Use, Care, and Installation Guide

Use, Care, and Installation Guide
Use, Care, and Installation Guide
www.windcrestcnp.com
UIX2916S
UIX3816S
Model number:
Serial Number:
Date of Purchase:
Sales Dealer:
SEP12.0302 © 2012 Wind Crest CNP Industries, Inc.
READ AND SAVE THESE INSTRUCTIONS
www.windcrestcnp.com
INSTALLATION
Ducting Calculation Sheet .......................................
Mounting Height & Clearance................................
Ducting Options ...........................................................
Specifications ...............................................................
Electrical .........................................................................
Installing the Insert .....................................................
VEN111I Dual Internal Blower Kit.........................
5
6
7
8
9
10
11-12
FEATURES & CONTROLS
Slide Controls ............................................................... 13
MAINTENANCE
Cleaning and Installing Filters ............................... 14
Lights ................................................................................ 15
TROUBLESHOOTING................................................................ 16
LIST OF PARTS AND ACCESSORIES .............................. 17
1
Table of Contents
SAFETY NOTICE ................................................................. 2-3
LIST OF MATERIALS ....................................................... 4
Important Safety Notice
www.windcrestcnp.com
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.
WARNING
TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning
agents or detergents. Suitable for use in household cooking area.
WARNING
TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
b. Always turn hood ON when cooking at high heat or when flaming food
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
e. Keep fan, filters and grease laden surfaces clean.
f. Use high setting on hood only when necessary.
g. Don’t leave hood unattended when cooking.
h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN – You may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards.
Including fire-rated construction.
b. Sufficient air is needed for power combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent
back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National
Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and
the local code authorities.
c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d. Ducted fans must always vent to the outdoors.
e. Make sure the power is off before installing, wiring or maintenancing.
© Wind Crest CNP Industries, Inc.
2
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
CAUTION
To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,
attics, crawl spaces or garages.
OPERATION
Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers
and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,
maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to
negligence and the warranty of the unit automatically expires due to improper maintenance.
*NOTE: Please check www.windcrestcnp.com for revisions before doing any custom work.
ELECTRICAL REQUIREMENTS
Important:
Observe all governing codes and ordinances.
It is the customer’s responsibility:
- To contact a qualified electrical installer.
- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70
latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and
all local codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the range hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575
This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit
protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to
Electrical Diagram on product.
UIX2916S (single blower) - 390W, 3.25 Amps
UIX2916S (dual blower) - 710W, 5.95 Amps
UIX3816S (dual blower) - 780W, 6.55 Amps
A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase
and install appropriate connector if necessary.
3
Important Safety Notice
WARNING
List of Materials
www.windcrestcnp.com
MODELS: UIX2916S AND UIX3816S
PARTS SUPPLIED
UIX2916S
1 - Insert
2 - Decorative mesh filters
2 - Halogen light bulbs (pre-installed)
1 - 600CFM Single internal blower (pre-installed)
1 - 8” round adapter
1 - Hardware package
UIX3816S
1 - Insert
3 - Baffle filters
4 - Halogen light bulbs (pre-installed)
1 - 1200CFM Dual internal blower (pre-installed)
1 - 10” round adapter
1 - Hardware package
HARDWARE PACKAGE CONTENTS
Suction Cup (1)
M4 x 1” (6)
M4 x 8 (4)
Wire Caps (3)
PARTS NOT SUPPLIED
- Ducting, conduit and all installation tools
- Cable connector (if required by local codes)
- *Dual internal blower kit (VEN111I) - UIX2916S only
- Optional stainless steel hood liner
*Dual blower kit includes blower plate and 1 blower. Blower from UIX2916S is required to complete installation.
© Wind Crest CNP Industries, Inc.
4
Equivalent number
length x used
=
Duct pieces
Total
Total
3-1/ 4” x 10” 1 Ft.
Rect.,
straight
x(
) =
Ft.
6” Round
30 Ft.
wall cap
with damper
x(
) =
Ft.
6” Round,
straight
1 Ft.
x(
) =
Ft.
6” Round,
roof cap
x(
) =
Ft.
7”-10” Round, 1 Ft.
x(
) =
Ft.
6” round to
1 Ft.
3-1/ 4” x 10”
rect.
transition
x(
) =
Ft.
3-1/ 4” x 10” 15 Ft.
Rect.90 0
elbow
x(
) =
Ft.
x(
) =
Ft.
3-1/ 4” x 10” 9 Ft.
Rect.45 0
elbow
x(
) =
Ft.
6” round to
16 Ft.
3-1/ 4” x 10”
rect.
transition
90 0 elbow
7” - 10”
Round,
90 0 elbow
15 Ft.
x(
) =
Ft.
3-1/ 4” x 10” 24 Ft.
Rect.90 0
flat elbow
x(
7” - 10”
Round,
45 0 elbow
9 Ft.
x(
) =
Ft.
3-1/ 4” x 10” 30 Ft.
Rect.
wall cap
with damper
x(
7” - 10”
30 Ft.
Round
wall cap
with damper
x(
) =
Ft.
3-1/ 4” x 10” 5 Ft.
Rect.to
6” round
transition
x(
) =
Ft.
7” - 10”
Round,
roof cap
x(
) =
Ft.
3-1/ 4” x 10” 20 Ft.
Rect.to
6” round
transition
90 0 elbow
x(
) =
Ft.
7” round to
8 Ft.
3 1/ 4” x 10”
rect.
transition
x(
) =
Ft.
) =
Ft.
15 Ft.
x(
) =
Ft.
7” round to
23 Ft.
3-1/ 4” x 10”
rect.
transition
90 0 elbow
x(
6” Round,
90 0 elbow
6” Round,
45 0 elbow
9 Ft.
x(
) =
Ft.
Subtotal column 2 =
Ft.
Subtotal column 1 =
Ft.
Total ductwork
Ft.
straight
) =
) =
Subtotal column 1 =
30 Ft.
Ft.
Ft.
Ft.
Maximum Duct Length: For satisfactory air movement, the
total duct length should not exceed 50 equivalent feet.
5
30 Ft.
=
Installation – Ducting Calculation Sheet
Equivalent number
length x used
=
Duct pieces
Installation – Mounting Height & Clearance
www.windcrestcnp.com
Minimum mount height between range top to hood
bottom should be no less than 30”.
Maximum mount height should be no higher than
36”.
It is important to install the hood at the proper
mounting height. Hoods mounted too low could
result in heat damage and fire hazard; while hoods
mounted too high will be hard to reach and will
lose its performance and efficiency.
If available, also refer range manufacturer’s height
clearance requirements and recommended hood
mounting height above range.
Min 30" - Max 36"
UIX2916S
Vertical Ducting:
6” round minimum (single blower - included)
8” round minimum (dual blower)
Horizontal Ducting:
N/A
36"
DUCTING
A minimum of 6” round or 3-1/4” x 10” rectangular
duct must be used to maintain maximum air flow
efficiency for single blower and 8”-10” round duct
for dual internal blower.
UIX3816S
Vertical Ducting:
10” round minimum (dual blower - included)
Horizontal Ducting:
N/A
Always use rigid type metal ducts only. Flexible
ducts could restrict air flow by up to 50%.
Also use calculation (on page 5) to compute total
available duct run when using elbows, transitions
and caps.
ALWAYS, when possible, reduce the number or
transitions and turns. If long duct run is required,
increase duct size.
If turns or transitions are required; install as far
away from hood duct output and as far apart,
between the two as possible.
© Wind Crest CNP Industries, Inc.
6
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.
All exhaust must be ducted to the outside.
Use metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints with certified Silver Tape or Duct Tape.
Some Ducting Options
side wall cap
w/ gravity damper
side wall cap
w/ gravity damper
Soffit or crawl space
Roof Pitch w/
Flashing & Cap
7
Installation – Ducting Options
WARNING FIRE HAZARD
*7 7/8” or
5 7/8”
5” or 1”
24 5/8”
14 3/4”
1 1/2”
29 13/16”
1 5/16”
elec.
k/o
25 15/16”
6 1/2”
CL
14 11/16”
15 13/16”
11 7/16”
2 3/8”
4 3/4”
11 7/16”
CL
4 3/8”
*8” round adapter only needed if using dual internal blower kit.
6” round collar is standard and requires no adapter.
UIX2916S
front
UIX2916S
top
13/16”
11 7/16”
14 11/16”
15 13/16”
UIX2916S/UIX3816S
side
33 1/8”
14 3/4”
*9 7/8”
14 11/16”
15 13/16”
A
4 1/2”
CL
6 1/2”
4 3/4”
2 3/8”
11 7/16”
7”
CL
11 7/16”
Installation – Specifications
www.windcrestcnp.com
2 5/8”
A: elec.
k/o
34 5/8”
38 7/16”
UIX3816S
front
UIX3816S
top
© Wind Crest CNP Industries, Inc.
8
WARNING
All Electrical work must be performed by qualified electrician or person with similar technical know
how and background.
For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use
extension cord or adapter plug with this appliance.
Follow national electrical codes or prevailing local codes and ordinances.
Electrical Supply:
This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded
branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire w/
ground. Please also refer Electrical Diagram labeled on product.
Cable Lock:
A cable locking connector (not supplied) might also be required by local codes. Check with local requirements
and codes, purchase and install appropriate connector if necessary.
Cable Lock
9
Installation – Electrical
ELECTRICAL
! CAUTION: At least two installers are
required due to the weight and size of the
hood.
UIX2916S
26 1/16”
-
UIX3816S
34 11/16”
C/L
1. If converting UIX2916S from single internal blower to dual internal
blower make sure the conversion is done before installing insert.
Refer to page 11 for instructions
14 3/4”
Installation – Installing the Insert
www.windcrestcnp.com
C/L
2. Install 8” round adapter to top of UIX2916S or 10” adapter on top of
UIX3816S. See page 12, step 8 for instuctions.
3. Install optional UL29xxS or UL38xxS Stainless Steel Liner. Review
manual included with liner for more details.
cabinet bottom cut-out size
FIG 1
4. If no liner is used cut out an opening in the bottom of the cabinet by
following the dimensions in FIG 1.
5. Lift insert into opening and secure to bottom of cabinet using (4) M4
stainless steel screws, (1) in each corner; see FIG 2.
note: Wood blocking may need to be added to cabinet base if
additional support is needed.
Ductwork
elec.
minimum
3/4” wood base
Front View
6. Install duct work and seal with duct tape.
7. Install electrical.
8. Remove all packing material before using insert.
Switch power on and check for leaks around duct tape.
metal or other non
combustible material
(4) M4 ss wood screws
(1) in each corner
9. Install decorative mesh filters for UIX2916S or baffle filters for
UIX3816S. See page 14 for more details.
WARNING:
Remove support screw from top of insert
FIG 2
remove support screw
before proceeding to step 5. FIG 2b
FIG 2b
© Wind Crest CNP Industries, Inc.
10
NOTE: SINGLE BLOWER FROM UIX2916S IS REQUIRED TO COMPLETE VEN111I DUAL BLOWER KIT.
UIX3816S ALREADY INCLUDES A DUAL BLOWER.
1. Disconnect single blower wire from inside of
the insert.
2. Remove support screw from top of insert near
the back. Remove 2 screws holding blower plate
to insert and pull blower towards front of hood to
release from internal bracket.
3. Unscrew (4) screws holding blower to blower
plate and remove blower. Remove metal damper
from blower. Discard single blower plate.
4. Picture of VEN111I dual blower kit.
5. Use the blower removed from the single blower
plate and install it into the dual blower plate.
6. Connect 9 pin male molex connector from blower
to 9 pin female molex connector on dual blower
capacitor box.
11
Installation – VEN111I Dual Blower Kit
OPTIONAL VEN111I DUAL BLOWER KIT IS FOR USE WITH UIX2916S.
Installation – VEN111I Dual Blower Kit
www.windcrestcnp.com
7. Re-attach dual blower plate to insert by following
removal instructions in reverse. Re-attach
blower wire to insert.
8. Place 8” round adapter (included with
UIX2916S) on top of insert and secure with (4)
M4x8 screws. Connect 8” round duct work.
For UIX3816S install 10” round adapter
(included with insert) on top of insert and secure
with (4) M4x8 screws. Connect 10” round duct
work.
note: The 8”and 10” round adapters are fitted
with a metal damper to prevent outside airflow
from entering the kitchen.
The 6” round single blower is also fitted with a
metal damper. If using the VEN111I dual blower
kit, the metal damper from the 6” round single
blower must be removed prior to instaling the
8”round adapter. See installation step 3 on page
11.
© Wind Crest CNP Industries, Inc.
12
III
II
I
2 Lights Bright/Dim/Off
II
0
1 BLOWER ON/OFF/SPEED SELECTION
0 is off, I is low speed, II is medium speed and III is high speed.
2 LIGHTS BRIGHT/DIM/OFF
0 is off, I is dim, and II is bright.
13
I
0
Features & Controls – Slide Controls
1 Blower On/Off Speed Selection
Maintenance – Cleaning and Installing Filters
www.windcrestcnp.com
SURFACE MAINTENANCE:
Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent,
or steel wool/ scoring pads which will scratch and damage surface. Do not use products containing chlorine
bleach or orange cleaners.
For heavier soil use liquid degreaser.
After cleaning, you may use non-abrasive stainless steel polish/ cleaners, to polish and buff out the stainless
luster and grain. Always scrub lightly using a micro fiber or clean cotton cloth and with the grain.
Decorative Mesh and Baffle Filters
The filters are intended to trap residue and grease from cooking. Although the filters should never need
replacing, they are required to be cleaned every 30 days or more often depending on cooking habits.
Filters may be placed in dishwasher at low heat or soaked in hot soapy water Dry filters and re-install before
using hood.
Removing Decorative Mesh Filters (UIX2916S), FIG 4:
1. Pull down on filter handle.
2. Remove filter by pulling it out from the power pack.
Removing Baffle Filters (UIX3816S), FIG 5:
1. Pull filter towards front of power pack using handles.
1
2. Pivot back of filter downward.
2
3. Remove filter by pushing it away from the power pack.
FIG 4
1
2
3
FIG 5
© Wind Crest CNP Industries, Inc.
14
CAUTION: Light bulb becomes extremely hot when turned on.
DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.
Make sure all power is turned off and bulbs are not hot.
Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and
falls out.
If bulbs are difficult to turn due to prolonged use, firmly attach a glass suction cup approximately the
diameter of the bulb or use a rubber/latex glove and turn counter clockwise.
Replacement bulbs are available at specialty lighting stores. Purchase type MR16 (GU-10) 35W halogen.
For WindCrest part numbers please turn to page 17 of the manual.
Bottom View
15
Maintenance – Lights
REPLACING LIGHT BULBS
Troubleshooting
www.windcrestcnp.com
TROUBLESHOOTING PROCEDURES FOR UIX2916S AND UIX3816S
Issue
Cause
What to do
After installation,
the unit doesn’t
work.
1. The power source is not turned ON.
1. Make sure the circuit breaker and the unit’s
power is ON.
2. The power line and the cable locking connector
is not connecting properly.
2. Check the power connection with the unit is
connected properly.
3. The switch board and control board wirings are
disconnected.
3. Make sure the wirings between the switch
board and control board are connected
properly.
4. On the switch board, Black/White wire or White
wire is disconnected.
4. Make sure the Black/White wire or White wire
connects properly.
5. The switch board or control board is defective.
5. Change the switch board or control board.
1. The motor is defective, possible seized.
1. Change the motor.
2. The thermally protected system detects if the
motor is too hot to operate and shuts the motor
down.
2. The motor will function properly after the
thermally protected system cool down.
3. Damaged condenser.
3. Change the condenser.
Light works,
but motor is not
turning.
The unit is
vibrating.
1. The motor is not secure in place.
1. Tighten the motor in place.
2. Damaged blower wheel.
2. Change the blower wheel.
3. The hood is not secured in place.
3. Check the installation of the hood.
The motor is
working, but the
lights are not.
1. Defective halogen bulb.
1. Change the halogen bulb.
2. The light bulb is loose.
2. Tighten the light bulb.
The hood is
not venting out
properly.
1. The hood might be hanging to high from the
cook top.
1. Adjust the distance between the cook top and
the bottom of the hood within 30” and 36”
range.
2. The wind from the opened windows or opened
doors in the surrounding area are affecting the
ventilation of the hood.
2. Close all the windows and doors to eliminate
the outside wind flow.
3. Blocking in the duct opening or duct work.
3. Remove all the blocking from the duct work or
duct opening.
4. The direction of duct opening is against the wind.
4. Adjust the duct opening direction.
Metal filter is
vibrating.
5. Using the wrong size of ducting.
5. Change the ducting to the size specified.
1. Metal filter is loose.
1. Change the metal filter.
2. Spring clip is broken.
2. Change the spring clip.
© Wind Crest CNP Industries, Inc.
16
PART #
Replacement Parts
Light Bulb MR16 (GU10) 35W (each)
Decorative Mesh Filter (each)
Baffle Filter (each)
11206.00
11271.00
11272.00
Optional Accessories
Dual blower kit(UIX2916S only)
Liner,36” (UIX2916S)
Liner,42” (UIX2916S)
Liner,48” (UIX3816S)
Liner,54” (UIX3816S)
Liner,60” (UIX3816S)
VEN111I
UL2936S
UL2942S
UL3848S
UL3854S
UL3860S
To order parts, call us at 1.877.387.6721
17
List of Parts and Accessories
DESCRIPTION
www.wincrestcnp.com
TO OBTAIN SERVICE UNDER WARRANTY:
or any Service Related Questions, please call:
1-877-387-6721
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
TO OBTAIN SERVICE UNDER WARRANTY: You must present proof of original purchase date.
Please keep a copy of your dated proof of purchase (sales slip) in order to obtain service under warranty.
FULL ONE YEAR WARRANTY
Covers repair and replacement of parts found to be defective due to material and workmanship for one year from date of
purchase.
SERVICE MUST BE PROVIDED BY A FACTORY AUTHORIZED SERVICE AGENCY, DURING NORMAL WORKING
HOURS.
ITEMS NOT COVERED IN WARRANTY
1.) Damage or repairs due to service by unauthorized agency or use of unauthorized parts.
2.) Service visits to teach you how to use the appliance.
3.) Correct installation related problems - you are responsible for providing electrical wiring and other connection items.
4.) Reset circuit breakers or replace fuses.
5.) Damage caused by abuse, accident, alteration, misuse and local code violations.
6.) Failure due to other than normal house use.
7.) Service to replace consumable parts (i.e. Light Bulbs, Heat Lamps, Filters).
8.) Expenses for travel and transportation if appliance is located in a remote area.
You may also write to us at:
Wind Crest™ by CNP Industries, Inc.
351 Thor Place
Brea, CA 92821
(877) 387-6721
This warranty applies to appliances used in residential applications only. The warranty is for products purchased and retained in the 50
states of the USA, the District of Columbia, and Canada. This warranty gives you specific legal rights. You may also have other rights,
which vary from state to state.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement