GeoVision Cube Camera, Mini Fixed Dome, Mini Fixed Rugged Dome, EFD 1100, EFD 2100, EFD 4700 Target Mini Fixed Dome, EDR 1100, EDR 2100, EDR 4700 Target Mini Fixed Rugged Dome Hardware Manual

GV-IPCam

Hardware Manual

Cube Camera

Mini Fixed Dome

Mini Fixed Rugged Dome

Target Mini Fixed Dome

Target Mini Fixed Rugged Dome

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

ICH265HISIV106-A

Caution

Risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteries according to the instructions.

Safety Notice

The GV-IPCAM uses a Lithium battery as the power supply for its internal real-time clock (RTC). The battery should not be replaced unless required!

If the battery does need replacing, please observe the following:

•

Danger of Explosion if battery is incorrectly replaced

•

Replace only with the same or equivalent battery, as recommended by

• the manufacturer

Dispose of used batteries according to the manufacturer's instructions

© 2017 GeoVision, Inc. All rights reserved.

Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of GeoVision.

Every effort has been made to ensure that the information in this manual is accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind and assumes no responsibility for errors or omissions. No liability is assumed for incidental or consequential damages arising from the use of the information or products contained herein. Features and specifications are subject to change without notice. Note: no memory card slot or local storage function for Argentina.

GeoVision, Inc.

9F, No. 246, Sec. 1, Neihu Rd.,

Neihu District, Taipei, Taiwan

Tel: +886-2-8797-8377

Fax: +886-2-8797-8335 http://www.geovision.com.tw

Trademarks used in this manual: GeoVision, the GeoVision logo and GV series products are trademarks of GeoVision, Inc.

February 2017

Contents

Contents ..............................................................................i

Options ............................................................................. iv

Note for USB Storage and WiFi Adapter ....................... vi

Note for Installing Camera Outdoor.............................. vii

Chapter 1 Mini Fixed Dome (Part I) & Mini Fixed

Rugged Dome.....................................................................1

1.1 Packing List ..............................................................................4

1.2 Features ...................................................................................6

1.3 Overview ..................................................................................9

1.3.1 GV-MFD120 / 130 / 320 ................................................9

1.3.2 GV-MFD1501 Series / 2401 Series / 2501 Series / 3401

Series / 5301 Series ............................................................11

1.3.3 GV-MDR .....................................................................13

1.4 Installation ..............................................................................16

1.4.1 GV-MFD Series...........................................................16

1.4.2 GV-MDR Series ..........................................................18

1.5 Connecting the Camera...........................................................23

1.5.1 Wire Definition ............................................................23

1.5.2 Power and Network Connection ..................................24

1.5.3 Vehicle Installation ......................................................25

1.6 Loading Factory Default..........................................................26

Chapter 2 Mini Fixed Dome (Part II) ..............................27

2.1 Packing List ............................................................................28

2.2 Features .................................................................................29

2.3 Overview ................................................................................31

i

2.4 Installation ..............................................................................33

2.5 Connecting the Camera..........................................................36


Chapter 3 Target Mini Fixed Dome................................39

3.1 Packing List ............................................................................40

3.2 Features .................................................................................41

3.3 Overview ................................................................................43

3.4 Installation ..............................................................................45



Chapter 4 Target Mini Fixed Rugged Dome .................50

4.1 Packing List ............................................................................51

4.2 Features .................................................................................53

4.3 Overview ................................................................................55

4.4 Installation ..............................................................................56



Chapter 5 Cube Camera .................................................65

5.1 Packing List ............................................................................66

5.2 Features .................................................................................67

5.3 Overview ................................................................................68

5.4 Installation ..............................................................................69



Chapter 6 Advanced Cube Camera...............................73

6.1 Packing List ............................................................................74

6.2 Features .................................................................................75

6.3 Overview ................................................................................76

6.4 Installation ..............................................................................78

ii



iii

Options

Optional devices can expand your camera’s capabilities and versatility.

Contact your dealer for more information.

Device Description

Power Adapter

GV-PA191 PoE

Adapter

GV-POE Switch

GV-Mount

Accessories

The power adapter is available for all Mini Fixed

Dome, Cube Camera, and Advanced Cube Camera.

Contact your sales representative for the countries and areas supported.

The GV-PA191 PoE adapter is designed to provide power and network connection to the cameras over a single Ethernet cable.

The GV-POE Switch is designed to provide power along with network connection for IP devices. The

GV-POE Switch is available in various models with different numbers and types of ports.

The GV-Mount Accessories provide a comprehensive lineup of accessories for installation on ceiling, wall corner and pole. For details, see GV-

Mount Accessories Installation Guide on the

Software DVD.

GV-WiFi Adapter

The GV-WiFi Adapter is a plug-and-play device designed to connect GV-MFD1501 series / 2401 series / 2501 series / 3401 series / 5301 series to wireless network. This product complies with IEEE

802.11 b/g/n (Draft 3.0) standards for wireless networking. iv

Device

Plastic PG21

Conduit

Connector

GV-Relay V2

Description

The plastic PG21 conduit connector is used for running the wires of Target Mini Fixed Rugged

Dome through a 1/2” conduit pipe.

The connector is not supported by GV-EFD4700 and

GV-MFD2700 Series / 4700 Series.

Only supported by GV-MFD2700 Series / 4700

Series. The GV-Relay V2 is designed to expand the voltage load of GV IP devices. It provides 4 relay outputs, and each can be set as normally open (NO) or normally closed (NC) independently as per your requirement. v

Note for USB Storage and WiFi

Adapter

Mind the following limitations and requirements for using USB storage and

GV-WiFi Adapter:

1. The USB hard drive must be of 2.5’’ or 3.5’’, version 2.0 or above.

2. The USB hard drive’s storage capacity must not exceed 2TB.

3. USB flash drives and USB hubs are not supported.

4. External power supply is required for the USB hard drive.

5. To connect a GV-WiFi Adapter, make sure it is connected before the camera is powered on. vi

Note for Installing Camera Outdoor

When installing Mini Fixed Rugged Dome outdoor, be sure that:

1. The camera is set up above the junction box to prevent water from entering the camera along the cables.

2. Any PoE, power, audio and I/O cables are waterproofed using waterproof silicon rubber or the like.

3. The silica gel bag loses its effectiveness when the dry camera is opened. To prevent the lens from fogging up, replace the silica gel bag every time you open the camera, and conceal the gel bag in camera within 2 minutes of exposing to open air. vii

1

Mini Fixed & Rugged Dome

Chapter 1 Mini Fixed Dome (Part I)

& Mini Fixed Rugged Dome

The Mini Fixed Dome (GV-MFD) and Mini Fixed Rugged Dome (GV-MDR) are fixed, mini-sized ceiling-mount network cameras.

