Ice Maker

User Manual

PICEM35

NutrichefKitchen.com

Description

1 Upper Cover

2 Front Cover

3 Control Panel

4 Ice Basket

5 Water Reservoir

6 Back Cover

7 Fan Cover

8 Fan

9 Socket

10 Plug

11 Drain pipe

Before/First Use of Your Ice Maker

1.During transportation, the incline angle of the cabinet should not be over 45° .Do not turn the Ice

maker upside down. As this may damage the compressor and sealed system.

2.Remove all packing material and carefully check your ice maker to ensure it is in good condition and

that there is no damage to the ice maker or power cord and plug.

3.The Ice maker should be placed horizontally on a level surface.To ensure proper ventilation for your

Ice maker allow 150mm of space at the top, the back and on each side. Do not install the Ice maker

near an oven, radiator, or any other heat source.

4.Before using the Ice maker for the first time, please wait 2 hours after positioning it, and keep the front

lid open for at least 2hours

5.Ensure that the voltage indicated on the ice maker corresponds with the voltage in your home.

6.Pure water is not allowed to be used on this unit, spring water is recommended.

Control Panel Operation press this button to turn the machine on press this button to turn the machine off press this button to change which time need to be changed press this button to set the time ice full indicator, it turns on when the ice is full

deficient indicator, it turns on if water in water reservoir is not enough

Notice: please make sure the water is not over the max water level

ice making indicator, it is running when the machine is on ice making turn on and turn off indicator, machine turns on/off at setting time

time indicator

Operating Instructions

Step 1.

Plug in the machine into the socket.

Step 2.

Add water to the water tank with cup included in the machine.

Step 3.

Press “ON” to start the machine.

Step 4.

Water is pumped into the water tray from the water reservoir. It takes about 30 seconds

Note: If no water is pumped up to the water tray over two cycles but the water in water tank is

enough, then please open the drain cap, and let several drops water runs out.Then press

Step 5.

to restart the unit

Ice making cycle begins. The evaporator in the water tray starts to form ice onto the evaporator fingers.

Note: For the first three cycles, the ice may be small and irregular in size.

Step 6.

Once ice making cycle completed, the water tray will tilt forward; the remaining water will flow back to the water reservoir and the ice cubes will drop from the fingers. You will hear a sound as the ices cubes are released. Ice are dropped to the ice basket directly

Step 7.

In about 30 seconds, the water tray will tilt backward. Once the water tray returns to its leveled position, the second ice making cycle begins.

Step 8.

Press “OFF” to stop the machine.

Step 9.

If is on, if still want to make ice, then add water to the water tank , same as step 2.If no water is pumped up to the water tray over two cycles but the water in water tank is enough, then please open the drain cap, and let several drops water runs out.

Noted: please take out the ice first, then add one full cup of water, so as to avoid overflow of water when the ice melt.

Step 10.

Also you can set the clock, automatically turn on and turn off time via following steps:

1.

Set clock: press “TIME” and “SET” alternatively to change the time, three seconds later the setting is valid.

2.

Turn On: press button “TIME” till the indicator ON beside the time area lights up, then press

“TIME” and “SET” alternatively to change the time, after the time flash stops, press “SET” again till the indicator ON beside the time area is always lights up.

3.

Turn off: button “TIME” till the indicator OFF beside the time area lights up, then press “TIME” and

“SET” alternatively to change the time, after the time flash stops, press “SET” again till the indicator

OFF beside the time area is always lights up.

Step 11.

When is on, please pull the drawer out, and take out the ice with the ice collecting tray.

Notice: For best performance, water temperature should be between 7°C and 35°C and ambient between 15°C and 38°C.

Caring

1.Clean the inner liner, ice collecting tray, water box, ice shovel and evaporator frequently. When

cleaning, unplug the unit and remove the ice cubes. Use a diluted solution of water and vinegar to

clean the inside and the outside surface of the Ice maker. Do not spray Ice maker with chemicals or

diluted agents such as acids, gasoline or oil. Rinse thoroughly before starting.

2.Keep ventilation openings in the appliance enclosure, or in the built-in structure, clear of obstruction. Do

not use mechanical devices or other means to accelerate the defrosting process, other than those

recommended by the manufacturer.

3.If the icemaker is reused after a long time, the water pump may not pump sufficient water due to an air

block, the deficient water indicator turns on in this case . To correct this press the START button again,

then the icemaker will work normally.

4.To ensure the cleanliness of the ice cubes, water in the water reservoir should be replaced every 24

hours.

5.If the compressor stops for any reason such as water shortage, too much Ice, power off, etc... Do not

start the system right away, wait 3 minutes, and then re-start the Ice maker.

6.Always use fresh water before starting ice production either at initial installation or after a long shut-off

period.

Safety Notice

In order to avoid any accidents, please refer to following operation:

1. Disconnect power before servicing.

2. Do not pull directly on wire when plugging or unplugging the unit.

3. If ice is abnormal, please call the seller.

4. It is normal for the compressor and condenser surface to reach temperatures between 70°C and

90°C during operation and surrounding areas may be hot. Please don't touch it.

5. Due to fast freezing, ice cubes may appear “Cloudy”. This is trapped air in the water and it will not affect quality or taste of ice.

6. When out of use, please open the drawer at least 2cm to allow for air circulation and avoid any metallic components becoming rusted.

7. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

8. This appliance can be used by children aged from 8years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

9.Children shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

10. WARNING: fill with bottled or good quality tap water only. (Do not fill with fruit juices or other drink types).

11. WARNING – Keep the air vents on the sides of the machine unblocked at all times.

12. WARNING – Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

13. WARNING – Do not damage the refrigerant circuit.

14. WARNING – Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

Troubleshooting

1. Please note, if a power failure occurs due to disconnection of the power cord, or the off power button has been pushed off during an ice making cycle, small ice chips may formed and lodge in the automatic shovel causing it to jam. If this occurs, the ice chips may be removed by disconnecting the power cord and gently pushing the shovel to the rear of the cabinet and removing the ice chips, then restarting.

2. Please restart the ice maker by pressing Stop and then Start. If the Ice shovel does not push the Ice into the Ice collector after the formed Ice drops from the evaporator finger while at the same time the M light is on, check to see if the water tray is horizontal or balanced. If not then adjust by pressing the Ice shovel lightly with your finger. Then re-start the Ice maker.

The compressor works abnormally with a Buzzing noise

Water shortage indicator light is on

The voltage is lower than recommended

1.There is no water

2.The pump is full of air

Suggested Solutions

Stop the Ice maker and do not restart until the voltage is normal.

“ON”button is not on Blown fuse/ No power

1.Press the stop button, fill with water, wait 3 minutes and press the start button to restart. When the water has reached the fill line the ice maker will restart automatically.

2.Open the drain cap, and let several drops water runs out.

Replace fuse / Turn power on

The Ice made is too large and with pieces sticking together.

Conditions for Ice making

Cycle are right but no ice is made.

The lights of ice full and deficient come on at the same time.

The water temperature in the water storage box or ambient is too low

Refrigerant leaks./ Sealed system is blocked

Stop the machine and reset the ice making cycle. Restart the machine after turning it off. call for service

Water tray is blocked by ice cube

Clear the ice cube under the ice shovel pull out the plug and insert It again then press the ”START” button, two minutes later the machine will restart automatically