- Computers & electronics
- Audio & home theatre
- Cassette players
- Sony
- SLV-XA147JE
- Operating instructions
advertisement
3-860-880-11 (1)
Video Cassette
Player
Operating Instructions
PAL NTSC
SLV-XA147JE/MJ/PS
SLV-XF247ME/PS
©1997 by Sony Corporation
WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
The mains lead must only be changed at a qualified service shop.
Precautions
Safety
• This unit operates on 110 – 240 V AC,
50/60 Hz. Check that the unit’s operating voltage is identical with your local power supply.
• If anything falls into the cabinet, unplug the unit and have it checked by qualified personnel before operating it any further.
• The unit is not disconnected from the mains as long as it is connected to the mains, even if the unit itself has been turned off.
• Unplug the unit from the mains if you do not intend to use it for an extended period of time. To disconnect the cord, pull it out by the plug, never by the cord.
Installing
• Allow adequate air circulation to prevent internal heat buildup.
• Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
• Do not install the unit near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, excessive dust, mechanical vibration or shock.
• Do not install the unit in an inclined position. It is designed to be operated in a horizontal position only.
• Keep the unit and cassettes away from equipment with strong magnets, such as microwave ovens or large loudspeakers.
• Do not place heavy objects on the unit.
• If the unit is brought directly from a cold to a warm location, moisture may condense inside the unit and cause damage to the video head and tape. When you first install the unit, or when you move it from a cold to a warm location, wait for about one hour before operating the unit.
Caution
Television programmes, films, video tapes, and other materials may be copyrighted.
Unauthorized recording of such material may be contrary to the provisions of the copyright laws. Also, use of this recorder with cable television transmission may require authorization from the cable television transmitter and/or programme owner.
Compatible colour systems
• This unit is designed to record and play back using the PAL (B/G and D/K),
MESECAM (B/G and D/K), NTSC 3.58, and
NTSC 4.43 colour systems. Recording of video sources based on other colour systems cannot be guaranteed.
• Tapes recorded with the NTSC colour system can be played back on this unit using a TV or a colour monitor for the PAL colour system.
• To play back tapes recorded with the PAL and MESECAM colour systems, you need a
TV or colour monitor compatible with these systems.
2 Introduction
Table of contents
Getting Started
4 Step 1: Unpacking
5 Step 2: Setting up the remote commander
6 Step 3: Connecting the unit
8 Step 4: Tuning your TV to the unit
Basic Operations
10 Playing a tape
Additional Operations
15 Playing/searching at various speeds
17 Adjusting the picture
18 Editing with another VCR
Additional Information
21 Troubleshooting
23 Specifications
24 Index to parts and controls back cover
Index
Introduction 3
Getting Started
Step 1
Unpacking
Check that you have received the following items with the unit:
• Remote commander • Audio/video cable (3-phono to 3phono) (SLV-XF247ME/PS only)
• R6 (Size AA) batteries
• Aerial cable
• Plug adaptor
(SLV-XA147JE/MJ and XF247ME only)
Checking your model name
The instructions in this manual are for the 5 models: SLV-XA147JE,
XA147MJ, XA147PS, XF247ME and XF247PS. Check your model number by looking at the rear panel of your unit. The SLV-XF247ME is the model used for illustration purposes. Any difference in operation is clearly indicated in the text, for example, “SLV-XA147JE only.”
4 Getting Started
Step 2
Setting up the remote commander
Inserting the batteries
Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment.
Using the remote commander
You can use this remote commander to operate the unit and a Sony TV. To operate this unit, point at the remote sensor on the unit. To operate the TV, point at the remote sensor on the TV.
Remote sensor
REC
TV/VIDEO
; (TV power) u
(on/standby)
PROG (CH) +/–
VOL +/–
To
Turn the TV to standby or active mode
Turn on the TV power
Increase (+) or decrease (–) the TV volume
Change the TV programme position
Select an input source of the TV either from aerial in or from line in
Press u (on/standby)
; (TV power)
VOL +/–
PROG (CH) +/–
TV/VIDEO
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not mix different types of batteries.
Getting Started 5
Step 3
Connecting the unit
AERIAL OUT
1
2
Aerial cable (supplied)
AERIAL IN to mains
: Signal flow
Disconnect the aerial cable from your TV and connect it to AERIAL IN on the rear panel of the unit.
AERIAL
OUT
IN
Connect AERIAL OUT of the unit and the aerial input of your TV using the supplied aerial cable.
AERIAL
OUT
IN
3
Connect the mains lead to the mains.
Use the supplied plug adaptor, if necessary, depending on the design of the mains (SLV-XA147JE/MJ and XF247ME only).
6 Getting Started
Additional connections
To a TV that has phono type audio/video input jacks
This additional connection improves picture and sound quality.
Connect the TV as shown on the right.
If you want to use the Trinitron TV
Synchro Play function (see page 14), this connection is necessary. (If your TV has two or more inputs, connect the audio/video cable to the VIDEO IN 1 jacks.)
To a stereo system (SLV-XF247ME/
PS only)
You can improve sound quality by connecting a stereo system as shown on the right.
For SLV-XA147JE/MJ/PS
This unit
AUDIO VIDEO
LINE IN
LINE OUT
IN
VIDEO
AUDIO
TV
Audio/video cable (not supplied)
For SLV-XF247ME/PS
This unit
AUDIO VIDEO
LINE 1 IN
LINE 1 OUT
IN
VIDEO
AUDIO
TV
Audio/video cable (supplied)
This unit
AUDIO VIDEO
LINE 1 IN
LINE 1 OUT
Stereo system
AUX IN
Audio cable (not supplied)
Getting Started 7
Step 4
Tuning your TV to the unit
If you have connected your unit to the TV using the audio/video cable, skip this step.
ON/STANDBY
REC
4
5
1
ON/STANDBY Press ON/STANDBY to turn on the unit.
2
3
Turn on your TV and select a programme position for video playback.
Choose a channel between UHF 30 and 39 on the TV where there is no picture and no sound or only a steady rustling sound.
This channel will now be referred to as the video channel.
Insert a tape recorded in the colour system matching your TV into the cassette compartment.
The unit starts playing automatically if you insert a tape with its safety tab removed.
Press · PLAY on the unit.
Tune the TV until the video playback picture is clearly displayed on the TV screen.
Refer to your TV manual for tuning instructions.
You have now tuned your TV to the unit. From now on, whenever you want to play a tape, set the TV to the video channel.
If the playback picture does not appear clearly, see “To obtain a clear playback picture” on page 9.
8 Getting Started
To obtain a clear playback picture
If the playback picture does not appear clearly in step 5 above, turn the RF CHANNEL screw on the rear panel of the unit with a screwdriver to a position where
RF CHANNEL the TV clearly displays the playback picture.
To select the TV system
For your TV to receive the correct signal from your unit, you must set the TV SYSTEM switch on the rear panel of the unit to either G
(for system B/G) or K (for system
D/K). If this switch is set to the wrong position, the sound will be distorted.
TV SYSTEM
G
K
Getting Started 9
Basic Operations
Playing a tape
6 EJECT
REC
NTSC PB
COLOR SYSTEM
1
2
3
PLAY
Turn on your TV and set it to the video channel.
Insert a tape.
The unit turns on, and starts playing automatically if you insert a tape with its safety tab removed.
REC
Press · PLAY.
When the tape reaches the end, it will rewind automatically.
3/#
SEARCH
P PAUSE
) FF
· PLAY p STOP
0 REW
10 Basic Operations
Additional tasks
To
Stop play
Press p STOP
Pause play
Resume play after pause P PAUSE or · PLAY
Search forward
P PAUSE
) FF or # SEARCH during playback
Search backward
Fast-forward the tape
Rewind the tape
Eject the tape
0
)
0
6
REW or 3 SEARCH during playback
FF during stop
REW during stop
EJECT
To set the colour system
If streaks appear during playback, set COLOR SYSTEM on the unit to conform to the system that the tape was recorded in. (Normally set the switch to AUTO.)
If your tape was recorded in
PAL
NTSC
MESECAM
Set COLOR SYSTEM to
PAL/MESECAM
NTSC
PAL/MESECAM
To play an NTSC-recorded tape
Set NTSC PB on the unit according to the colour system of your TV.
If your TV is
PAL
NTSC 4.43
NTSC 3.58
Set NTSC PB to
ON PAL TV
NTSC 4.43
NTSC 3.58
continued
Basic Operations 11
Playing a tape (continued)
Notes
• Depending on your TV, the following may occur while playing an NTSC-recorded tape:
– the picture is black and white,
– the picture shakes,
– no picture appears on the TV screen,
– black streaks appear horizontally on the TV screen, and
– the colour density increases or decreases.
• You can eject a tape even when the power is off. When you press 6 EJECT, the unit turns on automatically. After ejecting the tape, the unit turns off again.
• When the pause mode lasts for more than approximately five minutes, the unit will automatically enter the playback mode.
• (SLV-XA147PS and XF247ME/PS only)
You can play back tapes recorded in the SP mode only.
• (SLV-XA147JE/MJ only)
You can play back tapes recorded in the SP, LP, and EP mode.
12 Basic Operations
Selecting the sound during playback
(SLV-XF247ME/PS only)
Press AUDIO MONITOR to select the sound you want. Each press of the button changes the indicator in the display window.
When you play a tape recorded in stereo or with a bilingual sound track, the Hi-Fi Stereo indicator in the display window lights up.
AUDIO
MONITOR
To listen to a
Stereo tape’s Bilingual tape’s
Press AUDIO MONITOR until the display window indicator shows
Stereo sound
Left channel
Main and sub sounds
Main sound
L/R
L
Right channel
Standard sound* 1
Sub sound
Standard sound* 2
R
No indication
* 1 Usually the mixed sound of left and right channels (monaural)
* 2 Usually the main sound (monaural)
How sound is recorded on a video tape
The unit records sound onto two separate tracks. Hi-fi audio is recorded onto the main track along with the picture. Monaural sound is recorded onto the normal audio track along the edge of the tape.
Stereo
Usually mixed left/right channels
Bilingual
Usually main sound
Normal audio track
(monaural)
Hi-fi audio track
(main track)
Stereo sound
(left/right channels)
Main (left channel)
Sub (right channel)
Notes
• To listen to playback sounds in stereo, you must use the AUDIO OUT connections.
• When you play back a tape recorded in monaural, the sound is heard in monaural regardless of the AUDIO MONITOR setting.
• You cannot select the sound to listen to while recording.
continued
Basic Operations 13
Playing a tape (continued)
Turning on the unit and TV, and starting playback automatically (Trinitron TV Synchro Play)
You can only use this function if your TV is made by Sony (Trinitron TV).
How to connect to use this function
Connect the unit and TV with the audio/video cable (see “To a TV that has phono type audio/video input jacks” on page 7). Be sure to connect the audio/video cable to the VIDEO IN 1 jacks on the TV if the TV has two inputs or more. The TV must be placed where it will respond to the remote commander while you are pointing it at the unit.
Operation
Make sure that the TV’s power is in standby mode.
Press TRINITRON TV SYNCHRO PLAY and hold the remote commander in place for about two seconds.
The unit and TV turn on, and the TV is set to the video channel. If there is a tape in the unit, playback starts automatically.
Notes
• If the Trinitron TV Synchro Play function does not work properly:
- Wait a few moments, and press the button again.
- Replace both of the batteries in the remote commander with new ones, and press the button again.
Note that this function may not operate some Sony TVs because of the remote commander’s signal limitations.
• Do not press TRINITRON TV SYNCHRO PLAY while playing back a video tape. If you do so, the TV’s input source will momentarily switch to the TV’s tuner.
14 Basic Operations
Additional Operations
Playing/searching at various speeds
· PLAY
0 3 REW ) # FF
SLOW +/–
3 /#
SEARCH
7 FRAME
) FF
· PLAY
0 REW
REC
Playback options
Fast-forward/rewind
View the picture during fastforward or rewind
Play at high speed
Play in slow motion
Play frame by frame
Rewind and start play
Operation
During stop, press ) FF or 0 REW.
During fast-forward, hold ) FF down. During rewind, hold 0 REW down.
During playback or pause, press # SEARCH or 3 SEARCH .
During playback or pause, press SLOW+/–. Press the +/– buttons to change the speed.
During pause, press 7 FRAME to advance the picture one frame. Hold the button down to play one frame each second.
During stop, hold 0 3 REW on the unit down and press
· PLAY on the unit.
continued
Additional Operations 15
Playing/searching at various speeds (continued)
To resume normal playback
Press · PLAY.
Tip
• If the picture shakes while in the still mode, adjust the picture using
$ /4 TRACKING NORMAL/SLOW STILL ADJUST.
Notes
• Streaks or snow cannot be eliminated completely in the various playback operations, especially in the slow motion mode.
• The sound is muted during these operations.
• If you press 7 FRAME during playback, playback continues at the normal speed but the sound is muted. Press · PLAY to resume normal playback.
• In the LP mode, you may see static or there may be no colour (SLV-XA147JE/MJ only).
16 Additional Operations
Adjusting the picture
Adjusting the tracking
TRACKING
Although the unit automatically adjusts the tracking when playing a tape, distortion may occur if the tape was recorded in poor condition. If so, manually adjust the tracking.
AUTO/MANU
$ /4
TRACKING
Press $/4 TRACKING
NORMAL/SLOW to obtain the best possible picture. The
NORMAL/
SLOW distortion should disappear as you press one of the two buttons. If you cannot get a clear picture with manual adjustment, press TRACKING AUTO/MANU to return to automatic adjustment.
About OPC
OPC (Optimum Picture Control) automatically improves playback quality by adjusting the unit to the condition of the video heads and tape.
The OPC function automatically works on all types of tapes, including rental tapes and the tapes that were not recorded with OPC.
Notes
• The auto tracking function works automatically when you play back a tape just after inserting it.
• Sufficient picture quality may not be obtained when playing back tapes recorded on another VCR or tapes in poor condition.
• When a tape recorded with the copyguard system is played back, intermittent distortion may appear in the upper portion of the picture. However, this is not a malfunction of the unit.
Additional Operations
17
Editing with another VCR
How to connect to record on this unit
This unit (Recorder) TV
LINE 1 IN
Other VCR (Player)
LINE OUT
: Signal flow
Audio/video cable (not supplied)
Tips
• (SLV-XA147JE/MJ/PS only)
Use a commercially available 2-phono to 2-phono type audio/video cable. If the other VCR has AUDIO L and R jacks, use a commercially available 3-phono to 2phono type audio/video cable.
• (SLV-XF247ME/PS only)
- If the other VCR is a monaural type, use a commercially available 3-phono to 2phono type audio/video cable.
- You can also use the LINE 2 IN jacks on the front of the unit.
Notes
• Make sure you connect the plugs to the jacks of the same colour.
• When connecting the units, do not simultaneously connect the LINE IN and LINE
OUT jacks on your unit with the other VCR. A humming noise may occur if you do this.
18 Additional Operations
Operation (when recording on this unit)
You can make a copy of a tape using this unit for recording or playback.
The unit cannot record TV programmes directly since it does not have a TV tuner.
Before you start editing
• Turn on your TV and set it to the video channel.
SLV-XF247ME/PS
INPUT SELECT
SLV-XA147JE/MJ
REC
P PAUSE
P PAUSE r REC
1
(SLV-XF247ME/PS only)
Set INPUT SELECT to LINE 1
(or LINE 2).
2
(SLV-XA147JE/MJ only)
Set TAPE SPEED to select the tape speed (SP or LP for the PAL colour system, and SP or EP for the NTSC colour system).
REC
TAPE SPEED r REC
LP provides a recording time twice as long as SP. EP provides a recording time three times as long as SP. However, SP produces better picture quality.
3
Insert a source tape with its safety tab removed into the other
(playback) VCR. Search for the point to start playback and set it to playback pause.
4
Insert a tape with its safety tab in place into this (recording) unit.
Search for the point to start recording and press P PAUSE.
5
Press r REC on this unit to set it to recording pause.
6
To start editing, press the P PAUSE buttons on both units at the same time.
To stop editing
Press the p STOP buttons on both units.
continued
Additional Operations
19
Editing with another VCR (continued)
To save a recording
To prevent accidental erasure, break off the safety tab as illustrated. To record on a tape again, cover the tab hole with adhesive tape.
Safety tab
Tips
• To edit more precisely, press the P PAUSE buttons on the units to release pause.
• To cut out unwanted scenes while editing, press P PAUSE on this unit when an unwanted scene begins. When that scene ends, press P PAUSE again to resume recording.
Note
• (SLV-XA147PS and XF247ME/PS only)
You can record tapes only in SP mode.
20 Additional Operations
Additional Information
Troubleshooting
If you have any questions or problems not covered below, please consult your nearest Sony service facility.
Symptom Remedy
• Connect the mains lead securely.
The ON/STANDBY switch does not function.
The power is turned on but the unit does not operate.
The VCR enters standby mode or turns off automatically.
The playback picture does not appear on the TV screen.
The picture is not clear.
• Moisture condensation occurs. Turn the power off, unplug the mains lead and leave the unit to dry for over an hour.
• The auto safety system is triggered to protect your tape and the unit’s mechanism when there is something wrong with the tape or when the mechanism is overloaded. Press ON/STANDBY to restart the unit.
If the unit does not work after pressing ON/STANDBY again, disconnect the mains lead from the mains. Wait for at least 15 seconds. Then reconnect mains, and press ON/STANDBY again. If the unit still does not work, please consult your nearest Sony service facility.
• Make sure the TV is set to the video channel. If you are using a monitor, set it to video input.
• Adjust the tracking with the $/4 TRACKING
NORMAL/SLOW buttons.
• Make sure the COLOR SYSTEM switch is set to the position corresponding to the colour system which the tape was recorded with.
• The video heads are dirty (see the next page). Clean the video heads using a video head cleaning cassette.
If a cleaning cassette is not available in your area, have the heads cleaned at your nearest Sony service facility
(a standard service charge will be required). Do not use a commercially available wet-type cleaning cassette, as it may damage the video heads.
• The video heads may have to be replaced. Consult your local Sony service facility for more information.
• Adjust the vertical hold control on the TV or monitor.
The picture rolls vertically during picture search.
The picture has no sound.
• The tape is defective. Use a new tape.
continued
Additional Information 21
Troubleshooting (continued)
Symptom
The tape starts playing as soon as it is inserted.
The tape is ejected when you press r REC.
Nothing happens when you press r REC.
No tape can be inserted.
The remote commander does not function.
The unit needs to be cleaned.
Remedy
• The safety tab has been removed. To record on this tape, cover the tab hole.
• Check that the safety tab has not been removed.
• Make sure the tape is not at its end.
• (SLV-XF247ME/PS only)
Select the correct source with the INPUT SELECT switch, LINE 1 or LINE 2.
• Check that a tape isn’t already in the tape compartment.
• Make sure you are pointing the remote commander at the remote sensor on the unit.
• Replace all the batteries in the remote commander with new ones if they are weak.
• Clean the cabinet, panel, and controls with a dry soft cloth, or a soft cloth slightly moistened with a mild detergent solution. Do not use any type of solvent, such as alcohol or benzine.
Auto head cleaner
The unit incorporates an auto head cleaner which cleans the video heads when a tape is loaded or unloaded. When the heads are not sufficiently clean, even after a tape has been loaded/unloaded several times, use a video head cleaning cassette.
Symptoms caused by contaminated video heads
• Normal picture • Rough picture • Unclear picture • No picture (or black & white screen appears) initial terminal
Sapphire tape cleaner
The unit incorporates a sapphire tape cleaner which cleans a video tape when it is loaded. This cleaner can prevent the video heads from contamination by removing dust or mold from a tape with the sapphire edge.
22
Additional Information
Specifications
System
RF output signal
UHF channels 30 to 39
Aerial out
75-ohm asymmetrical aerial socket
Inputs and outputs
LINE IN (SLV-XA147JE/MJ/PS)
LINE 1 IN/LINE 2 IN (SLV-XF247ME/PS)
VIDEO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms, unbalanced, sync negative
AUDIO IN, phono jack (1) (SLV-XA147JE/MJ/PS) phono jack (2) (SLV-XF247ME/PS)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
LINE OUT (SLV-XA147JE/MJ/PS)
LINE 1 OUT (SLV-XF247ME/PS)
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms, unbalanced, sync negative
AUDIO OUT, phono jack (1) (SLV-XA147JE/MJ/PS) phono jack (2) (SLV-XF247ME/PS)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
General
Power requirements
110 – 240 V AC, 50/60 Hz
Power consumption
10 W
Operating temperature
5°C to 40°C
Storage temperature
–20°C to 60°C
Dimensions
Approx. 355
×
100
×
280 mm (w/h/d)
Mass including projecting parts and controls
Approx. 3.8 kg
Supplied accessories
Remote commander (1)
R6 (Size AA) batteries (2)
Aerial cable (1)
Audio/video cable (3-phono to 3-phono)
(SLV-XF247ME/PS only) (1)
Plug adaptor
(SLV-XA147JE/MJ and XF247ME only) (1)
Design and specifications are subject to change without notice.
Additional Information 23
Index to parts and controls
Refer to the pages indicated in parentheses ( ) for details.
Front panel (SLV-XA147JE/MJ/PS)
REC
Front panel (SLV-XF247ME/PS)
REC
1 ON/STANDBY switch/indicator (8)
2 LINE 2 IN VIDEO/AUDIO L/R jacks
(SLV-XF247ME/PS only) (18)
3 Tape compartment
4 Hi-Fi Stereo/L/R indicators (SLV-
XF247ME/PS only) (13)
5 Tape operation indicators
6 03 REW button (11, 15)
7 · PLAY button (10)
8 )# FF button (11, 15)
9 r REC button (19)
24
Additional Information
!º p STOP button (11)
!¡ P PAUSE button (11)
!™ NTSC PB switch (11)
!£ COLOR SYSTEM switch (11)
!¢ REC (recording) indicator
!∞ TAPE SPEED switch (SLV-XA147JE/
MJ only) (19)
!§ Remote sensor (5)
!¶ INPUT SELECT switch (SLV-
XF247ME/PS only) (19)
!• § EJECT button (11)
Rear panel (SLV-XA147JE/MJ/PS)
Rear panel (SLV-XF247ME/PS)
1 Mains lead (6)
2 RF CHANNEL screw (9)
3 AERIAL OUT connector (6)
4 LINE IN VIDEO/AUDIO jacks
(SLV-XA147JE/MJ/PS only) (18)
LINE 1 IN VIDEO/AUDIO L/R jacks (SLV-XF247ME/PS only) (18)
5 LINE OUT VIDEO/AUDIO jacks
(SLV-XA147JE/MJ/PS only) (7)
LINE 1 OUT VIDEO/AUDIO L/R jacks (SLV-XF247ME/PS only) (7)
6 AERIAL IN connector (6)
7 TV SYSTEM switch (9) continued
Additional Information 25
Index to parts and controls (continued)
Remote commander
1 6 EJECT button (11)
2 TV control buttons (Only for TV) (5)
TV/VIDEO
; (TV power) u (on/standby)
VOL +/–
PROG (CH) +/–
3 EFFECT button (This button doesn’t
work with this unit.)
4 TRACKING AUTO/MANU button
(17)
5 TV/VTR button (This button doesn’t
work with this unit.)
6 r REC button (19)
7 AUDIO MONITOR button (This button works only for SLV-XF247ME/
PS.) (13)
8 P PAUSE button (11)
9 0 REW button (11, 15)
0 · PLAY button (10)
!¡ p STOP button (11)
!™ TRINITRON TV SYNCHRO PLAY button (14)
!£ u (on/standby) switch (8)
!¢ $/4 TRACKING NORMAL/SLOW
STILL ADJUST buttons (17)
!∞ SLOW +/– buttons (15)
!§ =/+ AMS buttons (These
buttons don’t work with this unit.)
!¶ 3/# SEARCH buttons (11, 15)
!• 7 FRAME button (15)
!ª ) FF button (11, 15)
26
Additional Information
Additional Information 27
Index
A, B
Accessories supplied 4
Adjusting picture 17 tracking 17
Aerial hookup 6
Audio track 13
Auto head cleaner 22
AV connection 7
C
Cleaning the video heads 21
Colour system compatible colour systems 2 setting 11
Connecting the unit and your TV 6 to a TV with audio/ video jacks 7
D
Dubbing. See Editing
E, F, G
Editing 18
EP mode 12, 19
H, I, J, K
Hi-fi audio track 13
L
LP mode 12, 19
M
Monitoring during playback 13
N
Normal audio track 13
NTSC-recorded tapes 11
O
OPC (Optimum Picture
Control) 17
P, Q
Picture adjustment. See
Adjusting
Playback 10 at various speeds 11, 15 frame-by-frame 15 slow motion 15
R
Recording 19
Remote commander 5
RF CHANNEL screw 9
S
Safety tab 20
Searching at various speeds 15
SP mode 12, 19
T, U, V, W, X, Y, Z
Tracking adjustment. See
Adjusting
Trinitron TV Synchro
Play 14
Tuning your TV to the unit 8
TV system 9
Sony Corporation
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project