Lutron 3-Wire Fluorescent Power Module Spec Submittal Part

Lutron 3-Wire Fluorescent Power Module Spec Submittal Part
Lutron®
3-Wire Fluorescent Power Module
Power Modules
369355c 1 06.22.16
3-Wire Fluorescent Power Module
Description
• Provides capability for a zone on a GRAFIK Eye® control
unit (or other product) to dim fluorescent lights that
have Lutron® Hi-lume® and Eco-10® (Eco Series) linevoltage control electronic dimming ballasts.
• Utilizes Softswitch® arcless switching technology.
• Up to 3 power modules may be wired on a single
GRAFIK Eye® zone.
• Models available for 120 V~ control power.
• Models available for 120 V~ or 120 –277 V~
load power.
Works with 120 V~ versions of:
• Lutron® 3-wire fluorescent dimmers (consult Lutron for
Vierti®); see approved list in the dimmers & switches
specification guide at www.lutron.com
• GRAFIK Eye® QS control units
• GRAFIK Eye® 3000 Series control units
• LP, LCP, and GP dimming panels
• HomeWorks® and HomeWorks® QS remote power
panels
Models and Capacities
Model Number
PHPM-3F-DV-WH
PHPM-3F-120-WH
®
Job Name:
Job Number:
Control Power
120 V~
120 V~
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Load Power
120 –277 V~
120 V~
Capacity
16 A
16 A
Page 1
Lutron®
3-Wire Fluorescent Power Module
Power Modules
369355c 2 06.22.16
Specifications
Regulatory Approvals
•
•
•
•
UL® listed
CSA certified
NOM certified
Complies with requirements for use in other spaces
used for environmental air (plenums) per
NEC® 2014 300.22(C)(3)
Environment
• 32 °F to 104 °F (0 °C to 40 °C). Relative humidity
less than 90% non-condensing.
• Indoor use only.
• Maximum heat output of module: 15 BTU / hour.
Mounting
• Surface- or recess-mount.
Power
• Control voltage: 120 V~
• Load voltage: 120 V~ only for PHPM-3F-120-WH
120 –277 V~ for PHPM-3F-DV-WH
• Capacity: Full 16 A
120 V~: 1920 W
120 –277 V~: 1920 – 4432 W
• Frequency: 50 / 60 Hz, phase-to-neutral.
• Load (output) power: Phase independent of control
device / control voltage.
Sources/Load Types
• Operates Lutron® Hi-lume®, Eco-10® (Eco Series),
Compact SETM, EcoSystem®, and EcoSystem®
Compact line-voltage control electronic dimming
ballasts with a smooth continuous Square-Law
dimming curve.
Key Design Features
• Patented RTISSTM circuitry compensates in real time
for incoming line-voltage variations: Compensates for
+/-2% change in RMS voltage / cycle and
+/-2% Hz change in frequency / second.
• Provides air-gap off.
• Module protects itself during temporary over-current
conditions on dimmed output.
• Two LEDs on front of unit provide diagnostic information
(visible when faceplate is removed).
Terminals
• Accept up to two 12 AWG (2.5 mm2) wires.
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page 2
Lutron®
3-Wire Fluorescent Power Module
Power Modules
369355c 3 06.22.16
Dimensions
All dimensions shown as: in (mm)
1.2 (30.5)
1.0 (25)
5.1
(129.5)
6.3
(160)
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page 3
Lutron®
3-Wire Fluorescent Power Module
Power Modules
369355c 4 06.22.16
Mounting
• Mount in 2-gang U.S. wallbox 3.5 in (89 mm) deep or
4 in x 4 in (102 mm x 102 mm) junction box 2.1 in
(53 mm) deep.
• Indoor use only.
• This device generates heat; mount only where ambient
temperature is 32 °F to 104 °F (0 °C to 40 °C).
• Mount with arrows facing up to ensure adequate
cooling.
Mount to 2-gang U.S. wallbox
• Allow 4.5 in (114 mm) above and below unit and
between faceplates when mounting several in a
vertical layout.
• Mount so line (mains) voltage wiring is at least 6 ft
(1.8 m) from sound or electronic equipment and
wiring.
• Mount within 7° of true vertical.
Mount to 4 in x 4 in (102 mm x 102 mm),
2.1 in (53 mm) deep U.S. junction box
Mount to 4 in x 4 in (102 mm x 102 mm), 2.1 in (53 mm) deep
U.S. junction box with barrier
(for 277 V~ model if required by local electrical code)
Barrier
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page 4
Lutron®
3-Wire Fluorescent Power Module
Power Modules
369355c 5 06.22.16
Wiring
• Pull 12 AWG (2.5 mm2) copper (Cu) wires [167 °F (75 °C) minimum] for input power and load circuit.
• Strip 1/2 in (12 mm) insulation from wires before connecting.
• Run separate neutral for load circuit - no common neutrals.
Single Power Feed
The power module may be on the same circuit as the control unit only if the total load does not exceed the
rating of the breaker.
GRAFIK Eye® QS
Circuit breaker
1 2 3 4 5 6 L N
L/H
N
120 V~
Wire to appropriate
zone
Lutron®
Ballast
L/H
N
SH
DH
Zone in
Control Neutral
Legend
L /H
N
SH
DH
Line / Hot
Neutral
Switched Hot
Dimmed Hot
Ground
Not Used
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page 5
Lutron®
3-Wire Fluorescent Power Module
Power Modules
369355c 6 06.22.16
Wiring
(continued)
Multiple Power Feeds
The load breaker may be on a different phase than the control breaker.
GRAFIK Eye® QS
1 2 3 4 5 6 L N
N
120 V~
L/H
Wire to appropriate
zone
Control breaker
Load breaker
L/H
N
Load wiring 1
Lutron®
Ballast
L/H
N
SH
DH
Zone in
Control Neutral
Legend
L/H
N
SH
DH
1
Line / Hot
Neutral
Switched Hot
Dimmed Hot
Ground
Not Used
Load feed: 120 V~ for PHPM-3F-120-WH; 120 – 277 V~ for PHPM-3F-DV-WH
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page 6
Lutron®
3-Wire Fluorescent Power Module
Power Modules
369355c 7 06.22.16
Wiring
(continued)
Multiple Power Modules to a Single GRAFIK Eye® Zone
Shown with separate feeds for control and loads. All breakers must be turned off prior to installing or servicing
the modules. Up to 3 power modules may be wired to a single zone.
GRAFIK Eye® QS
1 2 3 4 5 6 L N
Wire to appropriate zone
N
L/H
120 V~
Control breaker
Load breaker
L/H
N
Load wiring 1
for Power
Module #1
L/H
N
Lutron®
Ballast
SH
DH
Zone in
Control Neutral
Load breaker
L/H
N
Load wiring 1
for Power
Module #2
L/H
N
Lutron®
Ballast
SH
DH
Zone in
Control Neutral
Load breaker
L/H
N
L/H
N
Load wiring 1
for Power
Module #3
1
Lutron®
Ballast
SH
DH
Zone in
Control Neutral
Load feed: 120 V~ for PHPM-3F-120-WH; 120 – 277 V~ for PHPM-3F-DV-WH
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page 7
Lutron®
3-Wire Fluorescent Power Module
Power Modules
369355c 8 06.22.16
Wiring
(continued)
Multi-location Wiring
The power module may be on the same circuit/control zone as the control device only if the total load does not
exceed the rating of the breaker (120 V~ only).
Circuit breaker
L/H
N
Load wiring 1
LutronR
Ballast
L/H
N
SH
DH
DH
(yellow
or orange
wire)
Zone in
Control Neutral
3-wire
fluorescent
dimmer
120 V~
(main
dimmer)
SH
(red wire)
Cap off
3-wire
fluorescent
dimmer
120 V~
(accessory/
companion
dimmer or
3-way switch)
H/L
N
120 V~
Legend
L/H
N
SH
DH
1
Line / Hot
Neutral
Switched Hot
Dimmed Hot
Ground
Not Used
For specific wire colors, see the wallbox lighting controls
catalog at www.lutron.com/wallbox catalog
Load feed: 120 V~ for PHPM-3F-120-WH; 120 – 277 V~ for PHPM-3F-DV-WH
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Page 8
Lutron®
3-Wire Fluorescent Power Module
Power Modules
369355c 9 06.22.16
Wiring
(continued)
Wiring a Power Module to an LP, LCP, GP, or HomeWorks® Panel
Up to three 3-wire fluorescent power modules may be wired to an output of a 120 V~ LP or LCP panel. The
load type for the output must be set as Eco-10® or Hi-lumeR fluorescent load type on the panel’s circuit selector
(for an LP or GP panel), controller (for an LCP panel), or HomeWorks® software (for a HomeWorks® panel).
Wire to appropriate output
Load
wiring1
1
L/H
N
LutronR
Ballast
L/H
N
SH
DH
Zone In
Control
Neutral
(1) 14 to 10 AWG
(2.0 to 4.0 mm2)
Dimmed
Hot
(1) 14 to 10 AWG
(2.0 to 4.0 mm2) Neutral
DH
DH
DH
DH
H
N
N
N
N
N
Load feed: 120 V~ if used with PHPM-3F-120-WH power module
120 – 277 V~ if used with PHPM-3F-DV-WH power module
120 V~ Branch Circuit
Breakers
Neutral Lug
Power (Line / Hot)
(3) 14 to 2/0 AWG (2.0 to 70 mm2)
®
Job Name:
Job Number:
S P E C I F I C AT I O N S U B M I T TA L
Model Numbers:
Neutral (1) 14 to 2/0 AWG
(2.0 to 70 mm2)
Page 9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement