Silex technology | SDZ-330 | User's Manual | Silex technology SDZ-330 User's Manual

Silex technology SDZ-330 User's Manual
SALES NETWORK
SAMSUNG TECHWIN CO., LTD.
145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si,
Gyeonggi-do 462-703, Korea
TEL : +82-31-740-8137~8141 FAX : +82-31-740-8145
• SAMSUNG OPTO-ELECTRONICS AMERICA,INC.
ELECTRONIC IMAGING DIV.
40 Seaview Drive, Secaucus, NJ 07094, U.S.A
TEL : +1-201-902-0347 FAX : +1-201-902-0429
• SAMSUNG TECHWIN MOSCOW OFFICE
Korp 14, 37-A, PR-KT, Lenningradsky, Moscow 125167, Russia
TEL : +7-95-258-9296,9298 FAX : +7-95-258-9297
•
www.samsungtechwin.com
www.samsungcctv.com
SAMSUNG OPTO-ELECTRONICS UK, LTD.
Samsung House, 1000 Hillswood Drive, Hillswood Business
Park Chertsey, Surrey KT16 OPS
TEL : +44-1932-45-5308 FAX : +44-1932-45-5325
• TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD.
7 Pingchang Rd, Nankai Dist. Tianjin 300190, P.R China
TEL : +86-22-2761-4724(33821) FAX : +86-22-2761-6514
•
P/No. : Z6806-0618-01B
VAN 05. 09
High Sensitivity, Day & Night
30X Zoom Color Camera
INSTRUCTION MANUAL
SDZ-330
About this manual
Please read this manual carefully before installing and using the camera. Be sure to keep the manual handy for later reference.
The lightning flash with an arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
INFORMATION -This equipment has been tested and found to comply with limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at
his own expense.
WARNING - Changes or modifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
CAUTION : To prevent electric shock and risk of fire hazards:
Do NOT use power sources other than that specified.
Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualified service person and
should conform to all local codes.
Features
Warning
The camera requires regular maintenance.
30x Optical Zoom
Day & Night
Contact an authorized technician for maintenance and/or servicing.
The built-in SDZ-330 optical zoom lens is a
highly durable component. It features auto
focus, auto iris, and zoom functions.
The camera automatically determines whether
it is night time or day time, selecting operating
mode automatically. The camera operates in
color mode during day light conditions and BW
mode in night conditions for clearer identification.
Do not continue to use if malfunctioning.
SV-III DSP Chip
SDZ-330 features a powerful DSP that can
efficiently remove image noise, producing
crisp and clear images even under low
lighting conditions.
Fine Picture Quality under Ultra Low
Lighting
The integrated SV-III DSP Chip and 1/4" high
density CCD allows the user to capture
bright, high-quality images under ultra low
lighting conditions.
- 0.4 Lux in normal color mode.
Wide Dynamic Range (WDR)
The WDR feature offers powerful compensation
performance and thus allows for crisp, clear,
and perfect light contract under any environment.
High Resolution
Featuring 520TV line horizontal resolution in
color mode and 570TV line horizontal resolution
in BW mode, the camera features Sony's
Double Speed 410,000 pixel CCD and captures
clean, noiseless, high-quality images.
Prolonged use of the camera in abnormal operating conditions (produces
smoke, overheats, etc.) may result in a fire.
Do not Install the camera on a surface that can not support it.
Motion Detection
Installation on an unsuitable surface may cause the camera to fall and/or other hazards.
Once motion is detected, the camera sends
an alert signal to the processing unit, which, if
used in conjunction with an optional alarm,
can provide effective surveillance of your
property.
Do not handle the power cable with wet hands.
May result in an electric shock.
Do not disassemble the camera.
May result in a fire, electric shock, and/or other hazards.
Miscellaneous Functions
Other miscellaneous functions of the camera
include privacy zone masking, digital zoom, line
lock synchronization (INT/LL), freeze,
horizontal inversion, and user-configured
presets.
Control via OSD Menu and RS485
The OSD menu and RS-485 pins allow for
remote control of the camera.
The user can also directly control the lens
using external control connection.
Do not place the camera in the vicinity of inflammables.
May result in a fire and/or other hazards.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems) This marking shown on the product or its
literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, please
separate this from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources. Household users should contact either the
retailer where they purchased this product, or their local government office, for
details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions
of the purchase contract. This product should not be mixed with other commercial
wastes for disposal.
Contents
8
Precautions
• CAM TITLE
18
18
19
20
• WHITE BALANCE
23
• BACKLIGHT
24
25
27
Operating Your Camera
Menu Configuration
Menu Setup
10
Components and Accessories
11
11
12
13
Overview
Top
Bottom
Back
• MOTION DETECTION
• FOCUS
31
36
• EXPOSURE
• SPECIAL
43
43
• RESET
• EXIT
14
Connection
14
15
16
Connecting To Monitor
Connecting To Power
Connecting To Connection
COLOR CCD CAMERA
6
User’s Manual
Troubleshooting
44
Specification
46
Protocol Command Descripition
48
COLOR CCD CAMERA
7
User’s Manual
Precautions
Do not install under extreme
temperature conditions.
Do not install in high humidity
environment.
Use only under temperature conditions
between -10˚C and +50˚C. Provide good
ventilation when using in high temperature
conditions.
Do not install under unstable
lighting conditions.
May lower image quality.
Do not drop the camera or
subject it to physical shock.
May cause a product malfunction.
Never keep the camera face to
strong light directly.
May damage the CCD.
Do not expose the camera to
rain or other types of liquids.
Do not expose the camera to
radioactivity.
Avoid touching the camera lens.
Wipe dry any liquids. Liquids may contain
minerals that are corrosive to electronic
components.
Radioactivity exposure may damage the
CCD.
Notes
Severe lighting changes or flickering may
hinder normal camera operation.
COLOR CCD CAMERA
8
The lens is the most important component
of the camera. Be careful not to smear it
with fingerprints.
User’s Manual
• Exposure to a spotlight or an object emitting strong light may cause smear or
blooming.
• Ensure that the power source complies with normal specifications before supplying
it to the camera.
COLOR CCD CAMERA
9
User’s Manual
Components and Accessories
Overview
Top
1. 30x Zoom Color Camera
SDZ-330
Close
2. Instruction Manual
3. 6-Pin Connection Cable
Open
Tripod Mounting Bracket Screw Hole
Used to fix tripod mounting bracket on top of the camera.
Front Cover Ring
Removable for replacement with a filter.
4. Front Cover Ring
5. Remote Controller (Optional)
COLOR CCD CAMERA
10 User’s Manual
COLOR CCD CAMERA
11 User’s Manual
Overview
Bottom
Back
Tripod Mounting Hole
Used to install the camera on an optional tripod.
The tripod must be equipped with screws with
specifications shown on the right.
L
1/4"-20 UNC (20 THREAD)
L:4.5mm±0.2mm (ISO standard),
or 0.197" (ASA standard)
Key Buttons
· Following buttons control zoom, focus, and auto focus functions.
WIDE button : To widen the view. (ZOOM OUT)
TELE button : To close in on a far object. (ZOOM IN)
F-NEAR button : To see a near object clearly.
F-FAR button : To see a far object clearly.
AF button
: To activate auto focus just once.
Pressing the 'SET' button locks the zoom control function of these buttons and
prompts the main setup menu.
Notes
• The zoom postion is saved after 5 seconds when you set zoom function.
Attach the bracket to the top of the camera. Use screws
included in the package or their equivalent (less than
6mm). Otherwise, the bracket may not assemble to the
camera properly.
COLOR CCD CAMERA
12 User’s Manual
· Main setup menu can be navigated using these buttons.
SET : To access the main setup menu.
UP (WIDE button)
: To move the arrow indicator to up.
DOWN (TELE button) : To move the arrow indicator to down.
LEFT (F-NEAR button) : To move the arrow indicator to left.
RIGHT (F-FAR button) : To move the arrow indicator to right.
COLOR CCD CAMERA
13 User’s Manual
Overview
External Control Connector
Relates to the motion detection output signal.
Zoom and focus functions can be controlled using external siganals.
Power LED
Illuminates when power is supplied.
Video Output Jack
Used to connect an external video monitor in jack.
Communication Control Connector
Used to connect the Remote Controller (Optional). Includes external 'SYNC' signal
input pin, which is used for the line lock function.
Includes the RS-485 communication pin.
Power Input Terminal
Power supply terminal (DC12V±10%).
Frame Ground Terminal
It is the GND terminal of the motion detection signal.
• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate
device.
CCD Camera
Intermediate
End monitor
Connecting to Power
Connect the power cable to the camera's Power In as shown in the figure
below.
Connection
Connecting to Monitor
Power Input Terminal
Connect Video Out Jack to the monitor's Video In jack as shown below.
CCD Camera
Monitor
Frame Ground
Notes
• Connection methods may vary depending on the video equipment. Please
refer to the model specific instruction manual.
• Connect cables with the unit powered down.
COLOR CCD CAMERA
14 User’s Manual
• Connect the power once the installation is complete.
• The wire is polarized. Match '+' and '-' terminals properly.
• Use a DC12V/500mA power source for SDZ-330.
COLOR CCD CAMERA
15 User’s Manual
Connection
Connecting to connection
External Control Connector
FOCUS (Input)
ZOOM (Input)
COM
MD (output)
Function
Connector
Signal Level
Tele
ZOOM
COM
Wide
I
Number
Name
Description
Number
Name
Description
1
GND
-
4
TRX +
RS-485 Communication
5
TRX -
RS-485 Communication
6
Output Power
Remote Controller only
I
COM
COM
5±0.5sec
* Communication Control Connector Pin Description .
+6V~+12V
COM
0V
There is no motion
6-Pin Connection
Cable
Remote Controller
SCC-100, SDZ-160CO
COM
-6V~-12V
Near
MD
SCC-3000
COM
-6V~-12V
Far
FOCUS
I/O
+6V~+12V
+4.0V~+5.0V
There is motion
2
3
EXT.SYNC External ‘SYNC’ Signal
GND
-
3V or 5V
* EXT. SYNC
-
0V
Min: 500ns
60Hz ± 0.1Hz(NTSC), 50Hz ± 0.1Hz(PAL)
O
* MD (Motion Detection) Output Signal Level (less than 10mA)
* When using the MD function, the 'GND' should be connected to the frame ground.
Communication Control Connector
The camera can be controlled by using external controllers like a Remote
controller. (RS485 Communication)
* Communication Setting can set the communication setting as shown in the table below.
When you use to connect SCC-100 or SCC-3000, the default sets for SCC-100.
ITEM
MODE
Data Bit
Bit/Sec
Parity
CAM ID NO.
RETURN PACKET
SCC-100
Serial
8 bit
9600bps
EVEN
0
ENABLE
Notes
• Contact an authorized technician for inspection.
COLOR CCD CAMERA
16 User’s Manual
COLOR CCD CAMERA
17 User’s Manual
SCC-3000
Serial
8 bit
9600bps
NON
1~255
See the SCC-3000 settigs
Operating Your Camera
Menu Configuration
MAIN SETUP
MENU
Menu Setup
Use the six buttons on back of the camera.
CAM TITLE
• OFF
• ON
UP button
SET button
WHITE BAL.
• ATW
• AWC
BACKLIGHT
• OFF
• WDR
MOTION DET.
• OFF
• ON
• MANUAL
FOCUS
• MODE
• ZOOM TRK MODE
• ZOOM TRK SPD • D-ZOOM
• DISP ZOOM MAG
• ZOOM INIT POS • LENS INIT
• END
EXPOSURE
• BRIGHTENESS
• AGC
• END
• IRIS
• SSNR
• SHUTTER
• SENS-UP
SPECIAL
• USER PRESET
• SYNC
• V-REV
• END
• PRIVACY
• FREEZE
• IMAGE ADJ
• DAY/NIGHT
• H-REV
• COMMUNICATION
RESET
EXIT
COLOR CCD CAMERA
18 User’s Manual
LEFT button
AF button
DOWN button
RIGHT button
1. Press the SET button to access the main setup mode.
• Main setup menu is displayed on the monitor screen.
2. Select the desired feature using the UP or DOWN button.
• Each pressing of the UP or DOWN button moves the indicator to the next
or previous feature.
• Move the arrow indicator to the desired feature item.
COLOR CCD CAMERA
19 User’s Manual
Operating Your Camera
3. Press SET button.
Change the status using the
LEFT or RIGHT button.
Select feature using the UP
or DOWN button.
3. Change the status of the selected feature using the LEFT or RIGHT button.
4. When completed, move the arrow indicator to 'EXIT' and press the SET button.
Notes
• Features marked with a have an accessible submenu.
• Access the submenu by pressing the SET button.
4. You can enter up to 20 characters.
Move the cursor to the character entry field using the LEFT or RIGHT
button.
Use UP, DOWN, LEFT, and RIGHT buttons to select a desired character.
Cam Title
Use this feature to designate a name for the camera, which will display on the
monitor screen.
1. Press the SET button to display the main setup menu and move the arrow
indicator to 'CAM TITLE' using the UP or DOWN button.
2. Set 'CAM TITLE' to 'ON' using the LEFT or RIGHT button.
Notes
• If the CAM TITLE feature is set to 'OFF',
the name will not displayed in the monitor.
Press the SET button to confirm selection of the blinking character. The
character is then saved, and the cursor in the entry field moves to the
next position.
Repeat steps through until the desired name has been entered.
Notes
• Correcting Mistakes
Move the cursor to 'CLR' and press the SET button to clear the entire entry.
To modify one character, use or to position the cursor above the character
to be modified and click the SET button after selecting the character to enter.
COLOR CCD CAMERA
20 User’s Manual
COLOR CCD CAMERA
21 User’s Manual
Operating Your Camera
5. Select on screen position of the CAM TITLE.
Move the cursor to 'POS' and press SET button.
White Balance Control
Your camera provides three 'WHITE BAL' control modes for your choosing in
adjusting the white balance.
1. Press the SET button to access the main setup menu and move the indicator
to 'WHITE BAL' using the UP or DOWN button.
2. Set 'WHITE BAL' using the LEFT or RIGHT button.
The CAM TITLE is displayed on the top-left of the monitor screen.
(Default position)
FRONT DOOR
to Locate, then SET
The three white balance control modes are as follows :
Select the position by using the 4-directional buttons, then press the SET
button to confirm the position.
FRONT DOOR
to Locate, then SET
6. When completed, move the cursor to 'END' and press SET button.
COLOR CCD CAMERA
22 User’s Manual
ATW (Auto Tracking White Balance): When color temperature is 1800 ~ 10500˚K,
select this mode.
AWC (Auto White balance Control): The white balance is automatically
adjusted in a specific environment. In order to obtain the best result, press
the SET button while the camera focuses on white paper. If the environment
including the light source is changed, you have to adjust the white balance
again.
Manual: To fine adjust, select the Manual mode. You can increase or decrease
the red or blue factor while monitoring the difference on the screen. Set
to 'MANUAL' mode and press the SET button. Increase or decrease the
value for red(R-Gain) and blue(B-Gain), watching the color of the picture,
and press the SET button when you obtain the best color.
COLOR CCD CAMERA
23 User’s Manual
Operating Your Camera
Notes
• Proper White Balance may not be obtained under the following conditions.
When the scene contains mostly high color temperature object, such as a blue
sky or sunset.
When the scene is dim.
If your camera directly faces a fluorescent lamp or is used in an environment of
varying lighting conditions.
3. Select the ' WDR' mode and Press the SET button
•You can adjust the LIMIT for WDR
You can select the level(LOW,MIDDLE,HIGH). WDR sensitivity is increased or decreased.
4. When completed, press the SET button.
Notes
Backlight
The built-in SVIII DSP chip provides intelligent light level control to overcome the
severe ‘BACKLIGHT’ conditions.
1. Press the SET button to display the main setup menu and move the arrow
indicator to ‘BACKLIGHT’ using the UP or DOWN button.
2. SET ‘BACKLIGHT’ to the desired mode using the LEFT or RIGHT button.
WDR: Compensates for scenes simultaneously containing bright and dark elements.
OFF: Deactivation
• The WDR mode cannot be used if 'Shutter of Exposure Menu' is set to
'MANUAL'.
• The following phenomenon may occur when operating under the WDR mode. In
such event, do not continue use under the WDR mode.
Unnatural color change or screen phenomenon.
Screen noise on bright elements.
• WDR performance vary on bright on screen elements. Adjust the camera angle
accordingly when installing the camera to compensate.
• Making changes to the WDR LIMIT may result in unnatural screen phenomenon.
Motion Detection
alert signal upon detecting motion. When used in conjunction with an external
alarm, the user can receive MD alerts. This feature is useful when monitoring
several screens simultaneously.
1. Press the SET button to access the main setup menu and move the indicator
to 'MOTION DET' using the UP or DOWN button.
2. Set 'MOTION DET' to ON using the LEFT or RIGHT button.
WDR
COLOR CCD CAMERA
OFF
24 User’s Manual
COLOR CCD CAMERA
25 User’s Manual
Operating Your Camera
FOCUS
Press the SET button.
Increase or decrease detection sensitivity by setting the 'SENSITIVITY' value.
· When completed, press SET button.
Notes
Tips on Using the Motion Detection Feature
• Once the sensitivity level has been set, perform a test to verify proper operation
of the feature.
• The feature may not function properly under flickering light conditions.
• The camera interprets sudden changes in lighting and subsequent change in
brightness of an object as motion.
• With the feature enabled, other algorithms may require additional time to operate
than usual.
• This system does not guarantee prevention of fire or theft.
The manufacturer shall not be held responsible for any
accident or damage incurred.
• Connect an external alarm device to MD Out on back of
the camera.
COLOR CCD CAMERA
26 User’s Manual
1. Press the SET button to access the main setup manu and then position the
indicator over FOCUS using the UP or DOWN button.
2. Press the SET button.
MODE: You can select the most suitable zoom mode. Move the arrow indicator to
‘MODE’ using UP or DOWN button.
•AUTO : Select AUTO and press the SET button to confirm. Increase or decrease
optical zoom (ZOOM) or digital zoom (DZOOM) positions using the UP or DOWN
button while verifying the changes on screen.
Enabling D-ZOOM (ON) means that digital
zoom will activate once optical zoom ends.
Focus is automatically adjusted with moving
zoom.
COLOR CCD CAMERA
27 User’s Manual
Operating Your Camera
•ONE PUSH : Focus is automatically adjusted just once,
after zoom position is changed. Select '
ONE PUSH' and press the SET button to
confirm. Increase or decrease optical
zoom (ZOOM) or digital zoom (D-ZOOM)
positions using the directional buttons
while verifying the changes on screen. Press the SET button once
desired image quality is obtained.
•MANUAL : Select 'MANUAL' and press the SET button
to confirm. Increase or decrease optical zoom
(ZOOM) or digital zoom (D-ZOOM) positions
using the directional buttons while verifying
the changes on screen. Press the SET button
once desired image quality is obtained. Focus
can be manually adjusted, independent of moving zoom.
ZOOM TRK MODE: You can select to use ‘ZOOM TRK MODE’. Move the arrow
indicator to ‘ZOOM TRK MODE’ using UP or DOWN button. Set
‘ZOOM TRK MODE’ to on using LEFT or RIGHT button.
ZOOM TRK SPD: Configure zoom tracing speed using this feature. Position the
indicator over 'ZOOM TRK SPEED' using the UP or DOWN button
and then set to desired mode using the LEFT or RIGHT button.
COLOR CCD CAMERA
28 User’s Manual
•FAST: To move zoom fast.
•SLOW: To move zoom slowly.
Notes
• The 'ZOOM TRK SPEED' mode cannot be used if 'MODE' is set to 'AUTO' and
'ZOOM TRK MODE' is 'ON'.
D-ZOOM: Configure magnification limit from x1, x2, x4, or x8 using this feature.
Position the indicator over 'D-ZOOM' using the UP or DOWN button. Set 'DZOOM' to 'ON' and press the SET button to confirm.
· Set 'ZOOM LIMIT' to the desired level using the LEFT or
RIGHT button.
DISP ZOOM MAG: Use this feature to display the current zoom magnification level on
screen. Position the indicator over 'DISP ZOOM MAG' using the UP
or DOWN button. Then set to ON using the LEFT or RIGHT button.
COLOR CCD CAMERA
29 User’s Manual
Operating Your Camera
ZOOM INIT POS: Moves to the controlled ZOOM position when the power truned
on and is a function of the initial ZOOM position control.
END: To revert to the main setup menu.
EXPOSURE
LENS INIT : Use this feature to initialize the lens. Position the indicator over LENS
INIT. using the UP or DOWN button. Press the SET button to confirm.
COLOR CCD CAMERA
30 User’s Manual
1. Press the SET button to access the main setup menu and then position the
indicator over 'EXPOSURE' using the UP or DOWN button.
2. Press the SET button to confirm.
BRIGHTNESS: Use this feature to adjust image brightness. Position the
indicator over 'BRIGHTNESS' using the UP or DOWN button.
Then increase or decrease brightness level using the LEFT or
RIGHT button while verifying the changes on screen. Set END
once desired level is obtained.
COLOR CCD CAMERA
31 User’s Manual
Operating Your Camera
IRIS: Set 'IRIS' to 'AUTO' or 'MANUAL'. Position the indicator over 'IRIS' using the UP
or DOWN button and then select the desired iris mode using the LEFT or RIGHT
button.
•AUTO: The iris is automatically activated upon illumination.
•MANUAL: Manual iris configuration. Set 'IRIS' to 'MANUAL' using the LEFT or
RIGHT button and then press the SET button. Increase or decrease iris
level using the LEFT or RIGHT button while verifying the changes on screen.
•A.FLK (NTSC: 1/100, PAL: 1/120): Flicker-free mode
•ESC: Automatic shutter speed setting (optimal)
•MANUAL: Manual shutter speed setting
2. If you choose ‘MANUAL’, select the optimal shutter speed.
· In MANUAL mode, the optimal shutter speed needs to be designated. Select from 1/60
to 1/120,000 (NTSC) or from 1/50 to 1/120,000 (PAL).
* 'Sens-Up' mode can be configured manually (2x to 128x).
· Verify changes made to the shutter speed by referencing to changes in on screen
brightness.
3. Press the SET button to complete.
Notes
SHUTTER : Control image brightness by adjusting shutter speed.
1. Position the indicator over 'SHUTTER' using the UP or DOWN button. Then select
the desired shutter mode (A.FLK, ESC, MANUAL) using the LEFT or RIGHT button.
COLOR CCD CAMERA
32 User’s Manual
• Set the 'WDR' mode under the Backlight menu to OFF for maximum A.FLK
performance. 'A.FLK' will not function properly otherwise.
• Image may become unstable if the camera is set to 'ESC' mode and faces a strong
fluorescent light.
• Under 'ESC' mode, the brightness can be adjusted using the LEFT or RIGHT button.
• The WDR feature is not available under MANUAL mode.
• Sens-up is disabled under 'MANUAL' or 'A.FLK' mode.
COLOR CCD CAMERA
33 User’s Manual
Operating Your Camera
AGC (Auto Gain Control): For brighter images.
1. Position the indicator over 'AGC' using the UP or DOWN button.
2. Set 'AGC' to the desired mode using the LEFT or RIGHT button.
•HIGH
: Wide range gain value adjustment
•MIDDLE : Middle range gain value adjustment
•LOW
: Narrow range gain value adjustment
•OFF
: Disabled
Notes
• Changing 'AGC' setting from LOW to HIGH results in greater sensitivity, as well as
on screen noise.
• Setting 'AGC' to OFF locks 'SSNR' configuration.
SENS-UP : This feature ensures clear images at night or under low lighting
conditions.
1. Position the indicator over 'SENS-UP' using the UP or DOWN button.
2. Set 'SENS-UP' to the desired mode using the LEFT or RIGHT button.
•AUTO : Select this mode for use in night time or under low lighting conditions.
•OFF : Disabled
SSNR(Samsung Super Noise Reduction): On screen noise reduction.
1. Position the indicator over 'SSNR' using the UP or DOWN button.
2. Set 'SSNR' to the desired mode using the LEFT or RIGHT button.
•LOW : Low noise reduction
•MIDDLE : Medium noise reduction
•HIGH : High noise reduction
•OFF
: Disabled
Notes
• Once 'AUTO' mode is set, the user can configure Sens-Up limit by increasing
/decreasing the shutter speed (e.g.: x2,...,x32, x64,..., x128).
• Enabling Sens-Up increases camera sensitivity and may result in additional noise
and/or other phenomenons. This is normal.
COLOR CCD CAMERA
34 User’s Manual
COLOR CCD CAMERA
35 User’s Manual
Operating Your Camera
•PRESET NO : Up to eight different preset configurations are supported.
SPECIAL
•PRESET MODE: Configure initial settings under FOCUS, EXPOSURE, etc.
1. Press the SET button to access the main setup menu and then position the
indicator over 'SPECIAL' using the UP or DOWN button.
2. Press the SET button to confirm.
USER PRESET: Preset user-designated configurations using this feature. Position
the indicator over 'USER PRESET' using the UP or DOWN button
and then set to 'ON' using the LEFT or RIGHT button. Press the
SET button to confirm.
COLOR CCD CAMERA
36 User’s Manual
COLOR CCD CAMERA
37 User’s Manual
Operating Your Camera
•PRESET SAVE: Save configured preset.
PRIVACY: Mask privacy area using this feature. The mask area expand/contract
upon the zoom position.
•PRESET CLEAR: Clear configured preset.
•GROUP SEL : Choose up to four groups. Each group can consist of eight mask
areas.
•MASK COLOR : Select desired mask color(BLACK, BLUE, GREEN, WHITE).
•AREA SEL
: Configure eight mask areas.
•AREA MODE : Mask area display.
•TOP
: To move the mask area up.
•BOTTOM
: To move the mask area down.
•LEFT
: To move the mask area left.
•RIGHT
: To move the mask area right.
•END: Revert to the SPECIAL SETUP menu.
COLOR CCD CAMERA
38 User’s Manual
COLOR CCD CAMERA
39 User’s Manual
Operating Your Camera
DAY/NIGHT: Select from COLOR, BW or AUTO modes.
Notes
• For NTSC models, the line-lock mode can be used if the external SYNC signal
frequency is at 60Hz.
• For PAL models, the line-lock mode can be used if the external SYNC signal
frequency is at 50Hz.
•COLOR : Color mode.
•B/W : BW mode.
•AUTO : The camera automatically detects lighting conditions and selects the mode
accordingly.
FREEZE: Use this feature to freeze capture an image. Position the indicator over 'FREEZE'
using the UP or DOWN button and then set to 'ON' using the LEFT or RIGHT
button. Press the SET button to confirm.
SYNC : Two synchronization modes are available INTERNAL and EXTERNAL LINE-LOCK.
In LINE-LOCK mode, it synchronizes the camera’s video out signal to the external
SYNC signal.
H-REV: Use this feature to horizontally inverse the screen. Position the indicator over
'H-REV' using the UP or DOWN button and then set to ON using the LEFT or
RIGHT button. Press the SET button to confirm.
•INT : Internal synchronization
•LL : External line-lock synchronization
· If you choose ‘LL’, you can adjust the desired phase.
Press the SET button.
· You can adjust the desired phase from 0 to 359.
COLOR CCD CAMERA
40 User’s Manual
COLOR CCD CAMERA
41 User’s Manual
Operating Your Camera
V-REV: Use this feature to vertically inverse the screen. Position the indicator over
'V-REV' using the UP or DOWN button and then set to 'ON' using the LEFT
or RIGHT button. Press the SET button to confirm.
•CAM ID NO. : Assign an ID number to the camera (1 to 255).
Identification number zero is used for Remote controller setup.
•CAM ID DISP: Displays camera ID on top left corner of the screen.
•BAUD RATE : Configure baud rate from 9600, 19200, or 38400bps.
•UART MODE : Configure parity bit to NON, EVEN, or ODD. Data bit is set to 8bit,
and stop bit to 1bit. Set the UART MODE to EVEN if using the Remote
Controller.
•RETURN PACKET : Used to transfer a packet.
END: evert back to the USER PRESET menu.
IMAGE ADJ: Includes image quality or special function factors.
•TONE
: Increasing this value increases the overall brightness.
•SHARPNESS : Increasing this value sharpens object edges. Too high of a setting,
however, produces noise and may obscure the image.
•COLOR
: Adjusting this value affects the chroma level only; the burst level is
unaffected.
RESET
To reset your camera to factory default condition.
EXIT
To finish setup menu.
COMMUNICATION: Use this feature to select communication protocol (refer to p.48~
p.53 for details). Position the indicator over 'COMMUNICATION'
using the UP or DOWN button.
