Sony | MHC-GX8000 | User's Manual | Sony MHC-GX8000 User's Manual

4-238-409-11 (2)
Mini Hi-Fi
Component
System
Operating Instructions
GB
Owner’s Record
The model and serial numbers are located on the rear panel. Record the serial number
in the space provided below. Refer to them whenever you call upon your Sony dealer
regarding this product.
Model No.
Serial No.
MHC-GX8000/RG77
MHC-RG66T
1GB
© 2002 Sony Corporation
MHC-RG77
4-238-409-11 (2)
WARNING
WARNING
To prevent fire or shock hazard, do not
expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet.
Refer servicing to qualified personnel only.
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
This appliance is classified
as a CLASS 1 LASER
product. The CLASS 1
LASER PRODUCT
MARKING is located on
the rear exterior.
To prevent fire, do not cover the ventilation of the
apparatus with news papers, table-cloths, curtains,
etc. And don’t place lighted candles on the apparatus.
To prevent fire or shock hazard, do not place objects
filled with liquids, such as vases, on the apparatus.
Don’t throw away the battery with
general house waste, dispose of it
correctly as chemical waste.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
NOTICE FOR THE CUSTOMERS IN THE
U.S.A.
ENERGY STAR® is a U.S.
registered mark.
As an ENERGY STAR® partner,
Sony Corporation has determined
that this product meets the
ENERGY STAR® guidelines for
energy efficiency.
About this manual
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
The instructions in this manual are for
model MHC-GX8000, MHC-RG77 and
MHC-RG66T. In this manual, the MHC-RG77
is used for illustration purposes unless stated
otherwise.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
2GB
MHC-RG77
4-238-409-11 (2)
Table of Contents
List of Button Location and
Reference Pages
Main unit ............................................... 4
Remote Control ..................................... 5
Getting Started
Hooking up the system .......................... 6
Inserting two size AA (R6) batteries into
the remote ........................................ 8
Setting the clock .................................... 8
CD
Loading the CD ..................................... 9
Playing the CD
–– Normal Play/Shuffle Play/
Repeat Play ..................................... 9
Programming the CD tracks
–– Program Play ............................ 10
Tuner
Presetting radio stations ....................... 11
Listening to the radio
–– Preset Tuning ........................... 11
Tape
Loading a tape ..................................... 12
Playing a tape ...................................... 12
Recording to a tape
–– CD Synchro Recording/
High Speed Dubbing/Recording
Manually/Program Edit ................. 13
Timer-recording radio programs ......... 14
Sound Adjustment
Adjusting the sound ............................. 16
Selecting the speaker system ............... 16
Selecting the preset effect .................... 16
Adjusting the graphic equalizer and
storing the personal file ................. 17
Selecting the surround effect ............... 17
Other Features
Changing the spectrum analyzer
display ........................................... 18
Adjusting the brightness of the
display ........................................... 18
Enhancing the video game sound
— Game Sync ............................... 18
Mixing the sound
— Game Mixing ........................... 18
Singing along ....................................... 19
Falling asleep to music
— Sleep Timer .............................. 19
Waking up to music
— Daily Timer .............................. 20
Display
Turning off the display
— Power Saving Mode ................. 21
Using the display ................................. 21
Hooking Up the Optional
Components
Connecting an MD deck/VCR ............ 22
Connecting a Video Game Player ....... 22
Connecting external antennas .............. 23
Troubleshooting
Problems and remedies ........................ 24
Additional Information
Precautions .......................................... 26
Specifications ...................................... 27
MHC-RG77
3GB
4-238-409-11 (2)
List of Button Location and Reference Pages
Illustration number
How to use this page
r
Use this page to find the location of buttons and other
parts of the system that are mentioned in the text.
PLAY MODE e; (9, 10, 14)
R
R
Name of button/part
Reference page
Main unit
ALPHABETICAL ORDER
A-D
CD eg (7, 9, 10, 13, 14)
CD SYNC HI-DUB qf (13, 14)
DECK A A wh (12~14)
DECK B A qh (12~15)
DIMMER 9 (18)
DIRECTION q; (12~14)
DISC 1~3 4 (9, 10)
DISC SKIP EX-CHANGE 5 (9, 10)
Disc tray 3 (9)
DISPLAY 7 (21)
E-L
EDIT q; (14)
EFFECT ON/OFF rs (16)
ENTER ra (10, 11, 14, 15, 17, 20,
25)
FM MODE qs (11, 25)
1
23
4
GAME ea (18, 22)
GAME EQ rd (18)
GAME INPUT wd (13, 18)
GAME MIXING wl (13, 18)
GROOVE rf (16)
IR (receptor) 2
R-Z
REC PAUSE/START qg (13, 14)
REPEAT qs (10)
SPECTRUM 8 (18)
SURROUND el (17)
SURROUND SPEAKER MODE
(MHC-GX8000/RG77 only)
wj (16)
TAPE A/B ed (12, 13)
TUNER/BAND ef (11)
TUNER MEMORY e; (11)
VOLUME qa (20)
M-Q
MD (VIDEO) es (22, 24)
MIC wa (19)
MIC LEVEL w; (19)
MOVIE EQ ek (16)
MUSIC EQ eh (16)
OPEN/CLOSE Z 6 (9, 10)
P FILE r; (17)
PHONES (jack) ql (24)
PLAY MODE e; (9, 10, 14)
5
BUTTON DESCRIPTIONS
@/1 1
hH ws
x qd
X wk
> qj
. wg
M/+ qk
m/– wf
v/V/b/B ej
6
7
8
9
eg
0
ef
eh
ed
es
K
e;
wl
wk
wj
L
O
wh
qh
wg
X
qj
qk
ea
M
W
ws wa w;
ej
ek
el
rf
N
rd rs
ra r;
ql
4GB
MHC-RG77
4-238-409-11 (2)
Remote Control
A-M
P-Z
CD ql (7, 9, 10, 13, 14)
CLEAR 7 (10, 14)
CLOCK/TIMER SELECT 2
(15, 20)
CLOCK/TIMER SET 3 (8, 14,
20)
D.SKIP 9 (9)
ENTER qd (8, 10, 11, 14, 15, 17,
20)
EFFECT ON/OFF qf (16)
GAME w; (18, 22)
MD (VIDEO) q; (22)
A
Y
X
W
V
U
T
S
R
qj
qh
B
PRESET – wd (11)
PRESET + wf (11)
PRESET EQ qj (16)
P FILE qh (17)
SURROUND SPEAKER MODE
(MHC-GX8000/RG77 only) qs
(16)
SURROUND qs (17)
SLEEP 1 (19)
TAPE A/B qa (12, 13)
TUNER/BAND qk (11)
TUNING – wa (11)
TUNING + ws (11)
VOL +/– 8 (20)
BUTTON DESCRIPTIONS
@/1 4
hH wg
X5
x6
. wd
> wf
m wa
M ws
v/V/b/B qg
C
List of Button Location and Reference Pages
ALPHABETICAL ORDER
D
E
6
7
8
9
q;
qa
qs
qd
qf
qg
5GB
MHC-RG77
4-238-409-11 (2)
Getting Started
Hooking up the system
Do the following procedure 1 to 5 to hook up your system using the supplied cords and
accessories.
AM loop antenna
FM antenna
3
4
1
2
5
2
Surround
speaker (Right)
(MHC-GX8000/
RG77 only)
Front speaker
(Left)
Front speaker
(Right)
1 Connect the front speakers.
Connect the speaker cords to the SPEAKER
(MHC-RG66T)/FRONT SPEAKER
(MHC-GX8000/RG77) jacks.
Insert only the stripped portion.
R
3 Connect the FM and AM antennas.
Set up the AM loop antenna, then connect
it.
Red
L
+
Jack type A
_
AM loop antenna
Extend the FM lead
antenna horizontally.
FM
75
Red/Solid (3) Black/Stripe (#)
2 Connect the surround speaker
(MHC-GX8000/RG77 only).
Connect the speaker cords to SURROUND
SPEAKER jacks.
Insert only the stripped portion.
R
Surround
speaker (Left)
(MHC-GX8000/
RG77 only)
Blue
L
AM
Jack type B
Extend the FM lead
antenna horizontally.
AM loop antenna
FM
75
+
_
AM
Blue/Solid (3) Black/Stripe (#)
Note
GB
6
Keep the speaker cords away from the antennas to
prevent noise.
MHC-RG77
4-238-409-11 (2)
4 For models with a voltage selector, set
VOLTAGE SELECTOR to the position of
your local power line voltage.
120V
230240V
Place the front speakers at an angle of 45
degrees from your listening position.
Front
speaker
(R)
Front
speaker
(L)
Getting Started
220V
Positioning the speakers
45º
5 Connect the power cord to a wall outlet.
The demonstration appears in the display.
When you press ?/1, the system turns on
and the demonstration automatically ends.
If the supplied adaptor on the plug does not
fit your wall outlet, detach it from the plug
(only for models equipped with an adaptor).
To connect optional components
See page 22.
To attach the speaker pads
Attach the supplied speaker pads to the bottom
of the speakers to stabilize the speakers and
prevent them from slipping.
Surround
speaker
(L)
(MHC-GX8000/
RG77 only)
Surround
speaker
(R)
(MHC-GX8000/
RG77 only)
Notice for carrying this system
Do the following to protect the CD
mechanism.
1 Make sure that all discs are removed
from the unit.
2
Hold down CD and then press ?/1 until
“LOCK” appears.
3
4
Release ?/1 first, then release CD.
Unplug the AC power cord.
7GB
MHC-RG77
4-238-409-11 (2)
Inserting two size AA (R6)
batteries into the remote
AA (R6)
batteries
e
E
e
E
Tip
With normal use, the batteries should last for about
six months. When the remote no longer operates the
system, replace both batteries with new ones.
Note
If you do not use the remote for a long period of time,
remove the batteries to avoid possible damage from
battery leakage.
Setting the clock
1 Turn on the system.
2 Press CLOCK/TIMER SET on the
remote.
When you set the time for the first time,
proceed to step 5.
3 Press V or v repeatedly to select
CLOCK SET.
4 Press ENTER.
5 Press V or v repeatedly to set the hour.
6 Press ENTER.
7 Press V or v repeatedly to set the
minute.
8 Press ENTER.
The clock starts functioning.
Tip
If you have made a mistake or want to change the
time, start over from step 2.
Note
The clock settings are canceled when you disconnect
the power cord or if a power failure occurs.
8GB
MHC-RG77
4-238-409-11 (2)
CD
1 When playback is stopped, press PLAY
MODE repeatedly until the mode you
want appears in the display.
Loading the CD
1 Press OPEN/CLOSE Z.
The CD compartment slides out.
2 Place a CD with the label side up on the
To play
ALL DISCS
All CDs in the disc tray
continuously.
1 DISC
The CD you have selected in the
original order.
SHUFFLE
ALL DISCS
The tracks on all CDs in random
order.
SHUFFLE
1 DISC
The tracks on the CD you have
selected in random order.
PROGRAM
The tracks on all CDs in the
order you want them to be
played (see “Programming the
CD tracks” on page 10).
disc tray.
When you play a CD
single, place it on the
inner circle of the
tray.
To insert additional discs, press DISC SKIP
EX-CHANGE to rotate the disc tray.
3 Press OPEN/CLOSE Z to close the CD
compartment.
2 Press one of the DISC 1~3 buttons.
If you press hH when CD is selected as
the function (press CD) and the disc tray is
closed, playback starts from the selected
CD.
Playing the CD
–– Normal Play/Shuffle Play/Repeat
Play
Tip
This unit lets you play the CD in different play
modes.
Other Operations
Track
Disc tray number number
CD
Select
Playing time
You cannot change the play mode during playback.
To
Do this
Stop playback
Press x.
Pause playback
Press X.
Press again to resume
playback.
Select a track
During playback or pause,
press > (to go forward)
or . (to go back).
Find a point in a track
Press and hold down M
or m during playback and
release it at the point you
want.
Select a CD when
playback is stopped
Press one of the DISC 1~3
buttons or DISC SKIP EXCHANGE (or D. SKIP on
the remote).
Switch to CD function
from another source
Press CD or one of the
DISC 1~3 buttons
(Automatic Source
Selection).
ALL1 DISCS
Disc presence
indicator
continued
9GB
MHC-RG77
4-238-409-11 (2)
Playing the CD (continued)
4 Press . or > repeatedly until the
track you want appears in the display.
To
Do this
Play repeatedly
(Repeat Play)
Press REPEAT repeatedly to
select “REPEAT”*1 or
“REPEAT 1”*2.
Cancel Repeat
Play
Press REPEAT until
“REPEAT” or “REPEAT 1”
disappears from the display.
Disc tray
number
Track
number
Total playing time
(including selected
track)
PROGRAM
Exchange other CDs Press DISC SKIP
while playing
EX-CHANGE.
Remove the CD
Press OPEN/CLOSE Z.
5 Press ENTER.
The track(s) is (are) programmed. The
program step number appears, followed by
the total playing time.
*1
All the tracks repeated up to five times.
You cannot use this function during SHUFFLE
ALL DISCS.
*2
To repeat the current track you are playing.
Tip
6 To program additional tracks, repeat
steps 3 to 5.
Pressing the CD while the power is off automatically
turns the power on and CD is selected as a function.
Programming the CD
tracks
–– Program Play
You can make a program of up to 25 tracks
from all the CDs in the order you want them to
be played.
1 Press CD.
2 Press PLAY MODE repeatedly until
“PROGRAM” appears in the display.
Skip step 3 to select tracks from the same
disc.
7 Press hH.
To
Do this
Cancel Program Play
Press PLAY MODE
repeatedly until “1 DISC” or
“ALL DISCS” appears in
the display.
Clear a track from
the end
Press CLEAR on the remote
when playback is stopped.
Add a track to the
program when
playback is stopped
1 Press one of the DISC
1~3 buttons to select a
CD.
2 Press . or >
repeatedly to select the
track.
3 Press ENTER.
3 Press one of the DISC 1~3 to select a
CD.
To program all the tracks on a CD at once,
proceed to step 5 while “AL” appears on the
display.
Tips
• The program you made remains in the system’s
memory even after it has been played back. Press
hH to play the same program again.
• If “--.--” appears instead of the total playing time
during programming, this means:
– you have programmed a track number
which exceeds 20.
– the total playing time has exceeded 100 minutes.
10GB
MHC-RG77
4-238-409-11 (2)
Tuner
Tips
Presetting radio stations
You can preset 20 stations for FM and 10
stations for AM.
1 Press TUNER/BAND repeatedly to
• The preset stations are retained for half a day even
if you unplug the power cord or if a power failure
occurs.
• Pressing TUNER/BAND while the power is off
automatically turns the power on and TUNER is
selected as a function.
Listening to the radio
select FM or AM.
2 Press and hold M or m (or TUNING
Scanning stops when the system tunes in a
station. “TUNED” and “STEREO” (for a
stereo program) appear.
MHz
AUTO
–– Preset Tuning
Tuner
+/– on the remote) until “AUTO”
appears in the display and the
frequency indication starts to change,
then release.
Preset radio stations in the tuner's memory first
(see “Presetting radio stations”).
1 Press TUNER/BAND repeatedly to
select FM or AM.
2 Press . or > (or press PRESET
+/– on the remote) to tune in the preset
station you want.
Preset number
Frequency
3 Press TUNER MEMORY.
MHz
A preset number appears in the display.
Preset number
To listen to non-preset radio stations
4 Press . or > to select the preset
number you want to store.
5 Press ENTER.
“COMPLETE” appears in the display.
The station is stored.
6 Repeat steps 1 to 5 to store other
Press M or m (or TUNING +/– on the
remote) repeatedly (Manual Tuning) or press
and hold M or m (or TUNING +/– on the
remote) (Automatic Tuning).
Tips
• When an FM program is noisy, press FM MODE so
that “MONO” appears in the display. There will be
no stereo effect, but the reception will improve.
• To improve broadcast reception, reorient the
antennas.
stations.
To tune in a station with a weak
signal (Manual Tuning)
Press M or m (TUNING +/– on the remote)
repeatedly to tune in the station manually.
To change the AM tuning interval
(Except Middle Eastern models)
The AM tuning interval is factory set to 9 kHz
(10 kHz in some areas). To change the AM tuning
interval, select any AM station first, then turn off the
power. While holding down the ENTER button, turn
the power back on. When you change the interval,
AM preset stations will be erased. To reset the
interval, repeat the same procedure.
11GB
MHC-RG77
4-238-409-11 (2)
Tape
Loading a tape
To
Do this
Stop playback
Press x.
Pause playback
Press X.
Press again to resume
playback.
Fast-forward
Press M while playing the
front side, or press m while
playing the reverse side.
Rewind
Press m while playing the
front side, or press M while
playing the reverse side.
1 Press TAPE A/B repeatedly to select
Deck A or B.
2 Press Z on the selected deck.
3 Insert a tape in deck A or B.
Insert with the
side you want to
play/record facing
forward.
Tips
Playing a tape
1 Load a tape.
2 Press DIRECTION repeatedly to select
g to play one side, j to play both
sides or RELAY* (Relay Play) to play
both decks in succession.
3 Press hH. The tape starts playing.
Press hH again to play the reverse side.
Tape presence indicator
• During j or Relay Play, the deck stops
automatically after repeating the sequence five
times.
• Pressing TAPE A/B while the power is off
automatically turns the power on and TAPE is
selected as a function.
• When a tape (tapes) is (are) inserted, corresponding
presence indicators light up.
Searching for the beginning of a
track (AMS*)
During playback, press . or > repeatedly
for the number of songs you want to skip
forward (or backward).
The search direction, + (forward) or – (back),
and number of songs being skipped (1~9)
appear in the display.
Example: searching forward 2 songs
ALL1 DISCS
* AMS (Automatic Music Sensor)
Note
* Relay Play always follow this cyclic sequence:
Deck A (front side) t Deck A (reverse side) t
Deck B (front side) t Deck B (reverse side)
The AMS function may not operate correctly under
the following circumstances:
– When the unrecorded space between songs is less
than 4 seconds long.
– When the unit is placed near a television.
12GB
MHC-RG77
4-238-409-11 (2)
Recording to a tape
–– CD Synchro Recording/High Speed Dubbing/Recording Manually/
Program Edit
You can record from a CD, tape, radio or other connected component. The recording level is adjusted
automatically.
Steps
Recording from a CD
(CD Synchro Recording)
Recording from a tape
(High-Speed Dubbing)
Recording Manually
Insert a recordable tape into deck B.
2
Press CD.
Press TAPE A/B repeatedly Press a function button
to select TAPE A.
for the recording source.
3
Load the CD you want to
record.
Load the tape you want to
record into deck A.
4
Press CD SYNC HI-DUB.
Tape
1
Load the CD or tape
(or other audio
sources), or tune to the
station you want to
record.
Press REC PAUSE/
START.
DECK B stands by for recording.
REC PAUSE/START indicator flashes.
5
Press DIRECTION repeatedly to select g to record on one side.
Select j (or RELAY) to record on both sides.
6
Press REC PAUSE/START. If you are recording manually, press hH to start
playing the source (for CD or Tape).
Recording starts.
7
Press x to stop recording.
Tips
• When you record on both sides, be sure to start
from the front side. If you start from the reverse
side, recording stops at the end of the reverse side.
• For recording from the reverse side:
After step 1, press TAPE A/B to select deck B and
press hH twice to start playback of the reverse
side. Press x at the point where you want to start
recording. The TAPE B reverse side indicator lights
up.
• (High-Speed Dubbing only)
If you set direction to j when the tapes you use
have different lengths, the tapes in each deck
reverses independently. If you select RELAY, the
tapes in both decks reverse together.
• For recording from the radio:
If noise is heard while recording from the radio,
move the respective antenna to reduce the noise.
• For recording from a CD to a tape manually:
You can press . or > to select tracks during
recording pause mode (after step 4 and before step
6).
• You can mix the sound from the component
connected to the GAME INPUT jacks with another
function such as CD, tape, radio or an MD
connected to this system. To record the mixed
sound, press GAME MIXING after step 4 of
“Recording Manually” and then press REC
PAUSE/START to start recording. Game Mixing
does not function during High-Speed Dubbing and
CD Synchro Recording.
Note
You cannot listen to other sources while recording.
continued
13GB
MHC-RG77
4-238-409-11 (2)
Recording to a tape (continued)
To
Do This
Cancel Program Edit
Press PLAY MODE
repeatedly until “1 DISC” or
“ALL DISCS” appears in
the display.
— Program Edit
Clear a track from
the end
Press CLEAR on the remote
when playback is stopped.
You can record tracks from all the CDs in the
order you want. When programing, make sure
the playing times for each side do not exceed
the length of one side of the tape.
Tip
Recording a CD by specifying
track order
1 Insert a recordable tape into deck B,
then press CD.
2 Press PLAY MODE repeatedly until
“PROGRAM” appears in the display.
3 Press one of the DISC 1–3 button to
To check the required tape length for recording a CD,
press EDIT after you have loaded a CD and pressed
CD. The required tape length for the currently
selected CD appears, followed by the total playing
time for side A and side B respectively (Tape Select
Edit).
Note
You cannot use Tape Select Edit for discs containing
over 20 tracks.
select a CD.
To program all the tracks on a CD at once,
proceed to step 6 while “AL” appears in the
display.
4 Press . or > repeatedly until the
tracks you want appears in the display.
5 Press ENTER.
The track(s) is (are) programmed. The
program step number appears, followed by
the total playing time.
6 To program additional tracks, repeat
steps 3 to 5.
Skip step 3 to select tracks from the same
disc.
7 Press CD SYNC HI-DUB.
Deck B standby for recording. The REC
PAUSE/START indicator flashes.
8 Press DIRECTION repeatedly to select
g to record on one side. Select j
(or RELAY) to record on both sides.
9 Press REC PAUSE/START.
Recording starts.
Timer-recording radio
programs
To timer-record, you must preset the radio
station (see “Presetting radio stations” on
page 11) and set the clock (see “Setting the
clock” on page 8) beforehand.
1 Tune in the preset radio station (see
“Listening to the radio” on page 11).
2 Press CLOCK/TIMER SET on the
remote.
“DAILY1 SET” appears.
3 Press V or v repeatedly to select “REC
SET”, then press ENTER.
“ON” appears and the hour indication flash
in the display.
4 Set the time to start recording.
Press V or v repeatedly to set the hour, then
press ENTER.
The minute indication starts flashing.
Press V or v repeatedly to set the minute,
then press ENTER.
The hour indication flashes again.
14GB
MHC-RG77
4-238-409-11 (2)
5 Set the time to stop recording following
the above procedure.
The start time appears, followed by the stop
time, the preset radio station to be recorded
(e.g., “TUNER FM 5”), then the original
display appears.
6 Insert a recordable tape into deck B.
Make sure the tape is in forward direction.
7 Turn off the power.
When the recording starts, the volume level
is set to the minimum.
Do this
Check the setting
Press CLOCK/TIMER
SELECT on the remote and
press V or v repeatedly to
select “REC SEL”. Then, press
ENTER.
Change the setting
Start from step 1.
Cancel timer
operation
Press CLOCK/TIMER
SELECT on the remote and
press V or v repeatedly to
select “TIMER OFF”. Then,
press ENTER.
Tape
To
Notes
• If the power is on at the preset time, the Timer
recording does not work.
• The power turns on 15 seconds before the preset
time.
15GB
MHC-RG77
4-238-409-11 (2)
Sound Adjustment
Adjusting the sound
You can reinforce the bass and create a more
powerful sound.
Selecting the preset
effect
Press GROOVE.
Press MUSIC EQ, MOVIE EQ or GAME EQ
(or PRESET EQ on the remote) repeatedly to
select the preset effect you want.
Each time you press this button, the display
changes cyclically as follows:
The preset effect name appears in the display.
See the chart “Preset effect options”.
GROOVE t V-GROOVE t GROOVE OFF
To cancel the effect
GROOVE
The volume switches to power mode and the
equalizer curve changes.
V-GROOVE
The volume switches to power mode, the low
base frequencies are powerfully reinforced, and
the equalizer curve changes.
Selecting the speaker
system
(MHC-GX8000/RG77 only)
You can enjoy different sounds when you
select the surround speaker mode.
Press SURROUND SPEAKER MODE to
select the surround speaker mode you
want.
LINK : Reproduces the same sound with the
different output level.
Press EFFECT ON/OFF repeatedly until
“EFFECT OFF” appears.
Preset effect options
“SUR ” appears if you select an effect with
surround effects.
MENU
button
Effect
For
MUSIC
EQ
ROCK
POP
JAZZ
DANCE
SOUL
ORIENTAL*
standard music
sources.
MOVIE
EQ
ACTION
DRAMA
MUSICAL
soundtracks and
special listening
situations.
GAME
EQ
ARCADE
RACING
ADVENTURE
Play station 1, 2 and
other video game
music sources.
* CLASSIC for Latin and North American models
only.
MATRIX SUR : Reproduces a wide range of
sound that actually can sense the size of the
room.
16GB
MHC-RG77
4-238-409-11 (2)
Adjusting the graphic
equalizer and storing a
personal file
You can adjust the sound by raising or
lowering the level of specific frequency band,
then store up to three personal files (P FILE) in
the memory.
Selecting the surround
effect
Press SURROUND.
Each time you press the button, the display
changes as follows:
SURROUND ON ( SUR )
Y
Before operation, select the preset effect you
want for your basic sound.
1 Press b or B repeatedly to select a
Frequency band
Note
When you choose other sound effects, the surround
effect may be cancelled.
Sound Adjustment
frequency band or surround, then
press v or V to adjust the level or
select the surround effect.
SURROUND OFF
Frequency level
2 Press and hold P FILE until the
personal file number appears in the
display.
3 Press v or V or B or b to select the
personal file number (P FILE) where
you want to store the equalizer setting.
4 Press ENTER.
The setting is automatically stored as the
personal file you selected in step 3. The
previous setting stored at this memory
location is erased and replaced by the new
setting.
To call up the personal file
Press P FILE repeatedly until the personal file
number you want appears in the display.
Tip
If you do not want to store a personal file, press
ENTER after step 1.
17GB
MHC-RG77
4-238-409-11 (2)
Other Features
Changing the spectrum
analyzer display
Press SPECTRUM.
Each time you press the button, the display
changes cyclically as follows:
SPECTRUM 1 t SPECTRUM 2 t
SPECTRUM 3 t PATTERN 1 t
PATTERN 2 t PATTERN 3 t
PATTERN OFF
Adjusting the brightness
of the display
Mixing the sound
— Game Mixing
You can mix the sound from the component
connected to the GAME INPUT jacks with
another function such as CD, tape, radio or
an MD connected to this system.
1 Select source sound you want.
2 Press GAME MIXING.
Each time you press the button, the level of
the game sound changes cyclically as
follows:
MIXING LOW t MIXING MID t
MIXING HIGH t MIXING OFF
Tips
Press DIMMER.
Each time you press the button, the display
changes cyclically as follows:
DIMMER 1 t DIMMER 2 t DIMMER 3
Enhancing the video game
sound
— Game Sync
• To record the mixed sound, press GAME MIXING
after step 4 of “Recording Manually” on page 13
and then press REC PAUSE/START to start
recording.
• The GAME MIXING indicator lights up while
Game Mixing is activated and it will remain active
while the power is on even if the function is
changed.
Notes
• Game Mixing is cancelled when you press REC
PAUSE/START.
• Game Mixing does not function during High Speed
Dubbing and CD Synchro Recording.
You need to connect a video game player
(see “Connecting a Video Game Player” on
page 22).
Press GAME.
Tips
• In standby mode, the system automatically turns on.
• The previously selected GAME EQ is automatically
selected.
• This operation cannot be performed in the Power
Saving Mode.
18GB
MHC-RG77
4-238-409-11 (2)
Singing along
You can sing along with any stereo CD or
Tape. You need to connect an optional
microphone.
1 Turn MIC LEVEL to MIN to turn down
the microphone volume.
2 Connect an optional microphone to MIC
jack.
3 Start playing the music and adjust the
volume.
4 Adjust the microphone volume by
Falling asleep to music
— Sleep Timer
You can set the system to turn off at a preset
time, so you can fall asleep to the music.
Press SLEEP on the remote.
Each time you press the button, the minute
display (the turn-off time) changes as follows:
AUTO* t 90 t 80 t 70 t … t 10 t
OFF
* The power turns off when the current CD or tape
finishes playback (for up to 100 minutes).
turning MIC LEVEL.
Turn MIC LEVEL to MIN and disconnect the
microphone from MIC jack.
Tips
• You can mix and record sound from microphone
after step 2. To record the sound see “Recording
Manually” on page 13. To stop recording, press x.
• If acoustic feedback (howling) occurs, move the
microphone away from the speakers or change the
direction of the microphone.
• If you want to record your voice through the
microphone only, you can do so by selecting the
CD function and not playing a CD.
• When high level sound signals are input, the unit
automatically adjust the recording level to prevent
distortion of the recorded sound signals (Auto
Level/ Control Function).
To
Do this
Check the remaining
time
Press SLEEP once.
Change the time to turn
off
Press SLEEP
repeatedly to select the
time you want.
Cancel the Sleep Timer
Press SLEEP
repeatedly until
“SLEEP OFF” appears.
Other Features
After you have finished.
Note
The microphone does not function during High Speed
Dubbing.
19GB
MHC-RG77
4-238-409-11 (2)
Waking up to music
8 Press ENTER.
The type of timer (“DAILY1” or
“DAILY2”), followed by the start time, stop
time and the music source appears, then the
original display appears.
— Daily Timer
You can wake up to music at a preset time
every day. Make sure you have set the clock
(see “Setting the clock” on page 8).
9 Turn off the power.
1 Prepare the music source you want to
To
Do this
Check the setting
Press CLOCK/TIMER
SELECT on the remote and
press V or v repeatedly to
select the respective mode
(“DAILY1” or “DAILY2”),
then press ENTER.
Change the setting
Start from step 1.
Cancel the timer
operation
Press CLOCK/TIMER
SELECT on the remote and
press V or v repeatedly to
select “TIMER OFF”, then
press ENTER.
play.
• CD: Load a CD. To start from a specific
track, make a program (see “Programming
the CD tracks” on page 10).
• Tape: Load a tape with the side you want
to play facing forward.
• Radio: Tune in the preset station you
want (see “Listening to the radio” on page
11).
2 Adjust the volume.
3 Press CLOCK/TIMER SET on the
remote.
“DAILY1 SET” appears.
4 Press V or v repeatedly to select
“DAILY1 SET (or DAILY2 SET)”, then
press ENTER.
Tip
The power turns on 15 seconds before the preset time.
Note
If the power is on at the preset time, the Daily Timer
does not work.
“ON” appears and the hour digits flash in
the display.
5 Set the time to start playback.
Press V or v repeatedly to set the hour,
then press ENTER.
The minute indication flashes.
Press V or v repeatedly on the remote to
set the minute, then press ENTER.
The hour indication flashes again.
6 Set the time to stop playback following
step 5 above.
7 Press V or v repeatedly until the music
source you want appears.
The indications change as follows:
t TUNER y CD PLAY T
t TAPE PLAY T
20GB
MHC-RG77
4-238-409-11 (2)
Display
Using the display
Turning off the display
— Power Saving Mode
You can check the remaining time of the
current track or that of the CD.
The demonstration display (the display changes
and the indicators flash even when the system
is turned off) and the clock display can be
turned off to minimize the amount of power
consumed during standby mode (Power Saving
Mode).
When a CD TEXT disc is loaded, you can
check the information stored on the disc, such
as the titles. When the unit detects CD TEXT
discs, the “CD-TEXT” indication appears in
the display.
Press DISPLAY repeatedly while the
system is turned off until the
demonstration display or the clock display
disappears.
Each time you press the button, the display
changes cyclically as follows:
To cancel Power Saving Mode
Press DISPLAY once to show the
demonstration, twice to show the clock
display.
Demonstration t Clock* t Power Saving
Mode
* “--.-- ” appears in the display if you have not set the
clock.
Tips
• The @/1 indicator lights up even in Power Saving
Mode.
• The timer continues to operate in Power Saving
Mode.
• During Power Saving Mode, the following
functions do not work:
— Setting the time.
— Changing the AM tuning interval.
— Pressing a function button to turn the power on.
— Switching the function of MD (VIDEO).
During normal playback
Playing time of the current track t Remaining
time of the current track t Remaining time of
the current CD (“1 DISC” mode) or “--.-- ”
display (“ALL DISCS” mode) t Title name
of the current track1) t Clock display (for
eight seconds) t Effect status
Display
Each time you press the button, the system
changes cyclically as follows:
Press DISPLAY.
When playback is stopped
When the CD player is in program mode and
there is a program:
The last track number of the program and the
total playing time2) t Total number of
programmed tracks (for eight seconds)3) t
Title name of the CD1) t Clock display (for
eight seconds) t Effect status
In other conditions:
Total number of tracks and the total playing
time t Title name of the CD1) t Clock
display (for eight seconds) t Effect status
1)
2)
3)
With CD TEXT discs only (certain characters
cannot be displayed). Depending on the disc,
some CD TEXT information may not appear.
“--.-- ” appears in the following cases:
– when the CD contains 21 tracks or more,
and the track number which exceeds 20 is
selected.
– when the program time exceeds 100 minutes.
“CD NO STEP” appears in the display if there is
no program track.
21GB
MHC-RG77
4-238-409-11 (2)
Hooking Up the Optional Components
Connecting an MD deck
or VCR
You can connect your MD deck or VCR to this
system. Be sure to match the color of the plugs
and the connectors.
Optical cover holder
Connecting a Video Game
Player
You can enjoy the video games with audio
emphasis by connecting a video game player.
To the audio and video output of your
video game player.
To the
DIGITAL IN
jack of your
MD deck
To the audio
output of your
MD deck/VCR
To
Do This
Make a digital
recording from
CD to MD
Connect an optional optical
cable.
Listen to the analog
Press MD (VIDEO).
sound of a connected
MD deck
Listen to the
connected VCR
Hold down MD (VIDEO) and
press @/1 while the power is
on. Release @/1 first, then
release MD (VIDEO). This
switches the function from
MD to VIDEO. Once you
switched to the VIDEO
function, just press MD
(VIDEO).
Tip
When you remove the optical cover, keep it at the
optical cover holder provided.
To the video input of your TV
To
Do this
Listen to the sound
of a connected
video game player
Press GAME (or GAME on
the remote).
Select the preset effect (See “Selecting the preset
effect” on page 16)
Notes
Note
• Pressing the MD (VIDEO) while the power is off
automatically turns the power on and MD is
selected as a function.
• If the sound is distorted or too loud when VIDEO
function is selected, or you want to switch back to
MD function, repeat the operation described above
to switch to MD function.
Pressing GAME while the power is off automatically
turns the power on and GAME is selected as a
function. The equalizer also switches to GAME EQ
and the previously selected effect is restored.
22GB
MHC-RG77
4-238-409-11 (2)
Connecting external
antennas
Connect an external antenna to improve the
reception.
FM antenna
Connect an optional FM external antenna. You
can also use the TV antenna instead.
FM
75
AM
AM antenna
Hooking Up the Optional Components
Connect a 6 to 15 meter (20 to 50 feet)
insulated wire to the AM antenna terminal.
Leave the supplied AM loop antenna
connected.
Insulated wire (not supplied)
FM
75
AM
23GB
MHC-RG77
4-238-409-11 (2)
Troubleshooting
“-- --:-- --” appears in the display.
Problems and remedies
If you run into any problem using this unit, use
the following check list.
First, check that the power cord is connected
firmly and the speakers are connected correctly
and firmly.
Should any problem persist, consult your
nearest Sony dealer.
General
• A power interruption occurred. Set the clock and
timer settings again.
The timer does not function.
• Set the clock correctly.
• You cannot activate the Daily timer and Timerrecording simultaneously.
“DAILY1 SET”, “DAILY2 SET”, and “REC SET”
do not appear when you press the CLOCK/
TIMER SET button.
• Set the timer correctly.
• Set the clock.
The remote does not function.
The display starts flashing as soon as you plug
in the power cord even though you haven’t
turned on the power.
The demonstration mode started. Press @/1. (see
step 5 on page 7)
The clock/timer setting is canceled.
• The power cord is disconnected or a power
failure occurs. Redo “Setting the clock”
(on page 8). If you have set the timer, redo
“Waking up to music” (on page 20) and
“Timer-recording radio programs” (on page 14).
The radio presetting is canceled.
• The power cord is disconnected or a power
failure occurs for longer than half a day. Redo
“Presetting radio stations” (on page 11).
There is no sound.
• Turn VOLUME clockwise.
• The headphones are connected to the PHONES
jack.
• Insert only the stripped portion of the speaker
cord into the SPEAKER jack. Inserting the vinyl
portion of the speaker cord will obstruct the
speaker connections.
• The protective device on the amplifier has been
activated because of short circuit. (“PROTECT”
and “PUSH POWER” flash alternately.) Turn off
the unit, eliminate the short-circuit problem and
turn on the power again.
• There is no audio output during TimerRecording.
There is severe hum or noise.
• A TV or VCR is placed too close to the unit.
Move the unit away from the TV or VCR.
• There is an obstacle between the remote and the
system.
• The remote is not pointing in the direction of the
unit’s sensor.
• The batteries have run down. Replace the
batteries.
There is acoustic feedback.
• Decrease the volume level.
• Move the microphone away from the speakers or
change the direction of the microphone.
The color irregularity on a TV screen persists.
• Turn off the TV set once, then turn it on after 15
to 30 minutes. If the color irregularity still
persists, place the speakers farther away from the
TV set.
“PROTECT”and “PUSH POWER” appear
alternately.
• A strong signal is input. Turn off the power,
leave the system turned off for a while, then turn
on the power again. If “PROTECT” and “PUSH
POWER” still appear alternately check the
speaker cords.
Speakers
Sound comes from only one channel or
unbalanced left and right volume.
• Check the speaker connection and speaker
placement.
Sound lacks bass.
• Check that the speaker’s + and – terminals are
connected correctly.
The sound from the component connected to the
MD (VIDEO) jacks is distorted.
24GB
• If “VIDEO” appears in the display when you
press MD (VIDEO), switch to “MD” function
(see “Note: Connecting an MD deck/VCR” on
page 22).
MHC-RG77
4-238-409-11 (2)
CD Player
Tuner
The disc tray does not open and “LOCKED”
appears on the front panel display.
There is severe hum or noise (“TUNED” or
“STEREO” flashes in the display).
• Contact your Sony dealer or local authorized
Sony service facility.
The disc tray does not close.
• The CD is not placed properly.
The CD does not play.
•
•
•
•
The CD is not lying flat in the disc tray.
The CD is dirty.
The CD is inserted label side down.
Moisture condensation has built up. Remove the
CD and leave the system turned on for about an
hour until the moisture evaporates.
Playback does not start from the first track.
• The player is in Program Play or Shuffle Play
mode. Press PLAY MODE repeatedly until
“1 DISC” or “ALL DISCS” appears.
“OVER” is displayed.
• You have reached the end of the CD. Press m.
• Adjust the antenna.
• The signal is too weak. Connect an external
antenna.
A stereo FM program cannot be received in
stereo.
• Press FM MODE so that “MONO” disappears.
If other troubles not described above
occur, reset the system as follows:
1 Press x, ENTER and ?/1 at the same
time.
2 Unplug the power cord.
3 Plug the power cord back in.
4 Press ?/1 to turn on the power.
The unit is reset to factory settings. All the
settings are cleared.
Troubleshooting
Tape Deck
The tape does not record.
• The tab has been removed from the cassette,
cover the broken tab with adhesive tape.
• The tape has reeled to the end.
The tape does not record nor play or there is a
decrease in sound level.
• The heads are dirty. (See “Cleaning the tape
heads” on page 26).
• The record/playback heads are magnetized. (See
“Demagnetizing the tape heads” on page 26).
The tape does not erase completely.
• The record/playback heads are magnetized. (See
“Demagnetizing the tape heads” on page 26).
There is excessive wow or flutter, or the sound
drops out.
• The capstans or pinch rollers are dirty. (See
“Cleaning the tape heads” on page 26).
Noise increases or the high frequencies are erased.
• The record/playback heads are magnetized. (See
“Demagnetizing the tape heads” on page 26).
25GB
MHC-RG77
4-238-409-11 (2)
Additional Information
Notes on CDs
Precautions
On operating voltage
Before operating the unit, check that the operating
voltage of your unit is identical with the voltage of
your local power supply.
On safety
• The unit is not disconnected from the AC power
source (mains) as long as it is connected to the wall
outlet, even if the unit itself has been turned off.
• Unplug the unit from the wall outlet (mains) if it is
not to be used for an extended period of time. To
disconnect the cord (mains lead), pull it out by the
plug. Never pull the cord itself.
• Should any solid object or liquid fall into the
component, unplug the unit and have the
component checked by qualified personnel before
operating it any further.
• The AC power cord must be changed only at the
qualified service shop.
On placement
• Place the unit in a location with adequate
ventilation to prevent heat build-up in the unit.
• Do not place the unit in an inclined position.
• Do not place the unit in locations where it is:
— extremely hot or cold
— dusty or dirty
— very humid
— vibrating
— subject to direct sunlight
On heat buildup
• Although the unit heats up during operation, this is
not a malfunction.
• Place the unit in a location with adequate
ventilation to prevent heat build-up in the unit.
If you use this unit at a large volume, the cabinet
temperature of the top, side and bottom rises
considerably. To avoid burning yourself, do not touch
the cabinet.
To prevent a malfunction, do not cover the ventilation
hole for the cooling fan.
On operation
• If the unit is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture
may condense on the lens inside the CD player.
Should this occur, the unit will not operate properly.
Remove the CD and leave the unit turned on for
about an hour until the moisture evaporates.
• When you move the unit, take out any discs.
If you have any questions or problems concerning
your unit, please consult your nearest Sony dealer.
• Before playing, clean the CD with a cleaning cloth.
Wipe the CD from the center out.
• Do not use solvents.
• Do not expose the CD to direct sunlight or heat
sources.
• Discs with non-standard shapes (e.g., heart, square,
star) cannot be played on this unit. Attempting to do
so may damage the unit. Do not use such discs.
Note on CD-R/CD-RW playback
Discs recorded on CD-R/CD-RW drives may not be
played back because of scratches, dirt, recording
conditions or the drive's characteristics. Besides, the
discs which are not yet finalized at the end of
recording, cannot be played back.
Cleaning the cabinet
Use a soft cloth slightly moistened with mild
detergent solution.
To save a tape permanently
To prevent a tape from being accidentally recorded
over, break off the cassette tab. Refer to the
instructions of the tape.
Before placing a cassette in the tape
deck
Take up any slack in the tape. Otherwise the tape may
get entangled in the parts of the tape deck and become
damaged.
When using a tape longer than 90
minutes
The tape is very elastic. Do not change the tape
operations such as play, stop, and fast-winding etc.
frequently. The tape may get entangled in the tape
deck.
Cleaning the tape heads
Clean the tape heads after every 10 hours of use.
Make sure to clean the tape heads before you start an
important recording or after playing an old tape. Use
separately sold dry-type or wet-type cleaning cassette.
For details, refer to the instructions of the cleaning
cassette.
Demagnetizing the tape heads
Demagnetize the tape heads and the metal parts that
have contact with the tape every 20 to 30 hours of use
with a separately sold demagnetizing cassette. For
details, refer to the instructions of the demagnetizing
cassette.
26GB
MHC-RG77
4-238-409-11 (2)
Specifications
AUDIO POWER SPECIFICATIONS
(MHC-GX8000 USA model only)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 6-ohm loads, both channels driven, from
120 Hz - 10 kHz; rates 200 watts per channel
minimum RMS power, with no more than 10%
total harmonic distortion from 250 miliwatts to
rated output.
Amplifier section
MHC-GX8000
Total harmonic distortion
Less than 0.1 % (6 ohms
at 1 kHz, 100 W)
Outputs
VIDEO OUT:
(phono jacks)
max. output level 1 Vp-p,
unbalanced, Sync.
negative load impedance
75 ohms
PHONES:
accepts headphones of
(stereo mini jack)
8 ohms or more
FRONT SPEAKER:
accepts impedance of 6 to
16 ohms
SURROUND SPEAKER: accepts impedance of
(MHC-GX8000/RG77
24 ohms or more
only)
System
Compact disc and digital
audio system
Laser
Semiconductor laser
(λ=795nm)
Laser Output
Max. 44.6 µW*
*This output is the value
measured at a distance of
200 mm from the
objective lens surface on
the Optical Pick-up Block
with 7 mm aperture.
Frequency response
2 Hz – 20 kHz (±0.5 dB)
Wave length
795 nm
CD OPTICAL DIGITAL OUT
(Square optical connector jack, rear panel)
Wave length
660 nm
Output Level
–18 dBm
Tape player section
Recording system
Frequency response
Wow and flutter
4-track 2-channel stereo
50 – 13,000 Hz (±3 dB),
using Sony TYPE I
cassette
±0.15% W.Peak (IEC)
0.1% W.RMS (NAB)
±0.2% W.Peak (DIN)
Tuner section
FM stereo, FM/AM superheterodyne tuner
Additional Information
MHC-RG77
The following are measured at AC 120, 220, 240V
50/60 Hz
DIN power output (rated) 160 + 160 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
200 + 200 watts
(6 ohms at 1 kHz,
10% THD)
MHC-RG66T
The following are measured at AC 120, 220, 240V
50/60 Hz
DIN power output (rated) 100 + 100 watts
(6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference)
145 + 145 watts
(6 ohms at 1 kHz,
10% THD)
Inputs
GAME (VIDEO):
1 Vp-p, 75 ohms
(phono jack)
GAME (AUDIO):
Voltage 250 mV,
(phono jacks)
impedance 47 kilohms
MD/VIDEO (AUDIO) IN: voltage 450 mV/250 mV,
(phono jacks)
impedance 47 kilohms
MIC:
sensitivity 1 mV,
(phone jack)
impedance 10 kilohms
CD player section
FM tuner section
Tuning range
Antenna
Antenna terminals
Intermediate frequency
87.5 – 108.0 MHz
FM lead antenna
75 ohm unbalanced
10.7 MHz
AM tuner section
Tuning range
Latin and North American models:
530 – 1,710 kHz
(with the interval set at 10
kHz)
531 – 1,710 kHz
(with the interval set at 9
kHz)
Middle Eastern models: 531 – 1,602 kHz
(with the interval set at 9
kHz)
Other models:
531 – 1,602 kHz
(with the interval set at 9
kHz)
530 – 1,710 kHz
(with the interval set at 10
kHz)
Antenna
AM loop antenna
Antenna terminals
External antenna terminal
Intermediate frequency
450 kHz
continued
27GB
MHC-RG77
4-238-409-11 (2)
Specifications (continued)
Speaker
Front speaker SS-RG88
Speaker system
3-way, 3-unit,
bass-reflex type
Speaker units
Super Woofer:
15 cm, cone type
Woofer:
15 cm, cone type
Tweeter:
5 cm, cone type
Nominal impedance
6 ohms
Dimensions (w/h/d)
Approx. 250 x 395 x
310 mm
Mass
Approx. 6.2 kg net per
speaker
Surround speaker SS-RS88 for MHC-GX8000/
RG77
Speaker system
2 way, 2 unit,
bass-reflex type
Speaker units
Woofer
13 cm, cone type
Tweeter
5 cm, cone type
Nominal impedance
24 ohms
Approx. 175 x 360 x 260
Dimensions (w/h/d)
mm
Mass
Approx. 3.4 kg net per
speaker
General
Power requirements
North America and Mexican models:
120 V AC, 60 Hz
Argentina/Thailand models:
220 V AC, 50/60 Hz
Other models:
120 V, 220 V or 230 - 240
V AC, 50/60 Hz
Adjustable with voltage
selector
Power consumption
MHC-GX8000/RG77
MHC-RG66T
240 watts
230 watts
Dimensions (w/h/d)
HCD-GX8000/RG77/RG66T
Approx. 280 x 360 x 445
mm
Mass :
HCD-GX8000/RG77/RG66T
Approx. 11.0 kg
Supplied accessories:
AM loop antenna (1)
Remote commander (1)
Batteries (2)
FM lead antenna (1)
Front speaker pads (8)
Surround speaker pads (8)
(MHC-GX8000/RG77
only)
Design and specifications are subject to change
without notice.
28GB
Sony Corporation
Printed in Malaysia
MHC-RG77
4-238-409-11 (2)
Download PDF