Sony | RM-PP404 | User's Manual | Sony RM-PP404 User's Manual

4-227-692-12(1)
Remote
Commander
Operating Instructions
RM-PP404
 2000 Sony Corporation
Precautions
About This Manual
On safety
The instructions in this manual are for model RM-PP404.
Check your model number by looking at the lower right
corner of the front side.
Should any solid object or liquid fall into the cabinet, unplug the
receiver and have it checked by qualified personnel before
operating it any further.
On operation
Before connecting other components, be sure to turn off and
unplug the receiver.
On cleaning
Clean the cabinet, panel and controls with a soft cloth slightly
moistened with a mild detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent such as alcohol or
benzine.
If you have any question or problem concerning your
receiver, please consult your nearest Sony dealer.
2
Conventions
The following icon is used in this manual:
z Indicates hints and tips for making the task easier.
Before You Use Your
Remote
Check that you received the following item with the
remote:
R6 (size-AA) batteries (2)
Inserting batteries into the remote
Insert two R6 (size-AA) batteries with the + and –
properly oriented in the battery compartment. When
using the remote, point it at the remote sensor on the
receiver.
TABLE OF CONTENTS
Location of Parts and Basic Remote
Operations 4
Parts Description
4
Advanced Remote Operations
11
Operating Other Components 12
Additional Information 16
]
}
]
}
Troubleshooting 16
Specifications 17
z When to replace batteries
Under normal conditions, the batteries should last for about 6
months. When the remote no longer operates the receiver,
replace both batteries with new ones.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not expose the remote sensor of the receiver to direct
sunlight or lighting apparatuses. Doing so may cause a
malfunction.
• If you don’t use the remote for an extended period of time,
remove the batteries to avoid possible damage from battery
leakage and corrosion.
3
Location of
Parts and Basic
Remote
Operations
This chapter provides information on
the location of buttons and how to use
them to perform basic operations.
However, some functions explained in
this section may not work depending
on the model of the receiver.
For the functions of the receiver you
purchased, refer to the Operating
Instructions supplied with the
receiver.
Parts Description
1
3
SYSTEM STANDBY
2
1
2
3
4
5
6
7
8
SHIFT
>10 - / - –
0
VOL +
n
N
9
ENTER
D.TUNING
MUTING
X
x
M
– SUB CH +
.
>
m
DISC
D.SKIP
ANT
TV/VTR
z
O
RETURN
VIDEO1
VIDEO2
VIDEO3
TV/SAT
AUX
MD/TAPE
DVD/LD
4
CD
TV CONTROL
TUNER
PHONO
SOUND FIELD
A.F.D.
2CH
8
9
4
?/1
AV
?/1
SLEEP
MODE
ANALOG
DIRECT
CIMEMA
STUDIO
BASS
BOOST
5.1CH
5
MUTING IR SET
MASTER
VOLUME CH/PRESET
7
+ +
– –
6
2 AV ?/1 switch
Press to turn the selected audio and video components
under the function button, on or off.
If you press the ?/1 switch (3) at the same time, it
will turn off the main component and other Sony
audio/video components (SYSTEM STANDBY).
Note that the function buttons are factory-set as
described in the table above. If you want to change
the factory setting of the buttons to match your
particular components, do the procedure “Changing
the Factory Setting of a Function Button” on page 12.
Note
After you have selected VCR or DVD player, turn on the TV
and set the TV’s video input to match the component you
selected.
Note
The function of the AV ?/1 switch changes automatically
each time you press the function buttons (4). Depending on
the component, the above operation may not be be possible
or may operate differently than described.
3 ?/1 switch
Press to turn the receiver on or off.
4 Function buttons
Press one of the buttons to select the component you
want to use. When you press a button, the receiver
turns on. The components are factory assigned to the
buttons as follows. When you want to assign other
components, program the remote following the steps
on page 12.
Button(s)
Assigned component(s)
VIDEO1
VIDEO2
VIDEO3
VCR(VTR mode 3)
VCR(VTR mode 1)
VCR(VTR mode 2)
DVD/LD
DVD player
TV/SAT
TV tuner
AUX
—
MD/TAPE
MD deck
CD
CD player
TUNER
Built-in tuner*
PHONO
Turntable*
5.1 CH
DVD player
TV CONTROL
TV tuner
* The setting cannot be changed.
See the table on page 10 for information on the buttons
that you can use to control each component.
5 TV CONTROL button
If you are using a TV, you can use this remote to
operate the TV without turning on the receiver. When
you are using a Sony TV, pressing this button turns on
the TV and switches to TV input.
6 MASTER VOLUME +/– buttons
Press to adjust the volume level of all speakers at the
same time.
7 MUTING button
Press to mute the sound. The MUTING indicator on
the receiver lights up when the sound is muted.
8 SOUND FIELD buttons
A.F.D. button
Press to set the receiver to automatically select the
appropriate sound field for the input signal.
This button can be used only with receivers that have
digital inputs.
2CH button
Press to turn the sound field off and listen to 2 channel
stereo sound.
Multi channnel source is also downmixed to a 2
channel stereo sound.
MODE button
Press to select sound fields.
ANALOG DIRECT button
Press to listen to an analog source without digital
processing by the equalizer, sound field, etc.
CINEMA STUDIO button
Press to select CINEMA STUDIO in the sound field
menu.
9 BASS BOOST button
Press to increase the bass of the front speakers. The
BASS BOOST indicator on the receiver lights up when
the function is turned on.
5
Location of Parts and Basic Remote Operations
1 SLEEP button
Press repeatedly to activate the sleep function and the
duration which the receiver turns off automatically.
Parts Description
Location of Parts and Basic Remote Operations
0 CURSOR MODE button
Press repeatedly to select a cursor mode, SURROUND,
BASS/TREBLE (EQ), etc. The indicator for the
selected cursor mode lights up on the receiver.
DVD
MENU
VCR
MENU
EXECUTE
ENTER
SAT
MENU
CURSOR
MODE
0
SAT
DVD
GUIDE EXIT/RETURN TITLE
TV
TV/VIDEO
WIDE
qg
P IN P
SWAP
POSITION
JUMP
TEST
EQ/TONE TONE
LEVEL
+
+
REAR
CENTER
–
–
V
qa
qs
qd
qa EQ/TONE button
Press to turn the tone effect on or off. The TONE
indicator on the receiver lights up while the tone effect
is turned on.
Note that if you have adjusted the tone using the
CURSOR MODE button and cursor buttons, the
adjusted tone will be produced whenever you turn on
the tone effect.
qs TEST TONE button
Press to output a test tone.
qf
Lift up the top cover.
qd LEVEL CENTER +/– buttons
Press to adjust the volume level of the center speaker.
qf LEVEL REAR +/– buttons
Press to adjust the volume level of the rear speakers.
?/1
AV
?/1
SLEEP
qg TV buttons
SYSTEM STANDBY
1
2
3
4
5
6
7
8
SHIFT
>10 - / - –
0
VOL +
n
N
TV/VIDEO button
Press to change the input mode of the TV.
9
ENTER
D.TUNING
MUTING
X
x
M
– SUB CH +
.
>
m
DISC
D.SKIP
ANT
TV/VTR
z
O
RETURN
VIDEO1
VIDEO2
VIDEO3
TV/SAT
AUX
MD/TAPE
TUNER
PHONO
5.1CH
DVD/LD
MODE
ANALOG
DIRECT
CINEMA
STUDIO
BASS
BOOST
P IN P button
Press to activate the picture-in-picture function*.
SWAP button
Press to swap the small and large pictures*.
CD
TV CONTROL
SOUND FIELD
A.F.D.
2CH
WIDE button
Press to switch the TV to the wide mode.
MUTING IR SET
POSITION button
Press to change the position of the small picture*.
MASTER
VOLUME CH/PRESET
+ +
– –
JUMP button
Press to toggle between the previous and the current
channels.
*
6
Only with Sony TVs with the picture-in-picture function.
The button pressed first
ql
DVD
MENU
VCR
MENU
qh
qj
EXECUTE
ENTER
w;
wa
SAT
MENU
CURSOR
MODE
SAT
DVD
GUIDE EXIT/RETURN TITLE
TV
TV/VIDEO
WIDE
P IN P
SWAP
POSITION
JUMP
qk
TEST
EQ/TONE TONE
LEVEL
+
+
REAR
CENTER
–
–
Lift up the top cover.
qh VCR MENU button
Press to display the VCR menu on the TV screen.
Then use the cursor buttons on the remote to perform
the menu operations (see “qj Cursor buttons (V/v/
B/b), EXECUTE/ENTER button, and EXIT/RETURN
button” on this page).
Note
After you press the VCR MENU button, the remote is set to
control the VCR that corresponds to the last selected VCR.
qj Cursor buttons (V/v/B/b), EXECUTE/ENTER button,
and EXIT/RETURN button
After pressing the CURSOR MODE button or SET UP
button on the receiver, use the cursor buttons to make
specific settings (see page 6).
After pressing the VCR MENU, DVD MENU, DVD
TITLE, SAT MENU, or SAT GUIDE button, use these
buttons to perform the following operations:
Cursor buttons: To select a menu item
EXECUTE/ENTER button: To enter the selection
EXIT/RETURN button: To return to the previous
menu or exit the menu
CURSOR
MODE
SAT
MENU
SAT
GUIDE
VCR
MENU
DVD
MENU
DVD
TITLE
Cursor
buttons
z
z
z
z
EXECUTE/
ENTER
z
z
z
z
Operable
buttons
EXIT/
RETURN
z
z
qk DVD TITLE button
Press to display the DVD title menu. Then use the
cursor buttons on the remote to perform the menu
operations (see “qj Cursor buttons (V/v/B/b),
EXECUTE/ENTER button, and EXIT/RETURN
button” on this page.
ql DVD MENU button
Press to display the DVD menu. Then use the cursor
buttons on the remote to perform the menu operations
(see “qj Cursor buttons (V/v/B/b), EXECUTE/
ENTER button, and EXIT/RETURN button” on this
page).
w; SAT MENU button
Press to display the SAT menu. Then use the cursor
buttons on the remote to perform the menu operations
(see “qj Cursor buttons (V/v/B/b), EXECUTE/
ENTER button, and EXIT/RETURN button” on this
page).
wa SAT GUIDE button
Press to display the SAT guide. Then use the cursor
buttons on the remote to perform the menu operations
(see “qj Cursor buttons (V/v/B/b), EXECUTE/
ENTER button, and EXIT/RETURN button” on this
page).
7
Location of Parts and Basic Remote Operations
Some of these buttons do not operate after a particular
button is pressed. See the table below to find out
which buttons operate after which button is pressed.
Parts Description
ws SHIFT >10 -/-- button*
Location of Parts and Basic Remote Operations
AV
?/1
SLEEP
wk
If you have selected tuner:
Press repeatedly to select a memory page for
presetting radio stations or tuning to preset stations.
?/1
SYSTEM STANDBY
1
2
3
4
5
6
7
8
9
SHIFT
ws
>10 - / - –
0
VOL +
n
N
wd
ENTER
D.TUNING
wf
MUTING
X
x
.
>
m
M
DISC
D.SKIP
ANT
TV/VTR
– SUB CH +
wg
z
O
VIDEO2
VIDEO3
TV/SAT
AUX
MD/TAPE
DVD/LD
wj
If you have selected tuner:
Press to enter direct tuning mode.
CD
TV CONTROL
TUNER
PHONO
SOUND FIELD
A.F.D.
2CH
MODE
ANALOG
DIRECT
CINEMA
STUDIO
BASS
BOOST
5.1CH
MUTING IR SET
MASTER
VOLUME CH/PRESET
+ +
– –
wd Numeric buttons (1 to 0)*
Inputs the corresponding numeric value. When
inputting a channel, disc, or track number, 0 selects 10.
wf ENTER D.TUNING button*
RETURN
VIDEO1
If you selected VCR, TV, LD player, tape deck, MD
deck, or CD player:
Press before inputting a channel or track number of
eleven or higher.
wl
wh
If you have selected VCR, DVD player, LD player,
TV, satellite tuner, tape deck, MD deck, or CD
player:
After selecting a channel, disc, or track using the
numeric buttons, press to enter the value.
* The function of these buttons switch automatically each time
you press the function buttons (4). The above explanation is
intended to serve as an example only. Therefore, depending on
the component, the above operation may not be be possible or
may operate differently than described.
8
Button(s)
Function
n
Starts play on the reverse side of the cassette.
VOL –
Lowers the volume.
N
Starts play. (Starts play on the front side of the
cassette.)
VOL +
Raises the volume.
X
Pauses play or recording or starts recording
when the component is in recording standby.
MUTING
Mutes the sound.
x
Stops play.
./>
Skips tracks.
SUB CH +/– Changes the sub channel selection higher and
lower.
m/M
Fast forwards or rewinds.
wh CH/PRESET +/– buttons*
Press repeatedly to select a preset station or channel.
wj ANT TV/VTR/RETURN button*
Press repeatedly to select the signal to be output from
the antenna terminal of the VCR (TV signal or video
signal). With a DVD player, press to go back to
previous on-screen menus or to resume playback.
wk Program indicator*
Lights up whenever any button on the remote is
pressed. Also lights up during programming (see
page 13).
wl IR SET button
Use this button to program the remote with the signals
to control non-Sony components (see page 13).
* The function of these buttons switch automatically each time
you press the function buttons (4). The above explanation is
intended to serve as an example only. Therefore, depending on
the component, the above operation may not be be possible or
may operate differently than described.
Searches tracks in the forward or backward
direction.
z
Sets the deck in recording standby.
z+N
(if pressed
together)
Starts recording. You can press n for the tape
deck instead of N.
DISC
Selects a disc (with a multi-disc changer only).
D.SKIP
Skips a disc (with a multi-disc changer only).
9
Location of Parts and Basic Remote Operations
wg Operation buttons*
The following table describes the component operated
by each button and the function of the buttons. See the
table on page 10 for information on the buttons that
you can use to control each component.
Parts Description
Table of buttons that you can use to control each component
Location of Parts and Basic Remote Operations
Component
CD
DAT deck MD deck
player
Tape
deck (A
and B)
LD
player
VCR
TV
Satellite
tuner/
Cable box
Video
CD
player
DVD
player
z
z
z
z
z
z
z
z
z
Button(s)
AV ?/1
z
z
z
Numeric buttons
z
z
z
z
z
z
z
SHIFT >10 -/--
z
z
z
z
z
z
ENTER D.TUNING
z
z
z
z
z
z
z
n
z
z
z
z
z
z
z
z
z
z
z
z
z
VOL +
X
z
z
VOL –
N
z
z
z
z
z
z
z
z
MUTING
x
z
z
z
z
z
z
z
z
./>
z
z
z
z**
z
z
z
z
z
z
z
SUB CH +/–
m/M
z
DISC
z*
D.SKIP
z*
z
z
z
z
z*
z
ANT TV/VTR
z
RETURN
z
z
z+N
z
z+n
* With a multi-disc changer only.
** B deck only
10
z
z
z
z
z
z
z
z
Advanced
Remote
Operations
?/1
AV
?/1
SLEEP
Program
indicator
?/1
SYSTEM STANDBY
AV ?/1
1
2
3
4
5
6
7
8
SHIFT
>10 - / - –
0
VOL +
n
N
Numeric
buttons
9
ENTER
D.TUNING
MUTING
X
x
M
ENTER
D.TUNING
– SUB CH +
.
>
m
DISC
D.SKIP
ANT
TV/VTR
z
O
RETURN
VIDEO1
VIDEO2
VIDEO3
TV/SAT
AUX
MD/TAPE
DVD/LD
CD
TV CONTROL
TUNER
PHONO
SOUND FIELD
A.F.D.
2CH
MODE
ANALOG
DIRECT
CIMEMA
STUDIO
BASS
BOOST
Function
buttons
5.1CH
MUTING IR SET
IR SET
MASTER
VOLUME CH/PRESET
+ +
– –
MASTER
VOLUME –
11
Advanced Remote Operations
This chapter describes how to change
the factory setting of a function button
and how to set the remote to control
non-Sony components.
Brief descriptions of buttons used for
advanced remote operations
Program indicator: Lights up during programming
operations.
Advanced Remote Operations
?/1, AV ?/1, MASTER VOLUME – : Press these buttons
at the same time to reset all the function buttons to the
factory settings and to clear the programmed signals set
for operation of non-Sony components.
Numeric buttons: Use when changing the factory
settings of the function buttons or specifying the maker of
the component that you want to control using the remote.
ENTER D.TUNING: Use when changing the factory
settings of the function buttons or setting the remote to
operate non-Sony components.
Function buttons: Come with factory settings that can be
changed to suit the components you have.
Operating Other
Components
You can program the remote to control other components
by changing the code or non-Sony components. Once the
control signals have been memorized, you can use those
components as part of your system.
Furthermore, you can also program this remote for Sony
components that the remote is unable to control. Note
that the remote can control the components that accept
infrared wireless control signals only.
Notes
• The settings of PHONO and TUNER cannot be changed.
• When you assign a component to the TV CONTROL button,
you can operate the programmed component without changing
the function of the receiver.
1
Press IR SET.
The program indicator lights up.
2
Press the function button for the component you
want to control.
For example, if you are going to control a CD player,
press CD.
3
Press the numeric buttons to enter the numeric
code (or one of the codes if more than one code
exist) corresponding to the component and the
make of the component you want to control.
See the tables on pages 14 and 15 for information on
the numeric code(s) corresponding to the component
and the maker of the component (the first digit and
the last two digits of the numeric code(s) correspond
to the category and the maker’s code respectively).
4
Press ENTER D.TUNING.
When the program indicator flashes twice, the
component(s) can then be controlled using this
remote.
5
Repeat Steps 1 to 4 to control other components.
IR SET: Press to set the remote to operate non-Sony
components.
12
z If programming is unsuccessful, check the following:
• If the program indicator does not light up in Step 1, the
batteries are weak. Replace both batteries.
• If you do not do Step 2 within twenty seconds after pressing
the IR SET button in Step 1, the remote automatically exits
programming mode. Start again from Step 1.
• To redo a setting during programming, press IR SET to return
to step 2.
• After Step 1, only the first function button that is pressed will
register. If you press more than one function button, it will not
register.
• In step 3, only the first three numbers entered are valid.
• If you enter an unidentified preset number, the program
indicator goes off without flashing after pressing ENTER
D.TUNING in step 4, then the remote exits programming
mode. The previously programmed settings are memorized.
Clearing all programmed signals
To clear all the programmed signals, do the following
procedure. The remote is reset to its factory-setting.
Use the numeric codes in the tables below to control nonSony conponents and also Sony components that the
remote is normally unable to control. Since the remote
signal that a component accepts differs depending on the
model and year of the component, more than one numeric
code may be assigned to a component. If you fail to
program your remote using one of the codes, try using
other codes.
Notes
• The numeric codes are based on the latest information available
for each brand. There is a chance, however, that your
component will not respond to some or all of the codes.
• All of the functions on this remote may not be available when
used with your particular component.
First press down MASTER VOLUME –, then AV ?/1,
and then ?/1 until the program indicator flashes three
times, then goes off.
13
Advanced Remote Operations
Notes
The numeric codes corresponding to the
component and the maker of the
component
Operating Other Components
To control a tape deck
To control a CD player
Advanced Remote Operations
Maker
Code(s)
SONY
201, 202
DENON
204, 205
KENWOOD
206, 207, 208, 209
NAKAMICHI
210
PANASONIC
216
PHILIPS
211, 212
PIONEER
213, 214
TECHNICS
215, 216
YAMAHA
217, 218
Maker
Code(s)
SONY
101, 102
DENON
103, 104
JVC
105, 106, 107
KENWOOD
108, 109, 110
MAGNAVOX
111, 116
MARANTZ
116
ONKYO
112, 113, 114
PANASONIC
115
PHILIPS
116
PIONEER
117
To control an LD player
TECHNICS
115, 118, 119
Maker
Code(s)
YAMAHA
120, 121, 122
SONY
601, 602, 603, 604
PIONEER
606
To control a DAT deck
Maker
Code(s)
To control a video CD player
SONY
203
Maker
Code(s)
PIONEER
219
SONY
605
To control an MD deck
Maker
Code(s)
SONY
301
DENON
302
JVC
303
KENWOOD
304
14
To control a VCR
To control a TV
Code(s)
Maker
Code(s)
SONY
701, 702, 703, 704, 705, 706
SONY
501
AIWA
710, 750, 757, 758
DAEWOO
502, 504, 505, 506, 507, 515
AKAI
707, 708, 709, 759
FISHER
508
BLAUPUNKT
740
GOLDSTAR
502, 503, 511, 512, 515, 534
EMERSON
711, 712, 713, 714, 715, 716, 750
GRUNDIG
517, 534
FISHER
717, 718, 719, 720
HITACHI
502, 513, 514, 515
GENERAL ELECTRIC 721, 722, 730
ITT/NOKIA
521, 522
GOLDSTAR
723, 753
JVC
516
GRUNDIG
724
MAGNAVOX
502, 503, 518
HITACHI
722, 725, 729, 741
MITSUBISHI/MGA
502, 503, 519
ITT/NOKIA
717
NEC
502, 503, 520
JVC
726, 727, 728, 736
PANASONIC
509, 524
MAGNAVOX
730, 731, 738
PHILIPS
515, 518
MITSUBISHI/MGA
732, 733, 734, 735
PIONEER
509, 525, 526, 540
NEC
736
RCA/PROSCAN
502, 510, 527, 528, 529
PANASONIC
729, 730, 737, 738, 739, 740
SAMSUNG
502, 503, 515, 531, 532, 533, 534
PHILIPS
729, 730, 731
SANYO
508
PIONEER
729
SHARP
535
RCA/PROSCAN
722, 729, 730, 731, 741, 747
TELEFUNKEN
523, 536, 537, 538
SAMSUNG
742, 743, 744, 745
THOMSON
530, 537, 539
SANYO
717, 720, 746
TOSHIBA
535, 540, 541
SHARP
748, 749
ZENITH
542, 543
TELEFUNKEN
751, 752
TOSHIBA
747, 755, 756
ZENITH
754
Advanced Remote Operations
Maker
To control a satellite tuner or cable box
Maker
Code(s)
SONY
801, 802
To control a DVD player
JERROLD/G.I.
806, 807, 808, 809, 810, 811, 812, 813, 814
Maker
Code(s)
PANASONIC
803
SONY
401
RCA
804, 805
PANASONIC
402, 406
S. ATLANTA
815, 816, 817
PIONEER
403
TOSHIBA
404
DENON
405
15
Additional
Information
Troubleshooting
If you experience any of the following difficulties while
using the receiver, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
The remote does not function.
, Point the remote at the remote sensor on the
receiver.
, Remove any obstacles in the path between the
remote and the receiver.
, Replace both batteries in the remote with new
ones, if they are weak.
, Make sure you select the correct function on the
remote.
16
Specifications
General
Remote control system
Infrared control
Power requirements
3 V DC with two R6 (size-AA)
batteries
Dimensions
210 × 56 × 25 mm
Mass (approx.)
130 g excluding batteries
Additional Information
Design and specifications are subject to change without
notice.
17
Additional Information
18
Additional Information
19
Sony Corporation
Printed in Malaysia
Download PDF

advertising