COLOR CCD CAMERA
42 User’s Manual
COLOR CCD CAMERA
43 User’s Manual
Troubleshooting
Refer to the following table if you are experiencing trouble with your camera.
Contact an authorized technician if the table does not provide you with a
solution to the trouble.
Problem
Flickering
• The camera may be facing the sun or a fluorescent
light. Adjust the position of the camera.
Can't select LL mode
• The camera may be connected to a DC power
source. Connect to an AC power source.
LL is not function
properly.
• Check external SYNC signal frequency (should be
60Hz for NTSC, 50Hz for PAL).
Solution
• Check the power cable and the wiring between the
camera and the monitor.
• Ensure proper video cable connection (Video Out
Jack).
No display
Dim display
• The lens could be dirty. Clean with a soft, clean
piece of cloth.
• Adjust monitor settings.
• Adjust camera position if exposed to a strong light
source.
Dark display
• Adjust the monitor's contrast level.
• Set the intermediate device, if in use, to 75Ω/ Hi-z
(refer to p.15).
The camera is not
functioning properly and
its surface is hot
• Check the power source for compliance with
specifications.
Motion Detection
feature is not active.
• Ensure that the feature is set to ON.
• Check the SENSITIVITY level.
Uneven colors
• Adjust and configure WHITE BAL.
COLOR CCD CAMERA
44 User’s Manual
Solution
Problem
COLOR CCD CAMERA
45 User’s Manual
Specifications
NTSC (SDZ-330N)
P
O
W
E
R
C
C
D
O
P
T
I
C
S
S
y
n
c.
E
L
E
C
T
R
I
C
A
L
Input Voltage
Input Current
Power Consumption
Size
Total Pixels
Effective Pixels
Optics
Min. Focus Distance
D. ZOOM
Angle Field of view
Scanning System
Synchronization
Frequency
Camera Title
Camera ID
Resolution
Video Output
S/N (Y signal)
Min. Illumination
WDR
Day & Night
Gain Control
White Balance
Electronic shutter speed
O.S.D
Motion Detection
SSNR
Focus
Zoom Movement Speed
Lens Initialize
Preset
Privacy Function
PAL (SDZ-330P)
DC12V (±10%)
300 mA : Steady-state
450 mA : Max. (Zoom,Focus, Day&night motor operating)
3.6 W : Steady-state
1/4 inch, Vertical double density interline CCD
811(H) x 508(V)
795(H) x 596(V)
768(H) x 494(V)
752(H) x 582(V)
30X, f=3.3 to 99.0mm (F 1.6 to 3.2)
1000mm
X2, X4, X8
H : Appr. 58.0˚(Wide) to 2.22˚(Tele) V : Appr. 44.8˚(Wide) to 1.68˚(Tele)
2:1 Interlace
Internal / Line Lock
Horizontal:15.734 KHz/Vertical :59.94 Hz Horizontal: 15.625 KHz/Vertical : 50.00 Hz
ON/OFF (Displayed 20 characters)
255 ID Selectable
520 TV Lines(Min.) : Color 570 TV Lines(Min.) : B/W
CVBS : 1.0Vp-p/75Ω
50 dB (AGC Off, Weight ON)
0.4Lux : Color 0.08Lux : B/W
52dB
AUTO/MANUAL(COLOR, B/W) (ICR type)
Low, Middle, High,OFF Selectable
ATW/AWC/Manual (1800 ˚K ~ 10,500˚K)
AUTO/MANUAL (X128 ~ 1/60sec ~ 1/120,000sec)
Sens-up Limit is selectable
NTSC (SDZ-330N)
E
L
E
C
T
R
I
C
A
L
FLIP
FREEZE
IRIS Control
Control Output
Operating Temperature/Humidity
Storge Temperature/Humidity
Dimension
Weight
Option
RS-485(9,600bps, 19,200bps, 384,000bps Seclectable)
/ External Control by Voltage(ZOOM,FOCUS)
-10˚C to +50˚C / 20% to 80% RH
-20˚C to +60˚C / 20% to 95% RH
67.4(W) x 67.6(H) x 120(D)mm (Without Tripod Base)
450g
Remote Controller(RS-485 type)
AUTO/MANUAL (X128 ~1/50sec ~ 1/120,000sec)
Sens-up Limit is selectable
Built-In
ON/OFF (output via Terminal)
Low, Middle, High,Off
Auto / Manual / One Push
5.2 Sec : Wide to Tele
5.4 Sec : Wide to Tele
Built-In
8-Positions
ON/OFF(32 Programmable Zone/ 8 Programmable Zone per Screen)
COLOR CCD CAMERA
46 User’s Manual
PAL (SDZ-330P)
LEFT/RIGHT, UP/DOWN
On/Off
Auto/Manual
COLOR CCD CAMERA
47 User’s Manual
Protocol Command Description
Command Name
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Function
Command Packet
Return Packet
Parameter
Reset
Focus Far
Focus Near
Zoom Wide
Zoom Tele
AF Stop
One push AF
ZOOM Direct
USER PRESET Save
Function
Command Packet
Return Packet
COLOR CCD CAMERA
48 User’s Manual
Byte1
Byte2
Byte3
Execution Description.
STX
CAM ID
HOST ADDR
STX
CAM ID
HOST ADDR
Reset all data to factory default value.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move focus lens to far direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move focus lens to near direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move zoom lens to wide direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move wide lens to tele direction.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Stop zoom & focus lens moving.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Unconditionally execute auto focus.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Move to ZOOM position that is set up by users
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
P1, P2 : ZOOM position set (0000h~06EAh)
P3 : D-ZOOM position set(00h~03h)
Save current user preset configuration information.
A0h
CAM ID
HOST ADDR
A0h
CAM ID
HOST ADDR
Byte4 || Byte5
Byte6
Byte7
Byte8
Byte9
Byte10
Byte11
Command
Response
Data3
Data3
Data4
Data4
Data5
Data5
Data6
Data6
ETX
ETX
CHECK SUM
CHECK SUM
000Fh
000Fh
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0100h
0100h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0200h
0200h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0040h
0040h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0020h
0020h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0000h
0000h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0045h
0045h
00h
00h
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
00FFh
00FFh
P1
P1
P2
P2
P3
P3
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
0003h
0003h
P1
P1
00h
00h
00h
00h
00h
00h
AFh
AFh
CHECK SUM
CHECK SUM
COLOR CCD CAMERA
49 User’s Manual
Protocol Command Description
Parameter
P1: 00h = USER PRESET 1
01h = USER PRESET 2
02h = USER PRESET 3
03h = USER PRESET 4
04h = USER PRESET 5
05h = USER PRESET 6
06h = USER PRESET 7
07h = USER PRESET 8
USER PRESET EXEC.
Function
Execute selected user preset.
Command Packet
A0h
CAM ID
HOST ADDR
0007h
P1
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0007h
P1
00h
00h
00h
AFh
CHECK SUM
Parameter
P1: 00h = USER PRESET 1
01h = USER PRESET 2
02h = USER PRESET 3
03h = USER PRESET 4
04h = USER PRESET 5
05h = USER PRESET 6
06h = USER PRESET 7
07h = USER PRESET 8
OSD Menu On/Off
Function
Display OSD menu on the screen.
Clear OSD menu and save current menu setup.
Command Packet
A0h
CAM ID
HOST ADDR
00B1h
P1
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
00B1h
P1
00h
00h
00h
AFh
CHECK SUM
Parameter
P1: 00h = ON
Function
Move OSD arrow to up.
01h = OFF
OSD Menu Up
Command Packet
A0h
CAM ID
HOST ADDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0008h
00h
00h
00h
00h
AFh
CHECK SUM
COLOR CCD CAMERA
50 User’s Manual
COLOR CCD CAMERA
51 User’s Manual
Protocol Command Description
OSD Menu Down
OSD Menu Left
OSD Menu Right
OSD Menu Set
OSD Menu ESC
Function
Move OSD arrow to down.
Command Packet
A0h
CAM ID
HOST ADDR
0010h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0010h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move OSD arrow to left.
Command Packet
A0h
CAM ID
HOST ADDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0004h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move OSD arrow to right.
Command Packet
A0h
CAM ID
HOST ADDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0002h
00h
00h
00h
00h
AFh
CHECK SUM
Functio
Move to inside menu
Command Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0100h
00h
00h
00h
00h
AFh
CHECK SUM
Function
Move to upper menu.
Command Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
Return Packet
A0h
CAM ID
HOST ADDR
0200h
00h
00h
00h
00h
AFh
CHECK SUM
COLOR CCD CAMERA
52 User’s Manual
COLOR CCD CAMERA
53 User’s Manual
DECLARATION OF CONFORMITY
Application of Council Directive(s)
89 / 336 / EEC
Manufacturer's Name
SAMSUNG TECHWIN CO., LTD
Manufacturer's Address
SAMSUNG TECHWIN CO., LTD
42, SUNGJU-DONG CHANGWON-CITY,
KYUNGNAM, KOREA, 641-120
European Representative Name
European Representative Address
Equipment Type/Environment
CCTV Camera
Model Name
SDZ-330
Beginning Serial NO.
S5900001
Year of Manufacture
2005. 9. 1
Conformance to
EN 50081-1 : 1992
EMC-Directive 89/336 EEC and 92/31/EEC
EN 50130-4 : 1996
We, the undersigned, hereby declare that the equipment specified above conforms
to the above Directive(s).
Manufacturer
SAMSUNG TECHWIN CO., LTD
Signature
Legal Representative in Europe
Signature
Full Name
YOUNG TAEK SON
Full Name
Position
QUALITY CONTROL MANAGER
Position
Place
CHANGWON, KOREA
Place
Date
2005. 9. 1
Date
MEMO
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising