Sony | CPD-101VS | User's Manual | Sony CPD-101VS User's Manual

3-864-163-13 (1)
Trinitron Multimedia
Computer Display
Operating Instructions
CPD-101VS
CPD-201VS
 1998 by Sony Corporation
Owner’s Record
The model and serial numbers are located
at the rear of the unit. Record the serial
number in the space provided below. Refer
to these numbers whenever you call upon
your dealer regarding this product.
Model No.
Serial No.
WARNING
To prevent fire or shock hazard, do
not expose the unit to rain or
moisture.
Dangerously high voltages are
present inside the set. Do not open
the cabinet. Refer servicing to
qualified personnel only.
FCC Notice
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses, and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can
be determined by turning the equipment
off and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
– Reorient or relocate the receiving
antenna.
– Increase the separation between the
equipment and receiver.
– Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced
radio/TV technician for help.
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
2
NOTICE
This notice is applicable for USA/
Canada only.
If shipped to USA/Canada, install
only a UL LISTED/CSA LABELLED
power supply cord meeting the
following specifications:
SPECIFICATIONS
Plug Type
Nema-Plug 5-15p
Cord
Type SVT or SJT,
minimum 3 × 18 AWG
Length
Maximum 15 feet
Rating
Minimum 7 A, 125 V
NOTICE
Cette notice s’applique aux Etats-Unis
et au Canada uniquement.
Si cet appareil est exporté aux EtatsUnis ou au Canada, utiliser le cordon
d’alimentation portant la mention UL
LISTED/CSA LABELLED et
remplissant les conditions suivantes:
SPECIFICATIONS
Type de fiche Fiche Nema 5-15
broches
Cordon
Type SVT ou SJT,
minimum 3 × 18 AWG
Longueur
Maximum 15 pieds
As an ENERGY STAR Partner, Sony
Corporation has determined that this
product meets the ENERGY STAR
guidelines for energy efficiency.
ENERGY STAR is a U.S. registered
mark.
Declaration of Conformity
Model Number : CPD-101VS
CPD-201VS
Trade Name :
SONY
Responsible party :
Sony Electronics Inc.
Address :
1 Sony Drive, Park Ridge,
New Jersey 07656 U.S.A.
Telephone number :
201-930-6970
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
INFORMATION
This product complies with Swedish
National Council for Metrology (MPR)
standards issued in December 1990 (MPR
II) for very low frequency (VLF) and
extremely low frequency (ELF).
INFORMATION
Ce produit est conforme aux normes du
Swedish National Council for Metrology
de décembre 1990 (MPR II) en ce qui
concerne les fréquences très basses (VLF) et
extrêmement basses (ELF).
Hinweis
Dieses Gerät erfüllt bezüglich
tieffrequenter (very low frequency) und
tiefstfrequenter (extremely low frequency)
Strahlung die Vorschriften des „Swedish
National Council for Metrology (MPR)“
vom Dezember 1990 (MPR II).
INFORMACIÓN
Este producto cumple las normas del
Consejo Nacional Sueco para Metrología
(MPR) emitidas en diciembre de 1990 (MPR
II) para frecuencias muy bajas (VLF) y
frecuencias extremadamente bajas (ELF).
Dieses Garät entspricht den folgenden
europäischen EMV-Vorschriften für Betrieb
in Wohngebieten, gewerblicher Gebleten
und Leichtindustriegebieten.
EN55022/1994 Klasse B
EN50082-1/1992
EN61000-3-2/1995
Hinweise
• Aus ergonomischen Gründen wird
empfohlen, die Grundfarbe Blau nicht
auf dunklem Untergrund zu
verwenden (schlechte Erkennbarkeit,
Augenbelastung bei zu geringem
Zeichenkontrast).
• Aus ergonomischen Gründen
(flimmern) sollten nur Darstellungen
bei Vertikalfrequenzen ab 70 Hz (ohne
Zeilensprung) verwendet werden.
• Die Konvergenz des Bildes kann sich
auf Grund des Magnetfeldes am Ort
der Aufstellung aus der korrekten
Grundeinstellung verändern. Zur
Korrektur empfiehlt es sich deshalb,
die Regler an der Frontseite für
Konvergenz so einzustellen, daß die
getrennt sichtbaren Farblinien für Rot,
Grün und Blau bei z.B. der
Darstellung eines Buchstabens zur
Deckung (Konvergenz) gelangen.
Siehe hierzu auch die Erklärungen zu
Konvergenz.
この装置は、情報処理装置等電波障害自
主規制協議会(VCCI)の基準に基づく
クラスB情報技術装置です。この装置
は、家庭環境で使用することを目的とし
ていますが、この装置がラジオやテレビ
ジョン受信機に近接して使用されると、
受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをし
てください。
本製品は、「高調波ガイドライン適合
品」であり、通商産業省資源エネルギー
庁公益事業部作成の家電・汎用品高調波
抑制対策ガイドラインを満たしていま
す。
本製品は社団法人日本電子工業振興協会
が定めた「表示装置の静電気および低周
波電磁界」に関するガイドラインに適合
しております。
3
4
Table of Contents
Introduction ................................................................................. 6
Plug and play ............................................................................................... 6
Precautions ................................................................................... 7
Functions of Controls .................................................................. 9
Getting Started .......................................................................... 11
Installation ................................................................................................. 12
Using Your Display .................................................................... 14
Preset and user modes.............................................................................. 14
Using the tilt-swivel .................................................................................. 15
Damper wire .............................................................................................. 16
Adjustments ............................................................................... 17
Introducing the On-Screen Display ........................................................
Adjusting the sound volume ...................................................................
Adjusting the picture contrast .................................................................
Adjusting the picture brightness ............................................................
Adjusting the picture centering ..............................................................
Adjusting the picture size ........................................................................
Adjusting the geometry ...........................................................................
Selecting the color temperature ..............................................................
Adjusting the convergence (CPD-201VS only) .....................................
Adjusting the screen moiré ......................................................................
Activating screen degauss .......................................................................
Changing the OSD position .....................................................................
Selecting the OSD language ....................................................................
Resetting .....................................................................................................
17
19
21
21
22
23
24
25
26
27
28
29
30
31
Graphic Picture Enhancement (GPE) ......................................... 32
Available GPE modes ............................................................................... 32
Selecting the GPE mode ........................................................................... 33
Power Saving Function ............................................................. 34
Specifications ............................................................................. 35
Troubleshooting ......................................................................... 37
Self-diagnosis function .............................................................. Back cover
5
Introduction
Congratulations on your purchase of a Sony Multimedia CPD-101VS/
201VS display!
This display incorporates over 25 years of Sony experience with Trinitron
display technology, ensuring excellent performance and outstanding
reliability.
This display’s wide scan range (30 – 70 kHz), together with Digital
Multiscan Technology, allows it to sync to any video mode from
standard VGA through VESA 1024 × 768 at 85 Hz (VESA 1280 × 1024 at
60 Hz).
In addition, its four factory-preset color modes give you unprecedented
flexibility in matching on-screen colors to hard copy printouts.
Furthermore, it features:
• Graphic Picture Enhancement function
improves monitor performance to match the application that you are
running.
With the GPE AUTO MODE, you can use “IntelliLight” compatible
software which will maximize the color and brightness of a window
running a multimedia presentation without affecting the brightness
and contrast of text based applications.
• Integrated stereo speakers with Bass Boost
enables you to enjoy excellent sound reproduction via 3.0 W stereo
speakers.
All together, CPD-101VS/201VS delivers incredible performance with
the quality and support you can expect from Sony.
Plug and play
This display complies with DDC™1 and DDC2B which are the Display
Data Channel (DDC) standards of VESA.
When a DDC1 host system is connected, the display synchronizes with
the V. CLK in accordance with the VESA standards and outputs the
EDID (Extended Display Identification Data) to the data line.
When a DDC2B host system is connected, the display automatically
switches to DDC2B communication.
DDC™ is a trademark of Video Electronics Standard Association.
6
Introduction
Precautions
Installation
• Prevent internal heat build-up by allowing adequate air circulation.
Do not place the unit on surfaces (rugs, blankets, etc.) or near
materials (curtains, draperies) that may block the ventilation holes.
• Do not install the unit near heat sources such as radiators or air ducts,
nor in a place subject to direct sunlight, excessive dust, mechanical
vibration or shock.
• Do not place the unit near equipment which generates magnetism,
such as a converter or high voltage power lines.
Maintenance
• Clean the cabinet, glass panel and controls with a soft cloth lightly
moistened with a mild detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent, such as alcohol or benzine.
• Do not rub, touch, or tap the surface of the screen with sharp or
abrasive items, like a ball point pen or a screwdriver, as this type of
contact may result in a scratched picture tube.
Transportation
• Do not discard the carton and packing materials. When transporting
the unit, use these packing materials so that the unit is properly
packaged.
• When carrying the unit, be careful not to get your hands caught
between the display and the tilt-swivel.
Continued to the next page ➔
Precautions
7
Warning on Power Connection
• Use the supplied power cord.
For the customers in U.S.A.
If you do not do this, this display will not conform to mandatory FCC
standards.
For the customers in UK.
If you use the display in the UK, please use the supplied UK cable
with the UK plug.
for 100 to 120 V AC
for 220 to 240 V AC
for 240 V AC only
• Before disconnecting the power cord, wait at least 30 seconds after
turning off the power switch to discharge static electricity from the
CRT display surface.
• After the power has been turned on, the CRT is demagnetized for
approximately 5 seconds. This generates a strong magnetic field
around the bezel which may affect the data stored on magnetic tape or
disks near the bezel. Place such magnetic recording equipment and
tapes/disks at a distance from this unit.
The socket-outlet shall be installed near the equipment and shall be
easily accessible.
8
Precautions
Functions of Controls
Front
1
2
3
45 6
1
2
3
4
5
6
7
8
9
!º
Microphone
Screen
Stereo speakers
¤ Mute button
? Reset switch
GPE button and
indicator
. Volume +/–
buttons
MENU button
> +/– Contrast
buttons
U Power switch
and indicator
7 8 9
!º
—
—
—
Mutes sound (page 20).
Resets adjustments to factory setting (page 31).
Sets GPE mode (page 32).
Adjust speaker volume (page 19). Use to select
items in an OSD.
Displays the OSD menu.
Adjust picture contrast (page 21). Use to adjust
items in an OSD.
Turns the display on and off.
Functions of Controls
9
Rear
!¡
!™
!∞
!£
!§
!¢
!¶
!¡
!™
AC IN connector
2 Audio plug (green)
!£
h MIC plug (red)
!¢
; Video signal cable
(blue)
2 Headphones jack
!∞
!§
!¶
10
Tilt-Swivel
Subwoofer output
jack
Functions of Controls
Connect the supplied power cord (page 13).
Connect to the computer’s audio output
(page 12).
Connect to the computer’s microphone input
(page 12).
Connect to the computer’s video output
(page 12).
Connect standard mini-plug headphones (not
supplied). The speakers are turned off when
headphones are connected.
Adjusts the angle of the display (page 15).
Connect to a subwoofer’s input (not supplied).
Getting Started
Before using this display, please make sure that the following items are
included in your package:
• Multimedia computer display (1)
• Power cord (1)
• Warranty card (1)
• Operating instructions manual (1)
• Windows Monitor Information Disk and its instruction manual (1)
✎ Tip
This display will sync with any IBM or compatible system equipped with VGA1) or greater
graphics capability. Although this display will sync to other platforms running at horizontal
frequencies between 30 and 70 kHz, including Macintosh2) and Power Macintosh systems, a
cable adapter is required. Please consult Sony Technical Support for advice on which adapter is
suitable for your needs.
1) VGA is a trademark of IBM Corporation.
2) Macintosh is a trademark of Apple Computer Inc.
Continued to the next page ➔
Getting Started
11
Installation
p Step 1: Connect the computer
With the computer switched off, connect the video signal cable to the
display (VGA) connector on your computer. If your computer supports
the DDC plug-and-play standard, this connection will enable DDC
communication between the display and the computer.
The video signal cable is combined with audio and microphone cables.
If your computer is equipped with sound capability, connect the audio
(green) and microphone (red) plugs to appropriate jacks located on your
computer.
2
PRINTER
Blue (to monitor
connector)
AL
USB
CONTR
MONITOR
LINE OUT LINE IN
Green (to LINE OUT
connector)
MIC
Fasten the
screw of the
blue plug.
Red (to microphone
connector)
Computer
✔
Note on handling the video signal cable
Do not touch the pins of the video signal cable.
12
Getting Started
p Step 2: Connect the power cord
With the display switched off, connect the power cord to the display
and the other end to a power outlet.
to a power outlet
Power cord (supplied)
p Step 3: Turn on the display, and then your
computer.
For proper Plug and Play recognition, turn on the display before you
turn on your computer.
✔
Note on Warning Messages
If there is something wrong with the input signal, one of the following messages appears.
“OUT OF SCAN RANGE”
This indicates that the input signal is not supported by the display’s specifications.
“NO INPUT SIGNAL”
This indicates that video signal is missing.
To solve these problems, see “Troubleshooting” on page 37.
p Step 4: If necessary...
Adjust the user controls according to your personal preference.
The installation of your display is complete. Enjoy your display.
Getting Started
13
Using Your Display
Preset and user modes
The Multimedia CPD-101VS/201VS display has factory preset modes for
the 9 most popular industry standards for true “plug and play”
capability.
For less common modes, its Digital Multiscan Technology will perform
all of the complex adjustments necessary to ensure a high quality picture
for any timing between 30 and 70 kHz.
NO.
Resolution
(dots × lines)
640 × 400
640 × 480
640 × 480
800 × 600
800 × 600
1024 × 768
1024 × 768
1152 × 864
1280 × 1024
1
2
3
4
5
6
7
8
9
Horizontal
Frequency
31.5 kHz
31.5 kHz
43.3 kHz
37.9 kHz
46.9 kHz
60.0 kHz
68.7 kHz
54.8 kHz
64.0 kHz
Vertical
Frequency
70 Hz
60 Hz
85 Hz
60 Hz
75 Hz
75 Hz
85 Hz
60 Hz
60 Hz
✔Note for Windows
®
95/98 users
To maximize the potential of your display, install the new model information file from the
supplied Windows® Monitor Information Disk onto your PC.
This display complies with the “VESA DDC” Plug & Play standard. If your PC/graphics board
complies with DDC, select “Plug & Play Monitor (VESA DDC)” or this display’s model name as
the monitor type in the “Control Panel” of Windows® 95/98. If your PC/graphics board has
difficulty communicating with this display, load the Windows® Monitor Information Disk and
select this display’s model name as the monitor type.
Windows® is a registered trademark of Microsoft Corporation in the United States and other
countries.
✔
Note on recommended horizontal timing conditions
Horizontal sync width should be more than 1.0 µsec.
Horizontal blanking width should be more than 3.6 µsec.
14
Using Your Display
p To enter new timings
When using a video mode that is not one of the 9 factory preset modes,
some fine tuning may be required to optimize the display to your
preferences. Simply adjust the display according to the adjustment
instructions. The adjustments will be stored automatically and recalled
whenever that mode is used.
A total of 16 user-defined modes can be stored in memory. If a 17th mode
is entered, it will replace the first.
Using the tilt-swivel
With the tilt-swivel, this unit can be adjusted to be viewed at your
desired angle within 90° horizontally and 7° vertically.
To turn the unit vertically and horizontally, hold it at its bottom with
both hands.
Be careful not to get your hands caught between the display and the tiltswivel.
45˚
7˚
45˚
Using Your Display
15
Damper wire
Using a white background, a very thin horizontal line on the screen may
be visible as shown below. This line is the damper wire.
The Trinitron tube has a vertically striped Aperture Grille inside. The
Aperture Grille allows more light to pass through to the screen giving
the Trinitron CRT more color and brightness.
The damper wire is attached to the Aperture Grille to prevent vibration
of the Aperture Grille wire so that the screen image is constantly stable.
Approx. 6 cm (2 3/8 inches)
(CPD-201VS only)
Damper wires
Approx. 6 cm
(2 3/8 inches)
16
Using Your Display
Adjustments
When one of the preset-type signals is input, no picture adjustment is
necessary.
You can, however, adjust the picture to your preference by following the
procedure described below.
To adjust the display, turn on the display and computer.
Introducing the On-Screen Display
Beyond sound volume and picture contrast adjustment, most
adjustments are made using the OSD menu system.
Using the OSD menu
1. Press the MENU button to display the MENU OSD.
MENU
OK
MENU
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
2. Use the the four arrow (>/./?//) buttons (. +/– and > +/–
buttons) to select the item you want to adjust.
Change the item from blue to yellow.
MENU
OK
MENU
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
3. Press the MENU button again.
The item is selected and the item’s OSD appears.
BRIGHT/CONTRAST
50
BRIGHTNESS
Adjustments
17
Summary of each item
1
2
MENU
9
8
3
OK
MENU
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
7
6
5
4
1 COLOR
Selects the color temperature.
2 CENTER
Adjusts the picture centering.
3 SCREEN
Reduces the moiré pattern.
Adjusts the vertical and horizontal convergence (CPD-201VS only).
4 ZOOM
Adjusts the picture size in horizontal and vertical direction
proportionally.
5 OPTION
Activates bass-boost and screen degauss, changes the OSD position
and selects the OSD language.
6 SIZE
Adjusts the picture size. You can adjust the size in horizontal or
vertical direction individually.
7 GEOM
Adjusts the picture rotation, pincushion, etc.
8 BRIGHT
Adjusts the picture brightness and contrast.
9 EXIT
Closes the OSD menu.
18
Adjustments
Adjusting the sound volume
1. Press the . + or – button.
The VOLUME/CONTRAST OSD appears.
The horizontal and vertical frequencies for each input signal received
appear.
VOLUME/CONTRAST
26
65. 0kHz /
Horizontal
frequency
26
76Hz
Vertical
frequency
2. Press the . +/– buttons to adjust volume.
+ to increase volume
– to decrease volume
The VOLUME/CONTRAST OSD disappears three seconds after you
release the buttons.
✎ Tips
• Adjust the volume while listening to the sound.
• Excessively high volume may cause howling.
p To activate Bass Boost for rich bass sound
1. Select OPTION in the MENU OSD and press the MENU button.
The OPTION OSD appears.
MENU
OK
MENU
OPTION
OFF
ON
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
BASS BOOST
Continued to the next page ➔
Adjustments
19
2. Select BASS BOOST with the >/. buttons.
3. Press the / button to select ON.
To cancel bass boost, press the ? button to select OFF.
OPTION
OFF
ON
BASS BOOST
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
p To mute the sound
Press the ¤ button. The ¤ indicator appears while the sound is muted.
Press again to cancel muting.
You can cancel muting also by pressing the . + button.
✎ Tip
¤ appears instead of . on the VOLUME/CONTRAST OSD while the sound is muted.
20
Adjustments
Adjusting the picture contrast
The adjustment data becomes the common setting for all input signals.
1. Press the > + or – button.
The VOLUME/CONTRAST OSD appears.
The horizontal and vertical frequencies for each input signal received
appear.
VOLUME/CONTRAST
26
65. 0kHz /
Horizontal
frequency
26
76Hz
Vertical
frequency
2. Press the > +/– buttons to adjust the picture contrast.
+ for more contrast
– for less contrast
The VOLUME/CONTRAST OSD disappears three seconds after you
release the buttons.
Adjusting the picture brightness
The adjustment data becomes the common setting for all input signals.
1. Select BRIGHT in the MENU OSD and press the MENU button.
The BRIGHT/CONTRAST OSD appears.
MENU
OK
MENU
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
BRIGHT/CONTRAST
50
BRIGHTNESS
Continued to the next page ➔
Adjustments
21
2. Press the ?// buttons to adjust the picture brightness.
/ for more brightness
? for less brightness
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons the OSD automatically disappears after 30 seconds.
Adjusting the picture centering
The adjustment data becomes the individual setting for each input signal
received.
1. Select CENTER in the MENU OSD and press the MENU button.
The CENTER OSD appears.
MENU
OK
MENU
CENTER
COLOR CENTER SCREEN
73
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
26
2. For vertical adjustment
Press the >/. buttons.
> to move up
. to move down
To exit the OSD
Press the MENU button again.
22
Adjustments
For horizontal adjustment
Press the ?// buttons.
/ to move right
? to move left
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
Adjusting the picture size
The adjustment data becomes the individual setting for each input signal
received.
To adjust the picture size in horizontal and vertical direction
proportionally
1. Select ZOOM in the MENU OSD and press the MENU button.
The ZOOM OSD appears.
MENU
OK
MENU
ZOOM
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
H
V
74
49
2. Press the ?// buttons for the best size.
To adjust the picture size in horizontal or vertical direction
1. Select SIZE in the MENU OSD and press the MENU button.
The SIZE OSD appears.
MENU
OK
MENU
SIZE
COLOR CENTER SCREEN
73
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
26
Continued to the next page ➔
Adjustments
23
2. For vertical adjustment
Press the >/. buttons.
> to increase
. to decrease
For horizontal adjustment
Press the ?// buttons.
/ to increase
? to decrease
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
Adjusting the geometry
The rotation adjustment data becomes the common setting for all input
signals. All other data becomes the individual setting for each input
signal received.
1. Select GEOM in the MENU OSD and press the MENU button.
The GEOMETRY OSD appears.
MENU
OK
MENU
GEOMETRY
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
26
ROTATION
2. Press the >/. buttons to select the item you want to adjust.
24
Adjustments
3. Press the ?// buttons to adjust.
ROTATION
/ to rotate the picture
clockwise
? to rotate
counterclockwise
PINCUSHION
/ to bend both
sides outward
? to bend inward
PIN BALANCE
/ to bend both sides
to the right
? to the left
KEYSTONE
/ to widen the top
? to shrink the top
KEY BALANCE
/ to move the top to
the right
? to the left.
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
Selecting the color temperature
The selected color temperature becomes the common setting for all input
signals.
1. Select COLOR in the MENU OSD and press the MENU button.
The COLOR OSD appears.
MENU
OK
MENU
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
COLOR
11000K
9300K
6500K
5000K
Continued to the next page ➔
Adjustments
25
2. Select the desired color temperature with the >/. buttons.
11000K for the brightest white
9300K for TV white
6500K for video monitor white
5000K for printing paper white
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
Adjusting the convergence
(CPD-201VS only)
Adjust the convergence to eliminate red or blue shadows that may
appear around letters or lines on the screen.
The adjustment data becomes the common setting for all input signals.
1. Select SCREEN in the MENU OSD and press the MENU button.
The SCREEN OSD appears.
MENU
OK
SCREEN
MENU
COLOR CENTER SCREEN
BRIGHT
EXIT
26
ZOOM
H CONVERGENCE
GEOM
SIZE
OPTION
2. Select H (horizontal) CONVERGENCE or V (vertical)
CONVERGENCE with the >/. buttons.
SCREEN
SCREEN
26
H CONVERGENCE
26
Adjustments
26
V CONVERGENCE
3. Press the ?// buttons to shift the red or blue shadows
horizontally or vertically until they disappear.
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
Adjusting the screen moiré
This adjustment is to eliminate wavy or elliptical lines that may appear
on the screen.
The adjustment data becomes the common setting for all input signals.
1. Select SCREEN in the MENU OSD and press the MENU button.
The SCREEN OSD appears. (The convergence icons appear for
CPD-201VS only.)
MENU
OK
SCREEN
MENU
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
26
H CONVERGENCE
2. Select CANCEL MOIRE with the >/. buttons.
3. Press the / button to select ON.
The MOIRE ADJUST icon appears under the CANCEL MOIRE icon.
SCREEN
OFF
ON
CANCEL MOIRE
Continued to the next page ➔
Adjustments
27
4. Press the . button to select MOIRE ADJUST.
SCREEN
26
MOIRE ADJUST
5. Press the ?// buttons to tune the moiré cancellation effect.
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
✔
Note on the moiré cancellation effect
When CANCEL MOIRE is set to ON, the picture may appear fuzzy. If you set CANCEL
MOIRE to OFF, the picture may be clearer, but the moiré will reappear.
Activating screen degauss
The display screen is automatically degaussed (demagnetized) when the
power is turned on.
To manually degauss the screen, do as follows. If you need to degauss
the screen a second time, wait at least 20 minutes for the best result.
1. Select OPTION in the MENU OSD and press the MENU button.
The OPTION OSD appears.
MENU
OK
MENU
OPTION
OFF
ON
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
BASS BOOST
28
Adjustments
2. Select MANUAL DEGAUSS with the >/. buttons.
OPTION
ON
MANUAL DEGAUSS
3. Press the / button to activate the degauss cycle.
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
Changing the OSD position
1. Select OPTION in the MENU OSD and press the MENU button.
The OPTION OSD appears.
MENU
OK
MENU
OPTION
OFF
ON
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
BASS BOOST
2. Select OSD H (horizontal) POSITION or OSD V (vertical) POSITION
with the >/. buttons.
OPTION
OPTION
OSD H POSITION
OSD V POSITION
Continued to the next page ➔
Adjustments
29
3. Press the ?// buttons to move the OPTION OSD to the desired
position.
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
Selecting the OSD language
English, French, German, Spanish and Japanese version of the OSDs are
available.
1. Select OPTION in the MENU OSD and press the MENU button.
The OPTION OSD appears.
MENU
OK
OPTION
MENU
OFF
ON
COLOR CENTER SCREEN
BRIGHT
EXIT
ZOOM
GEOM
SIZE
OPTION
BASS BOOST
2. Select LANGUAGE with the >/. buttons.
OPTION
ENG FRA DEU
ESP
LANGUAGE
30
Adjustments
3. Press the ?// buttons to select the desired language.
To exit the OSD
Press the MENU button again.
✎
Tip
If you don’t touch any buttons, the OSD automatically disappears after 30 seconds.
Resetting
p To recall the factory settings for an individual
adjustment item
1. Select the item you want to reset.
First select the OSD containing the item in the MENU OSD, and then
select the item in the OSD.
2. Press the ? button while the OSD of the item is on.
Only the item highlighted in yellow returns to the factory setting.
p To recall the factory settings for the current
video mode
Press the ? button while no OSD is displayed.
p To recall the factory settings for all modes
Press and hold the ? button for more than two seconds.
All adjustments return to the factory settings.
Adjustments
31
Graphic Picture Enhancement (GPE)
Available GPE modes
Graphic Picture Enhancement is a function designed for your viewing
comfort.
There are four GPE modes: AUTO, MODE 1, MODE 2 and OFF.
The default setting is “AUTO.”
p AUTO mode
This mode is effective only with “IntelliLight” compatible applications.
When an image playback window with “IntelliLight” coding appears on
the screen, the display senses the exact location and size of the window
and applies a higher brightness and sharpness effect to images inside the
window, while the rest of the screen remains at standard picture quality.
For inquiries about “IntelliLight” and compatible software, check Sony’s
web site (www.ita.sel.sony.com) or call Sony Technical Support (1-8884SONYPC).
“IntelliLight” is a trademark of Sony Electronics Inc.
Window with “IntelliLight” coding has
higher brightness and sharpness.
Standard picture quality
✔
Note on the AUTO mode
If one of the four corners of the “IntelliLight” window is covered or if the window goes
beyond the screen border, the GPE effect turns off.
✎ Tip
You can adjust the picture contrast or brightness of the screen outside of the “IntelliLight”
window. The “IntelliLight” window always remains clear and sharp regardless of the
adjustments made to the rest of the screen.
p MODE 1
Higher contrast is applied across the entire screen. MODE 1 is designed
to enhance still image presentations.
✔
Note on MODE 1
Whenever the screen resolution is changed, power saving activated, or power turned off,
MODE 1 is cancelled and GPE returns to the AUTO mode.
32
Graphic Picture Enhancement (GPE)
p MODE 2
Higher contrast and sharpness is applied across the entire screen.
MODE 2 is designed to enhance graphic games and movie/video
presentations.
✔
Note on MODE 2
Whenever the screen resolution is changed, power saving activated, or power turned off,
MODE 2 is cancelled and GPE returns to the AUTO mode.
✎ Tip
MODE 2 may produce ghost images when displaying text oriented applications. In this
case, select the AUTO or OFF mode.
p GPE OFF mode
Screen sharpness and brightness are set to standard quality without any
additional enhancements. This mode is suited for text-based
applications.
✔
Note on the GPE OFF mode
Once OFF mode is selected, GPE status stays in the OFF mode until you manually select
other GPE modes.
Selecting the GPE mode
Press the GPE button repeatedly until the screen message of the desired
mode is displayed.
Each time you press the GPE button, the GPE mode changes as follows:
n
AUTO n GPE OFF n MODE 1 n MODE 2
AUTO
Appears for three seconds
The GPE indicator lights up when AUTO, MODE 1 or MODE 2 is
selected.
Graphic Picture Enhancement (GPE)
33
Power Saving Function
This display meets the power saving guidelines set by the International
ENERGY STAR Program. It is capable of reduced power consumption
when used with a computer equipped with Display Power Management
Signaling (DPMS). By sensing the absence of the sync signal coming
from the computer, it will reduce the power consumption as follows:
✔
CAUTION
The Power Saving function will automatically put the display into Deep Sleep mode if the
power switch is turned on without any vertical or horizontal sync signal from the
computer. Once the horizontal and vertical syncs are sensed, the display will automatically
return to its Normal Operation mode. Note that the power saving function may not work
properly if the video signal contains a “Sync on Green” signal.
1 Normal
Operation
2 Sleep
Power
consumption
CPD-101VS: 110 W (max)
CPD-201VS: 120 W (max)
15 W (max)
Recovery
time
—
U Power
indicator
Green
Approx. 3 sec.
3 Deep Sleep
4 Power-off
8 W (max)
0W
Approx. 10 sec.
—
Green ˜
Orange
Orange
Off
Mode
34
Power Saving Function
Specifications
Picture tube
CPD-101VS:
0.25 mm aperture grille pitch,
15 inches measured diagonally (14.0” viewable),
90-degree deflection, AR coating
CPD-201VS:
0.25 mm aperture grille pitch,
17 inches measured diagonally (16.0” viewable),
90-degree deflection, AR coating
Viewable image size
CPD-101VS:
Approx. 285 × 214 mm (w/h) (11 1/4 × 8 1/2 inches)
14.0” viewing image (measured diagonally)
CPD-201VS:
Approx. 327 × 241 mm (w/h) (12 7/8 × 9 1/2 inches)
16.0” viewing image (measured diagonally)
Max. resolution
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
VESA standards 640 × 480 at 85 Hz
800 × 600 at 85 Hz
1024 × 768 at 85 Hz
1280 × 1024 at 60 Hz
Deflection frequency
Horizontal: 30 to 70 kHz
Vertical: 50 to 120 Hz
Speaker
Left, right: 3.0 W x 2
50 Hz – 20 kHz
Microphones
Uni-directional, electret condenser microphone
Microphones output
3.5 mm miniplug
Audio input
3.5 mm Stereo miniplug, input impedance 47 kΩ,
input level 0.7 Vrms typical
Headphones output
Stereo minijack, 15 mW + 15 mW at 16 Ω
Subwoofer output 3.5 mm miniplug, volume variable
Continued to the next page ➔
Specifications
35
Controls
Front panel direct:
Audio volume/Contrast/Audio mute/GPE (AUTO/
off/mode 1/mode 2)
OSD menu:
Brightness/Contrast/Picture size/Picture zoom/
Picture centering/Convergence (CPD-201VS only)/
Sceen moiré/Color temperature (5000K/6500K/
9300K/11000K)/Rotation/Pincushion/Pin balance/
Keystone/Key balance/Bass boost/Manual
Degauss/OSD position/OSD language
AC input voltage/current
CPD-101VS: 100 to 240 V, 50 – 60 Hz, 1.1 – 0.6 A
CPD-201VS: 100 to 240 V, 50 – 60 Hz, 1.5 – 0.6 A
Power consumption
CPD-101VS: Max. 110 W
CPD-201VS: Max. 120 W
Dimensions
CPD-101VS:
Approx. 368 × 408 × 388 mm (w/h/d)
(14 1/2 × 16 1/8 × 15 3/8 inches)
CPD-201VS:
Approx. 415 × 451 × 423 mm (w/h/d)
(16 3/8 × 17 7/8 × 16 3/4 inches)
Mass
CPD-101VS: Approx. 15.3 kg (33 lb 12 oz)
CPD-201VS: Approx. 19.6 kg (43 lb 3 oz)
Design and specifications are subject to change without notice.
36
Specifications
Troubleshooting
This section may help you isolate a problem and as a result, eliminate the
need to contact technical support, allowing continued productivity.
No picture
If the U indicator is not lit
m Check that the power cord is properly connected.
m Check that the U switch is in the “on” position.
If the “NO INPUT SIGNAL” message appears on the screen, or if the U
indicator is either orange or alternating between green and orange
m Try pressing any key on the computer keyboard.
m Check that your computer power switch is in the “on” position.
m Check that the video signal cable is properly connected and all plugs
are firmly seated in their sockets.
m Ensure that no pins are bent or pushed in the HD15 video input
connector.
If the “OUT OF SCAN RANGE” message appears on the screen
m Check that the video frequency is within that specified for the display.
Horizontal: 30 – 70 kHz
Vertical: 50 – 120 Hz
Refer to your computer’s instruction manual to adjust the video
frequency range.
m If you are using a video signal cable adapter, check that it is the correct
one.
If no message is displayed and the U indicator is green or flashing orange
m See “Self-diagnosis function” (Back cover).
No sound from speaker
If the ¤ indicator is displayed
m Press the ¤ button to cancel muting.
m
m
m
m
Check that the audio plug is properly connected.
Adjust the volume with . +/– buttons.
Check that the headphones are not connected.
Check the volume control, muting, sound selector, etc. of the sound
board. (See the computer’s manual.)
Microphone mixing is not possible
m Check that the MIC plug is properly connected.
m Check the microphone control, sound selector, etc. of the sound board.
(See the computer’s manual.)
Continued to the next page ➔
Troubleshooting
37
Howling (feedback) is heard
m Decrease the volume with . +/– buttons, or turn down the
microphone input volume of the sound board.
Picture is scrambled
m Check your computer manual for the proper display setting.
m Check this manual and confirm that the graphic mode and the
frequency you are trying to operate is supported. Even if the
frequency is within the proper range, some video boards may have a
sync pulse that is too narrow for the display to sync correctly.
Color is not uniform
m Degauss the display (page 28).
If you place equipment which generates a magnetic field, such as a
speaker, near the display, or you change the direction of the display,
color may lose uniformity. The degauss function demagnetizes the
metal frame of the CRT to obtain a neutral field for uniform color
reproduction. If a second degauss cycle is needed, allow a minimum
interval of 20 minutes for the best result.
Screen image is not centered or sized properly
m Adjust the size or centering (pages 22, 23).
m Some video modes do not fill the screen to the edge. This problem
tends to occur with certain video boards.
Edges of the image are curved
m Adjust the geometry (page 24).
Lines or letters show red or blue shadows at edges
m Adjust the convergence (page 26).
Picture is fuzzy
m Adjust the contrast and brightness (page 21). Some brands of video
boards have an excessive video output level which creates a fuzzy
picture at maximum contrast.
m Degauss the display (page 28).
If you place equipment which generates a magnetic field, such as a
speaker, near the display, or you change the direction of the display,
color may lose uniformity. The degauss function demagnetizes the
metal frame of the CRT to obtain a neutral field for uniform color
reproduction. If a second degauss cycle is needed, allow a minimum
interval of 20 minutes for the best result.
m If moiré is cancelled, the picture may become fuzzy. Decrease the
moiré cancellation effect (page 27).
m If the GPE mode is set to AUTO, change it to OFF (page 33).
38
Troubleshooting
Picture bounces or has wavy oscillations
m Isolate and eliminate any potential sources of electric or magnetic
fields. Common causes for this symptom are electric fans, fluorescent
lighting, laser printers, etc.
m If you have another display close to this display, increase the distance
between them to reduce interference.
m Try plugging the display into a different AC outlet, preferably on a
different circuit.
Picture is flickering
m Set the refresh rate on the computer to obtain the best possible picture
by referring to your computer’s manual.
m If the GPE mode is set to AUTO, change it to OFF (page 33).
Picture appears to be ghosting
m Eliminate the use of video extensions and/or video switch boxes if
this symptom occurs. Excessive cable length or weak connections can
produce this symptom.
m If the GPE mode is set to AUTO, change it to OFF (page 33).
m If the GPE mode is set to MODE 2, the picture may appear to be
ghosting. Set to another GPE mode (page 33).
Wavy or elliptical (moiré) pattern is visible
m Cancel the moiré (page 27).
The moiré may be modified depending on the connected computer.
m Due to the relationship between resolution, display dot pitch and the
pitch of some image patterns, certain screen backgrounds sometimes
show moiré. Change your desktop pattern.
IntelliLight does not work
m Check that all four corners of the “IntelliLight” window are clearly
displayed and are not covered by another window.
m Check that the GPE mode is set to AUTO (page 33).
m Leave the display’s power “on” and reboot your computer.
m IntelliLight does not work correctly with an interlaced video mode.
Check the vertical refresh rate in the Properties window of Windows
95/98 and select a non-interlaced mode.
Tiny color bars appear in the corners of the IntelliLight window
m Set the GPE mode to AUTO (page 33).
m Check that all four corners of the “IntelliLight” window are clearly
displayed and are not covered by another window.
Troubleshooting
39
A fine horizontal line (wire) is visible
m This wire stabilizes the vertically striped Aperture Grille (page 16).
This Aperture Grille allows more light to pass through to the screen
giving the Trinitron CRT more color and brightness.
Hum is heard right after the power is turned on
m When the power is turned on, the Auto-degauss cycle is activated.
While the Auto-degauss cycle is activated, a hum may be heard. The
same hum is heard when the display is manually degaussed. This is
not a malfunction.
• If the problem persists, call your authorized Sony dealer from a
location near you, or call Sony Technical Support at 1-888-4SONYPC
(1-888-476-6972).
• Note the model name and the serial number of your display. Also note
the make and name of your computer and video board.
Self-diagnosis function
This display is equipped with a self-diagnosis function. Use this function
if there is a problem with your display or computer.
1. Disconnect the video input cable or turn off the connected computer.
2. Turn the display off and on.
3. Press and hold the >/ button for more than 2 seconds.
If all four color bars appear (white, red, green, blue) after a few seconds,
the display is working properly, but there might be a problem with your
computer. Contact your computer’s manufacturer.
If the color bars do not appear, there might be a problem with the
display. Contact your local authorized Sony dealer, or call Sony Technical
Support at 1-888-4SONYPC (1-888-476-6972).
Sony Corporation Printed in Japan
Download PDF

advertising