iCool Lite - iCoolsport
iCool Lite
New Features for 2013:
Lighter weight: 5Kg (10 lbs) lighter than the previous model
Smaller Size: Height reduced by 52mm (2 inches)
All New Water
Circulation System: A New light weight linear water pump system is now integrated directly
into a special water hose line. This adds both safety and convenience.
The new technology in line linear pump system allows you to use your iCool Lite not just with any iCool pool, but with optional low cost attachments, it allows you to use your Lite with virtually any small pool, spa or bath tub.
The new pump is completely waterproof and can even be fully submerged in water if you need to pump up and over the side of a bathtub.
The new pump operates from very safe low voltage for total safety.
WARNING: Do not use with Chlorine, Bromide or Salt!
OWNER’S MANUAL FOR iCOOL RECOVERY SYSTEMS
INTRODUCTION
Your iCool Lite is smallest system available that can provide the full range of ice bath therapy temperatures in any single
person iCool pool or any normal sized bathtub. It’s breakthrough technology packs the most cooling power possible in
such a small space. The Lite is designed for either fixed position operation or for easy transportation to almost anywhere
you need to provide ice bath recovery.
To avoid damage it should always be transported in the purpose designed iCool military grade protective travel case,
available as an option.
PERFORMANCE
Your iCool Lite has impressive performance for such a small system, but naturally it can not cool a pool as fast as our
much larger iCools. You can expect cooling of at least 3 to 5 degrees C per hour and it may cool even faster depending
your basic setup and local conditions. The temperature in the operating area, the amount of water being cooled and the
starting temperature of the water will all have some effect.
FOR BEST PERFORMANCE
Operate in a well ventilated shaded area. Definitely not in direct sunlight.
Use an insulated pool (all iCool pools are properly insulated).
Use an insulating matt under the pool to prevent loss of cold into the ground. (All iCool pools have built in insulated mats
but adding an extra mat can really help performance).
Use a pool cover. (All iCool pools come with a standard cover).
When water is very cold the difference between the pool water and the room temperature is very large, so the cold can
be quickly lost. Good insulation reduces these losses. Good insulation will result in much faster cooling and save a lot
of electricity.
HOLDING THE SET TEMPERATURE
In normal conditions, once your pool reaches your set temperature your iCool Lite has been designed to have enough
cooling power to continue to hold that temperature even if several athletes are using the pool.
NEVER USE CORROSIVE CHEMICALS
Bromide and Chlorine can cause major long term damage even to the high grade stainless steel heat exchanger in your
iCool and could eventually cause a total system failure that is not covered by your warranty. These chemicals eat away
most metals and can also be harmful to athletes. This model iCool has a stainless steel heat exchanger tank that must
only be used with fresh clean water. To control bacteria, a small amount of mild bathroom type disinfect is effective. Also
avoid the use of salt water to ensure long life of your system.
For extended use of the same pool water, iCool offers an optional small light weight filtration system that allows
extended multi athlete use. It is fully compatible with your Lite. Please see our website for advice.
POOL SETUP ADVICE
Before you turn on your iCool system you must set up and fill the pool. iCool portable inflatable pools come with their
own instructions and are easy to set up. Please be sure that they are in the position you require before you fill them
with water as the weight of the water will make it impossible to move them once they are filled.
IMPORTANT SAFETY ADVICE
Power supply voltage must be observed. Your iCool Lite can only be used with the voltage marked on the machine, it
is not multi voltage. The voltage is marked under to the main power socket. It will be either 110volts (USA) or 220volts
(Europe etc). To ensure safe operation the power outlet you use must have a proper earth connection.
BUILT IN SAFETY SYSTEMS
Your iCool system has many safety features to protect against such things as a loss of water flow, overheating of the
system, or any chance of the user receiving an electrical shock. If any such potentially dangerous things should occur,
in most cases your iCool will shut itself down and a red warning screen will appear to assist you to identify and correct
the problem. In the case of overheating, the main fan will continue to run for some time until the temperature is safely
back to normal. For the safety of users, any leakage of even a small amount of electrical current will cause the system
to instantly remove all electrical power.
In the unlikely event that your system shuts itself down for any of these reasons, you must identify and correct the
problem that has caused the safety systems to operate before allowing anyone to use the system.
TEST THE EARTH LEAKAGE SAFETY DEVICE REGULARLY
The main power switch is also part of the electrical safety circuit that can prevents the possibility of electric shock. It is
essential to test this safety system each time you use the iCool to make certain it is operating correctly. This is very easy
to do and takes only a few seconds.
Turn on the main switch (blue colour) and then press the orange test button marked T just above the switch. If the
safety system is working normally, pressing the test button will cause the main power switch to shut off instantly. After a
successful test, reset the main switch to ON to begin normal operation. If pressing the test button fails to instantly shut
off the power switch do not use the system until you contact iCool for advice. Failures of this system are very rare.
ADVICE ABOUT OBTAINING THE CORRECT FLOW OF WATER
occasionally you may experience some difficulty getting the water to flow correctly through your iCool due to trapped
air in the system or the hoses. Read these simple instructions to learn how to correct this.
THE PUMP: Water flow through your iCool is produced by a high quality long life circulating pump that, for the complete
safety of the user, operates on a very safe low voltage and outside of the iCool’s cooling machinery.
Circulating type pumps can lift and move water reliably for many thousands of hours, however they do not provide
suction and are therefore not self priming. Self priming type pumps are not as reliable over long periods and so are not
suitable for this type of operation.
The pump with your iCool cannot begin to operate correctly unless it is fed with a head of water from a pool where the
level is above the pump and any air tapped in the feeding hoses is removed. The water in the pool must be above the
pump before you start it. There must be no air trapped in the supply hose from the pool to the pump and no part of the
hose from the pool to the pump can be above the level of the water because this will trap air that can prevent water from
flowing to the pump.
There are several easy ways to clear trapped air. For example, before you connect the outlet hose from the pump to the
iCool, fill the pump with water and then connect it, that will remove all of the trapped air.inside the pump. If this does not
work immediately then you can touch the pump on off button 3 or 4 times so the pump is off for about 5 to 10 seconds
each time. The surge when the pump starts can often clear the trapped air but it may take a few times if there is a lot of
trapped air.
If you still do not have a good flow of water, with the pump running, undo the levers on the snap hose fitting that connects
the hose from the pump to the bottom inlet on the iCool. There is no need to remove the fitting, just open the levers and
this will allow any trapped air to escape. As soon as you see water coming out of fitting, quickly snap it back into position
and lock it again.
You only need to bleed the system once for each set up. Once primed of air, the system will remain primed and water
will normally flow instantly each time you start the pump until the pool is emptied or the iCool is moved.
Never operate the pump without water. Water pumps can not operate for long periods without water because the water
provides the lubrication to the bearings. To prevent damage, your iCool system will shut down the pump automatically if
water is not flowing properly for more than 2 minutes. If this happens a warning screen will normally appear to explain
to you how to correct the problem.
OWNER’S MANUAL FOR iCOOL RECOVERY SYSTEMS
All iCool Lite Models from January 2013
iCoolsport.com
Page 3
Quick
start guide
The following is a quick start guide to get your iCool up and running quickly, however you should read the
entire manual to get the most out of your iCool.
STEP 1
Before you fill the pool you must connect the PUMP MODULE and the 2 hoses provided to the inlet and outlet fittings
on the Lite unit. ICool hoses have convenient snap fittings that are very quick and easy to use.
The large hose with the circulating pump in line connects from the bottom of the pool to the bottom inlet fitting on the Lite
To top
of pool
PUMP MODULE
o
To t
tion
nnec
co
ottom
To b
on
ecti
nn
p co
Screw the other connection hose provided to the pump,
then connect the snap connector on the other end to the
bottom of the pool
Plug in pump as shown.
Please be sure that the pins are
aligned correctly to avoid damage.
Turn outer ring half a turn to lock in place.
The iCool must be on the same level surface as the pool. It must not be above the pool. The pump must be on the
floor and lower than the water in the pool. The water level in the pool must be well above the pump and the hose pipe
with the pump must be flat on the floor to prevent air being trapped.
WATER FLOW WARNING
If water does not flow correctly after 2
minutes either during the initial set up or at
any time during normal operation an alarm
will sound.
The system will stop to protect the pump
and a red warning screen will appear with
instructions.
You must find the reason for the lack of
water flow or the system will stop every
2 minutes for safety until the water flow is
correct. The Water Flow Warning Screen
also provides an option to over ride the
flow protection system in the rare situation
of a false alarm.
Never use this option unless you are
absolutely certain that the system is stopping because of a false water flow alarm!
Once you use this function to disarm the flow safety monitor nothing will stop the system even if water is not flowing and
this can seriously damage the pump as it will have no lubrication or cooling from the water.
This over ride function is only to be used for short periods where it is essential to keep your system operating until the
reason for the false alarm can be determined and corrected. Water flow can also stop if the heat exchanger tank is
frozen solid!
If you set the temperature below about 7ºC or 45ºF it is occasionally possible in certain climatic conditions for the heat
exchange tank to freeze solid which will block most , but not all, of the flow of water.
A small amount of water may still be flowing through the automatic air bleed system which bypasses the heat exchanger,
but the safety system monitors the heat exchanger tank flow only and if no water is flowing through the tank the system
will stop.
In order to cool the pool water to these extremely low temperatures the system must cool to at least 5 to 7ºC below the
set temperature and this takes it very close to the temperature that water freezes solid.
Following international safety standards your iCool will not accept water temperature settings below 6ºC or 42ºF as this
would put athletes using the system unattended at risk of hypothermia. However, the iCool is easily powerful enough to
freeze the water inside the system itself and if this happens the safety screen above will appear and the system will stop.
Please be aware that the tank can only freeze if your setting is below 7 to 8ºC and this can only happen in certain
conditions. If your set temperature is above this then it is much more likely that the system has stopped because of a
lack of water flow caused by either a hose or filter obstruction, or an air leak in the hoses, or trapped air in the system.
If there is a possibility that the heat exchanger tank is frozen, then you must allow the system to warm up for about 15
minutes to thaw the ice. Leave the power switched on so that the fan can operate if necessary to thaw out the tank. Set
a new temperature no lower than 8 or 9ºC before restarting so that the tank does not freeze again.
STEP 3
Connect the power cable provided with your iCool to a standard power outlet capable
of providing at least 10 amps in countries with a 220 V supply and 20 amps in countries
with a 110 V supply. Although the system requires much less power than this in normal
operation, all heat pump compressor motors need considerably more power for a minute
or so each time they starts up. For safety, the power outlet you use must be earthed
correctly. The main power switch is also part of the electrical safety circuit that prevents
the possibility of electric shock. It is a good idea to test this system each time you use the
iCool by turning on the main switch and then pressing the test button above the switch. If
the safety system is working normally, pressing the test button will cause the main power
switch to shut down instantly. After this test, reset the main switch to ON to begin normal
operation.
OWNER’S MANUAL FOR iCOOL RECOVERY SYSTEMS
All iCool Lite Models from January 2013
iCoolsport.com
Page 5
STEP 4
TURN ON THE MAIN POWER SWITCH
Your system software will begin loading.
Your iCool has a full colour high-resolution touchscreen that
eliminates all switches and provides complete control over your
iCool system in a user-friendly and intuitive manner. It also provides
a substantial amount of additional information to assist you. When
you turn on the power for the first time the system will load the
latest software from its memory card and run a diagnostic self test
routine. This will take about 20 seconds. During this time you will
see this screen
(shown at right) and then a BLACK screen.
the software loading screen
The icool logo will flash white.
The iCool logo is the system status bar, it changes colour or flashes to give a clear
indication of each function.
While the software is loading it will flash white, the welcome screen shown above will
appear and then a black screen appears for about 15 seconds while the computers test
the safety systems.
When your personal logo screen (see examples below) appears it will stop flashing and
show a steady white light to indicate that the systems check was successful and that your
iCool is ready to use.
THE iCOOL STATUS LIGHT
If you did not request a personal logo screen then the standard iCool start
screen will appear. A personal logo welcome screen similar to these samples will appear at this time.
Touch the logo screen anywhere to continue.
The main operating screen provides many options which are covered
elsewhere in this manual, however to quickly start the system you
can simply accept the default water temperature setting of 15ºC or
touch the change settings button to select a different temperature.
10ºC will be inserted automatically but you can change to any
temperature you require. The temperatures can also be displayed
in Fahrenheit. This is explained later in this Manual.
Simply touch the up and down arrow buttons and the desired pool
water temperature will appear on the bottom left-hand of the screen
in the blue window marked “selected temperature”. The right-hand
side of the screen shows the outside air temperature.
START
START
24
15
30 22
MAIN OPERATING SCREEN
Once the pool water temperature you want your iCool to cool to is
showing, touch the start button. This takes you back to the main run
screen which is the screen that you will use most of the time during
normal operation.
STEP 5
Touch the start pump button. This will start the pump operating and
water should begin circulating. The iCool Status Logo will turn blue
to indicate that the water pump is on. Note: When you touch start
buttons they change to stop buttons and can then be used to stop
that function if required.
it is essential that the water is flowing correctly before you touch the
start system button.
The water flow is pre set to an optimum flow of about 10-15 litres
or around 2-4 gallons per minute. This allows time for the heat
exchanger to operate at maximum cooling efficiency.
Pool water is completely changed approximately every 15 to
20 minutes.
START
START
START
10
START
22
water temperature setting screen
Do not touch the start system button until you are sure that water is flowing smoothly. If water does not flow smoothly
within a minute, please check that the hose from the bottom of the pool is flat on the floor and no part of it is higher
than the top of the water. Check that the water in the pool is higher than the pump. If this does not correct the problem
the system will sound an alarm and a red warning screen will appear with information about how to correct the water
flow problem.
STEP 6
Now that you have pre set your desired temperature and started the circulating pump, the touch screen should look like
the picture at the top of this page. (of course the temperatures may be different). Notice that the pump button will have
changed from start to stop. You can use this same button to start and stop the pump at any time.
Now, touch the start system button and the cooling cycle will begin. The iCool Status Logo will turn green to indicate that
the water is being cooled to your preset temperature. When that temperature is reached the system will then cycle to
maintain it at that temperature automatically.
The SYSTEM can only be started once within any 3 minute period to avoid overloading the compressor. If you don’t
hear it start do not touch the START SYSTEM again, it will start automatically after the 3 minutes safety period elapses.
If your iCool is the contrast model (cold and Hot) then, depending on the temperature you set, it will either heat or
cool the water automatically to reach your preset temperature and then maintain it at that temperature. More detailed
information about the operation of the contrast version can be found later in this manual.
for the safety of users, you can not set temperatures below 5°c or above 45°c. (40°f-112°f) in an emergency you can
stop all functions immediately by touching the “all stop” button however, if the cabinet is hot, the fan may continue to
run until the cabinet has cooled.
OWNER’S MANUAL FOR iCOOL RECOVERY SYSTEMS
All iCool Lite Models from January 2013
iCoolsport.com
Page 7
IF THE iCOOL STATUS light TURNS RED WHEN YOU START THE COOLING CYCle:
The can only occur if the water temperature in the pool is already be lower than the cooling temperature you set. In this
case the iCool will automatically attempt to heat the water to match the temperature you have set. The red iCOOL lights
to indicate activation of the heating mode. You can not set the Lite to cool water that is already colder than your setting.
No heating can occur if your model does not have the heating option.
START
START
STOP
START
24
10
30
22
MAIN OPERATION screen
details of the main operating screen
The pool temperature window shows the actual water temperature returning from the pool. This will vary slightly to the
actual temperature in the pool because for safety reasons the electronic sensor is in the cooling unit not in the pool.
It accurately reads the actual temperature of the water that is returning to the pool. The actual pool temperature will
be slightly different depending on your particular setup. The temperature is always accurately maintained but if you
want to display the actual pool temperature within 1 degree you can simply set an offset amount to compensate for the
difference when selecting your required temperature.
