaje pequeña y poco perceptible
• Sonido pleno y claro comparable al de micrófonos de mayor tamaño
• Una gama amplia y uniforme de respuesta de frecuencias con aumento de frecuencias de presencia, especialmente diseñado para uso prendido en el pecho
• La atenuación progresiva y controlada de las frecuencias bajas reduce los ruidos de baja frecuencia producidos por el ambiente y por la ropa
• Baja distorsión y una amplia gama dinámica
• Patrón polar omnidireccional uniforme
• El preamplificador (SM93) se engancha al cinturón o pretina
• Puede usarse una amplia gama de voltajes para alimentar el preamplificador (SM93)
PRENDA
HILO
SOPORTE
MONTAJE COSIDO
FIGURA 1
MONTAJE DEL PREAMPLIFICADOR SM93
Emplee el gancho de resorte para fijar el amplificador a un cinturón, falda, pretina de falda o pantalón o al interior del bolsillo.
PARAVIENTOS
El paravientos acústico de espuma que se suministra ayuda a reducir los ruidos indeseables del viento durante el uso de micrófonos al aire libre.
ALIMENTACION DEL PREAMPLIFICADOR SM93
Alimente el preamplificador que se suministra con el SM93 con cualquier fuente de alimentación fantasma que proporcione entre 11 y 52 VCC, como la fuente de alimentación
Shure modelo PS1A.
VARIACIONES
Versión Cable
WL93
SM93
1,2 m
(4 pies)
WL93–6 1,8 m
(6 pies)
WL93T 1,2 m
(4 pies)
WL93–6T 1,8 m
(6 pies)
Color
Micrófono y cable en color café mate con accesorios en color café y mate con accesorios en negro
CONEXIONES
Conecte el conector miniatura macho de cuatro clavijas
(TA4M) situado en el extremo del cable del micrófono 93 al preamplificador suministrado (SM93) o a un emisor portátil inalámbrico de Shure (WL93).
NOTA: No conecte el micrófono 93 directamente a una consola mezcladora sin el preamplificador suministrado o un emisor portátil.
IMPEDANCIA DEL PREAMPLIFICADOR SM93
Para aumentar la capacidad de señales y reducir la distorsión es necesario usar una impedancia de carga de por lo menos 800 Ω. Se puede usar una carga mínima de 150 Ω, pero se producirá una reducción en el nivel de limitación de la salida. Obsérvese que la propia fuente de alimentación puede imponer una carga (3300 Ω con la fuente PS1A de
Shure) al micrófono.
USO DE OTROS PREAMPLIFICADORES O EMISORES
PORTATILES
Si el micrófono 93 se conecta a algo DISTINTO de un emisor portátil inalámbrico de Shure o al preamplificador que se suministra con el SM93, compruebe que proporciona una fuente regulada de +5 VCC ( 40 mA mínimo) en la clavija 2 del conector del micrófono, como se muestra en la Figura 2.
8
ESPECIFICACIONES
Tipo
Respuesta de frecuencia
(Figura 3)
Patrón polar
MICROFONO WL93 (con circuito normal de prueba mostrado en la Figura 6)
Condensador (electreto polarizado)
50 a 20.000 Hz
MICROFONO SM93 (con preamplificador)
Condensador (electreto polarizado)
80 a 20.000 Hz, atenuación progresiva de 12 dB/octava por debajo de 100 Hz
Omnidireccional, uniforme respecto a la frecuencia
Impedancia de salida
Nivel de salida
(1 Pascal = 94 dB SPL)
Nivel de limitación de salida (a
1000 Hz)
Distorsión armónica total
Nivel de presión acústica (SPL) máx.
Gama dinámica
(SPL máximo a nivel de ruido con ponderación A)
Ruido de salida (SPL equivalente)
Captación de zumbido
(electromagnético)
Relación de señal a ruido
Polaridad
Voltaje de funcionamiento recomendado
Consumo de corriente
Condiciones ambientales
Cable
Omnidireccional, uniforme respecto a la frecuencia
3000 Ω
Voltaje en circuito abierto: –38 dBV/Pa
(13 mV)
0,25 V a 120 dB
Menos del 1% a 120 dB
120 dB
102 dB
18 dB típico, ponderación A
N/C
76 dB a SPL de 94 dB (IEC 651)
Una presión positiva en el diafragma del micrófono produce un voltaje positivo en las clavijas 3 y 4 con respecto a la clavija 1 (tierra)*
2 a 10 V; 5 V nominal (clavija 2 a clavijas 3 y 4)
40 mA típico
Temperaturas de funcionamiento: –18 o a 57 o
(0 o a 135 o
C
F)
Temperaturas de almacenamiento: –29 o a 74
(–20 o a 165 o o
C
F)
Negro de 1,27 m (4,17 pies) de largo, integral, dos conductores, blindado y terminado con conector
Miniatura tipo TA4F (WL93T: Color café de 1,27 m
[4,17 pies])
Micrófono: Caja negra de plástico ABS termotratado con rejilla de acero inoxidable
Nominal: 150 Ω (Real: 90 Ω)
Impedancia de carga mínima recomendada: 800 Ω
(puede usarse con cargas tan bajas como 150 Ω con nivel de limitación reducido)
Voltaje en circuito abierto: –43 dBV/Pa (7,0 mV)
–18 dBV (0,13 V) mínimo
Menos del 1% a 120 dB
120 dB
98 dB
22 dB típico, ponderación A
26 dB típico, ponderación según DIN 45 405
SPL equivalente de –4 dB en un campo de 1 mOe
(60 Hz)
72 dB a SPL de 94 dB (IEC 651)
Una presión positiva en el diafragma del micrófono produce un voltaje positivo en la clavija 2 con respecto a la clavija 3 del conector del cable de salida del preamplificador
11 a 52 VCC alimentación fantasma. Protección contra inversión de polaridad
0,33 mA
Temperaturas de funcionamiento:
Temperaturas de almacenamiento:
–18 o
(0 o
–29 o
(–20 o
a 57
a 135
a 74
a 165 o C o o o
F)
C
F)
Negro de 1,27 m (4,17 pies) de largo, integral, dos conductores, blindado y terminado con conector
Miniatura tipo TA4F
Caja
Peso neto Micrófono: 16 g
Micrófono: Caja negra de plástico ABS termotratado con rejilla de acero inoxidable
P lifi d C j d b d l negro mate, gancho de sujeción color negro/cromado
Micrófono: 16 gg
Preamplificador: 118 g
* Produce un voltaje positivo en la clavija 2 del conector de tres clavijas del receptor inalámbrico Shure L4/EC4.
ACCESORIOS SUMINISTRADOS
Preamplificador (SM93) . . . . . . . . . . . . . . . . . . . . .
Paravientos negro (WL93, SM93) . . . . . . . . . . .
90A4360
RK355WS*
Conjunto de presilla para corbata color negro (WL93, SM93) . . . . . . . . . . . . . .
Conjunto de presilla doble para corbata color negro (SM93) . . . . . . . . . . . . . . . . . . . . .
Paravientos color café (WL93T)
Conjunto de presilla para corbata
. . . . . . . . . . . . .
RK354SB*
RK307DB
RK304T** color café (WL93T) . . . . . . . . . . . . . . . . . . . . .
Soporte de montaje cosido color negro (WL93, SM93)
Soporte de montaje cosido color café (WL93T)
. . . . . . . . . . . . . . . . . . 65B1733
. . . . . . . . . . . . . . . . . . . . .
RK304T**
65B1733A
Bolsa con cremallera para transporte
ACCESORIOS OPCIONALES
Interruptor de encendido/apagado en línea . . . . . . .
26A13
WA360
Califica para llevar las marcas CE. Cumple la directiva europea 89/336/EEC de compatibilidad electromagnética. Se ajusta a los criterios correspondientes de verificación y funcionamiento establecidos en la norma europea EN 55103
(1996), partes 1 y 2, para zonas residenciales (E1) y zonas de industria ligera (E2).
. . . . . . . . . . . .
* Los repuestos se suministran en conjuntos de 4 unidades.
** RK304 comprende 2 presillas para corbata y 2 paravientos.
CERTIFICACIONES
9
Microfoni lavalier SM93 e WL93
I modelli Shure WL93 e SM93 sono microfoni lavalier subminiatura omnidirezionali a condensatore a elettrete. Si appuntano facilmente sugli abiti e sono ideali per le trasmissioni televisive, le rappresentazioni teatrali e l’uso con impianti di amplificazione, grazie al loro design non appariscente e alla risposta in frequenza appositamente realizzata per impieghi di questo tipo. Entrambi i modelli presentano un piccolo elemento microfonico che fornisce un suono pieno e chiaro, comparabile a quello di microfoni molto più grandi.
Il modello WL93, studiato per l’uso con radiosistemi, va collegato direttamente a un radiotrasmettitore Shure Body-Pack.
Il modello SM93, studiato per l’uso con sistemi cablati, comprende un preamplificatore collegabile a connettori audio professionali a tre piedini (XLR), richiede alimentazione phantom e funziona a tensioni comprese tra 11 e 52 V c.c., in conformità alle norme DIN e IEC sull’alimentazione phantom. riati modi. Per ottenere una ripresa ottimale è consigliabile appuntarlo sul petto. Si ottiene un suono di alta qualità anche portando il microfono tra i capelli, attaccandolo con dei punti agli indumenti o fissandolo a uno strumento acustico, quale una chitarra.
• Fermaglio da cravatta. A molla, si aggancia facilmente alla cravatta, a un bavero, alla camicetta o alla camicia. Il microfono va fissato a scatto nella staffa di montaggio del fermaglio. Il fermaglio doppio in dotazione al modello
SM93 consente il montaggio simultaneo di due microfoni.
• Staffa a cucitura. Si cuce direttamente a un indumento
(Figura1). Usate un filo scuro o chiaro, in modo da abbinarne il colore a quello della staffa.
MICROFONO
CARATTERISTICHE
• Microfono lavalier, esecuzione subminiatura; dimensioni adatte all’uso in teatri, trasmissioni TV, applicazioni video, film e con impianti di amplificazione.
• Dispositivi di fissaggio piccoli, non appariscenti.
• Suono pieno e chiaro, comparabile a quello di microfoni più grandi.
• Risposta in frequenza ampia e regolare, con guadagno studiato per l’uso con il microfono sul petto.
• Attenuazione alle basse frequenze controllata, per ridurre il rumore della sala e degli indumenti a bassa frequenza.
• Bassa distorsione e ampia gamma dinamica.
• Diagramma polare omnidirezionale uniforme.
• Preamplificatore (SM93) agganciabile alla cintura o in vita.
• Ampio intervallo delle tensioni di alimentazione del preamplificatore di potenza (SM93).
VERSIONI
Versione Cavo
WL93
SM93
WL93–6 1,8 m
WL93T 1,2 m
Colore
Cavo e microfono marrone
WL93–6T 1,8 m marrone chiaro
COLLEGAMENTI
Collegate il connettore miniatura maschio, a quattro piedini
(TA4M) del cavo microfonico 93 al preamplificatore in dotazione (SM93) o a un radiosistema Shure Body-Pack (WL93).
NOTA: non collegate il microfono 93 direttamente a un mixer senza utilizzare il preamplificatore in dotazione o un sistema Body-Pack.
MONTAGGIO DEL MICROFONO
I fermagli per cravatte e la staffa di montaggio in dotazione al WL93 e al SM93 consentono di portare il microfono in sva-
INDUMENTO
STAFFA
FILO
MONTAGGIO A CUCITURA
FIGURA 1
MONTAGGIO DEL PREAMPLIFICATORE SM93
Usate il fermaglio da cintura, a molla, per agganciare il preamplificatore a una cintura, a una gonna o a una fascia in vita oppure all’interno di una tasca.
ANTIVENTO
L’antivento in schiuma poliuretanica in dotazione riduce il rumore indesiderato del vento quando si usa il microfono all’aperto.
ALIMENTAZIONE DEL PREAMPLIFICATORE SM93
Il preamplificatore in dotazione al modello SM93 è alimentabile con una qualsiasi sorgente di alimentazione phantom a tensione compresa tra 11 e 52 V c.c., quale l’alimentatore
Shure modello PS1A.
IMPEDENZA DEL PREAMPLIFICATORE SM93
Per ottenere gamma dinamica massima e distorsione minima, usate un’impedenza di carico uguale o maggiore di
800 Ω. Si possono utilizzare carichi inferiori, fino a 150 Ω, ma ne conseguirebbe una riduzione del livello di clipping (limitazione) in uscita. Si noti che l’alimentatore stesso può aggiungere un carico al microfono (3300 Ω nel caso del modello
Shure PS1A).
USO DI ALTRI PREAMPLIFICATORI O DI SISTEMI BO-
DY–PACK
Se collegate il microfono 93 a un apparecchio DIVERSO da un radiosistema Shure Body-Pack o dal preamplificatore in dotazione al modello SM93, accertatevi che esso generi una tensione di + 5 V c.c. regolata ( 40 mA min.) al piedino 2 del connettore del microfono, come illustrato nella figura 2.
10
DATI TECNICI
Tipo
Risposta in frequenza (Figura 3)
Diagramma polare
Impedenza di uscita
MICROFONO WL93 (con il circuito di prova standard illustrato nella figura 6)
A condensatore (polarizzazione a elettrete)
Da 50 a 20.000 Hz
Omnidirezionale, uniforme in frequenza
3000 Ω
MICROFONO SM93 (con preamplificatore)
A condensatore (polarizzazione a elettrete)
Da 80 a 20.000 Hz, attenuazione di 12 dB/ottava sotto i 100 Hz
Omnidirezionale, uniforme in frequenza
Valore nominale 150 Ω (valore effettivo 90 Ω)
Impedenza di carico minima raccomandata: 800 Ω (si può caricare il microfono con impedenze inferiori, fino a 150 Ω, con livelli inferiori di clipping).
Tensione a circuito aperto: –43 dBV/Pa (7,0 mV) Livello di uscita
(1 pascal = 94 dB di SPL)
Livello di clipping in uscita (a
1.000 Hz)
Distorsione armonica totale
Livello di pressione sonora
(SPL) max.
Gamma dinamica (SPL max. a livello di rumore misurato con filtro di ponderazione A)
Rumore di uscita (SPL equivalente)
Tensione a circuito aperto: –38 dBV/Pa
(13 mV)
0,25 V a 120 dB
Inferiore a 1% a 120 dB
120 dB
102 dB
–18 dBV (0,13 V) min.
Inferiore a 1% a 120 dB
120 dB
98 dB
Ricezione del ronzio (rumore elettromagnetico)
Rapporto segnale/rumore
Polarità
Tensione di funzionamento raccomandata
Corrente assorbita
Specifiche ambientali
Cavo
Involucro
Peso netto
18 dB (valore tipico), filtro di ponderazione A
Non pert.
76 dB a 94 dB di SPL (IEC 651)
Una pressione positiva sul diaframma produce una tensione positiva sui piedini 3 e 4 rispetto al piedino 1 (massa)*
Tra 2 e 10 V; 5 V valore nominale (tra il piedino 2 e i piedini 3 e 4)
40 mA (valore tipico)
Temperature di funzionamento: tra –18 e 57 o C
Temperature a magazzino: tra –29 e 74 o C
Nero, 1,27 m (4,17 piedi), non scollegabile, a due conduttori, schermato, dotato di connettore miniatura tipo TA4F (WL93T: marrone chiaro, 1,27 m [4,17 piedi])
Microfono: in materiale termoplastico ABS nero, con griglia di acciaio inossidabile
Microfono: 16 g
22 dB (valore tipico), filtro di ponderazione A
26 dB (valore tipico), filtro di ponderazione a norma
DIN 45 405
–4 dB di SPL equivalente in un campo di intensità pari a 1 mOe (60 Hz)
72 dB a 94 dB di SPL (IEC 651)
Una pressione positiva sul diaframma produce una tensione positiva sul piedino 2 rispetto al piedino 3 del connettore del cavo di uscita del preamplificatore
Tra 11 e 52 V c.c., alimentazione phantom. Protetto dall’applicazione di una tensione inversa.
0,33 mA
Temperature di funzionamento: tra –18 e 57 o
Temperature a magazzino: tra –29 e 74 o C
C
Nero, 1,27 m (4,17 piedi), non scollegabile, a due conduttori, schermato, dotato di connettore miniatura tipo TA4F
Microfono: in materiale termoplastico ABS nero, con griglia di acciaio inossidabile
P lifi t i l di i i fi it opaca e fermaglio da cintura nero, in cromo
Microfono: 16 gg
Preamplificatore: 118 g
* Genera una tensione positiva al piedino 2 di un connettore a tre piedini di un radioricevitore Shure L4/EC4.
ACCESSORI IN DOTAZIONE
Preamplificatore (SM93) . . . . . . . . . . . . . . . . . . . .
Antivento nero (WL93, SM93) . . . . . . . . . . . . .
Fermaglio nero da cravatta (WL93, SM93)
Fermaglio nero doppio da cravatta (SM93)
Antivento marrone chiaro (WL93T)
. .
RK355WS*
RK355WS*
. . .
. . . . . . . . .
90A4360
RK307DB
RK304T**
Fermaglio marrone chiaro da cravatta (WL93T)RK304T**
Staffa di montaggio nera a cucitura (WL93, SM93) 65B1733
Staffa di montaggio marrone chiaro a cucitura (WL93T)65
B1733A
Custodia con cerniera, adatta per il trasporto . . . . 26A13
* I ricambi sono forniti in multipli di 4.
** L’accessorio RK304 comprende 2 fermagli da cravatta e 2 antivento.
11
ACCESSORI IN OPZIONE
Interruttore di alimentazione on/off in linea . . . . . WA360
CERTIFICAZIONI
Contrassegnabile con il marchio CE. Conforme alla direttiva europea sulla compatibilità elettromagnetica
89/336/CEE. Conforme ai criteri sulle prestazioni e alle prove pertinenti specificati nella norma europea EN 55103
(1996) parti 1 e 2, per ambienti residenziali (E1) e industriali leggeri (E2).
SM93
+10
0
–10
BLINDAJE
SCHERMATURA
SCHÉMA DE CÂBLAGE DU MICROPHONE
MIKROFONSCHALTPLAN
DIAGRAMA DE ALAMBRADO DEL MICROFONO
SCHEMA CIRCUITALE DEL MICROFONO
FIGURE 2
20 50 100 200 500 1,000 2,000
Hz
5,000 10,000 20,000
RÉPONSE EN FRÉQUENCE TYPIQUE
TYPISCHER FREQUENZGANG
RESPUESTA DE FRECUENCIA TIPICA
RISPOSTA IN FREQUENZA TIPICA
FIGURE 3
27 mm
(1–1/16 IN.)
98.8 mm
(3–29/32 IN.)
Á Á ÁÁÁÁ ÁÁÁÁ Á
ÁÁ Á Á ÁÁÁÁ ÁÁ Á ÁÁÁÁ Á Á Á ÁÁ Á Á ÁÁ Á ÁÁ Á Á
18.8 mm
(3/4 IN.)
ÁÁ ÁÁ Á ÁÁ Á Á ÁÁ Á Á Á Á Á Á Á Á ÁÁ Á Á Á Á Á Á Á Á Á Á ÁÁ Á Á Á ÁÁ Á ÁÁ Á Á Á Á Á Á ÁÁÁÁ ÁÁÁÁ Á Á Á Á Á ÁÁ Á
Á Á ÁÁ Á Á Á Á Á Á Á Á Á ÁÁ Á ÁÁ ÁÁ Á Á Á ÁÁ Á ÁÁ Á Á Á Á Á
0.37 IN
(9.40 mm)
0.15 IN.
(3.81 mm)
0.23 IN.
(5.84 mm)
0.24 IN.
(6.10 mm)
SM93 PREAMPLIFIER SM93/WL93 MICROPHONE
DIMENSIONS HORS TOUT S GESAMTABMESSUNGEN S DIMENSIONES GENERALES S DIMENSIONI COMPLESSIVE
FIGURE 4
C
D1
P2
RED C3
33X6.3
R4
360K
4.1V
86B429
1
4
3
2
BLK
.1V
B
1.9V
C7
.047,5% .6V
R2
33K
Q2
86A350
3.5V
P1
C6
.047,5% R5
62K
C5
150 pF
R1
Q1
86A348
.1V
.05V
D2
86A415
2
3
1
C8
150 pF
R6
24K
L1
2
GRN A
C1
150 pF
1
NOTES:
1. ALL RESISTORS 5%,1/8 WATT, UNLESS OTHERWISE SPECIFIED.
WHT BLK GRN YEL
C2
150 pF
BRN
L2
3
2. ALL NON–POLAR CAPACITORS IN µ F, TOLERANCE 10% AND 50 VOLTS OR MORE
UNLESS OTHERWISE SPECIFIED. POLARIZED CAPACITORS SHOWN IN µ F x VOLTS.
3. D.C. VOLTAGES MEASURED WITH 11 MEG INPUT VOLTMETER; A.C. VOLTAGE MEA-
SURED WITH 1 MEG INPUT VOLTMETER. VALUES SHOWN ARE TYPICAL AND MAY
VARY ± 20%.
4. THE FOLLOWING SYMBOLS DENOTE:
CIRCUIT BOARD GROUND
CASE GROUND
A.C. VOLTAGE
D.C. VOLTAGE
.05V
T1 6. INPUT SIGNAL OF 0.1V AT 2 KHZ
APPLIED TO CIRCUIT BELOW:
18K
C
10x10
5. POWER SOURCE IS 21 VDC THROUGH TWO 1.691 KOHM, 1% RESISTORS FROM
SUPPLY TO PINS 2 AND 3 OF CONNECTOR P1.
B
.1V
1.2K
A
SCHÉMA DE PRINCIPE DU PRÉAMPLIFICATEUR SM93 S STROMLAUFPLAN FÜR VORVERSTÄRKER SM93 S DIAGRAMA
ESQUEMATICO DEL PREAMPLIFICADOR SM93 S SCHEMA CIRCUITALE DEI MODELLI DEL PREAMPLIFICATORE SM93
FIGURE 5
2.2 mF
V out
1
4
2
3
20 K
+5V
CIRCUIT D’ESSAI S PRÜFSCHALTUNG S CIRCUITO DE
PRUEBA S CIRCUITO DI PROVA
FIGURE 6
SHURE Incorporated Web Address: http://www.shure.com
5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.
Phone: 800-257-4873 Fax: 847-600-1212
In Europe, Phone: 49-7131-72140 Fax: 49-7131-721414
In Asia, Phone: 852-2893-4290 Fax: 852-2893-4055
Elsewhere, Phone: 847-600-2000 Fax: 847-600-8446
12
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project