Sony | FM | User's Manual | Sony FM User's Manual

3-242-050-21 (1)
3 A
AUDIO OUT
FRONT
SUB OUT (MONO)
MG-MS/FM/MW/LW
Compact Disc
Player
AUDIO OUT
REAR
Installation/Connections
B
BUS AUDIO IN
BUS CONTROL IN
BUS AUDIO IN
Source selector*
*
XA-C30
BUS CONTROL IN
MEX-5DI
* not supplied
Sony Corporation © 2002 Printed in Japan
1
121 mm
142.5 mm
19 mm
9.5 mm
59 mm
170 mm
Dimensions include unit size, front panel and disc tray open, etc.
2
TO
P
5
4
8
The numbers in the list are keyed to those in the
instructions.
9
Front speaker
Power amplifier
Rear speaker
CD/MD changer
For the use of release key 9, see the supplied
operating instructions.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
TO
P
Connection example (3)
Note (3-A)
Be sure to connect the earth cord before connecting
the amplifier.
×2
Equipment used in illustrations (not supplied)
Active subwoofer
• This unit is designed for negative earth 12 V
DC operation only.
• Do not get the wires under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the yellow and red power input leads
only after all other leads have been connected.
• Run all earth wires to a common earth
point.
• Be sure to insulate any loose unconnected
wires with electrical tape for safety.
6
×4
7
Parts Iist (2)
Notes on the power supply cord (yellow)
• When connecting this unit in combination with
other stereo components, the connected car
circuit’s rating must be higher than the sum of
each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
3
2
1
Cautions
Before installation (1)
Do not install the unit where its operation
interferes with driving.
Example:
— Opening and closing of the front panel or
disc tray interfere with operation of the gear
shift.
— With the front panel open, operation of
hazard lamps, switches etc., is impaired.
Tip (3-B- )
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
4
Source selector
Supplied with the CD/MD changer
*
XA-C30
3
Supplied with XA-C30
*2
BUS AUDIO IN
/AUX IN*4
SUB OUT (MONO)
AUDIO OUT
FRONT
BUS AUDIO IN
/ AUX IN
SUB OUT
from car aerial
BUS
CONTROL IN
*1
Fuse (10 A)
*1
AUDIO OUT
REAR
7
Black
Blue/white striped
AMP REM
1
3
Max. supply current 0.3 A
Blue
2
ANT REM
Max. supply current 0.1 A
*1 RCA pin cord (not supplied)
Light blue
4
*2 Auxiliary optional equipment such as portable DVD player (not supplied)
ATT
*3 supplied with the auxialiry equipment
Orange/white striped
5
*4 Be sure to match the color-coded code for audio to the appropriate jacks from the unit.
If you connect an optional CD/MD unit, you cannot use AUX IN terminal.
ILLUMINATION
Red
6
Yellow
7
2
Connection diagram (4)
1 To a metal surface of the car
First connect the black earth lead, then connect
the yellow and red power input leads.
2 To the power aerial control lead or power
supply lead of aerial booster amplifier
Notes
• It is not necessary to connect this lead if there
is no power aerial or aerial booster, or with a
manually-operated telescopic aerial.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
4
1
•
•
9
2
•
•
•
1
•
•
•
3
TO
P
3 To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4 To the interface cable of a car telephone
5 To a car’s illumination signal
•
4
5
•
3
Be sure to connect the black earth lead to it first.
6 To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energised at all times.
Be sure to connect the black earth lead to it
first.
• When your car has a built-in FM/MW/LW aerial
in the rear/side glass, see “Notes on the control
and power supply leads.”
7 To the +12 V power terminal which is energised
6
•
3
1
•
3
7
•
•
at all times
Be sure to connect the black earth lead to it first.
Notes on the control and power supply leads
• The power aerial control lead (blue) supplies +12 V
DC when you turn on the tuner or when you
activate the AF (Alternative Frequency), TA (Traffic
Announcement) function.
• When your car has built-in FM/AM aerial in the
rear/side glass, connect the power aerial control
lead (blue) or the accessory power input lead (red)
to the power terminal of the existing aerial
booster. For details, consult your dealer.
• A power aerial without relay box cannot be used
with this unit.
Memory hold connection
When the yellow power input lead is connected,
power will always be supplied to the memory circuit
even when the ignition key is turned off.
•
5 *
1
182
mm
8
53 m
m
TO
P
1
with the TOP marking up
2
4
3
Dashboard
Fire wall
1
TO
P
4
5
2
5
6
Bend these claws outward
for a tight fit, if necessary.
3
6
6
Precautions
•Choose the installation location carefully so
that the unit will not interfere with normal
driving operations.
•Avoid installing the unit in areas subject to
dust, dirt, excessive vibration, or high
temperatures, such as in direct sunlight or near
heater ducts.
•Use only the supplied mounting hardware for
a safe and secure installation.
Mounting angle adjustment
5
Warning when installing in a car
without ACC (accessory)
position on the ignition key
switch
Be sure to press (OFF) on the unit for two
seconds to turn off the clock display after
turning off the engine.
•
•
(OFF)
(OFF)
•
When you press (OFF) only momentarily, the
clock display does not turn off and this causes
battery wear.
Adjust the mounting angle to less than 30°.
5
Reset button
Mounting example (5)
Installation in the dashboard
When the installation and connections are
completed, be sure to press the reset button with
a ballpoint pen, etc.
When installing this unit, be sure to close the
front panel of the unit and attach the front
panel cover 8. (5-*)
•Do not push the LCD display directly. The
display may break and cause injury to your
fingers. When installing the unit, be sure to
attach the supplied front panel cover 8.
•Do not hold the unit by its front panel or disc
tray when installing as this can damage the
unit, or cause malfunction.
Mounting the unit in a Japanese
car (6)
You may not be able to install this unit in some
makes of Japanese cars. In such a case, consult
your Sony dealer.
Note
To prevent malfunction, install only with the
supplied screws 5.
5
8
*
•
8
•
Note
The unit makes some noise during the initial
settings, this is not a malfunction.
6
5
6
A
B
TOYOTA
NISSAN
5
5
max. size
5 × 8 mm
max. size
5 × 8 mm
to dashboard/centre console
to dashboard/centre console
5
Bracket
max. size
5 × 8 mm
5
Bracket
Bracket
Existing parts supplied with your car
max. size
5 × 8 mm
Bracket
Existing parts supplied with your car
Download PDF

advertising