Sony CPD-210GS Operating instructions

Sony CPD-210GS Operating instructions
SONY
Trinitron' Color
Computer Display
Operating Instructions
CPD-110GS
CPD-210GS
98 by Sony Corporation
Owner’s Record
The modet and serial numbers are located at the rear of the unit.
Record these numbers in the spaces provided below. Refer to them
whenever you call upon your dealer regarding this product.
Model No. Serial No.
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
Dangerously high voltages are present inside the
unit. Do not open the cabinet. Refer servicing to
qualified personnel only.
FCC Notice
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
hamtul interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
~ Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment.
IMPORTADOR (Para Mexico unicamente/For Mexico only)
Sony Electronicos de Mexico, S.A. de C.V.
Henty -ord No.25
Fraccionamiento San Nicolas, Tialnepantla
Estado de Mexico, CP54030
Tel.: 321-1000
R.F.C. SEM-941001-BJA
Hinweise
* Aus ergonomischen Grúnden wird empfohien, die
Grundfarbe Biau nicht auf dunklem Untergrund zu verwenden
(schlechte Erkennbarkeit, Augenbelastung bei zu geringem
Zeichenkontrast).
* Aus ergonomischen Gründen (fimmer ten nur
Darstellungen bei Vertikalfrequenzen =: Hz (ohne
Zeilensprung) verwendet werden.
* Die Konvergenz des Bildes kann sich = rund des
Magnetfeldes am Ort der Aufstellung a ¡er korrekten
Grundeinsteliung verándem. Zur Kor:: empfiehlt es sich
deshalb, die Regler an der Frontseite .onvergenz so
einzustellen, daG die getrennt sichtba: rarblinien fir Rot,
Gran und Blau bei 2.8. der Darstell: © snes Buchstabens
zur Deckung (Konvergenz) gefanas
Siehe hierzu auch die Erklárunge:. Konvergenz.
NOTICE
This notice is applicable for USA/Canada only.
If shipped to USA/Canada, install only a UL LISTED/CSA
LABELLED power supply cord meeting the following
specifications:
SPECIFICATIONS
Plug Type Nema-Plug 5-15p
Cord Type SVT or SJT, minimum 3 x 18 AWG
Length Maximum 15 feet
Rating Minimum 7 A, 125 V
NOTICE
Cette notice s'applique aux Etats-Unis et au Canada
uniquement.
Si cet appareit est export* aux Etats-Unis ou au Canada,
utiliser le cordon d'alimentation portant la mention UL LISTED/
CSA LABELLED et remplissant les conditions suivantes:
SPECIFICATIONS
Type de fiche Fiche Nema 5-15 broches
Cordon Type SVT ou SJT, minimum 3 x 18 AWG
Longueur Maximum 15 pieds
Tension Minimum 7 A, 125 V
UT TATI =="
6 U
= EG MI
MM 7 O
IMPORTANTE
Para prevenir cualquier mal funcionamiento y evitar daños, por
favor, lea detalladamente este manual de instrucciones antes
de conectar y operar este equipo.
INFORMATION
This product complies with Swedish National Council for Metrology
(MPR) standards issued in December 1990 (MPR II) for very low
frequency (VLF) and extremely low frequency (ELF).
INFORMATION
Ce prodult est conforme aux normes du Swedish National Council
for Metrotogy de décembre 1990 (MPR Il) en ce qui concerne les
fréquences très basses (VLF) et extrêmement basses (ELF).
Hinweis
Dieses Gerät erfüllt bezüglich tieffrequenter (very low frequency)
und tiefstirequenter (extremely low frequency) Strahlung die
Vorschriften des ,Swedish National Council for Metrology (MPR)“
vom Dezember 1990 (MPR I{).
INFORMACION
Este producto cumple las normas del Consejo Nacional Sueco
para Metrologia (MPR) emitidas en diciembre de 1990 (MPR II
para frecuencias muy bajas (VLF) y frecuencias extremadamente
bajas (ELF).
Dieses Garät entspricht den folgenden europäischen EMV-
Vorschriften für Betrieb in Wohngebieten, gewerblicher Gebieten
und Leichtindustriegebieten.
EN55022/1994 Klasse B
EN50082-1/1992
EN61000-3-2/1995
2
As an ENERGY STAR Partner, Sony
Corporation has determined that this
нету product meets the ENERGY STAR
guidelines for energy efficiency.
- This monitor complies with the TCO
1992 guidelines for power saving
when used with a computer equipped
with VESA Display Power
Management Signaling (DPMS).
Declaration of Conformity
Trade Name: Sony
Model No.: CPD-110GS, CPD-210GS
Responsible Party: Sony Electronics inc.
Address: 1 Sony Drive, Park Ridge, NJ. 07656 USA
Telephone No.: 201-930-6970
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept
any interference received. including interference that may
cause undesired operation.
Table of Contents
Ce te ee ee ee ee 4
identifying parts and controls ............. 1 5
=1-111 AU 6
Step 1: Connect your monitor to your computer .............. 6
Step 2: Connect the power cord. ........... . ... 6
Step 3: Turn on the monitor and computer . ............ 6
Selecting the on-screen menu language
(LANGUAGE/INFORMATION) . ... и ныне 7
Customizing Your Monitor ........................ 8
Navigatingthemenu. ....................... .... ... ... 8
Adjusting the contrast and brightness
(CONTRAST/BRIGHTNESS) . .... o.oo ren, 9
Adjusting the horizontal size or centering of the picture
(H-SIZE/CENTER) ... oo LL a LL LL LL 10
Adjusting the vertical size or centering of the picture
(V-SIZE/CENTER) ...….....10220010a aa LL LL LL 10
Adjusting the curvature of the picture's sides
(PIN/PINBALANCE). ..... oo LL LL 10
Adjusting the angle of the picture's sides |
(КЕУ/КЕУ ВАСАМСЕ) ........... 2... ea nl 1
Adjusting the picture's rotation (ROTATION) ................. 11
Enlarging or reducing the picture (Z00M) ................—... 11
Adjusting the color of the picture (COLOR) .................. 11
Additional settings (DEGAUSS/CANCEL MOIRE)............. 12
Resetting the adjustments (RESET). ....................... 12
Technical Features ..........ñ...eeoóoceeccccdacoo 13
- o ara regsered trademark of Preset and user modes. .....................e.eeseeeeeo. 13
« Macintosh is a trademark licensed to Power saving function. ...................... .. . . . . 13
Apple Computer, Inc., registered in the
. wo arg end MS DOS ue registered Troubleshooting a... 20.000000. 000000000020 #8 13
trademarks of Microsoft Corporation in
the United States and other countries. If thin lines appear on your screen (damper wires). ............ 13
ВМ marks of IBM Corporation of he On-screen messages ....... EERE EEE 13
USA. Trouble symptoms and remedies... ........................ 14
* VESA and DDC" are trademarks of the Self-diagnosis function... ....... a 16
Video Electronics Standard
Association.
» ENERGY STAR is a US. registered Specifications. . .................. i... 16
mark.
* All other product names mentioned
herein may be the trademarks or Appendix..........0000000 esse a a aan en a sea aa aan ane |
registered trademarks of their respective
Fores. 0” ind “O” are no Preset mode timing table ..................................
mentioned in each case in this manual.
Precautions
Warning on power connections
* Use the supplied power cord. If you use a different power cord.
be sure that it is compatible with your local power supply.
For the customers in the U.S.A.
If you do not use the appropriate card. this monitor will not
conform to mandatory FCC standards.
Exampie of plug types
CE
for 100 to 120 V AC for 200 to 240 V AC
Before disconnecting the power cord. wait at least 30 seconds
after turning off the power to allow the static electricity on the
screen s surface to discharge.
After the power Is turned on. the screen 1s demagnetized
(degaussed) for about 5 seconds. This generates a strong
magnetic field around the screen which may affect data stored
on magnetic tapes and disks placed near the monitor. Be sure to
keep magnetic recording equipment, tapes. and disks away
from the monitor.
The equipment should be installed near an easily accessible
outlet.
installation
Do not instal! the monitor in the following places:
c a surfaces {.gs. blankets, etc.) or near matcnals (curtains,
draperies, etc.) that may block the ventilation holes
near heat sources such as radiators or air ducts, or in a place
subject to direct sunlight |
in a place subject to severe temperature changes
in a place subject to mechanical vibration or shock
on an unstable surface
near equipment which generates magnetism. such as a
transformer or high voitage power lines
near or on an electrically charged metal surface
Maintenance
Clean the screen with a soft cloth. If you use a glass cleaning
liquid, do not use any type of cleaner containing an anti-static
solution or similar additive as this may scratch the screen's
coating.
Do not rub. touch. or tap the surtace of the screen with sharp or
abrasive items such as a ballpoint pen or screwdriver. This type
of contact may result in a scratched picture tube.
Clean the cabinet. panel and controls with a soft cloth lightly
moistened with a mild detergent solution. Do not use any type
of abrasive pad. scouring powder or solvent, such as alcohol or
benzene.
Transportation
When you transport this monitor for repair or shipment, use the
original carton and packing materials.
Use of the tilt-swivel
This monitor can be adjusted within the angles shown below. To
tum the monitor verticaily or honzontaliv, hold it at the bottom
with both hands.
Identifying parts and controls
See the pages in parentheses for further details.
Front
MENU button (page 9)
This button displays the MENU OSD.
ENTER button (page 9)
This button selects the menu and adjustment items.
[3] O (contrast) +- buttons (page 9)
These buttons display the CONTRAST/BRIGHTNESS menu
and function as the +/— buttons when adjusting other items.
[4] () (nnwer) switch and indicator (pages 6, 13, 16)
This button tums the monitor on and off. The power indicator
lights up in green when the monitor is turned on, and either
flashes in green and orange. or lights up in orange when the
monitor 1s in power saving mode.
Rear
осо 98 ВРЯВНВНО В 686
AC IN connector (page 6)
This connector provides AC power to the monitor.
[6] Video input connector (HD15) (page 6)
This connector inputs RGB video signals (0.700 Vp-p, US
positive) and sync signals.
DOO9©
©OD08
НОВО
Pin No. Signal
ГЕ Red
Green
Blue
ID (Ground)
DDC Ground*
Red Ground
Green Ground
Blue Ground
bb
1 60 | —3 | Ea tal All
10 Ground
В ID (Ground)
12 Bi-Directional Data (SDA)*
13 H. Sync
14 V. Sync
15 Data Clock (SCL)*
* DDC (Display Data Channel) is a standard of VESA.
Setup Step 2: Connect the power cord
With the monitor and computer switched off, first connect the
Before using your monitor. check that the following accessories power cord to the monitor. then connect it to a power outlet.
are included in your carton:
* Power cord (1)
* Windows Monitor Information Disk (1)
* Warranty card (1) Ш
* Notes on cieaning the screen's surface (|)
* This instruction manual (1)
S66BRUEQANBE BE
Step 1:Connect your monitor to
your computer power cord (supplied) E to AC IN
—
Turn off the monitor and computer before connecting.
to a power outlet
B Connecting to an IBM PC/AT or compatible
computer
\
/
/
Step 3: Turn on the monitor and
computer
First tum on the monitor, then turn on the computer.
to video output The installation of your monitor is complete. |
If necessary, use the monitor's controls to adjust the picture.
IBM PC/AT or
compatible computer
-H Connecting to a Macintosh or compatible
computer
You will need a Macintosh adapter (not supplied).
3 сен р
A
Macintosh adapter
(not supplied)
— TEE)
Q £ € a
Macintosh or to video
compatible computer output
If no picture appears on your screen
* Check that the monitor is correctly connected to the computer.
* IF NO INPUT SIGNAL appears on the screen. contirm that
your computer's graphic board 15 completely seated in the
correct bus slot.
* If you are replacing an old monitor with this model and OUT
OF SCAN RANGE appears on the screen, reconnect the old
monitor. Then adjust the computer's graphic board so that the
horizontal frequency is between 30 — 70 kHz. and the vertical
frequency is between 48 — 120 Hz.
For more information about the on-screen messages. see “Trouble
symptoms and remedies’ on page 14.
For customers using Windows 95/98
To maximize the potential of your monitor. install the new model
information file from the supplied Windows Monitor Information Disk
onto your PC.
This monitor complies with the “VESA DDC” Plug & Play standard. If
your PC/graphics board complies with DDC. select "Plug & Play Monitor
(VESA DDC)" or this monitor's model name as the monitor type in the
“Control Panel” of Windows 95/98. If your PC/graphics board has
difficulty communicaung with this monitor, load the Windows Monitor
Information Disk and select this monitor's model name as the monitor
type.
For customers using Windows NT4.0
Monitor setup in Windows NT4.0 is different from Windows 95/98 and
does not involve the seiection of monitor type. Refer to the Windows
NT4.0 instruction manual for further details on adjusting the resolution,
refresh rate, and number of colors.
Adjusting the monitor's resolution and color number
Adjust the monitor's resolution and color number by referring to your
computer s instruction manual. The color number may vary according to
your computer or video board. The color palette setting and the actual
number of colors are as follows:
* High Color (16 bit) — 65.536 colors
* True Color (24 bit) — about 16.77 million colors
in true color mode (24 bit), speed may be slower.
Selecting the on-screen menu
language (LANGUAGE/
INFORMATION)
English. French. German, Spanish, and italian versions of the on-
screen menus are available. The default setting is English.
1 Press the MENU button.
See page 9 for more information on using the MENU button.
Ех 1 Т-+ #33
CAKEY /KEY BALANCE
OROTAT | ON
ES ZOOM
E COLOR
+e RESET
@ LANGUAGE / I NFORMAT | ON
t} DEGAUSS / CANCEL MOIRE
) IIPIN/PIN BALANCE
2 Press the +/- buttons to highlight § LANGUAGE/
INFORMATION and press the ENTER button.
See page 9 for more information on using the +/— and ENTER
buttons.
LANGUAGE / INFORMATION
EE Li
SENGL | SH «FRANCAIS
«DEUTSCH =| TAL {ANO
«ESPANOL
3 Press the ENTER button to select E (LANGUAGE)
and press +/— buttons to select a language.
* ENGLISH
* FRANCAIS: French
+ DEUTSCH: German
ESPANOL: Spanish
* ITALIANO: Italian
To close the menu
Press the MENU button once to retum to the main menu, and twice to
return to normal viewing. If no buttons are pressed, the menu closes
automatically after about 30 seconds.
To reset to English
See “Resetting the adjustments (RESET)” on page 12.
Customizing Your Monitor
You can make numerous adjustments {0 your monitor using the
on-screen menu.
Navigating the menu -
Press the MENU button to display the main MENU on your
screen. See page 9 for more information on using the MENU
button.
/ |
V-SIZE/CENTER
CIPIN/PIN BALANCE
CAKEY /KEY BALANCE
OROTATI
E ZOOM
COL
SET
B LANGUAGE / I NFORMAT ION
Use the +/— and ENTER buttons to select one of the following
menus. See page 9 for more information on using the +/— and
ENTER buttons.
[1] CONTRAST/BRIGHTNESS
Re NA: RCN
(page 9) CONTRAST |
Select the CONTRAST/ |
BRIGHTNESS menu to adjust
. , 60.0kHz/70.0Hz
the picture's contrast and 1024X768
brightness. нах
[2] H-SIZE/CENTER (page 10)
Select the H-SIZE/CENTER
menu to adjust the picture's
horizontal size and centering.
V-SIZE/CENTER (page 10)
Select the V-SIZE/CENTER
menu to adjust the picture's
vertical size and centering.
[4] PIN/PIN BALANCE (page 10)
Select the PIN/PIN BALANCE
menu to adjust the curvature
picture’s sides.
В 26 E |
SELECT+EIR EXIT-+7EN |
KEY/KEY BALANCE
(page 10)
TA — A
2 a |
SELECT+EW _EX!T.(EM |
Select the KEY/KEY BALANCE
menu to adjust the angle ot the
picture's sides.
[6] ROTATION (page 11) ra
Select the ROTATION menu to ROTA? LON |
adjust the picture 's rotation. O "a co
‘
SELECT+6 EXIT.» |
u
EY
26
KEY/KEY BALANCE
[7] ZOOM (page 11)
Select the ZOOM menu to enlarge
or reduce the picture.
8 COLIN page 11)
Select the COLOR menu to adjust
the picture s color temperature.
You can use this to match the
monitor's colors to a printed
picture s colors.
[9] RESET (page 12)
ET
Select the RESET menu to reset RESET
the adjustments.
. MODE ALL E
! EXIT»
LANGUAGE/INFORMATION
(page 7, 15)
Select the LANGUAGE/
INFORMATION menu to choose
the on-screen menu s language
and display this monitor's
information box.
LANGUAGE / INFORMATION
NA:
SENGLISH “FRANCAIS
“DEUTSCH «ITALIANO
“ESPANOL
| SELECT-+8N EXTEN
DEGAUSS/CANCEL MOIRE
(page 12)
Select the DEGAUSS/CANCEL
MOIRE menu to degauss the
screen and cancel the moire.
DEGAUSS/CANCEL MOIRE
DEGAUSS
EH Displaying the current input signal
The horizontal and vertical frequencies of the current input signal
are displayed in the CONTRAST/BRIGHTNESS menu. If the
signal matches one of this monitor’s factory preset modes. the
resolution 15 also displayed.
CONTRAST /BRIGHTNESS
E ++
CONTRAST
8 26
kHz / the horizontal
the resolution —— 1024X7 and vertical
of the current SELECT frequencies of
input signal the current
input signal
Using the MENU, ENTER, and +/- buttons
Select the menu you want to adjust.
Press the +/— buttons to highlight the desired menu. Press the
ENTER button to select the menu and adjustment stems.
Adjust the menu.
Press the +/— buttons to make the adjustment.
Close the menu.
Press the MENU button once to return to the main menu, and
twice to return to normal viewing. If no buttons are pressed.
the menu closes automatically after about 30 seconds.
Resetting the adjustments
You can reset the adjustments using the RESET menu. See
page 12 for more information on resetting the adjustments.
Adjusting the contrast and
brightness (CONTRAST/
BRIGHTNESS)
These settings are stored in memory for all input signals.
1
Press either one of the @ (CONTRAST) +/- buttons.
The CONTRAST/BRIGHTNESS menu appears on the
screen.
CONTRAST/BRIGHTNESS
o
A
CONTRAST
uu
BE 26
60 .0kHz/70.0Hz
1024X768
Press the ENTER button to select ® (CONTRAST) or
+ (BRIGHTNESS).
Press the +/— buttons to adjust either the contrast
(О) or brightness (+).
The menu automatically disappears atter about 30 seconds.
Adjusting the horizontal size or
centering of the picture (H-SIZE/
CENTER)
These settings are stored in memory for the current input signal.
1 Press the MENU button. |
The main MENU appears on the screen.
2 Press the +- buttons to highlight (= H-SIZE/
CENTER, and press the ENTER button.
The H-SIZE/CENTER menu appears on the screen.
3 First press the ENTER button to select the desired
adjustment item. Then press the +/— buttons to make
the adjustment.
Select To
adjust the horizontal size
=~ H-SIZE
(Th H-CENTER adjust the horizontal centering
Adjusting the vertical size or
centering of the picture (V-SIZE/
CENTER)
These settings are stored in memory for the current input signal.
1 Press the MENU button.
The main MENU appears on the screen.
2 Press the +/— buttons to highlight (3) V-SIZE/
CENTER, and press the ENTER button.
The V-SIZE/CENTER menu appears on the screen.
3 First press the ENTER button to select the desired
adjustment item. Then press the + buttons to make
the adjustment.
Select To
(3) V-SIZE adjust the vertical size
G V-CENTER adjust the vertical centering
10
Adjusting the curvature of the
picture’s sides (PIN/PIN BALANCE)
These settings are stored in memory fo: = current input signal.
1 Press the MENU button.
The main MENU appears on the sc- п.
2 Press the +/- buttons to high:. at 1% PIN/PIN
BALANCE, and press the EM" ZR button.
The PIN/PIN BALANCE menu pears on the screen.
3 First press the ENTER bi: 1 to select the desired
adjustment item. Then pre :5s the +/— buttons to make
the adjustment.
Select TO
) { PIN expand or contract the picture sides
D) PIN BALANCE
shift the picture sides to the left or night
Adjusting the angle of the picture's
sides (KEY/KEY BALANCE)
These settings are stored in memory for the current input signal.
1 Press the MENU button.
The main MENU appears on the screen.
2 Press the +- buttons to highlight 7 KEY/KEY
BALANCE, and press the ENTER button.
The KEY/KEY BALANCE menu appears on the screen.
3 First press the ENTER button to select the desired
adjustment item. Then press the +/— buttons to make
the adjustment.
Select To
adjust the picture width at the top of
the screen
CO KEY
TA KEY BALANCE shift the picture to the left or right at
the top of the screen
Adjusting the picture’s rotation
(ROTATION)
This setting is stored in memory for ail input signais.
1
Press the MENU button.
The main MENU appears on the screen.
Press the +/— buttons to highlight C3 ROTATION,
and press the ENTER button.
The ROTATION menu appears on the screen.
Press the +/— buttons to rotate the picture.
Enlarging or reducing the picture
(ZOOM)
This setting is stored in memory for the current input signal.
1 Press the MENU button.
The main MENU appears on the screen.
2 Press the +-— buttons to highlight €) ZOOM and
press the ENTER button.
The ZOOM menu appears on the screen.
3 Press the +4- buttons to enlarge or reduce the
picture.
Note
Adjustmezt “tops when =‘ther the horizontal or vertical size reaches its
maximum or minimum value:
Adjusting the color of the picture
(COLOR)
The COLOR settings ailow you to adjust the picture’s color
temperature by changing the color level of the white color field.
Colors appear reddish if the temperature is low, and bluish if the
temperature is high. This adjustment is useful for matching the
monitor's colors to a printed picture's colors.
This setting is stored in memory for all input signais.
1
Press the MENU button.
The main MENU appears on the screen.
Press the +/— buttons to highlight .*) COLOR and
press the ENTER button.
The COLOR menu appears on the screen.
Press the +/— buttons to select a coior temperature.
The preset color temperatures are S000K. 6500K. and 9300K.
Since the default setting is 9300K. the whites will change
from a bluish hue to a reddish hue as the temperature is
lowered to 6500K and S000K.
If necessary, fine tune the color temperature.
First press the +/— buttons to select USER. Then press the
ENTER button to select R (red), G (green), or B (blue) and
. press the +/— buttons to make the adjustment.
If you fine tune the color temperature, the new color settings
are stored in memory and recalled whenever you select
USER.
11
Additional settings (DEGAUSS/
CANCEL MOIRE)
You can manually degauss (demagnetize) the screen. and cancel
the moire. |
1 Press the MENU button. "
The main MENU appears on the screen.
2 Press the +/— buttons to highlight t+ DEGAUSS/
CANCEL MOIRE and press the ENTER button.
The DEGAUSS/CANCEL MOIRE menu appears on the
screen.
3 Press the ENTER button to select the desired
adjustment item.
Adjust the selected item according to the following
instructions.
Degaussing the screen
The monitor is automatically demagnetized when the power is
turned on.
To manuaily degauss the monitor, first press the
ENTER button to select > (DEGAUSS). Then press the
+ button.
The screen is degaussed for about 5 seconds. If a second degauss
cycle is needed, allow a minimum interval of 20 minutes for the
best result.
Cancelling the moire
If elliptical or wavy patterns appear on the screen. adjust the
moire cancellatiGa sevel. |
To adjust the amount of moire cancellation, first press
the ENTER button to select (1) (CANCEL MOIRE). Then
press the +/- buttons until the moire effect is at a
minimum.
". Moire is a type of natural interference which produces soft. wavy ines
on your screen. it may appear due to interference between the pattern
of the picture on the screen and the phosphor pitch pattern of the
monitor.
Example of moire
12
Resetting the adjustments (RESET)
This monitor has the following two reset methods. Use the
RESET menu to reset the adjustments.
1 Press the MENU button.
The main MENU appears on the screen.
2 Press the +- buttons to highlight +-+- RESET and
press the ENTER button.
The RESET menu appears on the screen.
Reset the settings accordine to the following instructions.
Resetting all of the adjustment data for the
current input signal (MODE)
Press the — button.
The MODE item is selected. All of the adjustment data for the
current input signal is reset.
Note that the following items are not reset by this method:
* on-screen menu language (page 7)
* picture s rotation (page 11)
Resetting ail of the adjustment data to factory
preset leveis (ALL)
Press the + button.
The ALL item is selected. With the exception of the USER
settings in the COLOR menu, all of the adjustment data for all
input signals is reset to the factory preset levels.
Note
The monitor's buttons will not operate for about 5 seconds when ALL is
selected.
Trouble symptoms and remedies
If the problem is caused by the connected computer or other equipment, please reter to the connected equipment's instruction manual.
Use the self-diagnosis function (page 16) if the following recommendations do not resolve the problem.
Symptom Check these items
No picture »
If the O (power) indicator is not lit * Check that the power cord 1s properly connected.
+ Check that the (À (power) switch is in the “on” position.
[f the NO INPUT SIGNAL message + Check that the video signal cable is properly connected and all plugs are firmly seated in
appears on the screen. or if the () their sockets (page 6).
(power) indicator 1s either orange or * Check that the HD15 video input connector's pins are not bent or pushed in.
i d
alternating between green an M Problems caused by the connected computer or other equipment
orange * The computer is in power saving mode. Try pressing any key on the computer keyboard.
* Check that the computers power 15 “on.”
+ Check that the graphic board is completely seated in the proper bus slot.
If the OUT OF SCAN RANGE MProblems caused by the connected computer or other equipment
message appears on the screen * Check that the video frequency range 1s within that specified tor the monitor. If you
replaced an old monitor with this monitor. reconnect the old monitor and adjust the
frequency range to the following.
Horizontal: 30-70 kHz
Vertical: 48-120 Hz
If no message is displayed and the + Usethe Self-diagnosis function (page 16).
(power) indicator 1s green or flashing
orange
If using Windows 95/98 * if you replaced an old monitor with this monitor, reconnect the old monitor and do the
following. Install the Windows Monitor information Disk (page 7) and select this monitor
CCPD-110GS” or “CPD-210GS”) from among the Sony monitors in the Windows 95/98
monitor selection screen. |
"I using a Mcintosh system » Clack that the Macintosh adapter (not supplied) and the video signal cable are properly
- - connected (page 6).
Picture flickers, bounces, + Isolate and eliminate any potential sources of electric or magnetic fields such as other
oscillates, or is scrambled monitors. laser printers, electric fans. fluorescent lighting, or televisions.
* Move the monitor away from power lines or place a magnetic shield near the monitor.
* Try plugging the monitor into a different AC outlet, preferably on a different circuit.
* Try turning the monitor 90° to the left or right.
EProblems caused by the connected computer or other equipment
* Check your graphics board manual for the proper monitor setting.
* Confirm that the graphics mode (VESA, Macintosh 16" Color. etc.) and the frequency of
the input signal are supported by this monitor (Appendix). Even if the frequency is within
the proper range, some video boards may have a sync pulse that is too narrow for the
monitor to sync correctly. |
* Adjust the computer's refresh rate (vertical frequency) to obtain the best possible picture.
Picture is fuzzy * Adjust the contrast and brightness (page 9).
* Degauss the monitor* (page 12).
* Decrease the moire cancellation effect (page 12).
14
ED
Technical Features
Preset and user modes
When the monitor receives an input signal, is automatically
matches the signal to one of the factory preset modes stored in the
monitor's memory to provide a high quality picture at the center
of the screen. (See Appendix for a list of the factory preset
modes.) For input signals that do not match one of the factory
preset modes. the digital Multiscan technology of this monitor
ensures that a clear picture appears on the screen tor any timing in
the monitors frequency range (horizontal: 30 — 70 kHz. vertical:
48 — 120 Hz) . If the picture is adjusted. the adjustment data is
stored as a user mode and automaticaily recalled whenever the
same tnput signal is received.
Note for Windows users
For Windows users, check your video board manual or the utility
program which comes with your graphic board and select the
highest available refresh rate to maximize monitor performance.
Power saving function
This monitor meets the power-saving guidelines set by VESA.
ENERGY STAR. and NUTEK. If the monitor is connected to a
computer or video graphics board that is DPMS ( Display Power
Management Signaling) compliant, the monitor will
automaticaily reduce power consumption in three stages as shown
below.
Power mode Power (power) indicator
consumption
normal < 110 W green
operation (CPD-210GS)
< 105 W
(CPD-110GS)
| standby <15W green and orange
alternate
2 suspend <15W green and orange
alternate
3 active off* <5W orange
power off 0 W off
* When your computer enters the “active off" mode, the input signal is
cut and NO INPUT SIGNAL appears on the screen. After 20 seconds,
the monitor enters the power saving mode.
Troubleshooting
Before contacting technical support. refer to this section.
If thin lines appear on your screen
(damper wires)
The lines you are experiencing on your screen ar ormal for the
Trinitron monitor and are not a malfunction. T° ¢ are shadows
from the damper wires used to stabilize the apc - :re grille and are
most noticeable when the screen's backgrour:. .s light (usually
white). The aperture grille is the essential element that makes a
Trinitron picture tube unique by allowing more light to reach the
screen, resulting in a brighter. more detailed picture.
Damper wires
On-screen messages
If there is something wrong with the input signal, one of the
following messages appears on the screen. To solve the problem,
see “Trouble symptoms and remedies” on page 14.
QINFORMATION
i
[OUT OF SCAN RANGE} Input signal condition
The input signal condition
OUT OF SCAN RANGE
indicates that the input signal is not supported by the
monitor's specifications.
NO INPUT SIGNAL
indicates that no signal is being input to the monitor.
13
Self-diagnosis function
This monitor is equipped with a self-diagnosis function. if there is
a problem with your monitor or computer. the screen will go
blank and the ©) (power) indicator will either light up green or
flash orange. If the ) (power) indicator is lit in orange, the
computer is 1n power saving mode. Try pressing any key on the
keyboard.
L _
|
T TE)
Lo J
y (power) indicator
If the O (power) indicator is green
1 Disconnect the video input cable, or turn off the
connected computer.
2 Press the ©) (power) button to turn the monitor off
and on.
3 Press and hold the + button for 2 seconds before the
monitor enters power saving mode.
If all three color bars appear (red. green. blue). the monitor is
working properly. Reconnect the video input cables and check the
condition of your computer.
[f the color bars do not appear. there 15 a potential monitor failure.
“Inform your authorized Sony dealer of the monitor's condition.
If the () (power) indicator is flashing orange
Press the () (power) button to turn the monitor off and
on.
If the © (power) indicator lights up green, the monitor is working
properly.
If the () (power) indicator is still flashing. there is a potential
monitor failure. Count the number of seconds between orange
flashes of the O (power) indicator and inform your authorized
Sony dealer of the monitor's condition. Be sure to note the model
name and serial number of vour monitor. Also note the make and
model of your computer and video board.
1A
Specifications
CPD-110GS
CRT 0.25 mm aperture grille pitch
15 inches measured diagonaily
90-degree deflection
Viewable image size Approx. 285 x 214 mm (w/h)
(11 174 x 8 1/2 inches)
14.0" viewing image
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Approx. 270 x 202 mm (w/h}
(10/4 x 8 inches)
Horizontal: 30 to 70 kHz
Vertical: 48 to 120 Hz
AC input voltage/current 100 to 240 Y, 50-60 Hz, 1.6-0.8A
Power consumption Max. 105 W
Resolution
Standard image area
Deflection frequency *
Dimensions Approx. 368 x 393 x 389 mm (w/h/d)
(14 112 x 15 172 x 15 3/8 inches)
Mass Approx. 14 kg (30 1b 14 oz)
Plug and Play DDC1/DDC2B
Supplied accessories See page 6
* Recommended horizontal and vertical timing condition
* Horizontal sync width should be more than 1.0 psec.
* Honzontal blanking width should be more than 3.6 usec.
* Vertical blanking width should be more than 500 usec.
CPD-210GS
CRT 0.25 mm aperture grille pitch
17 inches measured diagonally
90-degree deflection
Viewable image size Approx. 327 x 243 mm (w/h)
(12 7/2 x 9 3/s inches)
16.0" viewing image
Horizontal: Max. 1280 dots
Vertical: Max. 1024 lines
Approx. 312 x 234 mm (w/h)
(12% x9 1/4 inches)
Horizontai: 30 to 70 kHz
Vertical: 48 to 120 Hz
AC input voltage/current — 100 to 240 У, 50 - 60 Нг. 1.7 - 0.9 А
Power consumption Max. 110 W
Resolution
Standard image area
Deflection frequency*
Dimensions Approx. 406 x 431.5 x 420 mm (w/h/d)
(16 x 17 x 16 °/8 inches)
Mass Approx. 18.5 kg (40 1b 13 oz)
Plug and Play DDC1/DDC2B
Supplied accessories See page 6
* Recommended horizontal and vertical timing condition
* Horizontal sync width should be more than 1.0 psec.
* Horizontal blanking width shouid be more than 3.0 psec.
* Vertical blanking width should be more than 500 psec.
Design and specifications are subject to change without notice.
Symptom
Picture is ghosting
Picture is not centered or sized
properly
Edges of the image are curved
Wavy or elliptical pattern (moire)
is visible
Check these items
+
2
a
Eliminate the use of video cable extensions and/or video switch boxes.
Check that ail plugs are firmly seated in their sockets.
Adjust the size or centering (page 10). Note that some video modes do not fill the screen
to the edges.
Adjust the shape of the picture (page 10).
Cancel the moire (page 12).
M Problems caused by the connected computer or other equipment
Change your desktop pattern.
Color is not uniform
Degauss the monitor* (page 12). If you place equipment that generates a magnetic field.
such as a speaker. near the monitor, or if you change the direction the monitor faces. color
may lose uniformity.
White does not look white
Adjust the color temperature (page 11).
A hum is heard right after the
power is turned on
This is the sound of the auto-degauss cycle. When the power is tumed on. the monitor is
automatically degaussed Гог 5 seconds.
* If a second degauss cycle is needed, allow a minimum interval of 20 minutes for the best result. A humming noise may be heard. but this is not a
malfunction.
Displaying this monitor's name, serial number, If the problem persists. call your authorized Sony dealer and give
and date of manufacture (INFORMATION) the following information.
1 Press the MENU button.
The main MENU appears on the screen.
* Model name: CPD-110GS or CPD-210GS
* Serial number
* Name and specifications of your computer and graphics board.
2 Press the +/- buttons to highlight § LANGUAGE/
INFORMATION and press the ENTER button.
The LANGUAGE/INFORMATION menu appears on the
screen.
3 Press the ENTER button to select ©
(INFORMATION).
This monitor's information box appears on the screen.
Example LANGUAGE / INFORMATION
a o
MODEL :CPD-110GS
SERIAL:12345678
MANUFACTURED: 1998
SELECT»SE EXIT.
ыы
18
Appendix
Preset mode timing table
No. Resolution Horizontal Vertical Graphics
(dots x lines) Frequency Frequency Mode
1 640 x 480 31.5 kHz 60 Hz VGA-G
2 640 x 480 43.3 kHz 85 Hz VESA
3 720x400 31.5 kHz 70 Hz VGA-Text
4 800x600 46.9 kHz 75 Hz VESA
5 800 >x 600 53.7 kHz 85 Hz VESA
6 832x624 49.7 kHz 75 Hz Macintosh 16”
Color
7 1024x 768 60.0 kHz 75 Hz VESA
8 1024 x 768 68.7 kHz 85 Hz VESA
9 1280x1024 64.0 kHz 60 Hz VESA
Sony (gine http:/Avww.worid.sony.com/
Sony Corporation Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement