Sony CFD-922L User's manual

Sony CFD-922L User's manual
Playing a tape
English
Use TYPE I (normal) tape only.
Use TYPE I (normal) tape only.
Recording
Falling asleep to music
Precautions
On safety
1
1
Press TAPE (direct power-on).
Press xZ to open the tape compartment and insert a
blank tape.
With the side you want to
record on facing upward
Display
1
2
Play the music source you want.
Press SLEEP to display “SLEEP.”
c
• As the laser beam used in the CD
player section is harmful to the
eyes, do not attempt to
disassemble the casing. Refer
servicing to qualified personnel
only.
• Should any solid object or liquid
fall into the player, unplug the
player, and have it checked by
qualified personnel before
operating it any further.
Cleaning the cabinet
2
Press xZ to open the tape compartment and insert a
recorded tape. Close the compartment.
With the side you want to
play facing upward
2
Select the program source you want to record.
To record from the CD player
Press CD and insert a CD (See "Playing a CD").
c
3
Press SLEEP to select the minutes until the player goes
off automatically.
Each time you press the button, the indication changes
as follows: “60” n “90” n “120” n no indication n
“10” n “20” n “30.”
Display
Display
Press N.
To record from the radio
Press RADIO BAND•AUTO PRESET and tune in the
station you want (See "Listening to the radio").
Display
To
Press
adjust the volume
VOLUME +, – (VOL +, – on the
remote, CFD-S32/S32L only)
stop playback
xZ
fast-forward or rewind the tape
M or m
pause playback
X
Press the button again to resume play
after pause.
3
eject the cassette
xZ
turn on/off the player
OPERATE (or POWER)
Press z to start recording.
(N is depressed automatically.)
Notes on cassettes
• Break off the cassette tab from side A or B to prevent accidental
recording. If you want to reuse the tape for recording, cover the broken
tab with adhesive tape.
Side A
To
Press
stop recording
xZ
pause recording
X
Press the button again to resume recording.
turn on/off the player
Tab for side B
3
OPERATE (or POWER)
Tab for side A
• The use of a cassette with more than 90 minutes of play time is not
recommended except for long, continuous recording or playback.
Tips
• Adjusting the volume or the audio emphasis will not affect the
recording level.
• CFD-S22L/S32L/922L only: If the MW/LW program makes a
whistling sound after you've pressed z in step 3, press PLAY MODE•
MONO/ST ISS (Interference Suppress Switch) repeatedly until the
noise is at a minimum.
• For the best results, use the AC power as a power source for recording.
• To erase a recording, proceed as follows:
1 Insert a tape with the recording you want to erase.
2 Press TAPE.
3 Press z.
To cancel the sleep function
Press OPERATE (or POWER) to turn off the power.
Note
When you are playing a tape using this function:
If the tape length of one side is longer than the set time, the player will
not go off until the tape reaches the end.
• Clean the cabinet, panel and
controls with a soft cloth slightly
moistened with a mild detergent
solution. Do not use any type of
abrasive pad, scouring powder, or
solvent, such as alcohol or
benzine.
On power sources
• For AC operation, check that the
player's operating voltage is
identical with your local power
supply (see "Specifications") and
use the supplied mains lead; do
not use any other type.
The voltage selector is located at
the bottom of the player (for
Brazilian model only).
• The player is not disconnected
from the AC power source
(mains) as long as it is connected
to the wall outlet, even if the
player itself has been turned off.
• For battery operation, use six R20
(size D) batteries.
• When the batteries are not to be
used, remove them to avoid
damage that can be caused by
battery leakage or corrosion.
• The nameplate indicating
operating voltage, power
consumption, etc. is located at the
bottom.
On placement
• Do not leave the player in a
location near heat sources, or in a
place subject to direct sunlight,
excessive dust or mechanical
shock.
• Do not place the player on an
inclined or unstable place.
• Do not place anything within 10
mm of the side of the cabinet. The
ventilation holes must be
unobstructed for the player to
operate properly and prolong the
life of its components.
• If the player is left in a car parked
in the sun, be sure to choose a
location in the car where the
player will not be subjected to the
direct rays of the sun.
• Since a strong magnet is used for
the speakers, keep personal credit
cards using magnetic coding or
spring-wound watches away from
the player to prevent possible
damage from the magnet.
On operation
• If the player is brought directly
from a cold to a warm location, or
is placed in a very damp room,
moisture may condense on the
lenses inside the CD player
section. Should this occur, the
player will not operate properly.
In this case, remove the CD and
wait about an hour for the
moisture to evaporate.
• If the player has not been used for
a long time, set it in the playback
mode to warm it up for a few
minutes before inserting a
cassette.
If you have any questions or
problems concerning your player,
please consult your nearest Sony
dealer.
Troubleshooting
General
The power does not come on.
• Connect the mains lead securely.
• Make sure the batteries are
inserted correctly.
• Replace all the batteries with new
ones if they are weak.
• You cannot turn on the player
with the remote when you operate
the player on batteries (CFD-S32/
S32L only).
The power is not on, and
"bAttErY" and "Error" are
displayed alternately.
• Make sure the batteries are
inserted correctly.
• Replace all the batteries with new
ones if they are weak.
There is no audio.
• Make sure the function you want
to use appears in the display.
• Adjust the volume.
• Unplug the headphones when
listening through speakers.
Noise is heard.
• Someone is using a portable
telephone or other equipment that
emits radio waves near the player.
tMove the portable telephone,
etc., away from the player.
CD Player
The CD does not play or “no dISC”
lights in the display even when a
CD is in place.
• Make sure that the CD
compartment is closed.
• Place the CD with the label
surface up.
• Clean the CD.
• Take out the CD and leave the CD
compartment open for about an
hour to dry moisture
condensation.
• Make sure "Cd" appears in the
display.
The sound drops out.
• Reduce the volume.
• Clean the CD, or replace it if the
CD is badly damaged.
• Place the player in a location free
from vibration.
• Clean the lens with a
commercially available blower.
• The sound may drop out or noise
may be heard if the CD is
recorded using a personal
computer(CD-R,etc.).
Radio
The audio is weak or has poor
quality.
• Replace all the batteries with new
ones if they are weak.
• Move the player away from the
TV.
The picture of your TV becomes
unstable.
• If you are listening to an FM
program near the TV with an
indoor antenna, move the player
away from the TV.
Tape Player
The tape does not move when you
press an operation button.
• Close the cassette compartment
securely.
The REC z button does not
function or the tape does not play
or record.
• Make sure the safety tab on the
cassette is in place.
• Make sure "TAPE" appears in the
display.
Poor or distorted playback,
recording or erasing quality.
• Clean the heads, pinch roller and
capstan with a cleaning swab
slightly moistened with cleaning
fluid or alcohol.
• Replace all the batteries with new
ones if they are weak.
• TYPE II (high position) or TYPE
IV (metal) tape is being used. Use
TYPE I (normal) tape only.
• Demagnetize the heads using a
commercially available tape head
demagnetizer.
Specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a
distance of about 200 mm from the
objective lens surface on the optical
pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm)
(CLV)
Number of channels
2
Frequency response
20 - 20,000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Pinch roller
Lens
Design and specifications are subject to
change without notice.
Optional accessories
Sony MDR headphone series
WARNING
CD Radio
CassetteCorder
Operating Instructions
To prevent fire or shock
hazard, do not expose the
player to rain or moisture.
To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.
Information
For customers in Europe
Notice for customers in the
United Kingdom
A moulded plug complying with
BS 1363 is fitted to this equipment
for your safety and convenience.
Should the fuse in the plug
supplied need to be replaced, same
rating fuse approved by ASTA or
BSI to BS 1362, (i.e. marked with
or mark) must be used.
If the plug supplied with this
equipment has a detachable fuse
cover, be sure to attach the fuse
cover after you change the fuse.
Never use the plug without the fuse
cover. If you should lose the fuse
cover, please contact your nearest
Sony service station.
Radio section
Frequency range
About this manual
CFD-S22/S32
Record/playback head
Capstan
Erase head
Dimensions
Approx. 420 × 165 × 256 mm (w/h/d)
(16 5⁄8 × 6 1⁄2 × 10 1⁄8 inches) (incl.
projecting parts)
Mass
Approx. 4.1 kg (9 lb. 1 oz) (incl.
batteries)
Supplied accessory
Mains lead (1)
Remote control (1) (CFD-S32/S32L only)
FM
87.5 - 108 MHz
or 87.6 - 108 MHz
AM
531 - 1,602 kHz
CFD-S22L/S32L/922L
FM
87.5 - 108 MHz
MW
531 - 1,602 kHz
LW
153 - 279 kHz
CFD-S22
CFD-S22L
CFD-S32
CFD-S32L
CFD-922L
IF
FM: 10.7 MHz
AM/MW/LW: 450 kHz
Aerials
FM: Telescopic aerial
AM/MW/LW: Built-in ferrite bar
aerial
Sony Corporation © 2000
This Compact Disc player is
classified as a CLASS 1 LASER
product.
The CLASS 1 LASER PRODUCT
label is located on the bottom
exterior.
WARNING
Do not install the appliance in a
confined space, such as a bookcase
or built-in cabinet.
3-043-356-31(1)
The instructions in this manual are
for the CFD-S22, CFD-S22L, CFDS32, CFD-S32L and CFD-922L.
Before you start reading, check
your model number. The CFD-S32L
is the model used for illustration
purposes.
Note
The name of the switch to turn on/
off this player is indicated as below:
“OPERATE”: CFD-S22L/S32L/
922L
“POWER”: CFD-S22/S32
Cassette-corder section
Remote (CFD-S32/S32L only)
The remote does not function.
• Replace all the batteries in the
remote with new ones if they are
weak.
• Make sure that you are pointing
the remote at the remote sensor on
the player.
• Remove any obstacles in the path
of the remote and the player.
• Make sure the remote sensor is
not exposed to strong light such
as direct sunlight or fluorescent
lamp light.
• Move closer to the player when
using the remote.
After trying the above remedies, if
you still have problems, unplug the
mains lead and remove all the
batteries. After all the indications in
the display disappear, plug the
power cord and insert the batteries
again. If the problem persists, please
consult your nearest Sony dealer.
Recording system
4-track 2 channel stereo
Fast winding time
Approx. 120 s (sec.) with Sony cassette
C-60
Frequency response
TYPE I (normal): 70 - 10,000 Hz
General
Speaker
Full range: 10 cm dia., 3.2 ohms, cone
type (2)
Outputs
Headphones jack (stereo minijack)
For 16 - 68 ohms impedance
headphones
Maximum power output
2.3 W + 2.3 W
Power requirements
For CD radio cassette-corder:
Brazilian model:
110 - 120V, 220 - 240V AC
selectable, 50/60 Hz
Other models:
230 V AC, 50 Hz
9 V DC, 6 R20 (size D) batteries
For remote control (CFD-S32/S32L only):
3 V DC, 2 R6 (size AA) batteries
Power consumption
AC 20 W
Battery life
For CD radio cassette-corder:
Choosing Power Sources
Connecting the mains lead
Using the player on batteries
Insert one end of the supplied mains lead to the AC IN socket located at the
rear of the player, and the other end to the mains.
Insert six R20 (size D) batteries (not supplied) into the battery compartment.
Notes
• Replace the batteries when the OPR/BATT indicator dims or when the
player stops operating. Replace all the batteries with new ones. Before
you replace the batteries, be sure to take out the CD from the player.
• To use the player on batteries, disconnect the mains lead from the player.
1
2
Inserting batteries into the remote
(CFD-S32/S32L only)
to AC IN
to the mains
Insert two R6 (size AA) batteries (not supplied)
FM recording
Replacing batteries
Sony R20P: approx. 13.5 h
Sony alkaline LR20: approx. 20 h
Brazilian model only: Adjusting the voltage
Tape playback
Be sure to set the VOLTAGE SELECTOR (at the
bottom) to your local power supply.
Sony R20P: approx. 7.5 h
Sony alkaline LR20: approx. 15 h
CD playback
Sony R20P: approx. 2.5 h
Sony alkaline LR20: approx. 7 h
Tip
Only for the customers supplied with an AC plug adaptor:
Use the supplied AC plug adaptor if the plug of the main lead does not
match your outlet.
With normal use, the batteries should last for about six months. When the
remote no longer operates the player, replace all the batteries with new
ones.
Note
When you operate the player on batteries, you cannot turn on the player
using the remote.
Listening to the radio
Playing a CD
Location of controls
1
Press CD (direct power-on).
Using the display
Shuffle Play
Checking the total track number and playing time
1
Press CD.
2
Press PLAY MODE•MONO/ST until “SHUF” appears in the
display.
1
Play a CD.
Press u to start shuffle play.
2
Press and hold LOOP or FLASH at the point you want to
start the function.
Press DISPLAY ENT•MEMORY in stop mode.
CD
TONE
(CFD-S32/S32L only)
CD compartment
TAPE
Tape
compartment
RADIO BAND
AUTO PRESET
OPR/BATT PLAY MODE
indicator
Z PUSH OPEN/CLOSE
MONO/ST*
Remote Control
(CFD-S32/S32L only)
Total track number
OPERATE
(or POWER)
2
Number buttons
Press DISPLAY ENT•MEMORY while playing a CD.
Press Z PUSH OPEN/CLOSE down to open the CD
compartment and place a CD in the CD compartment.
MODE*
BAND
TUNE +, –
X
N
c
VOL +,–
LOOP
x
., >
FLASH
MEGA BASS
DISPLAY ENT
MEMORY
3
x
i (headphones) jack
Close the CD compartment.
u
Number buttons for
VOLUME +,–
CD/RADIO DIRECT OPERATION
* MODE on the remote has the same function
as PLAY MODE•MONO/ST on the player.
c
* The name of this button is PLAY MODE•MONO/ST for CFD-S22/S32,
PLAY MODE•MONO/ST ISS for CFD-S22L/S32L/922L.
Tip
To listen through headphones, connect the headphones to the
i (headphones) jack.
the current track number and
the remaining time on the current track*
once
the number of tracks left
and remaining time on the CD
twice
4
Press u (N on the remote, CFD-S32/S32L only).
The player plays all the tracks once.
Reinforcing the bass sound
Track number Playing time
To locate
Press
a specific track directly
a number button of the track.
a point while listening
to the sound
> (forward) or . (backward) while
playing until you find the point.
a point while observing
the display
> (forward) or . (backward) in
pause until you find the point.
Tip
When you locate a track numbered over 10, press >10 first, then the
corresponding number buttons.
Example:To play track number 23, press >10 first, then 2 and 3.
Note
You cannot locate a specific track if "SHUF" or "PGM" is lit in the display.
Turn off the indication by pressing x.
HI
the low tone
LO
repeat a selected part of a CD
LOOP on the remote
"flash" the CD sound
FLASH on the remote
Press CD.
2
Proceed as follows:
Do this
a single track
To
Press
adjust the volume
VOLUME +, – (VOL +, – on the remote,
CFD-S32/S32L only)
2 Press the number button for the track
you want to repeat.
stop playback
x
pause playback
u (X on the remote, CFD-S32/S32L only)
Press the button again to resume play after
pause.
go to the next track
>
go back to the previous track
.
remove the CD
Z PUSH OPEN/CLOSE
turn on/off the player
OPERATE (or POWER)
1 Press PLAY MODE•MONO/ST until
“REP ALL” appears.
2 Press u.
tracks in random order
1 Press PLAY MODE•MONO/ST until
“SHUF REP” appears.
2 Press u.
programmed tracks
You can store radio stations into the player’s memory. You can preset up
to 30 radio stations (CFD-S22/S32) or 40 radio stations (CFD-S22L/S32L/
922L), 10 for each band in any order.
1
To cancel the LOOP or FLASH function
1
Press CD.
Release the button.
The player returns to normal play.
2
Press PLAY MODE•MONO/ST until “PGM” appears in the
display.
Notes on CDs
Press the number buttons for the tracks you want to
programme in the order you want. You can arrange the playing
order of up to 20 tracks.
Display
2
• Before playing, clean the CD with a cleaning cloth. Wipe the CD from the
center out.
Display
Display
3
Programmed track
4
Press u to start program play.
To cancel Programme Play
Press PLAY MODE•MONO/ST until “PGM” disappears from the display.
To check the order of tracks before play
Press DISPLAY ENT•MEMORY.
Every time you press the button, the track number appears in the
programed order.
• Do not use solvents such as benzine, thinner, commercially available
cleaners or anti-static spray intended for vinyl LPs.
• Do not expose the CD to direct sunlight or heat sources such as hot air
ducts, nor leave it in a car parked in direct sunlight as there can be a
considerable rise in temperature inside the car.
• Do not stick paper or sticker on the CD, nor scratch the surface of the CD.
• After playing, store the CD in its case.
If there is a scratch, dirt or fingerprints on the CD, it may cause tracking
error.
1 Press PLAY MODE•MONO/ST until
“PGM REP” appears.
2 Press the number buttons for the tracks
you want to programme in the order you
want up to 20 tracks.
3 Press u.
To cancel Repeat Play
Press PLAY MODE•MONO/ST until “REP” disappears from the display.
Hold down RADIO BAND•AUTO PRESET for 2 seconds
until "AUTO" flashes in the display.
Hold down TUNING + or – (TUNE + or – on the remote,
CFD-S32/S32L only) until the frequency digits begin to
change in the display.
Display
Playing order
Press RADIO BAND•AUTO PRESET to select the band.
Display
The player automatically scans the radio frequencies and
stops when it finds a clear station.
If you can't tune in a station, press the button repeatedly
to change the frequency step by step.
Press DISPLAY ENT•MEMORY.
The stations are stored in memory from the lower frequencies
to the higher ones.
Tip
If you automatically preset the "FM1" or "FM2" band, 10 radio stations
are stored in "FM1" band and 10 more radio stations are stored in
"FM2" band.
If a station cannot be preset automatically
You need to preset a station with a weak signal manually.
To
Press
adjust the volume
VOLUME +, – (VOL +, – on the remote,
CFD-S32/S32L only)
turn on/off the radio
OPERATE (or POWER)
1 Press RADIO BAND•AUTO PRESET to select the band.
2 Tune in a station you want.
3 Hold down the number buttons that you want to preset the new station
To improve broadcast reception
on for about 2 seconds.
Display
Reorient the antenna for FM. Reorient the player itself for AM or
MW/LW.
Press x once if the CD is stopped and twice if the CD is playing. The
current program will be erased. Then create a new programme following
the programming procedure.
To repeat
all the tracks
Presetting radio stations
2
Programme Play
To change the current programme
1
1 Press PLAY MODE•MONO/ST until
“REP 1” appears.
Press TONE.
the high tone
Press PLAY MODE•MONO/ST until “SHUF” disappears from the display.
Press RADIO BAND•AUTO PRESET until the band you
want appears in the display (direct power-on).
Each time you press the button, the indication changes as
follows:
CFD-S22/S32: “FM1” n “FM2” n “AM”
CFD-S22L/S32L/922L: “FM1” n “FM2” n “MW” n
“LW”.
CD/RADIO DIRECT OPERATION
c
Press MEGA BASS.
"MEGA BASS" appears in the display.
To return to normal sound, press the button again.
Display
Press and Hold
Repeat Play
Adjusting the sound emphasis (MEGA BASS/TONE)
To enhance
To
Locating a specific track
Display
Adjusting the tone (CFD-S32/S32L only)
To cancel Shuffle Play
3
TONE
SLEEP
OPERATE
(or POWER)
Press DISPLAY ENT•MEMORY
the current track number
three times
and playing time
* For a track whose number is more than 20, the remaining time appears as
“- -:- -” in the display.
With the labeled side up
TUNING –, +
., >
To display
1
You can repeat part of a CD (LOOP) and can "flash" the CD sound (FLASH)
during playback.
Checking the remaining time
FUNCTION
MEGA BASS
3
Total playing time
SLEEP
Enjoying Sound effects (LOOP/FLASH)
(CFD-S32/S32L only)
Tips
• You can play the same program again, since the program is saved until
you open the CD compartment.
• You can record your own program. After you’ve created the programme,
insert a blank tape and press z to start recording.
FM
AM/MW/LW
Tips
• The "FM1" and "FM2" bands have the same functions. You can store the
stations you want separately in "FM1" and "FM2".
• If the FM broadcast is noisy, press PLAY MODE•MONO/ST until
"Mono" appears in the display and the radio will play in monaural.
The new station replaces the old one.
Playing preset radio stations
1
Press RADIO BAND•AUTO PRESET to select the band.
2
Press the number buttons to tune in the stored station.
CD/RADIO DIRECT OPERATION
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement