genesis colorⅱ

genesis colorⅱ
GENESIS COLORⅡ
LED-CC 20Ⅱ
User Guide
Innovation, Quality, Performance
15-
Professional Entertainment Technology
EC Declaration of Conformity
We declare that our products (lighting equipments) comply
with the following specification and bears CE mark in
accordance with the provision of the Electromagnetic
Compatibility (EMC) Directive 89/336/EEC.
EN55103-1:1996; EN55103-2:1996;
EN61000-3-2:2006; EN:61000-3-3:1995+A1:2001+A2:2005.
&
Harmonized Standard
EN60598-1:2004; EN60598-2-4:1997.
Safety of household and similar electrical appliances
Part 1: General requirements
1-
14-
6. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
TABLE OF CONTENTS
accumulation of dirt on the unit’s optics.
y Clean with soft cloth using normal glass cleaning fluid.
1. Safety Instruction
y Always dry the parts carefully.
y Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
2. Technical Specification
3. How To Set The Unit
4. How To Control The Unit
5. Troubleshooting
6. Fixture Cleaning
13-
2-
1. Safety Instruction
WARNING
5. Troubleshooting
Please read carefully the instruction, which includes important information
Following are a few common problems that may occur during operation. Here are
about the installation, usage and maintenance.
some suggestions for easy troubleshooting:
y Please keep this User Guide for future consultation. If you sell the unit to another user, be
sure that they also receive this instruction booklet.
A. The unit does not work, no light and the fan does not work
1. Check the connection of power and main fuse.
y Unpack and check carefully there is no transportation damage before using the unit.
2. Measure the mains voltage on the main connector.
y Before operating, ensure that the voltage and frequency of power supply match the power
3. Check the power on LED.
requirements of the unit.
B. Not responding to DMX controller
y It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
y The unit is for indoor use only. Use only in a dry location.
y The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the unit or the previous one.
y Disconnect main power before replacement or servicing.
4. Try to use another DMX controller.
y Make sure there is no flammable materials close to the unit while operating as it is fire
5. Check if the DMX cables run near or run alongside to high voltage cables that may
hazard.
cause damage or interference to DMX interface circuit.
y Use safety cable when fixes this unit.
y Maximum ambient temperature is TA: 40℃. Don’t operate it where the temperature is
C. Some units don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
higher than this.
y Unit surface temperature may reach up to 85℃. Don’t touch the housing bare-hand during
master/ slave mode signal.
its operation. Turn off the power and allow about 15 minutes for the unit to cool down
2. Wrong DMX address in the unit. Set the proper address.
before replacing or serving.
D. No response to the sound
y In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or
1. Make sure the unit does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone
malfunction. Please contact the nearest authorized technical assistance center. Always
E. One of the channels is not working well
use the same type spare parts.
y Do not touch any wire during operation as high voltage might be causing electric shock.
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition
Warning
y To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or
moisture.
y Do not open the unit within five minutes after switching off.
3-
12-
y The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
damaged.
Caution
There are no user serviceable parts inside the unit. Do not open the housing or attempt
any repairs yourself. In the unlikely event your unit may require service, please contact
your nearest dealer.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the
unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
1.
2.
If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
structure to which you are attaching the unit is secure and is able to support a weight of 20
adapter-cable.
kg for each unit.
At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it
2. Technical Specification
in the DMX-output of the last unit.
3.
4.
Connect the unit together in a `daisy chain` by XLR plug from the output of the unit to
• The unit is DMX 512 fixture. It features full DMX 512 control. It can be also linked together
the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is
in master/slave connection, as many as required and run by built-in program chase
a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded
sequences automatically or by sound activation through an internal microphone to create
connectors can easily distort the signal and shut down the system.
an intelligent effect.
The DMX output and input connectors are pass-through to maintain the DMX circuit,
when power is disconnected to the unit.
• It can be operated by DMX 512 control or can be used as an individual unit without a
controller.
Each lighting unit needs to have an address set to receive the data sent by the
• Features different preprogrammed chase patterns.
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
• Please use a cable when connecting units together.
6.
The end of the DMX 512 system should be terminated to reduce signal errors.
• Accurate focusable optics system and ultra smooth stepping motors.
7.
3 pin XLR connectors are more popular than 5 pin XLR.
• Fan cooled.
5.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
• Voltage:AC 230V/240V/250V- 50HZ~120V-60HZ
• Fuse: T 2A
Pin 4/5: Not used.
• Power consumption: 31W
• Light source: 10W CREE LED
• Dimension: 206 x 199 x 187 mm
• Weight: 2.4 kg
11-
4-
3. How To Set The Unit
4.4 DMX 512 Configuration
3.1 Control Panel
1 Display:To show the various menus and the selected functions
○
LED
2 DMX
○
3 MASTER
○
4 SLAVE
○
5 SOUND
○
On
DMX input present
On
Master Mode
On
Slave Mode
Flashing
Sound activation
Button
6 MENU
○
7 DOWN
○
8 UP
○
9 ENTER
○
To select the programming functions
4.5 DMX512 Connection
To go backward in the selected functions
To go forward in the selected functions
The DMX 512 is widely used in intelligent lighting control, with a maximum of 512 channels.
To confirm the selected functions
10 Sensitivity: To adjust the sound receiving sensitivity
○
11 Only for remote control: By connect to the 1/4’’ microphone jack to control the unit for
○
Stand by, Function and Mode function.
12 DMXoutput: For DMX512 link, use 3-pin XLR plug cable to link to the next unit.
○
13 DMX input: For DMX512 link, use 3-pin XLR plug cable to input DMX signal.
○
14 Mains input:IEC socket and integrated fuse holder, connect to main power cable.
○
5-
10-
4.1 Master/Slave Built In Preprogrammed Function
3.2 Main Function
By linking the units in master/slave connection, the first unit will control the other units to
To select any of the given functions, press the MENU button up to when the required one is
give an automatic, sound activated, synchronized light show. This function is good when you
showing on the display. Select the function by ENTER button and the display will blink. Use
want an instant show.
DOWN and UP button to change the mode. Once the required mode has been selected,
press the ENTER button to setup or it will automatically return to the main functions without
2-light show
In
(slave mode),
any change after idling 8 seconds. To go back to the functions without any change press the
means the unit works normally and
means
MENU button. The main functions are showing below:
2-light show. In order to create a great light show, you can set
on the second unit to
get contrast movement to each other, even if you have two units only.
4.2 Easy Controller
The easy remote control is used only in master/slave mode. By connecting to the 1/4”
microphone jack of the first unit, you will find that the remote control on the first unit will
control all the other units functions press the MENU button again.
Stand By
Blackout the unit
Function
1. Sync. Strobe
Select Color
2. Async strobe
3. Sound Strobe
Mode
Sound (LED OFF)
Show (LED On)
4.3 DMX Controller
An universal DMX controller to control the units, you have to set DMX address from 1 to 512
channel so that the units can receive DMX signal.
DMX 512 Address Setting
is showing on the display. Pressing ENTER
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to change the
Press the MENU button up to when the
DMX512 address. Once the address has been selected, press and keep ENTER
Once the address has been selected, press the ENTER button to setup or automatically
button pressed up to when the display stops blinking or storing automatically 8
return to the main functions without any change after 8 seconds. To go back to the functions
seconds later. To go back to the functions without any change press the MENU
without any change press the MENU button again.
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
button again. If you use please refer to the following diagram to address your
Slave Mode
DMX512 channel for the first 4 units.
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
(2 light show)
(3 light show)
(4 light show) mode.
Once the mode has been selected, press the ENTER button to setup or automatically return
9-
6-
to the main functions without any change after 8 seconds. To go back to the functions
ENTER button and the display will run self-test by built-in program. To go back to the
without any change press the MENU button again.
functions press the MENU button again.
Sound Mode
Temperature Test
Press the MENU button until the
is showing on the display. Pressing ENTER button
and the display will blink. Use DOWN and UP button to select the
(sound on) or
(sound off) mode. Once the mode has been selected, press the ENTER button to
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
button and the display will show the temperature of the unit. To go back to the functions
press the MENU button again.
setup or automatically return to the main functions without any change after 8 seconds. To
Fixture Hours
go back to the functions without any change press the MENU button again.
Press the MENU button up to when the
is blinking on the display. Pressing
ENTER button and the display will show the number of working hours of the unit.
Blackout Mode
Press the MENU button up to when the
is showing on the display. Pressing
To go back to the functions press the MENU button again.
ENTER button and the display will blink. Use DOWN and UP button to select the
(yes blackout) or
Software version
(no blackout) mode. Once the mode has been selected, press the
ENTER button to setup or automatically return to the main functions without any change
Press the MENU button up to when the
after 8 seconds. To go back to the functions without any change press the MENU button
button and the display will show the version of software of the unit. To go back to the
again.
functions press the MENU button again.
Reset
Led Display
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(Led on) or
is blinking on the display. Pressing ENTER
(Led off) mode. Once the mode has been selected, press the ENTER
is blinking on the display. Pressing ENTER
Press the MENU button up to when the
button and all channels of the unit will return to their standard position. To go back to the
functions without any change press the MENU button again.
button to setup or automatically return to the main functions without any change after 8
seconds. To go back to the functions without any change press the MENU button again.
4. How To Control The Unit
Inversion
You can operate the unit in three ways:
Press the MENU button up to when the
is showing on the display. Pressing
ENTER button and the display will blink. Use DOWN and UP button to select the
(normal) or
(inversion) mode. Once the mode has been selected, press the ENTER
1. By master/slave built-in preprogram function
2. By easy controller
3. By universal DMX controller
button to setup or automatically return to the main functions without any change after 8
No need to turn the unit off when you change the DMX address, as new DMX address
seconds. To go back to the functions without any change press the MENU button again.
setting will be effected at once. Every time you turn the unit on, it will show
on the
display and move all the motors to their ‘home’ position and you may hear some noises for
Auto Test
about 20 seconds. After that the unit will be ready to receive DMX signal or run the built in
Press the MENU button up to when the
is blinking on the display. Pressing
7-
programs.
8-
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement