Innovation, Quality, Performance

11-

STYLED

LED-7474

User Manual

Professional Entertainment Technolog

TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification

3. Installation

4. How to Control the Unit

4.1 Control Panel

4.2 Master/Slave operation

4.3 Easy controller CA-8

4.4 Universal DMX controller

5. DMX 512 Configuration

6. DMX 512 Connection

7. Troubleshooting

8. Fixture Cleaning

1-

EC - Declaration of Conformity

We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the

Electromagnetic Compatibility (EMC) Directive 89/336/EEC.

EN55014-2: 1997 A1: 2001, EN61000-4-2: 1995; EN61000-4-3: 2002;

EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6: 1996,

EN61000-4-11: 1994.

&

Harmonized Standard

EN60598-1: 2000+ALL: 2000+A12: 2002

Safety of household and similar electrical appliances

Part 1: General requirements

10-

8. Fixture Cleaning

The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit’s optics. y Clean with soft cloth using normal glass cleaning fluid. y Always dry the parts carefully. y Clean the external optics at least every 20 days. Clean the internal optics at least every

30/60 days.

9-

1. Safety Instruction

Please read the instruction carefully which including important information about the installation, operation and maintenance.

WARNING y Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet. y Unpack and check carefully there is no transportation damage before using the fixture. y It’s important to ground the yellow/green conductor to earth in order to avoid electric shock. y Disconnect main power before servicing and maintenance. y Maximum ambient temperature is Ta : 40℃. Don’t operate it where the temperature is higher than this. y In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts. y Do not connect the device to any dimmer pack. y Do not touch any wire during operation and there might be a hazard of electric shock. y To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture. y The housing must be replaced if they are visibly damaged. y Do not look directly at the LED light beam while the fixture is on. y There are no user serviceable parts inside the fixture. Do not open the housing or attempt any repairs by yourself. In the unlikely event your fixture may require service, please contact your nearest dealer. y Due to the magnifying type lens, please keep the lens out of contact with direct sunlight.

Direct sunlight can cause heat to build up inside of the unit, which will seriously damage unit.

For power supply, do not connect in series much more than 51 units, use another mains supply for next 51 units.

2-

2. Technical Specification

y Featuring 4 LED clusters & great programs, styled rocks the crowds with dynamic scanning effects and powerful beams. y 3 Operation Modes: DMX, Master/Slave, Sound Activation. y Optional CA-8 easy controller for enjoying instant lighting shows at your fingertips. y Low heat, low power consumption; No duty cycle, run all night. y Dip-switch for setting DMX address. y Perfect for discos, clubs, pubs, parties and mobile DJs. y Voltage: AC 100V~240V 50/60Hz y Fuse: T 6.3A y Power Consumption: 12W y LED: total: 256, Red: 96pcs, Green: 96pcs, Blue: 64pcs y Dimension: 965 x 190 x 185mm y Weight: 6.3kgs

3. Installation

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture.

The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.

3-

7. Troubleshooting

Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting:

A. The fixture does not work, no light

1. Check the connection of power and main fuse.

2. Measure the mains voltage on the main connector.

B. Not responding to DMX controller

1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.

2. If the DMX LED is on and no response to the channel, check the address settings and

DMX polarity.

3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the fixture or the previous one.

4. Try to use another DMX controller.

5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.

C. Some fixtures don’t respond to the easy controller

1. You may have a break in the DMX cabling.

2. Wrong DMX address in the fixture. Set the proper address.

D. No response to the sound

1. Make sure the fixture does not receive DMX signal.

2. Check microphone to see if it is good by tapping the microphone.

E. One of the channels is not working well

1. The stepper motor might be damaged or the cable connected to the PCB is broken.

2. The motor’s drive IC on the PCB might be out of condition.

8-

6. DMX 512 Connection

The DMX 512 is widely used in intelligent lightings and with a maximum of 512 channels.

4. How To Control The Unit

4.1 Control Panel

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit.

3. Connect the unit together in a ‘daisy chain’ by XLR plug from the output of the unit to the input of the next unit. The cable can not be branched or split to a ‘Y’ cable.

DMX 512 is a very high-speed signal. Inadequate or damaged cables, solder joints or corroded connectors can easily distort the signal and shut down the system.

4. The DMX output and input connectors are pass-through to maintain the DMX circuit, when power is connected to the unit.

5. Each lighting unit needs to have an address set to receive the data sent by the controller. The address number is between 0-512 (usually 0 & 1 are equal to 1).

6. The end of the DMX 512 system should be terminated to reduce signal errors.

7. 3 pin XLR connectors are more popular than 5 pin XLR.

3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)

Pin 4/5: Not used.

7-

○

Stand by, Function and Mode function.

4.2 Master/Slave Operation

The unit can be linked together in daisy chain as many as you need in master/slave mode to perform the great built-in pre-programmed lighting shows triggered by music.

In Master/Slave mode refer to the DMX settings below:

Master unit: Set all DIP switchs to OFF

Slave 1: Set DIP switch 1 to ON

2-light show: Set DIP switch 1 and 10 to ON

In order to create a great light show, you can set dip switch 10 ”on” on any unit that is linking to the master unit to get contrast movement to the master unit, even if you have two units only. Dipswitch 10 on the first (Master) unit is no use for the 2-light show as it is the master unit that operates the light show.

4-

4.3 Easy Controller (by CA-8)

The easy remote control is used only in master/slave mode. By connecting to the 1/4” microphone jack of the first unit, you will find that the remote controller on the first unit will control all the other units for Stand by, Function and Mode selection

Stand by

Function

Mode

Blackout the unit

1. Synchronous Strobe

2. Sound Strobe

3. Two light Strobe

Strobe (LED OFF)

Select show

1-12

Show (LED ON)

4.4 DMX Controller

When using a universal DMX controller to control the chain of units, you have to set DMX address by Dip switches from 1 to 9 to make sure all the units will receive its DMX signal.

The dip switch 10 is used to choose channel mode. Please refer to the following diagram to know how to address your DMX 512 system in the binary code.

DMX 512 Address Chart:

Dip-switches # 1 # 2 # 3 # 4 # 5 # 6 # 7 # 8 # 9

Value 1 2 4 8 16 32 64 128 256

• Examples:

Set dip switch 10 to ON, the unit is in 1 channel mode

Unit 1：dip / on: #1 (=1)

Unit 2：dip / on: #2 (=2)

Unit 3：dip / on: #1, #2, (1+2=3)

Unit 4：dip / on: #3 (=4)

#10

5-

Set dip switch 10 to OFF, the unit is in 6 channels mode

Unit 1：dip / on: #1 (=1)

Unit 2：dip / on: #1, # 2, #3 (1+2+4=7)

Unit 3：dip / on: #1, #3, #4 (1+4+8=13)

Unit 4：dip / on: #1, #2, #5 (1+2+16=19)

5. DMX 512 Configuration

1 & 6-CH modes:

6-