The GV-MDR series is designed for outdoor surveillance, conforming to

IK10 and IP67 standards. The camera is adjustable in 3 axis (pan, tilt and rotate) and can be connected through PoE.

The GV-MFD series is designed for indoor surveillance. Adjustable in 2 axis (pan and tilt), the camera also supports PoE.

The super low lux models can provide color live view in near darkness and the WDR Pro models can process scenes of contrasting intensity of lights. For details, see 1.2 Features.

1

Mini Fixed Dome (GV-MFD)

Model No.

GV-MFD120

GV-MFD130

GV-MFD320

Specifications

Fixed Iris, f: 4 mm,

F/1.5, 1/3’’ M12

Mount

Fixed Iris, f: 2.54 mm, F/2.8, 1/2.5’’

M12 Mount

GV-MFD1501-0F

GV-MFD2401-0F

GV-MFD2501-0F

GV-MFD3401-0F

GV-MFD5301-0F

Fixed Iris, f: 2.8 mm,

F/2.0, 1/3’’ M12

Mount

GV-MFD1501-1F

GV-MFD2501-1F


F/1.5, 1/3’’ M12

Mount

GV-MFD1501-2F

GV-MFD2401-2F

GV-MFD2501-2F

GV-MFD3401-2F

GV-MFD5301-2F

GV-MFD1501-3F

GV-MFD2401-3F

GV-MFD2501-3F

GV-MFD3401-3F

GV-MFD5301-3F

Fixed

Lens


F/1.6, 1/3’’ M12

Mount


F/1.6, 1/3’’ M12

Mount

GV-MFD1501-4F

GV-MFD2401-4F


F/1.8, 1/3’’ M12

Mount

GV-MFD1501-5F

GV-MFD2401-5F

GV-MFD2501-5F

GV-MFD3401-5F

GV-MFD5301-5F


F/1.8, 1/3’’ M12

Mount

Description

1.3 MP Low Lux,

H.264, Color

1.3 MP / 2 MP / 3

MP / 5MP, H.264,

Color

1.3 MP Super

Low Lux / 2 MP /

2 MP Super Low

Lux / 3 MP / 5

MP, H.264, Color

2

1


Model No.

GV-MFD2501-6F

GV-MFD3401-6F

Fixed

Lens

Specifications

Fixed Iris, f: 2.3mm,

F/2.2, 1/3’’ M12

Mount

Mini Fixed Rugged Dome (GV-MDR)

Model No.

GV-MDR220

GV-MDR320

GV-MDR520

GV-MDR1500-1F

GV-MDR3400-1F

GV-MDR5300-1F

GV-MDR1500-2F

GV-MDR3400-2F

GV-MDR5300-2F

Fixed

Lens

Specifications

Fixed Iris, f: 2.54 mm, F/2.8, 1/2.5’’

M12 Mount

Fixed Iris, f: 2.8 mm, F/2.0, 1/3’’

M12 Mount

Fixed Iris, f: 3.8 mm, F/1.8, 1/3’’

M12 Mount

Description

2 MP Super Low

Lux / 3 MP WDR

Pro, H.264, Color

Description

2 MP / 3 MP / 5MP,

H.264, Color

1.3 MP super low lux / 2 MP WDR

Pro / 2 MP super low lux / 3 MP

WDR Pro / 5 MP,

H.264, Color

3

1.1 Packing List

GV-MFD

• Self Tapping Screw x 2

• Screw Anchor x 2

• 2-pin terminal block (for GV-MFD120 / 130 / 320)

• Short-Body RJ-45 Plug (for GV-MFD1501 series / 2401 series /

2501 series / 3401 series / 5301 series)

• USB / Audio Y-cable (for GV-MFD1501 series / 2401 series /

2501 series / 3401 series / 5301 series)

• GV-IPCAM H.264 Software DVD

Note: The power adapter can be excluded upon request.

4

GV-MDR

• Mini Fixed Rugged Dome

• Self Tapping Screw x 2


1


• Silica gel bag x 2

• Adhesive Tape for Silica Gel Bag x 2

• Ferrite core for vehicle installation

• GV-IPCAM H.264 Software DVD

Note:

1. The power adapter can be excluded upon request.

2. When purchasing GV-MDR1500 / 3400 / 5300, choose one of the two LAN connector types (for motor vehicles or for general use). For details, see LAN Connector, 1.3.3 GV-MDR.

5

1.2 Features

GV-MFD

Camera Model

GV-MFD120

Image Sensor

1/3’’ progressive scan low lux CMOS

GV-MFD130

GV-MFD320

1/2.5’’ progressive scan CMOS

GV-MFD1501 series

GV-MFD2501 series

1/3’’ progressive scan super low lux

CMOS

1/2.8’’ progressive scan super low lux

CMOS

GV-MFD2401 series

GV-MFD3401 series


GV-MFD5301 series 1/2.5’’ progressive scan CMOS

GV-MDR

Camera Model Image Sensor

GV-MDR1500 Series

1/3’’ progressive scan super low lux

CMOS

GV-MDR220

GV-MDR320

GV-MDR520

GV-MDR5300 Series


GV-MDR3400 Series 1/3.2’’ progressive scan CMOS

• Dual streams from H.264 or MJPEG

• Frame rate

6

1


GV-MFD

Camera Model

GV-MFD120

GV-MFD130

GV-MFD1501 series

GV-MFD2401 series

GV-MFD2501 series

GV-MFD320

GV-MFD3401 series

GV-MFD5301 series

Frame Rate

Up to 30 fps at 1280 x 1024

Up to 30 fps at 1920 x 1080

Up to 20 fps at 2048 x 1536

Up to 10 fps at 2560 x 1920

GV-MDR

Camera Model Frame Rate

GV-MDR1500 series Up to 30 fps at 1280 x 1024

GV-MDR220 Up to 30 fps at 1920 x 1080

GV-MDR320

GV-MDR3400 series

GV-MDR520

GV-MDR5300 series

Up to 20 fps at 2048 x 1536

Up to 10 fps at 2560 x 1920

• Day and night function (electronic)

• Wide Dynamic Range (WDR)

• Wide Dynamic Range Pro (WDR Pro for GV-MFD2401 series / 3401 series and GV-MDR3400 series)

• Defog

• Vandal resistance (IK10 for metal casing, GV-MDR series only)

• Ingress protection (IP67 for GV-MDR series only)

• EN50155 compliance for rolling stock applications (for GV-MDR series only)

• Endurable to low environment temperatures (-30°C ~ 50°C / -22°F ~

122°F) (for GV-MDR series only)

7

• 2-axis mechanism (GV-MFD series); 3-axis mechanism (GV-MDR series)

Camera Type

GV-MFD series

Pan

-45° ~ +45°

GV-MDR series -45° ~ +45°

Tilt

0° ~ 90°

0° ~ 90°

• Micro SD card slot (SD/SDHC) for local storage

Rotate

N/A

0° ~ 360°

• Recording assigned by GV-Edge Recording Manager (Windows &

Mac)

• USB slot for GV-WiFi adapter or USB hard drive (for GV-MFD1501

Series / 2401 series / 2501 series / 3401 series / 5301 series)

• DC / PoE (IEEE 802.3af, for GV-MFD Series)

• PoE (IEEE 802.3af, for GV-MDR Series)

• Two-way audio (for GV-MFD1501 Series / 2401 series / 2501 series /

3401 series / 5301 series)

• 3D noise reduction (for GV-MFD1501 Series / 2501 Series, GV-

MDR1500 Series)

• 2D noise reduction (except for GV-MFD1501 Series / 2501 Series,

GV-MDR1500 Series)

• IP address filtering

• Support for iPhone, iPad, Android and 3GPP

• 31 languages on Web interface

• ONVIF (Profile S) conformant

8

1.3 Overview

1.3.1 GV-MFD120 / 130 / 320

1 2 3 4

1


5

No. Name

2 Lens

3 Tilt Screw

4 Microphone

5 Pan Screw

6

7

Figure 1-1

Description

Resets the camera to factory default. For details, see 1.6 Loading Factory Default.

Receives image inputs.

Loosens the screw to adjust tilt angle.

Loosens the screw to pan.

9

No. Name Description

6 LED LED Indicators below.

7 Memory Card Slot Inserts a micro SD card (SD/SDHC, version 2.0 only, Class 10) to store recording data.

LED Name

1. Link

2. ACT

3. PWR

4. SW RDY (Status)

Description

Turns on when the network is connected.

Turns on when data are being transmitted.

Turns on when power is on.

Turns on when the system is ready.

10

1


1.3.2 GV-MFD1501 Series / 2401 Series / 2501 Series /

3401 Series / 5301 Series

2

1

3

4

5

6

7

Figure 1-2

No. Name

1 Microphone

2

3

4

6

7

Pan Screw

Lens

Tilt Screw

Description

Loosens the screw to pan.




DC 5V Power Port Connects to power.

LAN / PoE Connects to a 10/100 Ethernet or PoE.

Inserts a micro SD card (SD/SDHC,

8

9

9 USB and Audio Out recording data.

Connects to a GV-WiFi Adapter/USB hard drive and a speaker through the supplied Y cable.

11

1

2

3

4

Figure 1-3

LED Name

1. Link

2. ACT

3. Status

4. Power

Description

Turns on (green) when the network is connected.

Turns on (orange) when data are being transmitted.

Turns on (red) when the system is ready.

Turns on (green) when power is on.

Note: For details on limitations and requirements of the USB port, refer to Note for USB Storage and WiFi Adapter at the beginning of this manual.

12

1


1.3.3 GV-MDR

1

2

5

3

4

6

7

No. Name

1 Silica gel bag

3

4

5

6

7

Lens

Rotation Disc

Pan Disc

Tilt Screw

Microphone

8

9

10

11

Figure 1-4

Description

Absorbs the moisture inside the camera.

Prevents water or moisture from entering the camera.


Rotates the camera lens.

Pans the camera lens.

Loosens to tilt the camera.

Provides one-way audio.

13

No. Name

9

Power and status

LED

10 LAN LED

Description


Turns red when the power is on. Flashes orange light twice when the system is ready.

Turns on when the network is connected.

Inserts a micro SD card (SD/SDHC, version 2.0 only, Class 10) to store recording data.

IMPORTANT: In case of damage and possible condensation inside the camera housing, be sure not to touch or remove the conceal paper.

LAN Connector

Two types of LAN connector are available for GV-MDR1500 series / 3400 series / 5300 series. Select an option based on your installation environment.

1.

Waterproof M12 4-Pin Female Connector

The M12 connector is used for motor vehicles.

Ø14.7 mm (0.58'')

14

1


2.

Small Waterproof Connector

For this connector type, see 1.4.2 GV-MDR to install the supplied cable connector.

42.8 mm (1.69")

15

1.4 Installation

To install a Mini Fixed Dome, make sure the installing site is shielded from rain and moisture.

1.4.1 GV-MFD Series

1. Unscrew the housing cover using the supplied torx wrench.

2. Put the camera on the desired location and make 2 marks on the ceiling for screw anchors. If you want to run the cables inside the ceiling, make a round mark with a diameter of 2.5 cm.

3. Drill the marks and insert the screw anchors.

4. Secure the Mini Fixed Dome to the ceiling with the self-tapping screws.

5. Connect the camera to network and power. For details, see 1.5

Connecting the Camera.

6. Access the live view. For details, see 2.1 Accessing the Live View,

GV-IPCam Firmware Manual.

7. Adjust the angles based on the live view.

Pan Adjustment Tilt Adjustment

16

Figure 1-5

Figure 1-6

1


8. Adjust image clarity using the GV-IP Device Utility program. For details, see 2.3 Adjusting Image Clarity, GV-IPCam Firmware Manual.

9. Insert a Micro SD card (SD/SDHC, version 2.0 only, Class 10) into the memory card slot (No. 7, Figure 1-1).

10. Secure the housing cover using the supplied torx wrench.

11. Optionally conceal the cable opening with the supplied cable stopper.

Cable stopper

Figure 1-7

17

1.4.2 GV-MDR Series

1. Paste the installation sticker on the desired location. The arrow should point toward the direction that the camera faces.

2. Drill one hole on each of the two curves for screw anchors. Drill the circle (30 mm in diameter) if you want to run the cable into the ceiling.

30 mm

Drill a hole on each

Figure 1-8

3. Insert the screw anchors.

4. Unscrew the housing cover using the supplied torx wrench.

5. Secure the camera body to the ceiling with the self-tapping screws.

18

Figure 1-9

1


6. Install the cable connector to waterproof the cable. You should have 5 parts:

1 2 3 4

5

Figure 1-10

A. Prepare an Ethernet cable with the RJ-45 connector on one end only.

Figure 1-11

B. Connect the Ethernet cable to the camera cable.

C. Paste the sticker to the camera cable and slide in all the components as shown below.

Figure 1-12

19

D. Move all the components toward the RJ-45 connector, fit item 4 to item 2, secure item 3 to the camera cable and finally secure item 5 to item 2 tightly.

Figure 1-13

IMPORTANT: Item 5 must be secured tightly to waterproof the cable.



8. Adjust the angles based on the live view.

Pan Adjustment

Figure 1-14

20

Tilt Adjustment

Figure 1-15

Rotational Adjustment

1


Figure 1-16

9. Adjust image clarity using the GV-IP Device Utility program. For details, see 2.2 Adjusting Image Clarity, GV-IPCam Firmware Manual.

10. Insert a Micro SD card (SD/SDHC, version 2.0 only, Class 10) into the memory card slot (No. 11, Figure 1-2).

11. Replace the silica gel bag.

IMPORTANT: The silica gel bag loses it effectiveness when the dry camera is opened. To prevent the lens from fogging up, replace the silica gel bag every time you open the camera, and conceal the gel bag in camera within 2 minutes of exposing to open air.

12. Secure the housing cover using the supplied torx wrench.

21

22

Figure 1-17

Cable stopper

1


1.5 Connecting the Camera

Refer to the wire definition and illustrations below to connect the power and network.

1.5.1 Wire Definition

GV-MFD120 / 130 / 320

The data cable provides connections for power and network access. The wires are illustrated and defined below:

No. Wire Color

1 Yellow

2 Orange

3 Gray

Figure 1-18

Definition

DC 12V+

GND

GV-MDR Series

Power and network connectivity is provided through a PoE cable.

Wire Color Definition

23

1.5.2 Power and Network Connection

Use one of the following methods to power on and connect your camera to network:

•

Wired connection with PoE: Use a Power over Ethernet (PoE) adapter to connect the camera to the network, and the power will be provided at the same time.

•

Wired connection with network cable (GV-MFD Series only):

Connect the camera with a standard network cable and use the power adapter to supply power. For details, see Powering On for GV-MFD

Series below to assemble the terminal block with power adapter.

•

Wireless connection (GV-MFD1501 Series / 2401 Series / 2501

Series / 3401 Series / 5301 Series only): Connect the camera with a

GV-WiFi Adapter (optional accessory) and use the power adapter to supply power.

Powering On the GV-MFD120 / 130 / 320

1. Insert the orange wire of the camera to the left pin (-) and the yellow wire to the right pin (+) of the terminal block.

Figure 1-19

2. Connect the power adapter to the terminal block.

Terminal Block

Figure 1-20

DC 12V Power Adaptor

24

1


3. Connect the camera to network using a network cable.

1.5.3 Vehicle Installation

To install the Mini Fixed Rugged Dome on a vehicle, clip the ferrite core to the camera cable. In accordance to EN 50155, the ferrite core is used for reduction of the cable-based and radiated interferences, ensuring stable image quality. The ferrite core must be attached as close as possible to the camera with the maximum distance of 15 cm.

Max. 15 cm

Ferrite Core

Figure 1-21

25

1.6 Loading Factory Default

1. Keep the power and network cables (or PoE) connected to the camera.

2. Press and hold the default button.

Figure 1-22

(GV-MFD120 / 130 / 320)

Default button

Status LED

Default button

Figure 1-23

(GV-MFD1501 Series / 2401 Series / 2501 Series / 3401 Series /

5301 Series)

take about 8 seconds. completed and the camera reboots automatically.

26

2

Mini Fixed Dome (Part II)

Chapter 2 Mini Fixed Dome (Part II)

The GV-MFD2700 Series / 4700 Series offers an indoor, fixed, mini-sized network camera with 3-axis mechanism for easy and flexible installation.

GV-MFD2700 Series / 4700 Series can support H.265 video codec to achieve better compression ratio while maintaining high picture quality at reduced network bandwidths. The camera can process scenes with contrasting intensity of lights and produce clear image using the builtin

WDR Pro. The camera is equipped with a Super Low Lux CMOS image sensor which allows the camera to provide a color live view in near darkness.

Model No.

GV-MFD2700-0F

GV-MFD2700-2F

Specifications


F/2.0, 1/2.7” M12

Mount


F/1.8, 1/2.7” M12

Mount

Description

2 MP, H.265,

Super Low

Lux, WDR Pro

Fixed

Lens

GV-MFD4700-0F


F/2.0, 1/2.7” M12

Mount 4 MP, H.265,

Super Low

Lux, WDR Pro

GV-MFD4700-2F


F/1.8, 1/2.7” M12

Mount

27


y H.265 Mini Fixed IP Dome y Screw

2 y Screw Anchor x 2 y Audio and I/O extended cable y GV-IPCAM Software DVD

Note: Power adapters can be purchased upon request.

28

2


2.2 Features

• Image


GV-MFD2700 Series 1/2.8’’ progressive scan low lux CMOS

GV-MFD 4700 Series

1/3” progressive scan super low lux

CMOS


GV-MFD 2700 Series

Up to 30 fps at 1920 x 1080

GV-MFD 4700 Series

Up to 25 fps at 2560 x 1440

Up to 30 fps at 2048 x 1520

• Dual streams from H.265, H.264 or MJPEG

• Min. illumination at 0.004 lux (GV-MFD2700 Series)

• Min. illumination at 0.002 lux (GV-MFD4700 Series)

• 3-axis mechanism (pan / tilt / rotate)

• One sensor input and alarm output

• Built-in micro SD card slot (SD/SDHC/SDXC/UHS-I) for local storage

• Day and night function (with removable IR-cut filter)

• DV 12V / PoE (IEEE 802.3af)

• Wide Dynamic Range Pro (WDR Pro)

• 3D noise reduction

• Defog

29



Mac)




30

2


2.3 Overview

1

3 d c

2 b

8

4 a

7

5

6

Figure 2-1

No. Name

1. Lens

2. Pan Screw

Description


Loosens the screw to adjust pan angle.

3. Tilt Screw

4.

Default

Button

5.

6.

7.

8. a

DC 12V Port

LAN / PoE

Audio and

I/O Terminal

Block

Memory

Card Slot

Status



Connects to power.

Connects to a 10/100 Ethernet or PoE.

Connects the camera to a microphone or a speaker and to one input and one output devices using audio and I/O extended cable. For details, see 2.5

Connecting the Camera.

Inserts a micro SD card (SD/SDHC/SDXC/UHSI,

Class 10) to store recording data. Note UHSII card type is not supported.

Turns on (green) when the system is ready.

31

b c d

Power

Link

ACT




32

2



The Mini Fixed Dome can be installed on the wall or the ceiling. Before installing the camera, make sure the installing site is shielded from rain and moisture.

1. Open the housing cover by unscrewing the three screws.

Figure 2-2

2. Place the camera where you want to install it, and make 2 marks on the ceiling or the wall for screw anchors. If you want to run the cables inside the ceiling or the wall, make a round mark with a diameter of

2.5 cm.

Figure 2-3

33


4. Thread the power and / or network cable(s) through the oval-shaped hole or the cable opening on the side.

Figure 2-4

5. Connect the camera to network, power, a microphone or a speaker, and one input and one output devices. For details, see 2.5


6. Optionally insert a memory card.

7. Secure the camera to the ceiling or the wall with the supplied screws.




34

2


10. Loosen the tile screw, pan screw or rotational screw. Adjust the angles based on the live view as needed, and tighten the screws again.

Figure 2-5

11. Place the housing cover back and turn to secure it.

35


2.5.1 Wire Definition

The supplied audio and I/O extended cable allows you to connect one sensor input and alarm output, and one microphone and speaker.

NO. Wire Color

1. Red

2. Yellow

3. Black

4.

5.

Red RCA

Green RCA

Definition

Ground

Audio in

Audio out

Figure 2-6

For details on how to enable an installed I/O device, see 4.2 I/O Settings,

GV-IPCam Firmware Manual.

36

2


2.5.2 Voltage Load Expansion (Optional)

The camera can only drive a maximum load of 200mA 5V DC. To expand the maximum voltage load to 10A 250V AC, 10A 125V AC or 5A 100V DC, connect the camera to a GV-Relay V2 module (optional product). Refer to the figure and table below.

GV-Relay V2

DO1

Figure 2-7

Mini Fixed Dome

Digital Out (Yellow)

37


Keep the power connected to the camera. Press and hold the default button for about 8 seconds. Release the button when the status LED blinks. For details, see 1.6 Lading Factory Default.

Figure 2-7

38

3

Target Mini Fixed Dome

Chapter 3 Target Mini Fixed Dome

The Target Mini Fixed Dome (GV-EFD) is an indoor, fixed, mini-sized network camera equipped with an automatic IR-cut filter and IR LEDs for day and night surveillance. Adjustable in 2 axis (pan and tilt), it offers an entry-level surveillance solution with all the essential features and excellent image quality.

Model No.

GV-EFD1100-0F

GV-EFD2100-0F

Specifications


F/2.0, 1/2.7” M12

Mount

Description

1.3 MP / 2 MP,

H.264, Low

Lux

GV-EFD4700-0F


F/2.0, 1/2.7” M12

Mount

4 MP, H.265,

Super Low

Lux, WDR Pro

Fixed

Lens

GV-EFD1100-2F

GV-EFD2100-2F


F/1.8, 1/2.7” M12

Mount

1.3 MP / 2 MP,

H.264, Low

Lux

GV-EFD4700-2F


F/1.8, 1/2.7” M12

Mount

4 MP, H.265,

Super Low

Lux, WDR Pro

39


• Target Mini Fixed Dome (for GV-EFD1100 Series / 2100 Series)

• H.265 Mini Fixed Dome (for GV-EFD4700 Series)

• Screw x 2


• GV-IPCAM Software DVD

• Warranty Card


40

3


3.2 Features

• Image

Camera Model

GV-EFD1100 Series

GV-EFD2100 Series

GV-EFD4700 Series

Image Sensor


1/2.8’’ progressive scan low lux CMOS

1/3” progressive scan super low lux

CMOS

Camera Model

GV-EFD1100 Series

Frame Rate

Up to 30 fps at 1280 x 1024

GV-EFD2100 Series Up to 30 fps at 1920 x 1080

GV-EFD4700 Series

Up to 25 fps at 2560 x 1440

Up to 30 fps at 2048 x 1520


Dual streams from H.265, H.264 or MJPEG (for GV-EFD4700 Series)

• Min. illumination at 0.02 lux (for GV-EFD4700 Series)


• 2-axis mechanism (pan / tilt)



Wide Dynamic Range Pro (WDR Pro) (for GV-EFD4700 Series)

• 3D noise reduction (for GV-EFD4700 Series)

• Smart streaming (for GV-EFD4700 Series)

• Defog

41


• NAS Recording (for GV-EFD1100 / 2100 Series)


Mac)




Not e

: For optimal performance and compatibility, it is highly recommended to use GV-EFD1100 / 2100 Series with a GV-NAS

System.

42

3


3.3 Overview

1

3

4 a b

5

6

2

No. Name

1

2

3

Lens

Pan Screw

Tilt Screw

Figure 3-1

Description




7

5

6

7 a b c d

Default

Button


DC 12V Port Connects to power.

LAN / PoE

Status

Power

Link

ACT






c d

43

Note: The TV-out function can only be used during installation to adjust the focus of the camera. To use the TV out function, connect the supplied black BNC connector to a monitor and select your signal format

(NTSC or PAL) at the

TV Out field on the Web interface. The default signal format is NTSC. For details, see 4.1.1 Video Settings, GV-IPCam

Firmware Manual.

44

3



The Target Mini Fixed Dome can be installed on the wall or the ceiling.

Before installing the camera, make sure the installing site is shielded from rain and moisture.

12. Open the housing cover by turning.

Figure 3-2

13. Place the camera where you want to install it, and make 2 marks on the ceiling or the wall for screw anchors. If you want to run the cables inside the ceiling or the wall, make a round mark with a diameter of

2.5 cm.

Figure 3-3

45


15. Thread the power and / or network cable(s) through the oval-shaped hole or the cable opening on the side.

Figure 3-4



17. Secure the camera to the ceiling or the wall with the supplied screws.



Note: The TV-out function can only be used during installation to adjust the focus of the camera. To use the TV out function, connect the supplied black BNC connector to a monitor and select your signal format

(NTSC or PAL) at the TV Out field on the Web interface. The default signal format is NTSC. For details, see 4.1.1 Video Settings, GV-IPCam

Firmware Manual.


46

3


20. Loosen the tile screw, pan screw or rotational screw. Adjust the angles based on the live view as needed, and tighten the screws again.

Figure 3-5

21. Place the housing cover back and turn to secure it.

47


Figure 3-6

1. Connect power using one of the following methods:

•

Plug the power adapter to the 12V terminal block. The power adapter is an optional device. For detail, see Options in the manual.

•

Use the Power over Ethernet (PoE) function and the power will be provided over the network cable.

The power and status LEDs shall turn on (green).

2. Use a standard network cable to connect the camera to your network.

3. You are ready to access the live view, adjust the image clarity and configure the basics. See Getting Started, Chapter 2, GV-IPCam

Firmware Manual.

48

3



Keep the power connected to the camera. Press and hold the default button for about 8 seconds. Release the button when the status LED blinks. For details, see 1.6 Lading Factory Default.

Figure 3-7

Figure 3-8

49

Chapter 4 Target Mini Fixed

Rugged Dome

The Target Mini Fixed Rugged Dome (GV-EDR) is an outdoor, fixed, minisized network camera equipped with an automatic IR-cut filter and IR LEDs for day and night surveillance. Adhering to IK10 and IP67 standards, it offers an entry-level outdoor surveillance solution with all the essential features and excellent image quality.

For GV-EDR4700, with its super low lux CMOS image sensor and WDR

Pro, it is capable of not only providing a color live view in near darkness but also under contrasting light intensities. GV-EDR4700 can support H.265 video codec to achieve better compression ratio while maintaining high quality pictures at reduced network bandwidths.

Model No.

GV-EDR1100-0F

GV-EDR2100-0F

GV-EDR4700-0F

GV-EDR1100-2F

GV-EDR2100-2F

GV-EDR4700-2F

Fixed

Lens

Specifications


F/2.0, 1/2.7” M12

Mount


F/1.8, 1/2.7” M12

Mount

Description

1.3 MP / 2 MP,

H.264, Low

Lux,

4 MP, H.265,

Super Low Lux

50


• Target Mini Fixed Rugged Dome

• Screw x 2


• Focus Adjustment Ring

4

Target Mini Fixed Rugged Dome

• Waterproof Rubber Sets (for RJ-45 Cat.5 and 12V DC / for RJ-45

Cat.6)

Cat.5

(Ø 5 mm)

Cat.6

(Ø 6 mm)

• Silica Gel Bag x 2

• Adhesive Tape for Silica Gel Bag x 2

• Ruler

• Screw for Conduit Converter x 2

• GV-IPCAM Software DVD


51

Note: You can choose to run the wires through a conduit pipe. After you have threaded all the wires, install the supplied conduit converter with a

PG21 conduit connector and a self-prepared conduit pipe (of 1/2’’, 3/4’’ or 1’’) to the camera. Do not use a 1/2’’ pipe if you use the power adapter for power supply because the adapter cannot be threaded through. A plastic PG21 conduit connector for 1/2” pipe can be purchased upon request.

Plastic PG21 conduit connector

Conduit pipe

Conduit converter

52

4


4.2 Features

• Image


GV-EDR1100 Series


GV-EDR2100 Series

1/2.8’’ progressive scan low lux CMOS

GV-EDR4700 Series 1/3” progressive scan super low lux

CMOS


• Dual streams from H.265, H.264 or MJPEG (for GV-EDR4700 Series)

Camera Model

GV-EDR1100 Series

GV-EDR2100 Series

GV-EDR4700 Series

Frame Rate

30 fps at 1280 x 1024

30 fps at 1920 x 1080

25 fps at 2560 x 1440


• 2-axis mechanism (pan / tilt)



• Wide Dynamic Range Pro (WDR Pro) (for GV-EDR4700 Series)

• 3D noise reduction (for GV-EDR4700 Series)

• Smart streaming (for GV-EDR4700 Series)

• Defog

• Ingress protection (IP67)

• Vandal resistance (IK10 for metal casing)

53


• NAS Recording (excluding GV-EDR4700 Series)


Mac)




Not e

: For optimal performance and compatibility, it is highly recommended to use a GV-NAS System.

54

4


4.3 Overview

1 a b

2

3

4

5 6

Figure 4-1

a b c d

5

6

Description No. Name

1

2

3

4

Lens

Tilt Screw

Pan Screw

Default

Button





DC 12V Port Connects to power.

LAN / PoE Connects to a 10/100 Ethernet or PoE.

Status

Power

Link

ACT





c d

55


The Target Mini Fixed Rugged Dome can be installed on the wall or ceiling.

You must use the supplied waterproof rubber set to waterproof the cable.

1. Paste the installation sticker where you want to install, and drill two holes that are at a diagonal. To run the cables inside the wall or ceiling, drill a larger opening as shown below.

Figure 4-2

2. Insert the supplied screw anchors into the two drilled holes.

3. Open the camera’s housing cover using the supplied torx wrench.

56

Figure 4-3

4


4. Unscrew the three screws as indicated below. A back plate can be separated from the bottom.

Figure 4-4

5. Use the 2 supplied screws to secure the back plate onto the ceiling or the wall where the screw anchors were inserted.

Figure 4-5

6. Prepare an Ethernet cable with the RJ-45 connector on one end only.

57

7. Remove the waterproof cap from the cable opening and thread the power and / or network cable(s) through the opening.

Figure 4-6

8. Install the supplied waterproof rubber set onto the cable(s). The rubber set has two parts. According to the below situation, replace

Part 1 if necessary. y

For users of PoE with a Cat.5 Ethernet cable, stay with Part 1a on the camera body. y

For users of PoE with a Cat.6 Ethernet cable, change Part 1a to the supplied Waterproof rubber set (1b). y

For users of DC 12V, change Part 1a to the supplied Waterproof rubber set (1c).

For Cat.5 Ethernet cable (PoE)

For Cat.6 Ethernet cable (PoE)

For adapter wire

For Ethernet cable

1a

1b

Figure 4-7

1c

2

58

4


A. Slide the waterproof rubber set, and the waterproof cap you previously removed through the cable(s) as shown below.

1 2

Figure 4-8

B. Connect the supplied RJ-45 connector to the Ethernet cable.

C. If you are using a power adapter, insert the striped wire to the left pin (+) and the other wire to the right pin (-).

Figure 4-9

D. Fit item 1 to item 2, and insert them in the cable opening. Use the supplied ruler to make sure the length of the cable(s) from the bottom of the opening to the end of the cable is under

10 cm.

Figure 4-10

59

E. Cap the cable opening with the waterproof cap. Use the supplied concave hexagon wrench to tighten.

Figure 4-11

9. Thread the cable(s) under the black cable holder. You can loosen the screw on the cable holder if needed.

Figure 4-12



11. Secure the camera to the back plate by tightening the three screws as shown in Step 4.

60

4





14. Loosen the tile screw and pan screw, adjust the angles based on the live view as needed, and tighten the screws again.

15. Attach the silica gel bag to the place indicated below, and secure the housing cover using the torx wrench.

61

IMPORTANT:

1. The gel bag loses its effectiveness when the dry camera is opened. To prevent the lens from fogging up, replace the silica gel bag every time you open the camera and conceal the silica gel bag within 2 minutes of exposing to open air.

2. Make sure the housing cover is properly secured to prevent water from entering and damaging the inner housing.

62

4



1

2

Figure 4-15


•

Plug the power adapter to the 12V terminal block. The power adapter is an optional device. For detail, see Options in the manual.

•

Use the Power over Ethernet (PoE) function and the power will be provided over the network cable.

The power and status LEDs shall turn on (green).


3. You are ready to access the live view, adjust the image clarity and configure the basics. See Getting Started, Chapter 2, GV-IPCam

Firmware Manual.

63


1. Keep the power and network cables (or PoE) connected to the camera.

2. Press and hold the default button for about 8 seconds.

Figure 4-16

64

Figure 4-17 completed and the camera reboots automatically.

5

Cube Camera

Chapter 5 Cube Camera

The Cube Camera is a light weighted network camera designed for indoor usage. Its simple design allows for fast and easy installation and fixed-spot surveillance once installed. Four models are available:

Model No.

Specification Description

GV-CB120

GV-CB220

Fixed

Lens

Fixed Iris, f: 3.35 mm, F/2.4, 1/3”

M12 mm lens mount

1.3 MP, H.264, Cube

Camera

2 MP, H.264, Cube

Camera

65


• Screw

3


DVD

• GV-Software DVD


66

5.2 Features

• 1/2.5’’ progressive scan CMOS


• Frame rate


GV-CB120

GV-CB220

30 fps at 1280 x 1024

30 fps at 1920 x 1080



• Defog

• Two-way audio



• Motion detection

• Tampering alarm

• Text overlay

• Privacy mask


• Megapixel lens




5

Cube Camera

67

5.3 Overview

1 2 3 4 5 6 7 8 9

Figure 5-1

Description No. Name

1 Microphone

2 Speaker

3 LAN

6 Stand screw

7 Default Button

8 Power port

9 Memory Card Slot

Connects to a 10/100 Ethernet.

Turns red when the system powers on.

Turns orange when the system is ready.

Turns green when the camera is connected to the Internet through wires.

Connects to the Supporting Rack.


Connects to the power adapter.

Inserts a micro SD card (SD/SDHC, version

2.0 only, Class 10) to store recording data.

68

5

Cube Camera


Follow the steps below to install, connect to and adjust your Cube Camera and Wireless Cube Camera.

1. Put the supporting rack on the desired location and make marks for screw anchors.

Figure 5-2


3. Secure the supporting rack onto the wall using the supplied screws.

4. Screw the camera onto the supporting rack and fasten the indicated screw.

Figure 5-3

69

5. Connect the network and power cables to the camera. See 5.5


6. Access the live view. See 2.1 Accessing the Live View, GV-IPCam

Firmware Manual.

7. Adjust the angle of the camera based on live view and fasten the indicated screw.

Figure 5-4

70


5

Cube Camera

1

2

Figure 5-5


2. Power on using the power adapter.

3. The status LED of the camera will be orange.

IMPORTANT: Be sure to use the GeoVision power adapter to power up the camera. To use your own power cable, make sure you look up the power source value indicated at the camera’s back panel.

71


1. Keep the power and network cables connected to the camera.

2. Use a pin to press and hold the default button on the panel.

Default button

Status LED

Figure 5-6

take about 8 seconds. settings is completed and the camera is ready for use.

72

6

Advanced Cube Camera

Chapter 6 Advanced Cube

Camera

The Advanced Cube Camera integrates the passive infrared (PIR) sensor and the alarm LED to illuminate the scene automatically when the motion is detected. It also offers wireless connection to the network for flexible installation. It is small, light, and easy-to-use for indoor security. We provide four models:

Model No.

Specification Description

GV-CA120

1.3 MP, H.264,

Cube Camera

GV-CA220

GV-CAW120

GV-CAW220

Fixed

Lens

Fixed Iris, f: 3.35 mm, F/2.4, 1/3” M12 mm lens mount

2 MP, H.264, Cube

Camera

1.3 MP, H.264,

Wireless Cube

Camera

2 MP, H.264,

Wireless Cube

Camera

73


• Advanced Cube Camera • Supporting Rack

• Screw x 3 • Screw Anchor x 3

• GV-IPCAM H.264 Software

DVD

• GV-Software DVD

• Power Adapter

• Warranty Card


74

6


6.2 Features

• 1/2.5’’ progressive scan CMOS


• Frame rate

Camera Model

GV-CA120 / CAW120

GV-CA220 / CAW220

Frame Rate

30 fps at 1280 x 1024

30 fps at 1920 x 1080


• Passive infrared (PIR) sensor for detecting movement and activating the white illumination LED

• DC 5V / PoE (IEEE 802.3af, for GV-CA120 / 220 only)



• Defog

• Wireless connectivity: WiFi 802.11b/g/n (for GV-CAW120 / 220 only)

• NAS recording

• Recording assigned by GV-Edge Recording Manager (Windows & Mac)

• Two-way audio


• Motion detection

• Tampering alarm

• Text overlay

• Privacy mask


• Megapixel lens

• Smart device access



75

6.3 Overview

13

1 2 3 4 5 6 7 8 9 10 11

No. Name

1 Speaker

2 PIR sensor

3 Microphone

12

Figure 6-1

Description

Plays sounds for tampering and motion alarm, and listens to the audio around the camera. To set up alarm sound, see 4.3.9

Speaker, GV-IPCam Firmware Manual.

Passive infrared sensor.

4

White Illumination

LED

7 LAN / PoE

When the PIR sensor detects the movement, the white illumination LED lights up in a low light scene. To set up the

LED, see 4.1.1 Video Settings, GV-IPCam

Firmware Manual.

Reflects monitoring status of the camera.

See the below table.

Reflects live view status of the camera.

See the below table.


76

6


No. Name

8 Stand screw

9 Power port

12 Memory Card Slot

13 Default

Description

Connects to the Supporting Rack.

Connects to the power adapter.

Reflects system status of the camera. See the below table.

Reflects LAN status of the camera. See the below table.

Inserts a micro SD card (SD/SDHC, version 2.0 only, Class 10) to store recording data.


IMPORTANT: The White Illumination LED can reach high temperatures.

Be sure not to touch the LED with bare hand.

LED

Live View

Monitoring

Ready

LAN

Status Description

•

Turns on orange light when you see the live view.

•

Turns on red light when you start monitoring.

•

Turns on green light when the

• system is ready.

Flashes green light when you

• load default value.

Turns on green light when you

• connect the LAN Network.

Turns on blue light when you connect the Wi-Fi Network (for GV-

CAW120 / 220 only).

77


Follow the steps below to install, connect to and adjust your Advanced

Cube Camera and Wireless Advanced Cube Camera.

1. Put the supporting rack on the desired location and make marks for screw anchors.

Figure 6-2


3. Secure the supporting rack onto the wall using the supplied screws.

4. Screw the camera onto the supporting rack and fasten the indicated screw.

78

Figure 6-3

6


5. Connect the network and power cables to the camera. See 6.5

Connecting the Camera.

6. Access the live view. See 2.1 Accessing the Live View, GV-IPCam

Firmware Manual.

7. Adjust the angle of the camera based on live view and fasten the indicated screw.

Figure 6-4

8. For GV-CAW120/220, to connect to the Internet through wireless service, follow the steps in 2.1.3 Configuring the Wireless Connection,


79


1

2

Figure 6-5



• plugging the power adapter to the power port.

• using the Power over Ethernet (PoE) function and the power will be provided over the network cable.

3. When the ready LED of the camera shines green, the camera is ready for use.

Note: PoE function is only supported for GV-CA120 and GV-CA220.

80

6



1. Keep the power and network cables connected to the camera.

2. Use a pin to press and hold the default button on the panel.

Default button

Figure 6-6

Status LED take about 8 seconds. settings is completed and the camera is ready for use.

81

GeoVision Cube Camera, Mini Fixed Dome, Mini Fixed Rugged Dome, EFD 1100, EFD 2100, EFD 4700 Target Mini Fixed Dome, EDR 1100, EDR 2100, EDR 4700 Target Mini Fixed Rugged Dome Hardware Manual

Assistant Bot

GV-IPCam

Hardware Manual

Cube Camera

Mini Fixed Dome

Mini Fixed Rugged Dome

Target Mini Fixed Dome

Target Mini Fixed Rugged Dome

Caution

Safety Notice

Contents

Options

Note for USB Storage and WiFi

Adapter

Note for Installing Camera Outdoor

Chapter 1 Mini Fixed Dome (Part I)

& Mini Fixed Rugged Dome

Chapter 2 Mini Fixed Dome (Part II)

Chapter 3 Target Mini Fixed Dome

Chapter 4 Target Mini Fixed

Rugged Dome

Chapter 5 Cube Camera

Chapter 6 Advanced Cube

Camera

Key Features

Frequently Answers and Questions

What is the difference between the Target Mini Fixed Dome and the Target Mini Fixed Rugged Dome?

What is the minimum illumination for the Target Mini Fixed Dome?

What video codecs are supported by the Target Mini Fixed Dome?

What is the frame rate of the Target Mini Fixed Dome?

How do I connect the Target Mini Fixed Dome to a network?

Related manuals

Table of contents

GeoVision Cube Camera, Mini Fixed Dome, Mini Fixed Rugged Dome, EFD 1100, EFD 2100, EFD 4700 Target Mini Fixed Dome, EDR 1100, EDR 2100, EDR 4700 Target Mini Fixed Rugged Dome Hardware Manual

Assistant Bot

GV-IPCam

Hardware Manual

Cube Camera

Mini Fixed Dome

Mini Fixed Rugged Dome

Target Mini Fixed Dome

Target Mini Fixed Rugged Dome

Caution

Safety Notice

Contents

Options

Note for USB Storage and WiFi

Adapter

Note for Installing Camera Outdoor

Chapter 1 Mini Fixed Dome (Part I)

& Mini Fixed Rugged Dome

Chapter 2 Mini Fixed Dome (Part II)

Chapter 3 Target Mini Fixed Dome

Chapter 4 Target Mini Fixed

Rugged Dome

Chapter 5 Cube Camera

Chapter 6 Advanced Cube

Camera

Key Features

Frequently Answers and Questions

What is the difference between the Target Mini Fixed Dome and the Target Mini Fixed Rugged Dome?

What is the minimum illumination for the Target Mini Fixed Dome?

What video codecs are supported by the Target Mini Fixed Dome?

What is the frame rate of the Target Mini Fixed Dome?

How do I connect the Target Mini Fixed Dome to a network?

Related manuals

Geovision

GV-EFD 1100-0F

Geovision

GV-MFD 1501

Geovision

IP Camera

Geovision

BX5300 GV-BX5300-6V

Geovision

84-MD120-100U

Geovision

GV-EFD2100 0F

Geovision

GV-EFD2100

Geovision

84-CA12000-100U

Geovision

GV-EDR1100

Geovision

84-MDR2200-0100

Table of contents