4-239-335-11 (1) Micro Hi-Fi Component System Operating Instructions Owner’s Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. _______________ CMT-EP303 © 2002 Sony Corporation Serial No. _______________ WARNING WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. This appliance is classified as a CLASS 1 LASER product. This label is located on the bottom. To prevent fire, do not cover the ventilation of the apparatus with newspapers, table-cloths, curtains, etc. And don’t place lighted candles on the apparatus. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. Don’t throw away the battery with general house waste, dispose of it correctly as chemical waste. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. NOTICE FOR THE CUSTOMERS IN THE U.S.A. Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. NOTICE FOR THE CUSTOMERS IN CANADA CAUTION This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION The use of optical instruments with this product will increase eye hazard. 2GB TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. Table of Contents List of Button Locations and Reference Pages Main unit ............................................... 4 Remote control ...................................... 5 Getting Started Hooking up the system .......................... 6 Inserting two size AA (R6) batteries into the remote ........................................ 7 Setting the clock .................................... 7 CD Loading the CD ..................................... 8 Playing the CD — Normal Play/Shuffle Play/Repeat Play .................................................. 8 Programing the CD tracks — Program Play .............................. 9 Tuner Presetting radio stations ....................... 10 Listening to the radio — Preset Tuning ........................... 11 — Manual Tuning ......................... 11 Tape Loading a tape ..................................... 12 Playing a tape ...................................... 12 Recording to a tape — CD Synchro Recording/Recording Manually ....................................... 13 Sound Adjustment Adjusting the sound — MEGA BASS ........................... 14 Turning off the sound — Muting ...................................... 14 Timer Falling asleep to music — Sleep Timer .............................. 14 Waking up to music — Daily Timer .............................. 15 Display Using the CD display .......................... 16 Troubleshooting Problems and remedies ........................ 16 Additional information Precautions .......................................... 18 Specifications ...................................... 19 3GB List of Button Locations and Reference Pages Illustration number How to use this page r Use this page to find the location of buttons and other parts of the system that are mentioned in the text. MUSIC MENU 9 (14) R R Name of button/part Reference page Main unit ALPHABETICAL ORDER A–P Cassette compartment qd (12) CD 4 (8, 9, 13) Display Window 5 (8, 9, 10) ENTER/PGM w; (8, 9, 10, 14) MEGA BASS 8 (14) MUSIC MENU 9 (14) PHONES jack ws PRESET +/– qs (10, 11) 4GB BUTTON DESCRIPTIONS R–Z Remote sensor 0 REPEAT 2 (8) SHUFFLE wa (8) TAPE 3 (12) TIMER indicator 1 (15) TUNER 6 (10, 11, 13) TUNER MEM w; (10) TUNING +/– wd (10, 11) VOLUME control qa @/1 (power) wh (6) CD . m/M > (go back/go forward) wd (8, 9) u (play/pause) wf (8, 9) Z PUSH OPEN/CLOSE 7 (8) x (stop) wg (8, 9) TAPE M (fast forward) qh (12) X (pause) qf (12, 13) N (play) qk (12) z (recording) ql (13) m (rewind) qj (12) xZ (stop/eject) qg (12, 13) Remote control A–P CD/REMAIN ql (7, 8, 9, 13, 15, 16) CLOCK/TIMER + 8 (7, 14, 15) CLOCK/TIMER – qd (7, 14, 15) CLOCK/TIMER/SLEEP SET 1 (7, 14, 15) MEGA BASS qs (14) MUSIC MENU qa (14) MUTING q; (14) PRESET +/– qf (10, 11) BUTTON DESCRIPTIONS R–Z REPEAT 6 (8) SHUFFLE 5 (8) TAPE qk (12) TIMER ON/OFF 2 (15) TUNER/BAND 4 (10, 11, 13) TUNER MEM/ENTER/PGM 7 (7, 9, 10, 14, 15) TUNING + 8 (10, 11) TUNING – qd (10, 11) VOL (volume) +/– 9 m (rewind) M (fast forward) qg (8) . (go back) > (go forward) qg (8, 9) u (play/pause) qh (8, 9) `/1 (power) 3 (6) x (stop) qj (8, 9, 12) List of Button Locations and Reference Pages ALPHABETICAL ORDER 5GB Getting Started Hooking up the system Do the following procedure 1 to 2 to hook up your system using the supplied cords and accessories. FM antenna Front speaker (Right) Front speaker (Left) 1 Connect the front speakers. 2 Connect the power cord to a wall outlet. Connect the speaker cords to the SPEAKER terminals as shown below. Insert only the stripped portion. SPEAKER (IMPEDAN CE USE 4Ω Red (3) ) L R Black (#) 6GB If the supplied adaptor on the plug does not fit your wall outlet, detach it from the plug (only for models equipped with the adaptor). To turn on the system, press [/ 1 (power). Inserting two size AA (R6) batteries into the remote Setting the clock the remote. 3 Press CLOCK/TIMER + or – on the remote repeatedly to set the clock. e E e E 4 Press TUNER MEM/ENTER/PGM on the remote. The clock starts working. Getting Started 1 Turn on the system. 2 Press CLOCK/TIMER/SLEEP SET on To adjust the clock Tip Perform from step 2. When the remote no longer operates the system, replace both batteries with new ones. Note Note The clock settings are canceled when you disconnect the power cord or if a power failure occurs. If you do not use the remote for a long period of time, remove the batteries to avoid possible damage from battery leakage. 7GB CD 2 Press SHUFFLE or ENTER/PGM Loading the CD (TUNER MEM/ENTER/PGM on the remote) repeatedly until the mode you want appears in the display. 1 Press Z PUSH OPEN/CLOSE down to Select open the lid of the CD compartment. To play No display The CD in original order. (Normal Play) 2 Place a CD with the label side up on the compartment. SHUFFLE The tracks on the CD in random (Shuffle Play) order. PROGRAM The tracks on the CD in the order (Program Play) you want them to be played (see “Programing the CD tracks” on page 9). 3 Press u. Other Operations 3 Press Z PUSH OPEN/CLOSE down to close the lid of the CD compartment. Playing the CD — Normal Play/Shuffle Play/Repeat Play This system lets you play the CD in different play modes. Playing time To Do this Stop playback Press x. Pause Press u. Press again to resume play. Select a track Turn ./> clockwise or counterclockwise (or press . or > on the remote). Find a point in a track During play, turn and hold m/ M clockwise or counterclockwise (or keep pressing m or M on the remote). Release it when you find the desired point. Play repeatedly Press REPEAT during play until “REPEAT” or “REPEAT 1” (Repeat Play) appears. REPEAT: For all the tracks on the CD. REPEAT 1: For a single track only. To cancel playing repeatedly, press REPEAT until “REPEAT” or “REPEAT 1” disappears. Track number 1 Press CD (CD/REMAIN on the remote). 8GB Remove the CD Press Z PUSH OPEN/CLOSE. Programing the CD tracks — Program Play You can make a program of up to 28 tracks in the order you want them to be played. To Do this Check the total number of programed tracks Press ENTER/PGM (TUNER MEM/ENTER/PGM on the remote) repeatedly in stop mode. Each time you press the button, the selected track number and the programed step number appear in the display in turn. then place a CD. 2 Press ENTER/PGM (TUNER MEM/ ENTER/PGM on the remote) repeatedly until “00 PR.01” appears in the display. 3 Turn ./> clockwise or counterclockwise (or press . or > on the remote) until the desired track appears in the display. Programed step number Cancel Program Press x twice until “PROGRAM” Play disappears from the display. The program you made will be erased. CD 1 Press CD (CD/REMAIN on the remote), Tip The program you made remains after Program Play finishes. When Program Play remains in the system’s memory, “PROGRAM” flashes. To play the same program again, press CD (CD/REMAIN on the remote) and ENTER/PGM (TUNER MEM/ENTER/ PGM on the remote), then press u. Selected track number (including selected track) 4 Press ENTER/PGM (TUNER MEM/ ENTER/PGM on the remote). The track is programed. The next program step number appears, and “PROGRAM” flashes. 5 To program additional tracks, repeat steps 3 to 4. 6 Press u. Program Play starts. 9GB Tuner 4 Press PRESET + or – until the preset Presetting radio stations You can preset up to 24 stations for FM and AM. You can then tune in any of those stations simply by selecting the corresponding preset number. There are two ways to store the station presets. To Method Automatically tune all of the stations that can be received in your area and then store them manually Automatic Tuning Preset Manually tune and store the radio frequency of your favourite stations Manual Tuning Preset number you want for the station flashes. 5 Press ENTER/PGM (TUNER MEM/ ENTER/PGM on the remote). The station is stored. 6 Repeat steps 1 to 5 to store other stations. Setting presets through manual tuning 1 Press TUNER (TUNER/BAND on the Setting presets through automatic tuning 1 Press TUNER (TUNER/BAND on the remote) repeatedly to select “FM” or “AM”. remote) repeatedly to select “FM” or “AM”. 2 Turn TUNING +/– (or press TUNING + or – on the remote) repeatedly to tune in the desired station. 3 Press TUNER MEM (TUNER MEM/ ENTER/PGM on the remote). A preset number appears in the display. The stations are stored from preset number 1. 2 Turn and hold TUNING +/– (or press and hold TUNING + or – on the remote) until the frequency indication starts to change, then release it. Scanning stops automatically when the system tunes in a station. “STEREO” (for a stereo program) appears. If the scanning doesn’t stop Set the frequency of the desired radio station as described in steps 2 through 6 of “Setting presets through manual tuning”. 3 Press TUNER MEM (TUNER MEM/ ENTER/PGM on the remote). A preset number appears in the display. The stations are stored from preset number 1. Preset number 10GB Preset number 4 Press PRESET + or – repeatedly to select the desired preset number. 5 Press ENTER/PGM (TUNER MEM/ ENTER/PGM on the remote). The station is stored. 6 Repeat steps 1 to 5 to store other stations. 2 Press PRESET + or – repeatedly to tune Other Operations To Do this in the desired preset station. Tune in a station with a weak signal Follow the procedure described in “Setting presets through manual tuning”. The preset number appears in the display for a few seconds. When only one station is preset, only that station is tuned. Change the preset number Start over from step 1. Set another station to an exsisting preset number Start over from step 1. After step 3, press PRESET + or – repeatedly to select the preset number where you want to store the other station and then press ENTER/PGM (TUNER MEM/ENTER/PGM on the remote). — Manual Tuning 1 Press TUNER (TUNER/BAND on the Tuner To change the AM tuning interval (except for the European and Middle Eastern models) Listening to non-preset radio station remote) repeatedly to select “FM” or “AM”. 2 Turn TUNING +/– (or press TUNING + or – on the remote) repeatedly to tune in the desired station. Tip To improve broadcast reception, adjust the antenna (for FM) or reorient the main unit itself (for AM). Disconnect the power cord from the wall outlet first, and then set the AM FREQ STEP switch at the rear to 9 kHz or 10 kHz. Tip The preset stations are retained for half a day even if you unplug the power cord or if a power failure occurs. Listening to the radio You can listen to a radio station either by selecting a preset station, or by manually tuning in the station. Listening to a preset station — Preset Tuning Preset radio stations in the tuner’s memory first (see “Presetting radio stations” on page 10). 1 Press TUNER (TUNER/BAND on the remote). 11GB Tape Loading a tape 1 Press xZ. 2 Insert a tape in deck with the side you want to play/record facing forward. Insert with the side you want to play/ record facing forward. Playing a tape You can use TYPE I (normal) tape. 1 Load a recorded tape. 2 Press TAPE. 3 Press N. 12GB To Press Stop play xZ Pause X Press again to resume play. Fast-forward or rewind m or M Remove the cassette xZ Recording to a tape — CD Synchro Recording/Recording Manually You can record from a CD or radio. You can use TYPE I (normal) tape. Steps Recording from a CD (CD Synchro Recording) Recording from the radio Load a blank tape. 2 Press CD (CD/REMAIN on the remote). Press TUNER (TUNER/BAND on the remote). 3 Load the CD you want to record. Tune in the station you want to record. 4 Press z. Press X and z . Tape 1 The deck stands by for recording. Press X again. To stop recording Press xZ. Tip For recording from a CD to a tape, you can turn ./> clockwise or counterclockwise (or press . or > on the remote) to select tracks before step 4. 13GB Sound Adjustment Timer Adjusting the sound Falling asleep to music — Sleep Timer Reinforcing the bass sound — MEGA BASS You can listen to music with stronger bass tones. You can set the system to turn off after certain amount of time, so that you can fall asleep to music. 1 Press CLOCK/TIMER/SLEEP SET on the remote repeatedly until “SLEEP OFF” appears in the display. Press MEGA BASS. “MEGA BASS” appears in the display and the bass is reinforced. 2 Press CLOCK/TIMER + or – on the Press again to cancel MEGA BASS. remote to select the minutes until the player goes off automatically. Selecting the preset effect from the music menu Every time you press the button, the minute display (the turn-off time) changes as follows: 90 y 80 y 70 y … y 10 y OFF Press MUSIC MENU repeatedly to select the preset effect you desire. Each time you press the button, the display changes cyclically as follows: ROCK t POP t JAZZ t No display t ROCK t ... Turning off the sound — Muting You can turn off the sound temporarily. Press MUTING on the remote. Press again to cancel muting. Tip You can also turn up the volume by turning VOLUME clockwise or turning off the power and turning it on again. 14GB 3 Press TUNER MEM/ENTER/PGM on the remote. To Do this Change the time to turn off Start over from step 1. Cancel the Sleep Timer function Start over from step 1 and select “OFF” on step 2. Waking up to music To Do this Check the setting Press CLOCK/TIMER/ SLEEP SET on the remote repeatedly. — Daily Timer You can wake up to music at a preset time. Make sure you have set the clock (see “Setting the clock” page 7). Change the setting Start over from step 1. Cancel the timer operation Press TIMER ON/OFF on the remote. 1 Prepare the sound source you want to play. • CD: Place a CD. • Radio: Tune in the preset station you want (see “Listening to the radio” on page 11). the remote repeatedly until “ON 0:00” appears in the display. 4 Set the time to start playback using CLOCK/TIMER + or – on the remote. 5 Press TUNER MEM/ENTER/PGM on the remote. 6 Press CLOCK/TIMER/SLEEP SET on the remote repeatedly until “OFF 0:00” appears in the display. Sound Adjustment/Timer 2 Adjust the volume. 3 Press CLOCK/TIMER/SLEEP SET on 7 Set the time to stop playback using CLOCK/TIMER + or – on the remote. 8 Press TUNER MEM/ENTER/PGM on the remote. 9 Press CD/REMAIN or TUNER/BAND on the remote depending on the sound source you want to play. 10 Turn off the power and press TIMER ON/OFF on the remote. The TIMER indicator lights up. 15GB Display Troubleshooting Using the CD display Problems and remedies Press CD/REMAIN on the remote repeatedly. If you have any problem using this system, use the following check list. The display changes as follows: First, check that the power cord is connected firmly and the speakers are connected correctly and firmly. During normal play Elapsed playing Remaining time Remaining time Elapsed playing time on the current track t on the current track t on the current CD t time on the current track t ... Should any problem persist, consult your nearest Sony dealer. General The clock indication does not show the correct time. • A power interruption occurred. Set the clock and timer settings again. The clock setting/radio presetting/timer is canceled. • The power cord is disconnected or a power failure occurs longer than half a day. Redo the following: — “Setting the clock” on page 7 — “Presetting radio stations” on page 10 If you have set the timer, also redo “Waking up to music” on page 15. There is no sound. • Turn VOLUME clockwise and hold. • The headphones are connected. • Insert only the stripped portion of the speaker cord into the SPEAKER terminal. Inserting the vinyl portion of the speaker cord will obstruct the speaker connections. There is severe hum or noise. • A TV or VCR is placed too close to the stereo system. Move the stereo system away from the TV or VCR. The timer does not function. • Set the clock correctly. • When you used the Sleep Timer, the Daily Timer will not turn on the system until the Sleep Timer turns it off. 16GB The remote does not function. • There is an obstacle between the remote and the system. • The remote is not pointing in the direction of the system’s sensor. • The batteries have run down. Replace the batteries. The color irregularity on a TV screen persists. • Turn off the TV set once, then turn it on after 15 to 30 minutes. If the color irregularity still persists, place the speakers farther away from the TV set. Speakers Sound comes from one channel or unbalanced left and right volume. Sound lacks bass. • Check that the speaker’s + and – terminals are connected correctly. CD Player The CD compartment does not close. The tape does not record. • No tape in the cassette compartment. • The tab has been removed from the cassette. • The tape has reeled to the end. The tape does not record nor play or there is a decrease in sound level. • The heads are dirty. Clean them (see “Cleaning the tape heads” on page 19). • The record/playback heads are magnetized. Demagnetize them (see “Demagnetizing the tape heads” on page 19). The tape does not erase completely. • The record/playback heads are magnetized. Demagnetize them (see “Demagnetizing the tape heads” on page 19). There is excessive wow or flutter, or the sound drops out. • The capstans or pinch rollers are dirty. Clean them (see “Cleaning the tape heads” on page 19). Noise increases or the high frequencies are erased. • The record/playback heads are magnetized. Demagnetize them (see “Demagnetizing the tape heads” on page 19). • The CD is not placed properly. The sound drops out. • The lens is dirty. Clean it with a commercially available blower. The CD will not play. • • • • The CD is not lying flat in the CD compartment. The CD is dirty. The CD is inserted label side down. Moisture condensation has built up. Remove the CD and leave the system turned on for about an hour until the moisture evaporates. Tuner Display/Troubleshooting • Check the speaker connection and speaker placement. Tape Deck Noise is heard. • For FM, move the antenna to reduce the noise. For AM, reorient the main unit itself to reduce the noise. Messages The following message may appear in the display during operations. NO DISC • There is no disc on the CD compartment. 17GB Additional information On operation Precautions On operating voltage Before operating the system, check that the operating voltage of your system is identical with the voltage of your local power supply. On safety • The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. • Unplug the system from the wall outlet (mains) if it is not to be used for an extended period of time. To disconnect the cord (mains lead), pull it out by the plug. Never pull the cord itself. • Should any solid object or liquid fall into the component, unplug the stereo system and have the component checked by qualified personnel before operating it any further. • The AC power cord must be changed only at a qualified service shop. • The nameplate is located on the bottom exteror. On placement • Place the unit in a location with adequate ventilation to prevent heat build-up the unit. • Do not place the unit in an inclined position. • Do not place the unit in locations where it is; — Extremely hot or cold — Dusty or dirty — Very humid — Vibrating — Subject to direct sunlight. On heat buildup • Although the unit heats up during operation, this is not malfunction. • Place the unit in a location with adequate ventilation to prevent heat build-up in the unit. If you continuously use this unit at a large volume, the cabinet temperature of the top, side and bottom rises considerably. To avoid burning yourself, do not touch the cabinet. 18GB • If the system is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lens inside the CD player. Should this occur, the system will not operate properly. Remove the CD and leave the system turned on for about an hour until the moisture evaporates. • When you move the system, take out any discs. If you have any questions or problems concerning your stereo system, please consult your nearest Sony dealer. Notes on CDs • Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. • Do not use solvents. • Do not expose the CD to direct sunlight or heat sources. • Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this system. Attempting to do so may damage the system. Do not use such discs. Note on CD-R/CD-RW playback Discs recorded on CD-R/CD-RW drives may not be played back because of scratches, dirt., recording condition or the drive’s characteristics. Besides, the discs, which are not yet finalized at the end of recording cannot be played back. Cleaning the cabinet Use a soft cloth slightly moistened with mild detergent solution. To save a tape permanently To prevent a tape from being accidentally recorded over, break off the cassette tab from side A or B as illustrated. Break off the cassette tab of side A If you later want to reuse the tape for recording, cover the broken tab with adhesive tape. Before placing a cassette in the tape deck Take up any slack in the tape. Otherwise the tape may get entangled in the parts of the tape deck and become damaged. The tape is very elastic. Do not change the tape operations such as play, stop, and fast-winding (etc.) frequently. The tape may get entangled in the tape deck. Cleaning the tape heads Clean the tape heads after every 10 hours of use. Make sure to clean the tape heads before you start an important recording or after playing an old tape. Use separately sold dry-type or wet-type cleaning cassette. For details, refer to the instructions of the cleaning cassette. Demagnetizing the tape heads Demagnetize the tape heads and the metal parts that have contact with the tape every 20 to 30 hours of use with a separately sold demagnetizing cassette. For details, refer to the instructions of the demagnetizing cassette. Amplifier section AUDIO POWER SPECIFICATIONS: (U.S.A. model only) POWER OUTPUT AND TOTAL HARMONIC DISTORTION: with 4 Ω loads both channels driven, from 120 - 10,000 Hz; rates 6 W per channel minimum RMS power, with no more than 10% total harmonic distortion from 250 mW to rated output. Canadian model: Continuous RMS power output (reference) 6+6W (4 Ω at 1 kHz, 10% THD) European model: DIN power output (rated) 4.5 + 4.5 W (4 Ω at 1 kHz, DIN) Continuous RMS power output (reference) 6+6W (4 Ω at 1 kHz, 10% THD) Music power output (reference) 13 + 13 W Additional Information When using a tape longer than 90 minutes Specifications Other model: The following measured at AC 230 V or AC 120 V, 50/60 Hz DIN power output (rated) 4.5 + 4.5 W (4 Ω at 1 kHz, DIN) Continuous RMS power output (reference) 6+6W (4 Ω at 1 kHz, 10% THD) Outputs PHONES: Accepts headphones of (stereo mini jack) 8 Ω or more SPEAKER: Accepts impedance of 4 to 16 Ω CD player section System Laser Frequency response Compact disc and digital audio system Semiconductor laser (λ=780 nm) Emission duration: continuous 20 Hz - 20 kHz (±0.5 dB) continued 19GB Specifications (continued) Tape player section General Recording system Frequency response Power requirements North American model: European model: Australian model: Mexican model: Argentine model: Taiwan model: Other models: 4-track 2-channel stereo 50 - 13 000 Hz (±3 dB), using Sony TYPE I cassette ±0.15% W.Peak (IEC) 0.1% W.RMS (NAB) ±0.2% W.Peak (DIN) Wow and flutter Tuner section FM stereo, FM/AM superheterodyne tuner FM tuner section Tuning range Antenna Intermediate frequency AM tuner section Tuning range Pan-American model: European model: Other models: Antenna Intermediate frequency 87.5 - 108.0 MHz FM lead antenna 10.7 MHz 530 - 1 710 kHz (with the interval set at 10 kHz) 531 - 1 602 kHz (with the interval set at 9 kHz) 531 -1 602 kHz (with the interval set at 9 kHz) 531 - 1 602 kHz (with the interval set at 9 kHz) 530 - 1 710 kHz (with the interval set at 10 kHz) Built-in ferrite bar antenna 450 kHz Speaker Speaker system Speaker units Nominal impedance Dimensions (w/h/d) Mass 20GBSony Corporation Bass-reflex type Full range 10 cm, cone type 4Ω Approx. 145 × 237 × 170 mm Approx. 1.3 kg net per speaker Printed in China Power consumption U.S.A. model: Canadian model: European model: 120 V AC, 60 Hz 230 V AC, 50/60 Hz 230 V AC, 50/60 Hz 120 V AC, 60 Hz 220 - 230 V AC, 50/60 Hz 110 - 120 V AC, 60 Hz 230 V AC, 50/60 Hz Other models: 25 W 25 W 30 W 0.5 W (in the standby mode) 30 W Dimensions (w/h/d): Approx. 145 × 240 × 252 mm Mass: Approx. 2.9 kg Supplied accessories: Remote Commander (1) Batteries (2) Design and specifications are subject to change without notice.