AIRAID 310-208 Cold Air Dam Intake Installation Instructions

10.

Full color instructions can be viewed on our web site at Airaid.com. If you need any assistance please call 1-800-858-3333 to speak with a representative in our Customer Service Center before returning the product.

INTAKE SYSTEMS FOR VEHICLES LISTED ARE 50 STATE

LEGAL. SEE AIRAID.COM FOR CARB STATUS ON EACH

PART FOR A SPECFIC VEHICLE.

13.

Installation Instructions

For Part Numbers:

310-208

311-208

312-208

313-208

700-471 Airaid Oiled Media Filter

701-471 SynthaMax Dry Media Filter - Red

702-471 SynthaMax Dry Media Filter - Black

703-471 SynthaMax Dry Media Filter - Blue

2007-11 Jeep Wrangler (JK)

3.8L V6

Component Identification

1. Airaid Premium Filter

2. Airaid Intake Tube

3. MAF Panel

4. Bottom Panel

5. Reducing Hump Hose

6. Weather Strip 20”

7. 1/4-20x1/2” Button Head Bolt

1

1

1

1

1

1

3

6-32x 5/16” Screw 7

3/8-16x1 1/4”Button Head Bolt 2

Hose 1

1. Disconnect the negative battery cable.

Very Carefully r emove the temper atur e sensor from the factory intake tube by using a circular motion while pulling it straight out. There is no need to disconnect the wiring harness.

2. Loosen the intake tube hose clamp on the throttle body.

3. Unlatch the 4 metal clips that hold the factory air cleaner lid to the base. Next disconnect the breather hose that attaches to the rear of the air cleaner lid.

4. Remove the factory intake tube, and lid from the vehicle as an assembly.

5. While rocking the factory air cleaner base back and forth, pull up, and remove it from the vehicle. There are no bolts holding it down, just grommets.

6. Remove the 2 lower grommets from the factory plastic air cleaner mount.

7. With a 10mm socket, remove and save the bolt from the factory plastic air cleaner mount. It will be re-installed in step #12.

8. With a 10mm socket, remove and save the bolt that holds the radiator to the radiator support. It will be reused in step #10.

9. Install the 2 well nuts (#18) into the holes in the plastic air cleaner mount where you removed the grommets in step #6.

10. Insert the bolt, removed in step #8, thru the round hole in the provided L-bracket, and back into the radiator support. Leave the bolt slightly loose for now.

11. Assemble the Cool Air Dam panels (#3 & 4) as shown, using the seven 6-32 screws (#10), flat washers (#11), and keps nuts (#12). Apply the

Airaid Decal as shown.

12. Install the CAD into the vehicle. Install the two 3/8 x1 1/4” button head bolts (#13), thru the bottom panel, and into the well nuts.

Reinstall the factory bolt removed in step #7 thru the panel, and into the fender well.

Tighten all three bolts at this time.

13. Using one 1/4” button head bolt (#7), 1/4” flat washer (#8), and 1/4” serrated nut (#9), attach the CAD panel to the L-bracket, as shown. Now tighten the radiator mounting bolt on the other end of the L-bracket.

14. Install the supplied grommet (#17) into the

Airaid Intake Tube (#2).

#44

#52

15. Install the reducing hump hose (#5) onto the throttle body as shown, with the #44 hose clamp (#15) on the back, and the #52 hose clamp (#16) on the front. Leave the clamps loose for now.

16. Install the Airaid Intake Tube into the hump hose first, and then rotate it down, and into the CAD. Install two 1/4” button head bolts (#7), and 1/4” flat washers (#8) thru the

CAD, and into the inser ts in the tube. Adjust for fit, and tighten both hose clamps, and bolts.

17. Very Carefully r einstall the temper atur e sensor removed in step #1, into the grommet in the

Airaid Intake Tube. Reconnect the factory breather hose to the nipple on the intake tube.

19. Double check your work!

Make sure there is no foreign material in the intake path. Make sure all clamps, hoses, bolts, and screws are tight. Periodically check all clamps, and fasteners for tightness.

18. Install the Airaid Premium Filter (#1) onto the intake tube, and tighten the clamp. Next install the weatherstrip (#6) onto the top of the

CAD as shown.

20. Reconnect the negative battery cable!

Thank you for purchasing the Airaid Intake System. Contact Airaid @ (800) 498-6951 8:00 AM - 5:00 PM MST weekdays for questions regarding fit or instructions that are not clear to you. Your Airaid Intake System was carefully inspected and packaged. Check that no parts are missing, or were damaged during shipping. If any parts are missing, contact Airaid. The air filter element is protected from direct exposure to water and debris; care should be taken not to drive through deep water. WATER INGESTION IS THE DRIVERS RESPONSIBILTY! The air filter is reusable and should be cleaned periodically.

FILTER IDENTIFICATION

700-471 Airaid Oiled Media 701-471 Airaid SynthaMax Dry Media - Red

702-471 Airaid SynthaMax Dry Media - Black 703-471 Airaid SynthaMax Dry Media - Blue

For your Oiled media filter we suggest using the AIRAID Filter

Tune-Up Kit!

Synthamax Air Filters do not require oil. Service air filter as needed by cleaning with common nonpetroleum all-purpose household cleaner and water. Simple Green®,

Formula 409® or equivalent works great. Apply cleaner to outside of air filter and allow to soak. Then flush filter clean from the inside out with a garden hose and repeat steps if necessary. Do not apply high pressure water or air to clean filter.

Allow filter to air dry and reinstall.

P/N 790-551 Aerosol Spray

P/N 790-550 Squeeze Spray

INTAKE SYSTEMS FOR VEHICLES LISTED ARE 50 STATE

LEGAL. SEE AIRAID.COM FOR CARB STATUS ON EACH

PART FOR A SPECFIC VEHICLE.

Airaid. 1815 West Crest Lane. Phoenix AZ 85027 (800) 498-6951 [email protected]

www.airaid.com

AIR-I31208B

REV.07.05.16