The heat pump temperature window shows the temperature inside the cabinet. If this exceeds 70°C or 158°F the system
will shut down, an alarm will sound and a warning screen will appear. This could happen in extremely hot conditions or
if the unit is covered by an object such as a towel or anything that prevents proper airflow.
The outside temperature window shows the current room or outside temperature. It is not desirable to operate this
system in temperatures above 42°C or 108° F. If the reading exceeds this you need to move the system to a cooler
area or improve the air flow. The preset temperature window always shows your selected temperature. This is the
temperature the water will be automatically cooled (or heated) to and maintained at.
Changing the temperature setting
You can change your preset temperature at any time by touching the change setting button, this will take you to the
change settings screen. From here you proceed as described previously. If you have the contrast model, for safety
reasons you cannot change directly from heating to cooling or cooling to heating. To do this you must switch off the entire
system at the main switch and start again. This is required to reset the computer.
FAN SPEEDS
During normal operation the main fan will automatically change speeds as required to maintain the highest efficiency.
The fan will be at full speed when temperatures are high or the water is warm.
You can display the pool temperature at full-screen size.
If you touch the number in the pool temperature window on the Main Operation Screen for a few seconds the screen will
change to a full-screen display of that temperature.
This is useful if you wish to monitor the system from a distance. The pre-set temperature and the outside temperature
continued to display in smaller windows for your reference. To return to the main operating screen touch the back 1
button.
To stop the system at the end of your recovery session there
are several ways to stop the system and close it down. You can
stop the cooling system by touching the stop system button,
in this case the pump will continue to run, however you can
stop to pump at any time by touching the stop pump button.
Alternatively you can stop everything by touching the all stop
button. Alternatively you can simply switch off the main power. If
you use the all stop button the fan may continue to run for a short
time to cool the cabinet.
Emptying the pool USING THE BUILT IN PUMP.
You can use the main circulating pump to empty the water from
the pool by detaching the top hose from the top of the pool and
directing it to a drain. The pump can be turned on and off at any
time using the pumps stop/start button.
10
14
25
detailed operation
the touch button functions
System settings
When your iCool start up, the first screen you will see offers you a system settings button. Optimum
settings are automatically selected so there usually no need to use this feature. The three settings you
can change are the fan speed range, the temperature from degrees Centigrade to Fahrenheit and the
sound level from the screen.
Main cooling fan speed. This allows you to set the main cooling fan to either normal or quiet mode.
Generally you should always leave it in the NORMAL mode which is fully automatic and allows the
system to control the fan speed to give the very best efficiency and fastest cooling.
If you are in a very quiet environment you can select quiet mode, but you must be aware that this will reduce the cooling
ability of the system, however it will be quieter overall as the fan will not run higher than 60% of maximum unless there
is a risk of overheating, in which case the safety system will turn the fan back to high no matter what the setting. The
normal setting is used to give absolute maximum cooling power where higher fan noise is not a problem. on a normal
day this gives about 25% more cooling than in the quiet mode. If cooling seems lower than normal, check to see if this
feature was previously set to Quiet Mode.
Temperature display scale: This can be set to either Centigrade
or Fahrenheit and this changes all of the displays throughout the
entire system. When you first start the iCool it will normally start in
Centigrade as this is the world standard. Due to complex decimal
calculations between Cº and Fº there may be minor difference in
the true Fº displays. This has no effect on actual cooling accuracy.
The sound level adjusts the sounds made by touching the screen
and by the alarms. Normally it should be left on high to assist with
settings and to make sure alarms are heard.
A red dot indicates which setting is selected in each of the available
settings.
OWNER’S MANUAL FOR iCOOL RECOVERY SYSTEMS
All iCool Lite Models from January 2013
iCoolsport.com
Page 9
temperature settings
When your iCool starts up, you are offered 3
different ways to choose a water temperature
setting. Whichever method you choose it
eventually takes you to the main run screen. If
you make no setting, the system will automatically
insert 15°C.(around 59ºF) In this case you would
navigate directly to the main run screen in order
to access and start the pump and cooling system.
If you want to use your previous setting from the
last session, you can touch the use previous
setting button and the last setting you used will be
automatically inserted into the system. Previous
settings may have been lost if you have removed
to mains power.
If you want to make a new setting, which is the
most common choice users make, you touch the
make new settings button and this will take you to the screen
illustrated above, where you can use the up and down arrows to
select the temperature you require. After you make your setting
touch of the start button to go to the main screen where you
can start both the pump and the cooling system and where all
relevant temperature information is clearly displayed.
10
27
water temperature setting screen
10
14
27
water temperature FULL screen
Temperature limitations
Because of the dangers of hypothermia in the case of an unattended athlete using the pool, your system
will not allow you to set temperatures below 5°C/40°F. If the model you are using is the contrast model
which also provides heating for contrast therapy you cannot set the temperature above 45°C/112°F
because of the risk of scalding. These temperature limits have been set after wide consultation with
the sporting industry around the world. There are no demonstrated benefits in using water temperature
lower than 5°C or above 45°C and therefore the risk
of doing so is not justified.
Timing functions
Your iCool offers a number of very useful timing
functions including a real-time clock, a countdown
timer to time recovery and training sessions and
a timer to shut down the system automatically at a
predetermined time after use. To set up and use
these functions touch the timer function button
on the home screen. You can reach this screen by using the back
1 button or the home button.
11:25
time setting screen
In order to use these functions you first need to set the time of day on the built-in clock.
To set the clock touch the set main clock button on the timing functions screen and the time setting display on the bottom
right of the screen will begin flashing. You must set it while one of the numbers is flashing by using the up down and
left right keys. Once you stop using these keys for more than a few seconds the display will stop flashing and the time
showing is set into the system and the clock begins operating. The iCool clock operates in the universal 24-hour time
style.
Automatic system shutdown timer
You can preset your iCool to shut down at any time up to five hours in the
future. This is very convenient for coaches and specialists who may want
to leave the training area early but want to make sure that the system is not
left running needlessly. To set this time, touch the set shut down button and
the clock digits on the bottom right of the screen will begin to flash as with
setting the clock. Use the same up down and left right arrows to set the
number of hours and minutes you wish to elapse before the system automatically shuts down. The system automatically
begins the countdown and will stop when the time you set reaches zero. The time remaining before shutdown is
displayed on the main clock display screen.
As the same arrows are used to set all three time functions, to avoid confusion, a red dot appears next to be button of
the function being set.
A very popular and useful feature of your iCool is the session countdown timer.
This allows you to accurately control the immersion times of athletes and to repeat those times as often as needed. This
is an essential part of successful cryo recovery therapy and is just as important as maintaining accurate and consistent
temperatures, which of course your iCool does perfectly.
The session timer is set up from the main time setting screen by touching the set countdown button. The numbers on
the setting screen in the bottom right-hand corner will begin to flash and you can use the left, right and up, down arrows
to change the time in minutes and seconds. Once you have set the time you want your athletes to remain in the bath,
touching the display countdown full-screen button will take you to the screen illustrated below. This screen allows you to
see the countdown from a distance and also to control it in various convenient ways. The current pool temperature and
the outside temperature will also be displayed.
The count down can be set for once only, or it can repeat automatically as many times as
you like. This is particularly convenient if you have a number of athletes using the same pool
at the same time. The system beeps for each of the last five seconds at the end of each
countdown to warn the athletes to get ready to get either in or out of the pool and pauses for
several seconds to allow the changeover before the countdown begins again (if it is set in
the repeat mode).
Resets time to the preset
value in the single shot
mode, ready to start again by
pressing the start button
When this button is pressed
the countdown will repeat
until the repeat function is
cancelled by pressing once
again. A red dot indicates that
it is active
14
2:10
You can pause the
countdown at any time
and start again from the
same position with this
button, or touch reset to
start from the top.
27
This button starts the
countdown
OWNER’S MANUAL FOR iCOOL RECOVERY SYSTEMS
All iCool Lite Models from January 2013
iCoolsport.com
Page 11
You can also display the main clock, showing the time
of day in full-screen mode if required by touching the
display clock full screen button.
To go back to the previous screen touch the
back 1 button.
External lighting
This model does not have room lighting
stereo sound system
This model does not have a sound system.
The help system
Your iCool has an extensive built-in electronic
help system. Detailed and well illustrated helpful
information on every important subject to do with
the operation of your iCool, is available from almost
any screen simply by touching the help button.
Touching any help button will take you to the screen
illustrated on the right. The screen has eight menu
buttons covering all of the important topics you are ever likely to need
assistance with.
When you touch the menu button covering the topic you need
assistance with, the screen will change to a series of pages
covering that subject. Sample screens are illustrated below and
opposite.
14
14:10
2:41
You can flip forward or backwards from page to page using the buttons on the right-hand side of the help screens or you
can return to be main help menu page at any time.
The built-in illustrated help system is a revolutionary new idea and we are constantly updating it as new information and
new feedback comes in from all over the world from iCool clients and from our recovery research programs in several
countries.
Some help pages may not be installed on your iCool when it is delivered, so that your local dealer can install them to
suit your country and sport. Alternatively iCool can provide a free update memory card with the latest help menus to
suit your needs.
If your screen locks up or displays random text while using the help menus, please restart the iCool at the main switch
to correct this.
examples of the electronic help system’s pages
You may need a free local upgrade memory card to access all help files for your region.
Locking your iCool system to prevent tampering.
Your iCool has an electronic lock.
As you can see, iCool Systems have attractive user interfaces,
this makes them easy and very intuitive to use, but the downside
is that untrained people sometimes like to play with the colourful
touchscreens. As with any sophisticated piece of equipment when
people start pressing buttons at random anything can happen. Your
iCool has many safety features to prevent a person tampering with the system from causing a disaster, but most of these
safety features involve Automatically shutting down the system which of course is undesirable. We have covered this by
installing a secret locking routine. It is a good idea to keep this secret to as few people as possible.
To lock the screen so that no further inputs can be made, touch and hold the iCool icon on the main run screen for more
than 10 seconds (you can only lock from this main screen). A picture of a lock will appear. While ever this lock is visible
it is not possible to make any inputs or to change screens.
To unlock the system and returned to normal, repeat the procedure. Touch and hold the iCool icon for more than 10
seconds. The lock will disappear and all functions will return to normal.
OWNER’S MANUAL FOR iCOOL RECOVERY SYSTEMS
All iCool Lite Models from January 2013
iCoolsport.com
Page 13
IF YOUR SCREEN FREEZES OR FAILS TO RESPOND:
As with all computers and computer controlled devices it is possible that occasionally the system could freeze due to
data or software conflicts. Your iCool has 2 computers that monitor and communicate with each other. Occasionally a
data error can cause them to stop communicating.
We have designed the system to be as fail safe as possible. In most cases if the screen freezes the main computer will
still carry on running the system and monitoring the safety features but you will not be able to change anything. You can
either allow it to keep running if that is more convenient, or you can restore the system to normal operation by switching
off the main power and re starting. Exactly as you would do if your computer or smart phone freezes.
The system will always reset to normal when you restart it.
When your screen first starts up and the welcome screen appears a small warning notice may appear in the centre of
the screen for one or two seconds referring to the inter computer communication requirements, this is normal.
emergency override provisions
Certain safety features in your icool can be overridden in the event of a partial failure. ICool systems are very reliable
and have attained an excellent reputation around the world for this. In addition we have done all that we can in the
designs to build-in ways to work around any partial failure, so that you are not prevented from using your system for an
important event. There are some circumstances in which it would be acceptable to temporarily override certain safety
systems that may become too sensitive and cause trouble until they can be properly readjusted. This allows systems
to continue to operate in circumstances where otherwise it might not be possible. Of course we do not advise the
overriding of electrical safety circuits.
For example, depending on the way your system has been set up, it sometimes occurs that the water flow monitoring
system may be too sensitive and will stop the pump because it appears that water is not flowing properly. We allow this
to be over ridden if it becomes troublesome. Instructions on how to do this will appear on the screen automatically if this
happens. It must be remembered of course that if you disarm this system the pump is no longer protected from running
dry and therefore without lubrication so it is essential that you manually monitor the water flow. Our staff can assist you
by phone or e-mail to overcome most problems on the spot.
If you use this over ride function the pump could be damaged if no water flows for more than a few minutes. Even if the
entire touchscreen user interface fails, we can usually still get you going.
In our efforts to remain the world’s number one supplier of mobile ice bath systems, we have continued to improve
reliability, but we have also engineered ways to ensure that no matter what happens in the field, in most cases you can
still use your iCool for that important event.
Realistically, even the best electronic systems occasionally have problems, especially in portable systems that have a
relatively hard life.
Fortunately, we have very few such problems, but as an added benefit we have built into all iCool’s a complete manual
override system that allows your iCool to operate effectively even if all of the main electronics fail for whatever reason.
We do not publish this over ride information in the manual because it is a little different from model to model, but in the
rare event that you ever have a failure of the electronics which prevents you from operating your iCool, just call or e-mail
us for advice. You will be contacted promptly and we will explain how to work around your problem until we can arrange
repairs. This is an important service that we hope you never need, but it’s good to know it is there.
In addition to this service you will be pleased to know that your iCool is of a modern modular design, which means that
most components can be easily replaced in the field and often by the owner.
IF THE STATUS BAR LIGHT ON TOP OF THE iCOOL TURNS RED WHEN YOU START THE COOLING CYCLE.
If the water temperature in the pool is already lower than the cooling temperature you set then the iCool will automatically
attempt to heat the water to match the temperature you have set. The red bar indicates activation of the heating mode.
No Heating can occur if your model does not have the heating option.
For safety reasons the system will not change from heating mode back to cooling mode unless you re start it by turning
the main power off and back on. For cooling, you must set a temperature that is lower than the present temperature of
the water. If you need to set a temperature that is very close to or the same as the present pool temperature start the
cooling within a few seconds after starting the pump, before the system has time to read the water temperature.
SPECIFICATIONS
LITE
COOLING POWER
2200 Watts
HEATING POWER Optional Model
2400 Watts
RUN (& Max.) POWER @220Volts
4 Amps (10Amps)
RUN (& Max.) POWER @110Volts
8 Amps (20Amp)
HEAT PUMP TYPE
Rotary
EARTH LEAK SAFETY DEVICE
STAINLESS STEEL HEAT
EXCHANGER TANK
Yes 30 Milliamps
10 plate, silver
soldered
ROLLER BEARING WHEELS
No
STAINLESS HANDLES
Yes
AREA LIGHTING
No
HI RESOLUTION COLOUR TOUCH
SCREEN
Yes 800 x 480
ELECTRICALLY ISOLATED PUMP
Yes 15 Litre (4 US
Gals) per minute
MAXIMUM PUMP CAPACITY
20 Litres (5.2 US
Gals) per minute
LOCKING POWER PLUG
3 Pin 10 Amps
Heavy Duty
WEIGHT KG / POUNDS
23KG - 50 Lbs
DIMENSIONS H. - W. - D. in mm.
240x420x300
DIMENSIONS H. - W. - D. Inches
10x16.5x11.8
OWNER’S MANUAL FOR iCOOL RECOVERY SYSTEMS
All iCool Lite Models from January 2013
iCoolsport.com
Page 15
NOTE ABOUT SPECIFICATIONS:
iCool Systems are sold all around the world and these specifications may be different for units delivered in your
country due to local conditions or regulations or other factors. Also certain specifications may change due to ongoing
research and development, because we are constantly improving our products.
We welcome your feedback and suggestions and we offer support for general enquiries and information for specific
countries on our website at.
Thank you for choosing iCool the world’s most popular ice bath therapy
and recovery systems.
Published 2013 by
iCool (Australia) Pty Ltd
iCool HK (China) Ltd.
iCool is a Regestered Trade Mark worldwide.
Contact: info@icoolsport.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising