Sony | KV-21FX30E | User's Manual | Sony KV-21FX30E User's Manual

SERVICE MANUAL
MODEL
KV-21FX30B
KV-21FX30E
COMMANDER
DEST
CHASSIS NO.
RM-887
FR
SCC-Q54G-A
RM-887
ESP
SCC-Q53H-A
FE-2 CHASSIS
MODEL
KV-21FX30K
COMMANDER
RM-887
DEST
OIRT
CHASSIS NO.
SCC-Q51J-A
RM-889
1
TABLE OF CONTENTS
Section
Title
Page
Section
Title
Specifications
Connectors
Self Diagnostic Software
....................
....................
....................
3
4
5
4. CIRCUIT ADJUSTMENTS
Switching On the TV and
Automatically Tuning
Introducing the Menu System
Menu Guide
Teletext
Specifications
Troubleshooting
....................
....................
....................
....................
....................
....................
6
7
7
10
11
11
5. DIAGRAMS
4-1.
4-2.
4-3.
1. GENERAL
5-1.
5-2.
5-3.
2. DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
2-8.
2-9.
Page
Rear Cover Removal
Speaker Disconnection
Speaker Box Removal
Speaker Box Disassembly
A Board PWB Removal 1
A Board PWB Removal 2
Service Position
Wire Dressing
Picture Tube Removal
....................
....................
....................
....................
....................
....................
....................
....................
....................
12
12
12
12
13
13
13
13
14
....................
....................
....................
....................
15
16
18
18
5-4.
5-5.
Electrical Adjustments
Test Mode 1
Test Mode 2
Block Diagrams (1)
Block Diagrams (2)
Circuit Board Location
Schematic Diagrams and
Printed Wiring Boards
* C Board
* A Board
Semiconductors
IC Blocks
....................
....................
....................
19
21
21
....................
....................
....................
23
25
26
....................
....................
....................
....................
....................
26
27
29
37
39
....................
....................
40
41
....................
42
6. EXPLODED VIEWS
6-1.
6-2.
Chassis
Picture Tube
7. ELECTRICAL PARTS LIST
3. SET-UP ADJUSTMENTS
3-1.
3-2.
3-3.
3-4.
Beam Landing
Convergence
Focus Adjustment
Screen (G2), White Balance
CAUTION
ATTENTION
SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND THE
ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE
CARBON PAINTED ON THE CRT, AFTER REMOVAL OF THE
ANODE CAP.
APRES AVOIR DECONNECTE LE CAP DE’LANODE,
COURT-CIRCUITER L’ANODE DU TUBE CATHODIQUE ET
CELUI DE L’ANODE DU CAP AU CHASSIS METALLIQUE DE
L’APPAREIL, OU AU COUCHE DE CARBONE PEINTE SUR LE
TUBE CATHODIQUE OU AU BLINDAGE DU TUBE
CATHODIQUE.
WARNING !!
ATTENTION !!
AN ISOLATION TRANSFORMER SHOULD BE USED DURING
ANY SERVICE WORK TO AVOID POSSIBLE SHOCK HAZARD
DUE TO LIVE CHASSIS, THE CHASSIS OF THIS RECEIVER IS
DIRECTLY CONNECTED TO THE POWER LINE.
AFIN D’EVITER TOUT RISQUE D’ELECTROCUTION
PROVENANT D’UN CHÁSSIS SOUS TENTION, UN
TRANSFORMATEUR D’ISOLEMENT DOIT ETRE UTILISÈ LORS
DE TOUT DÈPANNAGE LE CHÁSSIS DE CE RÈCEPTEUR EST
DIRECTMENT RACCORDÈ Á L’ALIMENTATION SECTEUR.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY SHADING AND MARKED £ ON
THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
PARTS LIST ARE CRITICAL FOR SAFE OPERATION. REPLACE
THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AUX COMPOSANTS RELATIFS Á
LA SECURITÈ!!
LES COMPOSANTS IDENTIFIÈS PAR UNE TRAME ET PAR UNE
MARQUE £ SUR LES SCHÈMAS DE PRINCIPE, LES VUES
EXPLOSÈES ET LES LISTES DE PIECES SONT D’UNE IMPORTANCE CRITIQUE POUR LA SÈCURITÈ DU FONCTIONNEMENT,
NE LES REMPLACER QUE PAR DES COMPSANTS SONY DONT
LE NUMÈRO DE PIÈCE EST INDIQUÈ DANS LE PRÈSENT
MANUEL OU DANS DES SUPPLÈMENTS PUBLIÈS PAR SONY.
2
ITEM MODEL
Television System
Stereo System
B
B/G/H, D/K, I, L
GERMAN/NICAM
Stereo
E
B/G/H, D/K
GERMAN/NICAM
Stereo
K
B/G/H, D/K
GERMAN/NICAM
Stereo
Flat Display FD Trinitron
Approx 55 cm (21 inches)
(Approx 51 cm picture measured
diagonally)
Picture Tube
Input/Output Terminals [REAR]
Inputs for Audio and Video signals.
1: 21-pin Euro connector Inputs for RGB.
(CENELEC standard)
Outputs of TV Video and Audio
signals.
Inputs for Audio and Video signals.
2: 21-pin Euro connector Inputs for S Video.
Outputs of TV Video and Audio signals.
(selectable)
RCA Connectors
Variable Output for audio signals
Input/Output Terminals [FRONT]
Headphone jack
stereo mini jack
Audio inputs
phono jacks
Video inputs
phono jacks
Channel Coverage
VHF : E2-E12, F2-F10
UHF : E21-E69, F21-F69, B21-B69
CABLE TV : S01-S03, S1-S20, B-Q
HYPER : S21-S41
VHF : E2-E12
UHF : E21-E69
CABLE TV : S01-S03, S1-S20
HYPER : S21-S41
VHF : E2-E12, R01-R12
UHF : E21-E69, R21-R69
CABLE TV : S01-S03, S1-S20
HYPER : S21-S41
Sound output
Right and Left speaker
Color System
PAL, SECAM
NTSC4.43, NTSC3.58
(VIDEO IN)
PAL, SECAM
NTSC4.43, NTSC3.58
(VIDEO IN)
PAL, SECAM
NTSC4.43, NTSC3.58
(VIDEO IN)
2x14W (Music Power)
General Specifications
Power Requirements
220 - 240V
Power Consumption
87 W
Dimensions
Approx 545x446x485 mm
Weight
Approx 26kg
RM-887 Remote Commander (1)
IEC designated R6 battery (2)
TV system Autodetection, Teletext
Other Features
Smar tlink
Remote Control System : Infrared Control
3V dc
Power requirements
2 batteries IEC designation
R6 (size AA)
Supplied Accessories
Design and specifications are subject to change without notice.
Model Name
KV-21FX30B
KV-21FX30E
KV-21FX30K
Pal Comb
OFF
OFF
OFF
PIP
OFF
OFF
OFF
RGB Priority
ON
ON
ON
Woofer Box
OFF
OFF
OFF
Scar t 1
ON
ON
ON
Item
2x7W (RMS)
Scar t 2
ON
ON
ON
Front in (3)
ON
ON
ON
Scar t 4
OFF
OFF
OFF
Projector
OFF
OFF
OFF
Norm B/G
ON
ON
ON
Norm I
ON
OFF
OFF
Norm D/K
ON
ON
ON
Norm AUS
OFF
OFF
OFF
Norm L
ON
OFF
OFF
Norm SAT
OFF
OFF
OFF
Norm M
OFF
OFF
OFF
Teletext
ON
ON
ON
Nicam Stereo
ON
ON
ON
3
21 pin connector
Pin No
1
2
4
1
Signal
Signal level
Audio output B
(right)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
2
Audio output B
(right)
Standard level : 0.5V rms
Output impedence : More than 10kohm*
3
Audio output A
(left)
Standard level : 0.5V rms
Output impedence : Less than 1kohm*
4
Ground (audio)
5
Ground (blue)
20
6
Audio input A
(left)
18
7
Blue input
0.7 +/- 3dB, 75 ohms positive
8
Function select
(AV control)
High state (9.5-12V) : Part mode
Low state (0-2V) : TV mode
Input impedence : More than 10K ohms
Input capacitance : Less than 2nF
9
Ground (green)
10
Open
11
Green
12
Open
13
Ground (red)
21
19
Standard level : 0.5V rms
Output impedence : More than 10kohm*
17
16
15
14
13
12
11
10
9
8
7
6
5
14
Ground (blanking)
_
4
3
Red input
0.7 +/- 3dB, 75 ohms, positive
(S signal Chroma
input)
0.3 +/- 3dB, 75 ohms, positive
16
Blanking input
(Ys signal)
High state (1-3V) Low state (0-0.4V)
Input impedence : 75 ohms
17
Ground (video
output)
18
Ground (video
input)
19
Video output
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
Video input
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
Video input
Y (S signal)
1V +/- 3dB, 75ohms, positive sync 0.3V
(-3+10dB)
15
_
_
2
1
Green signal : 0.7 +/- 3dB, 75 ohms,
positive
_
20
_
_
21
Common ground
(plug, shield)
Connected
Rear Connection Panel
Not Connected (open)
Front Connection Panel
4
* at 20Hz - 20kHz
FE-2 SELF DIAGNOSTIC SOFTWARE
The identification of errors within the FE-2 chassis is triggered in one of two ways :- 1: Busy or 2: Device failure to respond to IIC. In the event
of one of these situations arising the software will first try to release the bus if busy (Failure to do so will report with a continuous flashing
LED) and then communicate with each device in turn to establish if a device is faulty. If a device is found to be faulty the relevant device number
will be displayed through the LED (Series of flashes which must be counted) See table 1., non fatal errors are reported using this method.
Each time the software detects an error it is stored within the NVM. See Table 2.
Table 1
How to enter into Table 2
Error Message
No error
Reser ved
OCP ( Over Current Protection )
Not Used
No Ver tical Sync
IKR Error at power on
IIC bus clock and/or data lines low at power on
NVM no IIC bus acknowledge at power on
Not Used
Tuner no acknowledge at power on
Sound Processor Error
Jungle controller 8 volts error
LED
Code
00
01
02
03
04
05
06
07
08
09
10
11
1.
2.
3.
Turn on the main power switch of the TV set and enter into
the‘Stanby Mode’.
Press the following sequence of buttons on the Remote
Commander.
i+
5
-
(ON SCREEN
DISPLAY)
(DIGIT 5)
(VOLUME -)
(TV)
The following table will be displayed indicating the error
count.
Flash Timing Example : e.g. error number 3
Table 2
StBy LED
ON
ON
OFF
ON
ERROR MENU
E02
E03
E04
E05
E06
E07
E08
E09
E10
E11
OFF
WORKING TIME
HOURS
MINUTES
OCP
OVP N/A
VSYNC
IKR
IIC
NVM
JUNGLE
TUNER
SOUNDP
8V
(0,
(0,
(0,
(0,
(0,
(0,
(0,
(0,
(0,
(0,
255)
255)
255)
255)
255)
255)
255)
255)
255)
255)
0
0
0
0
0
0
0
0
0
0
2
11
Note: To clear the error count data press ‘80’ on the Remote
commander.
5
6
If it is not necessary, press
necessary and press OK.
or
to select Not
or
to select Adjust now,
then press OK and correct any slant of the picture
between –5 and +5 by pressing
or
. Finally press
OK to store.
b) If it is necessary, press
a)
The Picture Rotation menu allows you to correct the
picture slants if it is necessary.
4 Because of the earth’s magnetism, the picture might slant.
• If the country in which you want to use the TV set
does not appear in the list, select “-” instead of a
country.
• In order to avoid wrong teletext characters for
Cyrillic languages we recommend to select Russia
country in the case that your own country does not
appear in the list.
screen. Press the
or
button to select the country in
which you will operate the TV set, then press the OK
button to confirm your selection.
3 The Country menu appears automatically on the TV
or
button on the remote control to select
the language, then press the OK button to confirm your
selection. From now on all the menus will appear in the
selected language.
2 Press the
50Hz)
Press the
on/off button on the TV set to turn on the TV.
The first time you press this button, a Language menu
displays automatically on the TV screen.
1 Connect the TV plug to the mains socket (220-240V AC,
OK
OK
OK
7
continued...
K
K
K
First Time Operation
Not necessary
Adjust now
If picture slants, please
adjust picture rotation
Select country:
Country
i4
Sverige
Norge
Italia
Deutschland
Österreich
i$
Select Language:
i4
Svenska
Norsk
English
Nederlands
Français
Italiano
i$
Language
The first time you switch on your TV, a sequence of menu screen appear on the TV enabling
you to: 1) choose the language of the menu screen, 2) choose the country in which you wish
to operate the TV, 3) adjust the picture slant 4) search and store all available channels (TV
Broadcast) and 5) change the order in which the channels (TV Broadcast) appear on the
screen.
However, if you need to change any of these settings, you can do that by selecting the
appropriate option in the
(Set Up menu) or by pressing the Auto Start Up Button
on the TV set.
Switching On the TV and Automatically Tuning
GB
b)
a)
3 Repeat steps b)1 and b)2 if you wish to change
the order of the other channels.
2 Press the
or
button to select the new
programme number position for your selected
channel (TV Broadcast), then press
.
1 Press the
or
button to select the programme
number with the channel (TV Broadcast) you wish
to rearrange, then press the
button.
If you wish to store the channels in a different order:
If you wish to keep the broadcast channels in the
tunned order, go to step 8.
After all available channels are captioned and stored,
the Programme Sorting menu appears automatically
on the screen enabling you to change the order in
which the channels appear on the screen.
8
First Time Operation
Your TV is now ready for use
screen.
8 Press the MENU button to remove the menu from the
7
If no channels were found during the auto tuning
process then a new menu appears automatically on
the screen asking you to connect the aerial. Please
connect the aerial (see page 6) and press OK. The
auto tuning process will start again.
This procedure could take some minutes. Please be
patient and do not press any button. Otherwise the
automatic tuning will not be completed.
available broadcast channels for you.
6 The TV starts to automatically search and store all
OK button to select Yes.
5 The Auto Tuning menu appears on the screen. Press the
The operating instructions mentioned here are partial abstracts from the ‘Operating
Instruction Manual’. The page numbers of the ‘Operating Instruction Manual’ remain
as in the manual.
01
B/G
C21
OK
05
Select new position:
Exit: MENU
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58
Programme Sorting
Select channel:
Exit: MENU
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58
Programme Sorting
Confirm
C27
OK
OK
OK
No channel found
Please connect aerial
Searching...
Programme:
System:
Channel:
Auto Tuning
Yes
No
Do you want to start
automatic tuning?
MENU
K
K
K
K
SECTION 1 GENERAL
7
.
.
/
or
/
.
OK
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Level 2
OK
.
MENU
K
MENU
Menu System
9
continued...
To do this: after selecting the item you want to
alter press
, then press repeatedly
/
/
or
to adjust it and finally press OK to
store the new adjustment.
This menu also allows you to customise the
picture mode based on the programme you are
watching:
Personal (for individual settings).
Live (for live broadcast programmes).
Movie (for films).
PICTURE ADJUSTMENT
The “Picture Adjustment” menu allows you to
alter the picture adjustments.
Level 3 / Function
or
• Brightness, Colour and Sharpness can only be alterated if “Personal” mode is selected.
• Hue is only available for NTSC colour signal (e.g: USA video tapes).
• Select Reset and press OK to reset the picture to the factory preset levels.
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Level 1
Menu Guide
3 Press the MENU button to remove the menu from the screen.
• To confirm and store your selection, press OK.
• To alter settings of your selected option, press
• To return to the last menu or option, press
• To enter to the selected menu or option, press
2 • To highlight the desired menu or option, press
1 Press the MENU button to switch the first level menu on.
Your TV uses an on-screen menu system to guide you through the operations. Use the
following buttons on the Remote Control to operate the menu system:
Introducing and Using the Menu System
GB
OK
OK
Sound Adjustment
Mode: Personal
Treble
Bass
Balance
Reset
Dual Sound: Mono
Detail Adjustment
Level 2
OK
To do this: after selecting the item you want to
alter, press
. then press repeatedly
/
/
or
to adjust it and finally press OK
to store the new adjustment.
SOUND ADJUSTMENT
The “Sound Adjustment” menu allows you to
alter the sound adjustments.
Level 3 / Function
TV Speakers:
Auto volume:
Sound Effect:
On:
Off:
On:
Off:
Sound from external amplifier
connected to the audio outputs on
the rear of the TV set.
Sound from the TV set.
Volume channel changes according
to the broadcast signal.
Volume level of the channels will
stay the same, independent of the
broadcast signal (e.g. in the case of
advertisements).
Off:
Normal.
Spatial: Acoustic sound effect.
Personal (for individual settings)
Rock
Pop
Jazz
10
Menu System
continued...
• In case of a bilingual broadcast select Dual Sound and set A for sound channel 1, B for sound channel
2 or Mono for mono channel if available. For a stereo broadcast you can choose Stereo or Mono.
• Select Reset and press OK to reset the sound to the factory preset levels.
• Treble and Bass can only be altered if “Personal” mode is selected.
Detail Adjustment
Mode
This menu also contains two submenus as following:
Sound Adjustment
Mode: Personal
Treble
Bass
Balance
Reset
Dual Sound: Mono
Detail Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Level 1
8
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Sleep Timer:
On Timer:
Timer
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
OK
OK
OK
Off
Off
OK
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Sleep Timer:
On Timer:
Timer
Timer
Sleep Timer:
On Timer:
Off
Off
Timer
OK
Level 2
Sleep Timer:
On Timer:
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Level 1
i
OK
OK
Off
Off
OK
Off
Off
Menu System
11
continued...
To do this: after selecting the option, press
and then proceed in the same way as in the
steps 2 and 3 of the section “Switching On the
TV and Automatically Tuning”.
LANGUAGE / COUNTRY
The “Language/Country” option in the “Set
Up” menu allows you to select the language
that the menus are displayed in. It also allows
you to select the country in which you wish to
operate the TV set.
If you have not activated the “On Timer”
option but the indicator
on the TV set
flashes, please contact to your nearest
Sony Service Centre.
• The standby indicator
on the TV set flashes
regularly to indicate that “On Timer” is active.
• Any loss of power will cause these settings to be
cleared.
To do this: after selecting the option press
,
then press
or
to set the time period delay
(max. 12 hours) and press OK to store. Finally
on the remote
press the standby button
control. After the selected length of time the TV
switches on automatically.
ON TIMER
The “On Timer” option in the “Timer” menu
allows you to select a time period for the TV to
switch itself automatically on from standby
mode.
• While watching the TV, you can press the
button on the remote control to display the
time remaining.
• One minute before the TV switches itself into
standby mode, the time remaining is displayed on
the TV screen automatically.
To do this: after selecting the option press ,
then press
or
to set the time period delay
(max. of 4 hours) and finally press OK to store.
SLEEP TIMER
The “Sleep Timer” option in the “Timer” menu
allows you to select a time period for the TV to
switch itself automatically into the standby
mode.
Level 3 / Function
GB
12
Menu System
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Level 1
OK
OK
OK
OK
OK
OK
OK
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Level 2
OK
OK
OK
OK
continued...
To do this:
1 After selecting the option, press
, then
press
or
to select the input source you
wish to name (AV1 and AV2 are for the rear
Scarts and AV3 for front connectors). Then
press .
AV PRESET
The “AV Preset” option in the “Set Up” menu
allows you to designate a name to the external
equipment you have connected to the sockets of
this TV.
To do this:
1 After selecting the option, press
, then
press
or
to select the programme
number with the channel you wish to name.
2 Press
. With the first element of the Label
column highlighted, press
or
to select
a letter or number (select “-“ for a blank), then
press
to confirm this character. Select the
other four characters in the same way. Finally
press OK to store.
PROGRAMME LABELS
The “Programme Labels” option in the “Set
Up” menu allows you to name a channel using
up to five characters (letters or numbers).
To do this: after selecting the option, press
and then proceed in the same way as in step 7 b)
of the section “Switching On the TV and
Automatically Tuning”.
PROGRAMME SORTING
The “Programme Sorting” option in the “Set
Up” menu allows you to change the order in
which the channels (TV Broadcast) appear on
the screen.
To do this: after selecting the option, press
and then proceed in the same way as in TV
steps 5 and 6 of the section “Switching On the
TV and Automatically Tuning”.
AUTO TUNING
The “Auto Tuning” option in the “Set Up”
menu allows you to automatically search for
and store all available TV channels.
Level 3 / Function
9
14
Menu System
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Level 1
OK
OK
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Level 2
OK
Level 3 / Function
continued...
To cancel this function afterwards, select “Off”
instead of “On” in the step above.
To do this: select the Decoder option and
press . Next press
or
to select On.
Finally press OK twice to confirm and store.
This option is only available depending
on the country you have selected in the
“Language/Country” menu.
correctly scrambling channels when using a
decoder connected to the Scart :2/ S
directly or through a VCR.
e) This option allows you to view and record
To cancel this function afterwards, select “No”
instead of “Yes” in the step above.
To do this: Highlighting the Programme
option, press the PROGR +/- button to select
the programme number you want to skip.
When the programme you want to skip
appears on the screen, select the Skip option
and press
. Next press
or
to select
Yes. Finally press OK twice to confirm and
store.
when they are selected with the PROGR +/buttons.
d) Skip any unwanted programme numbers
To do this: while watching the channel (TV
Broadcast) you wish to fine tune, select the
AFT option and press . Next press
or
to adjust the fine tuning between -15
and +15. Finally press OK twice to store.
operating, however you can manually fine
tune the TV to obtain a better picture
reception in the case that the picture is
distorted.
c) Normally the automatic fine tuning (AFT) is
To do this: Highlighting the Programme
option, press the PROGR +/- button to select
the programme number with the channel
you wish to name. When the programme you
want to name appears on the screen, select
the Label option and press . Next
to select a letter, number or
press
or
“-“ for a blank. Press
to confirm this
character. Select the other four characters in
the same way. After selecting all the
characters, press OK twice to store.
b) Label a channel using up to five characters.
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Level 1
OK
OK
OK
OK
Noise Reduction:
AV2 Output:
RGB Centring:
Picture Rotation:
Detail Set Up
Noise Reduction:
AV2 Output:
RGB Centring:
Picture Rotation:
Detail Set Up
Level 2
OK
Auto
TV
0
0
OK
Auto
TV
0
0
.
.
Menu System
15
continued...
If you have connected a decoder to the
Scart :2/q or to a VCR connected to
this Scart, please remember to change back
the “AV2 Output” to “AUTO” or “TV” for
a correct unscrambling.
If you select “AUTO”, the output signal
will always be the same one that is
displayed on the screen.
To do this: after selecting the option, press
Then press
or
to select the desired
output signal: TV, AV1, AV3 or AUTO.
If your VCR supports Smartlink, this
procedure is not necessary.
AV2 OUTPUT
The “AV2 Output” option in the “Detail Set
Up” menu allows you to select the source to be
output from the Scart connector :2/q in
order you can record from this Scart any signal
coming from the TV or from an external
equipment connected to the Scart connector
:1/
or front connectors
3 and
3.
To cancel this function afterwards, select “Off”
instead of “Auto” in the step above.
To do this: after selecting the option, press
Then press
or
to select Auto. Finally
press OK to confirm and store.
NOISE REDUCTION
The “Noise Reduction” option in the “Detail Set
Up” menu allows to reduce automatically the
picture noise in case of a weak broadcasting
signal.
Level 3 / Function
GB
10
16
Menu System
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Set Up
Language/Country
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Picture Adjustment
Level 1
OK
OK
OK
OK
Noise Reduction:
AV2 Output:
RGB Centring:
Picture Rotation:
Detail Set Up
Noise Reduction:
AV2 Output:
RGB Centring:
Picture Rotation:
Detail Set Up
Level 2
OK
Auto
TV
0
0
OK
Auto
TV
0
0
To do this: after selecting the option, press
.
Then press
or
to correct any slant of the
picture between -5 and +5 and finally press OK
to store.
PICTURE ROTATION
Because of the earth’s magnetism, the picture
might slant. In this case, you can correct the
pictures slant by using the option “Picture
Rotation” in the “Detail Set Up” menu.
To do this: while watching an RGB source select
the “RGB Centring” option and press
. Then
press
or
to adjust the centre of the
picture between –10 and +10. Finally press OK
to confirm and store.
RGB CENTRING
When connecting an RGB source, such as a
“PlayStation”, you may need to readjust the
horizontal position of the picture. In that case,
you can readjust it through the “RGB Centring”
option in the “Detail Set Up”.
Level 3 / Function
25
153
101
98
TELETEXT
Index
Programme
News
Sport
Weather
. Press it again to cancel teletext mode.
Teletext
17
Fastext service lets you access pages with one button push.
While you are in Teletext mode and Fastext is broadcast, a colour coded menu appears at
the bottom of the teletext page. Press the colour button (red, green, yellow or blue) to access
the corresponding page.
Fastext
To Switch Off Teletext:
Press
.
To reveal concealed information (e.g: answer to a quiz):
Press
/
. Press it again to conceal the information.
To freeze a teletext page:
Some teletext pages have sub-pages which follow on automatically. To stop them, press
/
. Press it again to cancel the freeze.
To superimpose teletext on to the TV:
Whilst you are viewing teletext, press
To access the next or preceding page:
Press PROGR + (
) or PROGR - (
).
To Select a Teletext page:
Input 3 digits for the page number, using the numbered buttons.
• If you have made a mistake, retype the correct page number.
• If the counter on the screen continues searching, it is because this page is not available. In that case,
input another page number
To Switch On Teletext :
After select the TV channel which carries the teletext you wish
to view, press
.
Make sure to use a channel (TV Broadcast) with a strong signal, otherwise teletext errors
may occur.
Teletext is an information service transmitted by most TV stations. The index page of the
teletext service (usually page 100) gives you information on how to use the service. To
operate teletext, use the remote control buttons as indicated below.
Teletext
GB
11
audio outputs (Left/
Right) - phono jacks
21-pin Scart connector
(CENELEC standard)
including audio / video
input, S video input,
selectable audio / video
output and Smartlink
interface.
Other features:
• Teletext, Fastext, TOPtext
• Sleep Timer
• Wake UP Timer
• Smartlink (direct link between your TV set
and a compatible VCR. For more
information on Smartlink, please refer to
the Instruction Manual of your VCR).
• TV system Autodetection.
Accessories supplied:
1 Remote Control (RM-887)
2 Batteries (IEC designated)
20
Additional Information
Ecological Paper- Totally Chlorine Free
Design and specifications are subject to change without notice.
Front Terminals
…3 video input – phono jack
3 audio input – phono jacks
headphones jack
:2/q
Rear Terminals
:1/
21-pin scart connector
(CENELEC standard)
including audio/video
input, RGB input, TV
audio/video output.
Picture Tube:
Flat Display FD Trinitron
21” (approx. 55 cm. measured
diagonally)
Weight:
Approx. 26 Kg.
Dimensions (w x h x d) :
Approx. 545 x 446 x 485 mm.
Standby Power Consumption:
0.5 W
Power Consumption:
60 W
Colour system:
PAL, SECAM
NTSC 3.58, 4.43 (only Video In)
Channel Coverage:
VHF:
E2-E12
UHF:
E21-E69
CATV:
S1-S20
HYPER: S21-S41
D/K:
R1-R12, R21-R69
Sound Output:
2 x 14 W (music power)
2 x 7 W (RMS)
TV system:
Depending on your country selection:
B/G/H, D/K
Specifications
• Press the
+/- button on the remote control.
• Check that “TV Speakers” is “On” on the “Sound
Adjustment” menu.
• Check that headphones are not connected.
• Using the menu system, select the “Picture
Adjustment” menu and select “Reset” to return to
factory settings.
• Turn off any equipment connected to the Scart
connector on the rear of the TV.
• Using the menu system, enter to the “Language/
Country” menu and select the country in which you
operate the TV set. For Cyrillic languages, we
agreement to select Russia country in the case that your
own country does not appear in the list.
• Using the menu system, select the “Picture Rotation”
option in the “Detail Set Up” menu to correct the
picture slant.
Good picture, no sound.
No colour on colour programmes.
Distorted picture when changing
programmes or selecting teletext.
Wrong characters appear when
viewing teletext.
Picture slanted
• Contact to your nearest Sony service centre.
The standby indicator
on the TV
flashes even though the “On Timer”
Additional Information
In case of problems, have your TV serviced by qualified personnel. Never open the
casing yourself.
• Replace the batteries.
Remote control does not function.
21
• Using the menu system, select the “Set Up” menu.
Then enter to “Detail Set Up” option and set “AV2
Output” to “TV”.
• Check that the optional equipment is on and press the
button repeatedly on the remote control until the
correct input symbol is displayed on the screen.
No picture or no menu information
from equipment connected to the
Scart connector.
No unscrambling or unstable picture
whilst viewing a scrambling channel
with a decoder connected through
the Scart connector :2/q.
• Using the menu system, select the “Picture
Adjustment” menu and select “Reset” to return to the
factory settings.
Poor or no picture (screen is dark),
but good sound.
• Using the menu system, select the “Manual
Programme Preset” menu and adjust Fine Tuning
(AFT) to obtain better picture reception.
• Using the menu system, select the “Noise Reduction”
option in the “Detail Set Up” menu and select
“Auto” to reduce the noise in the picture.
• Check the aerial connection.
• Plug the TV in and press the
button on the front of
TV.
• If the standby indicator
is on, press
button on
the remote control.
No picture (screen is dark) and no
sound.
Noisy picture when viewing a T
Download PDF

advertising