Sony | CMT-BX50BTi | User's Manual | Sony CMT-BX50BTi User's Manual

Sony CMT-BX50BTi User's Manual
3-293-642-12(1)
Micro HI-FI
Component
System
Operating Instructions
CMT-BX50BTi
© 2008 Sony Corporation
WARNING
To reduce the risk of fire or
electric shock, do not expose
this apparatus to rain or
moisture.
CAUTION
The use of optical instruments with this
product will increase eye hazard.
Notice for the customers in the
U.S.A.
The following CAUTION marking is
located on the rear exterior.
Owner’s Record
The model and serial numbers are located
on the rear of the unit. Record these
numbers in the space provided below.
Refer to them whenever you call upon
your Sony dealer regarding this product.
Model No.
Serial No.
Note to CATV system installer:
This reminder is provided to call the
CATV system installer’s attention to
Article 820-40 of the NEC that provides
guidelines for proper grounding and, in
particular, specifies that the cable ground
shall be connected to the grounding
system of the building, as close to the point
of cable entry as practical.
The following FCC statement applies
only to the version of this model
manufactured for sale in the U.S.A.
Other versions may not comply with
FCC technical regulations.
This symbol is intended
to alert the user to the
presence of uninsulated
“dangerous voltage” within
the product’s enclosure
that may be of sufficient
magnitude to constitute
a risk of electric shock to
persons.
This symbol is intended
to alert the user to the
presence of important
operating and maintenance
(servicing) instructions in
the literature accompanying
the appliance.
GB
NOTE:
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used
in accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
 Reorient or relocate the receiving
antenna.
 Increase the separation between the
equipment and receiver.
 Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
 Consult the dealer or an experienced
radio/TV technician for help.
CAUTION
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
This equipment must not be co-located or
operated in conjunction with any other
antenna or transmitter.
This equipment complies with FCC
radiation exposure limits set forth for
uncontrolled equipment and meets the
FCC radio frequency (RF) Exposure
Guidelines in Supplement C to OET65.
This equipment has a very low RF energy
level that is deemed to comply with FCC
radio frequency (RF) Exposure Guidelines
in Supplement C to OET65 without
maximum permissive exposure evaluation
(MPE).
This equipment is desirable that it should
be installed and operated with at least
20cm and more between the radiator and
person’s body (excluding extremities:
hands, wrists, feet and ankles).
Notice for the customers in Canada
Operation is subject to the following
two conditions: (1) this device may not
cause interference, and (2) this device
must accept any interference, including
interference that may cause undesired
operation of this device.
This equipment complies with IC radiation
exposure limits set forth for uncontrolled
equipment and meets the RSS-102 of the
IC radio frequency (RF) Exposure rules.
This equipment has a very low RF energy
level that is deemed to comply with
RSS-102 without maximum permissive
exposure evaluation (MPE).
This equipment is desirable that it should
be installed and operated with at least
20cm and more between the radiator and
person’s body (excluding extremities:
hands, wrists, feet and ankles).
Note on DualDiscs
A DualDisc is a two sided disc product
which mates DVD recorded material on
one side with digital audio material on
the other side. However, since the audio
material side does not conform to the
Compact Disc (CD) standard, playback on
this product is not guaranteed.
Music discs encoded with copyright
protection technologies
This product is designed to playback
discs that conform to the Compact Disc
(CD) standard. Recently, various music
discs encoded with copyright protection
technologies are marketed by some
record companies. Please be aware that
among those discs, there are some that
do not conform to the CD standard and
may not be playable by this product.
The Bluetooth word mark and logos
are owned by the Bluetooth SIG, Inc.
and any use of such marks by Sony
Corporation is under license. Other
trademarks and trade names are those
of their respective owners.
MPEG Layer-3 audio coding
technology and patents licensed from
Fraunhofer IIS and Thomson.
iPod is a trademark of Apple Inc.,
registered in the U.S. and other
countries.
GB
Table of Contents
Guide to parts and controls.............. 5
Information on the display................ 9
Getting Started
Hooking up the system
securely...................................................10
Setting the clock.................................12
Basic Operations
Playing a CD/MP3 disc......................13
Listening to the radio........................14
Using the Bluetooth function.........15
Playing the iPod...................................21
Using optional audio
components..........................................23
Adjusting the sound..........................23
Changing the display........................24
Other Operations
Creating your own program
(Program Play)......................................25
Presetting radio stations..................26
Using the Timers..................................27
GB
Others
Troubleshooting..................................29
Messages................................................33
Precautions............................................34
Specifications.......................................36
Bluetooth wireless technology......38
Compatible devices
with this system...................................40
This manual mainly explains operations using the remote, but the same operations can
also be performed using the buttons on the unit having the same or similar names.
Unit (HCD-BX50BTi/Compact Disc Receiver)
Front panel
Guide to parts and controls
Guide to parts and controls
Top panel
Continued

GB
Remote (RM-AMU009)

BLUETOOTH button (page 17, 19,
20)
Press to make a connection,
disconnection, or pairing with a
Bluetooth device.

BLUETOOTH indicator (page 19,
20)
Lights up when the Bluetooth function
is active.

 (open/close) button (page 13)
Press to open or close the disc tray.

AUDIO IN jack (page 23)
Connect to an optional audio
component.

PHONES jack

/ (power) button (page 12, 27,
32)
Press to turn on the system.

STANDBY indicator (page 24, 29)
Lights up when the system is turned off.

Remote sensor (page 29)
GB
Connect the headphones.

Playback buttons and function
buttons
Unit: BLUETOOTH  (play/
pause) button (page 16, 17)
Press to select the Bluetooth function.
Press to start or pause playback of the
music on the Bluetooth device (Bluetooth
mobile phone, etc.).
Press to select the CD function.
Press to start or pause playback of a disc.
Unit: iPod  (play/pause)
button (page 21, 22)
Press to select the iPod function.
Press to start or pause playback of the
iPod.
Remote:  (play) button,
 (pause) button
Press to start or pause playback.
TUNER/BAND button (page 14)
Press to select the TUNER function.
Press to select FM or AM reception
mode.
Unit: FUNCTION button (page 13,
14, 19, 20, 21, 23)
Remote: FUNCTION +/ button
(page 13, 14, 19, 20, 21, 23)

PLAY MODE/TUNING MODE
button (page 13, 14, 25, 26)
Press to select the play mode of a CD or
MP3 disc.
Press to select the tuning mode.

Unit: ENTER button (page 22, 25)
Remote: (enter) button (page
12, 16, 22, 25, 26, 27)
Press to enter the settings.

/ (go back/go forward)
button (page 13, 16, 17, 21, 22,
25)
Press to select a track or file.
Unit: TUNE +/ (tuning) button
(page 14)
Remote: +/ (tuning) button
(page 14, 26)
Press to select the function.
Press to tune in the desired station.

iPod connector
+/ (select folder) button
(page 13, 16, 17, 25)

/ (rewind/fast forward)
button (page 13, 16, 17, 22)
Place an iPod on the connector to listen
to audio contents stored in the iPod.
REPEAT/FM MODE button (page
13, 14)
Guide to parts and controls
Unit: CD  (play/pause)
button (page 13)
Press to select a folder.
Press to find a point in a track or file.
Press to listen to a disc, a single track or
file repeatedly.
Press to select the FM reception mode
(monaural or stereo).
Continued

GB


Unit: VOL +/ button (page 13,
14, 17, 20, 21, 23)
Remote: VOLUME +/ button
(page 13, 14, 17, 20, 21, 23)
TIMER MENU button (page 12,
27)
Press to adjust the volume.

DISPLAY button (page 17, 22, 24)
Press to change the information on the
display.

Sound buttons (page 23)
Unit: DSGX button
Remote: EQ button
Press to select the sound effect.

Unit: /CANCEL (stop/cancel)
button (page 13, 14, 16, 17, 19)
Remote:  (stop) button (page
13, 14, 16, 17, 19)
Press to stop playback.

CLEAR button (page 17, 19, 25)
Press to delete a pre-programmed track
or file.
Press to erase the pairing registration
information of the Bluetooth device.
GB
Press to set the clock and the Play Timer.

TOOL MENU button (page 22)
Press to select a menu when using the
iPod.

Battery compartment lid
(page 11)

 RETURN button (page 22)
Press to return to the previous menu
when using the iPod.

/// button (page 12, 22, 27)
Press to select the menu items.

TUNER MEMORY button (page
26)
Press to preset the radio station.

SLEEP button (page 27)
Press to set the Sleep Timer.


Function
DSGX (page 23)


Audio format
Timer (page 27)


Play mode (page 13)
Play/Pause


Tuner reception mode (page 14)
Tuner reception (page 14)
Text information
Guide to parts and controls
Information on the display
GB
Getting Started
Hooking up the system securely
Right speaker
or
Left speaker
Wall socket
 Speaker cord (Red/)
 Speaker cord (Black/)
 AM loop antenna
 FM lead antenna (Extend it horizontally.)
 White side for North American model
 Brown side for other regions
10GB
Notes
Find a location and an orientation that
provide good reception, and then set up
the antenna.
Keep the antennas away from the speaker
cords and the power cord to avoid
picking up noise.
With normal use, the batteries should last for
about six months.
Do not mix an old battery with a new one or
mix different types of batteries.
If you do not use the remote for a long period
of time, remove the batteries to avoid damage
from battery leakage and corrosion.
 Speakers
To use the iPod
Insert only the stripped portion of the
speaker cords into the SPEAKER jacks.
 Power
Connect the power cord to a wall socket.
If the plug does not fit the wall socket,
detach the supplied plug adaptor (only
for models equipped with an adaptor).
Insert an iPod Dock Adapter into the
unit’s connector  before use.
For details on the supplied iPod Dock
Adapters, refer to the instructions
supplied with the Dock Adapters.
Getting Started
 Antennas
When carrying this system
1 Remove a disc to protect the CD
mechanism.
2 Press FUNCTION +/ (or FUNCTION
on the unit)  repeatedly to select
the CD function.
3 Hold down VOL +  and DSGX 
on the unit, and press   on the
unit until “STANDBY” appears.
To remove the iPod Dock Adapter, pull
it up with your fingernail or a flat object
using the slot inside the adapter.
Slot
4 After “LOCK” appears, unplug the
power cord.
To use the remote
Slide and remove the battery
compartment lid , and insert the two
supplied R6 (size AA) batteries,  side
first, matching the polarities shown
below.
11GB
Setting the clock
Use buttons on the remote to set the
clock.
1 Press /  to turn on the
system.
2 Press TIMER MENU .
The hour indication flashes in the
display.
If “PLAY SET?” flashes in the display,
press /  repeatedly to select
“CLOCK SET?” and then press .
3 Press /  repeatedly to set
the hour, and then press
.
4 Use the same procedure to set
the minutes.
The clock settings are lost when you
disconnect the power cord or if a
power failure occurs.
To display the clock when the system
is off
Press DISPLAY . The clock is displayed
for about 8 seconds.
12GB
Basic Operations
Playing a CD/MP3 disc
1 Select the CD function.
2 Place a disc.
Press   on the unit, and place
a disc with the label side up on the
disc tray.
To close the disc tray, press   on
the unit again.
Do not force the disc tray closed with
your finger, as this may damage the
unit.
3 Start playback.
Press  (or CD  on the unit)
.
4 Adjust the volume.
Press VOLUME +/ (or VOL +/ on
the unit) .
To
Press
Pause playback  (or CD  on the
unit) . To resume
play, press the button
again.
Stop playback  .
Select a folder
+/ .
on an MP3
disc
Select a track / .
or file
Find a point in Hold down /
a track or file  during playback, and
release the button at the
desired point.
Select Repeat REPEAT  repeatedly
Play
until “REP” or “REP1”
appears.
Basic Operations
Press FUNCTION +/ (or
FUNCTION on the unit) 
repeatedly.
Other operations
To change the play mode
Press PLAY MODE  repeatedly while
the player is stopped. You can select
normal play (“ *” for all MP3 files
in the folder on the disc), shuffle play
(“SHUF” or “
SHUF*”), or program
play (“PGM”).
* When playing a CD-DA disc,
(SHUF)
Play performs the same operation as normal
(shuffle) play.
Notes on Repeat Play
All tracks or files on a disc are played
repeatedly up to five times.
“REP1” indicates that a single track or file is
repeated until you stop it.
Continued

13GB
Notes on playing MP3 discs
Do not save other types of files or
unnecessary folders on a disc that has MP3
files.
Folders that have no MP3 files are skipped.
MP3 files are played back in the order that
they are recorded onto the disc.
The system can only play MP3 files that have
a file extension of “.MP3”.
If there are files on the disc that have the
“.MP3” file extension, but that are not MP3
files, the unit may produce noise or may
malfunction.
The maximum number of:
 folders is 255 (including the root folder).
 MP3 files is 511.
 MP3 files and folders that can be
contained on a single disc is 512.
 folder levels (the tree structure of files) is
8.
Compatibility with all MP3 encoding/writing
software, recording device, and recording
media cannot be guaranteed. Incompatible
MP3 discs may produce noise or interrupted
audio or may not play at all.
Notes on playing multisession discs
If the disc begins with a CD-DA (or MP3)
session, it is recognized as a CD-DA (or
MP3) disc, and other sessions are not played
back.
A disc with a mixed CD format is recognized
as a CD-DA (audio) disc.
Listening to the radio
1 Select “TUNER FM” or “TUNER
AM.”
Press FUNCTION +/ (or TUNER/
BAND on the unit)  repeatedly.
2 Select the tuning mode.
Press TUNING MODE  repeatedly
until “AUTO” appears.
3 Tune in the desired station.
Press +/ (or TUNE +/ on
the unit) . Scanning stops
automatically when a station is
tuned in, and then “TUNED” and
“STEREO” (for stereo programs only)
appear.
4 Adjust the volume.
Press VOLUME +/ (or VOL +/
on the unit) .
To stop automatic scanning
Press  .
To tune in a station with a weak signal
If “TUNED” does not appear and the
scanning does not stop, press TUNING
MODE  repeatedly until “AUTO” and
“PRESET” disappear, and then press
+/ (or TUNE +/ on the unit) 
repeatedly to tune in the desired station.
To reduce static noise on a weak FM
stereo station
Press FM MODE  repeatedly until
“MONO” appears to turn off stereo
reception.
14GB
Using the Bluetooth
function
You can listen to music from your
Bluetooth mobile phone or Bluetooth
device over a wireless connection.
Basic Operations
This system supports Bluetooth A2DP
and AVRCP profiles. For details on
Bluetooth wireless technology, see
“Bluetooth wireless technology” (page
38).
Check the websites below for the latest
information about compatible devices.
For customers in the U.S.A.:
<http://www.sony.com/shelfsupport>
For customers in Canada:
English <http://www.sony.ca/
ElectronicsSupport/>
French <http://fr.sony.ca/
ElectronicsSupport/>
For customers in Europe:
<http://support.sony-europe.com/>
For customers in Latin America:
<http://www.sony-latin.com/index.crp>
For customers in Asia and Oceania:
<http://www.sony-asia.com/support>
Listening to music of a
Bluetooth mobile phone or
Bluetooth device
Follow the procedure below to listen to
music from Bluetooth devices with this
system.
Pairing this system with a Bluetooth
device

Connecting to registered devices

Playing music of a Bluetooth device
For details about the operations of
the Bluetooth device, also refer to the
operation manual supplied with your
Bluetooth device.
Continued

15GB
Pairing this system with a Bluetooth
device
Pairing is an operation where Bluetooth
devices register with each other
beforehand. Use the procedure below
to pair the system with your Bluetooth
device. Once a pairing operation is
performed, it does not need to be
performed again. If pairing is already
completed, proceed to “Playing music of
a Bluetooth device” (page 17).
1 Place the Bluetooth device to be
connected to this system within
1 meter of the system.
2 Select the Bluetooth function.
Press BLUETOOTH   on
the unit.
3 Operate the Bluetooth device
and perform the pairing
operation.
For details about the operations of
the Bluetooth device, refer to the
operation manual supplied with your
Bluetooth device.
When searching for this system with
the Bluetooth device, a list of the
devices found may appear in the
Bluetooth device display depending
on the type of Bluetooth device.
This system appears as “CMTBX50BTi.”
When establishing a connection with
this system, select the audio profile
(A2DP, AVRCP) at the Bluetooth
device. If the Bluetooth device does
not support the AVRCP profile, you
cannot perform playback or other
operations with the system (page 17).
16GB
4 Enter the passkey.
Passkey entry may be required
depending on the type of Bluetooth
device.
When “PIN?” and a countdown
appear, enter the passkey at the
system as follows:
Press / and /
on the remote (or
+/ and
/  on the unit) 
to enter the same passkey that was
entered at the Bluetooth device, and
then press .
Once pairing is completed and the
connection is established, the system
display changes as follows:
“Connect”  Name of the Bluetooth
device
To cancel passkey entry partway
Press  .
If passkey entry still required, turn off the
Bluetooth device.
Notes
“Passkey” may be called “Passcode,” “PIN
code,” “PIN number” or “Password,” etc.
depending on the device.
This system only supports numerical
passkeys up to 4 digits.
The pairing standby status of the system is
cancelled after about 30 seconds.
If pairing is not successful, redo the
procedure from step 1.
While connected to a Bluetooth device, this
system cannot be detected and a connection
cannot be established from another
Bluetooth device.
To erase all the pairing registration
information
1 Press BLUETOOTH   on the
2 Press CLEAR .
“Delete?” appears.
3 Press
.
“Complete!” appears and all the
pairing information is erased.
Note
In order to connect with a Bluetooth device
after performing this operation, you must enter
the passkey again.
Playing music of a Bluetooth device
You can operate a Bluetooth device by
connecting the system and a Bluetooth
device using AVRCP.
1 Select the Bluetooth function.
Press BLUETOOTH   on
the unit.
2 Establish a connection from the
Bluetooth device.
For details about the operations of
the Bluetooth device, refer to the
operation manual supplied with your
Bluetooth device.
Once the connection is established,
the system display changes as follows:
“Connect”  Name of the Bluetooth
device
Press  (or BLUETOOTH  on
the unit) .
Depending on the Bluetooth device,
you may need to start up the AV
software of the Bluetooth device
beforehand.
4 Adjust the volume.
Press VOLUME +/ (or VOL +/ on
the unit) .
To check the address of a connected
Bluetooth device
Press DISPLAY  while the Bluetooth
device name appears in the system
display.
The Bluetooth device address appears for
8 seconds.
Basic Operations
unit.
When the system is connected with a
Bluetooth device (when the Bluetooth
device name or other information
appears in the system display), press
and hold BLUETOOTH  on the
unit for about 2 seconds to put the
system in Bluetooth standby mode.
3 Start playback.
To cancel the connection with a
Bluetooth device
Press and hold BLUETOOTH 
on the unit for about 2 seconds until
“Disconnect” appears, or until the
information on the display (device name,
etc.) disappears.
Other operations
To
Press
Pause playback  (or BLUETOOTH
 on the unit) .
Stop playback  .
Select a folder
+/ .
Select a file
/ .
Find a point in Hold down /
.
a file
Note
These operations may not be available for
certain Bluetooth devices. In addition, the
actual operations may differ depending on the
connected Bluetooth device.
Continued

17GB
Notes on connections with Bluetooth
devices
If you cannot connect with a paired
Bluetooth device, perform the pairing
operation between the system and the
Bluetooth device again.
Depending on the type of Bluetooth device,
you can adjust the volume using the controls
of the Bluetooth device.
When BLUETOOTH   on the unit
is pressed while connected to Bluetooth
headphones, it may take some time until
a connection is made to the system from
another Bluetooth device.
Use the A2DP-capable or A2DP- and
AVRCP-capable Bluetooth device with the
system in a peer-to-peer environment.
Listening to music on this
system using Bluetooth
headphones
You can listen to music played on this
system using your Bluetooth headphones
over a wireless connection.
Tip
Bluetooth devices that have been connected
with this system in the past are registered with
this system.
When a Bluetooth connection is not
currently established, you can easily
connect the system to a Bluetooth device
by pressing BLUETOOTH   on the
unit. (Connection is attempted with up to
3 devices in order from the most recently
connected device, and the attempts end when
a connection is established.) This function may
not be available depending on the Bluetooth
device you are using.
If a connection cannot be made, the system
returns to the standby mode.
18GB
Follow the procedure below to listen
to music on this system with Bluetooth
headphones.
Pairing this system with Bluetooth
headphones

Connecting to registered headphones

Playing music on this system
For details about the operations of the
Bluetooth headphones, also refer to the
operation manual supplied with your
Bluetooth headphones.
Pairing this system with Bluetooth
headphones
1 Select a function other than the
Bluetooth function.
Press FUNCTION +/ (or
FUNCTION on the unit) 
repeatedly.
2 Place the Bluetooth
headphones to be connected
to this system within 1 meter of
the system.
3 Put the Bluetooth headphones
in pairing mode.
For details about the operations of the
Bluetooth headphones, refer to the
operation manual supplied with your
Bluetooth headphones.
4 Press and hold BLUETOOTH 
on the unit for about 7 seconds
until the BLUETOOTH indicator
 flashes.
Sound output from the speakers is
stopped.
5 Enter the passkey.
Follow the same procedure as in
step 4 of “Pairing this system with a
Bluetooth device” (page 16).
Once pairing is completed and the
connection is established, the system
display changes as follows:
“Connect”  Name of the Bluetooth
device
Press  .
Notes
“Passkey” may be called “Passcode,” “PIN
code,” “PIN number” or “Password,” etc.
depending on the device.
This system only supports numerical
passkeys up to 4 digits.
The pairing standby status of the system is
cancelled after about 30 seconds.
If pairing is not successful, redo the
procedure from step 1.
While connected to a Bluetooth device, this
system cannot be detected and a connection
cannot be established from another
Bluetooth device.
Pairing may not be possible if other
Bluetooth devices are present around the
system. In this case, turn off the other
Bluetooth devices.
Basic Operations
Pairing is an operation where Bluetooth
devices register with each other
beforehand. Use the procedure below
to pair the system with your Bluetooth
headphones. Once a pairing operation
is performed, it does not need to be
performed again. If pairing is already
completed, proceed to “Playing music on
this system” (page 20).
To cancel passkey entry partway
To erase all the pairing registration
information
1 Press BLUETOOTH   on the
unit.
When the system is connected with a
Bluetooth device (when the Bluetooth
device name or other information
appears in the system display), press
and hold BLUETOOTH  on the
unit for about 2 seconds to put the
system in Bluetooth standby mode.
2 Press CLEAR .
“Delete?” appears.
3 Press
.
“Complete!” appears and all the
pairing information is erased.
Note
To connect with Bluetooth headphones after
performing this operation, you must enter the
passkey again.
Continued

19GB
Playing music on this system
You can operate this system from
Bluetooth headphones by connecting the
system and Bluetooth headphones using
AVRCP.
1 Select a function other than the
Bluetooth function.
Press FUNCTION +/ (or
FUNCTION on the unit) 
repeatedly.
2 Establish a connection with the
Bluetooth headphones.
Press and hold BLUETOOTH  on
the unit for about 2 seconds until the
BLUETOOTH indicator  lights up,
then release the button.
Sound output from the speakers is
stopped.
If more than one Bluetooth device
that has been connected in the past
is present around the system, the
system attempts to connect with up
to 3 most recently connected devices.
(Connection is attempted with up
to 3 devices in order from the most
recently connected device, and the
attempts end when a connection is
established.)
Once the connection is established,
the system display changes as follows:
“Connect”  Name of the Bluetooth
device
3 Start playback of the music for
the function selected in step 1.
Depending on the type of Bluetooth
headphones, you can operate this
system (playback, volume control,
etc.) using the headphone’s controls.
For details about the operations of the
Bluetooth headphones, refer to the
operation manual supplied with your
Bluetooth headphones.
20GB
4 Adjust the volume.
Press VOLUME +/ (or VOL +/ on
the unit) .
To cancel the connection with
Bluetooth headphones
Press and hold BLUETOOTH  on
the unit for about 2 seconds until the
BLUETOOTH indicator  turns off.
Sound is output from the speakers.
Notes
If you cannot connect with paired Bluetooth
headphones, perform the pairing operation
between the system and the Bluetooth
headphones again.
When the system is changed to a function
other than the Bluetooth function and
BLUETOOTH  on the unit is pressed
while connected to a Bluetooth device, it may
take some time until a connection is made
with the Bluetooth headphones.
This system stores separate volume settings
for when listening through the speakers
or PHONES jack  on the unit, or when
listening through Bluetooth headphones.
Use the A2DP-capable or A2DP- and
AVRCP-capable Bluetooth device with the
system in a peer-to-peer environment.
Playing the iPod
You can listen to audio contents stored in
the iPod.
1 Select the iPod function.
2 Place the iPod.
3 Start playback.
Press  (or iPod  on the unit)
.
When placing or removing the iPod, handle
the iPod in the same angle as that of the iPod
connector  on the unit and do not twist or
sway the iPod to prevent connector damage.
Do not carry the unit with an iPod set
on the connector. Doing so may cause a
malfunction.
When placing or removing the iPod, brace
the unit with one hand and take care not to
press the controls of the iPod by mistake.
Before disconnecting the iPod, pause
playback.
While playing video, you cannot use
/ . You can fast rewind (fast
forward) by holding down / .
To change the volume level, use VOLUME
+/ (or VOL +/ on the unit) . The
volume level does not change even if adjusted
on the iPod.
This system is designed for iPod only. You
cannot connect any other portable audio
players.
To use an iPod, refer to the user’s guide of
your iPod.
Sony cannot accept responsibility in the
event that data recorded to iPod is lost or
damaged when using an iPod with this unit.
Basic Operations
Press FUNCTION +/ (or
FUNCTION on the unit) 
repeatedly.
Notes
4 Adjust the volume.
Press VOLUME +/ (or VOL +/ on
the unit) .
Continued

21GB
Other operations
You can control your iPod with the
following buttons on the remote or unit.
To
Press
Pause playback  (pause) (or iPod
 (play/pause) on
the unit)  or  (stop)
.
Scroll up/
/ . You can scroll
down the iPod up or down the iPod
menus
menus much like the
Click Wheel operations
of the iPod or the drag
up-or-down operations
of the iPod touch.
Select a track / (go back/go
or chapter of forward) . To fastaudiobook/
forward or fast-rewind,
podcast
hold down the button.
Choose the
 / (or ENTER on
selected item the unit) . You can
choose the selected item
much like the center
button on the iPod or
the touch operation of
the iPod touch.
Find a point
/ (fast rewind/
in a track or
fast forward)  during
chapter of
playback, and release
audiobook/
the button at the desired
podcast
point.
Return to the  /TOOL MENU
previous menu /  (return) .
or select a
You can return to the
menu
previous menu or select
a menu much like
the Menu button on
the iPod or the touch
operation of the iPod
touch.
22GB
To use the system as a battery charger
You can use the system as a battery
charger for the iPod when the system is
both on and off.
The charging begins when the iPod is
placed on the unit’s connector .
The charging status appears in the iPod
display. For details, see the user’s guide of
your iPod.
To stop charging the iPod
Remove the iPod. If you stop charging
the iPod when the system is off, press
DISPLAY  until the clock disappears
in the display.
Using optional audio
components
1 Connect additional audio
2 Turn down the volume.
Press VOLUME  (or VOL  on the
unit) .
3 Select the AUDIO IN function.
Press FUNCTION +/ (or
FUNCTION on the unit) 
repeatedly.
To add a sound effect
To
Generate a
more dynamic
sound
(Dynamic
Sound
Generator
X-tra)
Set the sound
effect
Press
DSGX  on the unit.
EQ  repeatedly
to select “BASS”
or “TREBLE,” and
then press +/ 
repeatedly to adjust the
level.
Basic Operations
component to the AUDIO
IN jack  on the unit using
an audio analog cord (not
supplied).
Adjusting the sound
4 Start playing the connected
component.
5 Adjust the volume.
Press VOLUME +/ (or VOL +/ on
the unit) .
23GB
Changing the display
To
Change
information on
the display1)2)
Check the
clock when the
system is off3)
Press
DISPLAY  repeatedly
when the system is on.
DISPLAY  when
the system is off4). The
clock is displayed for 8
seconds.
For example, you can view CD/MP3 disc
information, such as;
track or file number during normal play.
track or file name (“ ”) during normal play.
artist name (“ ”) during normal play.
album or folder name (“
”) during normal
play.
total playing time while the player is
stopped.
2)
When the system and a Bluetooth device are
connected using the Bluetooth function, you
can view the Bluetooth device address.
If the connected Bluetooth device supports
metadata transfer, you can also view the
Bluetooth device information, such as the
elapsed playing time, track title, artist name
or album name during playback.
3)
The clock is displayed continuously while the
iPod is being charged. To turn off the clock
display, press DISPLAY  (See “To stop
charging the iPod” (page 22)).
4)
The STANDBY indicator  on the unit
lights up when the system is off.
1)
24GB
Notes on the display information
Characters that cannot be displayed appear
as “_”.
The following are not displayed:
 total playing time for a CD-DA disc
depending on the play mode.
 total playing time and remaining playing
time for an MP3 disc.
The following is not displayed correctly:
 folder and file names that do not follow
either the ISO9660 Level 1, Level 2 or
Joliet in the expansion format.
The following is displayed:
 ID3 tag information for MP3 files when
ID3 version 1 and version 2 tags are used
(up to 62 characters for an MP3 disc).
The display information may not be updated
or displayed properly depending on the
Bluetooth device you are using.
The display information may differ
depending on the connected Bluetooth
device.
The display information for the Bluetooth
device may not be updated properly
depending on the communication
environment or surrounding conditions.
Other Operations
Creating your own
program
(Program Play)
1 Select the desired function.
2 Press PLAY MODE  repeatedly
until “PGM” appears while the
system is stopped.
3 Press /  repeatedly
until the desired track or file
number appears.
When programming files, press
+/  repeatedly to select the
desired folder, and then select the
desired file.
Example: When programming tracks
on a CD
(or ENTER on the unit)
 to add the track or file to the
program.
“ . ” appears when the total
program time exceeds 100 minutes
for a CD, or when you select a CD
track whose number is 21 or over, or
when you select an MP3 file.
5 Repeat steps 3 through 4 to
program additional tracks or
files, up to a total of 25 tracks or
files.
6 To play your program of tracks
or files, press  .
The program remains available until
you open the disc tray. To play the
same program again, press  .
Other Operations
Press FUNCTION +/ (or
FUNCTION on the unit) 
repeatedly to select the CD function.
4 Press
To cancel Program Play
Press PLAY MODE  repeatedly until
“PGM” disappears while the system is
stopped.
To delete the last track or file of the
program
Press CLEAR  while the system is
stopped.
Selected track or file number
Total playing time of
program (including
selected track or file)
25GB
Presetting radio
stations
You can preset your favorite radio
stations and tune them in instantly
by selecting the corresponding preset
number.
Use buttons on the remote to preset
stations.
1 Tune in the desired station (see
“Listening to the radio” (page
14)).
2 Press TUNER MEMORY .
Preset number
3 Press +/  repeatedly to
select your desired preset
number.
If another station is already assigned
to the selected preset number,
the station is replaced by the new
stations.
4 Press .
5 Repeat steps 1 through 4 to
store other stations.
You can preset up to 20 FM and 10
AM stations.
The preset stations are retained
for about half a day even if you
disconnect the power cord or if a
power failure occurs.
26GB
6 To call up a preset radio
station, press TUNING MODE
 repeatedly until “PRESET”
appears, and then press +/ 
repeatedly to select the desired
preset number.
Using the Timers
The system offers two timer functions.
If you use the Play Timer with the Sleep
Timer, the Sleep Timer has priority.
Press SLEEP  repeatedly.
If you select “AUTO,” the system
automatically turns off after the current
disc stops or in 100 minutes.
Play Timer:
You can wake up to CD, tuner or iPod at
a preset time.
Use buttons on the remote to control the
Play Timer. Make sure you have set the
clock.
1 Prepare the sound source.
Prepare the sound source, and then
press VOLUME +/  to adjust the
volume.
To start from a specific track or file,
create your own program (page 25).
2 Press TIMER MENU .
3 Press /  repeatedly to
Press /  repeatedly to set the
hour, and then press . The
minute indication flashes. Use the
procedure above to set the minutes.
5 Use the same procedure as in
step 4 to set the time to stop
playing.
6 Select the sound source.
Press /  repeatedly until the
desired sound source appears, and
then press . The display shows
the timer settings.
7 Press /  to turn off the
system.
The system turns on 15 seconds
before the preset time. If the system is
on at the preset time, the Play Timer
will not play.
Other Operations
Sleep Timer:
You can fall asleep to music. This
function works even if the clock is not
set.
4 Set the time to start playing.
Note
Before the system is turned off, if a connection
is made with the Bluetooth headphones,
sounds played by the Play Timer may be output
to the Bluetooth headphones.
Note on the iPod touch user
The Play Timer may not be activated
depending on the status of the connected iPod
touch.
select “PLAY SET?,” and then
press .
“ON TIME” appears, and the hour
indication flashes.
Continued

27GB
To activate or check the timer again
1 Press TIMER MENU .
“TIMER SEL?” flashes in the display.
2 Press
.
3 Press /  repeatedly to select
“PLAY SEL?.”
4 Press
.
To cancel the timer
1 Press TIMER MENU .
“TIMER SEL?” flashes in the display.
2 Press
.
3 Press /  repeatedly to select
“TIMER OFF?.”
4 Press
.
To change the setting
Start over from step 1.
Tip
The Play Timer setting remains as long as the
setting is not canceled manually.
28GB
Others
Troubleshooting
1 Make sure the power cord and
speaker cords are correctly and firmly
connected.
2 Find your problem in the checklist
If the STANDBY indicator flashes
Immediately unplug the power cord,
and check the following items.
If your system has a voltage
selector, is the voltage selector set to
the correct voltage?
Are you using only the supplied
speakers?
Is anything blocking the ventilation
holes on the top or back of the
system?
Is the iPod connector  shortcircuited?
After the STANDBY indicator 
stops flashing, reconnect the power
cord, and turn on the system. If the
issue persists, contact your nearest
Sony dealer.
There is no sound.
If the BLUETOOTH indicator  is lit
or flashing when a function other than
the Bluetooth function is selected, no
sound is heard through the speakers
or PHONES jack . Press and hold
BLUETOOTH  for about 2 seconds
until the BLUETOOTH indicator 
turns off.
Others
below, and take the indicated
corrective action.
If the issue persists, contact your
nearest Sony dealer.
Severe hum or noise.
Move the system away from sources of
noise.
Connect the system to a different wall
socket.
Install a noise filter (available
separately) to the power cord.
The remote does not function.
Remove any obstacles between the
remote and the remote sensor  on
the unit, and position the unit away
from fluorescent lights.
Point the remote at the system’s sensor.
Move the remote closer to the system.
The STANDBY indicator  remains lit
after unplugging the power cord.
The STANDBY indicator  may not
turn off immediately after unplugging
the power cord. This is not a
malfunction. The indicator will turn off
after about 40 seconds.
General
Sound comes from one channel,
or the left and right volumes are
unbalanced.
Place the speakers as symmetrically as
possible.
Connect only the supplied speakers.
Continued

29GB
CD/MP3 player
Bluetooth device
The sound skips, or the disc will not
play.
Wipe the disc clean, and replace it.
Move the system to a location away
from vibration (for example, on top of
a stable stand).
Move the speakers away from the
system, or place them on separate
stands. At high volume, speaker
vibration may cause the sound to skip.
Pairing cannot be done.
Move the Bluetooth device closer to
the system.
Pairing may not be possible if other
Bluetooth devices are present around
the system. In this case, turn off the
other Bluetooth devices.
Enter the same passkey that was
entered at the Bluetooth device
correctly.
Play does not start from the first
track.
Press PLAY MODE  repeatedly until
both “PGM” and “SHUF” disappear to
return to normal play.
Connection is not possible.
The Bluetooth device you attempted
to connect does not support the A2DP
profile, and cannot be connected with
the system.
Enable the Bluetooth function of the
Bluetooth device.
Establish a connection from the
Bluetooth device.
The pairing registration information
has been erased. Perform the pairing
operation again.
While connected to a Bluetooth device,
this system cannot be detected and a
connection cannot be established from
another Bluetooth device.
Erase the pairing registration
information of a Bluetooth device and
perform the pairing operation again.
Starting playback takes more time
than usual.
The following discs take a longer time
to start playback.
a disc recorded with a complicated
tree structure.
a disc recorded in multisession
mode.
a disc that has not been finalized (a
disc to which data can be added).
a disc that has many folders.
30GB
The sound skips or fluctuates, or the
connection is lost.
The system and the Bluetooth device
are too far apart.
If there are obstacles between the
system and your Bluetooth device,
remove or avoid the obstacles.
If there is equipment that generates
electromagnetic radiation, such as a
wireless LAN, other Bluetooth device,
or a microwave oven nearby, move
them away.
Severe hum or noise
If there are obstacles between the
system and your Bluetooth device,
remove or avoid the obstacles.
If there is equipment that generates
electromagnetic radiation, such as a
wireless LAN, other Bluetooth device,
or a microwave oven nearby, move
them away.
Turn down the volume of the
connected Bluetooth device.
iPod
There is no sound.
Make sure the iPod is connected
securely.
Make sure the iPod is playing music.
Adjust the volume.
Others
The sound of your Bluetooth device
cannot be heard on this system.
Turn up the volume on your Bluetooth
device first, and then adjust the volume
using VOLUME +/ (or VOL +/ on
the unit) .
The sound from the Bluetooth
headphones is distorted.
Turn down the volume of the system
using VOLUME  (or VOL  on the
unit) . If your headphones have a
volume control, also adjust the volume
using the headphone’s volume control.
Press DSGX  on the unit repeatedly
until “DSGX OFF” appears.
Press EQ  repeatedly to select
“BASS” or “TREBLE,” and then press
  repeatedly to turn down the
level.
The sound is distorted.
Turn down the volume.
Set the “EQ” setting of the iPod to
“Off ” or “Flat.”
The iPod cannot be charged.
Make sure the iPod is connected
securely.
Continued

31GB
Tuner
Severe hum or noise, or stations
cannot be received. (“TUNED” or
“STEREO” flashes on the display.)
Connect the antenna properly.
Find a location and an orientation that
provide good reception, and then set
up the antenna again.
Keep the antennas away from the
speaker cords and the power cord to
avoid picking up noise.
Connect a commercially available
external antenna.
Consult your nearest Sony dealer if the
supplied AM antenna has come off the
plastic stand.
Turn off nearby electrical equipment.
To change the AM tuning interval
Turn off CD player power by using the
CD power management function. By
default, CD power is turned on.
1 Press FUNCTION +/ (or FUNCTION
on the unit)  repeatedly to select
the CD function, and then turn off
the system.
2 After “STANDBY” stops flashing, press
/  on the unit while holding
down   on the unit.
“CD POWER OFF” appears. With CD
player power turned off, disc access
time is increased. To turn on CD
player power, repeat the procedure
until “CD POWER ON” appears.
To reset the system to factory settings
The AM tuning interval is factory-preset
to 9 kHz (or 10 kHz, for some areas).
Use buttons on the unit to change the
AM tuning interval.
If the system still does not operate
properly, reset the system to factory
settings.
Use buttons on the unit to reset the
system to its factory default settings.
1 Tune in any AM station, and then
1 Disconnect and reconnect the power
turn off the system.
2
While holding down ENTER , press
/ .
All the AM preset stations are erased.
To reset the interval to the factory
preset, repeat the procedure.
32GB
To improve tuner reception
cord, and then turn on the system.
2 Press  , VOL +  and /  at
the same time.
All user-configured settings, such as
preset radio stations, timer, and the
clock, are deleted.
Messages
CD/MP3 player, Tuner
Connect: Bluetooth communication was
established.
Connecting: The system is attempting
to connect with recently connected
Bluetooth devices.
Disconnect: Communication with a
Bluetooth device was cut off for some
reason, or Bluetooth communication
was ended.
No Device: A pairable Bluetooth device
was not found, or connection was not
possible.
Not in Use: The system is not connected
with a Bluetooth device using A2DP, or
the Bluetooth device does not support
a command for selecting a folder
operations (
+/ ).
PIN?: The system is asking for the
passkey. For details, see “Using the
Bluetooth function” (page 15).
Please Wait: The system is readying for
usage of a Bluetooth device.
Others
CD Over: You have reached the end of
the disc while pressing   during
playback or pause.
Complete!: The preset operation ended
normally.
LOCKED: The disc tray does not open.
Contact your nearest Sony dealer.
No Disc: There is no disc in the system,
or you have loaded a disc that cannot
be played.
No Step: All of the programmed tracks
or files have been erased.
Push STOP!: You pressed PLAY MODE
 during playback.
Reading: The system is reading
information of the disc. Some buttons
are not available.
Step Full!: You tried to program more
than 26 tracks or files (steps).
TIME NG!: The Play Timer start and end
times are set to the same time.
Bluetooth device
33GB
Precautions
Discs that this system CAN play
Audio CD
CD-R/CD-RW (audio data/MP3 files)
Discs that this system CANNOT play
CD-ROM
CD-R/CD-RW other than those
recorded in music CD format or MP3
format conforming to ISO9660 Level
1/Level 2, Joliet or multisession
CD-R/CD-RW recorded in
multisession that have not ended by
“closing the session”
CD-R/CD-RW of poor recording
quality, CD-R/CD-RW that have
scratches or are dirty, or CD-R/CDRW recorded with an incompatible
recording device
CD-R/CD-RW which is finalized
incorrectly
Discs containing files other than
MPEG 1 Audio Layer-3 (MP3) files
Discs of non-standard shape (for
example, heart, square, star)
Discs that have adhesive tape, paper, or
sticker attached to them
Rental or used discs with attached seals
where the glue extends beyond the seal
Discs that have labels printed using ink
that feels tacky when touched
34GB
Notes on discs
Before playing, wipe the disc with a
cleaning cloth from the center out to
the edge.
Do not clean discs with solvents, such
as benzine thinner, or commercially
available cleaners or anti-static spray
intended for vinyl LPs.
Do not expose discs to direct sunlight
or heat sources such as hot air ducts,
nor leave it in a car parked in direct
sunlight.
On safety
Completely disconnect the power
cord (mains lead) from the wall socket
(mains) if it is not going to be used
for an extended period of time. When
unplugging the unit, always grip the
plug. Never pull the cord itself.
Should any solid object or liquid get
into the system, unplug the system, and
have it checked by qualified personnel
before operating it again.
The AC power cord can be changed
only by a qualified service facility.
On the speaker system
This speaker system is not magnetically
shielded, and the picture on nearby TV
sets may become magnetically distorted.
In this situation, turn off the TV, wait
15 to 30 minutes, and turn it back on.
If there is no improvement, move the
speakers far away from the TV.
Cleaning the cabinet
Clean this system with a soft cloth
slightly moistened with a mild detergent
solution. Do not use any type of abrasive
pad, scouring powder, or solvent, such as
thinner, benzine, or alcohol.
Others
On placement
Do not place the system in an inclined
position or in locations that are
extremely hot, cold, dusty, dirty, or
humid or lacking adequate ventilation,
or subject to vibration, direct sunlight
or a bright light.
Be careful when placing the unit
or speakers on surfaces that have
been specially treated (for example,
with wax, oil, polish) as staining or
discoloration of the surface may result.
If the system is brought directly
from a cold to a warm location or is
placed in a very damp room, moisture
may condense on the lens inside the
CD player, and cause the system to
malfunction. In this situation, remove
the disc, and leave the system turned
on for about an hour until the moisture
evaporates.
On heat buildup
Heat buildup on the unit during
operation is normal and is not cause
for alarm.
Do not touch the cabinet if it has been
used continuously at a high volume
because the cabinet may have become
hot.
Do not obstruct the ventilation holes.
35GB
Specifications
Supported codecs:
Receive: SBC (Sub Band Codec), MP3
Transmit: SBC (Sub Band Codec)
The actual range will vary depending on
factors such as obstacles between devices,
magnetic fields around a microwave oven,
static electricity, reception sensitivity,
antenna’s performance, operating system,
software application, etc.
2)
Bluetooth standard profiles indicate the
purpose of Bluetooth communication
between devices.
1)
Main unit (HCD-BX50BTi/Compact Disc
Receiver)
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(The United States model only)
With 6 ohm loads, both channels driven,
from 120  10,000 Hz; rated 25 watts per
channel minimum RMS power, with no
more than 10% total harmonic distortion
from 250 milliwatts to rated output.
Amplifier section
Continuous RMS power output
(reference): 25 + 25 watts (6 ohms at
1 kHz, 10% THD)
Inputs:
AUDIO IN (stereo mini jack):
voltage 250 mV, impedance
47 kilohms
Outputs:
PHONES (stereo mini jack): accepts
headphones of 8 ohms or more
SPEAKER: accepts impedance of
6 ohms
Bluetooth section
Communication system:
Bluetooth Standard version 2.0
Output:
Bluetooth Standard Power Class 2
Maximum communication range:
Line of sight approx. 10 m1)
Frequency band:
2.4 GHz band (2.4000 GHz 
2.4835 GHz)
Modulation method:
FHSS
Compatible Bluetooth profiles2):
A2DP (Advanced Audio Distribution
Profile)
AVRCP (Audio Video Remote
Control Profile)
36GB
CD player section
System: Compact disc and digital audio
system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6µW
*This output is the value measurement
at a distance of 200mm from the
objective lens surface on the Optical
Pick-up Block with 7mm aperture.
Frequency response: 20 Hz  20 kHz
Signal-to-noise ratio: More than 90 dB
Dynamic range: More than 90 dB
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section:
Tuning range:
87.5  108.0 MHz (100 kHz step)
Antenna: FM lead antenna
Antenna terminals: 75 ohms unbalanced
Intermediate frequency: 10.7 MHz
AM tuner section:
Tuning range:
530  1,710 kHz (with 10 kHz tuning
interval)
531  1,710 kHz (with 9 kHz tuning
interval)
Antenna: AM loop antenna, external
antenna terminal
Intermediate frequency: 450 kHz
Speaker (SS-CBX20)
Speaker system: Full-range, bass-reflex, 10
cm, cone type
Rated impedance: 6 ohms
Dimensions (w/h/d): Approx. 140 × 245 ×
215 mm
Mass: Approx. 1.9 kg
General
Others
Power requirements: 120 V AC, 60 Hz
Power consumption: 63 watts
Dimensions (w/h/d) (excl. speakers):
Approx. 215 × 140 × 298 mm
Mass (excl. speakers): Approx. 3.9 kg
Supplied accessories: Remote Commander
(RM-AMU009) (1), R6 (Size AA) batteries
(2), AM loop antenna (1), FM lead antenna
(1), iPod Dock Adapters (1 set)
Design and specifications are subject to
change without notice.
Standby power consumption:
0.5 W
Halogenated flame retardants
are not used in the certain
printed wiring boards.
Halogenated flame retardants
are not used in cabinets.
(Except for the United States
model)
37GB
Bluetooth wireless
technology
Bluetooth wireless technology is a shortrange wireless technology linking digital
devices, such as personal computers and
digital still cameras. Using the Bluetooth
wireless technology, you can operate the
units involved within a range of about 10
meters.
The Bluetooth wireless technology is
commonly used between two devices,
but a single device can be connected to
multiple devices.
You do not need wires to get connected
as you do with a USB connection, and
you do not need to place the devices face
to face as you do with wireless infrared
technology. You can use the technology
with one Bluetooth device in your bag
or pocket.
Bluetooth wireless technology is a global
standard supported by thousands of
companies. These companies produce
products that meet the global standard.
Supported Bluetooth version and
profiles
Profile refers to a standard set of
capabilities for various Bluetooth product
capabilities. This system supports the
following Bluetooth version and profiles.
Supported Bluetooth version:
Bluetooth Standard version 2.0
Supported Bluetooth profiles:
A2DP (Advanced Audio Distribution
Profile)
AVRCP (Audio Video Remote
Control Profile)
38GB
Effective communication range
Bluetooth devices should be used within
approximately 10 meters (unobstructed
distance) of each other. The effective
communication range may become
shorter under the following conditions.
When a person, metal object, wall
or other obstruction is between the
devices with a Bluetooth connection
Locations where a wireless LAN is
installed
Around microwave ovens that are in
use
Locations where other electromagnetic
waves occur
Effects of other devices
Bluetooth devices and wireless LAN
(IEEE 802.11b/g) use the same frequency
band (2.4 GHz). When using your
Bluetooth device near a device with
wireless LAN capability, electromagnetic
interference may occur. This could result
in lower data transfer rates, noise, or
inability to connect. If this happens, try
the following remedies:
Try connecting this system and
Bluetooth mobile phone or Bluetooth
device when you are at least 10
meters away from the wireless LAN
equipment.
Turn off the power to the wireless LAN
equipment when using your Bluetooth
device within 10 meters.
Effects on other devices
The radio waves broadcast by this system
may interfere with the operation of some
medical devices. Since this interference
may result in malfunction, always turn
off the power on this system, Bluetooth
mobile phone and Bluetooth device in
the following locations:
In hospitals, on trains, in airplanes,
at gas stations, and any place where
flammable gasses may be present
Near automatic doors or fire alarms
Notes
Others
This system supports security functions that
comply with the Bluetooth specification
as a means of ensuring security during
communication using Bluetooth technology.
However, this security may be insufficient
depending on the setting contents and
other factors, so always be careful when
performing communication using Bluetooth
technology.
Sony cannot be held liable in any way
for damages or other loss resulting from
information leaks during communication
using Bluetooth technology.
Bluetooth communication is not necessarily
guaranteed with all Bluetooth devices that
have the same profile as this system.
Bluetooth devices connected with this system
must comply with the Bluetooth specification
prescribed by the Bluetooth SIG, Inc., and
must be certified to comply. However, even
when a device complies with the Bluetooth
specification, there may be cases where
the characteristics or specifications of the
Bluetooth device make it impossible to
connect, or may result in different control
methods, display or operation.
Noise may occur or the audio may
cut off depending on the Bluetooth
device connected with this system,
the communications environment, or
surrounding conditions.
39GB
Compatible devices
with this system
Bluetooth devices
You can check the websites below for the
Bluetooth compatible devices.
For customers in the U.S.A.:
<http://www.sony.com/shelfsupport>
For customers in Canada:
English <http://www.sony.ca/
ElectronicsSupport/>
French <http://fr.sony.ca/
ElectronicsSupport/>
For customers in Europe:
<http://support.sony-europe.com/>
For customers in Latin America:
<http://www.sony-latin.com/index.crp>
For customers in Asia and Oceania:
<http://www.sony-asia.com/support>
40GB
iPod models
You can use the following iPod models on this system. Update your iPod with the latest
software before using it.
iPod nano 3rd
generation
(video)
iPod classic
iPod nano 2nd
generation
(aluminum)
iPod 5th
generation
(video)
iPod nano 1st
generation
iPod 4th
generation
(color display)
iPod 4th
generation
Others
iPod touch
iPod mini
41GB
42GB
Others
43GB
Printed in China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising