Sony | MZ-NH1 | User's Manual | Sony MZ-NH1 User's Manual

MZ-NH1
SERVICE MANUAL
US Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
Tourist Model
Ver 1.1 2004.09
US and foreign patents licensed from Dolby
Laboratories.
• SonicStage and SonicStage logo are trademarks or registered trademarks of Sony Corporation.
• MD Simple Burner, OpenMG, “MagicGate”, “MagicGate Memory Stick”, “Memory Stick”, HiMD, Net MD, ATRAC, ATRAC3, ATRAC3plus and their logos are trademarks of Sony Corporation.
• Microsoft, Windows, Windows NT and Windows Media are trademarks or registered trademarks
of Microsoft Corporation in the United States and/or other countries.
• IBM and PC/AT are registered trademarks of International Business Machines Corporation.
• Macintosh is a trademark of Apple Computer, Inc. in the United States and/or other countries.
• Pentium is a trademark or registered trademark of Intel Corporation.
• All other trademarks and registered trademarks are trademarks or registered trademarks of their
respective holders.
Model Name Using Similar Mechanism
NEW
MD Mechanism Type
MT-MZNH1-181
Optical Pick-up Name
ABX-U
SPECIFICATIONS
MD:
ATRAC
ATRAC3 — LP2/LP4
Audio playing system
MiniDisc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 790 nm
Emission duration: continuous
Laser output: less than 44.6 µW
(This output is the value measured at a distance
of 200 mm from the lens surface on the optical
pick-up block with 7 mm aperture.)
Recording and playback time (Refer
to page 94 for details)
Modulation system
Hi-MD:
1-7RLL (Run Length Limited)/PRML
(Partial Response Maximum Likelihood)
MD:
EFM (Eight to Fourteen Modulation)
Frequency response
Inputs1)
MIC: stereo mini-jack
(minimum input level 0.13 mV)
Line in:
stereo mini-jack for analog input
(minimum input level 49 mV)
optical (digital) mini-jack for optical
(digital) input
Revolutions
350 rpm to 3,600 rpm (CLV)
i/LINE OUT2): stereo mini-jack (dedicated
emote control jack)/194 mV (10 kΩ)
Error correction
Maximum output (DC)2)
Hi-MD:
LDC (Long Distance Code)/BIS (Burst
Indicator Subcode)
MD:
ACIRC (Advanced Cross Interleave Reed
Solomon Code)
Headphones:
5 mW + 5 mW (16 Ω)
44.1 kHz
Sampling rate converter
Input: 32 kHz/44.1 kHz/48 kHz
Coding
Hi-MD:
Linear PCM (44.1 kHz/16 bit) — PCM
ATRAC3plus (Adaptive TRansform
Acoustic Coding 3 plus)
9-879-075-02
2004I05-1
© 2004.09
Operating temperature
+5° C (+41° F) to +35° C (+95° F)
Battery life 4)
Hi-MD mode (When using a 1GB HiMD disc)
20 to 20,000 Hz ± 3 dB
When using HMD1G (1GB disc):
Maximum 34 hours in Hi-LP stereo
When using MDW-80 in Hi-MD mode:
Maximum 10 hours and 10 min. in Hi-LP
stereo
When using MDW-80 in MD mode:
Maximum 160 min. in monaural
Maximum 320 min. in LP4 stereo
Sampling frequency
The recorder:
Lithium-ion rechargeable battery
LIP-4WM, 3.7 V, 370 mAh, Li-ion
Battery charging stand:
AC power adaptor DC 6V
Outputs
(Unit: approx.hours)(JEITA3))
When
Linear Hi-SP
PCM
Hi-LP
Recording
continuously
6
8.5
9.5
Playing
continuously
10
15.5
18
Hi-MD mode (When using a 60/74/80minute standard disc)
(Unit: approx.hours)(JEITA)
When
Linear Hi-SP
PCM
Hi-LP
Recording
continuously
5
8
9
Playing
continuously
8
14.5
17.5
Power requirements
Sony AC Power Adaptor connected at the DC
IN 6V jack:
120 V AC, 60 Hz (Models for USA, Canada,
Mexico, and Taiwan)
240 V AC, 50 Hz (Model for Australia)
230 V AC, 50 Hz (Models for U.K. and
Hong Kong)
220 V AC, 50 Hz (Model for China)
100 - 240 V AC, 50/60 Hz (Other models)
– Continued on next page –
PORTABLE MINIDISC RECORDER
Sony Corporation
Personal Audio Company
Published by Sony Engineering Corporation
For other Service and User Manuals, go to www.ManualDepot.com
MZ-NH1
MD mode
(Unit: approx.hours)(JEITA)
When
SP
Stereo
LP2
Stereo
LP4
Stereo
Recording
continuously
8
10
10.5
Playing
continuously
14.5
17
18.5
On power sources
Use house current or rechargeable battery.
For use in your house: For the supplied battery
charging stand, use the AC power adaptor
supplied with this recorder. Do not use any
other AC power adaptor since it may cause the
recorder to malfunction.
Polarity of the plug
Dimensions
Approx. 81.7 × 76.1 × 14.8 mm (w/h/d)
(31/4 × 3 × 19/32 in.) (excluding projecting parts
and controls)
Mass
Approx. 97 g (3.4 oz) (the recorder only)
Approx. 107 g (3.8 oz) (including the
rechargeable battery)
1)The
LINE IN (OPT) jack is used to connect
either a digital (optical) cable or a line
(analog) cable.
2)The i/LINE OUT jack connects either
headphones/earphones or a line cable.
3) Measured in accordance with the JEITA
(Japan Electronics and Information
Technology Industries Association) standard.
4) When using a 100% fully charged lithium-ion
rechargeable battery
Design and specifications are subject to change
without notice.
Your dealer may not handle some of the above
listed accessories. Please ask the dealer for
detailed information about the accessories in
your country.
When using optional headphones, use only
headphones/earphones with stereo mini
plugs. You cannot use headphones/
earphones with micro plugs.
2
MZ-NH1
TABLE OF CONTENTS
1.
SERVICING NOTES ............................................... 4
2.
GENERAL ................................................................... 5
3.
DISASSEMBLY
3-1.
3-2.
3-3.
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
Disassembly Flow ...........................................................
Bottom Panel Sub Assy ...................................................
MAIN Board ....................................................................
Upper Panel Sub Assy .....................................................
Control Ornament Block .................................................
Mechanism Deck Assy (MT-MZNH1-181) ....................
Gear (SA), Gear (SB) ......................................................
Op Service Assy ..............................................................
DC SSM18D/C-NP Motor (Spindle) (M701),
DC SSM21A/C-NP Motor (Sled) (M702),
DC Motor Unit (Over Write Head Up/Down) (M703) ...
3-10. Holder Assy .....................................................................
7
7
8
8
9
9
10
10
11
11
4.
TEST MODE ............................................................... 12
5.
ELECTRICAL ADJUSTMENT ............................. 16
6.
DIAGRAMS
6-1.
6-2.
6-3.
6-4.
6-5.
6-6.
6-7.
6-8.
6-9.
6-10.
6-11.
6-12.
6-13.
6-14.
Block Diagram –MD SERVO Section – .........................
Block Diagram –AUDIO Section – .................................
Block Diagram –POWER SUPPLY Section – ................
Schematic Diagram –MAIN Section (1/9) – ...................
Schematic Diagram –MAIN Section (2/9) – ...................
Schematic Diagram –MAIN Section (3/9) – ...................
Schematic Diagram –MAIN Section (4/9) – ...................
Schematic Diagram –MAIN Section (5/9) – ...................
Schematic Diagram –MAIN Section (6/9) – ...................
Schematic Diagram –MAIN Section (7/9) – ...................
Schematic Diagram –MAIN Section (8/9) – ...................
Schematic Diagram –MAIN Section (9/9) – ...................
Printed Wiring Board –MAIN Section (1/2) – ................
Printed Wiring Board –MAIN Section (2/2) – ................
7.
EXPLODED VIEWS
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
21
22
23
25
26
27
28
29
30
31
32
33
34
35
7-1. PANEL SECTION ........................................................... 49
7-2. MAIN SECTION ............................................................ 50
7-3. MECHANISM DECK SECTION ................................... 51
8.
ELECTRICAL PARTS LIST ................................ 52
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
3
MZ-NH1
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
Installing
Providing the required system environment
System requirements
The following system environment is required in order to use the SonicStage/MD Simple
Burner software for the MD Walkman.
Computer
CPU: Pentium II 400 MHz or higher (Pentium III 450 MHz or higher
is recommended.)
Hard disk drive space: 200 MB or more (1.5 GB or more is
recommended) (The amount space will vary according to Windows
version and the number of music files stored on the hard disk.)
RAM: 64 MB or more (128 MB or more is recommended)
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
IBM PC/AT or Compatible
Others
CD drive (capable of digital playback by WDM)
Sound Board
USB port (supports USB (previously USB 1.1))
Operating
System
Factory installed:
Windows XP Media Center Edition 2004/Windows XP Media Center
Edition/Windows XP Professional/Windows XP Home Edition/
Windows 2000 Professional/Windows Millennium Edition/Windows
98 Second Edition
Display
High Color (16bit) or higher, 800 × 600 dots or better (1024 × 768 dots
or better is recommended)
Others
Internet access: for Web registration, EMD services and CDDB
Windows Media Player (version 7.0 or higher) installed for playing
WMA files
This software is not supported by the following environments:
OSs other than the indicated above
Personally constructed PCs or operating systems
An environment that is an upgrade of the original manufacturer-installed operating system
Multi-boot environment
Multi-monitor environment
Macintosh
Notes
We do not ensure trouble-free operation on all computers that satisfy the system requirements.
The NTFS format of Windows XP/Windows 2000 Professional can be used only with the standard
(factory) settings.
We do not ensure trouble-free operation of the system suspend, sleep, or hibernation function on all
computers.
For Windows 2000 Professional users, install Service Pack 3 or later version before using the
software.
OPERATION CHECK WHEN THE MAIN BOARD IS
REMOVED
In making an operation check with the MAIN Board removed from
the set, short the SL894 (OPEN/CLOSE) of the MAIN Board with
the solder before starting the operation check.
Note: Be sure to remove the solder used for shortcircuit after the repaire
completed.
– MAIN Board (Conductor Side) –
SL894
(OPEN/CLOSE)
4
MZ-NH1
SECTION 2
GENERAL
This section is extracted from
instruction manual.
Looking at controls
The recorder
1
9
0
qa
qs
qd
2
3
A x (stop) • CANCEL button
B Display window
C OPEN switch
D Battery compartment
E 5-way control key
qf
4
qg
5
6
7
8
qh
Operation
Function
Press NENT
play, enter
Press towards
FR
find the beginning
of the previous
track, rewind
Press towards
FF
find the beginning
of the next track,
fast forward
Press towards
VOL +1) or
VOL –.
volume
1)
1) There
F MENU button
G GROUP button
H T MARK button
I X (pause) button
J zREC (record) switch/lamp
K LINE IN (OPT) jack
L MIC (PLUG IN POWER) jack
There is a tactile dot beside the MIC
(PLUG IN POWER) jack.
M i (headphones/earphones)/LINE
OUT jack
N USB connecting jack
O HOLD switch (at the rear)
Slide the switch in the direction of the
arrow to disable the buttons on the
recorder. To prevent the buttons from
being accidentally operated when you
carry the recorder, use this function.
P CHG (Charge) lamp
are tactile dots beside the
N ENT and VOL + buttons.
The display window of the recorder
1
2
3
4 5
6
0
A Disc indication
Shows that the disc is rotating for
recording or playing.
B Battery indication
Shows the approximate remaining
battery power. If the rechargeable
battery is weak, the indication
becomes empty and starts flashing.
C SYNC (synchro-recording) indication
D REC indication
Lights up during recording or file
transfers from the computer. When
flashing, the recorder is in record
standby mode.
E Group indication
7
8
9
qa
F Hi-MD/MD indication
“Hi-MD” lights up when the
operation mode of the recorder is in
Hi-MD mode and “MD” lights up
when the operation mode is in MD
mode.
G Track number display
H “R” (Remain) indication
Lights up when remaining recordable
time is displayed.
I Character information display
Displays the menu items, date, error
messages, etc.
J Track mode (PCM, Hi-SP, Hi-LP, SP,
LP2, LP4, MONO) indication
K Level meter
5
MZ-NH1
The headphones/earphones with a remote control
Using the clip for the remote control
1
2
6
3
7
8
9
0
4
5
A Display window
B Jog lever (NX • ENTER, .,
>)
Operation
Function
Press NX •
ENTER
play, pause, enter
Slide towards cue to the beginning of
.
the previous track,
rewind
.
Slide towards cue to the beginning of
>
the next track, fast
forward
F HOLD switch
Slide the switch in the direction of the
arrow (a yellow mark appears) to
disable the buttons on the remote
control. To prevent the buttons from
being accidentally operated when you
carry the recorder, use this function.
G •DISPLAY, BACKLIGHT button*
H •P-MODE, REPEAT button*
I •SOUND, SOUND SET button*
J Jog dial (•NAVI/ MENU/ENTER)*
* • indicates a function that requires a slight
press of the button.
indicates a function
that requires pressing the button for 2 seconds
or more.
C Clip
D x (stop) • CANCEL button
E VOL +, – buttons
The display window of the remote control
1
2
3
4
A Character information display
B Battery level indication
6
C Disc indication
D SND (sound), SUR (surround)
indications
It may be hard for you to read the indications in the display if the remote
control is attached upside down with the clip in its current position.
In this case, turn the clip in the opposite direction until it attaches firmly,
as shown below.
MZ-NH1
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note 1: The process described in can be performed in any order.
Note 2: Without completing the process described in , the next process can not be performed.
SET
3-2. BOTTOM PANEL SUB ASSY
(Page 7)
3-3. MAIN BOARD
(Page 8)
3-4. UPPER PANEL SUB ASSY
(Page 8)
3-5. CONTROL ORNAMENT BLOCK
(Page 9)
3-6. MECHANISM DECK ASSY (MT-MZNH1-181)
(Page 9)
3-7. GEAR (SA), GEAR (SB)
(Page 10)
3-8. OP SERVICE ASSY
(Page 10)
3-9. DC SSM18D/C-NP MOTOR (SPINDLE) (M701),
DC SSM21A/C-NP MOTOR (SLED) (M702),
DC MOTOR UNIT(OVER WRITE HEAD UP/DOWN) (M703)
(Page 11)
3-10. HOLDER ASSY
(Page 11)
Note: Follow the disassembly procedure in the numerical order given.
3-2. BOTTOM PANEL SUB ASSY
S895
Note: When installing the bottom panel
sub assy, adjust the position of
switch (S895) and knob (hold).
3 bottom panel sub assy
2 two screws
(M1.4) L=1.6
1 two screws
(M1.4) L=1.6
knob (hold)
7
MZ-NH1
3-3. MAIN BOARD
4 two flexible boards
(CN471, 701)
2 Remove two solders.
q; MAIN board
3 flexible cable
4 flexible board
(CN491)
9 leaf spring
(EMC) (2)
8 toothed lock screw
(M1.4)
5 three toothed lock
screws (M1.4)
4 flexible board
(CN501)
7 leaf spring
(EMC) (1)
6 toothed lock screws (M1.4)
1 sheet (shield A)
3-4. UPPER PANEL SUB ASSY
4 two screws
(M1.4) L=1.6
5 two screws (M1.4) L=1.6
6 upper panel sub assy
3 screw (M1.4) L=3.0
B
1 flexible board
(CN471)
A
2 Slide the lever (lock) in the direction of arrow A,
and open the upper panel sub assy in the direction of arrow B.
8
MZ-NH1
3-5. CONTROL ORNAMENT BLOCK
4 two claws
7 flexible board
(CN491)
4 claw
6
5 claw
8 control ornament block
2 battery case lid.
A
3 two screws
(M1.4) L=2.5
1 Open the battery case lid.
3-6. MECHANISM DECK ASSY
(MT-MZNH1-181)
1 two step screws
(MD)
2 mechanism deck assy
(MT-MZNH1-181)
3 battery case
9
MZ-NH1
3-7. GEAR (BSA), GEAR (SB)
1 self tap screw
2 thrust retainer spring
3 washer (0.8-2.5)
5 gear (SB)
3-8. OP SERVICE ASSY
1 Lead screw block assy is turned
and it removes from OP service assy.
2 OP service assy
10
4 gear (SA)
MZ-NH1
3-9. DC SSM18D/C-NP MOTOR (SPINDLE) (M701), DC SSM21A/C-NP MOTOR (SLED) (M702),
DC MOTOR UNIT (OVER WRITE HEAD UP/DOWN) (M703)
3 two screws (M1.4)
2 Remove two solders of flexible board.
4 DC SSM21A/C-NP motor (sled)
(M702)
1 Remove four solders of flexible board.
8 self tap screw
6 three self tap screws
9 DC motor unit
(over write head up/down)
(M703)
7 DC SSM18D/C-NP motor
(spindle) (M701)
5 motor base assy
3-10. HOLDER ASSY
4 Remove the holder assy
to the direction of the arrow A.
2 boss
3 Open the holder assy.
1 boss
A
11
MZ-NH1
SECTION 4
TEST MODE
OUTLINE
A key having no particular description in the text, indicates a set
key.
1. ENTERING THE TEST MODE
Preparation:
Copy the “TestMode_Enter_For_NH1_NH3D_Ver***.exe” folder
of the PC application of the latest version to your PC in advance.
(operating system: Windows 2000, Windows XP)
Also, when using this application, the SonicStage Ver. 2.0 or 2.1 is
necessary, and install it in your PC in advance.
2. OPERATION IN SETTING THE TEST MODE
• When the test mode becomes active, first the Display Check
mode is selected.
• Other mode can be selected from the Display Check mode.
• When the test mode is set, the LCD repeats the following
display.
• When the x key is pressed and hold down, the display at that
time is held so that display can be checked.
Display check mode:
• Display of the main unit
Procedure:
1. If a Simple Burner has run on the PC, finish it (including the
one that is resident in the task tray).
2. Start the “TestMode_Enter_For_NH1_NH3D_Ver***.exe”.
3. Insert the fully charged lithium-ion battery (LIP-4WM).
4. Open and close the top panel of the main unit to wait until the
system reading finished.
5. Connect the main unit and PC by USB cable.
6. Check by device manager screen from property of “My
computer” that the set is recognised to your PC normally.
7. Click the [Enter TestMode] button on the screen of application
8. Disconnect the USB cable, when “OK” message is displayed
on the application screen.
9. Remove the lithium-ion battery.
All lit
All off
Microcomputer
version display
Ver *.***
•
Display of the remote commander
All lit
All off
Screen of the PC application “TestMode_Enter_For_NH1_NH3D_
Ver***.exe”
(“***” is version number)
Note: Once the test mode is activated with this application, the test mode
is then activated forcibly by only turning on the power.
After the repair completed, be sure to release the test mode by using
this application once more.
12
Microcomputer
version
display
001
Ver *.***
3. RELEASING THE TEST MODE
Procedure:
1. If a Simple Burner has run on the PC, finish it (including the
one that is resident in the task tray).
2. Start the “TestMode_Enter_For_NH1_NH3D_Ver***.exe”.
3. Insert the fully charged lithium-ion battery (LIP-4WM).
4. Open and close the top panel of the main unit to wait until the
system reading finished.
5. Connect the main unit and PC by USB cable.
6. Check by device manager screen that the set is recognised to
your PC normally.
7. Click the [Exit TestMode] button on the screen of application
8. Disconnect the USB cable, when “OK” message is displayed
on the application screen.
9. Remove the lithium-ion battery.
MZ-NH1
4. CONFIGURATION OF THE TEST MODE
5. MANUAL MODE
This is mode to adjust or check the operation of the set by function.
Flow of the test mode:
Display Check Mode
001
Ver *.***
Version display → All lit
→ All off → Version display...
Operation of The Manual Mode
1. Enter the test mode (Display Check mode).
2. Press the [VOL+] key to activate the Manual mode where the
LCD displays as shown below.
Display of the remote commander
Manual Mode
000
000
[VOL +] key
Manual
Manual
x key
Number of 1000th place
(000 to 009)
Overall Adjustment Mode
000
[VOL --] key
AdjF**
x key
Key Check Mode
000
[GROUP] key
10
Open the lid
Self-Diagnosis Result Display Mode
3. During each test, the optical pick-up moves outward or inward
while the [FF] or [FR] key is pressed for several seconds
respectively.
4. Each test item is assigned with a four-digit item number; 1000th
place is a top item, 100th place is a major item, 10th place is a
medium item, and unit place is a minor item.
The values adjusted in the test mode are written to the nonvolatile memory (for the items where adjustment was made).
5. To quit the Manual mode, press the x key and return to the
Display Check mode.
000
[FF] key
1 0000
Flow of manual mode operation:
x key
[VOL +] key: 1000th place of item
number increase.
[VOL --] key: 1000th place of item
number decrease.
Top item switching
Sound Skip Check Result
Display Mode (Play)
[FF] key
x key
000
N ENT key
P00r00
Major item switching
x key
Sound Skip Check Result
Display Mode (REC)
000
[T MARK] key
[FF] key
x key
Medium item switching
p00R00
[FF] key
x key
Key Count Mode
[MENU] key
MENU
000
000
x key
Minor item switching
[VOL +] key: 100th place of item
number increase.
[VOL --] key: 100th place of item
number decrease.
[VOL +] key: 10th place of item
number increase.
[VOL --] key: 10th place of item
number decrease.
[FF] key:
[FR] key:
1st place of item
number increase.
1st place of item
number decrease.
[FF] or [FR] key
(press a few seconds)
Adjusted value variation
(Not used in servicing)
[VOL +] key: Increases the adjusted
value.
[VOL --] key: Decreases the adjusted
value.
Adjusted value write
X key: Adjusted value is written.
13
MZ-NH1
6. OVERALL ADJUSTMENT MODE
6-1. Operation of The Overall Adjustment Mode
1. Enter the test mode (Display Check mode).
2. Press the [VOL--] key to activate the Overall Adjustment mode
where the LCD displays as shown below.
Display of the remote commander
000
AdjF**
Disc mark:
Lit the inner segments: Completed the power supply adjustment.
Lit the outer segments: Completed the check of charge function.
“**”:
If “DF” or “FF” is displayed, it mean that completed the servo
overall adjustment.
3. To quit the Overall Adjustment mode, press the
return to the Display Check mode.
x
Display
Close!
DfDis!
NoChg!
NoTmp!
NotCD!
NotM1!
NotH3!
****NG
Description
Dose not close the lid
Unsuitableness disc was inserted
Does not finish the check of charge function yet
Does not setting the temperature correction value
Does not complete the CD Overall adjustment beforethe
MD1 Overall adjustment
Does not complete the MD1 Overall adjustment
before the Hi-MD3 Overall adjustment
Does not complete the Hi-MD3 Overall adjustment
before the Stray Light Offset Overall adjustment
Error of item number “****”
key and
Flow of overall adjustment mode:
Overall Adjustment Mode
000
AdjF**
CD Overall Adjustment Mode
***
[FR] key
6-2. Error Message in The Overall Adjustment Mode
In the Overall Adjustment mode, if an error occurred, it displays as
following table.
CD Run
7. SELF-DIAGNOSIS RESULT DISPLAY MODE
This set uses the self-diagnostic function system in which if an error
occurred during the recording or playing, the mechanism control
block and the power supply control block in the microcomputer
detect it and record its cause as history in the nonvolatile memory.
By checking this history in the test mode, you can analyze a fault
and determine its location.
Total recording time is recorded as a guideline of how long the
optical pick-up has been used, and by comparing it with the total
recording time at the time when an error occurred in the selfdiagnosis result display mode, you can determine when the error
occurred.
Clear the total recording time, if the optical pick-up was replaced.
x key
MD1 Overall Adjustment Mode
[FF] key
***
MD1Run
x key
Hi-MD3 Overall Adjustment Mode
7-1. Operation of The Self-Diagnosis Result Display
Mode
1. Enter the test mode (Display Check mode).
2. Press the [FF] key to activate the Self-Diagnosis Result Display
mode where the LCD displays as shown below.
Display of the remote commander
***
[VOL +] key
HM3Run
***
$$####
x key
Stray Light Offset Overall
Adjustment Mode
***
[VOL --] key
OfsRun
x key
Optical Pick-up Operation
Check Mode
000
[GROUP] key
OPChk
x key
Initialize The Adjustment Values
911
[T MARK] key
ResOK?
x key
(rotation)
14
3. To quit the Self-Diagnosis Result Display mode, press the
and return to the Display Check mode.
x
key
MZ-NH1
Flow of Self-diagnosis Result Display mode operation:
***
The first error
1 ####
[VOL +] key
Display of the remote commander
The last error
N ####
***
One error before
the last
[VOL --] key
***
Two error before
the last
N2####
[VOL +] key
11*
$$$$$$ ##
[VOL --] key
N1####
[VOL +] key
Operation of The Key Check Mode
1. Enter the test mode (Display Check mode).
2. Press the [GROUP] key to activate the Key Check mode where
the LCD displays as shown below.
[VOL --] key
***
[VOL +] key
8. KEY CHECK MODE
This mode is used for key check.
3. When all keys check is OK on the main unit, it displays as
follows.
[VOL --] key
***
Total recording time
R_####
“*”
: Remote commander (0: with, 4: without)
“$$$$$$” : Pressed key name.
When remote commander key is pressed, display becomes
as “r$$$$$”.
When the jog dial is turned, it displays “JOG+ X” or “JOGX” (“X” is number of 1 to 3). If the jog dial is turned four
click, it displays “JOG+OK” or “JOG-OK”.
“##”
: Key voltage of remote commander. (Hexadecimal number)
Display of the remote commander
888
SET OK ##
[VOL +] key
[VOL --] key
7-2. Error Code of The Self-Diagnosis Result Display
Mode
Error code
00
01
02
03
04
05
06
07
08
09
12
13
32
33
34
Description
No error
Attempt to access an abnormal address
High temperature detected
Focus error (no change)
Abnormal rotation of disc
Fault of disc discriminate
Error of access loop (no change)
Error of access loop (with change)
Could not read address
Focus error (with change)
Could not read data with SYNC
TOC address data error
Focus error, ABCD offset error
Tracking error, offset error
Tracking error, X1 tracking error, offset error
When all keys check is OK on the remote commander, it
displays as follows.
Display of the remote commander
888
RMC OK ##
*) Turn the jog dial four click upside and downside to jog test is OK.
4. When all keys check are OK both the main unit and the remote
commander, it display backs to the Display Check mode
automatically.
5. To quit the Key Check mode, open the lid and return to the
Display check mode.
7-3. Clear The Total Recording Time
After replacing the optical pick-up, clear the total recording time.
1. Enter the test mode (Display Check mode).
2. Press the [FF] key to activate the Self-Diagnosis Result Display
mode.
3. Press the [VOL--] key once to display the total recording time
indication.
4. Press the X key and display “ClrOK?”.
5. Press the X key again to display “RecT 0” and clear the total
recording time.
15
MZ-NH1
Ver 1.1
SECTION 5
ELECTRICAL ADJUSTMENTS
1. PRECAUTIONS FOR ADJUSTMENT
1. Adjustment must be done in the test mode only. After adjusting,
release the test mode. A key having no particular description
in the text, indicates a set key.
2. Use the following tools and measuring instruments.
• Digital voltmeter
• Regulated dc power supply (two sets)
• Thermometer (using the “Setting The Temperature Correction
Value”)
• Laser power meter
• CD adjustment disc TDYS-1 (Part No. : 4-963-646-01)
• MD1/HiMD1 hybrid adjustment disc MDW-74/GA1
(Part No. : 4-229-747-01)
• Hi-MD3 adjustment disc HMD1GSDJ
(Part No. : 7-819-098-37) *1
• Remote commander in accessories (with LCD)
• Battery charging stand and AC adapter in accessories
• Lithium-ion battery (LIP-4WM) in accessories
(full charged)
• PC application software for test mode
“TestMode_Enter_For_NH1_NH3D_Ver***.exe” *2
• USB cable
*1) Hi-MD3 adjustment disc (HMD1GSDJ) is consumable.
Therefore if it is used 400 times, exchange it for a new.
*2) Use the newest version every time.
Copy the whole folder of this program to your PC.
Operating system: Windows 2000, Windows XP
When using this application, the SonicStage Ver. 2.0 or 2.1 is
necessary, and install it in your PC in advance.
3. Unless specified otherwise, use the AC adaptor and battery
charging stand in accessories.
2. ADJUSTMENT SEQUENCE
Adjustment must be done with the following order.
Adjustment order:
1. Entering the test mode
2. Initialize the adjustment value
3. Setting the temperature correction value
4. Power supply voltage adjustment
5. Charge function check
6. Laser power check
7. Setting the adjustment values
8. Servo Overall adjustment
9. Resume clear
10. Releasing the test mode
3. ADJUSTMENT OF THE EACH ITEM
3-1. Entering The Test Mode
Refer to the “SECTION 4. TEST MODE”.
3-2. Initialize The Adjustment Value
Procedure:
1. In the test mode (Display Check mode), press the [VOL--] key
to enter the Overall adjustment mode.
2. Press the [T MARK] key and display “911 ResOK?”.
3. Press the X key to display “911 Reset!” and initialize the
adjustment values.
4. Press the x key and back to Display Check mode.
16
3-3. Setting The Temperature Correction Value
Procedure:
1. In the test mode (Display Check mode), press the [VOL+] key
to enter the Manual mode.
2. Press the [FF] key twice, and press the [VOL+] key twice to
display as follows.
Display of the remote commander
130
Temp
3. Press the [FF] key once to select the item number 0131 and
display as follows.
Display of the remote commander
131
SetTmp **
adjustment value (hexadecimal)
4. Measure the ambient temperature.
5. Adjust with [VOL+]/[VOL--] keys so that the adjusted value
(hexadecimal value) becomes the ambient temperature.
(example: 25 °C = 19h)
6. Press the X key to write the adjusted value.
7. Press the x key four times and back to the Display Check
mode.
3-4. Power Supply Voltage Adjustment
Adjustment must be done with the following order.
3-4-1. Setting
Procedure:
1. Apply the voltage of 3.7 V to the battery terminals, and enter
the test mode (Display Check mode).
2. Press the [VOL+] key to enter the Manual mode.
3. Press the [VOL+] key twice to display as follows.
Display of the remote commander
002
POWER
4. Press the [FF] key once, press the [VOL+] key once, and press
the [FF] key once again to display as follows.
Display of the remote commander
210
PwrAdj
5. Repeat the next procedures (3-4-2. PwrAdj Adjustments), and
adjust all contents of “table 3-4-1. PwrAdj Specifications”.
MZ-NH1
3-4-2. PwrAdj adjustments
Repeat the following procedures and adjust all contents of “table 34-1. PwrAdj Specifications”.
ItemNo.
2211
2212
2213
2214
2215
2216
2217
2218
2219
2221
2222
2223
2224
2225
2226
2227
2228
2229
2231
2232
2233
Example Display (Item No. 2211)
211
VC1
**
adjustment value (hexadecimal)
Procedure:
1. Connect the digital voltmeter to measuring point (refer to the
following table) and ground (CL433).
2. Press the [FF] key to change the item number.
3. Adjust with [VOL+]/[VOL--] keys so that the value of digital
voltmeter becomes specification value.
4. Press the X key to write the adjusted value.
5. Press the [FF] key to select the next item.
6. Repeat adjustment from step 1 until item number 2233.
Display
211 VC1 **
212 VC1H N **
213 VC2 **
214 DDC3 L **
215 DDC3 H **
216 REG1 L **
217 REG1 H **
218 REG2 1 **
219 REG2 2 **
221 REG2 3 **
222 REG2 4 **
223 REG3 **
224 VREC 1 **
225 VREC 2 **
226 VREC 3 **
227 VREC 4 **
228 VREC 5 **
229 VREC 6 **
231 VREC 7 **
232 VREC 8 **
233 VREC 9 **
Specification value Measuring point
2.05V +0.02V
CL8003
2.25V ±0.01V
CL8003
1.20V +0.01V
CL603
2.60V ±0.015V
CL604
3.10V ±0.015V
CL604
2.32V ±0.02V
CL362
3.02V ±0.02V
CL362
2.27V ±0.02V
CL509
2.47V ±0.02V
CL509
2.72V ±0.02V
CL509
2.97V ±0.02V
CL509
2.52V ±0.02V
CL516
0.89V ±0.02V
CL624
1.08V ±0.02V
CL624
1.52V ±0.02V
CL624
2.27V ±0.02V
CL624
2.97V ±0.02V
CL624
0.94V ±0.02V
CL624
1.28V ±0.02V
CL624
2.57V ±0.02V
CL624
2.57V ±0.02V
CL624
Note1: “**” is adjustment value (hexadecimal number).
Note2: Ground point of all measuring points is CL433.
Table 3-4-1. PwrAdj Specifications
Adjustment Location:
CL935
LITHIUM-ION
RECHARGEABLE BATTERY
LIP-4WM
C555
R509
K
A
C891
C881
C877
C871
C847
C878
R867
C849
K
A
C873
CL8007
1
C804 C861
C826 R492
R810
C851 C825 R491
C822
R865 R858
D616
8
R493
+ C856
R854
K
C662
R846
CN491
FB801
C602
C805
K
A
C604
9
Q803
R802
IC801
C839
C460
A
C625
C803
R608
D609
K
D617
K
D456
A
A
D610 A
R832
A
FB454
R663
C453
C457
K
10
7
X801
R405
C636 C630
12
6
X872
IC871
3
1
1
3
4
R876
C802
D801
R861
R473
A
R517
C545
A
K
R872
C827
R870
C810
R866
R848
IC873
5
C874 +
C816 +
D455
R453
K K
15
4
IC601
R456
D451
SL803
16
11
FB808
R616
CL8003
20
10
X802
R455
K
FB453
A
1
IC891
R808
C641
FB451
K
D431
K
C574
R502
R501
R895
L870
C823
FB803
SL801
C811
5
6
R855
R856
C821
R813
D803
R868
C801
FB807
C892
C626
C642
C455
C401
R401
R417
C403 +
Q431
C550
L506
C538
C525
C517
C516
C515
C511
R833
R893
FB501
R617
C406
C402 +
R459 R458
D
S
C559 R512 R518
C526
R524
R519
C567 +
C547
C537
C528
C530
C524
C539
L502
C568
R507
C533
R508
C569
C503
C573
C835
ECB
R635
CL603
R827
D603 K
R504
R503
C557
FB502
BP801
+ C838
+ C836
+ C615
+ C632
C628
+ C622
C560
C564 +
+ C556
L507
C845
CN501
C855
C713
C624
A
C521
26
CL509
D501
C522
C570 +
1
C612 +
R656
C527
Q501
C617 +
R636
C529
C513
C531
C562
R526
R561
R885
K
3
R850
K
C519
A
2
FB809
GDS
A
4
R864 C852
D611
2D
1G
1S
C552
IC501
FB503
C814
C643
5
IC804
1
FB810
C715 C717
4
R860
R809
1
R510
L803
FB802
R657
R706
3
D871 L804
CL516
K
C879
C536
C523
R525
2S
2G
1D
A
C890
C880
1
+ C614
R628
R642
Q883
C820
2
R863
C660
IC872
+ C553
C554
B
Q502
C
C558
D884
L802
4
E
L501
C819 +
1 3
Q802
3
C520
R514
IC502
R888
2C
1B
1E
K D601 A
R641
R404
C712
R707
R604
C634
+ C635
R654 C644 R629 R658
R418
2
L504
Q882
Q884
BCE
D
D
S
R884
D
R886 D
G
4
C561
R894
L801
C818 +
C701
C710
C716
R310
R309
C714
C637 +
R638
R403
C409 R415
R882 R883
R902
R952
C702
C709
C708
C707
L303
R637
Q404
D883
56
C456
C351
R474
CN471
43
D
1C
2B
2E
4
1
ECB
R431
R471
R475
IC701
R402
A
R360
R351
R254
Q352
G
11
D
14
C452
1
IC605
L505
1
K
R887 C888
D618
BCE
BCE
SL894
3
Q504
+ C613
ECB
C404
C152
R352 C352
S
IC401
R407
Q251
Q151
C432
FB351
2G
2S
1G
1S
R154
Q351
2D
2D
1D
1D
2
15
D
Q606
1C
2B
2E
1C
2B
2E
C415
R416
C405
C151
R151
R251
C251
R356
FB151
D
A
1E
1B
2C
C407
C370
FB251
CL604
1
42
C638
R357
C410
R354
21
C647
G
A
K
A
IC604
R609
+ C361
R361
C364
22
15
C408
14
Q607
+ C359
+ C358
+ C357
C365
C354
C360
R353
IC351
C368
FB357
C306
K
BP351
C367
FB353
C252
R619
A
28
FB355
FB354
R355
+ C320
C318 +
1E
R364 1B
2C
R363
1E
Q405 1B
2C
1
7
8
10
28
C412
+ C208
R206
R207
C310 +
FB102
C307
C356 +
C362 +
F351
28
D614
BP352
CN701
RB702
C705
BP701 29
+ C312
R650 R633
R358
BP312
22
C311
+ C355
CL362
1 C319
C206
C207 +
FB202
C706
R314
C314
C322
21
FB302
C323 +
7
IC301
R308
15
C321 +
C205
C703
5
R610
C105
C204
R890
R640
8
C324
C104
14
Q881
RB701
C325
C101
C106
R107
C107 +
C941
R944
R940
4
C328
K
C884
C431
IC302
ECB
C566
L503
R505
+ C518
R513
D882
D881
R315
R313
C102
C202
C201
1
+ C108
R106
1
C327
C313 +
C315 +
2
4
C629
C938
C924 +
C916 +
C920
R101
FB101
IC881
3
2E
2B
1C
C316 +
R515
ECB
IC902
5
+ C948
3
R201 R203
R103
ON
Q503
R936
+ C955
OFF
C433
Q951
4
R937
R946
FB201
C934
R935
R938
R947
FB301
R907
4
C942
R927
L904
R904
R933
R925
R939
D902
R929
48
R934
R926
34
50
49
R516
SL892
1C 2B 2E
R945 1E 1B 2C
1 R953
3
C936
K
K D903 A
C919
32
33
A
K D901 A
C905
+ C940
+ C939
K
IC901
C906
R307 C308
R923
C957
3
R956 R957
C932
A
C909 +
C917
SL891
IC903
R954
C931
D906
C910 +
1
C434
64
2
R958
1
R922
C926
R917
SL901
S895
HOLD
C645
2
C894
C903
C928
R924
R931 R941 C929
C927
R918
K
17
C902 18
C911 +
C925
16
L901
R511 C565
+ C949
C912 +
S892
(HALF LOCK)
C575
L902
R520
L903
+ C951
+ C922
A
C913 +
R914
D904
+ C952
R903
C914 +
R912
R906
C954
C901
C918
R908
R910
– MAIN BOARD –
(Conductor Side)
K
A
D491
BP471
CL460
(VBUS GND)
CL433
(GND)
CL453
(VBUS 5V)
CL451
(DC IN 6V)
CL624
17
MZ-NH1
3-4-3. VBsAdj adjustments
Procedure:
1. In the “3-4-2. PwrAdj Adjustments” completed status, press
the [FF] key to display as follows.
Display of the remote commander
6. And [FF] key once again to select the item number 2251 and
display “251 ChgChk **” on the LCD of remote commander.
7. Press the X key confirm that “ChgCOK” is displayed.
8. Press the x key four times and back to the Display Check
mode.
9. Cut the power supply and remove the resistor that connected
to the battery terminals.
240
VBsAdj
2. Apply the voltage of 5 V to the CL453 (VBUS 5V) and CL460
(VBUS GND).
3. Press the [FF] key to change the item number to 2241.
4. Adjust with [VOL+]/[VOL--] keys so that the value of digital
voltmeter becomes specification value. (refer to “table 3-4-2.
VBsAdj Specifications”)
5. Press the X key to write the adjusted value.
6. Press the [FF] key to select the next item, and repeat
adjustments to item number 2243 at the same manner as step
3 to step 5.
Item No.
Display
Specification value
Table 3-4-2. VBsAdj Specifications
7. Press the [FF] key to select the item number 2244, and turn off
the power supply of battery terminal.
8. Adjust with [VOL+]/[VOL--] keys so that the voltage of between
CL935 and CL433 (GND) becomes 4.10 V (− 0.02 V).
9. Press the X key to write the adjusted value.
10. Apply the voltage of 3.7 V to the battery terminal again.
11. Press the x key to display “240 VBsAdj” (Item number:
2240).
12. Turn off the voltage of 5 V to the CL453 (VBUS 5V) and
CL460 (VBUS GND).
13. Press the x key three times and back to the Display Check
mode.
3-5. Charge Function Check
Note1: When perform this check, don’t apply a voltage to battery terminals.
Note2: Be sure to disconnect the AC adapter when connecting the resistors.
Doing so with the power supply connected causes a trouble.
Procedure:
1. Connect the 10 ohms resistor (more than 3 watts) to battery
terminals.
2. Connect the AC adapter to the battery charging stand in
accessories and set the main unit.
3. Enter the test mode (Display Check mode).
4. Press the [VOL+] key once to enter the Manual mode.
5. Press the [VOL+] key twice, press the [FF] key once, press the
[VOL+] key once, press the [FF] key once, press the [VOL+]
key twice to display as follows.
Display of the remote commander
250
18
Display of the remote commander
009
DESIGN
Measuring point
2241 241 REG4 **
1.13 V ± 0.01 V
CL603
2242 242 REG5 **
2.05 V + 0.02 V
CL8003
2243 243 REG6 **
3.30 V ± 0.01 V
CL8007
Note1: “**” is adjustment value (hexadecimal number).
Note2: Ground point of all adjustment points is CL433.
Note3: Refer to page 17 for adjustment location.
ChrgLi
3-6. Laser Power Check
Procedure:
1. In the test mode (Display Check mode), press the [VOL+] key
to enter the Manual mode.
2. Open the lid and press the [FR] key continuously until the
optical pick-up moves to the most inward track.
3. Set the laser power meter so that the laser beam from the optical
pick-up aims at the objective lens of laser power meter at right
angle.
4. Press the [VOL--] key once to display as follows.
5. Press the [FF] key three times to select the item number 9111
and display as follows.
Display of the remote commander
111
LrefPw **
6. Confirm that the value of laser power meter is 0.67 mW ±
21%.
7. Press the [FF] key to select the item number 9112.
8. Confirm that the value of laser power meter is 0.76 mW ±
18%.
9. Press the [FF] key to select the item number 9113.
10. Confirm that the value of laser power meter is 6.25 mW ±
12%.
11. Press the x key four times and back to the Display Check
mode.
MZ-NH1
3-7. Setting The Adjustment Values
3-7-1. Hi-MD3 setting
Preparation:
1. Perform calculation every item based on the data given by the
Hi-MD3 adjustment disc by referring to the following table.
(Round off the value in decimal place)
2. Convert the calculated value into hexadecimal number.
3-7-2. Other setting
1. In the test mode (Display Check mode), press the [VOL+] key
to enter the Manual mode.
2. Press the [FF] key five time to select the item number 0113
and display as follows.
Display of the remote commander
113
Note: The Hi-MD3 adjustment parameters vary depending on the disc,
and therefore use the parameters of the disc used when performing
the adjustment.
Item No.
0211
(*1)
0212
0213
(*2)
0214
0215
0216
Calculating formula (*3)
Pr_nominal / 0.05
Por / 0.05
Kr × (−100)
Pw_nominal / 0.05
Ppw / 0.05
Kw × (−100)
Prmin / 0.05
Pwmin / 0.05
*1) If the “Pr_nominal” value is indicated, use the “Pr_nominal” value
and not used “Por” value.
*2) If the “Pw_nominal” value is indicated, use the “Pw_nominal” value
and not used “Ppw” value.
*3) Round off after the decimal point.
Table 3-7-1. Hi-MD3 adjustment parameter
DistF
**
adjustment value (hexadecimal)
3. Press the [VOL+]/[VOL--] key and set the according value to
each model type and destination referring to the following
table.
4. Press the X key to write the adjusted value.
Destination
US, Australian
AEP, UK
E18, Hong Kong, Taiwan,
Korean, Chinese, Tourist
Setting value
01
81
05
• Abbreviation
E18: 100V - 240V AC area in E model
Table 3-7-2. Mode Type and Destination Setting
3-8. Servo Overall Adjustment
Example of Calculation:
Item No.
0211
0212
0213
0214
0215
0216
Parameter
Pr_nominal 2.50 mW
Kr
−0.3 %/°C
Pw_nominal 7.35 mW
Kw
−0.4 %/°C
Prmin
1.9 mW
Pwmin
5.8 mW
Decimal
50
30
147
40
38
116
Result
Hexadecimal
32h
1Eh
93h
28h
26h
74h
Procedure:
1. In the test mode (Display Check mode), press the [VOL+] key
to enter the Manual mode.
2. Press the [FF] key once, press the [VOL+] key once, and press
the [FF] key once again to display as follows.
Display of the remote commander
210
PwrAdj
3. Press the [FF] key once to select the item number 0211.
4. Adjust with [VOL+]/[VOL--] keys so that the adjustment value
of LCD becomes calculated value.
5. Press the X key to write the adjusted value.
6. Press the [FF] key to next item.
7. Repeat adjustment from step 4 until item number 0216.
Note1: Be sure to adjustment so that the set is horizontal and the LCD is
upside. Unless performed in that state, it is not adjusted correctly.
Note2: If NG is displayed in the middle of this adjustments, perform “3-2.
Initialize The Adjustment Value” and “3-7. Setting The Adjustment
Values” again, then retry this adjustments from step 1.
Procedure:
1. Insert the full charged lithium-ion battery (LIP-4WM)
and enter the test mode (Display Check mode).
2. Press the [VOL--] key to enter the Overall Adjustment mode.
3. Insert the CD adjustment disc (TDYS-1).
4. Put the main unit horizontal so that the LCD becomes upside,
and press the [FR] key.
5. Wait until “CD OK” is displayed on the LCD.
6. Insert the MD1/HiMD1 hybrid adjustment disc
(MDW-74/GA1).
7. Put the main unit horizontal so that the LCD becomes upside,
and press the [FF] key.
8. Wait until “MD1 OK” is displayed on the LCD.
9. Insert the Hi-MD3 adjustment disc (HMD1GSDJ).
10. Put the main unit horizontal so that the LCD becomes upside,
and press the [VOL+] key.
11. Wait until “HMD OK” is displayed on the LCD.
12. Eject the disc.
13. Put the main unit horizontal so that the LCD becomes upside,
and press the [VOL--] key.
14. Wait until “OfstOK” is displayed on the LCD.
15. Press the x key and back to the Display Check mode.
19
MZ-NH1
3-9. Resume Clear
Procedure:
1. In the test mode (Display Check mode), press the [VOL+] key
to enter the Manual mode.
2. Press the [VOL+] key once, press the [FF] key once, press the
[VOL--] key once, press the [FF] key once, and press the [VOL+]
key twice, press the [FF] key three times to select the item
number 1933.
3. Press the X key to resume clear.
4. Press the x key four times and back to the Display Check
mode. And remove the lithium-ion battery.
3-10. Releasing The Test Mode
Refer to the “SECTION 4. TEST MODE”.
Note: Once the test mode is activated with this application, the test mode
is then activated forcibly by only turning on the power.
After the repair completed, be sure to release the test mode by using
this application once more.
20
MZ-NH1
SECTION 6
DIAGRAMS
6-1. BLOCK DIAGRAM – MD SERVO Section –
OVER WRITE HEAD DRIVE
IC601 (1/2)
HR601
OVER
WRITE
HEAD
M703
OVER WRITE
HEAD
UP/DOWN
RF AMP, FOCUS/TRACKING ERROR AMP
IC501
IY
IX
JX
JY
A
B
C
D
RF_IY
RF_IX
RF_JX
RF_JY
56
1
54
55
50
51
52
49
IY
RFO 8
C
D
ADFG 23
RF BUFFER
Q504
101
RFI
TO IC801 (2/3)
(AUDIO SECTION)
108 ABCD
FE 41
109 FE
TE 42
114 TE
SYSTEM CONTROLLER,
DIGITAL SIGNAL PROCESSOR
IC801 (1/3)
153 ADFG
PD-NI 19
142 APCREF_DA
CLK 26
174 FS256_OUT
180 OFTRK
20 PD_BUF
17 PDO_SOURCE
IIN
OPTICAL
PICK-UP
BLOCK
(ABX-U)
VC 38
123 VREF_MON
VREF09 9
PEAK 48
BOTM 47
110 VC
SBUS 33
SCK 32
S-MON 21
251 SSB_DATA
252 SSB_CLK
113 SE
XRESET 35
225 XRF_RST
106 PEAK
107 BOTM
S0
209
210
254
272
S1
PLSE_XDC
CONT
PD_S0
PD_S1
LDPEN
XLSRCK
FOCUS/TRACKING
COIL DRIVE,
SPINDLE/SLED
MOTOR DRIVE
IC701
TRK+
TRK–
FCS+
FCS–
TRK+
TRK+
30 FO2
32 RO2
FI2 28
RI2 27
155 TFDR
154 TRDR
13 FO1
11 RO1
FI1 15
RI1 16
156 FFDR
157 FRDR
UI2 43
VI2 42
WI2 41
216
172
167
168
TRK–
TRK–
35
25
37
24
39
23
26
FCS+
FCS+
U
FCS–
FCS–
L1
L2
82 OUTB
145 VIN
ABCD 40
18 PD_I
MVCC
PVCC
VCC
M
245 175 182 158
OFTRK 45
F
EFM_CLK 63
LATCH 56
84 OUTA
NPPO 43
IX
JX
JY
A
B
15 A_C
14 D_C
EFM 62
FS4
11
10
13
12
ADIP_IN 39
CLK
CLK 60
EFMO
7 VREF10
HB
HBB
HA
HAB
XCS_REC_DRV
CHOPPERCLK
VREF
77
69
78
70
OVER WRITE
HEAD DRIVE
Q601, 602
M702
(SLED)
W
V
MDVCC
REG2 B+
REG3 B+
UO2
CPUI2
VO2
CPVI2
WO2
CPWI2
COM2
PWM2 44
ZI2 22
SLD_MON
SRDR
SLDV
SLDW
159 SFDR
289 HI_Z_SLO
L1 B+
L2 B+
8 UO1
18 CPUI1
UI1 56
VI1 1
WI1 2
6 VO1
19 CPVI1
MZ-NH1
21
21
CPWO1
SPDL_MON
SPRD
SPDV
SPDW
161 SPFD
ZI1 21
290 HI_Z_SPDL
OE 48
238 XRST_MTR_DRV
52 53 54
CLV MON V
CLV MON U
SLD MON W
47 46 45
CLV MON W
• SIGNAL PATH
: PLAYBACK
: REC
CPVO2
CPUO2
V
CPWO2
W
SLD MON V
SLD MON U
M701
(SPINDLE)
PWM1 55
4 WO1
28 CPWI1
17 COM1
CPVO1
CPUO1
U
232
160
162
163
SLCU 169
SLCV 170
SLCW 171
SPCU 164
SPCV 165
SPCW 166
SLD MON U
SLD MON V
SLD MON W
CLV MON U
CLV MON V
CLV MON W
A (Page 23)
MZ-NH1
6-2. BLOCK DIAGRAM – AUDIO Section –
SWITCHING DRIVER,
HEADPHONE AMP
IC351
2 BEEP_IN
BEEP 199
DCLSOUTL
3 DIN2
151
MUTEON
OUT2 15
J351
i
MUTING
Q351
150
4 DIN1
312
296
295
211
243
23
26
25
27
11
(Page 23)
OUT_
17
BEEP2
FROM IC801 (1/3)
(MD SERVO SECTION)
DCLSOUTR
C
OUT1 7
J301
LINE IN
(OPT)
FS512
D_EN2
D_EN1
D_ENREG
D_VCONT_PWM
173 DIN
B+ SWITCH
Q302
OUT_BEEP1 5
MCK
EN2
EN1
ENREG
VCONT
MUTING
Q151, 251
RVDD
F351
RVDD
DTCK
KEY-R
RGND
MUTING
CONTROL
Q352
VC01 B+
A/D CONVERTER, MIC AMP
IC301
XMUTE 212
SDT0
MCLK
BCLK
LRCK
PDN
28 LIN
1 RIN
15 MICL
22 MICR
J302
ADDT
FS256
XBCK
LRCK
XPD_ADC
DTCK 313
RMC_KEY 131
CSN 13
RMC KEY
CN451 (1/2)
(USB)
D871
6
DATA+
REAL TIME
CLOCK
IC871
DATA–
8 OSCOUT
X872
32.768kHz
185 OPT_DET
186 XJACK_DET
187 XMIC_DET
OSCI
OSCO
EEPROM
IC891
: LINE IN
SET_KEY_1
SET_KEY_2
REC_LED/ACCESS_LED
CHG_OPR_LED
PAUSE_KEY
SI1
SO1
SCK1
XCS_LCD
XRST_LCD
HALF_LOCK_SW/
OPEN_SW
OPEN_CLOSE_SW
PROTECT
HIMD_PROTECT
XHOLD_SW
SI0
SO0
SCK0
XCS_NV
REC/DOWNLOAD
SYSTEM CONTROLLER,
DIGITAL SIGNAL PROCESSOR
IC801 (2/3)
: USB input from PC
128
133
124 125
203
244
183
213 214 215 236 192
135
188
184
253
227
• SIGNAL PATH
REG VSTB B+
: PLAYBACK
: OPTICAL IN
E
(Page 23)
LED DRIVE
Q491
: MIC IN
LED DRIVE
Q405
OFF
SDI1
SDO1
SCK1
XCS_LCD
LCD_RST
PAUSE
S892
HALF
LOCK
LCD MODULE
XWK2
XWK4
XWK1
SWITCH MODULE
REC KEY
SET_KEY_1
REC LED
CHG_LED
REC LED
SET_KEY_1
SET_KEY_2
DOWNLOAD
WK_DET
–1
XWK1, XWK2,
XWK4
SO
SI
SCK
XCS
SDO0, SCK0
: USB output to PC
(Page 23) B
2
11
12
1
195
196
197
239
SDO0
SCK0
UOSCO
247
CS_RTC
311
UOSCI
193 USB_WAKE
310
WK_DET
WAKE UP SWITCH
Q803
320
1
2
12
X802
22.5792MHz
319
SIO
SCLK
LEVEL SHIFT
IC873
CE
7 OSCIN
X801
48MHz
VB B+
4
5
200 XOPT_CTL
+2.1V
REGULATOR
IC302
+3.9V
REGULATOR
IC872
VSB
UDP 314
UPUEN 318
UDM 315
3
REG1 B+
D (Page 23)
189 XCS_ADC
AVDD
18 PREL
19 PRER
307
306
309
308
190
CDTI 11
CCLK 12
16 PREOL
21 PREOR
MIC
(PLUG IN POWER)
7
9
8
10
14
MZ-NH1
22
22
S893
OPEN/CLOSE
DETECT
S891–1
PROTECT
DETECT
–2
S891–2
Hi-MD
PROTECT
DETECT
ON
S895
HOLD
MZ-NH1
4-3. BLOCK DIAGRAM – POWER SUPPLY Section –
(Page 22)
E
SDO0 SCK0
SDO0
SCK0
58 DATA
60 SCK
59 STRB
34 XRST2
17 XRST1
B+ SWITCH
Q604, 611
MUTEON 45
VG
B+
OR GATE
IC604
+1.2V
REGULATOR
IC603
REG5 B+
D609
98 REG_OUT
D610
61 VIF
13 VC
14 VC
VC B+
SLEEP_IN
VG
TSBV_IN
REG_IN
DVDD_IN
VSTB_IN
VREF_IN
67 RECP
+1.2V
REGULATOR
IC602
REG F B+
83
101
97
90
105
18
VREC 112
VREC_IN 80
VREC_IN 81
11
40
9
57
REG1 B+
REG2 B+
REG3 B+
B+ SWITCH
Q502, 503
MDVCC
VCO1
VCO2
VSTB
VREF
54 REGO1
51 REGO2
47 REGO3
HVB 8
VB 27
FCRAM_VDD
108 V33RO
+2.5V
REGULATOR
IC804
VO1 12
VO2 39
D883
SWITCHING
Q501
D884
LEVEL
SHIFT
Q882
+2.2V
REGULATOR
IC882
VB B+
D881
REGULATOR
CONTROL
Q881
VOLTAGE
DETECT
IC881
D882
DW_1T 3
DW_1B 2
DW_3T 26
DW_3B 27
VB B+
VB B+
21
22
28
66
73
V3O_1
V3O_2
V3FB
VG2
VG3
VBUS_DET 250
USBHOLD 316
SUSPEND 317
51 VBUS_DET
86 HOLD_OUT
99 SUS_IN
RST_CONT 132
95 RST_IN
VB_MON 121
VBUS_MON 129
HIDC_MON 127
REG5 B+
DRAM_ALONE
B+ SWITCH
Q603
D603
DDC3 B+
PWM_L1 299
PWM_L2 300
DRAM_
VDD_CLR
VB B+
VBUS B+
DC IN B+
SYSTEM CONTROLLER
IC801 (3/3)
L3_2 25
L3_1 24
VBUS
VPDRV
PVBUS
VBUSSEL
CLP
CLM
POWP1
POWP2
54
36
88
43
38
42
37
41
B+ SWITCH
Q605
CN451 (2/2)
(USB)
VOLTAGE
LIMITER
Q606, 607
3
VBUS
1
DCIN6V
8
PWR_WAKE
VI 6
IN1– 12
TYPE1 11
TYPE2 16
CHARGE CONTROL
IC401
Q404
20 I_CTL1
219 73 256 257 207
220
CHG_I_CTL1
L2 B+
(Page 22)
B
FFCLR
D602
FFCLR
FCRAM_VDD
DRAM_HOLD_DET
DRAM_VDD_CLR
DRAM_ALONE
+3V
REGULATOR
IC502
L1 B+
B+ SWITCH
Q883, 884
LG 25
DRAM_
HOLD_DET
FFCLR
FCRAM_VDD
DRAM_HOLD_DET
DRAM_VDD_CLR
DRAM_ALONE
USB IF VDD
VRECO_1 5
VRECO_2 4
93 OSC_OUT
B+ SWITCH
Q801, 802
C (Page 22)
24 VG
VREC B+
L1_1 7
L1_2 6
REG5 OSC B+
MUTEON
DDC3 B+
MDVCC_CTL 204
RECP 181
RECP_MON 231
D (Page 22)
XWK1
WAKE UP SWITCH
Q951
REGI1 55
REGI2 52
REGI3 48
POWER CONTROL
IC601 (2/2)
106 VSTB_OUT
102 TSBV_OUT
REG5 VSTB B+
REG5 TSBV B+
RST_OUT
91 DVDD_OUT
REG4 B+
REC KEY
POWER CONTROL
IC901
87 64 94 59 58
VOLTAGE
DETECT
IC605
(Page 21)
A
XWK1, XWK2,
XWK4
XWK4
XWK2
XWK4 2
XWK2 4
XWK1 5
XRST 136
DACVREFH 141
VCO2 VC01
B+
B+
VRMC 6
XWK3 3
SDO0
SCK0
D_ENVG 297
VSTB
B+
DATA
SCK
HPOUT B+
VBUSSEL2
SLEEP
XCS_PWR_IC
XRST2_DET
218 233 229
RESET SIGNAL
GENERATOR
IC903
+5.5V
REGULATOR
IC902
CLK
CLK 63
N1_VI_CTL
CHG_PWM
CHG_I_CTL2
CHG_I_CTL3
CHG_MON
A7CAL_SW
XRST_CHG_IC
CHG_SEL
CHG_IAMP_CAL
237
240
221
222
122
194
208
230
241
4
7
29
23
22
13
14
18
27
VI_CTL
CHG_CTL
I_CTL2
I_CTL3
A/D
A7CAL_SW
XRESET
I_SEL
IAMP_CAL
MZ-NH1
23
23
12
REGULATOR
Q401
D401
RF1 26
VO 32
BAT+ 31
LITHIUM-ION
RECHARGEABLE
BATTERY
LIP-4WM
BAT– 25
CHG_SW1 30
RS 24
CHG_SW2
BATT_MINUS_MON 130
XGUM_ON 198
11
S431
(BATTERY INSERT DETECT)
5
CHARGE
CONTROL
Q432
CHARGE
CONTROL
Q431
MZ-NH1
• Note For Printed Wiring Boards and Schematic Diagrams
Note on Printed Wiring Board:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
f : internal component.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
(Conductor Side)
Parts face side:
(Component Side)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Main board is multi-layer printed board.
However, the patterns of intermediate-layer have not been included in this diagrams.
• Lead Layouts
surface
Lead layout of conventional IC
CSP (chip size package)
• Waveforms
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f : internal component.
• C : panel designation.
1
IC701 1 (VI1), 2 (WI1),
th (UI1) (Servo on)
7
IC501 wh (CLK) (Servo on)
88 ns
7.6 ms
1 V/DIV, 5 ms/DIV
• A : B+ Line.
• Total current is measured with MD installed.
• Power voltage is dc 6 V and fed with regulated dc power
supply from CL451 (DC IN 6V) and CL460 (VBUS GND).
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : PLAYBACK
(
) : PLAYBACK (servo on)
[
] : PLAYBACK (servo stop)
∗
: Impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
E : PLAYBACK
j : REC
J : OPTICAL IN
F : LINE IN
d : USB input from PC
G : USB output to PC
N : MIC IN
• Abbreviation
E18 : 100V - 240V AC area in E model
JE : Tourist model
2
8
2.7 Vp-p
5.7 µs
11.3 µs
1 V/DIV, 5 µs/DIV
3
1 V/DIV, 20 ns/DIV
IC901 yd (CLK)
2.5 Vp-p
1 V/DIV, 5 µs/DIV
IC501 1 (IX) (Servo on)
9
IC301 8 (BCLK)
2.6 Vp-p
190 mVp-p
354 ns
50 mV/DIV, 200 ns/DIV
4
501 8 (RFO) (Servo on)
1 V/DIV, 200 ns/DIV
q;
IC301 9 (MCLK)
2.9 Vp-p
1.2 Vp-p
88 ns
500 mV/DIV, 200 ns/DIV
5
IC501 ra (FE) (Servo on)
1 V/DIV, 50 ns/DIV
qa
22.8 µs
20 mV/DIV, 1 µs/DIV
6
IC501 rs (TE) (Servo on)
Approx.
350 mVp-p
100 mV/DIV, 1 µs/DIV
MZ-NH1
24
24
IC301 q; (LRCK)
2.6 Vp-p
Approx.
60 mVp-p
1 V/DIV, 10 µs/DIV
qs
2.7 Vp-p
44 ns
1 V/DIV, 50 ns/DIV
IC701 tg (PWM1) (Servo on)
IC801 <czz (OSCO)
3 Vp-p
2.2 Vp-p
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
qd
IC871 8 (OSCOUT)
960 mVp-p
30.8 µs
500 mV/DIV, 50 µs/DIV
MZ-NH1
6-4. SCHEMATIC DIAGRAM – MAIN Section (1/9) –
• See page 36 for IC Block Diagram.
• See page 24 for Waveforms.
TRK-
TRK+
(1/9)
XRST_MTR_DRV
C716
0.1
C714
0.1
R701
0
XRST_MTR_DRV
SLD_CON_W
R703
0
SLD_CON_W
SLD_CON_V
SLD_CON_V
SLD_CON_U
L701
0
SLD_CON_U
L702
SLD_PWM
SLD_PWM
SLD_MON_U
SLD_MON_U
SLD_MON_V
SLD_MON_V
SLD_MON_W
SLD_MON_W
SLD_CON_W
TF1
SLD_CON_V
TF1
RB701
2.2k
TR1
TR1
ZI2
ZI2
ZI1
ZI1
(Page 33)
FR1
M702
FR1
FF1
(SLED)
V
R707
1k
SLEDV
SLD_PWM
FO2
VMF2
RO2
PGND2
VMR2
UO2
VMU2
VO2
WO2
VMVW2
VI2
UI2
PGNDUV2
W
SLD_CON_U
PGNDW2
SLEDW
WI2
CN701
10P
C703 0.022
C701 0.022
N
C702 0.022
U
FF1
CLV_CON_W
CLV_CON_W
TF1
CLV_CON_V
TR1
CLV_CON_U
FI2
CLV_CON_V
RI2
PWM2
CLV_CON_U
SLD_MON_U
CLV_PWM
SLEDU
COM2
CPUO2
CLV_PWM
SLD_MON_V
CLV_MON_U
SLEDN
HD_DRV-
OVER WRITE
CLV_MON_V
CPWI2
GND1
C713
0.1
CLVV
FOCUS/TRACKING COIL DRIVE,
E1
CPVI1
0.022
CLV_MON_V
CPVO1
CPUI1
CPUO1
COM1
PWM1
RI1
CLV_MON_U
E2
CLV_PWM
(Page 30)
FO1
VMF1
FI1
PGND1
RO1
VMR1
VMU1
FF1
UO1
PGNDUV1
VI1
WI1
UI1
RB702
10k
VMVW1
FR1
CLV_CON_U
PGNDW1
C710
0.022
C709 0.01
C708
0.022
C707 0.01
C705 0.01
C706
CPWI1
IC701
SC981583EPR2
CPWO1
ZI1
ZI1
SPINDLE/SLED MOTOR DRIVE
VG
CLV_MON_W
V
CLV_MON_W
ZI2
ZI2
VC
CLVU
N
CLVN
W
CLV_MON_W
WO1
U
CLV_MON_V
R706 0
CLVW
(SPINDLE)
CPVI2
CPWO2
XRST_MTR_DRV
OE
M701
CLV_MON_U
SLD_MON_W
HD_DRV+
HEAD UP/DOWN
CPUI2
CPVO2
C712
0.1
VO1
M703
A1
A2
A3
A4
CLV_CON_V
L703
0
CLV_CON_W
L704
22µH
R702
0
R704
0
(Page 26)
C717
0.1
C715
0.1
FCS+
FCS-
A5
D1
D2
D3
(Page 29)
C1
(Page 27)
MZ-NH1
25
25
B4
B3
B2
B1
(Page 28)
MZ-NH1
• See page 36 for IC Block Diagrams.
6-5. SCHEMATIC DIAGRAM – MAIN Section (2/9) –
(2/9)
D601
MA2Z748001S0
XCS_REC_DRV
C660
0.1
REG_DACVREFH
REG_F
SUSPEND
4FS
SCK0
SDO0
VBUS_DET
D610
MA2Z748001S0
VOLTAGE DETECT
EFM
XRST1
EFM_CLK
1
RECP
HAB
HA
1
HBB
C655
HB
SUSPEND
C656
USB_HOLD
USB_HOLD
RECP
RECP
D609
MA2Z748001S0
EFM_CLK
EFM_CLK
EFM
IC605
XC61CN1702NR
EFM
XCS_REC_DRV
+1.2V REGULATOR
R603 470k
NC
IC603
R1180Q121C-TR-F
Q604,611
B+ SWITCH
VBUS_DET
+1.2V REGULATOR
IC602
R1160N121B-TR-F
C619 1
VDD
R643
220k
VOUT
VOUT
GND
VSS
VBUS_DET
R604
0
C630
0.1
C621 10 6.3V
VIN
GND
ECO
CE
VOUT
VDD
XCS_REC_DRV
NC
XRST2
C625
0.1
XRST2
RST_CONT
RST_CONT
XRST
R630
0
XRST
SDO0
C601
1
R634
100k
(Page 33)
C636
0.1
SDO0
SCK0
-1
SCK0
4FS
-2
4FS
C614
22 6.3V
C629
0.1
Q604
XP4601-TXE
R644
470k
SLEEP
SLEEP
RMC_DTCK
R608
1
R645
470k
RMC_DTCK
A1
A2
3.3V
C643
2.2
R647 0
USB_HOLD
3.3V
REG5_VSTB
REG5_VSTB
REG5_TSBV
SCK
DATA
VIF
CLK
EFM
PGND4
VO3
GND
RECP
CH
HAB
HBB
VG2
GND
CL
VCP
PGND4
HB
HA
PGND2
EFM_CLK
HOLD_OUT
VBUSSEL2
Q611
SI1410EDH-T1
OUTB
NC_AI2
D613
MA2Z748001S0
VRECIN
VG
OUTA
S
VRECIN
REG5_TSBV
RST_OUT
REG5_REG
NC_M12
REG5_REG
REG5_OSC
REG5_OSC
LATCH
REG4_DVDD
XWKO
REG4_DVDD
REG_F
RST_OUT
VBUS
CL603
WAKEC
CRST
V33UO
REG_DACVREFH
REG_DACVREFH
C602 0.1
REG4_DVDD
XRST2
PVBUS
REG_F
R628
22
C612 22 6.3V
DVDD_IN
C644
4700p
VBUS_DET
C613 22 6.3V
DVDD_OUT
VBUSREF
C604 0.1
HOLDC
OR GATE
L5_2
REG5_OSC
IC604
TC7S32FU(TE85L)
OSC_OUT
PGND5
SLEEP_IN
PGND5
RST_IN
POWFB
C658
22
10V
SLEEP
R631 470k
RST_CONT
V
R632 1M
PGND2
L5_1
XRST
REG_IN
G
R657
220
R640
1M
(Page 25)
REG_OUT
SUS_IN
RST_OUT
IC601
SC901585VAR2
C662 0.01
R648
22k
VBUSSEL
POWER CONTROL
SUSPEND
PGND2
D604
MA22D2800LS0
L607
100µH
PGND5
OVER WRITE HEAD DRIVE,
REG5_REG
CLM
R641
1
POWP2
∗
TSBV_IN
R642
1
INP3
REG5_TSBV
CSP(Chip Size Package)
TSBV_OUT
INP2
C615 22 6.3V
V33R
CLP
C651 4.7
R663
220
D618
MA2SD3100LS0
PGND1
POWP1
VSTB_IN
VPDRV
C616 22 6.3V
C654 0.1
VSTB_OUT
A3
A4
L601
4.7µH
RF2
BATSEL
C641
0.01
DTC2
V33RO
R616
1k
R654
2.2M
C659
4.7
INM2
D611 MA2SD3100LS0
REG5_VSTB
RF1
INM3
C617 22 6.3V
IMM1
C642
0.022
DW_38
DW_37
33USEL
L3_2
L3_1
PGND3
V30_2
V30_1
UP_38
VREFIN
PGND3
PGND3
PGND1
PGND1
VC
VC
UP_18
GND
UP_17
INP1
NC_A1
L1_1
3.3V
L1_2
VREC
DW_IT
DTC1
VRECQ_2
DTC3
0.022
VRECQ_1
C620
DW_1B
R605
10k
R651
2.2
RF3
R617
10k
NC_M1
R629
2.2M
V3FB
C611 0.01
A5
R612
2.2M
CL624
R658
0
CL604
C645
0.01
C638
1000p
HBB
HAB
HA
HB
C626
0.01
F1
R622
2.2
R620
2.2
R621
2.2
R656
0
R623
2.2
R637
0
D603
MA22D2800LS0
S
Q602
MCH6617
C633
0.01
R635
0
S
C622
10
6.3V
-1
R660
0
OVER WRITE
W601
HR601
HEAD DRIVE
D607
MA22D1700LS0
C632
47
6.3V
C628
1
HEAD
R653
0
R633
100k
Q605
NTHC5513T1
R650
2.2M
R619 220
B+ SWITCH
L606
Q606,607
VOLTAGE
S
S
-1
D616
MA22D1700LS0
D617
MA22D1700LS0
-1
C637
10
6.3V
R638
0
L605
100µH
Q603
NTHC5513T1
B+ SWITCH
C635
47
6.3V
C674
33p
100V
W602
OVER WRITE
R636
0
Q601,602
-2
D606
MA22D1700LS0
C624
220p
C634
1
D602
MA22D2800LS0
R625 470k
R668
0
S
-2
-1
S
-2
Q606
RTQ035P02TR
S
LIMITER
-1
-2
D614
MA8056-L-TX
D608
MA2SO3000LS0
R624 470k
C646 0.047
D605
MA2SO3000LS0
C648 0.047
(Page 27)
J1
-2
Q601
CPH5614
S
C649
0.1
C663
1000p
Q607
XP4601-TXE
J2
R610
10k
C650
10
6.3V
J3
R609
220k
C653
10
10V
C652
10
10V
C647
0.047
(Page 32)
C639 0.1
D615 MA22D2800LS0
G1
I1
I2
G2
(Page 29)
MZ-NH1
26
26
H9
H10
H8
H7
H6
H5
H4
H3
H2
(Page 31)
H1
(Page 28)
G3
(Page 32)
MZ-NH1
6-6. SCHEMATIC DIAGRAM – MAIN Section (3/9) –
• See page 36 for IC Block Diagram.
• See page 24 for Waveforms.
B4
B3
B2
B1
(Page 25)
(3/9)
F1
R505
10
C528 0.1
C524
0.01
R510
0
(Page 26)
C554
0.1
SSB_CLK
SSB_DATA
XRST_RF
R525 0
C519
0.1
R526
0
+3V REGULATOR
C553
4.7
6.3V
C530
1
VREF
ABCD
FE
TE
C523
0.1
S0
L503
10µH
S0
S1
S1
IC502
R1180Q3018-TR-F
C561
1
XLDON
XLDON
VOUT
VDD
PLSE_XDC
GND
PLSE_XDC
CE
C536
0.022
C537
1
LC_DRV1
C539
1
LC_DRV1
LC_DRV2
R561
220k
LC_DRV2
PEAK
PEAK
BOTM
C562
1
BOTM
OFTRK
OFTRK
CP
TE
DVCC
CPOUT
SCK
SBUS
VGIN
DGND
VC
CIG
XRESET
NPPO
ADIP_IN
ABCD
L501
0
FE
TE
TE
FE
FE
ABCD
ABCD
CN
VREF
AVCC2
LC_DRV2
R503
100k
R504
100k
R507 2.2k
DFTRK
CN501
26P
TRK+
FCS+
TRK-
Q501
MCH6604
TRK-
BOTM
CON
PEAK
ADFG
RF AMP,
ADIP
S_MON
C550 0.047
D
FOCUS/TRACKING ERROR AMP
A
IC501
SN761059ZQLR
(Page 33)
SSB_CLK
ADIP
S_MON
VPP_LPF
S_MON
APCREF_DA
APCREF_DA
SMON
VC
B
∗
C
CSP(Chip Size Package)
VC
PD_BUF
RFI
APCREF_DA
RFI
PD_NI
AVCC
MDVCC_CTL
C552
0.01
C538
1000p
PD_I
JX
L2
MDVCC_CTL
A_FS256
A_FS257
PDO_SOURCE
XLDON
VIN
JY
RF_JX
RF_JY
RF_IY
RF_IX
VREF09
C573
1000p
RFO
PS
IX
C570
4.7
6.3V
VREF10
IY
PVCC
IIN
VIN
PDO_SINK
OFC_C2
CL509
PLSE_XDC
L507
0
OFC_C1
FB502
0
EQ
PLSE_XDC
AGND
CONT
A_C
O_C
FB501
SSB_CLK
SSB_DATA
S
SWITCHING
L1
C547 0.047
CCSL2
S
-2
-1
FCS+
SSB_DATA
ADIP
TRK+
FCS-
C545 0.1
PEAK
C569
0.01
FCS-
XRST_RF
CLK
BOTM
R508 2.2k
XRST_RF
A_FS256
TON_C
LC_DRV1
VREF
OFTRK
C513
0.01
C568
0.01
CPGND
LDK
C503
1000p
MDVCC
GND
F
C521 10p
VCC
S1
S1
C522 10p
C525
4700p
VREF
C531
0.01
C533
0.01
JY
JX
IY
C
C517 0.1
C511 0.1
B
C515 0.1
A
C516 0.1
IX
VC
D
S0
S0
R501
2.2k
R502
1k
L502
10µH
CL516
C518
4.7
6.3V
C529
0.1
C527
0.1
C557
0.1
C520
0.1
C556
4.7
6.3V
L504
10µH
R1
MDVCC_CTL
FB503
0
L505
10µH
Q502
2SA1745-6.7-TL
R513
10k
Q502,503
(Page 33)
L506
10µH
R514
47k
R517
10k
R515
10k
B+ SWITCH
C559
4700p
R512
0
C558
1000p
∗ C574
470p (US, E18, JE)
1000p (EXCEPT US, E18, JE)
Q503
2SC4738F-Y/
GR(TPL3)
R516
47k
C560
0.1
C564
4.7
10V
R524
220
Q504
2SC4627J-C
(TX).SO
R509
0
RF BUFFER
C555
4700p
R520
470
C566
0.1
RFI
VIN
D501
MAZS068008SO
R518
47k
C574
∗
R519
1k
C565
0.1
R511
0
C567
4.7
6.3V
C526
100p
L1
L2
K2
K1
(Page 29)
(Page 28)
MZ-NH1
27
27
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
MZ-NH1
• See page 36 for IC Block Diagram.
(Page 25)
K1
K2
(Page 27)
C1
6-7. SCHEMATIC DIAGRAM – MAIN Section (4/9) –
(4/9)
M1
(Page 29)
UDP
UDP
UDM
UDM
UDP
UDM
(Page 33)
G1
G2
G3
(Page 26)
MINUS_MON
MINUS_MON
VBUS_MON
VBUS_MON
VB_MON
VB_MON
CHG_PWM
CHG_PWM
C405
0.1
CHG_OPR
CHG_I_CTL1
CHG_I_SEL
CHG_CTL
CHG_MON
CHG_I_CTL3
MINUS_MON
CHG_I_CTL2
CHG_CAL
CHG_CTL
CHG_OPR
CHG_SW
CHG_SW
CHG_XRST
CHG_XRST
CHG_I_SEL
CHG_I_SEL
CHG_I_CTL1
CHG_I_CTL1
R401
2.2k
C401
0.1
R417
2.2k
CHG_MON
Q404
DTC144EETI
CHG_MON
CHG_I_CTL3
(Page 33)
CHG_I_CTL3
INVERTER
CHG_CAL
CHG_CAL
CHG_I_CTL2
CHG_I_CTL2
XGUM_ON
XGUM_ON
HIDC_MON
HIDC_MON
R405
0
I_SEL
PGND
I_CTL1
GND
A/D
RS
I_CTL3
R418
100k
BATC457
2200p
AD_SEL
TYPE2
RF1
CFB
CHG_XRST
IAMP_CAL
IAMP_CTL
AMP_SEL
A7CAL_SW
CHG_SW
FB451
C452
2200p
R455
1M
CHARGE CONTROL
I_CTL2
IN1-
IC401
MM1655LCBE
CHG_SW1
NC
R458
2.2M
VBUS
CHG_CTL
VI
CHG_SW2
VI2
CL453
(VBUS 5V)
VI_CTL
V0
FB454
DCIN6V
PWT
LF451
WDT
VG
CL451
(DC IN 6V)
R402
0.022
CN451
14P
(USB)
LED_CTL
-2
PWR_WAKE
Q405
UP04313008S0
R403
2.2
1/2W
DATA-
VGH
CL460
(VBUS GND)
CL433
(GND)
C456 2200p
C455 2200p
NC
NC
-1
R453
2.2M
NC
DATA+
R404
1
1W
R407
0
VBUS_MON
LED DRIVE
WK_DET
HIDC_MON
R456
470k
FB453
GND
CHG_LED
C415
0.1
TYPE1
BAT+
CHG_CTL
R459
220k
R415 2.2k
CHG_OPR
CHG_PWM
SW_A
SW_B
GND
XGUM_ON
GND
LITHIUM ION
MINUS_MON
W431
R411
100k
RECHARGEABLE
R431
1M
R432
1
R433
0.47
CONTROL
C402
22
10V
C403
22
10V
C406
0.1
R416 1M
REGULATOR
C412 0.1
CHARGE
C410 0.1
Q401
FZT968TA
Q431,432
C409 0.01
S
C408 0.1
2200p
DETECT
C453
C454 470p
C431 2200p
D451
MAZW068H0LS0
C433 2200p
D455 MAZS868008SO
D456 MAZS06800SO
S431
BATTERY INSERT
VB_MON
D401
FTIJ3TP
Q432
FZT688B-TP
Q431
SI2302DS-T1
C407 0.1
W432
C404
1000p
LIP-4WM
3.7V 370mAh
D431
MA22D2800SL0
C434
1000p
BATTERY
R421
100k
R412
0
R413
2.2M
R414
220k
(US, E18, JE)
C432
2200p
C575
1000p
CHG_LED
CHG_LED
S1
S2
C460
1 (E18, JE)
470p (EXCEPT E18, JE)
(Page 32)
MZ-NH1
28
28
MZ-NH1
6-8. SCHEMATIC DIAGRAM – MAIN Section (5/9) –
• See page 36 for IC Block Diagrams.
• See page 24 for Waveform.
H8
H9
H10
H7
H6
H5
H1
H4
H3
H2
(Page 26)
(5/9)
L1
L2
N1
(Page 27)
XRST1
C957
0.1
NC
VIN
VSS
C925
0.1
VOUT
C914
10
6.3V
C922
22
6.3V
C951
100
6.3V
C952
100
6.3V
C928
100p
C949
22
10V
N3
R952 R953
47k
47k
C929
1000p
R956
47k
C926
1000p
D1
C954
0.1
WK_DET
GENERATOR
HALF_LOCK
REC_KEY
XRST2
RESET SIGNAL
IC903
XC61CN1702NR
RMC_KEY
N2
L903
10µH
(Page 25)
C905
1
D901
MA2Z748001S0
R922 100k
R917 220k
R914
10k
R918 470k
C903 1000p
D3
-2
WAKE UP SWITCH
R954
470k
R923
0
L906
220µH
D904
MA2Z748001S0
-1
Q951
XP4601-TXE
R957
470k
C927 100p
D2
R910
22k
D903
MA2Z748001S0
R908
22k
R941 0
R912
220k
REG5_VSTB
R958
0
R924
470k
C911
C912
10 16V
C913
10 16V
C906 1
L901
100µH
FFCLR
XWK4
XWK3
XWK1
XWK2
VRMC
LVB
HVB
VSTB
VC1
VCO1
L1
VO1
L1
PGND1
PGND1
R906 100k
10 16V
C902
0.1
0.022
10 16V
R903 1M
10 16V
C910
SLEEP
CRST1
CLK
4FS
SL901
SEQSEL
C931 2.2
OTC1
MOT
RF1
SCK
SCK0
XCS_PWR_IC
C917
0.1
INM1
STRB
CTL
DATA
VG
VREF
SDO0
L902
100µH
C932 0.01
POWER CONTROL
LG
CL935
M1
GND
IC901
SC901584EPR2
PGND3
REGI1
VB
REGO1
VGSEL2
REGC1
VGSEL1
R925
47k
C934 2.2
R933 220k
REGO2
C939
22
6.3V
R934 22k
C919
0.022
REGC2
C940
22
6.3V
REGI3
REGO3
REGC3
MUTEON
DW_2Q
DW_2T
VC2
VCIN
VCO2
VO2
L2
L2
PGND2
R907
10k
REG2G
PGND2
DTC2
XRST2
RF2
CRST2
R904
1M
N4
REGI2
INM2
(Page 28)
R931 0
XRST1
XRSTIADJ
C918
C909
C901
0.1
C936 2.2
R926
100k
R947 47k
R946 100k
R935 100k
R936 47k
C948
22
6.3V
R927
1k
C938 2.2
R937 22k
R939
47k
L907
D906
MA2Z748001S0
220µH
D905
MA2Z748001S0
D902
MA2Z748001S0
R929
100k
R938 47k
L904
10µH
MUTEON
D_ENVG
R902
100
R944
0
R945
0
VOUT
N5
NC
VIN
VSS
CE
IC902
XC62HR5502WR
+5.5V REGULATOR
C916
10
6.3V
C920
0.1
C924
47
6.3V
C955
22
10V
R940
220k
C942
1
C941
1
N6
MZ-NH1
29
29
(Page 31)
MZ-NH1
6-9. SCHEMATIC DIAGRAM – MAIN Section (6/9) –
• See page 36 for IC Block Diagrams. • See page 24 for Waveforms.
(6/9)
SCK0
+2.1V REGULATOR
IC302
XC6219B212MR
VIN
NC
CE
R314
0
C321
47
6.3V
L303
10µH
C328
1
OPT_DET
C325
0.1
OPT_DET
XJACK_DET
C323
10
6.3V
C324
0.1
XJACK_DET
DIN1
B+ SWITCH
R304
100k
VSS
(Page 33)
Q301
2SA2018TL
R308
0
ADDT
C320
2.2
10V
DIN1
R301
1k
XOPT_CTL
C319
0.1
C322 0.1
SCK0
C327
1
VOUT
SDO0
SDO0
C202
1
R201
47k
C102
1
R101
47k
R305
100
DIN1
J301
FB303
XJACK_DET
XCS_ADC
LRCK
XPD_ADC
SDO0
R310 1k
C313
C101
100p
FB304
OPT_DET
R207
22k
R107
22k
R106
10k
47 6.3V
PREOR
MVDD
PRENR
MICL
PREOL
CSN
PDN
FB201
C201
100p
R206
10k
C311 0.1
MVSS
IC301
AK5356VN-L
XPD_ADC
FB101
(OPT)
C312
47 6.3V
MVCM
MIC AMP
CCLK
XCS_ADC
PRER
SCK0
PREL
XMIC_DET
C318
2.2
10V
MRF
R309 1k
CDTI A/D CONVERTER,
XMIC_DET
LINE IN
MPWR
LRCK
XCS_ADC
XPD_ADC
R103 22k
RIN
MCLK
PRENL
(Page 33)
LIN
FB301
C305
100p
MICR
C304
100p
D301
MAZS068008SO
FS256
XBCK
C310
10
6.3V
C302 2200p
XBCK
VCOM
BCLK
AVDD
XBCK
DVSS
LRCK
LRCK
AVSS
R315
0
DVDD
FS256
SDTO
ADDT
ADDT
FS256
R203 22k
XOPT_CTL
XOPT_CTL
C303
0.1
R306
10k
R307
100
XMIC_DET
J302
C314 0.1
FB202
C315
10 6.3V
C316
22 6.3V
FB102
C208
4.7
6.3V
FB302
C205
0.1
R313
10
C105
0.1
C108
4.7
6.3V
C308
1000p
C206
1000p
C107
47
4V
C106
1000p
C204
2200p
C307
1000p
C104
2200p
C207
47
4V
E1
E2
BP312
O2
O1
(Page 25)
(Page 31)
MZ-NH1
30
30
MIC
(PLUG IN POWER)
MZ-NH1
6-10. SCHEMATIC DIAGRAM – MAIN Section (7/9) –
• See page 36 for IC Block Diagram.
I2
I1
(Page 26)
(7/9)
O1
O2
BP352
(Page 30)
N1
Q1
N2
N3
(Page 33)
R360
0
R361
10
D_VREG0
D_VREG0
D_VCONT_PWM
D_VCONT_PWM
DCLSOUTR
DCLSOUTR
DCLSOUTL
DCLSOUTL
BEEP
BEEP
D_ENVG
D_ENVG
D_ENREG
D_ENREG
D_EN2
C364
2.2
D_EN2
D_EN1
(Page 33)
D_EN1
FS512
C361
47
6.3V
FS512
FS512
XMUTE
XMUTE
R354
0
XMUTE
WK_DET
WK_DET
D_EN1
REC_KEY
REC_KEY
Q352
UN9113J-(TX).SO
D_EN2
D_ENREG
RMC_KEY
RMC_KEY
HALF_LOCK
MUTING
HALF_LOCK
CONTROL
FFCLR
FFCLR
XCS_PWR_IC
XCS_PWR_IC
SWITCHING DRIVER,
OUT_BEEP1
R355
1M
D352
DF8A6.8FK(TE85R)
OUT_BEEP2
OUT2
CFB
VREF
VCONT
VREG
VDD01
VREG0
VSS0
J351
/LINE OUT
VDD02
FB355
RMC_DTCK
RMC_KEY
RVDD
FB354
DTCK
FB353
KEY_R
RGND
FB357
R352
47k
MUTEON
D_VCONT_PWM
C306 2200p
F351
0.25A
125V
C370
1
NC
VSS0
OUT1
C252 1000p
IC351
CXD9811K(TE4)
DIN1
R357
0
R351
1k
VG
R364 0
C353 1000p
DCLSOUTR
D252 MA2S111-TX
CH
C152 1000p
MCK
VDD
EN1
CL
BEEP_IN
R363 0
DIN2
(Page 29)
VSS
D152 MA2S111-TX
DCLSOUTL
EN2
BP351
ENVG
MODE_B
BEEP
ENREG
HEADPHONE AMP
FB351
C151 0.1
FB151
C251 0.1
FB251
R353
22k
R358
0
L152
47µH
R356
0
N4
Q351
NTHD4508NT1G
C154
220
2.5V
CL362
MUTING
S
N5
L252
47µH
-1
S
R154
2.2k
-2
R254
2.2k
C155 0.1
C253 0.22
C153 0.22
C255 0.1
C368 0.22
C367 1
C362 10 6.3V
C354 2.2
C360 2.2
C359 47 6.3V
C365 1
C357 47 6.3V
C358 47 6.3V
C355 47 6.3V
C356 47 6.3V
C254
220
2.5V
Q151
2SC5585TL
Q251
2SC5585TL
C351
0.47
N6
Q151,251
MUTING
C352
0.1
R251
2.2k
R151
2.2k
P1
(Page 32)
MZ-NH1
31
31
(Page 32)
MZ-NH1
• See page 36 for IC Block Diagrams.
6-11. SCHEMATIC DIAGRAM – MAIN Section (8/9) –
• See page 24 for Waveform.
J2
J3
J1
(Page 26)
(8/9)
C873
2p
X872
32.768KHz
C877
0.1
C878
0.1
CN471
11P
REAL TIME
REC_KEY
CLOCK
REC_KEY
SET_KEY_1
SET_KEY_1
PAUSE
CIN
VSS
CS_RTC
REC_LED
OSCIN
/INTR
OSCOUT
PAUSE
C871
0.1
REC_LED
XCS_LED
XCS_LED
SDI1
R473 100
SDO1
R474 100
LCD
VDD
IC871
R2061K01-E2
SDI1
D871
MA2SD32008S0
VCC
LCD_RST
R475 0
VSB
LCD_RST
/VDCC
SIO
SCLK
CE
SCK1
R471
0
SCK1
DVDD
DGND
+3.3V REGULATOR
IC872
R1180Q331C-TR-F
LEVEL SHIFT
IC873
TC7SZ126AFE
SDI0
MODULE
SDO1
CE
GND
R871
220k
GND
R872
0
VDD
VOUT
T1
C879
1
C874
47
6.3V
VCC
C880
1
T2
R491 4.7k
SCK0
SDO0
C881
0.1
REG5_VSTB
T3
T4
CHG_LED
T5
IC882
R1180Q221B-TR-F
CN491
8P
R492
4.7k
CE
SET_KEY_2
GND
VDD
T6
VOUT
SET_KEY_1
SET_KEY_1
SGND
+2.2V REGULATOR
CHG_LED
SWITCH
WK_DET
R882
100k
WK_DET
MODULE
R493 0
REC_LED
DRAM_HOLD_DET
D883
MA2Z748001S0
D881
MA2Z748001S0
SET_KEY_2
FFCLR
(Page 33)
R885
47k
R894
10k
REC_LED
CONTROL
FFCLR
WK_DET
C883
1
WK_DET
REC_KEY
R881
1M
C884
0.01
C890
0.1
1
REGULATOR
IC881
XC61CN3102NR
C885
DETECT
-1
S
Q884
SI1410EDH-T1
-1
-2
-2
Q882
XP4314-TX
Q883,884
Q883
XP4314-TX
B+ SWITCH
R888
0
D884
MA22D2800LS0
R883 100k
Q881
UN9214J-(TX).SO
VOLTAGE
R890 10k
VIN
NC
VSS VOUT
DGND
FFCLR
R887
220k
D882
MA2Z748001S0
REC_KEY
DOWNLOAD
LEVEL
T7
SHIFT
R884
220k
C888
0.1
R886
2.2M
REC_KEY
RMC_KEY
DRAM_ALONE
HALF_LOCK
DRAM_VDD_CLR
RMC_KEY
HALF_LOCK
REG5_REG
XCS_PWR_IC
XCS_PWR_IC
(Page 31)
BL891
S891-1
S891
XRST
XRST
C894 1000p
RMC_DTCK
S891-2
NC
NC
NC
NC
VCC
SDI0
Hi-MD PROTECT
SO
XHOLD
NC
BL892
R893
0
NC
IC891
AK5614CN
XWP
DETECT
SCK0
SCK
S892
SDO0
GND
(US, E18, JE)
SLEEP
RMC_DTCK
-2
XCS
PROTECT
UMD_PROTECT
XCS_NV
R895
0
4FS
SLEEP
DETECT
R892
100k
(HALF LOCK)
SI
HALF_LOCK
NC
4FS
NC
SCK0
SCK0
NC
SDO0
SDO0
NC
RST_CONT
NC
XRST2
RST_CONT
-1
R891
100k
NC
D491
MAZS068008SO
PROTECT
XRST2
S893
(OPEN/CLOSE DETECT)
3.3V
3.3V
(Page 26)
BL894
C892 100p
REG5_VSTB
REG5_VSTB
REG5_TSBV
EEPROM
REG5_TSBV
REG5_REG
REG5_REG
REG5_OSC
HOLD
ON
C891
0.1
REG5_OSC
REG4_DVDD
O/C_SW
S895
OFF
REG4_DVDD
XHOLD_SW
REG_F
REG_F
REG_DACVREFH
REG_DACVREFH
P1
(Page 31)
CHG_LED
S1
S2
BP471
(Page 28)
MZ-NH1
32
32
MZ-NH1
• See page 24 for Waveform. • See page 42 for IC Pin Function Description.
6-12. SCHEMATIC DIAGRAM – MAIN Section (9/9) –
SDO0
SDO0
(9/9)
SCK0
SCK0
(Page 30)
WK_DET
T1
RECP
SL801
R834
220k
RECP
EFM_CLK
R854
0
EFM_CLK
EFM
CLV_PWM
CLV_CON_V
CLV_CON_W
CLV_MON_V
CLV_MON_U
SLD_CON_W
SLD_CON_V
SLD_MON_V
SLD_MON_U
DIN1
SLD_MON_W
A_FS256
R825 0
SLD_CON_U
EFM_CLK
EFM
OFTRK
PAUSE
OPT_DET
PROTECT
O/C_SW
XMIC_DET
XJACK_DET
XPD_ADC
XCS_ADC
LCD_RST
SDO0
SDI0
CHG_SW
R867 0
BEEP
SCK0
R866 0
XOPT_CTL
REC_LED
MDVCC_CTL
DRAM_ALONE
S1
S0
CHG_XRST
SDI1
D_ENREG
SDO1
XMUTE
R846
47k
C847
0.1
Q803
2SC4738F-Y/GR
(TPL3)
WAKE UP
SWITCH
R810
0
R813
0
CHG_SW
JOG_B
XGUM_ON
VBUS_DET
XGUM_ON
VBUS_DET
CHG_XRST
IAMP_CAL
SSB_DATA
CHG_XRST
SSB_DATA
CHG_I_CTL1
NC
SSB_CLK
CHG_I_CTL1
SSB_CLK
UMD_PROTECT
CHG_I_CTL2
SPCV
SPCU
SPDW
SPCW
SLDV
SLDW
SLCV
SLCU
SLCW
DIN
SRDR
MNT0
FS256_OUT
MNT1
CHOPPERCLK
MNT2
MNT3
OFTRK
RECP
EFMO
OPT_DET
PROTECT
PAUSE_KEY
XJACK_DET
XMIC_DET
FF1
FFDR
TF1
SPFD
OPEN_CLOSE_SW
XCS_ADC
XPD_ADC
NC
XRST_LCD
A7CAL_SW
USB_WAKE
SI0
SO0
SCK0
BEEP
XGUM_ON
XOPT_CTL
LAM_REQCHK
MDVCC_CTL
4FS
FR1
TFDR
TR1
TRDR
SPRD
ADIP
ADFG
SFDR
RTCK
R855 0
DCLSOUTL
R856 0
DCLSOUTR
DCLSOUTL
DCLSOUTR
VREFR
D_VCONT_PWM
CHG_I_CTL2
AOUTR
HIMD_PROTECT
CHG_I_CTL3
SLD_PWM
FS4
XCS_LCD
JOG_A
XCS_NV
CHG_SW
CHG_PWM
R869
1M
HIDC_MON
N1_VI_CTL
GND_SW
CS_RTC
HIDC_MON
CLV_CON_U
FRDR
SPDV
R852
0
CS_RTC
VB_MON
VB_MON
XRST_MTR_DRV
CHG_MON
CHG_MON
LAM_SPREQ
VBUS_VB_CTL
MINUS_MON
REC_LED/ACCESS_LED
LAM_NAME
DRAM_ALONE
PD_S0
PD_S1
XMUTE
D_ENREG
SI1
SO1
SCK1
SLD_MON
AOUT_SEL
FFCLR
SLEEP
CHGI_CTL1
SLBUSY
CHGI_CTL2
CHGI_CTL3
XTEST
XRF_RST
VREC_SEL
XHOLD_SW
XRST2_DET
CHGI_SEL
XCS_REG_DRV
XRST_CHG_IC
MINUS_MON
T_MARK_SW
CHG_OPR
VBUS_MON
RECP_MON
D_VCONT_PWM
VBUS_MON
RXD
R836
47k
VBUS_DET
SPDL_MON
VBUS_DET
XCS_PWR_IC
TXD
R845
220k
XCS_REC_DRV
XCS_REC_DRV
(Page
28)
REG5_REG
C813
0.047
EFM
(Page
26)
R858
2.2k
R876
0
FB803
0
USB_HOLD
R857
0
R865 0
R861 100
SCK1
SLD_CON_U
FFCLR
SLEEP
CHG_I_CTL3
CHG_I_CTL2
XRST_RF
XHOLD_SW
RECP
XRST2
CHG_I_CTL1
R828
2.2k
USB_HOLD
CLV_CON_U
R835
470k
SUSPEND
SUSPEND
CHG_I_SEL
C855
0.1
XCS_PWR_IC
T7
XCS_LED
T6
XCS_NV
(Page 32)
C851
0.1
CHG_CTL
CHG_CAL
CHG_LED
CHG_PWM
T4
XRST_MTB_DRV
T5
CHG_LED
XGUM_ON
T3
CLV_MON_W
T2
CHG_OPR_LED
PLSE_XDC
CHG_I_CTL3
AOUTL
LDPEN
CHG_I_SEL
XCS_REC_DRV
CHG_I_SEL
VREFL
CHG_TYPE2
VIN
DRAM_HOLD_DET
CHG_CTL
CHG_CTL
VIN
DRAM_HOLD_DET
DRAM_VDD_CLR
CHG_PWM
CHG_PWM
R839
0
AD3EXTC
DRAM_VDD_CLR
CHG_CAL
CHG_CAL
AD2ENDF
ADC3VREFH
TEST
APCREF_DA
APCREF_DA
CHG_OPR
CHG_OPR
REG_DACVREFH
DACVREFH
SRAM_MODE
XRST_MTR_DRV
R823
10k
XRST_MTR_DRV
SLD_CON_W
SLD_CON_V
R862
0
SLD_CON_V
SLD_CON_U
REG5_REG
PLL3EXTCO
HSALF
SLD_CON_W
SLD_CON_U
MON0
PLL3EXTCI
MON1
PLL2EXTCO
PLL2EXTCI
MON2
SLD_PWM
SL803
SLD_PWM
MON3
XRST
MON4
HALF_LOCK_SW
C814
0.1
C817
0.1
C812
1
R840
0
C843
0.1
C810
0.1
XRST
SLD_MON_U
HALF_LOCK
SLD_MON_U
SLD_MON_V
SLD_MON_V
MON5
RADIO_ON
MON6
REC_KEY/DOWNLOAD
MON7
RST_CONT
MON8
RMC_KEY
MON9
BATT_MINUS_MON
SLD_MON_W
REC_KEY
SLD_MON_W
TF1
RST_CONT
TF1
TR1
RMC_KEY
TR1
ZI2
ZI1
R814 10k
R827
10
ZI2
XLDON
MINUS_MON
VBUS_MON
ZI1
VBUS_MON
XLSRCK
FR1
(Page
25)
WK_DET
FR1
TAT
WK_DET
TAN
HIDC_MON
FF1
HIDC_MON
FF1
R870 0
CLV_CON_W
CLV_CON_W
DCIN_DET
NAR
CLV_CON_V
CLV_CON_V
IDO
SET_KEY_2
SAK
SET_KEY_1
LRCKI
VREF_MON
XBCKI
CHG_MON
CLV_CON_U
CLV_CON_U
C825 1000p
SET_KEY_2
C826 1000p
SET_KEY_1
R837 2.2k
CHG_MON
CLV_PWM
VREF
CLV_PWM
CLV_MON_U
CLV_MON_U
C827
CLV_MON_V
CLV_MON_V
0.1
VB_MON
VB_MON
DATAI
CLV_MON_W
SYSTEM CONTROLLER,DIGITAL SIGNAL PROCESSOR
CLV_MON_W
SI3
D_VREG0
D_VREGO
IC801
CXD2681-222GG
SO3
C803 0.01
ADC1EXTC
∗
SO
SO
APC
SCK3
SI
SI
CSP(Chip Size Package)
SI4
D803
MA2SD32000SB
DCHG
XLDON
XLDON
R868
0
ADRT
SO4
R847 0
PLSE_XDC
PLSE_XDC
AUX1
SCK4
LC_DRV1
TE
LC_DRV1
SCS3
TE
SCS4
SE
LC_DRV2
S_MON
LC_DRV2
PEAK
ZI2
BOTM
ZI1
PEAK
ADRB
HI_Z_SLD
BOTM
OFTRK
TE
HI_Z_SPDL
ADIO
SET_CODE0
VC
SET_CODE1
FE
VC
R830
0
OFTRK
FE
TE
FE
ABCD
FE
SET_CODE2
ABCD
SET_CODE3
BOTM
ABCD
BOTM
ABCD
VREF
D_EN1
PEAK
VREF
XRST_RF
(Page 27)
D_EN1
PEAK
D_EN2
CLTV
C809
D_EN2
XRST_RF
SSB_DATA
0.1
R817 1k
D_ENVG
SSB_DATA
FILO
D_ENVG
SSB_CLK
SSB_CLK
DADT
FILI
PWM_L1
PCO
PWM_L2
RFI
LC_DRV1
ADIP
R818 R819
2.2k
1k
R815 220k
ADIP
R821 2.2M
R820
220
C808
1
LC_DRV2
S_MON
R822
1M
RFI
S_MON
C805 0.47
APCREF_DA
APCREF_DA
ASYI
I2C_1
C804 0.01
VC
VC
ASYO
I2C_2
RFI
REG5_REG
R849 0
RFI
MDVCC_CTL
JTAG0
EBIFVSS7
JTAG1
EBIFVDD7
CLKIN2
EBIFVSS6
FS256
EBIFVDD6
R848 0
MDVCC_CTL
C861
22p
R811 R812
10k 100k
A_FS256
A_FS257
FS256
R864 0
FB810
0
ADDT
R843 0
LRCK
R863 0
FB809
0
XBCK
R809 0
FB802
0
Q801,802
OSCI
UPUEN
FS512
UOSCI
DRAMVSS0
DRAMVDD4
DRAMVDD3
DRAMVDD2
DRAMVDD1
DRAMVDD0
IFVSS_2
IFVSS_1
IFVDD_4
IFVDD_3
IFVDD_2
IFVDD_1
VSS_2
VSS_1
VSS_0
USBIFVDD
MSJTAGVDD
MAIFVDD
TSMVDD
USBOSCVDD
OSCVDD
DAVSS
DVDD25LPF
DAVDD
AVSS6
AVDD6
AVSS5
AVDD5
AVSS4C
AVDD4C
AVSS4B
AVDD2
AVDD1C
AVSS1B
AVDD1B
AVSS1A
AVDD1A
DVSS1_11
DVDD1_11
DVSS1_10
VSS_3
DVDD3
DVSS1_9
DVDD1_9
DVSS1_8
DVDD1_8
DVSS1_7
DVDD1_7
DVSS1_6
DVDD1_6
DVSS1_5
DVDD1_5
DVSS1_4
DVDD1_4
DVSS1_3
DVDD1_3
DVSS1_2
EBIFVSS2
FS256
LRCK
C835
0.1
LRCK
XBCK
R850
0
C811
0.1
EBIFVSS0
+2.5V REGULATOR
IC804
XC61CC2502NR
XPD_ADC
C822
0.1
C823
0.1
L802
22µH
L870
C820
0.1
3.3V
XPD_ADC
REG5_VSTB
10µH
C839
0.1
R824
10
C816
47 6.3V
C818
47
6.3V
D801 MA2SD3100LS0
REG5_OSC
REG5_REG
R1
CL8007
CL8003
L801
Q1
(Page 31)
MZ-NH1
33
33
NC
C852
0.1
C845
0.1
XMIC_DET
(Page 27)
VSS
47 6.3V
C849
0.1
C821 100p
REG_F
XCS_ADC
XMIC_DET
R860
1M
EBIFVSS1
XBCK
XCS_ADC
Q801
XP152A12C0MR
EBIFVDD2
C819
R833
0
REG4_DVDD
ADDT
FS256
C838 10 6.3V
XOPT_CTL
XOPT_CTL
L804 10
FB801
C836 10 6.3V
DIN1
L803 10
DIN1
(Page 30)
EBIFVDD3
VOUT
X801
48MHz
XJACK_DET
ADDT
S
VIN
XJACK_DET
R826 0
OPT_DET
R801
4.7k
C856 47 6.3V
OPT_DET
R832 22k
DCLSOUTL
R802
47
DVDD1_2
DCLSOUTL
R807 2.2k
DCLSOUTR
DCLSOUTR
R806 4.7k
BEEP
DVDD1_10
SUSPEND
DVSS1_1
(Page
31)
BEEP
AVDD4B
SUSPEND
XMUTE
XMUTE
AVSS4A
D_ENREG
D_ENREG
Q802
2SK1838-TE85L
EBIFVDD1
AVDD4A
USBHOLD
AVSS3
USB_HOLD
D_VREG0
D_VREG0
AVDD3
UDM
AVSS2
D_EN2
DVDD25SVAD
UOSCO
UDP
FVSS0
DTCK
DVDD1_1
R805 22
DVSS1_0
R804 22
D_EN2
FVDD0
0
RMC_DTCK
D_EN1
D_EN1
R859
1M
S
EBIFVSS3
SRAMVDD1
FCRAMVSS1
FB808
D_ENVG
D_ENVG
B+ SWITCH
EBIFVDD4
SRAMVSS1
OSCO
FCRAMVDD1
FS512
R808 1k
SRAMVSS0
FS512
X802
22.5792MHz
SRAMVDD0
C802
10p
FS512
EBIFVDD0
DRAMVSS2
D_VCONT_PWM
EBIFVSS4
C801 10p
FB807
0
D_VCONT_PWM
EBIFVDD5
XBCK
DVDD1_0
(Page 28)
EBIFVSS5
LRCK
FCRAMVSS0
UDM
ADDT
FCRAMVDD0
UDP
DRAMVSS1
VIN
VIN
MZ-NH1
6-13. PRINTED WIRING BOARD – MAIN Section (1/2) –
• Semiconductor
Location
6
7
8
9
10
11
MAIN BOARD (COMPONENT SIDE)
A
S891
S891-1
(PROTECT DETECT)
-1
S891-2
Hi-MD
PROTECT DETECT
-2
B
L907
L906
C
K
A
S893
OPEN/CLOSE
DETECT
D905
Q301 B C E
C304
R304
R306 C302
D301 K
D
S431
BATTERY INSERT
DETECT
C883
A
IC602
C616 +
C639
IC603
2G 2S 1G 1S
2G 2S 1G 1S
C651
Q605
C654
2D 2D 1D 1D
L601
R826
C808
R421
J351
i /LINE OUT
MZ-NH1
34
34
R433
B
R668
C
R660
B
E
A
C649
10
1G
D606
A
CN451
(USB)
C254 +
C154
C153
C155
L252
1D
K
+
11
1-861-115-
(11)
C253
S
C454
2G
R622
2D
Q601
D401
C255
1
A
K
K
C663
L152
D607
C650 +
C674
LF451
Q401
R411
E
K
R623
C817
C813
1D
2G
2S
RGND
C
D605
D608
J
C646 R620 C648 R621
R413 R412
R432
C843
R840
R624
R815
A
1S
1G
2D
K
R862
R625
I
K
Q432
D602
A
A
R811
R812
R823
R836
R828 R834
R835
Q602
R825
D152
KEY_R
R821 R818 R820 R839
R845
5
L605
R414
R852
R805
R804
R806
R807
4
A
DTCK
R817 C809
R869
8
C611 R631
L606
R822 R819 R847
R824
1
RVDD
R849
R857
H
C620 R605
R648
K
D352
R612 R632
R843
R837
R871
R801 R814
D252
R651
C633
R830
A
C659
2D 2D 1D 1D
Q603
C812
D604
D615
K
R892 R891
L703
FB304
A
2
C305
K
R647
L607
3
C353
C652 +
R301
K
R702
R704
1
L704
4
1
3
C653 +
F
DVCC
4
R630
5
S
4
3
K
G
D
D
S
C621 +
R859
Q801
L701
IC882
Q611
J301
LINE IN
(OPT)
A
R634
D
D
G
DIN
DGND
K
D
1C
2B
2E
C303
R881
R305
2
1
C658 +
L702
R645
C619
E
Q604
R701
R703
1E
1B
R643 2C
R603
G
FB303
A
C885
D613
C601
C-9
H-8
H-7
J-5
I-5
F-6
D-6
F-7
E-7
E-6
5
R644
Q301
Q401
Q432
Q601
Q602
Q603
Q604
Q605
Q611
Q801
4
C655
E-7
F-7
E-8
3
C656
IC602
IC603
IC882
2
R653
Ref. No. Location
D152
G-10
D252
F-10
D301
D-9
D352
G-10
D401
I-9
D602
H-6
D604
F-9
D605
I-5
D606
I-6
D607
I-5
D608
I-4
D613
D-7
D615
F-8
D905
C-10
1
: Uses unleaded solder.
MZ-NH1
6-14. PRINTED WIRING BOARD – MAIN Section (2/2) –
3
4
5
C845
C503
C827
R870
C810
R866
R867
A
C881
C877
C871
C847
C873
R846
R802
Q803
R876
A
C814
IC801
C878
C849
K
9
CN491
FB801
8
R493
SWITCH
MODULE
1
R810
C822
R827
R854
C805
C826 R492
C851 C825 R491
R865 R858
D616
R861
K
C803
R832
K
A
10
7
X801
C839
C460
(EXCEPT US, E18, JE)
CL451
(DC IN 6V)
CL453
(VBUS 5V)
6
+ C856
+
K
12
C804 C861
D617
D456
A
4
X872
C602
C662
1
1
3
CL8007
D801
D609
K
A
C457
C604
5
C874 +
ECB
C802
A
C625
CL8003
C891
R855
15
IC873 IC871
4
3
FB808
A
FB454
C453
D610 A
SL803
16
11
K
A
D491
11
1-861-115-
(11)
J
(CHASSIS)
K
A
R872
20
10
+
CL460
(VBUS GND)
1
IC891
R808
C816
A
CL433
(GND)
K
K A
D451
Q431 K A
D455
BP471
C636 C630
K
FB453
SL801
C811
5
6
R848
R813
FB803
D803
R868
C801
R856
FB807
C821
C823
L870
+ C838
+ C836
C615
C632
R895
1
C892
K
R833
R893
FB501
X802
IC601
R455
R663
R453
K K
K
D431
C574
C573
C626
R616
D457
S
C559 R512 R518
C547
C525
R502
R501
A
OPTICAL PICK-UP
BLOCK
ABX-U
C835
R850
R809
K
FB502
CL603
FB809
GDS
D611
A
3
R864 C852
(CHASSIS)
HR601
OVER WRITE HEAD
MZ-NH1
35
35
Ref. No. Location
D431
I-5
D451
I-6
D455
I-5
D456
I-7
D457
J-7
D491
J-12
D501
D-12
D601
H-8
D603
G-7
D609
I-7
D610
I-7
D611
F-8
D614
F-5
D616
I-7
D617
I-7
D618
I-7
D801
H-11
D803
F-11
D871
E-8
D881
C-8
D882
C-8
D883
C-8
D884
D-8
D901
C-3
D902
C-3
D903
C-3
D904
B-3
D906
C-3
C570 +
BP801
4
IC8042
C641
R456
R459 R458
R517
C545
C550
C567 +
C538
C517
C516
CN501
26
CL509
1
R656
C642
C406
C403 +
D
R471
C555
R509
R524
C526
R519
L506
C528
C537
C530
C524
C531
C533
C515
C521
R617
R402
C402 +
D501
C522
R504
R503
C557
C539
L502
C568
R507
C569
C527
C513
Q501
CL516
L507
2D
1G
1S
C552
C529
C511
C560
C564 +
+ C556
L504
K
IC501
C519
L803
R860
+
R635
R508
C562
R526
R885
Q882
Q884
C820
C879
CL624
R636
C523
R525
2S
2G
1D
A
Q883
R894
D871 L804
C880
C614
C643
C819 +
K D601 A
R642
L802
C612 +
+
C628
+ C622
C624
C635
C634
C713
C712
R707
R404
L501
D884
C536
B
Q502
R510
C
C558 FB503
IC502
C855
+
R654 C644 R629 R658
R641
3
E
C554
(CHASSIS)
R863
5
2
C520
C561
D
D
S
FB802
C715 C717
C716
C714
C638
R561
R882 R883
R884
BCE
C890
4
+ C518
+ C553
K
L801
+
C818
C701
C710
C660
R657
1
1C
2B
2E
FB810
R952
C942
C702
C703
C709
C708
C707
R310
R309
+
R604
R473
LCD
MODULE
R520
C914 +
R923
R314
C325
L303
+
C361
R403
R431
C351
R474
CN471
CL604
L503
R505
R514
C617 +
D603 K
C455
R360
Q352
R475
R418
A
C452
C405
R351
BCE
G
11
R638
ECB
FB451
1
R706
3
D618
Q151
BCE
Q802
D883
K
4
R888
2C
1B
1E
1
4
L505
1
56
C456
R352 C352
R254
2G
2S
1G
1S
Q404
ECB
Q504
+ C613
ECB
C432
FB351
C306
C152
2D
2D
1D
1D
D D
IC401
R407
Q251
R154
Q351
R416 C415
R417
C151
R151
C251
R251
R356
FB151
4
3
1
R637
Q606
S
D
R886 D
G
C407
C370
FB251
R361
R354
21
FB357
1C
2B
2E
1C
2B
2E
1E
1B
2C
IC872
IC605
2
2
1 3
15
D D
R401
15
C410
C404
C367
FB353
1
43
R628
22
C408
14
A
C368
BP351
C364
R353
FB354
Q607
C359
+
28
IC351
10
42
R609
C647
G
C409 R415
C358
+
1E
R364 1B
2C
R363
1E
Q405 1B
2C
1
8
FB355
C252
K
R357
C357
+
C354
C360
C362 +
7
CN701
IC701
C645
+ C208
C355
+
C365
C356 +
I
C957
R315
A
A
R887 C888
14
C637 +
C206
R206
C318 +
D614
BP352
R355
+ C312
C311
(CHASSIS)
F351
+ C320
C401
CL362
28
R650 R633
R358
BP312
22
K
A
SL894
IC604
C412
C307
F
1 C319
FB102
C310 +
R207
FB202
R890
28
C321
C322
21
FB302
Q881
BP701 29
R308
IC301
C205
C207 +
C941
R940
R933
7
C323 +
15
C105
C204
8
R610
MIC
(PLUG IN POWER)
14
A
D881
RB702
C705
K
C884
C431
IC902
C706
R515
R513
D882
1
R640
C324
C104
R902
C940
+
R944
C939
C936
5
C328
C314
C102
C202
C101
C107 +
J302
H
4
C313 +
C315 +
2
4
IC302
R619
R106
C106
R107
R307 C308
3
RB701
C316 +
+ C108
10
IC881
2E
2B
1C
1
ON
Q503
C327
3
R103
R101
G
+ C955
R201 R203
C201
FB201
+ C948
OFF
C433
Q951
5
R516
SL892
ECB
R936
R313
R946
4
1C 2B 2E
4
R937
FB101
N
C938
R938
R947
M701
(SPINDLE)
E
3
R954
R956 R957
C934
R935
+
C924
C916 +
C920
R907
R929
R927
L904
R904
M
W
R934
R926
48
SL891
CL935
R945 1E 1B 2C
3
1 R953
R925
50
49
R939
U
V
+
K
A
34
D902
FB301
M703
OVER WRITE
HEAD UP/DOWN
C919
W
C905
V
D
32
33
A
M702
(SLED)
C906
1
IC903
C932
IC901
K
K D901 A
N
2
C629
D906
K D903 A
C
C917
• Semiconductor
Location
12
C566
S895
HOLD
C434
64
C894
R958
1
R922
C926
R914
C928
SL901
C931
U
C954
L903
2
S892
(HALF LOCK)
L901
C903
R931 R941 C929
C927
17
C902 18
C925
16
R924
K
C912 +
C909 +
11
R511 C565
R918
+
C951
+ C922
+
C952
D904
+ C949
1
10
C575
L902
R608
R908
R903
C910 +
9
LITHIUM-ION
RECHARGEABLE BATTERY
LIP-4WM
(CHASSIS)
R906
C911 +
8
(US, E18, JE)
C913 +
B
7
R912
A
C918
C901
A
R910
MAIN BOARD (CONDUCTOR SIDE)
6
R405
2
R917
1
: Uses unleaded solder.
IC301
IC302
IC351
IC401
IC501
IC502
IC601
IC604
IC605
IC701
IC801
IC804
IC871
IC872
IC873
IC881
IC891
IC901
IC902
IC903
E-4
D-5
G-4
H-5
C-11
C-9
H-7
E-7
E-7
F-6
H-9
E-8
G-11
E-8
G-11
C-7
F-11
C-4
C-6
B-6
Q151
Q251
Q351
Q352
Q404
Q405
Q431
Q501
Q502
Q503
Q504
Q606
Q607
Q802
Q803
Q881
Q882
Q883
Q884
Q951
I-4
H-4
I-4
I-4
G-6
G-5
I-4
D-9
C-9
B-9
B-11
G-5
G-5
E-8
H-12
C-7
C-8
D-8
D-8
C-6
MZ-NH1
• IC Block Diagrams
IC301 AK5356VN-L
PREL
PRENL
PREOL
MICL
RS
I_CTL3
A/D
GND
I_CTL1
20 19
18 17
16
15
24
23
22
21
20 19 18 17
MICR 22
14 PDN
RESET
A/D
CONVERTER
BAT– 25
MVDD 23
I_SEL
AD_SEL
PRENR
PRER
21
PGND
PREOR
IC401 MM1655LCBE
RF1 26
MVCM 25
VCOM
MRF 26
MPWR 27
16 TYPE2
13 CSN
12 CCLK
11 CDTI
CONTROL
REGISTER
INTERFACE
MVSS 24
IAMP_CAL 27
15 CFB
AMP_SEL 28
MIC POWER
SUPPLY
14 IAMP_CTL
+ –
10 LRCK
9 MCLK
8 BCLK
+ –
13 A7CAL_SW
LIN 28
+ –
AUDIO
INTERFACE
CONTROLLER
A/D
CONVERTER
VREF
VREF
I_CTL2 29
CHG_SW1 30
VCOM
12 IN1–
1
2
3
4
5
6
7
RIN
VCOM
AVDD
AVSS
DVSS
DVDD
SDTO
BAT+ 31
VO 32
11 TYPE1
TIME
DIVIDER
OSC
10 WDT
SWITCHING
CHARGE
CONTROL
ON/OFF
CONTROL
RECEIVER
DET
SWITCHING
CIRCUIT
COMPARATOR
BLOCK
CHARGE CONTROL
ON/OFF
CL
CH
VG
NC
OBEEP2
VSS
OUT2
C351 CXD9811K
21 20
19
18
17
16
15
HEADPHONE AMP
(N-N)
LEVEL
SHIFTER
PRE
DRIVER
VDD 24
LEVEL
SHIFTER
LEVEL
SHIFTER
LEVEL
SHIFTER
BEEP
AMP
1
2
3
4
5
6
7
DIN2
DIN1
OBEEP1
VSS
OUT1
MZ-NH1
36
36
3
4
5
6
7
CHG_SW2
VI
CHG_CTL
CFB
VREF
VCONT
VREG
VREGO
8 VDDO1
BEEPIN
CONTROL
LOGIC
LINE AMP
(P-N)
MODEB
25
26
27
28
REGULATOR
VSS 22
13
12
11
10
9
2
VI_CTL
PRE
DRIVER
1
PWT
14 VDDO2
VG
LINE AMP
(P-N)
HEADPHONE AMP
(N-N)
EN1
EN2
ENREG
ENVG
CHARGE SWITCH
CONTROL
BEEP
AMP
LEVEL
SHIFTER
MCK 23
VREF
VI2
CHARGE
PUMP
–
+
ERROR LED
CONTROL
9
LED_CTL
WAKE-UP
CONTROL
8
PWR_WAKE
MZ-NH1
ABCD
ADIP-IN
VC
CIG
DGND
XRESET
VGIN
SBUS
SCK
CPOUT
CP
DVCC
42 41
40
39
38
37
36
35
34
33 32
31 30 29
TE
FE
IC501 SN761059ZQLR
SERIAL
INTERFACE
28 CN
27 CPGND
26 CLK
POWER
SUPPLY
VCC2
VCC
TEMP
A+B+C+D
I+J
NPP
TON
CSL
AW+DW
TON PEAK
TON BOTM
ADIP
TE
TWPP
PK/BTM
AW
CSLO
NPPO 43
AVCC2 44
VCC2
OFTRK
OFTRK 45
T-ON
TON-C 46
ADIP
BOTM 47
PEAK 48
D
A
B
C
PEAK/
BOTTOM
49
50
51
52
AVCC 53
S-MONITOR
VREF09
A-C
D-C
MALFA
MIJ
AWBPF
DW
DWBPF
OFTTH
APC
ADIP-BPF
VFREF0.4
I-J
25 CCSL2
24 CDN
23 ADFG
22 WPP-LPF
TPP/WPP
TE
21 SMON
ABCD
20 PD-BUF
19 PD-NI
18 PD-I
VCC
APC
JX 54
JY 55
LY 56
FE
17 PDO-SOURCE
16 PDO-SINK
RF
2 3
4
5 6
7
8
9
10 11 12 13
14
LX
PS
EQ
AGND
OFC-C1
OFC-C2
VREF10
RFO
VREF09
RF_LX
RF_LY
RF_JY
RF_JX
D-C
15 A-C
1
37
MZ-NH1
OUTA
VG
OUTB
VRECIN
VRECIN
PGND2
HA
HB
PGND4
CL
VCP
VG2
GND
CH
HAB
HBB
GND
RECP
VG3
PGND4
VBUSSEL2
EFM CLK
EFM
VIF
CLK
DATA
SCK
NC M12
IC601 SC901585VAR2
84
83
82 81 80
79
78 77
76
75 74 73 72 71
70 69
68
67
66 65
64
63 62
61
60
59 58
57
CHARGE PUMP
VG
VG3
VIF
NC A12 85
56 LATCH
EFM BOTTOM
PRE DRIVER
HOLD OUT 86
RST OUT 87
55 XWKO
WAKE
CONTROL
HOLD
LOGIC
BUFFER
LVDT
VBUS
EFM TOP
PRE DRIVER
PVBUS
53 WAKEC
PVBUS 88
VBUS
CRST 89
52 V33UO
51 VBUS DET
LVDT
DVDD IN 90
DVDD OUT 91
54 VBUS
DAC
SYSTEM
BANDGAP
REFERENCE
50 VBUSREF
49 L5 2
HOLDC 92
48 PGND5
47 PGND5
OSC OUT 93
2.0V
RESET
SLEEP IN 94
CONTROL
46 POWFB
RST IN 95
45 L5 1
PGND2 96
RESET
LOGIC
REG IN 97
REG OUT 98
H-BRIDGE
DRIVER
44 PGND5
43 VBUSSEL
SUS IN 99
42 CLM
PGND2 100
41 POWP2
TSBV IN 101
TSBV OUT 102
40 INP3
39 INP2
POWER SWITCH
DRIVER
CIRCUIT
V33R 103
38 CLP
PGND1 104
37 POWP1
BUS POWER
STEP DOWN CONVERTER
DRIVER
VSTB IN 105
VSTB OUT 106
BATSEL 107
VPDRV
36 VPDRV
SELFPOWER
STEP UP-DOWN CONVERTER
DRIVER
V33RO 108
35 RF2
34 DTC2
RF1 109
33 INM2
INM1 110
32 INM3
DTC1 111
PWM
DAC
31 DTC3
PWM
VREC
VREF
BUFFER
VREC STEP UP-DOWN
CONVERTER DRIVER
VREC 112
30 RF3
V3 STEP UP-DOWN
CONVERTER DRIVER
29 NC M1
VC
1
2 3 4 5 6 7
8
9 10
11 12 13 14 15 16
17
18
19 20
21 22
23
24 25 26 27
28
NC_A1
DW 1B
DW 1T
VRECO 2
VRECO 1
L1 2
L1 1
INP1
UP 1T
UP 1B
GND
PGND1
VC
VC
PGND3
PGND1
UP 3B
VREF IN
PGND3
PGND3
V3C 1
V3C 2
33USEL
L3 1
L3 2
DW 3T
DW 3B
V3FB
V3FB
IC602 R1160N121B-TR-FA
VDD 1
GND 2
CE 3
38
REGULATOR
5
VOUT
4
ECO
CURRENT
LIMIT
MZ-NH1
VC LOW
VOLTAGE
DETECTOR
3PHASE
CONTROL
CH1
VI1 1
WI1 2
CPWO2B
CPVO2B
CPUO2B
PWM2
UI2
50
49
48
47 46 45
44 43
VC
VG
VC
OE
51
GND
54 53 52
VC
CPUO1
CPVO1
CPWO1
56 55
VG
UI1
PWM1
IC701 SC901583EPR2
VC
BIAS
3PHASE
CONTROL
CH2
ROE
42 VI2
41 WI2
GNDW1 3
40 GNDW2
VG
WO1
VMVW1
VO1
GNDUV1
VC
VC
3PHASE
PRE DRIVER
CH1
4
5
6
7
VG
3PHASE
PRE DRIVER
CH2
39
38
37
36
UO1 8
WO2
VMVW2
VO2
GNDUV2
35 UO2
VMU1 9
34 VMU2
VC
VG
VMR1 10
RO1 11
PGND1 12
VC
H-BRIDGE
PRE DRIVER
CH1
VG
33 VMR2
32 RO2
31 PGND2
H-BRIDGE
PRE DRIVER
CH2
FO1 13
30 FO2
VMF1 14
29 VMF2
VG VC
VC VG
VC VG
19
20
21
CPVI1
CPWI1
ZI1
HI-BRIDGE
CONTROL
CH2
22
23
24
25 26
27
28
FI2
17 18
VC
–
U
+
RI2
16
VC VG
–
V
+
CPUI2
COM2
15
COM1
CPUI1
–
W
+
RI1
–
W
+
FI1
H-BRIDGE
CONTROL
CH1
VG VC
–
V
+
CPVI2
–
U
+
CPWI2
VG VC
ZI2
VC
CE
VSS
CIN
IC871 R2061K01-E2
12
11
10
9 /INTR
LEVEL
SHIFTER
SIO 1
SCLK 2
REAL
TIME
CLOCK
/VDCC 3
8 OSCOUT
VOLTAGE
REFERENCE
7 OSCIN
DELAY
BATTERY
VOLTAGE
MONITOR
4
5 6
VSB
VCC
VDD
VOLTAGE
DETECTOR
39
MZ-NH1
NC
NC
NC
NC
NC
IC891 AK6514CN-L
20
19
18
17
16
15 VCC
CS 1
14 HOLD
VREF
INSTRUCTION
DECODE
CONTROL
&
CLOCK
GENERATION
SO 2
NC 3
WP 4
VPP
GENERATOR
STATUS
REGISTER
VPP SW
ADD
BUFFERS
13 NC
DECODER
GND 5
R/W AMPS
&
AUTO ERASE
INSTRUCTION
REGISTER
EEPROM
128K bit
16384 × 8
DATA
REGISTER
40
6
7
8
9
10
NC
NC
NC
NC
NC
12 SCK
11 SI
MZ-NH1
REGI3
REGO3
REGC3
MUTEON
DW 2B
DW 2T
VC2
VCIN
VCO2
VO2
L2
L2
PGND2
PGND2
XRST2
CRST2
IC901 SC901584EPR2
48
47
46
45
44 43
42
41
40
39
38 37 36 35
34
33
RESET 2
SERIAL
PASS
REGULATOR 3
POWER
SWITCH 2
REGC2 49
REG2G 50
REGO2 51
REGI2 52
RST2
VC2
STEP
UP-DOWN
DRIVER
RST2
VC2
MUTING
BUFFER
SERIAL
PASS
REGULATOR 2
REF2
VREF
PWM
32 DTC2
REGC1 53
VREF
RST1
REF2
31 RF2
MUTE ON
REGI1 55
SERIAL
PASS
REGULATOR 1
SEQSEL
REGO1 54
RST2
30 INM2
29 VGSEL1
28 VGSEL2
VB
27 VB
VG SELECT, VG DUTY
VREF0
GND 56
26 PGND3
VC
BANDGAP
REFERENCE
VREF 57
25 LG
24 VG
STEP UP
DC/DC CONVERTER
START UP
CLK
23 C1L
REF1
REF2
REF3
REF4
REF5
REF1
22 INM1
VC
VREF0
21 RF1
VREF
REF DAC
20 DTC1
RST1
RST1
LVB
DRIVER
58
59
60
61
62
63
64
PWM
CONTROL
RST2
VC
10
11
12
13 14 15 16
L1
L1
PGND1
PGND1
LVB
9
VO1
VRMC
8
VCO1
FFCLR
XWK4
XWK3
XWK2
XWK1
RESET 1
17 XRST1
POWER
SWITCH 1
VC1
7
VREF
VTSB
6
STEP
UP-DOWN
DRIVER
HVB
1 2 3 4 5
19 XRST1ADJ
18 CRST1
REF1
VC
VC
VREF
FFCLR
DATA
STRB
CLK
WDT
SEQSEL
CLK
SLEEP
IC902 XC62HR5502MR
NC 1
VIN 2
5 VOUT
CURRENT
LIMIT
+
–
CE 3
OUTPUT
CONTROL
REFERENCE
VOLTAGE
4 VSS
41
MZ-NH1
• IC Pin Function Description
IC801 CXD2681-222GG (SYSTEM CONTROLLER, DIGITAL SIGNAL PROCESSOR)
Pin No.
Pin Name
I/O
1
DVDD1_0
—
Power supply terminal
2
DVSS1_0
—
Ground terminal
3
DVDD1_1
—
Power supply terminal
4
DVSS1_1
—
Ground terminal
5
DVDD1_2
—
Power supply terminal
6
DVSS1_2
—
Ground terminal
7
DVDD1_3
—
Power supply terminal
8
DVSS1_3
—
Ground terminal
42
Description
9
DVDD1_4
—
Power supply terminal
10
DVSS1_4
—
Ground terminal
11
DVDD1_5
—
Power supply terminal
12
DVSS1_5
—
Ground terminal
13
DVDD1_6
—
Power supply terminal
14
DVSS1_6
—
Ground terminal
15
DVDD1_7
—
Power supply terminal
16
DVSS1_7
—
Ground terminal
17
DVDD1_8
—
Power supply terminal
18
DVSS1_8
—
Ground terminal
19
DVDD1_9
—
Power supply terminal
20
DVSS1_9
—
Ground terminal
21
DVDD3
—
Power supply terminal
22
VSS_3
—
Ground terminal
23
DVDD1_10
—
Power supply terminal
24
DVSS1_10
—
Ground terminal
25
DVDD1_11
—
Power supply terminal
26
DVSS1_11
—
Ground terminal
27
AVDD1A
—
Power supply terminal (for PLL)
28
AVSS1A
—
Ground terminal (for PLL)
29
AVDD1B
—
Power supply terminal
30
AVSS1B
—
Ground terminal
31
AVDD1C
—
Power supply terminal
32
AVDD2
—
Power supply terminal (for A/D converter)
33
DVDD25SVADC
—
Power supply terminal (for A/D converter)
34
AVSS2
—
Ground terminal (for A/D converter)
35
AVDD3
—
Power supply terminal (for A/D converter)
36
AVSS3
—
Ground terminal (for A/D converter)
37
AVDD4A
—
Power supply terminal (for PLL)
38
AVSS4A
—
Ground terminal (for PLL)
39
AVDD4B
—
Power supply terminal (for PLL)
40
AVSS4B
—
Ground terminal (for PLL)
41
AVDD4C
—
Power supply terminal (for D/A converter)
42
AVSS4C
—
Ground terminal (for D/A converter)
43
AVDD5
—
Power supply terminal (for PLL)
44
AVSS5
—
Ground terminal (for PLL)
45
AVDD6
—
Power supply terminal (for A/D converter)
46
AVSS6
—
Ground terminal (for A/D converter)
MZ-NH1
Pin No.
Pin Name
I/O
Description
47
DAVDD
—
Power supply terminal (for D/A converter)
48
DVDD25LPF
—
Power supply terminal (for D/A converter)
49
DAVSS
—
Ground terminal (for D/A converter)
50
OSCVDD
—
Power supply terminal (for 22 MHz OSC)
51
USBOSCVDD
—
Power supply terminal (for the USB 48 MHz OSC)
52
TSMVDD
—
Power supply terminal (for the TSB master communication)
53
MAIFVDD
—
Power supply terminal (for MA interface)
54
MSJTAGVDD
—
Power supply terminal (for AUX)
55
USBIFVDD
—
Power supply terminal (for USB interface)
56 to 58
VSS_0 to VSS_2
—
Ground terminal
59 to 62
IFVDD_1 to
IFVDD_4
—
Power supply terminal (for interface)
63
IFVSS_1
—
Ground terminal (for interface)
64
IFVSS_2
—
Ground terminal (for interface)
65 to 69
DRAMVDD0 to
DRAMVDD4
—
Power supply terminal (for D-RAM/DSP interface)
70 to 72
DRAMVSS0 to
DRAMVSS2
—
Ground terminal (for D-RAM/DSP interface)
73
FCRAMVDD0
—
Power supply terminal (for D-RAM)
74
FCRAMVSS0
—
Ground terminal (for D-RAM)
75
FCRAMVDD1
—
Power supply terminal (for D-RAM)
76
FCRAMVSS1
—
Ground terminal (for D-RAM)
77
FVDD0
—
Power supply terminal (for AUX)
78
FVSS0
—
Ground terminal (for AUX)
79
SRAMVDD0
—
Power supply terminal (for AUX)
80
SRAMVSS0
—
Ground terminal (for AUX)
81
SRAMVDD1
—
Power supply terminal (for AUX)
82
SRAMVSS1
—
Ground terminal (for AUX)
83
EBIFVDD0
—
Power supply terminal (for interface circuit)
84
EBIFVSS0
—
Ground terminal (for interface circuit)
85
EBIFVDD1
—
Power supply terminal (for interface circuit)
86
EBIFVSS1
—
Ground terminal (for interface circuit)
87
EBIFVDD2
—
Power supply terminal (for interface circuit)
88
EBIFVSS2
—
Ground terminal (for interface circuit)
89
EBIFVDD3
—
Power supply terminal (for interface circuit)
90
EBIFVSS3
—
Ground terminal (for interface circuit)
91
EBIFVDD4
—
Power supply terminal (for interface circuit)
92
EBIFVSS4
—
Ground terminal (for interface circuit)
93
EBIFVDD5
—
Power supply terminal (for interface circuit)
94
EBIFVSS5
—
Ground terminal (for interface circuit)
95
EBIFVDD6
—
Power supply terminal (for interface circuit)
96
EBIFVSS6
—
Ground terminal (for interface circuit)
97
EBIFVDD7
—
Power supply terminal (for interface circuit)
98
EBIFVSS7
—
Ground terminal (for interface circuit)
99
ASYO
O
Playback EFM duplex signal output
100
ASYI
I
Playback EFM comparator slice level input
101
RFI
I
Playback EFM RF signal input from the RF amplifier
43
MZ-NH1
Pin No.
Pin Name
I/O
102
PCO
O
Phase comparison output terminal for the playback EFM system master PLL
44
Description
103
FILI
I
Filter input terminal for the playback EFM system master PLL
104
FILO
O
Filter output terminal for the playback EFM system master PLL
105
CLTV
I
Internal VCO control voltage input terminal for the playback EFM system master PLL
106
PEAK
I
Peak hold signal input of the light amount signal (RF/ABCD) the RF amplifier
107
BOTM
I
Bottom hold signal input of the light amount signal (RF/ABCD) the RF amplifier
108
ABCD
I
Light amount signal (ABCD) input from the RF amplifier
109
FE
I
Focus error signal input from the RF amplifier
110
VC
I
Middle point voltage input from the RF amplifier
111
ADIO
O
Monitor output terminal of A/D converter input signal
112
ADRB
I
A/D converter the lower limit voltage input terminal
113
SE
I
Sled error signal input from the RF amplifier
114
TE
I
Tracking error signal input from the RF amplifier
115
AUX1
I
Auxiliary A/D input terminal
116
ADRT
I
The upper limit voltage of A/D converter input terminal
117
DCHG
—
Not used
Not used
Connecting terminal with the analog power supply of low impedance
118
APC
I
119
ADC1EXTC
—
Error signal input for the laser automatic power control
120
D_VREGO
I
Voltage sensibility of regulator from the headphone amplifier
121
VB_MON
I
Unregulated power supply voltage monitoring terminal
122
CHG_MON
I
Charge or discharge current monitoring terminal
123
VREF_MON
I
Reference voltage input terminal
124
SET_KEY_1
I
Front panel key input terminal
125
SET_KEY_2
I
Front panel key input terminal
126
DCIN_DET
I
DC input voltage for battery charge monitoring terminal
127
HIDC_MON
I
High DC voltage monitoring terminal
128
WK_DET
I
Panel key input for wake-up
129
VBUS_MON
I
USB power supply voltage monitoring terminal
130
BATT_MINUS
_MON
I
Voltage monitoring terminal for the minus terminal of rechargeable battery
131
RMC_KEY
I
Remote commander key input terminal
132
RST_CONT
O
System reset signal output to the power control IC
133
REC_KEY
/DOWNLOAD
I
REC key input terminal
134
RADIO_ON
I
Radio on detection input from the remote commander jack
135
HALF_LOCK_
SW /OPEN_SW
I
Front panel open switch detection terminal
136
XRST
I
System reset signal input from the power control IC
Connection terminal for an external capacitor
137
PLL2EXTCI
I
Connection terminal for an external capacitor
138
PLL2EXTCO
O
Connection terminal for an external capacitor
139
PLL3EXTCI
I
Connection terminal for an external capacitor
140
PLL3EXTCO
O
Connection terminal for an external capacitor
141
DACVREFH
I
Reference voltage input terminal
142
APCREF_DA
O
Reference voltage output terminal
143
ADC3VREFH
I
Reference voltage input terminal
144
ADC3EXTC
—
145
VIN
I
Connection terminal for an external capacitor
RF signal input from the RF amplifier
Not used
MZ-NH1
Pin No.
Pin Name
I/O
146
VREFL
I
Description
Reference voltage terminal connected to the capacitor (for the built-in D/A converter L-CH)
147
AOUTL
O
Built-in D/A converter L-CH signal output
148
AOUTR
O
Built-in D/A converter R-CH signal output
149
VREFR
I
Reference voltage terminal connected to the capacitor (for the built-in D/A converter R-CH)
150
DCLSOUTR
O
PWM modulator signal output to the headphone amplifier (R-CH)
151
DCLSOUTL
O
PWM modulator signal output to the headphone amplifier (L-CH)
152
RTCK
—
Not used
153
ADFG
I
ADIP duplex FM signal (22.05±1kHz) input from the RF amplifier
154
TRDR
O
Tracking servo drive PWM signal output (–) to the coil driver
155
TFDR
O
Tracking servo drive PWM signal output (+) to the coil driver
156
FFDR
O
Focus servo drive PWM signal output (+) to the coil driver
157
FRDR
O
Focus servo drive PWM signal output (–) to the coil driver
158
FS4
O
176.4 kHz clock signal output
159
SFDR
O
Sled servo drive PWM signal output to the motor driver
160
SPRD
O
Spindle motor drive control signal output (U) to the motor driver
161
SPFD
O
Spindle servo drive PWM signal output to the motor driver
162
SPDV
O
Spindle motor drive control signal output (V) to the motor driver
163
SPDW
O
Spindle motor drive control signal output (W) to the motor driver
164
SPCU
I
Spindle motor drive comparison signal input (U) from the motor driver
165
SPCV
I
Spindle motor drive comparison signal input (V) from the motor driver
166
SPCW
I
Spindle motor drive comparison signal input (W) from the motor driver
167
SLDV
O
Sled motor drive control signal output (V) to the motor driver
168
SLDW
O
Sled motor drive control signal output (W) to the motor driver
169
SLCU
I
Sled motor drive comparison signal input (U) from the motor driver
170
SLCV
I
Sled motor drive comparison signal input (V) from the motor driver
171
SLCW
I
Sled motor drive comparison signal input (W) from the motor driver
172
SRDR
O
Sled motor drive control signal output (U) to the motor driver
173
DIN
I
Digital audio signal input terminal
174
FS256_OUT
O
11.2896 MHz clock output
175
CHOPPERCLK
O
Clock signal output for chopper
176 to 179 MNT0 to MNT3
O
Monitor output for DSP
180
OFTRK
I/O
Tracking signal input/output for MD3
181
RECP
O
Laser power changeover signal output
182
EFMO
O
EFM encode data output for the record
183
PAUSE_KEY
I
Pause key input terminal
184
PROTECT
I
Recording protector detection input for normal disc
185
OPT_DET
I
Optical digital input plug detection input terminal
186
XJACK_DET
I
Line input plug detection input terminal
187
XMIC_DET
I
Microphone input plug detection input terminal
188
OPEN_CLOSE
_SW
I
Open switch input terminal
189
XCS_ADC
O
Chip select signal output for A/D converter
190
XPD_ADC
O
Power control signal output for A/D converter
191
NC
—
Not used
192
XRST_LCD
O
Reset signal output for the LCD module
193
USB_WAKE
O
System wake up signal output by USB connect
“H”: optical in
“L”: plug in
“L”: plug in
45
MZ-NH1
Pin No.
Pin Name
I/O
194
A7CAL_SW
O
A7 offset voltage CAL on/off control signal output terminal
46
Description
195
SI0
I
Serial data input from the EEPROM and real time clock IC
196
SO0
O
Serial data output to the EEPROM, real time clock IC, A/D converter and power controller
197
SCK0
O
Serial clock output to the EEPROM, real time clock IC, A/D converter and power controller
198
XGUM_ON
I
Rechargeable battery detection switch input terminal
199
BEEP
O
Beep sound control signal output to the headphone amplifier
200
XOPT_CTL
O
Power supply on/off control signal output for the optical input jack
201
LAM_REQCHK
I
LAM power check terminal
202
LAM_SPREQ
O
LAM force stop request signal output
203
REC_LED
/ACCESS_LED
O
REC LED drive signal output terminal
204
MDVCC_CTL
O
Power supply control signal output for the OP modulation
205
VBUS_VB_CTL
O
USB power supply control signal output terminal
206
LAM_NAME
O
LAM name data request signal output terminal
207
DRAM_ALONE
O
Self-refresh signal output for internal D-RAM
208
XRST_CHG_IC
O
Reset signal output to the charge controller
209
PD_S0
O
Connect to the optical pick-up block
210
PD_S1
O
Connect to the optical pick-up block
211
D_ENREG
O
Enable signal output to the headphone amplifier
212
XMUTE
/MUTE
O
Muting on/off control signal output terminal
213
SI1
I
Serial data input from the LCD module
214
SO1
O
Serial data output to the LCD module
215
SCK1
I/O
216
SLD_MON
I
Sled servo monitoring terminal
217
AOUT_SEL
O
Headphone/line output switching terminal
218
SLEEP
O
Chip enable output to the power control IC
219
FFCLR
O
Power on/off control signal output for FCRAM (internal RAM)
220
CHGI_CTL1
O
Charge current limiter control signal output at the time of AC adaptor use
“L”: limit off, “H”: limit on
221
CHGI_CTL2
O
Charge current control signal output terminal
“L”: low current charge
222
CHGI_CTL3
O
Charge current control signal output terminal
“L”: low current charge
223
SLBUSY
I
Receive signal monitoring terminal for sled command
Not used
Not used
Not used
Not used
Serial data transfer clock signal input/output terminal with the LCD module
Not used
224
XTEST
I
Terminal for the test mode setting (normally open)
225
XRF_RST
O
Reset signal output to the RF amplifier
“L”: test mode
226
VREC_SEL
O
VREC start-up timing control signal output terminal
227
XHOLD_SW
I
HOLD switch input terminal
228
T_MARK_SW
I
Track mark switch input terminal
229
XRST2_DET
I
Reset signal input from the power control IC
230
CHGI_SEL
O
Charge/discharge control signal output for current sense amplifier
231
RECP_MON
I
Laser power changeover signal monitoring terminal
232
SPDL_MON
I
Spindle servo monitoring terminal
233
XCS_PWR_IC
O
Chip select signal output to the power control IC
234
RXD
I
Not used
235
TXD
O
Not used
236
XCS_LCD
O
Chip select signal output to the LCD module
237
N1_VI_CTL
O
Constant current circuit control signal output terminal
Not used
Not used
MZ-NH1
Pin No.
Pin Name
I/O
Description
238
XRST_MTR
_DRV
O
Reset signal output to the motor driver
239
XCS_NV
O
Chip select signal output to the EEPROM
240
CHG_PWM
O
Charge current or voltage control signal output terminal
241
IAMP_CAL
O
Offset signal output of current sense amplifier
242
NC
—
Not used
243
D_VCONT
_PWM
O
For voltage control signal output to the headphone amplifier
244
CHG_OPR_LED
O
Charge indication LED drive signal output terminal
245
XCS_REC_DRV
O
Chip select signal output to the over write head driver
246
GND_SW
O
Ground line switching signal output terminal Not used
247
CS_RTC
O
Chip select signal output for real time clock
248
JOG_A
I
Jog dial pulse input terminal Not used
249
JOG_B
I
Jog dial pulse input terminal Not used
250
VBUS_DET
I
USB power supply voltage detection terminal
251
SSB_DATA
I/O
SSB data input/output with the RF amplifier
252
SSB_CLK
O
SSB clock output to the RF amplifier
253
HIMD_
PROTECT
I
Recording protector detection input for Hi-MD disc
254
LDPEN
O
Pulse/DC light-emit switching signal output terminal
255
CHG_TYPE2
O
Battery charge control signal output terminal “H”: charging Not used
256
DRAM_HOLD
_DET
I
Detection terminal for internal D-RAM power supply information keeping
257
DRAM_VDD
_CLR
O
Internal D-RAM power latch clear signal output for quick mode sleep
258
AD2ENDF
I
Monitoring terminal for flag of servo signal A/D measuring finish
259
TEST
—
260
SRAM_MODE
I
Not used
261
HSALF
I
Not used
262 to
271
TIGER_MON0 to
TIGER_MON9
O
Trigger monitoring terminal output clock=18.5 MHz
272
XLSRCK
O
Pulse output for laser strobe recording
273
TAT
—
Not used
274
TAN
—
Not used
275
NAR
—
Not used
276
IDO
—
Not used
277
SAK
—
Not used
278
LRCKI
I
L/R sampling clock signal input terminal for PCM data interface Not used
279
XBCKI
I
Bit clock signal input terminal for the PCM data interface Not used
280
DATAI
I
Serial clock signal input terminal for the PCM data interface Not used
Not used
281
SI3
I
Serial data input for LAM microcomputer communication Not used
282
SO3
O
Serial data output for LAM microcomputer communication Not used
283
SCK3
O
Serial data transfer clock signal output for LAM microcomputer communication Not used
284
SI4
I
Data input from ATRAC3 plus encoder communication Not used
285
SO4
O
Data output for ATRAC3 plus encoder communication Not used
286
SCK4
O
Clock signal output for ATRAC3 plus encoder communication Not used
287
SCS3
O
Chip select signal output for LAM microcomputer communication Not used
47
MZ-NH1
Pin No.
Pin Name
I/O
288
SCS4
O
Chip select signal output for ATRAC3 plus encoder communication
289
HI_Z_SLD
O
Standby signal output terminal for the sled motor
290
HI_Z_SPDL
O
Standby signal output terminal for the spindle motor
291 to
294
SET_CODE0 to
SET_CODE3
I
Setting terminal for the destination
295, 296 D_EN1, D_EN2
O
Headphone/LINE/beep switching signal output to the headphone amplifier
D_ENVG
O
Power on/off control signal output for headphone amplifier
298
DADT
O
Audio data output terminal
299
PWM_L1
O
LC drive PWM output terminal
300
PWM_L2
O
LC drive PWM output terminal
301
I2C_1
—
Open drain for IIC
302
I2C_2
—
Open drain for IIC
303, 304
TEST
—
Not used
305
CLKIN2
I
Clock signal input terminal (13.5 MHz or 27 MHz)
306
FS256
O
Master clock signal (256Fs=11.2896 MHz) output to A/D converter
307
ADDT
I
Data input from A/D converter
308
LRCK
O
L/R sampling clock signal (44.1kHz) output to external A/D converter
309
XBCK
O
Bit clock (2.8224 MHz) output to the external A/D converter
310
OSCI
I
Main system clock input terminal (22.5792 MHz)
311
OSCO
O
Main system clock output terminal (22.5792 MHz)
312
FS512
O
Clock signal output to the headphone amplifier
313
DTCK
I/O
TSB master data clock input/output or SSB data input/output
314
UDP
I/O
USB data (+) input/output terminal
315
UDM
I/O
USB data (–) input/output terminal
316
USBHOLD
I
USB hold signal input terminal
317
SUSPEND
O
USB suspend signal output
318
UPUEN
O
USB pull-up resistor connection control output terminal
319
UOSCI
I
Resonator (48MHz) connection terminal for the USB oscillation circuit
320
UOSCO
O
Resonator (48MHz) connection terminal for the USB oscillation circuit
321 to 325
NC
—
Not used
297
48
Description
Not used
Not used
Not used
MZ-NH1
SECTION 7
EXPLODED VIEWS
NOTE:
• Items marked “*” are not stocked since they
• -XX and -X mean standardized parts, so they
are seldom required for routine service. Some
may have some difference from the original
delay should be anticipated when ordering
one.
these items.
• Color Indication of Appearance Parts
• The mechanical parts with no reference
Example:
number in the exploded views are not supplied.
KNOB, BALANCE (WHITE) . . . (RED)
• Accessories are given in the last of the
↑
↑
electrical parts list.
Parts Color Cabinet's Color
• Abbreviation
• Color Variation
JE : Tourist model
CH : Chinese model
Silver : All models
KR : Korea model
E18 : 100 V - 240 V AC Area in E model
Gold : HK, KR, CH, E18, JE models
HK : Hong Kong model
7-1.
PANEL SECTION
8
7
6
16
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
3
not supplied
3
17
not
supplied
12
9
13
10
15
5
14
11
4
3
3
2
main section
1
Ref. No.
Part No.
Description
1
1
2
3
4
3-264-157-01
3-264-157-31
3-264-158-01
3-225-873-09
X-2023-574-1
KNOB (HOLD) (SILVER)
KNOB (HOLD) (GOLD)
KNOB (OPEN)
SCREW (M1.4)
PANEL (S-CE) SUB ASSY, BOTTOM (SILVER)
(AEP, UK)
4
X-2023-575-1 PANEL (S-NONCE)SUB ASSY,BOTTOM (SILVER)
(EXCEPT AEP, UK)
X-2023-576-1 PANEL (N-NONCE)SUB ASSY,BOTTOM (GOLD)
(HK, KR, CH, E18, JE)
3-264-156-01 ESCUTCHEON (CONNECTOR) (SILVER)
3-264-156-41 ESCUTCHEON (CONNECTOR) (GOLD)
2-050-812-02 SHEET (LOWER PANEL)
4
5
5
6
Remark
Ref. No.
Part No.
Description
Remark
7
8
8
9
10
3-264-154-11
X-2021-801-1
X-2021-802-1
3-225-873-29
1-805-493-11
BADGE (HI-MD)
PANEL (S) SUB ASSY, UPPER (SILVER)
PANEL (N) SUB ASSY, UPPER (GOLD)
SCREW (M1.4)
LCD MODULE
11
12
13
14
15
3-254-003-01
3-264-153-01
2-189-608-01
2-186-565-01
2-177-997-01
SCREW
SPRING (REC), COMPRESSION
SHEET (LCD MODULE), INSULATING
SHEET (EMC LOWER B), ADHESIVE
SHEET (EMC LOWER)
16
17
2-024-015-01 SPACER (HP)
2-067-920-01 SPACER (COIL)
49
MZ-NH1
7-2.
MAIN SECTION
62
mechanism deck section
56
60
59
64
63
55
54
70
not
supplied
53
65
81
69
82
77
84
79
57
83
78
76
58
85
80
61
75
72
71
MAIN board
74
68
73
51
87
67
88
51
52
86
Ref. No.
51
52
Part No.
Description
Remark
53
3-238-876-07 SCREW (M1.4), TOOTHED LOCK
X-2023-571-1 MAIN BOARD, COMPLETE (for SERVICE)
(E18, JE)
X-2024-720-1 MAIN BOARD, COMPLETE (for SERVICE) (US)
X-2024-721-1 MAIN BOARD, COMPLETE (for SERVICE)
(EXCEPT US, E18, JE)
3-264-138-01 TERMINAL, BATTERY
54
55
56
57
58
3-264-137-01
3-264-139-01
3-264-140-01
3-264-131-01
3-264-132-01
HOLDER, TERMINAL
SPRING (BATT)
CASE, BATTERY
SPRING (OPEN)
SPRING (LIMITER)
59
60
61
62
63
X-3384-755-2
3-264-136-01
3-264-135-01
3-246-996-01
3-254-003-01
CHASSIS ASSY, SET
SPRING (POP-L)
SPRING (POP-R)
SCREW (MD), STEP
SCREW
64
65
67
68
1-478-469-11
3-264-144-01
3-264-161-01
3-234-449-25
SWITCH UNIT
BUTTON CONTROL (5 DIRECTION) (B ENT)
LID, BATTERY CASE
SCREW (M1.4)
52
52
50
Ref. No.
Part No.
Description
69
70
71
72
73
2-190-061-01
2-178-887-01
X-2024-190-1
2-176-415-01
2-176-392-01
SPACER (MIC-LINE)
SPACER (HEAD FLEXIBLE)
ORNAMENT SUB ASSY, CONTROL
SPRING (EMC) (2), LEAF
SPACER (RECEPTACLE)
74
75
76
77
78
2-176-414-01
2-067-920-01
2-024-013-01
2-024-015-01
2-108-116-01
SPRING (EMC) (1), LEAF
SPACER (COIL)
SPACER (LINE IN)
SPACER (HP)
COVER (RECEPTACLE)
79
80
81
82
83
2-024-014-01
3-266-842-01
2-067-464-01
2-190-444-01
3-264-143-01
SPACER (MIC)
SPACER (SLED MOTOR)
SPACER (MIC) 2
SPACER (HP) 2
CONTROL, BUTTON (SIDE)
84
85
86
87
88
2-178-130-01
2-178-129-01
2-178-128-01
2-159-395-01
2-178-259-01
SHEET (SHEILD C)
SHEET (SHEILD B)
SHEET (SHEILD A)
SPACER (IC)
SHEET (LEAF SPRING), INSULATING
Remark
MZ-NH1
7-3.
MECHANISM DECK SECTION
159
not supplied
164
163
158
(including HR601
(over write head) )
161
not supplied HR601
(over write head)
157
154
M702
160
162
156
154
M703
M701
153
155
153
152
153
151
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
Description
151
152
153
154
155
3-338-645-31
3-244-882-02
3-248-370-01
3-225-996-17
3-244-880-01
WASHER (0.8-2.5)
GEAR (SA)
SCREW, SELF TAP
SCREW (M1.4) (EG), PRECISION PAN
SPRING, THRUST RETAINER
156
157
158
159
160
3-244-883-02
3-259-972-12
X-3382-398-3
X-3384-181-2
3-245-021-03
GEAR (SB)
CHASSIS (REC)
BASE ASSY, MOTOR
HOLDER ASSY
PLATE, RATCHET
Remark
Ref. No.
Part No.
161
162
0 163
X-2023-012-1 SCREW SERVICE ASSY, LEAD
3-244-879-01 SPRING, RACK
X-2021-779-1 SERVICE ASSY, OP (ABX-U)
(including HR601 (OVER WRITE HEAD))
3-259-981-01 SPRING (EJECT), TENSION
8-835-782-02 MOTOR, DC SSM18D/C-NP (SPINDLE)
164
M701
M702
M703
Description
Remark
8-835-778-11 MOTOR, DC SSM21A/C-NP (SLED)
1-477-519-21 MOTOR UNIT, DC
(OVER WRITE HEAD UP/DOWN)
51
MZ-NH1
SECTION 8
ELECTRICAL PARTS LIST
MAIN
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
• Abbreviation
CH : Chinese model
E18 : 100 V - 240 V AC Area in E model
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA... : µA...
uPA... : µPA...
uPB... : µPB...
uPC... : µPC...
uPD... : µPD...
• CAPACITORS
uF: µF
• COILS
uH: µH
HK : Hong Kong model
JE : Tourist model
KR : Korea model
Description
Remark
X-2023-571-1 MAIN BOARD, COMPLETE (for SERVICE)
(E18, JE)
X-2024-720-1 MAIN BOARD, COMPLETE (for SERVICE) (US)
X-2024-721-1 MAIN BOARD, COMPLETE (for SERVICE)
(EXCEPT US, E18, JE)
*********************
2-024-013-01
2-024-014-01
2-024-015-01
2-067-464-01
2-067-920-01
SPACER (LINE IN)
SPACER (MIC)
SPACER (HP)
SPACER (MIC) 2
SPACER (COIL)
2-108-116-01
2-159-395-01
2-176-392-01
2-190-061-01
2-178-128-01
COVER (RECEPTACLE)
SPACER (IC)
SPACER (RECEPTACLE)
SPACER (MIC-LINE)
SHEET (SHIELD A)
2-178-129-01
2-178-130-01
2-178-259-01
2-190-444-01
3-266-842-01
SHEET (SHIELD B)
SHEET (SHIELD C)
SHEET (LEAF SPRING), INSULATING
SPACER (HP) 2
SPACER (SLED MOTOR)
< CAPACITOR >
C101
C102
C104
C105
C106
1-164-874-11
1-125-837-11
1-164-939-11
1-125-777-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
1uF
0.0022uF
0.1uF
0.001uF
5%
10%
10%
10%
10%
50V
6.3V
50V
10V
50V
C107
C108
C151
C152
C153
1-100-843-11
1-125-926-11
1-125-777-11
1-164-937-11
1-127-715-11
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
4.7uF
0.1uF
0.001uF
0.22uF
20%
20%
10%
10%
10%
4V
6.3V
10V
50V
16V
C154
C155
C201
C202
C204
1-135-868-11
1-125-777-11
1-164-874-11
1-125-837-11
1-164-939-11
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220uF
0.1uF
100PF
1uF
0.0022uF
20%
10%
5%
10%
10%
2.5V
10V
50V
6.3V
50V
C205
C206
C207
C208
C251
1-125-777-11
1-164-937-11
1-100-843-11
1-125-926-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
0.1uF
0.001uF
47uF
4.7uF
0.1uF
10%
10%
20%
20%
10%
10V
50V
4V
6.3V
10V
C252
1-164-937-11 CERAMIC CHIP
0.001uF
10%
50V
52
Ref. No.
The components identified by mark
0 or dotted line with mark 0 are
critical for safety.
Replace only with part number
specified.
When indicating parts by reference
number, please include the board.
Part No.
Description
Remark
C253
C254
C255
C302
1-127-715-11
1-135-868-11
1-125-777-11
1-164-939-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
220uF
0.1uF
0.0022uF
10%
20%
10%
10%
16V
2.5V
10V
50V
C303
C304
C305
C306
C307
1-125-777-11
1-164-874-11
1-164-874-11
1-164-939-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
100PF
100PF
0.0022uF
0.001uF
10%
5%
5%
10%
10%
10V
50V
50V
50V
50V
C308
C310
C311
C312
C313
1-164-937-11
1-117-919-11
1-125-777-11
1-100-842-11
1-100-842-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
0.001uF
10uF
0.1uF
47uF
47uF
10%
20%
10%
20%
20%
50V
6.3V
10V
6.3V
6.3V
C314
C315
C316
C318
C319
1-125-777-11
1-117-919-11
1-100-453-11
1-100-840-11
1-125-777-11
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
0.1uF
10uF
22uF
2.2uF
0.1uF
10%
20%
20%
20%
10%
10V
6.3V
6.3V
10V
10V
C320
C321
C322
C323
C324
1-100-840-11
1-100-842-11
1-125-777-11
1-117-919-11
1-125-777-11
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
2.2uF
47uF
0.1uF
10uF
0.1uF
20%
20%
10%
20%
10%
10V
6.3V
10V
6.3V
10V
C325
C327
C328
C351
C352
1-125-777-11
1-125-837-11
1-125-837-11
1-125-891-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
1uF
0.47uF
0.1uF
10%
10%
10%
10%
10%
10V
6.3V
6.3V
10V
10V
C353
C354
C355
C356
C357
1-164-937-11
1-165-884-11
1-112-011-21
1-100-842-11
1-100-842-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
0.001uF
2.2uF
47uF
47uF
47uF
10%
10%
20%
20%
20%
50V
6.3V
6.3V
6.3V
6.3V
C358
C359
C360
C361
C362
1-100-842-11
1-100-842-11
1-165-884-11
1-100-842-11
1-117-919-11
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
47uF
47uF
2.2uF
47uF
10uF
20%
20%
10%
20%
20%
6.3V
6.3V
6.3V
6.3V
6.3V
C364
C365
C367
C368
C370
1-165-884-11
1-125-837-11
1-125-837-11
1-127-715-11
1-100-352-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2uF
1uF
1uF
0.22uF
1uF
10%
10%
10%
10%
20%
6.3V
6.3V
6.3V
16V
16V
MZ-NH1
MAIN
Ref. No.
Part No.
Description
Remark
C401
C402
C403
C404
C405
1-125-777-11
1-100-844-11
1-100-844-11
1-164-937-11
1-125-777-11
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22uF
22uF
0.001uF
0.1uF
10%
20%
20%
10%
10%
10V
10V
10V
50V
10V
C406
C407
C408
C409
C410
1-125-777-11
1-125-777-11
1-125-777-11
1-164-943-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.01uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
10V
16V
10V
C412
C415
C431
C432
C433
1-107-826-11
1-125-777-11
1-164-939-11
1-164-939-11
1-164-939-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.0022uF
0.0022uF
0.0022uF
10%
10%
10%
10%
10%
16V
10V
50V
50V
50V
C434
C452
C453
C454
C455
1-162-964-11
1-164-939-11
1-164-939-11
1-162-962-11
1-164-939-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.0022uF
0.0022uF
470PF
0.0022uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C456
C457
C460
1-164-939-11 CERAMIC CHIP
1-164-939-11 CERAMIC CHIP
1-100-506-11 CERAMIC CHIP
0.0022uF 10%
0.0022uF 10%
1uF
20%
C460
1-164-935-11 CERAMIC CHIP
470PF
C503
1-164-937-11 CERAMIC CHIP
0.001uF
50V
50V
6.3V
(E18, JE)
10%
50V
(EXCEPT E18, JE)
10%
50V
C511
C513
C515
C516
C517
1-125-777-11
1-164-943-11
1-125-777-11
1-125-777-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
10V
16V
10V
10V
10V
C518
C519
C520
C521
C522
1-125-926-11
1-125-777-11
1-125-777-11
1-164-850-11
1-164-850-11
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4.7uF
0.1uF
0.1uF
10PF
10PF
20%
10%
10%
0.5PF
0.5PF
6.3V
10V
10V
50V
50V
C523
C524
C525
C526
C527
1-125-777-11
1-162-970-11
1-164-941-11
1-164-874-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.0047uF
100PF
0.1uF
10%
10%
10%
5%
10%
10V
25V
16V
50V
10V
C528
C529
C530
C531
C533
1-125-777-11
1-125-777-11
1-125-837-11
1-164-943-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
1uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
10V
10V
6.3V
16V
16V
C536
C537
C538
C539
C545
1-107-819-11
1-125-837-11
1-164-937-11
1-125-837-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
1uF
0.001uF
1uF
0.1uF
10%
10%
10%
10%
10%
16V
6.3V
50V
6.3V
10V
C547
C550
C552
C553
C554
1-119-923-11
1-119-923-11
1-164-943-11
1-125-926-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
0.047uF
0.047uF
0.01uF
4.7uF
0.1uF
10%
10%
10%
20%
10%
10V
10V
16V
6.3V
10V
Ref. No.
Part No.
Description
C555
C556
C557
C558
C559
1-164-941-11
1-125-926-11
1-125-777-11
1-164-937-11
1-164-941-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
4.7uF
0.1uF
0.001uF
0.0047uF
10%
20%
10%
10%
10%
16V
6.3V
10V
50V
16V
Remark
C560
C561
C562
C564
C565
1-125-777-11
1-125-837-11
1-125-837-11
1-131-860-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
0.1uF
1uF
1uF
4.7uF
0.1uF
10%
10%
10%
20%
10%
10V
6.3V
6.3V
10V
10V
C566
C567
C568
C569
C570
1-125-777-11
1-125-926-11
1-164-943-11
1-164-943-11
1-112-014-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
0.1uF
4.7uF
0.01uF
0.01uF
4.7uF
10%
20%
10%
10%
20%
10V
6.3V
16V
16V
6.3V
C573
C574
1-164-937-11 CERAMIC CHIP
1-164-935-11 CERAMIC CHIP
C574
1-164-937-11 CERAMIC CHIP
C575
1-164-937-11 CERAMIC CHIP
C601
C602
1-125-837-11 CERAMIC CHIP
1-125-777-11 CERAMIC CHIP
0.001uF 10%
50V
470PF
10%
50V
(EXCEPT US, E18, JE)
0.001uF 10%
50V
(US, E18, JE)
0.001uF 10%
50V
(US, E18, JE)
1uF
10%
6.3V
0.1uF
10%
10V
C604
C611
C612
C613
C614
1-125-777-11
1-164-943-11
1-100-453-11
1-100-453-11
1-100-453-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
0.1uF
0.01uF
22uF
22uF
22uF
10%
10%
20%
20%
20%
10V
16V
6.3V
6.3V
6.3V
C615
C616
C617
C619
C620
1-100-453-11
1-100-844-11
1-100-453-11
1-125-837-11
1-107-819-11
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
22uF
22uF
1uF
0.022uF
20%
20%
20%
10%
10%
6.3V
10V
6.3V
6.3V
16V
C621
C622
C624
C625
C626
1-117-919-11
1-100-442-11
1-164-933-11
1-125-777-11
1-164-943-11
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
220PF
0.1uF
0.01uF
20%
20%
10%
10%
10%
6.3V
6.3V
50V
10V
16V
C628
C629
C630
C632
C633
1-125-837-11
1-125-777-11
1-125-777-11
1-100-842-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
1uF
0.1uF
0.1uF
47uF
0.01uF
10%
10%
10%
20%
10%
6.3V
10V
10V
6.3V
16V
C634
C635
C636
C637
C638
1-125-837-11
1-100-842-11
1-125-777-11
1-117-919-11
1-164-937-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
1uF
47uF
0.1uF
10uF
0.001uF
10%
20%
10%
20%
10%
6.3V
6.3V
10V
6.3V
50V
C639
C641
C642
C643
C644
1-107-826-11
1-164-943-11
1-107-819-11
1-165-884-11
1-164-941-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.01uF
0.022uF
2.2uF
0.0047uF
10%
10%
10%
10%
10%
16V
16V
16V
6.3V
16V
C645
C646
C647
C648
C649
1-164-943-11
1-119-923-11
1-165-176-11
1-119-923-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.047uF
0.047uF
0.047uF
0.1uF
10%
10%
10%
10%
10%
16V
10V
16V
10V
10V
53
MZ-NH1
MAIN
Ref. No.
Part No.
Description
Remark
C650
C651
C652
C653
C654
1-100-442-11
1-100-353-11
1-104-851-11
1-104-851-11
1-125-777-11
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
10uF
4.7uF
10uF
10uF
0.1uF
20%
10%
20%
20%
10%
6.3V
16V
10V
10V
10V
C655
C656
C658
C659
C660
1-125-837-11
1-125-837-11
1-100-844-11
1-100-353-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
22uF
4.7uF
0.1uF
10%
10%
20%
10%
10%
6.3V
6.3V
10V
16V
10V
C662
C663
C674
C701
C702
1-164-943-11
1-164-937-11
1-112-010-11
1-107-819-11
1-107-819-11
CERAMIC CHIP
CERAMIC CHIP
CAP-CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.001uF
33PF
0.022uF
0.022uF
10%
10%
5%
10%
10%
16V
50V
100V
16V
16V
C703
C705
C706
C707
C708
1-107-819-11
1-164-943-11
1-107-819-11
1-164-943-11
1-107-819-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.01uF
0.022uF
0.01uF
0.022uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C709
C710
C712
C713
C714
1-164-943-11
1-107-819-11
1-125-777-11
1-107-826-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.022uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
10V
16V
10V
C715
C716
C717
C801
C802
1-125-777-11
1-125-777-11
1-125-777-11
1-164-850-11
1-164-850-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
10PF
10PF
10%
10%
10%
0.5PF
0.5PF
10V
10V
10V
50V
50V
C803
C804
C805
C808
C809
1-164-943-11
1-164-943-11
1-125-891-11
1-125-837-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.47uF
1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
10V
6.3V
10V
C810
C811
C812
C813
C814
1-125-777-11
1-125-777-11
1-125-837-11
1-119-923-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
1uF
0.047uF
0.1uF
10%
10%
10%
10%
10%
10V
10V
6.3V
10V
10V
C816
C817
C818
C819
C820
1-100-842-11
1-125-777-11
1-100-842-11
1-100-842-11
1-125-777-11
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
47uF
0.1uF
47uF
47uF
0.1uF
20%
10%
20%
20%
10%
6.3V
10V
6.3V
6.3V
10V
C821
C822
C823
C825
C826
1-164-874-11
1-125-777-11
1-125-777-11
1-164-937-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.1uF
0.1uF
0.001uF
0.001uF
5%
10%
10%
10%
10%
50V
10V
10V
50V
50V
C827
C835
C836
C838
C839
1-125-777-11
1-125-777-11
1-100-442-11
1-100-442-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
0.1uF
0.1uF
10uF
10uF
0.1uF
10%
10%
20%
20%
10%
10V
10V
6.3V
6.3V
10V
C843
C845
1-125-777-11 CERAMIC CHIP
1-125-777-11 CERAMIC CHIP
0.1uF
0.1uF
10%
10%
10V
10V
54
Ref. No.
Part No.
Description
Remark
C847
C849
C851
1-125-777-11 CERAMIC CHIP
1-125-777-11 CERAMIC CHIP
1-125-777-11 CERAMIC CHIP
0.1uF
0.1uF
0.1uF
10%
10%
10%
10V
10V
10V
C852
C855
C856
C861
C871
1-125-777-11
1-125-777-11
1-100-842-11
1-164-858-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
47uF
22PF
0.1uF
10%
10%
20%
5%
10%
10V
10V
6.3V
50V
10V
C873
C874
C877
C878
C879
1-164-842-11
1-100-842-11
1-125-777-11
1-125-777-11
1-100-352-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2PF
47uF
0.1uF
0.1uF
1uF
0.25PF
20%
10%
10%
20%
50V
6.3V
10V
10V
16V
C880
C881
C883
C884
C885
1-100-352-11
1-125-777-11
1-125-837-11
1-164-943-11
1-125-837-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.1uF
1uF
0.01uF
1uF
20%
10%
10%
10%
10%
16V
10V
6.3V
16V
6.3V
C888
C890
C891
C892
C894
1-125-777-11
1-125-777-11
1-125-777-11
1-164-874-11
1-164-937-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
100PF
0.001uF
10%
10V
10%
10V
10%
10V
5%
50V
10%
50V
(US, E18, JE)
C901
C902
C903
C905
C906
1-125-777-11
1-125-777-11
1-164-937-11
1-100-352-11
1-100-352-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.001uF
1uF
1uF
10%
10%
10%
20%
20%
10V
10V
50V
16V
16V
C909
C910
C911
C912
C913
1-100-845-11
1-100-845-11
1-100-845-11
1-100-845-11
1-100-845-11
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
TANTALUM CHIP
10uF
10uF
10uF
10uF
10uF
20%
20%
20%
20%
20%
16V
16V
16V
16V
16V
C914
C916
C917
C918
C919
1-100-442-11
1-100-442-11
1-125-777-11
1-164-227-11
1-164-227-11
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
0.1uF
0.022uF
0.022uF
20%
20%
10%
10%
10%
6.3V
6.3V
10V
25V
25V
C920
C922
C924
C925
C926
1-125-777-11
1-100-453-11
1-100-842-11
1-125-777-11
1-164-937-11
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22uF
47uF
0.1uF
0.001uF
10%
20%
20%
10%
10%
10V
6.3V
6.3V
10V
50V
C927
C928
C929
C931
C932
1-164-874-11
1-164-874-11
1-164-937-11
1-165-884-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
0.001uF
2.2uF
0.01uF
5%
5%
10%
10%
10%
50V
50V
50V
6.3V
16V
C934
C936
C938
C939
C940
1-165-884-11
1-165-884-11
1-165-884-11
1-100-453-11
1-100-453-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
2.2uF
2.2uF
2.2uF
22uF
22uF
10%
10%
10%
20%
20%
6.3V
6.3V
6.3V
6.3V
6.3V
C941
C942
C948
C949
1-100-352-11
1-100-352-11
1-100-453-11
1-100-844-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
1uF
1uF
22uF
22uF
20%
20%
20%
20%
16V
16V
6.3V
10V
MZ-NH1
MAIN
Ref. No.
Part No.
Description
Remark
C951
1-100-841-11 TANTALUM CHIP 100uF
20%
6.3V
C952
C954
C955
C957
1-100-841-11
1-125-777-11
1-100-844-11
1-125-777-11
20%
10%
20%
10%
6.3V
10V
10V
10V
TANTALUM CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
100uF
0.1uF
22uF
0.1uF
< CONNECTOR >
CN451
CN471
CN491
CN501
CN701
1-818-137-21
1-818-537-21
1-818-471-21
1-818-539-21
1-818-536-21
CONNECTOR (CRADLE) (USB)
CONNECTOR, FPC (ZIF) 11P
CONNECTOR, FPC (ZIF) 8P
CONNECTOR, FPC (ZIF) 26P
CONNECTOR, FPC (ZIF) 10P
< DIODE >
Ref. No.
Part No.
Description
Remark
< FUSE >
F351
1-576-439-41 FUSE (SMD)
< FERRITE BEAD/SHORT >
FB101
FB102
FB151
FB201
FB202
1-400-807-21
1-414-594-11
1-400-180-21
1-400-807-21
1-414-594-11
BEAD, FERRITE (1005)
INDUCTOR, FERRITE BEAD
INDUCTOR, EMI FERRITE (1608)
BEAD, FERRITE (1005)
INDUCTOR, FERRITE BEAD
FB251
FB301
FB302
FB303
FB304
1-400-180-21
1-400-807-21
1-414-594-11
1-400-807-21
1-400-807-21
INDUCTOR, EMI FERRITE (1608)
BEAD, FERRITE (1005)
INDUCTOR, FERRITE BEAD
BEAD, FERRITE (1005)
BEAD, FERRITE (1005)
FB351
FB353
FB354
FB355
FB357
1-400-180-21
1-414-594-11
1-414-594-11
1-414-594-11
1-414-594-11
INDUCTOR, EMI FERRITE (1608)
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
D152
D252
D301
D352
D401
8-719-046-91
8-719-046-91
8-719-056-54
8-719-081-71
6-500-369-01
DIODE
DIODE
DIODE
DIODE
DIODE
MA2S111
MA2S111
MAZS068008SO
DF8A6.8FK (TE85R)
FT1J3TP
D431
D451
D455
D456
D457
D491
6-500-483-01
6-500-776-01
8-719-056-54
8-719-056-54
8-719-056-54
8-719-056-54
DIODE
DIODE
DIODE
DIODE
DIODE
DIODE
MA22D2800LS0
MAZW068H0LS0
MAZS068008SO
MAZS068008SO
MAZS068008SO (EXCEPT US, E18, JE)
MAZS068008SO
FB451
FB453
FB454
FB501
FB502
1-469-869-21
1-469-869-21
1-469-869-21
1-400-620-21
1-216-864-11
INDUCTOR (EMI FERRITE) (2012)
INDUCTOR (EMI FERRITE) (2012)
INDUCTOR (EMI FERRITE) (2012)
INDUCTOR, FERRITE BEAD (1005)
SHORT CHIP
0
D501
D601
D602
D603
D604
8-719-056-54
8-719-072-27
6-500-483-01
6-500-483-01
6-500-483-01
DIODE
DIODE
DIODE
DIODE
DIODE
MAZS068008SO
MA2Z748001S0
MA22D2800LS0
MA22D2800LS0
MA22D2800LS0
FB503
FB801
FB802
FB803
FB807
1-216-864-11
1-414-226-21
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
0
INDUCTOR, FERRITE BEAD
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
D605
D606
D607
D608
D609
6-500-910-01
6-500-909-01
6-500-909-01
6-500-910-01
8-719-072-27
DIODE
DIODE
DIODE
DIODE
DIODE
MA2SD3000LS0
MA22D1700LS0
MA22D1700LS0
MA2SD3000LS0
MA2Z748001S0
FB808
FB809
FB810
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
D610
D611
D613
D614
D615
8-719-072-27
6-500-912-01
8-719-072-27
8-719-422-49
6-500-483-01
DIODE
DIODE
DIODE
DIODE
DIODE
MA2Z748001S0
MA2SD3100LS0
MA2Z748001S0
MA8056-L
MA22D2800LS0
IC301
IC302
IC351
IC401
IC501
6-702-894-01
6-706-528-01
6-704-998-01
6-704-638-01
6-705-012-01
IC
IC
IC
IC
IC
AK5356VN-L
XC6219B212MR
CXD9811K (TE4)
MM1655LCBE
SN761059ZQLR
D616
D617
D618
D801
D803
6-500-909-01
6-500-909-01
6-500-912-01
6-500-912-01
6-500-813-01
DIODE
DIODE
DIODE
DIODE
DIODE
MA22D1700LS0
MA22D1700LS0
MA2SD3100LS0
MA2SD3100LS0
MA2SD32008S0
IC502
IC601
IC602
IC603
IC604
6-706-095-01
6-705-000-01
6-703-317-01
6-706-079-01
6-706-214-01
IC
IC
IC
IC
IC
R1180Q301B-TR-FA
SC901585VAR2
R1160N121B-TR-FA
R1180Q121C-TR-FA
TC7SL32FU (TE85R)
D871
D881
D882
D883
D884
6-500-813-01
8-719-072-27
8-719-072-27
8-719-072-27
6-500-483-01
DIODE
DIODE
DIODE
DIODE
DIODE
MA2SD32008S0
MA2Z748001S0
MA2Z748001S0
MA2Z748001S0
MA22D2800LS0
IC605
IC701
IC801
IC804
IC871
6-702-590-01
6-705-001-01
8-753-225-26
6-706-089-01
6-703-012-01
IC
IC
IC
IC
IC
XC61CN1702NR
SC901583EPR2
CXD2681-222GG
XC61CC2502NR
R2061K01-E2
D901
D902
D903
D904
D905
8-719-072-27
8-719-072-27
8-719-072-27
8-719-072-27
8-719-072-27
DIODE
DIODE
DIODE
DIODE
DIODE
MA2Z748001S0
MA2Z748001S0
MA2Z748001S0
MA2Z748001S0
MA2Z748001S0
IC872
IC873
IC881
IC882
IC891
6-706-096-01
6-703-011-01
8-759-664-89
6-706-094-01
(Not supplied)
IC
IC
IC
IC
IC
R1180Q331C-TR-FA
TC7SZ126AFE
XC61CN3102NR
R1180Q221B-TR-FA
AK6514CN-L
D906
8-719-072-27 DIODE MA2Z748001S0
IC901
IC902
IC903
6-704-997-01 IC SC901584EPR2
6-706-090-01 IC XC62HR5502MR
6-704-245-01 IC XC61CC1702NR
0
0
0
< IC >
55
MZ-NH1
MAIN
Ref. No.
Part No.
Description
Remark
< JACK >
J301
J302
J351
1-815-950-12 JACK (LINE IN (OPT))
1-818-135-11 JACK (MIC (PLUG IN POWER))
1-816-153-21 JACK (i/LINE)
< COIL/SHORT >
L152
L252
L303
L501
L502
1-400-582-21
1-400-582-21
1-400-342-21
1-216-296-11
1-469-535-21
INDUCTOR
INDUCTOR
INDUCTOR
SHORT CHIP
INDUCTOR
47uH
47uH
10uH
0
10uH
L503
L504
L505
L506
L507
1-469-535-21
1-469-535-21
1-469-535-21
1-469-535-21
1-216-864-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
SHORT CHIP
10uH
10uH
10uH
10uH
0
L601
L605
L606
L607
L701
1-400-402-21
1-456-711-21
1-400-306-11
1-456-722-21
1-216-296-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
SHORT CHIP
4.7uH
100uH
100uH
100uH
0
L702
L703
L704
L801
L802
1-456-724-21
1-216-296-11
1-456-724-21
1-469-535-21
1-400-343-21
FERRITE
SHORT CHIP
FERRITE
INDUCTOR
INDUCTOR
22uH
0
22uH
10uH
22uH
L803
L804
L870
L901
L902
1-216-797-11
1-216-797-11
1-400-342-21
1-456-725-21
1-456-725-21
METAL CHIP
METAL CHIP
INDUCTOR
INDUCTOR
INDUCTOR
10
10
10uH
100uH
100uH
L903
L904
L906
L907
1-400-342-21
1-400-342-21
1-456-723-21
1-456-723-21
INDUCTOR
INDUCTOR
COIL, CHOKE
COIL, CHOKE
10uH
10uH
220uH
220uH
Part No.
Description
Q603
Q604
Q605
Q606
6-550-671-01
8-729-427-74
6-550-671-01
6-550-354-01
FET
TRANSISTOR
FET
FET
NTHC5513T1G
XP4601
NTHC5513T1G
RTQ035P02TR
Remark
Q607
Q611
Q801
Q802
Q803
8-729-427-74
6-550-353-01
8-729-051-50
8-729-047-68
8-729-037-52
TRANSISTOR
FET
FET
FET
TRANSISTOR
XP4601
SI1410EDH-T1
XP152A12C0MR
SSM3K03FE (TPL3)
2SD2216J-QR (TX).SO
Q881
Q882
Q883
Q884
Q951
8-729-037-75
8-729-030-46
8-729-030-46
6-550-353-01
8-729-427-74
TRANSISTOR
TRANSISTOR
TRANSISTOR
FET
TRANSISTOR
UN9214J-(TX).SO
XP4314-TX
XP4314-TX
SI1410EDH-T1
XP4601
< RESISTOR >
5%
5%
1/10W
1/10W
< LINE FILTER >
LF451
Ref. No.
1-456-111-11 COIL, COMMON MODE CHOKE
R101
R103
R106
R107
R151
1-208-927-11
1-208-715-11
1-208-707-11
1-208-715-11
1-218-957-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
47K
22K
10K
22K
2.2K
0.5%
0.5%
0.5%
0.5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R154
R201
R203
R206
R207
1-218-957-11
1-208-927-11
1-208-715-11
1-208-707-11
1-208-715-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
47K
22K
10K
22K
5%
0.5%
0.5%
0.5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R251
R254
R301
R304
R305
1-218-957-11
1-218-957-11
1-218-953-11
1-218-977-11
1-218-941-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
2.2K
1K
100K
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R306
R307
R308
R309
R310
1-218-965-11
1-218-941-11
1-216-864-11
1-218-953-11
1-218-953-11
RES-CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
10K
100
0
1K
1K
5%
5%
1/16W
1/16W
5%
5%
1/16W
1/16W
R313
R314
R315
R351
R352
1-208-635-11
1-218-990-11
1-218-990-11
1-218-953-11
1-218-973-11
METAL CHIP
SHORT CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
10
0
0
1K
47K
0.5%
1/16W
5%
5%
1/16W
1/16W
R353
R354
R355
R356
R357
1-208-715-11
1-218-990-11
1-218-989-11
1-218-990-11
1-218-990-11
METAL CHIP
SHORT CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
22K
0
1M
0
0
0.5%
1/16W
5%
1/16W
R358
R360
R361
R363
R364
1-218-990-11
1-218-990-11
1-208-635-11
1-218-990-11
1-218-990-11
SHORT CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
0
0
10
0
0
0.5%
1/16W
R401
R402
R403
R404
R405
1-218-957-11
1-245-454-21
1-245-639-11
1-245-638-21
1-218-990-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
2.2K
0.022
2.2
1
0
5%
1%
1%
1%
1/16W
1/5W
1/2W
1W
R407
R411
1-218-990-11 SHORT CHIP
1-208-935-11 METAL CHIP
0
100K
0.5%
1/16W
< TRANSISTOR >
Q151
Q251
Q301
Q351
Q352
8-729-050-32
8-729-050-32
8-729-051-23
6-550-859-01
8-729-037-61
TRANSISTOR
TRANSISTOR
TRANSISTOR
FET
TRANSISTOR
2SC5585TL
2SC5585TL
2SA2018TL
NTHD4508NT1G
UN9113J-(TX).SO
Q401
Q404
Q405
Q431
Q432
6-550-326-01
6-550-192-01
8-729-055-00
8-729-046-45
8-729-044-57
TRANSISTOR
TRANSISTOR
TRANSISTOR
FET
TRANSISTOR
FZT968TA
DTC144EET1
UP04313008S0
SI2302DS-T1
FZT688B-TP
Q501
Q502
Q503
Q504
Q601
6-550-674-01
8-729-034-59
8-729-037-52
8-729-037-89
6-550-357-01
FET
TRANSISTOR
TRANSISTOR
TRANSISTOR
FET
MCH6604-K-TL-E
2SA1745-6.7-TL-E
2SD2216J-QR (TX).SO
2SC4627J-C (TX).SO
CPH5614-TL-E
Q602
6-550-740-01 FET
56
MCH6617-TL-E
MZ-NH1
MAIN
Ref. No.
Part No.
Description
Remark
R412
R413
R414
1-218-990-11 SHORT CHIP
1-220-804-11 RES-CHIP
1-208-943-11 METAL CHIP
0
2.2M
220K
5%
0.5%
1/16W
1/16W
R415
R416
R417
R418
R421
1-218-957-11
1-218-989-11
1-218-957-11
1-218-977-11
1-208-935-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
2.2K
1M
2.2K
100K
100K
5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R431
R432
R433
R453
R455
1-218-989-11
1-245-456-21
1-245-455-21
1-220-804-11
1-218-989-11
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1M
1
0.47
2.2M
1M
5%
1%
1%
5%
5%
1/16W
1/5W
1/5W
1/16W
1/16W
R456
R458
R459
R471
R473
1-218-985-11
1-220-804-11
1-218-981-11
1-218-990-11
1-218-941-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
470K
2.2M
220K
0
100
5%
5%
5%
1/16W
1/16W
1/16W
5%
1/16W
R474
R475
R491
R492
R493
1-218-941-11
1-218-990-11
1-208-699-11
1-208-699-11
1-218-990-11
RES-CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
100
0
4.7K
4.7K
0
5%
1/16W
0.5%
0.5%
1/16W
1/16W
R501
R502
R503
R504
R505
1-218-957-11
1-218-953-11
1-218-977-11
1-218-977-11
1-208-635-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
2.2K
1K
100K
100K
10
5%
5%
5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R507
R508
R509
R510
R511
1-218-957-11
1-218-957-11
1-218-990-11
1-216-864-11
1-218-990-11
RES-CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
2.2K
2.2K
0
0
0
5%
5%
1/16W
1/16W
R512
R513
R514
R515
R516
1-218-990-11
1-218-965-11
1-218-973-11
1-218-965-11
1-218-973-11
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
10K
47K
10K
47K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R517
R518
R519
R520
R524
1-218-965-11
1-218-973-11
1-218-953-11
1-218-949-11
1-218-945-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
47K
1K
470
220
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R525
R526
R561
R603
R604
1-216-864-11
1-218-990-11
1-218-981-11
1-218-985-11
1-218-990-11
SHORT CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
0
0
220K
470K
0
5%
5%
1/16W
1/16W
R605
R608
R609
R610
R612
1-218-965-11
1-218-446-11
1-218-981-11
1-218-965-11
1-220-804-11
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
1
220K
10K
2.2M
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/16W
R616
R617
R619
R620
R621
1-218-953-11
1-218-965-11
1-218-945-11
1-244-161-11
1-244-161-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
10K
220
2.2
2.2
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
Ref. No.
Part No.
Description
Remark
R622
R623
R624
R625
R628
1-244-161-11
1-244-161-11
1-218-985-11
1-218-985-11
1-218-933-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2
2.2
470K
470K
22
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R629
R630
R631
R632
R633
1-220-804-11
1-218-990-11
1-218-985-11
1-218-989-11
1-208-935-11
RES-CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
METAL CHIP
2.2M
0
470K
1M
100K
5%
1/16W
5%
5%
0.5%
1/16W
1/16W
1/16W
R634
R635
R636
R637
R638
1-218-977-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
RES-CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
100K
0
0
0
0
5%
1/16W
R640
R641
R642
R643
R644
1-218-989-11
1-245-456-21
1-245-456-21
1-218-981-11
1-218-985-11
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1M
1
1
220K
470K
5%
1%
1%
5%
5%
1/16W
1/5W
1/5W
1/16W
1/16W
R645
R647
R648
R650
R651
1-218-985-11
1-218-990-11
1-218-969-11
1-220-804-11
1-216-789-11
RES-CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
METAL CHIP
470K
0
22K
2.2M
2.2
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/10W
R653
R654
R656
R657
R658
1-218-990-11
1-220-804-11
1-218-990-11
1-218-945-11
1-218-990-11
SHORT CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
SHORT CHIP
0
2.2M
0
220
0
5%
1/16W
5%
1/16W
R660
R663
R668
R701
R702
1-216-864-11
1-218-945-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
220
0
0
0
5%
1/16W
R703
R704
R706
R707
R801
1-216-864-11
1-216-864-11
1-218-990-11
1-218-953-11
1-218-961-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
0
0
0
1K
4.7K
5%
5%
1/16W
1/16W
R802
R804
R805
R806
R807
1-218-937-11
1-218-933-11
1-218-933-11
1-218-961-11
1-218-957-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
47
22
22
4.7K
2.2K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R808
R809
R810
R811
R812
1-218-953-11
1-218-990-11
1-218-990-11
1-218-965-11
1-218-977-11
RES-CHIP
SHORT CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
1K
0
0
10K
100K
5%
1/16W
5%
5%
1/16W
1/16W
R813
R814
R815
R817
R818
1-218-990-11
1-218-965-11
1-218-981-11
1-218-953-11
1-218-957-11
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
10K
220K
1K
2.2K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R819
R820
1-218-953-11 RES-CHIP
1-218-945-11 RES-CHIP
1K
220
5%
5%
1/16W
1/16W
57
MZ-NH1
MAIN
Ref. No.
Part No.
Description
Part No.
Description
R895
R902
R903
R904
R906
1-218-990-11
1-218-941-11
1-218-989-11
1-218-989-11
1-218-977-11
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
100
1M
1M
100K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R907
R908
R910
R912
R914
1-218-965-11
1-218-969-11
1-208-715-11
1-218-981-11
1-208-707-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
10K
22K
22K
220K
10K
5%
5%
0.5%
5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
1-218-981-11
1-218-985-11
1-218-977-11
1-218-990-11
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
220K
470K
100K
0
470K
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R917
R918
R922
R923
R924
5%
1/16W
1/16W
1/16W
R925
R926
R927
R929
R931
1-208-927-11
1-208-935-11
1-208-683-11
1-208-935-11
1-218-990-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
47K
100K
1K
100K
0
0.5%
0.5%
0.5%
0.5%
1/16W
1/16W
1/16W
1/16W
R933
R934
R935
R936
R937
1-208-943-11
1-208-715-11
1-208-935-11
1-208-927-11
1-208-715-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
22K
100K
47K
22K
0.5%
0.5%
0.5%
0.5%
0.5%
1/16W
1/16W
1/16W
1/16W
1/16W
R938
R939
R940
R941
R944
1-208-927-11
1-208-927-11
1-218-981-11
1-218-990-11
1-218-990-11
METAL CHIP
METAL CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
47K
47K
220K
0
0
0.5%
0.5%
5%
1/16W
1/16W
1/16W
R945
R946
R947
R952
R953
1-218-990-11
1-218-977-11
1-218-973-11
1-218-973-11
1-218-973-11
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
100K
47K
47K
47K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R954
R956
R957
R958
1-218-985-11
1-218-973-11
1-218-985-11
1-218-990-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
470K
47K
470K
0
5%
5%
5%
1/16W
1/16W
1/16W
Remark
R821
R822
R823
1-220-804-11 RES-CHIP
1-218-989-11 RES-CHIP
1-218-965-11 RES-CHIP
2.2M
1M
10K
5%
5%
5%
1/16W
1/16W
1/16W
R824
R825
R826
R827
R828
1-208-635-11
1-218-990-11
1-218-990-11
1-208-635-11
1-218-957-11
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
RES-CHIP
10
0
0
10
2.2K
0.5%
1/16W
0.5%
5%
1/16W
1/16W
R830
R832
R833
R834
R835
1-218-990-11
1-218-933-11
1-216-864-11
1-208-943-11
1-218-985-11
SHORT CHIP
RES-CHIP
SHORT CHIP
METAL CHIP
RES-CHIP
0
22
0
220K
470K
5%
1/16W
0.5%
5%
1/16W
1/16W
R836
R837
R839
R840
R843
1-208-927-11
1-218-957-11
1-218-990-11
1-218-990-11
1-218-990-11
METAL CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
47K
2.2K
0
0
0
0.5%
5%
R845
R846
R847
R848
R849
1-208-943-11
1-218-973-11
1-218-990-11
1-218-990-11
1-218-990-11
METAL CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
220K
47K
0
0
0
0.5%
5%
R850
R852
R854
R855
R856
1-216-864-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R857
R858
R859
R860
R861
1-218-990-11
1-218-957-11
1-218-989-11
1-218-989-11
1-218-941-11
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
2.2K
1M
1M
100
R862
R863
R864
R865
R866
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
1-218-990-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R867
R868
R869
R870
R871
1-218-990-11
1-218-990-11
1-218-989-11
1-218-990-11
1-218-981-11
SHORT CHIP
SHORT CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
0
0
1M
0
220K
R872
R876
R881
R882
R883
1-218-990-11
1-218-990-11
1-218-989-11
1-218-977-11
1-218-977-11
SHORT CHIP
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
0
1M
100K
100K
R884
R885
R886
R887
R888
1-218-981-11
1-218-973-11
1-220-804-11
1-218-981-11
1-218-990-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
R890
R891
R892
R893
R894
1-218-965-11
1-218-977-11
1-218-977-11
1-218-990-11
1-218-965-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
58
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
5%
1/16W
5%
1/16W
5%
5%
5%
1/16W
1/16W
1/16W
220K
47K
2.2M
220K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
10K
100K
100K
0
10K
5%
5%
5%
1/16W
1/16W
1/16W
5%
1/16W
Ref. No.
Remark
< COMPOSITION CIRCUIT BLOCK >
RB701
RB702
1-233-963-21 RES, NETWORK (CHIP TYPE) 2.2K
1-233-967-11 RES, NETWORK (CHIP TYPE) 10K
< SWITCH >
S431
S891
S892
S893
S895
1-786-545-21 SWITCH, PUSH LEVER (S)
(BATTERY INSERT DETECT)
1-786-672-21 SWITCH, PUSH (2 KEY) (PROTECT DETECT)
1-786-448-21 SWITCH, PUSH (1 KEY) (HALF LOCK)
1-786-101-22 SWITCH, DETECTION (OPEN/CLOSE DETECT)
1-786-436-21 SWITCH, SLIDE (HOLD)
< VIBRATOR >
X801
1-795-780-21 VIBRATOR, CERAMIC (48MHz)
X802
1-795-779-21 VIBRATOR, CRYSTAL (22.5792MHz)
X872
1-795-602-11 VIBRATOR, CRYSTAL (32.768kHZ)
************************************************************
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
MZ-NH1
Ref. No.
Part No.
Description
Remark
MISCELLANEOUS
**************
10
64
0 163
M701
M702
1-805-493-11 LCD MODULE
1-478-469-11 SWITCH UNIT
X-2021-779-1 SERVICE ASSY, OP (ABX-U)
(including HR601 (OVER WRITE HEAD))
8-835-782-02 MOTOR, DC SSM18D/C-NP (SPINDLE)
8-835-778-11 MOTOR, DC SSM21A/C-NP (SLED)
M703
1-477-519-21 MOTOR UNIT, DC
(OVER WRITE HEAD UP/DOWN)
************************************************************
Ref. No.
Part No.
Description
0 501
0 501
0 501
0 501
0 501
1-478-393-11
1-478-394-11
1-478-395-11
1-478-396-11
1-478-397-11
ADAPTOR, AC (AC-ES608K) (US, TW)
ADAPTOR, AC (AC-ES608K) (AEP, E18)
ADAPTOR, AC (AC-ES608K) (UK, HK)
ADAPTOR, AC (AC-ES608K) (KR)
ADAPTOR, AC (AC-ES608K) (JE)
0 501
0 501
0 502
0 502
503
1-478-398-11
1-478-399-11
1-478-470-11
1-478-470-21
1-478-468-11
ADAPTOR, AC (AC-ES608K) (CH)
ADAPTOR, AC (AC-ES608K) (AUS)
STAND, CHARGE (for SILVER)
STAND, CHARGE (for GOLD)
REMOTE COMMANDER (RM-MC40ELK)
(US, AEP, UK, TW, KR, AUS)
503
ACCESSORIES
************
0
1-469-089-11 FILTER, CLAMP (FERRITE CORE)
(for RM-MC40ELK: SIZE S) (EXCEPT E18, JE)
1-543-793-11 FILTER, CLAMP (FERRITE CORE)
(for OPTIONAL STEREO MIKE: SIZE S)
(EXCEPT E18, JE)
1-543-798-11 FILTER, CLAMP (FERRITE CORE)
(for OPTIONAL CONNECTING CORD
(ANALOG TYPE): SIZE L)
(AEP, UK, HK, TW, KR, AUS, CH)
1-569-007-12 ADAPTOR, CONVERSION 2P (JE)
1-794-451-11 CONNECTOR, OPTICAL
(US, AEP, UK, TW, AUS, E18)
1-794-451-51 CONNECTOR, OPTICAL (HK, KR, CH, JE)
2-109-705-12 CD-ROM (APPLICATION)
(SonicStage/MD Single Burner) (US)
2-109-705-22 CD-ROM (APPLICATION)
(SonicStage/MD Single Burner) (AEP, UK)
2-179-850-31 CD-ROM (APPLICATION)
(SonicStage/MD Single Burner)
(HK, TW, KR, AUS, CH, E18)
2-179-850-41 CD-ROM (APPLICATION) (JE)
3-220-749-01 CASE, CARRYING (EXCEPT US)
3-266-450-12 MANUAL, INSTRUCTION (ENGLISH)
(EXCEPT KR)
3-266-450-21 MANUAL, INSTRUCTION (FRENCH) (AEP)
3-266-450-31 MANUAL, INSTRUCTION (GERMAN) (AEP)
3-266-450-41 MANUAL, INSTRUCTION (SPANISH) (AEP, JE)
3-266-450-51
3-266-450-61
3-266-450-71
3-266-450-81
MANUAL, INSTRUCTION (DUTCH) (AEP)
MANUAL, INSTRUCTION (SWEDISH) (AEP)
MANUAL, INSTRUCTION (ITALIAN) (AEP)
MANUAL, INSTRUCTION (PORTUGUESE)
(AEP, JE)
3-266-450-91 MANUAL, INSTRUCTION (FINNISH) (AEP)
3-266-451-11 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE) (HK, TW, E18, JE)
3-266-451-21 MANUAL, INSTRUCTION
(SIMPLIFIED CHINESE) (CH, JE)
3-266-451-31 MANUAL, INSTRUCTION (KOREAN) (KR, JE)
Remark
1-478-468-21 REMOTE COMMANDER (RM-MC40ELK)
(HK, CH, E18, JE)
8-953-218-91 RECEIVER MDR-E838SP/SK SET
1-828-071-11 CORD, CONNECTION (USB)
(including FERRITE CORE)
1-756-425-21 BATTERY, STORAGE, LITHIUM (LIP-4WM) (US)
1-756-425-31 BATTERY, STORAGE, LITHIUM (LIP-4WM)
(EXCEPT US)
504
505
506
506
507
X-2022-498-1 BATTERY CASE ASSY
501
AC power adaptor (1)
503
Remote control (1)
505
Dedicated USB cable (1)
502
Battery charging stand (1)
504
Headphones/earphones (1)
506
LIP-4WM Lithium-ion
rechargeable battery (1)
507
Rechargeable battery case (1)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
59
MZ-NH1
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
2
Ver.
Date
Description of Revision
1.0
2004.07
New
1.1
2004.09
Change of Part No. for Hi-MD3 adjustment disc HMD1GSDJ
(SPM-04101)
Download PDF

advertising