Sony HT-DDW990 User's Manual

3-097-352-11(1)
Home Theatre
System
Operating Instructions
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record the
serial number in the space provided below. Refer to them whenever you call
upon your Sony dealer regarding this product.
Serial No.
Model No.
HT-DDW990
©2007 Sony Corporation
WARNING
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
To prevent fire, do not cover the ventilation of the
apparatus with newspapers, table-cloths, curtains,
etc. And don’t place lighted candles on the
apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
Install this system so that the power cord can be
unplugged from the wall socket immediately in the
event of trouble.
Don’t throw away batteries with
general house waste; dispose of
them correctly as chemical waste.
For customers in the United
States
WARNING
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment
and receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
You are cautioned that any changes or modification
not expressly approved in this manual could void
your authority to operate this equipment.
Note to CATV system installer:
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
2US
This reminder is provided to call CATV system
installer’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
About This Manual
Note for the supplied remote
• The instructions in this manual are for model
HT-DDW990. In this manual, models of area code
U is used for illustration purposes unless stated
otherwise. Any difference in operation is clearly
indicated in the text, for example, “Models of area
code CA only”.
(RM-AAP017)
The AUX button on the remote is not available
for receiver operation.
The HT-DDW990 consists of:
• Receiver
• Speaker system
– Front speakers
– Center speaker
– Surround speakers
– Sub woofer
STR-K990
SS-MSP900
SS-CNP680
SS-SRP900
SA-WP780
• The instructions in this manual describe the
controls on the supplied remote. You can also use
the controls on the receiver if they have the same
or similar names as those on the remote.
About area codes
The area code of the receiver you purchased is
shown on the lower right portion of the rear panel
(see the illustration below).
L
R
ONT A
ERS
L
R
SURROUND
CENTER
Area code
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
This receiver incorporates Dolby* Digital and Pro
Logic Surround and the DTS** Digital Surround
System.
* Manufactured under license from Dolby
Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol
are trademarks of Dolby Laboratories.
** “DTS” and “DTS Digital Surround” are
registered trademarks of DTS, Inc.
This receiver incorporates High-Definition
Multimedia Interface (HDMITM) technology.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
3US
Table of Contents
Getting Started
Enjoying Surround Sound
Description and location of parts...................5
1: Installing speakers ...................................15
2: Connecting speakers................................17
3a: Connecting the audio components.........19
3b: Connecting the video components ........20
4: Connecting the antennas..........................28
5: Preparing the receiver and the remote .....29
6: Selecting the speaker system ...................30
7: Calibrating the appropriate settings
automatically
(AUTO CALIBRATION) .......................31
8: Adjusting the speaker levels and
balance (TEST TONE) ...........................34
Enjoying Dolby Digital and DTS surround
sound (AUTO FORMAT DIRECT)....... 49
Selecting a pre-programmed sound field .... 51
Using only the front speakers and sub
woofer (2CH STEREO)......................... 54
Resetting sound fields to the initial
settings ................................................... 54
Tuner Operations
Listening to FM/AM radio.......................... 55
Presetting radio stations .............................. 56
Other Operations
Playback
Selecting a component.................................36
Listening/Watching a component ................38
Amplifier Operations
Navigating through menus...........................40
Adjusting the level (LEVEL menu).............43
Adjusting the tone (TONE menu) ...............44
Settings for the surround sound
(SUR menu)............................................44
Settings for the tuner (TUNER menu).........45
Settings for the audio (AUDIO menu).........45
Settings for the video (VIDEO menu).........46
Settings for the system (SYSTEM menu) ...47
Calibrating the appropriate settings
automatically (A. CAL menu)................49
4US
Switching between digital and analog audio
(INPUT MODE) .................................... 59
Enjoying the DIGITAL MEDIA PORT
(DMPORT) ............................................ 60
Naming inputs............................................. 63
Changing the display .................................. 63
Using the Sleep Timer ................................ 64
Recording using the receiver....................... 64
Using the Remote
Programming the remote ............................ 65
Additional Information
Glossary ...................................................... 70
Precautions.................................................. 71
Troubleshooting .......................................... 73
Specifications.............................................. 76
Index ........................................................... 79
Getting Started
Getting Started
Description and location of parts
Receiver
Front panel
1 2
4
3
5
6
DISPLAY
INPUT MODE
7
?/1
MASTER VOLUME
INPUT SELECTOR
SPEAKERS
(OFF/A/B/A+B)
AUTO CAL MIC
MEMORY/
ENTER
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
MUTING
9
8
VIDEO 3 IN/PORTABLE AV IN
PHONES
VIDEO
qj qh
L AUDIO R
qg
qf qd
qs
qa
q;
.
Name
Function
Name
Function
A ?/1
(on/standby)
Press to turn the receiver on
or off (page 29, 38, 39, 54).
F INPUT MODE
B SPEAKERS
(OFF/A/B/A+B)
Press to select the speaker
system (page 30).
Press to select the input
mode when the same
components are connected
to both digital and analog
jacks (page 59).
C Display
The current status of the
selected component or a list
of selectable items appears
here (page 7).
G MASTER
VOLUME
Turn to adjust the volume
level of all speakers at the
same time (page 35, 36, 38,
39).
D Remote sensor
Receives signals from
remote commander.
H MUTING
Press to mute the sound
(page 36).
E DISPLAY
Press to select information
displayed on the display
(page 63).
I AUTO CAL
Press to activate the Auto
Calibration function (page
32).
J INPUT
SELECTOR
Turn to select the input
source to playback (page
36).
continued
5US
Name
Function
K 2CH
Press to select a sound field
(page 49, 51, 54).
A.F.D.
MOVIE
MUSIC
L TUNING +/–
Press to scan a station (page
55, 58).
M TUNING MODE
Press to select the tuning
mode (page 55, 58).
N MEMORY/
ENTER
Press to store a station or
enter the selection when
selecting the settings (page
29, 57).
O VIDEO 3 IN/
PORTABLE AV
IN jacks
Connects to a camcorder or
video game (page 27, 36).
P AUTO CAL MIC Connects to the supplied
optimizer microphone for
jack
the Auto Calibration
function (page 31).
Q PHONES jack
6US
Connects to headphones
(page 73).
About the indicators on the display
SW
2
3
LFE
SP A ; D
SP B
L
C
R
SL
S
SR
4
5
6
; PL II
; PL
qf
7
8
OPT DTS
COAX
qd
9
MEMORY
D.RANGE
qs
q;
ST
MONO
qa
Name
Function
Name
Function
A SW
Lights up when the audio signal
is output from the SUB
WOOFER jack.
G OPT
B LFE
Lights up when the disc being
played back contains an LFE
(Low Frequency Effect)
channel and the LFE channel
signal is actually being
reproduced.
C SP A/SP B
Lights up according to the
speaker system used (page 30).
However, these indicators do
not light up if the speaker output
is turned off or if headphones
are connected.
Lights up when VIDEO 2 input
is selected. However,
“UNLOCK” appears on the
display if no digital signal is
input through the OPTICAL
jack.
“OPT” also lights up when SAT
input is selected if
– INPUT MODE is set to
“AUTO IN” and the source
signal is a digital signal being
input through the OPTICAL
jack.
– INPUT MODE is set to “OPT
IN” (page 59).
H DTS
D; D
Lights up when the receiver is
decoding Dolby Digital signals.
Note
When playing a Dolby Digital
format disc, be sure that you
have made digital connections
and that INPUT MODE is not
set to “ANALOG” (page 59).
Lights up when the receiver is
decoding DTS signals.
Note
When playing a DTS format
disc, be sure that you have made
digital connections and that
INPUT MODE is not set to
“ANALOG” (page 59).
I MEMORY
E ; PL II
Lights up when the Pro Logic II
Movie/Music decoder is
activated.
Lights up when a memory
function, such as Preset
Memory (page 56), etc., is
activated.
F ; PL
Lights up when the receiver
applies Pro Logic processing to
2 channel signals in order to
output the center and surround
channel signals.
J Tuner
indicators
Lights up when using the
receiver to tune in radio stations
(page 55), etc.
K Preset
station
indicators
Lights up when using the
receiver to tune in preset radio
stations. For details on
presetting radio stations, see
page 56.
continued
7US
Getting Started
1
Name
Function
L D.RANGE
Lights up when dynamic range
compression is activated (page
41).
M COAX
Lights up when INPUT MODE
is set to “AUTO IN” and the
source signal is a digital signal
being input through the
COAXIAL jack, or when
INPUT MODE is set to “COAX
IN” (page 59).
N Playback
channel
indicators
The letters (L, C, R, etc.)
indicate the channels being
played back. The boxes around
the letters vary to show how the
receiver downmixes the source
sound.
Front Left
Front Right
Center (monaural)
Surround Left
Surround Right
Surround (monaural or the
surround components obtained
by Pro Logic processing)
Example:
Recording format (Front/
Surround): 3/2.1
Sound Field: A.F.D. AUTO
L
R
C
SL
SR
S
SW
L
SL
8US
C
R
SR
Rear panel
2
Getting Started
1
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
Y
AM
VIDEO 2/
BD IN
PB/CB
COAXIAL
DVD
IN
PR/CR
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
MONITOR
DMPORT
DVD IN
VIDEO 1 IN MONITOR OUT
COMPONENT VIDEO
R
L
L
L
L
R
R
R
R
L
L
L
AUDIO OUT
OUT
IN
SA-CD/CD/CD-R
6
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
5
VIDEO 1
SUB
WOOFER
FRONT B
4
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
3
A DIGITAL INPUT/OUTPUT section
C SPEAKERS section
OPTICAL IN
jacks
Connects to a DVD
player, etc. The
COAXIAL jack
provides a better
COAXIAL IN quality of loud
jack
sound (page 21, 24,
26).
HDMI IN/
OUT jacks*
DMPORT
jack
Connects to a DVD
player or a Blu-ray
disc player. The
image and the
sound are output to
a TV or a projector
(page 21).
Connects to a
DIGITAL MEDIA
PORT adapter
(page 61).
Connects to
speakers (page 17).
Connects to sub
woofer (page 17).
D VIDEO/AUDIO INPUT/OUTPUT
section
AUDIO IN/
White (L) OUT jacks
Red (R)
B COMPONENT VIDEO INPUT/
OUTPUT section
Green
(Y)
Blue
(PB/CB)
Red
(PR/CR)
COMPONENT
VIDEO
INPUT/
OUTPUT
jacks*
Connects to a DVD
player, TV,
satellite tuner, etc.
You can enjoy high
quality image
(page 23–26).
Yellow
Connects to the
video and audio
jacks of a VCR,
DVD player, etc.
(page 23–27).
VIDEO IN/
OUT jacks*
E AUDIO INPUT/OUTPUT section
AUDIO IN/
White (L) OUT jacks
Red (R)
Connects to a
Super Audio CD
player, CD
recorder, etc. (page
19, 23).
continued
9US
F ANTENNA section
Remote commander
FM
ANTENNA
jack
Connects to the
FM wire antenna
supplied with this
receiver (page 28).
AM
ANTENNA
terminals
Connects to the
AM loop antenna
supplied with this
receiver (page 28).
* You can watch the selected input image when you
connect the HDMI OUT or MONITOR OUT jack
to a TV (page 23).
You can use the supplied remote to operate the
receiver and to control the Sony audio/video
components that the remote is assigned to
operate.
You can also program the remote to control
non-Sony audio/video components. For
details, see “Programming the remote” (page
65).
RM-AAP017
wk
wj
?/1
TV RM SET UP AV ?/1
1
2
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3 DVD
wh
wg
wf
SAT
TV
SA-CD/CD TUNER
AUX
DMPORT
2CH
A.F.D.
RECEIVER
MOVIE
3
4
MUSIC
SLEEP FM MODE D. TUNING AUTO CAL
1
2
3
4
5
6
7
8
9
CLEAR
0/10
5
6
7
– /– –
wd
ws
MEMORY
DISPLAY
V
wa
w;
ql
ENTER
>10
GUIDE
B
9
B
v
RETURN/
EXIT
MENU
.
REPLAY ADVANCE
<
<
TUNING –
m
8
OPTIONS
TOOLS
q;
qa
>
TUNING +
H
M
X
x
qs
DISC SKIP
qk
TV VOL
MASTER VOL
qj
qh
qg
10US
TV CH
PRESET
MUTING
qd
DVD
TOP MENU MENU
F1
F2
TV INPUT
WIDE
qf
Name
Function
Function
D RECEIVER
Press to activate the receiver
operation (page 40).
E D.TUNING
Press to enter direct tuning
mode.
F AUTO CAL
Press to activate the Auto
Calibration function.
G Numeric
buttons
(number 5a))
Press to
– preset/tune to preset
stations.
– select track numbers of the
CD player, VCD player, LD
player, DVD player, MD
deck, DAT deck, or tape
deck. Press 0/10 to select
track number 10.
– select channel numbers of
the VCR, satellite tuner,
Blu-ray disc recorder, PSX,
DVD/VHS COMBO, or
DVD/HDD COMBO.
Press TV (wj) and then press
the numeric buttons to select
the TV channels.
H ENTER
Press to enter the value after
selecting a channel, disc or
track using the numeric
buttons of the VCR, CD
player, VCD player, LD
player, MD deck, DAT deck,
tape deck, satellite tuner, Bluray disc recorder, or PSX.
To enter the value of Sony
TV, press TV (wj) and then
press ENTER.
B ?/1
Press to turn the receiver on or
(on/standby) off.
To turn off all components,
press ?/1 and AV ?/1 (A) at
the same time (SYSTEM
STANDBY).
C Input buttons Press one of the buttons to
select the component you want
to use. When you press any of
the input buttons, the receiver
turns on. The buttons are
factory assigned to control
Sony components as follows.
You can program the remote to
control non-Sony components
following the steps in
“Programming the remote” on
page 65.
Button
Assigned Sony
component
VIDEO 1
VCR (VTR mode 3)
VIDEO 2
VCR (VTR mode 2)
VIDEO 3
VCR (VTR mode 1)
DVD
DVD player
SAT
Satellite tuner
TV
TV
SA-CD/CD Super Audio CD/
CD player
TUNER
Built-in tuner
AUX
Not assigned
DMPORT
DIGITAL MEDIA
PORT adapter
MEMORY
Press to store a station during
tuner operation.
I DISPLAY
Press to select information
displayed on the TV screen of
the VCR, VCD player, LD
player, DVD player, CD
player, MD deck, Blu-ray disc
recorder, PSX, satellite tuner,
DVD/VHS COMBO, or
DVD/HDD COMBO.
To select information of Sony
TV, press TV (wj) and then
press DISPLAY.
continued
11US
Getting Started
A AV ?/1
Press to turn on or off the
(on/standby) audio/video components that
the remote is programmed to
operate.
To turn the TV on or off, press
TV (wj) and then press AV
?/1.
If you press ?/1 (B) at the
same time, it will turn off the
receiver and other components
(SYSTEM STANDBY).
Note
The function of the AV ?/1
switch changes automatically
each time you press the input
buttons (C).
Name
Name
Function
J OPTIONS
TOOLS
Press to display and select
items from the option menus
for DVD player or
DVD/VHS COMBO.
To display the options of Sony
TV, press TV (wj) and then
press OPTIONS TOOLS.
K MENU
Press to display the menus of
the receiver, VCR, DVD
player, satellite tuner, Blu-ray
disc recorder, PSX, DVD/
VHS COMBO, or DVD/HDD
COMBO on the TV screen.
Then, use V/v/B/b and
to
perform menu operations.
To display the menus of Sony
TV, press TV (wj) and then
press MENU.
L ./>b)
m/Mb)
Ha)b)
12US
Press to skip tracks of the
VCR, CD player, VCD
player, LD player, DVD
player, MD deck, DAT deck,
tape deck, Blu-ray disc
recorder, PSX, DVD/VHS
COMBO, or DVD/HDD
COMBO.
Press to
– search tracks in the forward/
backward direction of the
CD player, VCD player,
DVD player, LD player,
MD deck, Blu-ray disc
recorder, PSX, DVD/VHS
COMBO, or DVD/HDD
COMBO.
– fast forward/rewind of the
VCR, DAT deck, or tape
deck.
Press to start playback of the
VCR, CD player, VCD
player, LD player, DVD
player, MD deck, DAT deck,
tape deck, Blu-ray disc
recorder, PSX, DVD/VHS
COMBO, or DVD/HDD
COMBO.
Name
Function
Xb)
Press to pause playback or
recording of the VCR, CD
player, VCD player, LD
player, DVD player, MD
deck, DAT deck, tape deck,
Blu-ray disc recorder, PSX,
DVD/VHS COMBO, or
DVD/HDD COMBO. (Also
starts recording with
components in recording
standby.)
xb)
Press to stop playback of the
VCR, CD player, VCD
player, LD player, DVD
player, MD deck, DAT
deck, tape deck, Blu-ray
disc recorder, PSX, DVD/
VHS COMBO, or DVD/
HDD COMBO.
TUNING +/–
Press to scan a station.
M TV CH +a)/–
Press TV (wj) and then
press TV CH +/– to select
preset TV channels.
PRESET
+a)/–
Press to
– select preset stations.
– select preset channels of
the VCR, satellite tuner,
Blu-ray disc recorder,
DVD player, DVD/VHS
COMBO, or DVD/HDD
COMBO.
N F1, F2
Press F1 or F2 to select a
component.
• DVD/HDD COMBO
F1: HDD mode
F2: DVD mode
• DVD/VHS COMBO
F1: DVD mode
F2: VHS mode
TV INPUT
Press TV (wj) and then
press TV INPUT to select
the input signal (TV input or
video input).
WIDE
Press TV (wj) and then
press WIDE to select the
wide picture mode.
Function
Name
Function
O DVD TOP
MENU
Press to display the menu or
on-screen guide of the DVD
player on the TV screen.
Then, use V/v/B/b and
to
perform menu operations.
U
After pressing RECEIVER
(D), press MENU (K) for
receiver operation, then press
V/v/B /b to select the
settings.
After pressing DVD TOP
MENU (O) or DVD MENU
(O), press V/v/B/b to select
the settings, and then press
to enter the selection.
Press
also to enter the
selection of the receiver,
VCR, satellite tuner, DVD
player, Blu-ray disc recorder,
PSX, DVD/VHS COMBO, or
DVD/HDD COMBO.
DVD MENU
Press to display the menu of
the DVD player on the TV
screen. Then, use V/v/B/b
and
to perform menu
operations.
P MUTING
Press to mute the sound (page
36).
To mute the sound of the TV,
press TV (wj) and then press
MUTING.
Q TV VOL +/–
Press TV (wj) and then press
TV VOL +/– to adjust the TV
volume level.
MASTER
VOL +/–
R DISC SKIP
V GUIDE
Press to display the EPG
(Electronic Program Guide)
of the TV, DVD player,
satellite tuner, Blu-ray disc
recorder, PSX, or DVD/HDD
COMBO.
W CLEAR
Press to clear a mistake when
you press the incorrect
numeric button of the DVD
player, Blu-ray disc recorder,
PSX, satellite tuner, DVD/
VHS COMBO, or DVD/HDD
COMBO.
-/--
Press to select the channel
entry mode, either one or two
digit of the VCR or satellite
tuner.
To select the channel entry
mode of the TV, press TV
(wj) and then press -/--.
>10
Press to select track numbers
over 10 of the CD player,
VCD player, LD player, MD
deck, tape deck, TV, VCR, or
satellite tuner.
Press to adjust the volume
level of all speakers at the
same time.
Press to skip disc of the CD
player, VCD player, DVD
player, or MD deck (multidisc changer only).
S REPLAY < / Press to replay the previous
ADVANCE < scene or fast forward the
current scene of the DVD
player, Blu-ray disc recorder,
DVD/VHS COMBO, or
DVD/HDD COMBO.
T RETURN/
EXIT O
,
V/v/B/b
Press to
– return to the previous menu.
– exit the menu while the
menu or on-screen guide of
the VCD player, LD player,
DVD player, Blu-ray disc
recorder, PSX, DVD/VHS
COMBO, or satellite tuner
is displayed on the TV
screen.
To return to the previous
menu of Sony TV, press TV
(wj) and then press
RETURN/EXIT O.
X SLEEP
Press to activate the Sleep
Timer function and the
duration which the receiver
turns off automatically.
Y FM MODE
Press to select FM monaural
or stereo reception.
Z 2CH
Press to select a sound field
(page 49, 51, 54)
A.F.D.
MOVIE
MUSIC
continued
13US
Getting Started
Name
Name
Function
wj TV
Press to light up the button. It
changes the remote key
function to activate the
buttons with orange printing.
It also activate the DISPLAY
(I), OPTIONS TOOLS
(J), MENU (K),
RETURN/EXIT O (T),
(U), and V/v/B/b (U)
buttons to perform menu
operations for Sony TVs only.
wk RM SET UP
Press to set up the remote.
a)
The number 5, TV CH +, PRESET + and H
buttons have tactile dots. Use the tactile dots as
references when operating the receiver.
b)
This button is also available for DIGITAL MEDIA
PORT adapter operation. For details on the
function of the button, see the operating
instructions supplied with the DIGITAL MEDIA
PORT adapter.
Notes
• Some functions explained in this section may not
work depending on the model.
• The above explanation is intended to serve as an
example only. Therefore, depending on the
component, the above operation may not be
possible or may operate differently than described.
• The AUX button on the remote is not available for
receiver operation.
14US
1: Installing speakers
Installing the speakers on a flat
surface
Before you install the speakers and sub
woofer, be sure to attach the supplied foot pads
to prevent vibration or movement as shown in
the illustration below.
Example of a 5.1 channel
speaker system configuration
Installing the speakers on the
speaker stand
For greater flexibility in positioning the
speakers, use the optional WS-FV11 or
WS-FV10D speaker stand (available only in
certain countries). Be sure to detach the screw
from the speaker and use it when you install
the speaker to the speaker stand. For details,
refer to the operating instructions supplied
with the speaker stand.
AFront speaker (Left)
BFront speaker (Right)
CCenter speaker
DSurround speaker (Left)
ESurround speaker (Right)
FSub woofer
Tip
Since the sub woofer does not emit highly
directional signals, you can place it wherever you
want.
15US
Getting Started
This receiver allows you to use a 5.1 channel
system (5 speakers and one sub woofer).
To fully enjoy theater-like multi channel
surround sound requires five speakers (two
front speakers, a center speaker, and two
surround speakers) and a sub woofer (5.1
channel).
Installing the speakers on the
wall
3
Hang the speakers on the
screws.
Hook on the back of the speaker
You can install your speakers on the wall.
1
3/16 inch
(4.6 mm)
Prepare screws (not supplied)
that are suitable for the hook on
the back of each speaker as
shown in the illustrations
below.
13/32 inch
(10 mm)
more than 5/32 inch
(4 mm)
more than 1 inch (25 mm)
3/16 inch
(4.6 mm)
13/32 inch
(10 mm)
Hook on the back of the speaker
2
Fasten the screws to the wall.
The screws should protrude
7/32 to 9/32 inch (5 to 7 mm).
7/32 to 9/32 inch
(5 to 7 mm)
16US
Notes
• Use screws that are suitable for the wall material
and strength. As a plaster board wall is especially
fragile, attach the screws securely to a beam and
fasten them to the wall. Install the speakers on a
vertical and flat wall where reinforcement is
applied.
• Contact a screw shop or installer regarding the wall
material or screws to be used.
• Sony is not responsible for accident or damage
caused by improper installation, insufficient wall
strength or improper screw installation, natural
calamity, etc.
2: Connecting speakers
A
A
DVD IN
VIDEO 2/BD IN
Getting Started
F
D
B
OUT
HDMI
Y
PB/CB
PR/CR
VIDEO IN VIDEO OUT VIDEO IN VIDEO OUT
VIDEO IN
MONITOR
SAT IN
DVD IN
VIDEO 1 IN MONITOR OUT
COMPONENT VIDEO
R
L
L
L
L
L
L
L
AUDIO OUT
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFER
FRONT B
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
SPEAKERS FRONT B
terminalsa)
B
B
E
C
A Monaural audio cord (supplied)
B Speaker cord (supplied)b)
AFront speaker A (Left)
BFront speaker A (Right)
CCenter speaker
DSurround speaker (Left)
ESurround speaker (Right)
FSub woofer
a)
If you have an additional front speaker system,
connect them to the SPEAKERS FRONT B
terminals. You can select the front speakers you
want to use with the SPEAKERS (OFF/A/B/A+B)
button. For details, see “6: Selecting the speaker
system” (page 30).
b)
Use the long speaker cords to connect the surround
speakers and the short speaker cords to connect the
front and center speakers.
continued
17US
To connect the speakers
correctly
Check the speaker type by referring to the
speaker label* on the rear panel of the
speakers.
Character on
speaker label
Speaker type
L
Front left
R
Front right
SL
Surround left
SR
Surround right
* The center speaker and sub woofer do not have any
character on the speaker label. For details on the
speaker type, see page 3.
Tip
Use the supplied speakers to optimize the system’s
performance.
18US
3a: Connecting the audio components
Getting Started
Connecting a Super Audio CD/CD
player or CD recorder
The following illustration shows how to
connect a Super Audio CD player, CD player
or CD recorder.
After connecting your audio component,
proceed to “3b: Connecting the video
components” (page 20) or “4: Connecting the
antennas” (page 28).
Super Audio
CD player/
CD player/
CD recorder
A
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
Y
AM
VIDEO 2/
BD IN
PB/CB
COAXIAL
DVD
IN
PR/CR
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
MONITOR
DMPORT
SAT IN
DVD IN
VIDEO 1 IN MONITOR OUT
COMPONENT VIDEO
R
L
L
L
L
L
L
L
AUDIO OUT
R
R
OUT
IN
SA-CD/CD/CD-R
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFER
FRONT B
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
A Audio cord (not supplied)
19US
3b: Connecting the video components
How to connect your
components
Video input/output jack to be
connected
This section describes how to connect your
video components to this receiver. Before you
begin, refer to “Component to be connected”
below for the pages which describe how to
connect each component.
After connecting all your components,
proceed to “4: Connecting the antennas” (page
28).
The image quality depends on the connecting
jack. Refer to the illustration that follows.
Select the connection according to the jacks on
your components.
TV, etc. INPUT
jack
HDMI
COMPONENT
VIDEO
VIDEO
HDMI
COMPONENT
VIDEO
VIDEO
HDMI
COMPONENT
VIDEO
VIDEO
HDMI
COMPONENT
VIDEO
VIDEO
Component to be connected
Component
Page
With HDMI jack
21
TV
23
Receiver HDMI
OUT, MONITOR
OUT jack
?/1
MASTER VOLUME
DISPLAY
INPUT MODE
INPUT SELECTOR
SPEAKERS
(OFF/A/B/A+B)
AUTO CAL MIC
MEMORY/
ENTER
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
MUTING
VIDEO 3 IN/PORTABLE AV IN
PHONES
DVD player/DVD recorder
24
Satellite tuner/Set-top box
26
VCR
27
Camcorder, video game, etc.
27
VIDEO
L AUDIO R
Receiver INPUT
jack
Video component
OUTPUT jack
High quality image
Notes
• Connect image display components such as a TV
or a projector to the HDMI OUT or MONITOR
OUT jack on the receiver.
• Be sure to turn on the receiver when the video and
audio of a playback component are being output to
a TV via the receiver. If the power supply of the
receiver is not turned on, neither video nor audio is
transmitted.
20US
HDMI is the abbreviated name for HighDefinition Multimedia Interface. It is an
interface which transmits video and audio
signals in digital format.
Blu-ray disc player
DVD player
Audio
signals
Audio/video
signals
Audio
signals
B
A
TV, projector, etc.
Audio/video
signals
C
Audio/video
signals
A
A
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
Y
AM
VIDEO 2/
BD IN
PB/CB
COAXIAL
DVD
IN
PR/CR
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
MONITOR
DMPORT
SAT IN
DVD IN
VIDEO 1 IN MONITOR OUT
COMPONENT VIDEO
R
L
L
L
L
L
L
L
AUDIO OUT
R
R
OUT
IN
SA-CD/CD/CD-R
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFER
FRONT B
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
A HDMI cable (not supplied)
We recommend that you use a Sony HDMI cable.
B Coaxial digital cord (supplied)
C Optical digital cord (not supplied)
continued
21US
Getting Started
The sound is output from the TV speaker only
when a playback component and this receiver,
as well as this receiver and the TV are
connected via a HDMI jack.
To output the sound from the supplied
speakers and to take advantage of the multi
channel surround sound, be sure to
– connect the digital audio jacks on the
playback component to the receiver.
– turn off or mute the TV’s volume.
Connecting components with
HDMI jacks
If you connect a Blu-ray disc
player
Notes on digital audio signals
connection
• Be sure to change the factory setting of the
VIDEO 2 input button on the remote so that
you can use the button to control your Bluray disc player. For details, see
“Programming the remote” (page 65).
• You can also rename the VIDEO 2 input so
that it can be displayed on the receiver’s
display. For details, see “Naming inputs”
(page 63).
• When connecting optical digital cords, insert
the plugs straight in until they click into
place.
• Do not bend or tie optical digital cords.
• All the digital audio jacks are compatible
with 32 kHz, 44.1 kHz, 48 kHz, and 96 kHz
sampling frequencies.
Notes on HDMI connections
• This receiver may not be able to transfer
video or audio signals with certain types of
components.
• The multi/stereo area audio signals of a
Super Audio CD are not output.
• Be sure to turn on the receiver when the
video and audio of a playback component
are being output to a TV via the receiver. If
the power supply of the receiver is not
turned on, neither video nor audio is
transmitted.
• Audio signals (sampling frequency, bit
length, etc.) transmitted from a HDMI jack
may be restricted by the connected
component. Check the setup of the
connected component if the image is poor or
the sound does not come out of a component
connected via the HDMI cable.
• Video signals input to the HDMI IN jack can
only be output from the HDMI OUT jack.
The input video signals cannot be output
from the VIDEO OUT or MONITOR OUT
jacks.
• Refer to the operating instructions of each
connected component for details.
22US
Connecting a TV
Getting Started
The image from a visual component connected
to this receiver can be displayed on a TV
screen.
It is not necessary to connect all the cords.
Connect audio and video cords according to
the jacks of your components.
TV
Audio signals
Video signals
A
B
C
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
Y
AM
VIDEO 2/
BD IN
PB/CB
COAXIAL
DVD
IN
PR/CR
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
MONITOR
DMPORT
DVD IN
VIDEO 1 IN MONITOR OUT
COMPONENT VIDEO
R
L
L
L
L
L
L
L
AUDIO OUT
R
R
OUT
IN
SA-CD/CD/CD-R
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFER
FRONT B
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
A Audio cord (not supplied)
B Video cord (not supplied)
C Component video cord (not supplied)
Notes
Tips
• Connect image display components such as a TV
or a projector to the MONITOR OUT jack on the
receiver.
• Be sure to turn on the receiver when the video and
audio of a playback component are being output to
a TV via the receiver. If the power supply of the
receiver is not turned on, neither video nor audio is
transmitted.
• You can watch the selected input image when you
connect the MONITOR OUT jack to a TV.
• To output the sound of the TV from the speakers
connected to the receiver, be sure to
– connect the audio output jacks of the TV to the
TV IN jacks of the receiver.
– turn off or mute the TV’s volume.
23US
Note
Connecting a DVD player/DVD
recorder
To input multi channel digital audio from the DVD
player, set the digital audio output setting on the
DVD player. Refer to the operating instructions
supplied with the DVD player.
The following illustration shows how to
connect a DVD player and DVD recorder.
It is not necessary to connect all the cords.
Connect audio and video cords according to
the jacks of your components.
Tip
All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
Connecting a DVD player
DVD player
Audio signals
Video signals
A
C
B
D
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
Y
AM
VIDEO 2/
BD IN
PB/CB
COAXIAL
DVD
IN
PR/CR
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
SAT IN
MONITOR
DMPORT
DVD IN
VIDEO 1 IN MONITOR OUT
COMPONENT VIDEO
R
L
L
L
L
L
L
L
AUDIO OUT
R
R
OUT
IN
SA-CD/CD/CD-R
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFER
A Coaxial digital cord (supplied)
B Audio cord (not supplied)
C Video cord (not supplied)
D Component video cord (not supplied)
24US
FRONT B
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
Connecting a DVD recorder
Getting Started
DVD recorder
Audio signals
Video signals
A
B
C
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
Y
AM
VIDEO 2/
BD IN
PB/CB
COAXIAL
DVD
IN
PR/CR
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
MONITOR
DMPORT
SAT IN
DVD IN
VIDEO 1 IN MONITOR OUT
COMPONENT VIDEO
R
L
L
L
L
L
L
L
AUDIO OUT
R
R
OUT
IN
SA-CD/CD/CD-R
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFER
FRONT B
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
A Audio cord (not supplied)
B Video cord (not supplied)
C Component video cord (not supplied)
Notes
• Be sure to change the factory setting of the VIDEO
1 input button on the remote so that you can use the
button to control your DVD recorder. For details,
see “Programming the remote” (page 65).
• You can also rename the VIDEO 1 input so that it
can be displayed on the receiver’s display. For
details, see “Naming inputs” (page 63).
25US
Notes
Connecting a satellite tuner/
set-top box
• When connecting optical digital cords, insert the
plugs straight in until they click into place.
• Do not bend or tie optical digital cords.
The following illustration shows how to
connect a satellite tuner or set-top box.
It is not necessary to connect all the cords.
Connect audio and video cords according to
the jacks of your components.
Tip
All the digital audio jacks are compatible with
32 kHz, 44.1 kHz, 48 kHz, and 96 kHz sampling
frequencies.
Satellite tuner/Set-top box
Audio signals
A
Video signals
B
C
D
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
Y
AM
VIDEO 2/
BD IN
PB/CB
COAXIAL
DVD
IN
PR/CR
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
MONITOR
DMPORT
SAT IN
DVD IN
VIDEO 1 IN MONITOR OUT
COMPONENT VIDEO
R
L
L
L
L
L
L
L
AUDIO OUT
R
R
OUT
IN
SA-CD/CD/CD-R
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFER
A Audio cord (not supplied)
B Optical digital cord (not supplied)
C Video cord (not supplied)
D Component video cord (not supplied)
26US
FRONT B
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
Getting Started
Connecting components with
analog video and audio jack
The following illustration shows how to
connect a component which has analog jacks
such as a VCR, etc.
VCR
Audio signals
Video signals
A
B
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
Y
AM
VIDEO 2/
BD IN
PB/CB
COAXIAL
DVD
IN
PR/CR
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
MONITOR
DMPORT
SAT IN
DVD IN
VIDEO 1 IN MONITOR OUT
R
L
L
L
L
COMPONENT VIDEO
L
L
L
AUDIO OUT
R
R
OUT
IN
SA-CD/CD/CD-R
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFER
FRONT B
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
VIDEO 3 IN/PORTABLE AV IN
VIDEO
L AUDIO R
To the VIDEO 3 IN/PORTABLE AV IN jacks
(Front panel)
Camcorder/
video game
C
A Audio cord (not supplied)
B Video cord (not supplied)
C Audio/video cord (not supplied)
27US
4: Connecting the antennas
Connect the supplied AM loop antenna and
FM wire antenna.
FM wire antenna (supplied)
AM loop antenna (supplied)
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
Y
AM
VIDEO 2/
BD IN
PB/CB
COAXIAL
DVD
IN
PR/CR
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
MONITOR
DMPORT
SAT IN
DVD IN
VIDEO 1 IN MONITOR OUT
COMPONENT VIDEO
R
L
L
L
L
L
L
L
AUDIO OUT
R
R
OUT
IN
SA-CD/CD/CD-R
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFER
* The shape of the connector varies depending on
the area code of this receiver.
Notes
• To prevent noise pickup, keep the AM loop
antenna away from the receiver and other
components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as
horizontal as possible.
28US
FRONT B
R
FRONT A
SPEAKERS
R
SURROUND
CENTER
Connecting the AC power cord
Connect the AC power cord to a wall outlet.
AC power cord
Performing initial setup
operations
Before using the receiver for the first time,
initialize the receiver by performing the
following procedure. This procedure can also
be used to return settings you have made to
their factory defaults.
Be sure to use the buttons on the receiver for
this operation.
1,2
?/1
MASTER VOLUME
DISPLAY
INPUT MODE
INPUT SELECTOR
SPEAKERS
(OFF/A/B/A+B)
AUTO CAL MIC
MEMORY/
ENTER
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
MUTING
VIDEO 3 IN/PORTABLE AV IN
PHONES
L
VIDEO
R
SURROUND
L AUDIO R
3
CENTER
To the wall outlet
1
Press ?/1 to turn off the
receiver.
2
Hold down ?/1 for 5 seconds.
“PUSH” and “ENTER” appears on the
display alternately.
3
Press MEMORY/ENTER.
After “CLEARING” appears on the
display for a while, “CLEARED”
appears.
The following items are reset to their
factory settings.
• All settings in the LEVEL, TONE,
SUR, TUNER, AUDIO, VIDEO and
SYSTEM menus.
• The sound field memorized for each
input and preset station.
• All sound field parameters.
• All preset stations.
• All index names for inputs and preset
stations.
• MASTER VOLUME is set to “VOL
MIN”.
• Input is set to “DVD”.
29US
Getting Started
5: Preparing the receiver
and the remote
Inserting batteries into the
remote
Insert two R6 (size-AA) batteries in the
RM-AAP017 remote commander.
Observe the correct polarity when installing
batteries.
6: Selecting the speaker
system
You can select the front speakers you want to
drive.
Be sure to use the buttons on the receiver for
this operation.
SPEAKERS (OFF/A/B/A+B)
?/1
MASTER VOLUME
DISPLAY
INPUT MODE
INPUT SELECTOR
SPEAKERS
(OFF/A/B/A+B)
AUTO CAL MIC
MEMORY/
ENTER
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
MUTING
VIDEO 3 IN/PORTABLE AV IN
PHONES
VIDEO
Notes
• Do not leave the remote in an extremely hot or
humid place.
• Do not use a new battery with old ones.
• Do not mix alkaline batteries and other kinds of
batteries.
• Do not expose the remote sensor to direct sunlight
or lighting apparatuses. Doing so may cause a
malfunction.
• If you do not intend to use the remote for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage and
corrosion.
• When you replace the batteries, the programmed
remote codes may be cleared. If this happens,
program the remote codes again (page 65).
Tip
Under normal conditions, the batteries should last
for about 3 months. When the remote no longer
operates the receiver, replace all the batteries with
new ones.
30US
L AUDIO R
Press SPEAKERS (OFF/A/B/A+B)
repeatedly to select the front
speaker system you want to drive.
To select
Light up
The speakers connected to the
SPEAKERS FRONT A terminals
SP A
The speakers connected to the
SPEAKERS FRONT B terminals
SP B
The speakers connected to both the
SPEAKERS FRONT A and B
terminals (parallel connection)
SP A and
SP B
To turn off the speaker output
Press SPEAKERS (OFF/A/B/A+B)
repeatedly until the “SP A” and “SP B”
indicators on the display do not light up.
Note
You cannot switch the front speaker system by
pressing SPEAKERS (OFF/A/B/A+B) when the
headphones are connected.
Notes
?/1
(AUTO CALIBRATION)
MASTER VOLUME
DISPLAY
INPUT MODE
INPUT SELECTOR
Optimizer microphone
SPEAKERS
(OFF/A/B/A+B)
AUTO CAL MIC
MEMORY/
ENTER
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
MUTING
VIDEO 3 IN/PORTABLE AV IN
PHONES
VIDEO
L AUDIO R
This receiver is equipped with DCAC (Digital
Cinema Auto Calibration) Technology which
allows you to perform automatic calibration as
follows:
• Check the connection between each speaker
and the receiver.
• Adjust the speaker level.
• Measure the distance of each speaker to your
listening position.
You can also adjust the speaker levels and
balance manually. For details, see
“8: Adjusting the speaker levels and balance
(TEST TONE)” (page 34).
Before you perform Auto
Calibration
Before you perform Auto Calibration, install
and connect the speakers (page 15–17).
• The AUTO CAL MIC jack is used for the
supplied optimizer microphone only. Do not
connect other microphones to this jack.
Doing so may damage the receiver and the
microphone.
• During calibration, the sound that comes out
of the speakers is very loud. Pay attention to
the presence of children or to the effect on
your neighborhood.
• Perform Auto Calibration in a quiet
environment to avoid the effect of noise and
to get a more accurate measurement.
• If there are any obstacles in the path between
the optimizer microphone and the speakers,
the calibration cannot be performed
correctly. Remove any obstacles from the
measurement area to avoid measurement
error.
1
Connect the supplied optimizer
microphone to the AUTO CAL
MIC jack.
2
Set up the optimizer
microphone.
Place the optimizer microphone at your
listening position.You can also use a stool
or tripod so that the optimizer
microphone remains at the same height as
your ears.
31US
Getting Started
7: Calibrating the
appropriate settings
automatically
• The Auto Calibration function does not work when
headphones are connected.
• Make sure SPEAKERS (OFF/A/B/A+B) is not set
to off.
Performing Auto Calibration
The table below shows the display when
measurement starts.
Measurement for
?/1
TV RM SET UP AV ?/1
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3 DVD
SA-CD/CD TUNER
SAT
TV
AUX
DMPORT
?/1
switch
RECEIVER
2CH
A.F.D.
MOVIE
1
2
3
4
5
6
7
8
9
CLEAR
0/10
AUTO
CAL
V
B
v
RETURN/
EXIT
MENU
OPTIONS
TOOLS
.
REPLAY ADVANCE
<
<
>
MEASURE and
GAIN appears
alternately*
Speaker distance
MEASURE and
DISTANCE appears
alternately*
After you have finished
Disconnect the optimizer microphone from the
receiver.
TUNING +
TUNING –
H
Note
M
Auto Calibration cannot detect the sub woofer.
Therefore, all sub woofer settings will be
maintained.
DISC SKIP
X
TV VOL
MASTER VOL
MUTING
MUTING
x
TV CH
PRESET
MASTER
VOL +/–
DVD
Press AUTO CAL.
Measurement starts in 5 seconds and the
display changes as follows:
A.CAL [5] t A.CAL [4] t A.CAL [3] t
A.CAL [2] t A.CAL [1]
While the time is counting down, stand away
from the measurement area to avoid
measurement error.
32US
Speaker level
The measurement process will take a few
minutes to complete.
When measurement ends, “COMPLETE”
appears on the display and the settings are
registered.
ENTER
MEMORY
DISPLAY
m
MEASURE and SP
DET. appears
alternately*
* The corresponding speaker indicator lights up in
the display during measurement.
– /– –
B
NOISE.CHK
Speaker connection
MUSIC
SLEEP FM MODE D. TUNING AUTO CAL
>10
GUIDE
Environment noise level
Input
buttons
RECEIVER
Display
Tip
The Auto Calibration function will be canceled
when you do the following during the measurement
process:
– Press ?/1, input buttons or MUTING.
– Change the volume level.
– Press AUTO CAL again.
Error and warning codes
When an error is detected during Auto
Calibration, an error code will appear on the
display cyclically after each measurement
process as follows:
Error code t blank display t (error code t
blank display)a) t PUSH t blank display
t ENTER
a)
Appears when there are more than one error code.
To rectify the error
1 Record down the error code.
2 Press RECEIVER.
3
4
5
6
The RECEIVER indicator lights up and
receiver operation is activated.
Press .
Press ?/1 to turn off the receiver.
Rectify the error.
For details, see “Error codes and remedies”
below.
Turn on the receiver and perform Auto
Calibration again (page 32).
Explanation
Remedy
ERROR 10 The environment Make sure the
is too noisy.
environment is
quiet during Auto
Calibration.
ERROR 11 The speakers are
placed too near
the optimizer
microphone.
Place your speakers
further away from
the optimizer
microphone.
ERROR 12 None of the
speakers are
detected.
Make sure that the
optimizer
microphone is
connected properly
and perform Auto
Calibration again.
Remedy
ERROR 21 Only one
Check the surround
surround speaker speakers
is detected.
connection.
Warning codes
During Auto Calibration, the warning code
provides information on the measurement
result. The warning code will appear on the
display cyclically as follows:
Warning code t blank display t (warning
code t blank display)b) t PUSH t blank
display t ENTER
b) Appears
when there are more than one warning
code.
You can choose to ignore the warning code as
the Auto Calibration function will
automatically adjust the settings. You can also
change the settings manually.
To change the settings
manually
1 Record down the warning code.
2 Press RECEIVER.
Error codes and remedies
Error
code
Explanation
3
4
5
6
The RECEIVER indicator lights up and
receiver operation is activated.
Press .
Press ?/1 to turn off the receiver.
Follow the solution provided in the
“Warning codes and solutions” below.
Turn on the receiver and perform Auto
Calibration again (page 32).
ERROR 20 Front speakers
Check the front
are not detected speakers
or only one front connection.
speaker is
detected.
continued
33US
Getting Started
Error codes
Error
code
Warning codes and solutions
Warning
code
Explanation
Solution
WARN. 40 The environment Make sure the
is noisy.
environment is
quiet during Auto
Calibration.
8: Adjusting the speaker
levels and balance
(TEST TONE)
WARN. 50 The center speaker Be sure to connect
is not connected. the center speaker.
You can adjust the speaker levels and balance
while listening to the test tone from your
listening position.
WARN. 51 The surround
speakers are not
connected.
Tip
Be sure to connect
the surround
speakers.
WARN. 60 The front speaker Reposition your
balance is out of front speakers.c)
range.
WARN. 62 The center speaker Reposition your
level is out of
center speaker.d)
range.
WARN. 63 The surround left Reposition your
speaker level is out surround left
of range.
speaker.e)
The receiver employs a test tone with a frequency
centered at 800 Hz.
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3 DVD
Input
buttons
WARN. 64 The surround right Reposition your
speaker level is out surround right
of range.
speaker.f)
TV
DMPORT
2CH
A.F.D.
1
MUSIC
1
2
3
4
5
6
7
8
9
CLEAR
0/10
>10
GUIDE
ENTER
MEMORY
DISPLAY
V
3-6
B
B
v
RETURN/
EXIT
MENU
.
REPLAY ADVANCE
<
<
OPTIONS
TOOLS
>
TUNING +
TUNING –
H
m
M
DISC SKIP
X
TV VOL
MASTER VOL
MASTER
VOL +/–
MUTING
DVD
34US
MOVIE
– /– –
c)
For details, refer “Front speakers distance”
(page 47).
d) For details, refer “Center speaker distance”
(page 47).
e)
For details, refer “Surround left speaker distance”
(page 47).
f)
For details, refer “Surround right speaker
distance” (page 47).
RECEIVER
SLEEP FM MODE D. TUNING AUTO CAL
WARN. 72 The center speaker Reposition your
distance is out of center speaker.d)
range.
WARN. 74 The surround right Reposition your
speaker distance is surround right
out of range.
speaker.f)
SA-CD/CD TUNER
SAT
AUX
WARN. 70 The front speaker Reposition your
distance is out of front speakers.c)
range.
WARN. 73 The surround left Reposition your
speaker distance is surround left
out of range.
speaker.e)
?/1
TV RM SET UP AV ?/1
x
TV CH
PRESET
2
1
Press RECEIVER.
2
Press MENU.
“1-LEVEL” appears on the display.
3
Press
menu.
4
Press V/v repeatedly to select
“T. TONE”.
5
Press
or b to enter the
parameter.
6
Press V/v repeatedly to select
“T. TONE Y”.
When a test tone is not output
from the speakers
• The speaker cords may not be connected
securely.
• The speaker cords may have the short-circuit
problem.
or b to enter the
The test tone is output from each speaker
in sequence as follows:
Front left t Center t Front right t
Surround right t Surround left t Sub
woofer
7
Adjust the speaker levels and
balance using the LEVEL menu
so that the level of the test tone
sounds the same from each
speaker.
For details, see “Adjusting the level
(LEVEL menu)” (page 43).
Tips
• To adjust the level of all speakers at the same
time, press MASTER VOL +/–. You can also
use MASTER VOLUME on the receiver.
• The adjusted value are shown on the display
during adjustment.
8
Repeat steps 1 to 6 to select
“T. TONE N”.
You can also press any input buttons.
The test tone turns off.
35US
Getting Started
The RECEIVER indicator lights up and
receiver operation is activated.
Selected input Components that can
[Display]
be played back
Playback
VIDEO 1
[VIDEO 1]
Selecting a component
VIDEO 2
Blu-ray disc player, etc.,
[VIDEO 2/BD]* connected to the VIDEO
2/BD jack
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3 DVD
SAT
TV
SA-CD/CD TUNER
AUX
DMPORT
2CH
A.F.D.
1
RECEIVER
MOVIE
MUSIC
SLEEP FM MODE D. TUNING AUTO CAL
1
2
3
4
5
6
7
8
9
CLEAR
0/10
ENTER
– /– –
>10
GUIDE
MEMORY
DISPLAY
VIDEO 3
[VIDEO 3/
PORTABLE
AV]*
Camcorder, video game,
etc., connected to the
VIDEO 3 IN/PORTABLE
AV IN jack
DVD
[DVD]
DVD player, etc.,
connected to DVD jack
SAT
[SAT]
Satellite tuner, set-top box,
etc., connected to SAT jack
TV
[TV]
TV, etc., connected to TV
jack
SA-CD/CD
[SA-CD/CD/
CD-R]*
Super Audio CD player,
CD player, etc., connected
to the SA-CD/CD/CD-R
jack
V
B
TUNER
Built-in radio tuner
[FM or AM band]
B
v
RETURN/
EXIT
MENU
.
REPLAY ADVANCE
<
<
* “VIDEO 2/BD”, “VIDEO 3/PORTABLE
AV” and “SA-CD/CD/CD-R” scroll across
the display, then “VIDEO 2”, “VIDEO 3”
and “SA-CD/CD” appear respectively.
M
DISC SKIP
X
TV VOL
MASTER VOL
MUTING
MUTING
x
TV CH
PRESET
3
DVD
1
Press one of the input buttons
to select the component you
want.
You can also use INPUT SELECTOR on
the receiver.
The selected input appears on the display.
36US
DIGITAL MEDIA PORT
adapter connected to
DMPORT jack
>
H
m
DMPORT
[DMPORT]
OPTIONS
TOOLS
TUNING +
TUNING –
VCR, etc., connected to the
VIDEO 1 jack
2
Turn on the component and
start playback.
3
Press MASTER VOL +/– to
adjust the volume.
You can also use MASTER VOLUME on
the receiver.
To mute the sound
Press MUTING.
The muting function will be canceled when
you do the following.
• Press MUTING again.
• Increase the volume.
• Turn off the receiver.
To avoid damaging your
speakers
Before you turn off the receiver, be sure to turn
down the volume level.
To listen to the sub woofer
Playback
Be sure to use the buttons on the sub woofer
for this operation.
1 Press POWER.
The POWER indicator lights up.
2 Turn LEVEL to adjust the volume.
Set the volume level to suit your preference
according to the selected input as slight
adjustments may enhance the sound.
Note
Do not set the volume of the sub woofer to
maximum as extraneous noise may be heard.
37US
Listening/Watching a component
Listening to a Super Audio CD/CD
?/1
TV RM SET UP AV ?/1
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3 DVD
SA-CD/CD TUNER
SAT
TV
AUX
DMPORT
2CH
A.F.D.
RECEIVER
MOVIE
2
3
MUSIC
?/1
MASTER VOLUME
SLEEP FM MODE D. TUNING AUTO CAL
DISPLAY
1
2
3
4
5
6
7
8
9
CLEAR
0/10
ENTER
INPUT MODE
5
INPUT SELECTOR
SPEAKERS
(OFF/A/B/A+B)
AUTO CAL MIC
– /– –
>10
GUIDE
MEMORY/
ENTER
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
VIDEO 3 IN/PORTABLE AV IN
MEMORY
DISPLAY
PHONES
V
VIDEO
B
L AUDIO R
AUTO CAL
MUTING
3
B
v
RETURN/
EXIT
MENU
.
REPLAY ADVANCE
<
<
m
OPTIONS
TOOLS
>
TUNING +
TUNING –
H
M
DISC SKIP
X
TV VOL
MASTER VOL
x
TV CH
PRESET
5
MUTING
DVD
TOP MENU MENU
F1
F2
TV INPUT
WIDE
Notes
• The operation is described for a
Sony Super Audio CD player.
• Refer to the operating
instructions supplied with the
Super Audio CD player or CD
player.
1
Turn on the Super Audio CD player or CD
player, then place the disc on the tray.
2
3
Turn on the receiver.
You can also use INPUT SELECTOR on the receiver to
select “SA-CD/CD/CD-R”.
Tips
• You can select the sound field to
suit the music. Refer to page 51
for details.
Recommended sound fields:
Classical: HALL
Jazz: JAZZ
Live concert: CONCERT
• You can listen to the sound that
was recorded in the 2 channel
format from all speakers (multi
channel). Refer to page 49 for
details.
38US
Press SA-CD/CD.
4
5
6
Play back the disc.
Adjust to a suitable volume.
After you have finished listening to the
Super Audio CD/CD, eject the disc and turn
off the receiver and Super Audio CD player
or CD player.
Watching a DVD
?/1
TV RM SET UP AV ?/1
SYSTEM STANDBY
VIDEO 1 VIDEO 2 VIDEO 3 DVD
SA-CD/CD TUNER
SAT
TV
AUX
DMPORT
2CH
A.F.D.
RECEIVER
MOVIE
MUSIC
?/1
MASTER VOLUME
SLEEP FM MODE D. TUNING AUTO CAL
DISPLAY
1
2
INPUT MODE
3
7
INPUT SELECTOR
4
5
6
7
8
9
SPEAKERS
(OFF/A/B/A+B)
– /– –
AUTO CAL MIC
CLEAR
0/10
MEMORY/
ENTER
ENTER
>10
GUIDE
MEMORY
DISPLAY
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
VIDEO 3 IN/PORTABLE AV IN
PHONES
V
VIDEO
B
L AUDIO R
B
MUTING
3
v
RETURN/
EXIT
MENU
.
REPLAY ADVANCE
<
<
TUNING –
m
OPTIONS
TOOLS
>
TUNING +
H
M
DISC SKIP
X
TV VOL
MASTER VOL
x
TV CH
PRESET
7
MUTING
DVD
TOP MENU MENU
F1
F2
TV INPUT
WIDE
Notes
• Refer to the operating
instructions supplied with the
TV and DVD player.
• Check the following if you
cannot listen to multi channel
sound.
– Be sure the audio source
corresponds to the multi
channel format.
– Be sure this receiver is
connected to the DVD player
via a digital connection.
– Be sure the digital audio
output of the DVD player is
set up properly.
Tips
• Select the audio format of the
disc to be played, if necessary.
• You can select the sound field to
suit the movie or music. Refer to
page 51 for details.
Recommended sound fields:
Movie: C.ST.EX
Music: CONCERT
1
2
3
Turn on the TV and DVD player.
Turn on the receiver.
Press DVD.
You can also use INPUT SELECTOR on the receiver to
select “DVD”.
4
Switch the input of the TV so that an image
of the DVD is displayed.
5
Set up the DVD player.
Refer to “Quick Setup Guide” supplied with the receiver.
6
7
8
Play back the disc.
Adjust to a suitable volume.
After you have finished watching the DVD,
eject the disc and turn off the receiver, TV
and DVD player.
39US
Playback
2
3
Amplifier Operations
Navigating through
menus
TV
AUX
DMPORT
2CH
A.F.D.
Press
or b to enter the
parameter.
7
Press V/v repeatedly to select
the setting you want.
The setting is entered automatically.
By using the amplifier menus, you can make
various adjustments to customize the receiver.
SAT
6
8
Repeat steps 3 to 7 when you
want to make other settings.
SA-CD/CD TUNER
RECEIVER
MOVIE
1
MUSIC
To return to the previous
display
Press B.
SLEEP FM MODE D. TUNING AUTO CAL
To exit the menu
1
2
3
4
5
6
7
8
9
CLEAR
0/10
ENTER
Press MENU.
However, if the RECEIVER indicator is light
off, press RECEIVER and then press MENU.
Note
– /– –
>10
GUIDE
Some parameters and settings may appear dimmed
on the display. This means that they are either
unavailable or fixed and unchangeable.
MEMORY
DISPLAY
V
3-7
B
B
v
1
RETURN/
EXIT
MENU
OPTIONS
TOOLS
.
REPLAY ADVANCE
<
<
>
2
Press RECEIVER.
The RECEIVER indicator lights up and
receiver operation is activated.
2
Press MENU.
“1-LEVEL” appears on the display.
3
Press V/v repeatedly to select
the menu you want.
4
Press
menu.
5
Press V/v repeatedly to select
the parameter you want to
adjust.
40US
or b to enter the
Overview of the menus
The following options are available in each
menu. For details on navigating through
menus, see page 40.
Parameters
[Display]
LEVEL
[1-LEVEL]
(page 43)
Test tonea) [T. TONE]
a)
Settings
Initial
setting
T. TONE Y, T. TONE N
T. TONE N
Front speaker balance
[FRT BAL]
BAL. L +1 to BAL. L +8, BALANCE, BALANCE
BAL. R +1 to BAL. R +8
Center speaker level
[CNT LVL]
CNT –10 dB to CNT +10 dB
(1 dB step)
CNT 0 dB
Surround left speaker level
[SL LVL]
SUR L –10 dB to SUR L +10 dB
(1 dB step)
SUR L 0 dB
Surround right speaker level
[SR LVL]
SUR R –10 dB to SUR R +10 dB
(1 dB step)
SUR R 0 dB
Sub woofer level
[SW LVL]
SW –10 dB to SW +10 dB
(1 dB step)
SW 0 dB
Dynamic range compressora)
[D. RANGE]
COMP. OFF, COMP. STD,
COMP. MAX
COMP. OFF
TONE
[2-TONE]
(page 44)
Front speakers bass level
[BASS LVL]
BASS –6 dB to BASS +6 dB
(1 dB step)
BASS 0 dB
Front speakers treble level
[TRE LVL]
TRE –6 dB to TRE +6 dB
(1 dB step)
TRE 0 dB
SUR
[3-SUR]
(page 44)
Sound field selectiona)
[S.F. SELCT]
2CH ST., A.F.D. AUTO, DOLBY PL, A.F.D. AUTO
PLII MV, PLII MS, MULTI ST.,
C.ST.EX A, C.ST.EX B, C.ST.EX C,
PORTABLE, HALL, JAZZ,
CONCERT
Effect levela) [EFFECT]
EFCT. MIN, EFCT. STD,
EFCT. MAX
EFCT. STD
FM station receiving modea)
[FM MODE]
FM AUTO, FM MONO
FM AUTO
TUNER
[4-TUNER]
(page 45)
Naming preset stationsa)
[NAME IN]
continued
41US
Amplifier Operations
Menu
[Display]
Menu
[Display]
Parameters
[Display]
Settings
Initial
setting
AUDIO
[5-AUDIO]
(page 45)
Digital audio input decoding
prioritya) [DEC. PRI.]
DEC. AUTO, DEC. PCM
DEC. AUTO
for:
VIDEO 2, SAT;
DEC. PCM for:
DVD
Digital broadcast language
selectiona) [DUAL]
DUAL M/S, DUAL M, DUAL S,
DUAL M+S
DUAL M
Synchronizes audio with video
outputa) [A.V. SYNC.]
A.V.SYNC. Y, A.V.SYNC. N
A.V.SYNC. N
Naming inputsa) [NAME IN]
VIDEO
[6-VIDEO]
(page 46)
DIGITAL MEDIA PORT video –NONE, –VIDEO 1, –VIDEO 3,
–DVD, –SAT
assigna)
[DMPORT V.]
–NONE
Naming inputsa) [NAME IN]
SYSTEM
[7-SYSTEM]
(page 47)
A. CAL
[8-A. CAL]
(page 49)
a)
Front speakers distancea)
[FRT DIST.]
DIST. 3 ft. to DIST. 23 ft.
(1 foot step)
DIST. 10 ft.
Center speaker distancea)
[CNT DIST.]
DIST. xx ft.
between front speaker distance and
5 feet (1 foot step)
DIST. 10 ft.
Surround left speaker distancea) DIST. xx ft.
[SL DIST.]
between front speaker distance and
15 feet (1 foot step)
DIST. 10 ft.
Surround right speaker
distancea)
[SR DIST.]
DIST. xx ft.
between front speaker distance and
15 feet (1 foot step)
DIST. 10 ft.
Surround speaker positiona)
[SUR POS.]
SIDE/LO, SIDE/HI, BEHD/LO,
BEHD/HI
SIDE/LO
Brightness of the displaya)
[DIMMER]
0% dim, 40% dim, 70% dim
0% dim
Auto Calibrationa)
[AUTO CAL]
A.CAL YES, A.CAL NO
A.CAL NO
For details, refer to the page in the parentheses.
42US
Adjusting the level
(LEVEL menu)
LEVEL menu parameters
Lets you compress the dynamic range of the
sound track. This may be useful when you
want to watch movies at low volumes late at
night. Dynamic range compression is possible
with Dolby Digital sources only.
• COMP. OFF
The dynamic range is not compressed.
• COMP. STD
The dynamic range is compressed as
intended by the recording engineer.
• COMP. MAX
The dynamic range is compressed
dramatically.
x T. TONE (Test tone)
Tip
Lets you adjust the speaker levels and balance
while listening to the test tone from your
listening position. For details, see “8:
Adjusting the speaker levels and balance
(TEST TONE)” (page 34).
Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the
dynamic range information included in the Dolby
Digital signal.
“COMP. STD” is the standard setting, but it only
enacts light compression. Therefore, we recommend
using the “COMP. MAX” setting. This greatly
compresses the dynamic range and lets you view
movies late at night at low volumes. Unlike analog
limiters, the levels are predetermined and provide a
very natural compression.
x FRT BAL (Front speaker
balance)
Lets you adjust the balance between front left
and right speakers.
x CNT LVL (Center speaker level)
x SL LVL (Surround left speaker
level)
x SR LVL (Surround right speaker
level)
x SW LVL (Sub woofer level)
43US
Amplifier Operations
You can use the LEVEL menu to adjust the
balance and level of each speaker. These
settings are applied to all sound fields.
Select “1-LEVEL” in the amplifier menus. For
details on adjusting the parameters, see
“Navigating through menus” (page 40) and
“Overview of the menus” (page 41).
x D. RANGE (Dynamic range
compressor)
Adjusting the tone
(TONE menu)
You can use the TONE menu to adjust the
tonal quality (bass/treble level) of the front
speakers.
Select “2-TONE” in the amplifier menus. For
details on adjusting the parameters, see
“Navigating through menus” (page 40) and
“Overview of the menus” (page 41).
TONE menu parameters
x BASS LVL (Front speakers bass
level)
x TRE LVL (Front speakers treble
level)
Settings for the surround
sound
(SUR menu)
You can use the SUR menu to select the sound
field you want for your listening pleasure.
Select “3-SUR” in the amplifier menus. For
details on adjusting the parameters, see
“Navigating through menus” (page 40) and
“Overview of the menus” (page 41).
SUR menu parameters
x S.F. SELCT (Sound field
selection)
Lets you select the sound field you want. For
details, see “Enjoying Surround Sound” (page
49).
Note
The receiver lets you apply the last selected sound
field to an input whenever it is selected (Sound Field
Link). For example, if you select “HALL” for the
SA-CD/CD input, then change to a different input
and then return to SA-CD/CD, “HALL” will
automatically be applied again.
x EFFECT (Effect level)
Lets you adjust the “presence” of the surround
effect for sound fields selected with the
MOVIE or MUSIC button and for “HP
THEA” sound field. However, the surround
effect is not available for “PORTABLE”
sound field.
• EFCT. MIN
The surround effect is minimum.
• EFCT. STD
The surround effect is standard.
• EFCT. MAX
The surround effect is maximum.
44US
Settings for the audio
(TUNER menu)
(AUDIO menu)
You can use the TUNER menu to set the FM
station receiving mode and to name preset
stations.
Select “4-TUNER” in the amplifier menus.
For details on adjusting the parameters, see
“Navigating through menus” (page 40) and
“Overview of the menus” (page 41).
You can use the AUDIO menu to make
settings for the audio to suit your preference.
Select “5-AUDIO” in the amplifier menus. For
details on adjusting the parameters, see
“Navigating through menus” (page 40) and
“Overview of the menus” (page 41).
AUDIO menu parameters
TUNER menu parameters
x FM MODE (FM station receiving
mode)
• FM AUTO
This receiver will decode the signal as stereo
signal when the radio station is broadcast in
stereo.
• FM MONO
This receiver will decode the signal as mono
signal regardless of the broadcast signal.
x NAME IN (Naming preset
stations)
Lets you set the name of preset stations. For
details, see “Naming preset stations” (page
58).
x DEC. PRI. (Digital audio input
decoding priority)
Lets you specify the input mode for the digital
signal input to the DIGITAL IN jacks.
• DEC. AUTO
Automatically switches the input mode
between DTS, Dolby Digital, or PCM.
• DEC. PCM
PCM signals are given priority (to prevent
interruption when playback starts).
However, when other signals are input, there
may be no sound depending on the format.
In this case, set to “DEC. AUTO”.
Note
When set to “DEC. AUTO” and the sound from the
digital audio jacks (for a CD, etc.) is interrupted
when playback starts, set to “DEC. PCM”.
continued
45US
Amplifier Operations
Settings for the tuner
x DUAL (Digital broadcast
language selection)
Lets you select the language you want to listen
to during digital broadcast. This feature only
functions for Dolby Digital sources.
• DUAL M/S (Main/Sub)
Sound of the main language will be output
through the front left speaker and sound of
the sub language will be output through the
front right speaker simultaneously.
• DUAL M (Main)
Sound of the main language will be output.
• DUAL S (Sub)
Sound of the sub language will be output.
• DUAL M+S (Main + Sub)
Mixed sound of both the main and sub
languages will be output.
x A.V. SYNC. (Synchronizes audio
with video output)
• A.V.SYNC. Y (Yes) (Delay time: 68 ms)
The audio output is delayed so that the time
gap between the audio output and visual
display is minimized.
• A.V.SYNC. N (No) (Delay time: 0 ms)
The audio output is not delayed.
Notes
• This parameter is useful when you use a large LCD
or plasma monitor or a projector.
• This parameter is valid only when you use a sound
field selected with the 2CH or A.F.D. button.
• This parameter is not valid when PCM 96 kHz or
DTS 2048 signals are input.
x NAME IN (Naming inputs)
Lets you set the name of inputs. For details,
see “Naming inputs” (page 63).
46US
Settings for the video
(VIDEO menu)
You can use the VIDEO menu to assign the
composite video input to DMPORT input and
to name inputs.
Select “6-VIDEO” in the amplifier menus. For
details on adjusting the parameters, see
“Navigating through menus” (page 40) and
“Overview of the menus” (page 41).
VIDEO menu parameters
x DMPORT V. (DIGITAL MEDIA
PORT video assign)
Lets you assign the composite video input to
DMPORT input so that you can view the
images on the TV screen. For details, see
“Watching a connected component through
DMPORT connection” (page 62).
x NAME IN (Naming inputs)
Lets you set the name of inputs. For details,
see “Naming inputs” (page 63).
Settings for the system
(SYSTEM menu)
SYSTEM menu parameters
x FRT DIST. (Front speakers
distance)
Lets you set the distance from your listening
position to the front speaker (A). If both front
speakers are not placed an equal distance from
your listening position, set the distance as the
average distance between the front speakers.
B
A
30˚
100˚-120˚
C
30˚
A
100˚-120˚
D
x CNT DIST. (Center speaker
distance)
Lets you set the distance from your listening
position to the surround right speaker.
Surround right speaker distance should be set
from a distance equal to the front speaker
distance (A) to a distance 15 feet closer to
your listening position (D).
Tip
The receiver lets you to input the speaker position in
terms of distance. However, it is not possible to set
the center speaker further than the front speakers.
Also, the center speaker cannot be set more than
5 feet closer from the front speakers.
Likewise, the surround speakers can not be set
further away from the listening position than the
front speakers. And they can be no more than 15 feet
closer. This is because incorrect speaker placement
is not conducive to the enjoyment of surround
sound.
Please note that, setting the speaker distance closer
than the actual location of the speakers will cause a
delay in the output of the sound from that speaker. In
other words, the speaker will sound like it is further
away.
For example, setting the center speaker distance 3-6
feet closer than the actual speaker position will
create a fairly realistic sensation of being “inside”
the screen. If you cannot obtain a satisfactory
surround effect because the surround speakers are
too close, setting the surround speaker distance
closer (shorter) than the actual distance will create a
larger sound stage.
Adjusting these parameter while listening to the
sound often results in much better surround sound.
Give it a try!
Lets you set the distance from your listening
position to the center speaker. Center speaker
distance should be set from a distance equal to
the front speaker distance (A) to a distance
5 feet closer to your listening position (B).
x SL DIST. (Surround left speaker
distance)
Lets you set the distance from your listening
position to the surround left speaker. Surround
left speaker distance should be set from a
distance equal to the front speaker distance
(A) to a distance 15 feet closer to your
listening position (C).
continued
47US
Amplifier Operations
You can use the SYSTEM menu to set the
distance of the speakers connected to this
receiver.
Select “7-SYSTEM” in the amplifier menus.
For details on adjusting the parameters, see
“Navigating through menus” (page 40) and
“Overview of the menus” (page 41).
x SR DIST. (Surround right
speaker distance)
x SUR POS.
(Surround speaker position)
Lets you specify the location of your surround
speakers for proper implementation of the
surround effects in the CINEMA STUDIO EX
modes (page 52).
Tip
Surround speaker position is designed specifically
for implementation of the CINEMA STUDIO EX
modes. For other sound fields, speaker position is
not so critical.
Those sound fields were designed under the premise
that the surround speakers would be located behind
the listening position, but presentation remains
fairly consistent even with the surround speakers
positioned at a rather wide angle. However, if the
speakers are pointing toward the listener from the
immediate left and right of the listening position, the
surround effects become unclear unless set to
“SIDE/LO” or “SIDE/HI”.
Nevertheless, each listening environment has many
variables, such as wall reflections, and you may
obtain better results using “BEHD/HI” if your
speakers are located high above the listening
position, even if they are located to the immediate
left and right.
Therefore, although it may result in a setting
contrary to the above explanation, we recommend
that you play back multi channel surround encoded
software and select the setting that provides a good
sense of spaciousness and that best succeeds in
forming a cohesive space between the surround
sound from the surround speakers and the sound of
the front speakers. If you are not sure which sounds
best, select “BEHD/LO” or “BEHD/HI” and then
use the speaker distance parameter and speaker level
adjustments to obtain proper balance.
x DIMMER (Brightness of the
display)
Lets you adjust the brightness in 3 steps.
• SIDE/LO
Select if the location of your surround
speakers corresponds to sections A and C.
• SIDE/HI
Select if the location of your surround
speakers corresponds to sections A and D.
• BEHD/LO
Select if the location of your surround
speakers corresponds to sections B and C.
• BEHD/HI
Select if the location of your surround
speakers corresponds to sections B and D.
48US
Calibrating the
appropriate settings
automatically
(A. CAL menu)
For details, see “7: Calibrating the appropriate
settings automatically (AUTO
CALIBRATION)” (page 31).
Enjoying Surround Sound
Enjoying Dolby Digital
and DTS surround sound
(AUTO FORMAT DIRECT)
The Auto Format Direct (A.F.D.) mode allows
you to listen to higher fidelity sound and select
the decoding mode for listening to a 2 channel
stereo sound as multi channel sound.
TV
AUX
DMPORT
2CH
A.F.D.
SA-CD/CD TUNER
RECEIVER
MOVIE
MUSIC
SLEEP FM MODE D. TUNING AUTO CAL
Press A.F.D. repeatedly to select
the sound field you want.
For details, see “Types of A.F.D. mode” (page
50).
continued
49US
Enjoying Surround Sound
A.F.D.
SAT
Types of A.F.D. mode
Decoding
mode
A.F.D. mode
[Display]
Multi channel
audio after
decoding
Effect
(Detecting
automatically)
A.F.D. AUTO
[A.F.D. AUTO]
(Detecting
automatically)
Presents the sound as it was recorded/
encoded without adding any surround
effects. However, this receiver will
generate a low frequency signal for output
to the sub woofer when there is no LFE
signals.
4 channel
Performs Dolby Pro Logic decoding. The
source recorded in 2 channel format is
decoded into 4.1 channel.
Dolby Pro Logic PRO LOGIC
[DOLBY PL]
Dolby Pro Logic PRO LOGIC II MOVIE 5 channel
II
[PLII MV]
(Multi Stereo)
PRO LOGIC II MUSIC
[PLII MS]
5 channel
Performs Dolby Pro Logic II Music mode
decoding. This setting is ideal for normal
stereo sources such as CDs.
MULTI STEREO
[MULTI ST.]
(Multi Stereo)
Outputs 2 channel left/right signals from
all speakers.
Note
This function does not work for signals with a
sampling frequency of more than 48 kHz.
50US
Performs Dolby Pro Logic II Movie mode
decoding. This setting is ideal for movies
encoded in Dolby Surround. In addition,
this mode can reproduce sound in 5.1
channel for watching videos of overdubbed
or old movies.
Selecting a preprogrammed sound field
You can take advantage of surround sound
simply by selecting one of the receiver’s preprogrammed sound fields. They bring the
exciting and powerful sound of movie theaters
and concert halls into your home.
TV
DMPORT
SA-CD/CD TUNER
2CH
A.F.D.
RECEIVER
MOVIE
Enjoying Surround Sound
SAT
AUX
MUSIC
2CH
MUSIC
SLEEP FM MODE D. TUNING AUTO CAL
A.F.D.
MOVIE
1
2
3
Press MOVIE repeatedly to select a
sound field for movies or press
MUSIC repeatedly to select a sound
field for music.
For details, see “Types of sound field
available” (page 52).
continued
51US
Types of sound field available
Sound field
for
Sound field
[Display]
Effect
Movie
CINEMA STUDIO EX A
DCS [C.ST.EX A]
Reproduces the sound characteristics of the Sony Pictures
Entertainment “Cary Grant Theater” cinema production
studio. This is a standard mode, great for watching almost any
type of movie.
CINEMA STUDIO EX B
DCS [C.ST.EX B]
Reproduces the sound characteristics of the Sony Pictures
Entertainment “Kim Novak Theater” cinema production
studio. This mode is ideal for watching science-fiction or
action movies with lots of sound effects.
CINEMA STUDIO EX C
DCS [C.ST.EX C]
Reproduces the sound characteristics of the Sony Pictures
Entertainment scoring stage. This mode is ideal for watching
musicals or films where orchestra music is featured in the
soundtrack.
PORTABLE AUDIO
[PORTABLE]
Reproduces a clear enhanced sound image from your portable
audio device. This mode is ideal for MP3 and other
compressed music.
HALL [HALL]
Reproduces the acoustics of a classical concert hall.
JAZZ CLUB [JAZZ]
Reproduces the acoustics of a jazz club.
LIVE CONCERT
[CONCERT]
Reproduces the acoustics of a 300-seat live house.
HEADPHONE 2CH
[HP 2CH]
This mode is selected automatically if you use headphones
when 2CH STEREO mode (page 54)/A.F.D. mode (page 50)
is selected. Standard 2 channel stereo sources completely
bypass the sound field processing and multi channel surround
formats are downmixed to 2 channels.
HEADPHONE THEATER
DCS [HP THEA]
This mode is selected automatically if you use headphones
when sound field for movie/music is selected. It allows you to
experience a theater-like environment while listening through
a pair of headphones.
Music
Headphone*
* You can only select this sound field if the headphones are connected to the receiver.
52US
About DCS (Digital Cinema
Sound)
Sound fields with DCS mark use DCS
technology.
DCS is a unique sound reproduction
technology for home theater developed by
Sony, in cooperation with Sony Pictures
Entertainment, for enjoying the exciting and
powerful sound of movie theaters at home.
With this “Digital Cinema Sound” developed
by integrating a DSP (Digital signal processor)
and measured data, the ideal sound field
intended by film makers can be experienced at
home.
Tip
You can identify the encoding format of DVD
software, etc., by looking at the logo on the package.
•
: Dolby Digital discs
•
: Dolby Surround
encoded programs
•
: DTS Digital Surround encoded
programs
To turn off the surround effect
for movie/music
Press 2CH to select “2CH ST.” or press A.F.D.
repeatedly to select “A.F.D. AUTO”.
Enjoying Surround Sound
About CINEMA STUDIO EX
modes
CINEMA STUDIO EX modes are suitable for
watching motion picture DVDs (etc.), with
multi channel surround effects. You can
reproduce the sound characteristics of Sony
Pictures Entertainment’s dubbing studio in
your home.
The CINEMA STUDIO EX modes consist of
the following three elements.
• Virtual Multi Dimension
Creates 5 sets of virtual speakers from a
single pair of actual surround speakers.
• Screen Depth Matching
Creates the sensation that the sound is
coming from inside the screen like in
theaters.
• Cinema Studio Reverberation
Reproduces the type of reverberation found
in theaters.
The CINEMA STUDIO EX modes integrate
these three elements simultaneously.
Notes
• The effects provided by the virtual speakers may
cause increased noise in the playback signal.
• When listening with sound fields that employ the
virtual speakers, you will not be able to hear any
sound coming directly from the surround speakers.
• This function does not work for signals with a
sampling frequency of more than 48 kHz.
53US
Using only the front
speakers and sub woofer
(2CH STEREO)
In this mode, the receiver outputs the sound
from the front left/right speakers and the sub
woofer.
When multi channel surround formats are
input, the signals are downmixed to 2 channel
with bass frequencies being output from the
sub woofer.
When standard 2 channel stereo sources are
input, the receiver’s bass redirection circuitry
will be activated. The front channel bass
frequencies will be output from the sub
woofer.
2CH
SAT
TV
AUX
DMPORT
2CH
A.F.D.
54US
Be sure to use the buttons on the receiver for
this operation.
1,2
?/1
MASTER VOLUME
DISPLAY
RECEIVER
MOVIE
MUSIC
INPUT MODE
INPUT SELECTOR
SPEAKERS
(OFF/A/B/A+B)
AUTO CAL MIC
MEMORY/
ENTER
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
AUTO CAL
MUTING
VIDEO 3 IN/PORTABLE AV IN
PHONES
VIDEO
L AUDIO R
2
1
Press ?/1 to turn off the
receiver.
2
While holding down 2CH, press
?/1.
SA-CD/CD TUNER
SLEEP FM MODE D. TUNING AUTO CAL
Press 2CH.
Resetting sound fields to
the initial settings
“S.F. CLR.” appears on the display and
all sound fields are reset to their initial
setting.
Tuner Operations
Listening to FM/AM radio
You can listen to FM and AM broadcasts
through the built-in tuner. Before operation,
make sure you have connected the FM and
AM antennas to the receiver (page 28).
Tip
The tuning scale for direct tuning differs depending
on the area code as shown in the following table. For
details on area codes, see page 3.
1
Press TUNER repeatedly to
select the FM or AM band.
2
Press TUNING + or TUNING –.
Press TUNING + to scan from low to
high; press TUNING – to scan from high
to low.
The receiver stops scanning whenever a
station is received.
Using the controls on the
receiver
1 Turn INPUT SELECTOR to select the FM
or AM band.
Area code
FM
AM
U, CA
100 kHz
10 kHz*
2 Press TUNING MODE repeatedly to select
“AUTO T.”.
3 Press TUNING + or TUNING –.
In case of poor FM stereo
reception
Automatic tuning
VIDEO 1 VIDEO 2 VIDEO 3
SAT
TV
AUX
DMPORT
2CH
A.F.D.
DVD
SA-CD/CD TUNER
RECEIVER
MOVIE
MUSIC
SLEEP FM MODE D. TUNING AUTO CAL
FM MODE
1
2
3
4
5
6
7
8
9
CLEAR
0/10
– /– –
>10
GUIDE
ENTER
MEMORY
DISPLAY
1
If the FM stereo reception is poor and “ST”
flashes on the display, select monaural audio
so that the sound will be less distorted.
• To select monaural audio, you can
– press FM MODE repeatedly until the
“MONO” indicator lights up on the
display.
– set “FM MODE” in TUNER menu to “FM
MONO” (page 41).
• To return to stereo mode, you can
– press FM MODE repeatedly until the
“MONO” indicator on the display does not
light up.
– set “FM MODE” in TUNER menu to “FM
AUTO” (page 41).
V
B
B
v
2
RETURN/
EXIT
MENU
.
REPLAY ADVANCE
<
<
TUNING –
m
OPTIONS
TOOLS
>
TUNING +
H
M
X
x
DISC SKIP
55US
Tuner Operations
* The AM tuning scale can be changed (page 77).
Direct tuning
Presetting radio stations
You can enter the frequency of a station
directly by using the numeric buttons.
VIDEO 1 VIDEO 2 VIDEO 3
DVD
SA-CD/CD TUNER
SAT
TV
AUX
DMPORT
2CH
A.F.D.
3
2
5
6
7
8
9
CLEAR
0/10
– /– –
1
2
VIDEO 1 VIDEO 2 VIDEO 3
3
4
>10
Presetting radio stations
MUSIC
SLEEP FM MODE D. TUNING AUTO CAL
1
1
RECEIVER
MOVIE
You can preset up to 30 FM stations and 30
AM stations. Then you can easily tune in the
stations you often listen to.
ENTER
MEMORY
DMPORT
2CH
A.F.D.
SA-CD/CD TUNER
1
RECEIVER
MOVIE
MUSIC
1
2
3
4
5
6
7
8
9
CLEAR
0/10
4
Press TUNER repeatedly to
select the FM or AM band.
– /– –
ENTER
>10
GUIDE
MEMORY
DISPLAY
B
Press the numeric buttons to
enter the frequency.
B
v
RETURN/
EXIT
MENU
.
REPLAY ADVANCE
<
<
m
OPTIONS
TOOLS
>
TUNING +
TUNING –
H
M
DISC SKIP
X
Press ENTER.
TV VOL
MASTER VOL
If you cannot tune in a station
Make sure you have entered the right
frequency. If not, repeat steps 2 to 4. If you
still cannot tune in a station, the frequency is
not used in your area.
x
TV CH
PRESET
MUTING
Tip
If you have tuned in an AM station, adjust the
direction of the AM loop antenna for optimum
reception.
3,5
V
Press D.TUNING.
You can also use MEMORY/ENTER on
the receiver.
56US
AUX
4
Example 1: FM 102.50 MHz
Select 1 b 0 b 2 b 5 b 0
Example 2: AM 1,350 kHz
Select 1 b 3 b 5 b 0
4
TV
SLEEP FM MODE D. TUNING AUTO CAL
You can also use INPUT SELECTOR on
the receiver.
2
3
SAT
DVD
DVD
TOP MENU MENU
1
PRESET
+/–
F1
F2
TV INPUT
WIDE
Press TUNER repeatedly to
select the FM or AM band.
You can also use INPUT SELECTOR on
the receiver.
2
Tune in the station that you
want to preset using Automatic
Tuning (page 55) or Direct
Tuning (page 56).
Tuning to preset stations
VIDEO 1 VIDEO 2 VIDEO 3
Switch the FM reception mode, if
necessary (page 55).
3
Press MEMORY.
You can also use MEMORY/ENTER on
the receiver.
“MEMORY” lights up for a few seconds.
Perform steps 4 and 5 before
“MEMORY” goes out.
4
Press the numeric buttons to
select a preset number.
DMPORT
2CH
A.F.D.
DVD
SA-CD/CD TUNER
1
RECEIVER
MOVIE
MUSIC
1
2
3
4
5
6
7
8
9
CLEAR
0/10
– /– –
>10
GUIDE
ENTER
ENTER
MEMORY
DISPLAY
B
Tuner Operations
V
B
v
Press ENTER.
Repeat steps 1 to 5 to preset
another station.
AUX
Numeric
buttons
You can also use MEMORY/ENTER on
the receiver.
The station is stored as the selected preset
number.
If “MEMORY” goes out before you press
ENTER, start again from step 3.
6
TV
SLEEP FM MODE D. TUNING AUTO CAL
You can also press PRESET + or
PRESET – to select a preset number.
If “MEMORY” goes out before you
select the preset number, start again from
step 3.
5
SAT
OPTIONS
TOOLS
RETURN/
EXIT
MENU
.
REPLAY ADVANCE
<
<
>
TUNING +
TUNING –
H
m
M
DISC SKIP
X
TV VOL
MASTER VOL
x
TV CH
PRESET
MUTING
2
DVD
1
Press TUNER repeatedly to
select the FM or AM band.
2
Press PRESET + or PRESET –
repeatedly to select the preset
station you want.
Each time you press the button, you can
select a preset station as follows:
01
02
03
30
04
29
05
...
27
28
You can also press the numeric buttons to
select the preset station you want. Then,
press ENTER to enter the selection.
continued
57US
Using the controls on the
receiver
Naming preset stations
1 Turn INPUT SELECTOR to select the FM
or AM band.
2 Press TUNING MODE repeatedly to select
SAT
TV
SA-CD/CD TUNER
AUX
DMPORT
2CH
A.F.D.
RECEIVER
“PRESET T.”.
3 Press TUNING + or TUNING – repeatedly
to select the preset station you want.
MOVIE
MUSIC
1
3
SLEEP FM MODE D. TUNING AUTO CAL
1
2
3
4
5
6
7
8
9
CLEAR
0/10
– /– –
>10
GUIDE
ENTER
MEMORY
DISPLAY
V
5-8
B
B
v
1
RETURN/
EXIT
MENU
OPTIONS
TOOLS
.
REPLAY ADVANCE
<
<
>
4
Press TUNER repeatedly to
select the FM or AM band.
You can also use INPUT SELECTOR on
the receiver.
2
Tune in the preset station you
want to create an index name
for (page 57).
3
Press RECEIVER.
The RECEIVER indicator lights up and
receiver operation is activated.
4
Press MENU.
“1-LEVEL” appears on the display.
58US
5
Press V/v repeatedly to select
“4-TUNER”.
6
Press
menu.
7
Press V/v repeatedly to select
“NAME IN”.
or b to enter the
8
Press
or b to enter the
parameter.
The cursor flashes and you can select a
character. Follow the procedure given in
“To create an index name” below.
To create an index name
Other Operations
Switching between
digital and analog audio
(INPUT MODE)
1 Use V/v/B/b to create an index name.
Press V/v to select a character, then press
B/b to move the cursor to the next position.
If you made a mistake
Press B/b until the character you want to
change flashes, then press V/v to select the
correct character.
You can select the audio input mode setting
when you connect components to both digital
and analog audio input jacks on the receiver.
1
You can also use the input buttons on the
remote.
Tips
2 Press
to enter the name.
The entered name is registered.
2
Press INPUT MODE repeatedly
on the receiver to select the
audio input mode.
The selected audio input mode appears on
the display.
Audio input modes
x AUTO IN
Gives priority to digital audio signals when
there are both digital and analog connections.
If there are no digital audio signals, analog
audio signals are selected.
x COAX IN
Specifies the digital audio signals input to the
DIGITAL COAXIAL jack.
x OPT IN
Specifies the digital audio signals input to the
DIGITAL OPTICAL jack.
x ANALOG
Specifies the analog audio signals input to the
AUDIO IN (L/R) jacks.
Note
Some audio input modes may not be set up
depending on the input.
59US
Other Operations
• You can select the character type as follows by
pressing V/v.
Alphabet (upper case) t Numbers t
Symbols
• To enter a blank space, you can
– press V/v repeatedly until a blank space
appears in the display.
– press b without input a character.
Turn INPUT SELECTOR on the
receiver to select the input.
Enjoying the DIGITAL
MEDIA PORT
(DMPORT)
The DIGITAL MEDIA PORT (DMPORT)
allows you to enjoy sound from a network
system such as a portable audio source or
computer.
By connecting a DIGITAL MEDIA PORT
adapter (not supplied), you can enjoy sound
from the connected component on the
receiver.
For details, see the operating instructions
supplied with the DIGITAL MEDIA PORT
adapter.
Notes
• Do not connect an adapter other than the DIGITAL
MEDIA PORT adapter.
• Do not connect or disconnect the DIGITAL
MEDIA PORT adapter while the receiver is turned
on.
• Depending on the DIGITAL MEDIA PORT
adapter, video output may not be possible.
• The DIGITAL MEDIA PORT adapters are
available for purchase depending on the area.
60US
Connecting the DIGITAL MEDIA
PORT adapter
You can listen to the sound from the
component connected through the DIGITAL
MEDIA PORT adapter to the DMPORT jack
on the receiver.
You can also view the images on the TV
screen by connecting the video output of the
DIGITAL MEDIA PORT adapter to the
receiver.
To view the images, proceed to “Watching a
connected component through DMPORT
connection” on page 62.
TV
DIGITAL
OPTICAL
ANTENNA
DVD IN
SAT
IN
VIDEO 2/BD IN
OUT
HDMI
A
AM
VIDEO 2/
BD IN
COAXIAL
DVD
IN
VIDEO IN
VIDEO IN
VIDEO OUT VIDEO IN VIDEO OUT
MONITOR
DMPORT
DIGITAL MEDIA
PORT adapter
L
L
L
L
AUDIO OUT
R
R
OUT
IN
SA-CD/CD/CD-R
R
R
IN
AUDIO IN
AUDIO IN AUDIO OUT AUDIO IN
TV
SAT
DVD
VIDEO 1
SUB
WOOFE
Other Operations
A
To one of the
VIDEO IN jacks
VIDEO 3 IN/PORTABLE AV IN
VIDEO
L AUDIO R
Front panel
* The type of connector varies depending on the DIGITAL MEDIA PORT adapter.
For details, see the operating instructions supplied with the DIGITAL MEDIA PORT adapter.
A Video cord (not supplied)
To detach the DIGITAL MEDIA
PORT adapter from DMPORT
jack
DMPORT
2
1
Notes
• When connecting the DIGITAL MEDIA PORT
adapter, be sure the connector is inserted with the
arrow mark facing towards the arrow mark on the
DMPORT jack.
• Be sure to make DMPORT connections firmly,
insert the connector straight in.
• As the connector of the DIGITAL MEDIA PORT
adapter is fragile, be sure to handle with care when
placing or moving the receiver.
Press and hold both sides of the connector and
then pull out the connector.
61US
Listening to a connected
component through DMPORT
connection
1
7
Initial setting: –NONE
The assignable composite video input are
VIDEO 1, VIDEO 3, DVD and SAT
inputs.
Press DMPORT.
You can also use the INPUT SELECTOR
on the receiver to select “DMPORT”.
2
Start playback of the connected
component.
For example, select “–VIDEO 1”.
When you press DMPORT, the images
from the component connected to the
VIDEO 1 VIDEO IN jack through
DIGITAL MEDIA PORT adapter will
appear on the TV screen.
The sound is played back on the receiver.
For details, see the operating instructions
supplied with the DIGITAL MEDIA
PORT adapter.
Watching a connected
component through DMPORT
connection
You need to assign composite video input to
DMPORT input so that you can view the
images on the TV screen.
1
Press RECEIVER.
The RECEIVER indicator lights up and
receiver operation is activated.
2
Press MENU.
“1-LEVEL” appears on the display.
3
Press V/v repeatedly to select
“6-VIDEO”.
4
Press
menu.
5
Press V/v repeatedly to select
“DMPORT V.”.
6
Press
or b to enter the
parameter.
62US
or b to enter the
Press V/v repeatedly to select
the composite video input you
want to assign to DMPORT
input.
To return to the previous
display
Press B.
Notes
• Depending on the type of DIGITAL MEDIA
PORT adapter, you can operate the connected
component by using the remote. For details on
remote button operation, see page 10.
• Be sure you have made the video connection from
DIGITAL MEDIA PORT adapter to the receiver
(page 61).
• Be sure you have connected the MONITOR
VIDEO OUT jack of the receiver to the TV (page
61).
• Depending on the DIGITAL MEDIA PORT
adapter, video output may not be possible.
Tip
When listening to MP3 or other compressed music
using a portable audio source, you can enhance the
sound. Press MUSIC repeatedly to select
“PORTABLE” (page 51).
Naming inputs
Changing the display
You can enter a name of up to 8 characters for
inputs and display it on the receiver’s display.
This is convenient for labeling the jacks with
the names of the connected components.
You can check the sound field, etc., by
changing the information on the display.
Be sure to use the buttons on the receiver for
this operation.
1
Press DISPLAY repeatedly.
Press one of the input buttons
to select the input you want to
create an index name for.
You can also use INPUT SELECTOR on
the receiver.
2
Press RECEIVER.
The RECEIVER indicator lights up and
receiver operation is activated.
3
Press MENU.
“1-LEVEL” appears on the display.
Press V/v repeatedly to select
either “5-AUDIO” or “6-VIDEO”.
5
Press
menu.
6
7
Press V/v to select “NAME IN”.
or b to enter the
Press
or b to enter the
parameter.
All inputs except the FM and AM
band
Index name of the input* t Selected input t
Sound field currently applied
FM and AM band
Preset station name* t Frequency t
Sound field currently applied
* Index name appears only when you have assigned
one to the input or preset station (page 58, 63).
Index name does not appear when only blank
spaces have been entered, or it is the same as the
input name.
Note
Character or marks may not be displayed for some
languages.
The cursor flashes and you can select a
character. Follow the procedure given in
“To create an index name” (page 59).
63US
Other Operations
4
Each time you press the button, the display
changes cyclically as follows:
Using the Sleep Timer
You can set the receiver to turn off
automatically at a specified time.
Press SLEEP repeatedly while the
power is on.
Recording using the
receiver
Recording onto a CD-R
Each time you press the button, the display
changes cyclically as follows:
You can record onto a CD-R using the
receiver. See the operating instructions
supplied with your CD recorder.
2-00-00 t 1-30-00 t 1-00-00 t 0-30-00
1
t OFF
Press one of the input buttons
to select the playback
component.
When sleep timer is activated, the display
dims.
You can also use INPUT SELECTOR on
the receiver.
Note
If you press any buttons on the remote or receiver
after the display dims, the display brightens up.
After a while, the display dims again if no button is
pressed.
Tip
To check the remaining time before the receiver
turns off, press SLEEP. The remaining time appears
on the display. If you press SLEEP again, the sleep
timer will be canceled.
2
Prepare the playback
component for playing.
For example, tune to the radio station you
want to record (page 55).
3
Prepare the recording
component.
Insert a blank CD-R into the CD recorder
and adjust the recording level.
4
Start recording on the
recording component, then
start playback on the playback
component.
Note
Sound adjustments do not affect the signal output
from the SA-CD/CD/CD-R OUT jacks.
64US
Recording onto a recording
media
You can record from a video component using
the receiver. See the operating instructions
supplied with your recording component.
1
Press one of the input buttons
to select the playback
component.
You can also use INPUT SELECTOR on
the receiver.
2
Prepare the playback
component for playing.
For example, insert the video tape you
want to copy into the VCR.
3
Prepare the recording
component.
Using the Remote
Programming the remote
You can program the remote to control nonSony components by changing the code. Once
the control signals have been memorized, you
can use those components as part of your
system.
Furthermore, you can also program the remote
for Sony components that the remote is unable
to control. Note that the remote can only
control components that accept infrared
wireless control signals.
1
The RM SET UP indicator slowly flashes.
2
Insert a blank video tape, etc. into the
recording component (connected to
VIDEO 1 OUT jack) for recording.
Start recording on the
recording component, then
start playback on the playback
component.
Notes
• Some sources contain copy guards to prevent
recording. In this case, you may not be able to
record from the source.
• When DMPORT input is selected and you have
assigned VIDEO 1 input to DMPORT input, no
video signals are output from the VIDEO 1 VIDEO
OUT jack.
Press the input button for the
component you want to control.
For example, if you are going to control a
CD player, press SA-CD/CD.
The RM SET UP indicator lights up.
3
Press the numeric buttons to
enter the numeric code (or one
of the codes if more than one
code exists) corresponding to
the component and the maker
of the component you want to
control (except TV).
See the tables on page 67–70 for
information on the numeric code(s)
corresponding to the component and the
maker of the component (the first digit
and the last two digits of the numeric code
correspond to the category and the
maker’s code respectively).
continued
65US
Using the Remote
4
Press RM SET UP.
4
Press ENTER.
Once the numeric code has been verified,
the RM SET UP indicator slowly flashes
twice and the remote automatically exits
the programming mode.
5
Repeat steps 1 to 4 to control
other components.
Notes
• The indicator turns off while a valid button is
pressed.
• In step 2, if several input buttons are pressed, only
the last pressed button is valid.
• In step 2, if you press TUNER, you can only
program the button to control a tuner (page 70).
• In step 3, if an input button is pressed, the new
input is selected and the programming procedure
returns to the beginning of step 3.
• For the numeric codes, only the last three numbers
entered are valid.
To program the remote to
control a TV
1 Press RM SET UP.
The RM SET UP indicator slowly flashes.
2 Press TV.
3 Press the numeric buttons to enter the
numeric code (or one of the codes if more
than one code exists) for TV. For details, see
page 68.
4 Press ENTER.
Once the numeric code has been verified,
the RM SET UP indicator slowly flashes
twice and the remote automatically exits the
programming mode.
To cancel programming
Press RM SET UP during any step. The RM
SET UP indicator flashes 5 times in quick
succession. The remote automatically exits the
programming mode.
To activate the input after
programming
Press the programmed button to activate the
input you want.
66US
If programming is
unsuccessful, check the
following:
• If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
• If the indicator flashes 5 times in quick
succession while entering the numeric code,
an error has occurred. Start again from step
1.
To clear the memory of the
remote
To clear all programmes, do the following to
reset the remote to factory settings.
While holding down MASTER
VOL –, press and hold ?/1 and then
press AV ?/1.
The indicator flashes 3 times, then goes off.
The numeric codes
corresponding to the
component and the maker of
the component
Use the numeric codes in the tables below to
control non-Sony components and also Sony
components that the remote is normally unable
to control. Since the remote signal that a
component accepts differs depending on the
model and year of the component, more than
one numeric code may be assigned to a
component. If you fail to program your remote
using one of the codes, try using other codes.
Notes
• The numeric codes are based on the latest
information available for each brand. There is a
chance, however, that your component will not
respond to some or all of the codes.
• All of the input buttons on this remote may not be
available when used with your particular
component.
To control a CD player
To control an LD player
Maker
Code(s)
Maker
Code(s)
SONY
101, 102, 103
SONY
601, 602, 603
DENON
104, 123
PIONEER
606
JVC
105, 106, 107
KENWOOD
108, 109, 110
To control a video CD player
MAGNAVOX
111, 116
Maker
Code(s)
MARANTZ
116
SONY
605
ONKYO
112, 113, 114
PANASONIC
115
PHILIPS
116
PIONEER
117
TECHNICS
115, 118, 119
YAMAHA
120, 121, 122
To control a VCR
Maker
Code(s)
SONY
701, 702, 703, 704,
705, 706
AIWA*
710, 750, 757, 758
707, 708, 709, 759
To control a DAT deck
BLAUPUNKT
740
Maker
Code(s)
EMERSON
SONY
203
711, 712, 713, 714,
715, 716, 750
PIONEER
219
FISHER
717, 718, 719, 720
GENERAL ELECTRIC
(GE)
721, 722, 730
To control an MD deck
GOLDSTAR/LG
723, 753
Maker
Code(s)
GRUNDIG
724
SONY
301
HITACHI
722, 725, 729, 741
DENON
302
ITT/NOKIA
717
JVC
303
JVC
726, 727, 728, 736
KENWOOD
304
MAGNAVOX
730, 731, 738
MITSUBISHI/MGA
732, 733, 734, 735
Using the Remote
AKAI
To control a tape deck
NEC
736
Maker
Code(s)
PANASONIC
SONY
201, 202
729, 730, 737, 738,
739, 740
DENON
204, 205
PHILIPS
729, 730, 731
KENWOOD
206, 207, 208, 209
NAKAMICHI
210
PIONEER
729
RCA/PROSCAN
722, 729, 730, 731,
741, 747
PANASONIC
216
SAMSUNG
742, 743, 744, 745
PHILIPS
211, 212
SANYO
717, 720, 746
PIONEER
213, 214
SHARP
748, 749
TECHNICS
215, 216
TELEFUNKEN
751, 752
YAMAHA
217, 218
TOSHIBA
747, 756
ZENITH
754
* If an AIWA VCR does not work even though you
enter the code for AIWA, enter the code for Sony
instead.
continued
67US
To control a DVD player
To control a TV
Maker
Code(s)
Maker
Code(s)
SONY
401, 402, 403
SONY
501, 502
BROKSONIC
424
AIWA
536, 539, 501
DENON
405
AKAI
503
HITACHI
416
AOC
503
JVC
415, 423
CENTURION
566
MITSUBISHI
419
CORONADO
517
ORITRON
417
CURTIS-MATHES
503, 551, 566, 567
PANASONIC
406, 408, 425
DAYTRON
517, 566
PHILIPS
407
DAEWOO
PIONEER
409, 410
504, 505, 506, 507,
515, 544
RCA
414
FISHER
508, 545
416, 422
FUNAI
548
TOSHIBA
404, 421
FUJITSU
528
ZENITH
418, 420
GOLDSTAR/LG
503, 512, 515, 517,
534, 544, 556, 568
SAMSUNG
To control a DVD recorder
Maker
Code(s)
SONY
403
68US
GRUNDIG
511, 533, 534
HITACHI
513, 514, 515, 544,
557, 503, 519, 517,
571
ITT/NOKIA
521, 522
J.C.PENNY
503, 510, 566
JVC
516, 552
KMC
517
MAGNAVOX
503, 518, 544, 515,
517, 566
MARANTZ
527
MITSUBISHI/MGA
503, 519, 527, 544,
566, 568
NEC
503, 520, 544, 554,
517, 540, 566
NORDMENDE
530, 558
NOKIA
521, 522, 573, 575
PANASONIC
509, 524, 553, 559,
572
PHILIPS
515, 518, 557, 570,
571
PHILCO
503, 504, 514, 517,
518
PIONEER
509, 525, 526, 540,
551, 555
PORTLAND
503
QUASAR
509, 535
Maker
Code(s)
To control a satellite tuner
RADIO SHACK
503, 510, 527, 565,
567
Maker
Code(s)
SONY
801, 802, 803, 804,
824, 825, 865
AMSTRAD
845, 846
BskyB
862
GENERAL ELECTRIC
(GE)
866
RCA/PROSCAN
510, 523, 529, 544,
503
SAMSUNG
503, 515, 531, 532,
534, 544, 556, 557,
517, 562, 563, 566,
569
SAMPO
566
GRUNDIG
859, 860
SABA
547, 537, 549, 558,
530
HUMAX
846, 847
THOMSON
857, 861, 864
SANYO
508, 545, 546, 560,
567
PACE
848, 849, 850, 852,
862, 863, 864
SCOTT
503, 566
PANASONIC
818, 855
SEARS
517, 510, 508, 503,
518, 551
PHILIPS
856, 857, 858, 859,
860, 864, 874
SHARP
535, 550, 517, 561,
565
NOKIA
851, 853, 854, 864
RCA/PROSCAN
866, 871
SYLVANIA
503, 518, 566
THOMSON
530, 537, 547, 549
TOSHIBA
535, 539, 540, 541,
551
TELEFUNKEN
537, 538, 547, 549,
558, 530
BITA/HITACHI
868
HUGHES
867
JVC/Echostar/Dish
Network
873
872
875
869, 870
TEKNIKA
517, 518, 567
SAMSUNG
WARDS
503, 517, 566
TOSHIBA
YORK
566
ZENITH
542, 543, 567
To control a cable box
GE
509, 510, 503, 544
Maker
Code(s)
LOEWE
515, 534, 556
SONY
821, 822, 823
HAMLIN/REGAL
836, 837, 838, 839,
840
JERROLD/G.I./
MOTOROLA
806, 807, 808, 809,
810, 811, 812, 813,
814, 819
JERROLD
830, 831
OAK
841, 842, 843
PANASONIC
816, 826, 832, 833,
834, 835
PHILIPS
830, 831
PIONEER
828, 829
RCA
805
SCIENTIFIC ATLANTA 815, 816, 817
TOCOM/PHILIPS
830, 831
ZENITH
826, 827
continued
69US
Using the Remote
MITSUBISHI
To control a tuner
Maker
Code(s)
SONY
002, 005
To control a Blu-ray disc
recorder
Maker
Code(s)
SONY
310, 311, 312
To control a PSX
Maker
Code(s)
SONY
313, 314, 315
To control a DVD/VHS COMBO
Maker
Code(s)
SONY
411
To control a DVD/HDD COMBO
Maker
Code(s)
SONY
403
Additional Information
Glossary
x Component video
A format for transmitting video signal
information consisting of three separate
signals: luminance Y, chrominance Pb, and
chrominance Pr. High quality pictures, such as
DVD video or HDTV pictures, are transmitted
more faithfully. The three jacks are color coded green, blue and red.
x Composite video
A standard format for transmitting video
signal information. The luminance signal Y
and chrominance signal C are combined and
transmitted together.
x Dolby Digital
Digital audio encoding/decoding technology
developed by Dolby Laboratories, Inc. It
consists of front (left/right), center, surround
(left/right) and sub woofer channels. It is a
designated audio standard for DVD video and
also known as 5.1 channel surround. Since
surround information is recorded and
reproduced in stereo, more realistic sound with
fuller presence is delivered than with Dolby
surround.
x Dolby Pro Logic II
This technology converts 2 channel stereo
recorded audio into 5.1 channel for playback.
There is a MOVIE mode for movies and
MUSIC mode for stereo sources such as
music. Old movies encoded in the traditional
stereo format can be enhanced with 5.1
channel surround sound.
70US
x Dolby Surround (Dolby Pro
Logic)
Audio processing technology developed by
Dolby Laboratories, Inc. Center and mono
surround information is matrixed into two
stereo channels. When reproduced, audio is
decoded and output in 4 channel surround
sound. This is the most common audio
processing method for DVD video.
x DTS Digital Surround
Digital audio encoding/decoding technology
for theaters developed by DTS, Inc. It
compresses audio less than Dolby Digital,
delivering a higher quality sound
reproduction.
x HDMI (High-Definition
Multimedia Interface)
HDMI is an interface that supports both video
and audio on a single digital connection. The
HDMI connection carries standard to high
definition video signals and multi channel
audio signals to audio/video components, such
as HDMI equipped TVs, in digital form
without degradation. The HDMI specification
supports HDCP (High-bandwidth Digital
Contents Protection), a copy protection
technology that incorporates coding
technology for digital video signals.
To convert analog audio to digital, analog data
should be quantified. This process is called
sampling, and the number of times per second
the analog data is quantified is called the
sampling frequency. A standard music CD
stores data quantified at 44,100 times per
second, which is expressed as a sampling
frequency of 44.1 kHz. Generally speaking, a
higher sampling frequency means better sound
quality.
On safety
Should any solid object or liquid fall into the
cabinet, unplug the receiver and have it
checked by qualified personnel before
operating it any further.
On power sources
• Before operating the receiver, check that the
operating voltage is identical with your local
power supply.
The operating voltage is indicated on the
nameplate on the back of the receiver.
• The unit is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the unit
itself has been turned off.
• If you are not going to use the receiver for a
long time, be sure to disconnect the receiver
from the wall outlet. To disconnect the AC
power cord, grasp the plug itself; never pull
the cord.
• One blade of the plug is wider than the other
for the purpose of safety and will fit into the
wall outlet only one way. If you are unable to
insert the plug fully into the outlet, contact
your dealer.
• The AC power cord must be changed only at
a qualified service shop.
On heat buildup
Although the receiver heats up during
operation, this is not a malfunction. If you
continuously use this receiver at a large
volume, the cabinet temperature of the top,
side and bottom rises considerably. To avoid
burning yourself, do not touch the cabinet.
continued
71US
Additional Information
x Sampling frequency
Precautions
On placement
• Place the receiver in a location with adequate
ventilation to prevent heat buildup and
prolong the life of the receiver.
• Do not place the receiver near heat sources,
or in a place subject to direct sunlight,
excessive dust, or mechanical shock.
• Do not place anything on top of the cabinet
that might block the ventilation holes and
cause malfunctions.
• Do not place the receiver near equipment
such as a TV, VCR, or tape deck. (If the
receiver is being used in combination with a
TV, VCR, or tape deck, and is placed too
close to that equipment, noise may result,
and picture quality may suffer. This is
especially likely when using an indoor
antenna. Therefore, we recommend using an
outdoor antenna.)
• Use caution when placing the receiver or
speakers on surfaces that have been specially
treated (with wax, oil, polish, etc.) as
staining or discoloration of the surface may
result.
On operation
Before connecting other components, be sure
to turn off and unplug the receiver.
If you encounter color
irregularity on a nearby TV
screen
The front speakers, center speaker and the sub
woofer are magnetically shielded to allow
them to be installed near a TV set. However,
color irregularities may still be observed on
certain types of TV sets.
As the surround speakers are not magnetically
shielded, we recommend that you place the
surround speakers slightly further away from
the TV set (page 15).
If color irregularity is
observed...
Turn off the TV set, then turn it on again after
15 to 30 minutes.
72US
If color irregularity is observed
again...
Place the speaker further away from the TV
set.
If howling occurs
Reposition the speakers or turn down the
volume on the receiver.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzine.
If you have any questions or problems
concerning your receiver, please consult your
nearest Sony dealer.
Troubleshooting
If you experience any of the following
difficulties while using the receiver, use this
troubleshooting guide to help you remedy the
problem.
Audio
There is no sound from a specific
component.
• Check that the component is connected
correctly to the audio input jacks for that
component.
• Check that the cord(s) used for the
connection is (are) fully inserted into the
jacks on both the receiver and the
component.
There is no sound from analog 2
channel sources.
• Check that the INPUT MODE is not set to
“COAX IN” or “OPT IN” for the selected
input (page 59).
There is no sound from digital sources
(from COAXIAL or OPTICAL input jack).
• Check that the INPUT MODE is not set to
“ANALOG” (page 59).
There is no sound from the speakers of
the receiver when you connect the
receiver and the playback component
via a HDMI connection.
• Make sure that you have connected the
digital audio jacks on the playback
component to the receiver (page 21). Then,
turn off or mute the TV’s volume.
The left and right sounds are
unbalanced or reversed.
• Check that the speakers and components
are connected correctly and securely.
• Adjust the balance parameters using the
LEVEL menu.
continued
73US
Additional Information
There is no sound, no matter which
component is selected, or only a very
low-level sound is heard.
• Check that the speakers and components
are connected securely.
• Check that both the receiver and all
components are turned on.
• Check that MASTER VOLUME is not set
to “VOL MIN”.
• Check that the SPEAKERS (OFF/A/B/
A+B) is not set to off (page 30).
• Check that headphones are not connected.
• Press MUTING to cancel the muting
function.
• Check that you have selected the correct
component with the input buttons (page
36).
• The protective device on the receiver has
been activated. Turn off the receiver,
eliminate the short-circuit problem, and
turn on the power again.
There is no sound from one of the front
speakers.
• Connect a pair of headphones to the
PHONES jack to verify that sound is
output from the headphones. If only one
channel is output from the headphones, the
component may not be connected to the
receiver correctly. Check that all the cords
are fully inserted into the jacks on both the
receiver and the component. If both
channels are output from the headphones,
the front speaker may not be connected to
the receiver correctly. Check the
connection of the front speaker which is
not outputting any sound.
• Make sure you have connected to both the
L and R jacks of an analog component, and
not only to either the L or R jack. Use an
audio cord (not supplied).
There is severe hum or noise.
• Check that the speakers and components
are connected securely.
• Check that the connecting cords are away
from a transformer or motor, and at least
10 feet away from a TV set or fluorescent
light.
• Move your audio components away from
the TV.
• The plugs and jacks are dirty. Wipe them
with a cloth slightly moistened with
alcohol.
There is no sound, or only a very lowlevel sound is heard from the center/
surround speakers.
• Select a CINEMA STUDIO EX mode
(page 52).
• Adjust the speaker level (page 34).
There is no sound from the sub woofer.
• Check that the sub woofer is connected
correctly and securely.
• Make sure you have turned on your sub
woofer.
The surround effect cannot be
obtained.
• Make sure the sound field function is on
(press MOVIE or MUSIC).
• Sound fields do not function for signals
with a sampling frequency of more than
48 kHz.
Dolby Digital or DTS multi channel
sound is not reproduced.
• Check that the DVD, etc. you are playing
is recorded in Dolby Digital or DTS
format.
• When connecting the DVD player, etc., to
the digital input jacks of this receiver,
check the audio setting (the settings for the
audio output) of the connected component.
74US
Recording cannot be carried out.
• Check that the components are connected
correctly.
• Select the source component using the
input buttons (page 36).
Video
There is no picture or an unclear
picture appears on the TV screen.
• Select the appropriate input using the input
buttons.
• Set your TV to the appropriate input mode.
• Move your audio components away from
the TV.
• Assign the composite video input to
DMPORT input correctly.
• Depending on the DIGITAL MEDIA
PORT adapter, video output may not be
possible.
The source image input to the HDMI
jack on the receiver is not output from
the TV.
• Check the HDMI connection.
• Depending on the playback component,
you may need to set up the component.
Refer to the operating instructions
supplied with each component.
Recording cannot be carried out.
• Check that the components are connected
correctly.
• Select the source component using the
input buttons (page 36).
Tuner
Remote commander
The FM reception is poor.
• Use a 75-ohm coaxial cable (not supplied)
to connect the receiver to an outdoor FM
antenna as shown below. If you connect
the receiver to an outdoor antenna, ground
it against lightning. To prevent a gas
explosion, do not connect the ground wire
to a gas pipe.
The remote does not function.
• Point the remote at the remote sensor on
the receiver.
• Remove any obstacles in the path between
the remote and the receiver.
• Replace all the batteries in the remote with
new ones, if they are weak.
• Make sure you select the correct input on
the remote.
• The AUX button on the remote are not
available for receiver operation.
• When you operate a programmed nonSony component, the remote may not
function properly depending on the model
and the maker of the component.
Outdoor FM antenna
Receiver
ANTENNA
AM
Ground wire
(not supplied)
To ground
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. Refer to the following
table to solve the problem. If any problem
persists, consult your nearest Sony dealer.
If an error message appears while you perform
Auto Calibration, see “Error and warning
codes” (page 33) to solve the problem.
DEC. EROR
Appears when a signal the receiver cannot
decode (ex. DTS-CD) is input and “DEC.
PRI.” in the AUDIO menu is set to “DEC.
PCM”. Set it to “DEC. AUTO” (page 42).
PROTECT
Irregular current is output from the
speakers. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
continued
75US
Additional Information
Radio stations cannot be tuned in.
• Check that the antennas are connected
securely. Adjust the antennas and connect
an external antenna, if necessary.
• The signal strength of the stations is too
weak (when tuning in with automatic
tuning). Use direct tuning.
• Make sure you set the tuning interval
correctly (when tuning in AM stations
with direct tuning).
• No stations have been preset or the preset
stations have been cleared (when tuning by
scanning preset stations). Preset the
stations (page 56).
• Press DISPLAY repeatedly on the receiver
so that the frequency appears on the
display.
Error messages
If you are unable to remedy the
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy
the problem (page 29). However, note that all
memorized settings will be reset to their
factory settings and you will have to readjust
all settings on the receiver.
If the problem persist
Consult your nearest Sony dealer. Note that if
service personnel changes some parts during
repair, these parts may be retained.
Reference sections for clearing
the receiver’s memory
To clear
See
All memorized settings
page 29
Customized sound fields
page 54
Specifications
AUDIO POWER
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(Models of area code U only)
With 6 ohm loads, both channels driven, from
120 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than 1%
total harmonic distortion from 250 milliwatts
to rated output.
Amplifier section
Power Output1)
Models of area code U, CA
Stereo mode (6 ohms, 1 kHz, THD 1%)
90 W + 90 W
Surround mode2) (reference) (6 ohms, 1 kHz,
THD 10%)
RMS output
FRONT:140 W
per channel
CENTER:140 W
SURROUND:140 W
per channel
1)
Measured under the following conditions:
Area code
Power requirements
U, CA
120 V AC, 60 Hz
2) Reference
power output for front, center and
surround speakers. Depending on the sound field
settings and the source, there may be no sound
output.
Inputs
Analog
Sensitivity: 800 mV/
50 kohms
Digital (Coaxial) Impedance: 75 ohms
Outputs (Analog)
AUDIO OUT
Voltage: 800 mV/
10 kohms
SUB WOOFER Voltage: 2 V/1 kohm
Tone
Gain levels
±6 dB, 1 dB step
76US
Reproduction frequency range:
28 – 20,000 Hz
FM tuner section
Tuning range
87.5 - 108.0 MHz
Antenna
FM wire antenna
Antenna terminals 75 ohms, unbalanced
Intermediate frequency
10.7 MHz
AM tuner section
Tuning range
Models of area code U, CA
With 10-kHz tuning scale:
530 – 1,710 kHz3)
With 9-kHz tuning scale:
531 – 1,710 kHz3)
Antenna
Loop antenna
Intermediate frequency
450 kHz
3)
You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. While holding down TUNING
MODE, press ?/1. All preset stations will be
erased when you change the tuning scale. To reset
the scale to 10 kHz (or 9 kHz), repeat the
procedure.
Video section
Area code
Power consumption
U
200 W
CA
270 VA
Power consumption (during standby mode)
0.3 W
Dimensions (width/height/depth) (Approx.)
17 × 6 1/4 × 12 1/4 inches
(430 × 157.5 × 310 mm)
including projecting parts
and controls
Mass (Approx.)
17 lb 4 oz (7.8 kg)
Speaker section
• Front speakers (SS-MSP900)
• Center speaker (SS-CNP680)
• Surround speakers (SS-SRP900)
Front/center speakers
Full range, magnetically
shielded
Surround speakers Full range
Speaker units
2 7/8 inches (70 mm)
cone type
Enclosure type
Close type
Rated Impedance
6 ohms
Dimension (width/height/depth) (Approx.)
6 1/8 × 3 7/8 × 4 inches
(155 × 96 × 101 mm)
Mass (Approx.)
Front/center speaker
1 lb 9 oz (0.7 kg)
Surround speaker
1 lb 2 oz (0.5 kg)
General
Power requirements
Area code
Power requirements
U, CA
120 V AC, 60 Hz
Power output (DIGITAL MEDIA PORT)
DC OUT:
5V, 700 mA
continued
77US
Additional Information
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
PB/CB: 0.7 Vp-p, 75 ohms
PR/CR: 0.7 Vp-p, 75 ohms
80 MHz HD Pass Through
Power consumption
• Sub woofer (SA-WP780)
Supplied speakers
AUDIO POWER
SPECIFICATIONS
Front speakers (2)
Center speaker (1)
Surround speakers (2)
Sub woofer (1)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(Models of area code U only)
With 6 ohm loads, from 28 – 200 Hz; rated 120
watts, minimum RMS power, with no more
than 1% total harmonic distortion from 250
milliwatts to rated output.
Speaker system
Speaker unit
Enclosure type
RMS output
Input
Active subwoofer,
magnetically shielded
7 7/8 inches (200 mm)
cone type
Acoustically loaded bass
reflex
200 W
LINE IN (input pin jacks)
Power requirements
Area code
Power requirements
U, CA
120 V AC, 60 Hz
FM wire antenna (1)
AM loop antenna (1)
Monaural audio cord (1)
Speaker cords
• Long (2)
• Short (3)
Coaxial digital cord (1)
Foot pads
• Speakers (20)
• Sub woofer (4)
Remote commander RM-AAP017 (1)
R6 (size-AA) batteries (2)
Optimizer microphone (ECM-AC2 or
ECM-AC2a) (1)
For details on the area code of the
component you are using, see page 3.
Design and specifications are subject to
change without notice.
Power consumption
Area code
Power consumption
U, CA
80 W
Dimensions (width/height/depth) (Approx.)
10 3/4 × 13 1/8 × 15 inches
(270 × 331 × 380 mm)
Mass (Approx.)
18 lb 5 oz (8.3 kg)
78US
Supplied accessories
Index
Numerics
I
T
2CH STEREO 54
5.1 channel 15
Initial setup 29
INPUT MODE 59
A
M
AUTO CALIBRATION 31
AUTO FORMAT DIRECT
(A.F.D.) 49
Menu
A. CAL 49
AUDIO 45
LEVEL 43
SUR 44
SYSTEM 47
TONE 44
TUNER 45
VIDEO 46
Muting 36
TEST TONE 34
Tuner
connecting 28
Tuning
automatically 55
directly 56
to preset stations 57
TV
connecting 23
B
Blu-ray disc player
connecting 21
C
CD player
connecting 19
playback 38
CD recorder
connecting 19
D
E
Error messages 75
H
HDMI
connecting 21
VCR
connecting 27
Video game
connecting 27
N
Naming 58, 63
R
Recording
onto a CD-R 64
onto a recording media
65
Remote commander 10
Additional Information
Digital Cinema Sound
(DCS) 53
DIGITAL MEDIA PORT
connecting 61
input 36
video assign 62
Dolby Digital 70
DTS 71
DVD player
connecting 24
playback 39
DVD recorder
connecting 25
V
S
Satellite tuner/Set-top box
connecting 26
Selecting
component 36
sound field 51
speaker system 30
Sleep Timer 64
Sound fields
resetting 54
selecting 51
Speakers
connecting 17
installing 15
Super Audio CD player
connecting 19
playback 38
79US
Sony Corporation Printed in Malaysia