Sony SLV-D930 DVD Player/VCR Operating Instructions

2-109-225-13 (2) GB
DVD Player/
Video Cassette
Recorder
Operating Instructions
PAL
SLV-D930 GI
© 2004 Sony Corporation
WARNING
To prevent fire or shock
hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to
qualified personnel only.
Mains lead must only be
changed at a qualified
service shop.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.
CAUTION
The use of optical instruments
with this product will increase
eye hazard. As the laser beam
used in this DVD player/
Video Cassette Recorder is
harmful to eyes, do not
attempt to disassemble the
cabinet.
Refer servicing to qualified
personnel only.
Notice for customers in
the United Kingdom and
Republic of Ireland
A moulded plug complying
with BS1363 is fitted to this
equipment for your safety and
convenience.
Should the fuse in the plug
supplied need to be replaced, a
3 AMP fuse approved by
ASTA or BSI to BS1362, (i.e.,
marked with
or
mark)
must be used.
If the plug supplied with this
equipment has a detachable
fuse cover, be sure to attach
the fuse cover after you
change the fuse. Never use the
plug without the fuse cover. If
you should lose the fuse cover,
please contact your nearest
Sony service station.
2
WARNING
Welcome!
Precautions
Safety
• This unit operates on 220 –
240 V AC, 50 Hz. Check
that the unit’s operating
voltage is identical with
your local power supply.
• To prevent fire or shock
hazard, do not place objects
filled with liquids, such as
vases, on the apparatus.
• The unit is not
disconnected from the AC
power source (mains) as
long as it is connected to
the wall outlet, even if the
unit itself has been turned
off.
Installing
• Do not install the unit in a
confined space such as a
bookshelf or similar unit.
• Do not install the unit in an
inclined position. It is
designed to be operated in a
horizontal position only.
• Keep the unit and discs
away from equipment with
strong magnets, such as
microwave ovens, or large
loudspeakers.
• Do not place heavy objects
on the unit.
• Do not place the unit on
surfaces (rugs, blankets,
etc.) or near materials
(curtains, draperies) that
may block the ventilation
slots.
VIDEO Plus+ and PlusCode
are registered trademarks of
Gemstar Development
Corporation. The VIDEO
Plus+ system is manufactured
under license from Gemstar
Development Corporation.
Thank you for purchasing this
Sony DVD Player/Video
Cassette Recorder. Before
operating this player, please
read this manual thoroughly
and retain it for future
reference.
Caution
For use of the VCR
Television programmes, films,
video tapes and other
materials may be copyrighted.
Unauthorized recording of
such material may be contrary
to the provisions of the
copyright laws. Also, use of
this recorder with cable
television transmission may
require authorization from the
cable television transmitter
and/or programme owner.
For use of the DVD
player
This product incorporates
copyright protection
technology that is protected by
U.S. patents and other
intellectual property rights.
Use of this copyright
protection technology must be
authorized by Macrovision,
and is intended for home and
other limited viewing uses
only unless otherwise
authorized by Macrovision.
Reverse engineering or
disassembly is prohibited.
Caution
3
Table of contents
2
2
3
6
6
7
WARNING
Welcome!
Caution
About this manual
This player can play the following discs
Notes about discs
Getting Started
8
9
11
14
16
17
19
Step 1 : Unpacking
Step 2 : Setting up the remote commander
Step 3 : Connecting the DVD-VCR
Step 4 : Setting up the DVD-VCR with the Auto Set Up function
Step 5 : Selecting a language
Step 6 : Setting the clock
Step 7 : Presetting channels
Basic Operations
27
31
34
35
39
43
Playing discs
Guide to the on-screen display
Locking the disc tray (Child Lock)
Playing a tape
Recording TV programmes
Recording TV programmes using the
VIDEO Plus+® system
47 Recording TV programmes using the
timer
50 Checking/changing/cancelling timer
settings
4
Table of contents
Advanced Hookups
52 A/V Receiver hookup
54 S-Video hookup
DVD Settings and
Adjustments
55 Audio Setup
58 Screen Setup
61 Setting the display or sound track
language
63 Parental Control (limiting playback
by children)
DVD Additional Operations
66
68
69
70
71
76
77
79
84
88
Using the DVD’s menu
Zooming into a scene
Changing the angles
Displaying the subtitle
Various play mode functions
(Programme play, Shuffle play,
Repeat play)
Changing the sound
Virtual surround setting
Playing an MP3 audio track
Playing JPEG image files
Playing VIDEO CDs with “PBC On/
Off” functions
VCR Additional Operations
90 Quick Timer Recording
92 Recording stereo and bilingual
programmes
94 Searching using index function
96 Adjusting the picture (tracking)
98 Changing menu options
100 Editing
Additional Information
103
105
111
113
114
119
120
General setup information
Troubleshooting
Glossary
Specifications
Index to parts and controls
DVD Audio/Subtitle Language
Index
Table of contents
5
About this manual
• This manual mainly explains operations
using the remote, but the same operations can
also be performed using the buttons on the
DVD-VCR having the same or similar
names.
• “DVD” may be used as a general term for
DVD VIDEOs, DVD-RWs/DVD-Rs, and
DVD+RWs/DVD+Rs.
• The meaning of the icons used in this manual
is described below:
Icon
Meaning
Functions available for DVD
VIDEOs and DVD-RWs/DVDRs in video mode or
DVD+RWs/DVD+Rs
Functions available for DVDRWs in VR (Video Recording)
mode
Functions available for VIDEO
CDs, Super VCDs or CD-Rs/
CD-RWs in video CD format or
Super VCD format
This player can play the
following discs
Format of discs
DVD VIDEO
DVD-RW
VIDEO CD
Music CD
“DVD VIDEO” and “DVD-RW” are
trademarks.
Region code
Functions available for DATA
CDs (CD-ROMs/CD-Rs/CDRWs containing MP3* audio
tracks or JPEG files)
Your player has a region code printed on the
back of the unit and only will play DVD VIDEO
discs (playback only) labelled with identical
region codes. This system is used to protect
copyrights.
Functions available for music
CDs or CD-Rs/CD-RWs in
music CD format
DVDs labelled
player.
Functions available for VHS
VIDEOs
* MP3 (MPEG 1 Audio Layer 3) is a standard format
defined by ISO/MPEG which compresses audio data.
ALL
will also play on this
If you try to play any other DVD VIDEO, the
message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the DVD VIDEO, no region code
indication may be labelled even though playing
the DVD VIDEO is prohibited by area
restrictions.
DVD PLAYER/
VIDEO CASSETTE RECORDER
MODEL NO. SLV-DXXXX
NO.
~AC 220–240V
50Hz 20W
X
6
About this manual
Region code
Example of discs that the player
cannot play
Note on playback operations of
DVDs and VIDEO CDs
The player cannot play the following discs:
• All CD-ROMs (including PHOTO CDs)/CDRs/CD-RWs other than those recorded in the
following formats:
– music CD format
– video CD format
– MP3 or JPEG format that conforms to
ISO9660* Level 1/Level 2
• Data part of CD-Extras
• DVD-ROMs
• DVD Audio discs
• HD layer on Super Audio CDs
Some playback operations of DVDs and VIDEO
CDs may be intentionally set by software
producers. Since this player plays DVDs and
VIDEO CDs according to the disc contents the
software producers designed, some playback
features may not be available. Also, refer to the
instructions supplied with the DVDs or VIDEO
CDs.
* A logical format of files and folders on CD-ROMs,
defined by ISO (International Standard
Organization).
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
Also, the player cannot play the following discs:
• A DVD VIDEO with a different region code.
• A disc recorded in a color system other than
PAL, such as NTSC or SECAM (this player
conforms to the PAL color system).
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane tape
or a sticker still left on it.
Notes about DVD-RWs/DVD-Rs,
DVD+RWs/DVD+Rs, or CD-Rs/CDRWs
Some DVD-RWs/DVD-Rs, DVD+RWs/
DVD+Rs, or CD-Rs/CD-RWs cannot be played
on this player due to the recording quality or
physical condition of the disc, or the
characteristics of the recording device and
authoring software.
The disc will not play if it has not been correctly
finalized. Also, images in DVD-RW discs with
CPRM* protection may not be played if they
contain a copy protection signal.
* CPRM (Content Protection for Recordable
Media) is a coding technology that protects
the copyright of images.
Music discs encoded with
copyright protection technologies
Notes about discs
• To keep the disc clean, handle the disc by its
edge. Do not touch the surface.
• Do not expose the disc to direct sunlight or
heat sources such as hot air ducts, or leave it in
a car parked in direct sunlight as the
temperature may rise considerably inside the
car.
• After playing, store the disc in its case.
• Clean the disc with a cleaning cloth.
Wipe the disc from the centre out.
Do not use solvents such as benzine, thinner,
commercially available cleaners, or anti-static
spray intended for vinyl LPs.
Notes about discs
7
Getting Started
Step 1 : Unpacking
Check that you have received the following items with the DVD-VCR:
• Remote commander
• Aerial cable
• R6 (size AA) batteries
• Audio cord
(pinplug ×2 y pinplug ×2)
• Video cord
(pinplug ×1 y pinplug ×1)
Note
• The supplied remote commander is for the exclusive use of this DVD-VCR.
8
Unpacking
Step 2 : Setting up the remote commander
Inserting the batteries
Getting Started
Insert two size AA (R6) batteries
by matching the + and – on the
batteries to the diagram inside the
battery compartment.
Insert the negative (–) end first,
then push in and down until the
positive (+) end clicks into
position.
Using the remote
commander
You can use this remote
commander to operate this DVDVCR and a Sony TV. Buttons on
the remote commander marked
with a dot (•) can be used to
operate your Sony TV.
If the TV does not have the
symbol near the remote sensor, this
remote commander will not
operate the TV.
Remote sensor
TV /
DVD·VIDEO
SELECT
VIDEO
SELECT
DVD
To operate
Set TV / DVD·VIDEO to
the DVD player
DVD·VIDEO, then press SELECT DVD and point at the remote sensor at
the DVD-VCR
the VCR
DVD·VIDEO, then press SELECT VIDEO and point at the remote sensor
at the DVD-VCR
your TV
TV and point at the remote sensor at your TV
Notes
• With normal use, the batteries should last about three to six months.
• If you do not use the remote commander for an extended period of time, remove the batteries
to avoid possible damage from battery leakage.
• Do not use a new battery with an old one.
• Do not use different types of batteries.
• Do not leave the remote commander in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or lighting apparatus. Doing so
may cause a malfunction.
continued
Setting up the remote commander
9
Controlling other TVs with the remote commander
The remote commander is preprogrammed to control non-Sony TVs. If your TV is
listed in the following table, set the appropriate manufacturer’s code number.
1 Set TV / DVD·VIDEO at the top of the remote commander to TV.
down ?/1, and enter your TV’s code number using the number buttons.
2 Hold
Then release ?/1.
Now you can use the ?/1, VOL +/–, PROG +/–, MUTING*, TV/VIDEO, 0-9 and
-/--* buttons to control your TV. You can also use the buttons marked with a dot (•) to
control a Sony TV. To control the DVD-VCR, reset TV / DVD·VIDEO to
DVD·VIDEO.
* for Sony TV only
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until you find
the one that works with your TV.
Manufacturer
Code number
Manufacturer
Code number
Sony
01, 02
Panasonic
17, 49
Akai
68
Philips
06, 07, 08
Ferguson
52
Saba
12, 13
Grundig
10, 11
Samsung
22, 23
Hitachi
24
Sanyo
25
JVC
33
Sharp
29
Loewe
45
Telefunken
36
Mivar
09, 70
Thomson
43
NEC
66
Toshiba
38
Nokia
15, 16, 69
Notes
• If you enter a new code number, the code number previously entered will be erased.
• If the TV uses a different remote control system from the one programmed to work with the
DVD-VCR, you cannot control your TV with the remote commander.
• When you replace the batteries of the remote commander, the code number may change. Set
the appropriate code number every time you replace the batteries.
10
Setting up the remote commander
Step 3 : Connecting the DVD-VCR
If your TV has a Scart (EURO-AV) connector, see page 12.
If your TV does not have a Scart (EURO-AV) connector
Getting Started
Note that “Advanced Hookups” (page 52) explains additional hookup methods that
will optimize the picture and sound for a true “hometheatre” experience.
Mains lead
to mains
AERIAL IN
Aerial cable (supplied)
: Signal flow
1
Disconnect the aerial cable from your TV
and connect it to
on the rear panel of the
DVD-VCR.
2
Connect
of the DVD-VCR and the
aerial input of your TV using the supplied
aerial cable.
3
Connect the mains lead to the mains.
Note
• When you connect the DVD-VCR and your TV only with an aerial cable, you have to tune
your TV to the DVD-VCR (see page 14).
continued
Connecting the DVD-VCR
11
If your TV has a Scart (EURO-AV) connector
Mains lead
AERIAL IN
Scart
(EURO-AV)
: Signal flow
to mains
Aerial cable (supplied)
Scart cable (not supplied)
1
Disconnect the aerial cable from your
TV and connect it to
on the rear
panel of the DVD-VCR.
2
Connect
of the DVD-VCR and the
aerial input of your TV using the
supplied aerial cable.
3
Connect LINE-1 (EURO AV) on the
DVD-VCR and the Scart (EURO-AV)
connector on the TV with the optional
Scart cable.
This connection improves picture and
sound quality.
4
12
Connect the mains lead to the mains.
Connecting the DVD-VCR
LINE-1
(EURO AV)
Additional connections
LINE-3
LINE OUT
Scart cable (not supplied)
Getting Started
To a satellite or digital tuner
with Line Through
Using the Line Through
function, you can watch
programmes from a satellite or
digital tuner connected to this
DVD-VCR on the TV even
when the DVD-VCR is turned
off. When you turn on the
satellite or digital tuner, this
DVD-VCR automatically sends
the signal from the satellite or
digital tuner to the TV without
turning itself on.
: Signal flow
1 Connect the satellite or digital tuner to the LINE-3 connector as shown above.
off the DVD-VCR.
2 Turn
To watch a programme, turn on the satellite or digital tuner and the TV.
Notes
• This function may not work with some types of satellite or digital tuners.
• When the DVD-VCR is turned off, set the TV to the video channel.
• The Line Through function will not operate properly if “Power Save” in “OPTION” menu is
set to “On.” Set “Power Save” to “Off” to ensure proper operation.
Connecting the DVD-VCR
13
Step 4 : Setting up the DVD-VCR with the
Auto Set Up function
Before using the DVD-VCR for the first
time, set up the DVD-VCR using the Auto
Set Up function. With this function, you can
set TV channels, guide channels for the
VIDEO Plus+ system, and DVD-VCR clock
automatically.
SET UP
Before you start…
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
V/v/B/b
ENTER
1
Turn on your TV and set it to the video channel.
2
Connect the mains lead to the mains.
If your TV does not have a Scart (EURO-AV) connector, tune the TV to
channel 21 (the initial RF channel for this DVD-VCR). Refer to your TV
manual for TV tuning instructions. If the picture does not appear clearly,
see “To change the RF channel” on page 15.
The DVD-VCR automatically turns on and the
DVD-VCR starts searching for all of the
receivable channels and presets them (in the
appropriate order for your local area).
If you want to change the order of the channels
or disable unwanted programme positions, see
“Changing/disabling programme positions” on
page 21.
AUTO SETUP
Please wait
RETURN
10%
SET UP
After the search is complete, the current time appears for any stations that
transmit a time signal. If the time does not appear, set the clock manually.
See “Setting the clock” on page 17.
14
Setting up the DVD-VCR with the Auto Set Up function
To cancel the Auto Set Up function
Press SET UP.
Tip
• If you want to change the language for the on-screen display from the one preset in the Auto
Set Up function, see page 16.
Getting Started
To change the RF channel
If the picture does not appear clearly on the TV, change the RF channel on the DVDVCR and TV. Select “Install” in the “OPTION” menu, then press V/v to select
“Video Output CH.” Select the RF channel by pressing the B/b buttons and press
ENTER. Then, tune the TV to the new RF channel so that a clear picture appears.
Notes
• Whenever you operate the Auto Set Up function, some of the settings (VIDEO Plus+, timer,
etc.) will be reset. If this happens, you have to set them again.
• Auto preset starts automatically only when you plug in the mains lead for the first time after
you purchase the DVD-VCR.
• If you want to use the Auto Set Up function again, select “Install” in the “OPTION” menu,
then press V/v to select “Auto Setup.”
• Auto preset can be performed by pressing x on the unit continuously for 5 seconds or more
during power off with no tape inserted.
Setting up the DVD-VCR with the Auto Set Up function
15
Step 5 : Selecting a language
You can change the on-screen display
language.
SET UP
Before you start…
• Turn on the DVD-VCR and your TV.
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
1
SET UP
Press SET UP, then press V/v to select
(OPTION) and press ENTER.
ENTER
2
V/v
ENTER
OPTION
Language :English
Clock
Install
User Set
[ Off ]
Auto Power Off
[ On ]
Screen Messages
Power Save
[ Off ]
V v
Press V/v to select “Language,” then press
ENTER.
The “LANGUAGE SET” menu appears.
V v
4
16
SET UP
Selecting a language
Press SET UP to exit the menu.
SET UP
English
Français
Deutsch
Español
Italiano
Nederlands
ENTER
Press V/v to select the desired language, then press ENTER.
ENTER
RETURN
LANGUAGE SET
B
ENTER
3
ENTER
RETURN
SET UP
Step 6 : Setting the clock
The Auto Clock Set function works only if a
station in your area is broadcasting a time
signal.
SET UP
Before you start…
• Turn on the DVD-VCR and your TV.
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
1
SET UP
2
V/v/B/b
ENTER
Press SET UP, then press V/v to select
(OPTION) and press ENTER.
ENTER
OPTION
Language :English
Clock
Install
User Set
[ Off ]
Auto Power Off
[ On ]
Screen Messages
Power Save
[ Off ]
V v
ENTER
Press V/v to select “Clock,” then press
ENTER.
ENTER
The “CLOCK SET” menu appears.
SET UP
Time Date
Year
12:00 1/JAN /2004 THU
Auto Clock
[ On ]
Press V/v to set the hour.
ENTER
RETURN
CLOCK SET
V v B b ENTER
3
Getting Started
You must set the time and date on the DVDVCR to use the timer features properly.
RETURN
SET UP
CLOCK SET
Time Date
Year
18:00 1/JAN /2004 THU
Auto Clock
[ On ]
V v B b ENTER
RETURN
SET UP
continued
Setting the clock
17
4
Press b to select the minutes and set the
minutes by pressing V/v.
CLOCK SET
Time Date
Year
18:30 1/JAN /2004 THU
Auto Clock
[ On ]
ENTER
V v B b ENTER
5
ENTER
Set the day, month, and year in sequence by
pressing b to select the item to be set, and
press V/v to select the digits, then press b.
The day of the week is set automatically.
Press b to select “Auto Clock.”
6
The DVD-VCR automatically sets the clock
according to the time signal broadcast between
the channels PR 1 to PR 5.
If you do not need the Auto Clock Set function,
select “Off.”
7
SET UP
CLOCK SET
Time Date
Year
18:30 28/SEP /2004 TUE
Auto Clock
[ On ]
V v B b ENTER
Press V/v to select “On” for the setting of the
Auto Clock Set function.
ENTER
RETURN
RETURN
SET UP
CLOCK SET
Year
Time Date
18:30 28/SEP /2004 TUE
Auto Clock
[ On ]
V v B b ENTER
RETURN
SET UP
Press ENTER to confirm the setting.
ENTER
8
SET UP
Press SET UP to exit the menu.
Tips
• If you set “Auto Clock” to “On,” the Auto Clock Set function is activated whenever the DVDVCR is turned off. The time is adjusted automatically by making reference to the time signal
from the station.
• To change the digits while setting, press B to return to the item to be changed, and select the
digits by pressing V/v.
Note
• The clock display appears when VIDEO mode is selected with no tape inserted or when the
DVD-VCR is turned off.
18
Setting the clock
Step 7 : Presetting channels
SET UP
Before you start…
• Turn on the DVD-VCR and your TV.
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
1
SET UP
2
V/v/B/b
ENTER
O RETURN
Press SET UP, then press V/v to select
(OPTION) and press ENTER.
ENTER
OPTION
Language :English
Clock
Install
User Set
[ Off ]
Auto Power Off
[ On ]
Screen Messages
Power Save
[ Off ]
V v
Press V/v to select “Install,” then press
ENTER.
V v
ENTER
RETURN
SET UP
INSTALL
The “INSTALL” menu appears.
Press V/v to select “Manual Setup,” then
press ENTER.
ENTER
Auto Setup
Manual Setup
Video Output CH
ENTER
3
Getting Started
If some channels could not be preset using
the Auto Set Up function, you can preset
them manually.
ENTER
RETURN
[ CH21 ]
SET UP
TV STATION TABLE
PR
1
2
3
4
5
vV B
RETURN
CH
27
29
30
32
NAME
AAB –
LMN –
CDE –
IJK–
SWAPPING : ENTER
DELETE : CLEAR
continued
Presetting channels
19
4
Press V/v to select the row which you want to
preset, then press b.
ENTER
To display other pages for programme
positions 6 to 80, press V/v repeatedly.
MANUAL TUNING
PR
CH
MFT
NAME
:
:
:
:
MEMORY : ENTER
vVb B
RETURN
5
Press B/b repeatedly until the channel you
want is displayed.
ENTER
MANUAL TUNING
PR
CH
MFT
NAME
:
:
:
:
Press V/v to select “NAME,” then press b.
MANUAL TUNING
PR
CH
MFT
NAME
ENTER
:
:
:
:
Enter the station name.
ENTER
1 Press V/v to select a character.
Each time you press V, the character
changes as shown below.
AtBt…tZt0t1t…t9
tA
5
33
–
––––
MEMORY : ENTER
vVb B
RETURN
7
5
–––
–
––––
MEMORY : ENTER
vVb B
RETURN
6
5
–––
–
––––
MANUAL TUNING
PR
CH
MFT
NAME
vVb B
RETURN
:
:
:
:
5
33
–
O–––
MEMORY : ENTER
2 Press b to set the next character.
The next space flashes.
To correct a character, press B/b until the character you want to correct
flashes, then reset it.
You can set up to 4 characters for the station name.
8
Press ENTER to confirm the station name.
ENTER
9
Press O RETURN, then press SET UP to exit the menu.
RETURN
SET UP
20
Presetting channels
If the picture is not clear
If the picture is not clear, you may use the Manual Fine Tuning (MFT) function.
After step 5, press V/v to select “MFT.” Press B/b to get a clear picture. Then
press ENTER.
Note
• When adjusting MFT, the menu may become difficult to read due to interference from the
picture being received.
Changing/disabling programme positions
Getting Started
Tip
• The DVD-VCR must receive channel information for station names to appear automatically.
After setting the channels, you can change
the programme positions as you like. If any
programme positions are unused or contain
unwanted channels, you can disable them.
You can also change the station names. If the
station names are not displayed, you can
enter them manually.
Changing programme
positions
SET UP
Before you start…
• Turn on the DVD-VCR and your TV.
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
O RETURN
V/v
ENTER
1
SET UP
ENTER
Press SET UP, then press V/v to select
(OPTION) and press ENTER.
OPTION
Language :English
Clock
Install
User Set
[ Off ]
Auto Power Off
[ On ]
Screen Messages
Power Save
[ Off ]
V v
ENTER
RETURN
SET UP
continued
Presetting channels
21
2
Press V/v to select “Install,” then press
ENTER.
INSTALL
Auto Setup
Manual Setup
Video Output CH
ENTER
The “INSTALL” menu appears.
V v
3
Press V/v to select “Manual Setup,” then press
ENTER.
ENTER
ENTER
Press V/v to select the row containing the
programme position you want to change.
ENTER
To display other pages for programme
positions 6 to 80, press V/v repeatedly.
CH
27
29
30
32
Press ENTER, then press V/v to move to the
desired programme position.
ENTER
TV STATION TABLE
PR
1
2
3
4
5
CH
27
29
30
32
TV STATION TABLE
PR
1
2
3
4
5
CH
27
NAME
AAB –
30
32
29
CDE –
IJK–
LMN –
SWAPPING : ENTER
Press ENTER to confirm the setting.
ENTER
7
To change the programme position of another station, repeat steps 4 through 6.
Press O RETURN, then press SET UP to exit the menu.
RETURN
SET UP
22
NAME
AAB –
LMN –
CDE –
IJK–
SWAPPING : ENTER
DELETE : CLEAR
vV B
RETURN
6
NAME
AAB –
LMN –
CDE –
IJK–
SWAPPING : ENTER
DELETE : CLEAR
vV B
RETURN
5
SET UP
TV STATION TABLE
PR
1
2
3
4
5
vV B
RETURN
4
RETURN
[ CH21 ]
Presetting channels
Disabling unwanted programme positions
After presetting channels, you can disable
unused programme positions. The disabled
positions will be skipped later when you
press the PROG +/– buttons.
Getting Started
Before you start…
• Turn on the DVD-VCR and your TV.
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
CLEAR
SET UP
O RETURN
V/v
ENTER
1
SET UP
Press SET UP, then press V/v to select
(OPTION) and press ENTER.
ENTER
2
OPTION
Language :English
Clock
Install
User Set
[ Off ]
Auto Power Off
[ On ]
Screen Messages
Power Save
[ Off ]
V v
Press V/v to select “Install,” then press
ENTER.
ENTER
RETURN
SET UP
INSTALL
Auto Setup
Manual Setup
Video Output CH
ENTER
The “INSTALL” menu appears.
V v
ENTER
RETURN
[ CH21 ]
SET UP
continued
Presetting channels
23
3
Press V/v to select “Manual Setup,” then press
ENTER.
ENTER
TV STATION TABLE
PR
1
2
3
4
5
CH
27
29
30
32
vV B
RETURN
4
Press V/v to select the row which you want to
disable.
ENTER
To display other pages for programme
positions 6 to 80, press V/v repeatedly.
SWAPPING : ENTER
DELETE : CLEAR
TV STATION TABLE
PR
1
2
3
4
5
CH
27
29
30
32
vV B
RETURN
5
CLEAR
NAME
AAB –
LMN –
CDE –
IJK–
SWAPPING : ENTER
DELETE : CLEAR
Press CLEAR.
The selected row will be cleared as shown on
the right.
NAME
AAB –
LMN –
CDE –
IJK–
TV STATION TABLE
PR
1
2
3
4
5
CH
27
NAME
AAB –
30
32
CDE –
IJK–
vV B
RETURN
SWAPPING : ENTER
DELETE : CLEAR
6
Repeat steps 4 and 5 for any other programme positions you want to
disable.
7
Press O RETURN, then press SET UP to exit the menu.
RETURN
SET UP
Note
• Be sure to select the programme position you want to disable correctly. If you disable a
programme position by mistake, you need to reset that channel manually.
24
Presetting channels
Changing the station names
You can change or enter the station names
(up to 4 characters). The DVD-VCR must
receive channel information for station
names to appear automatically.
SET UP
Getting Started
Before you start…
• Turn on the DVD-VCR and your TV.
• To control the DVD-VCR, set TV /
DVD·VIDEO to DVD·VIDEO on the
remote (page 9).
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
1
SET UP
O RETURN
Press SET UP, then press V/v to select
(OPTION) and press ENTER.
OPTION
:English
Language
Clock
Install
User Set
Auto Power Off
Screen Messages
Power Save
V v
ENTER
2
V/v/B/b
ENTER
ENTER
RETURN
Press V/v to select “Install,” then press
ENTER.
The “INSTALL” menu appears.
V v
Press V/v to select “Manual Setup,” then press
ENTER.
ENTER
SET UP
INSTALL
Auto Setup
Manual Setup
Video Output CH
ENTER
3
[ Off ]
[ On ]
[ Off ]
ENTER
RETURN
[ CH21 ]
SET UP
TV STATION TABLE
PR
1
2
3
4
5
vV B
RETURN
CH
27
29
30
32
33
NAME
AAB –
LMN –
CDE –
IJK–
SWAPPING : ENTER
DELETE : CLEAR
continued
Presetting channels
25
4
Press V/v to select the row which you want to
change or enter the station name, then press b.
ENTER
To display other pages for programme
positions 6 to 80, press v/V repeatedly.
MANUAL TUNING
PR
CH
MFT
NAME
:
:
:
:
MEMORY : ENTER
vVb B
RETURN
5
Press V/v to select “NAME,” then press b.
MANUAL TUNING
PR
CH
MFT
NAME
ENTER
:
:
:
:
Enter the station name.
ENTER
1 Press V/v to select a character.
Each time you press V, the character
changes as shown below.
AtBt…tZt0t1t…t9
tA
5
33
–
––––
MEMORY : ENTER
vVb B
RETURN
6
5
33
–
––––
MANUAL TUNING
PR
CH
MFT
NAME
vVb B
RETURN
:
:
:
:
5
33
–
O–––
MEMORY : ENTER
2 Press b to set the next character.
The next space flashes.
To correct a character, press B/b until the character you want to correct
flashes, then reset it.
You can set up to 4 characters for the station name.
7
Press ENTER to confirm the new name.
ENTER
8
Press O RETURN, then press SET UP to exit the menu.
RETURN
SET UP
26
Presetting channels
Basic Operations
Playing discs
Depending on the disc, some operations may
be different or restricted. Refer to the
operating instructions supplied with your
disc.
Before you start...
• Turn on the DVD-VCR and your TV.
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• Set TV / DVD·VIDEO to DVD·VIDEO,
then press SELECT DVD to control the
DVD player (page 9).
?/1
Z
/
m/M y
1
Basic Operations
./>
X
x
H
Press Z to open the disc tray and
place a disc on the disc tray.
with the playback side
facing down
continued
Playing discs
27
2
Press H.
The disc tray closes and the DVD player starts playback.
The display window shows the
playback time.*
Depending on the disc, a menu
may appear on the TV screen.
For DVDs, see page 66. For
VIDEO CDs, see page 88.
Hour Minute Second
* “– – – – –” appears when no disc
is loaded.
Additional tasks
To
Press
x
Stop play
Pause play*
1
Resume play after pause
X
H
Go to the next frame in pause mode
SKIP
Go to the previous frame in pause
mode
REPLAY
Go to the next chapter, track, or scene
in continuous play mode
> NEXT on the remote or M on the unit
Go back to the previous chapter, track,
or scene in continuous play mode
. PREV on the remote or m on the unit
Replay the previous scene for 10
seconds in continuous play mode*2
(Instant Replay)
REPLAY
Briefly fast forward the current scene
for 30 seconds in continuous play
mode*2*3
(Instant Advance)
SKIP
Stop play and remove the disc
Z
1
* If you pause the DVD player for more than 5 minutes, the DVD player will automatically
stop.
*2 For DVD VIDEOs and the DVD-RWs/DVD-Rs or DVD+RWs/DVD+Rs only
*3 You can press
SKIP up to 4 times. This allows you to fast forward up to 2 minutes in
total.
Tips
• The Instant Replay function is useful when you want to review a scene or dialogue that you
missed.
• The Instant Advance function is useful when you want to pass over a scene that you don’t
want to watch.
28
Playing discs
Notes
• You may not be able to use the Instant Replay or Instant Advance function with some scenes.
• Switching between original (ORG) and play list (PL) within a disc recorded in VR mode is
possible only while the disc is stopped. Press TOP MENU to switch between ORG and PL.
To Resume playback for the current disc (Resume Play)
The DVD player remembers the point where you stopped the disc even if the DVD
player enters standby mode by pressing ?/1.
1 While playing a disc, press x to stop playback.
H.
2 Press
The DVD player starts playback from the point where you stopped the disc in
Step 1.
Tip
• To begin playback from the top of the disc, press x twice then press H.
• DVD:
PLAY t FF1/FR1 t FF2/FR2 t FF3/FR3 t FF4/FR4 t FF5/FR5 t
FF6/FR6
• CD, MP3 and VIDEO CD:
PLAY t FF1/FR1 t FF2/FR2 t FF3/FR3
When you find the point you want, press H.
Basic Operations
To locate a point quickly by playing a disc in fast forward or fast reverse
in continuous play mode
Press m or M on the remote (or hold down m or M on the unit).
Each time you press the button, the playback speed changes as follows.
Note
• The fast reverse operation may not be possible for CD, MP3 and VIDEO CD depending on
the recording method.
To watch slow motion in continuous play mode (DVD and VIDEO CD
only)
Press X, then press
cyclically as follows.
or y. With each press, the playback speed changes
* You can not watch reverse slow motion with DVD-RW in VR mode. Reverse slow motion
playback also may not be possible for some VIDEO CDs depending on the recording
method.
To resume normal playback, press H.
Tips
• To make a video timer reservation during DVD playback, we recommend performing the
operations under “Quick Timer Recording” (page 90).
• During DVD playback, DVD-VCR does not standby even if the VCR stops recording.
continued
Playing discs
29
Notes
• You can change the screen type using the “SCREEN SETUP” menu. (See “Screen Setup” on
page 58.)
• Do not perform VIDEO playback while playing back a disc.
• If you play a DVD or VIDEO CD that has scratches, the player may stop playback at the
point of the scratch.
• Except for during normal play or FF1 play, no sound is output.
• Discs recorded in VR mode with Once Copy signal cannot be played because of copyright
protection.
• Playback of play lists longer than 10 hours recorded in VR mode is not guaranteed.
Notes on playing DTS* sound tracks on a CD
• When playing DTS-encoded CDs, no audio out will be output from the analogue stereo jacks.
To avoid possible damage to the audio system, the consumer should take proper precautions
when the analogue stereo jacks of the DVD player are connected to an amplification system.
• Do not play DTS sound tracks without first connecting the DVD player to an audio
component having a built-in DTS decoder. The DVD player outputs the DTS signal via the
DIGITAL AUDIO OUT (COAXIAL or OPTICAL) jack even if “DTS” is set to “Off” in
“AUDIO SETUP” menu (page 56), and may affect your ears or cause your speakers to be
damaged.
Notes on playing DVDs with a DTS sound track
• DTS audio signals are output only through the DIGITAL AUDIO OUT (COAXIAL or
OPTICAL) jack.
• When you play a DVD with DTS sound tracks, set “DTS” to “On” in “AUDIO SETUP”
menu (page 56). You cannot select DTS audio stream when “DTS” is set to “Off”.
• If you connect the player to audio equipment without a DTS decoder, do not set “DTS” to
“On” in “AUDIO SETUP” menu (page 56). A loud noise may come out from the speakers,
affecting your ears or causing the speakers to be damaged.
* “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
30
Playing discs
Guide to the on-screen display
You can check disc information during
playback.
The displayed contents differ according to
the type of disc being played.
Number
buttons
Basic Operations
V/v/B/b
ENTER
O RETURN
DISPLAY
Press DISPLAY during playback. The following information appears; type of disc,
current title/track, chapter, counter position, voice language, subtitle language and
Custom AV Mode setting. Refer to “DVD Audio/Subtitle Language” on page 119 for
the abbreviation of the language.
Type of disc
Current title/track number
Current chapter number
Counter position
Voice language
Subtitle language
Custom AV Mode
N
1/3
1/36
T 0:01:09
ENG 5.1CH
ENG (3/5)
Standard
V v B b 0 ~ 9
ENTER
Note
• You cannot select disc information items when the disc is stopped.
continued
Guide to the on-screen display
31
To playback the desired title/track or chapter
You can playback the desired title/track or chapter using
this menu.
1 Press V/v during playback to select the desired item.
2 Press B/b to change the item.
3 Press ENTER to start playback.
DISPLAY or O RETURN to turn off the
4 Press
menu.
N
1/3
1/36
T 0:01:09
ENG 5.1CH
ENG (3/5)
Standard
V v B b 0 ~ 9
ENTER
The title/track or chapter icon will appear on the DVD playback screen followed by
the current title/track or chapter number and the counter position.
To playback from the desired title/track counter position
You can playback the desired title/track counter position
using this menu.
Press V/v during playback to select the counter
1 position
icon.
Enter the desired elapsed playing time of the current
2 title/track using the number buttons.
3 Press ENTER to start playback.
DISPLAY or O RETURN to turn off the
4 Press
menu.
N
1/3
1/36
T 0:01:09
ENG 5.1CH
ENG (3/5)
Standard
V v B b 0 ~ 9
ENTER
Tip
• You can change the counter position information (playing time or remaining time) using
B/b (DVD and CD only).
DVD
Indication
Counter information
T ∗ : ∗∗ : ∗∗
Elapsed playing time of the current title
T– ∗ : ∗∗ : ∗∗
Remaining time of the current title
C ∗ : ∗∗ : ∗∗
Elapsed playing time of the current chapter
C– ∗ : ∗∗ : ∗∗
Remaining time of the current chapter
CD
32
Indication
Counter information
T ∗ : ∗∗ : ∗∗
Elapsed playing time of the current track
T– ∗ : ∗∗ : ∗∗
Remaining time of the current track
D ∗ : ∗∗ : ∗∗
Elapsed playing time of the disc
D– ∗ : ∗∗ : ∗∗
Remaining time of the disc
Guide to the on-screen display
Notes
• The display may not change as operated depending on the disc.
• The display window continue indicating the playing time even when the counter position
information on the on-screen display is being changed.
• The remaining time of the current track and the disc may not be indicated correctly for Copy
Control CDs, CD EXTRA or CDs with jacket pictures on the disc, etc.
To adjust the playback picture (Custom AV Mode)
You can adjust the video signal of the DVD or VIDEO CD (with PBC function off)
from the player to obtain the picture quality you want. Choose the setting that best
suits the programme you are watching.
Press V/v during playback to select the Custom AV
N
1/3
Mode icon.
1
1/36
T 0:01:09
ENG 5.1CH
ENG (3/5)
Standard
V v B b 0 ~ 9
ENTER
Setting
Video Setting
Audio Setting
Dynamic 2
Produces a more dynamic
picture than Dynamic 1 by
further increasing the picture
contrast and the colour intensity.
Full (modulated) sound with
even clearer treble and bass than
Dynamic 1.
Dynamic 1
Produces a bold dynamic picture
by increasing the picture contrast
and the colour intensity.
Full (modulated) sound with
clear treble and bass.
Standard
Off (Default setting)
Displays a standard picture.
Standard sound.
Cinema 1
White colours become brighter
and black colours become richer,
and the colour contrast is
increased.
Powerful sound with strong bass.
Cinema 2
Enhances details in dark areas by
increasing the black level.
Powerful sound with even
stronger bass than Cinema 1.
Basic Operations
2 Press B/b to change the setting.
Tip
• When you watch a movie, “Cinema 1” or “Cinema 2” is recommended.
Guide to the on-screen display
33
Locking the disc tray (Child Lock)
You can lock the disc tray so that the disc tray
is not opened by mistake.
SELECT DVD
Xx
To lock the disc tray
When the DVD-VCR is turned on, press x, X and SELECT DVD on the unit at the
same time. “LOCK” appears in the display window. The disc tray is locked.
To unlock the disc tray
Press x, X and SELECT DVD on the unit at the same time. The disc tray is
unlocked.
Notes
• If you lock the disc tray while open, the disc tray will be locked after closing.
• You cannot lock the disc tray when the DVD-VCR is turned off. If the DVD-VCR is turned
on, you can lock the disc tray either in play mode or stop mode.
34
Locking the disc tray (Child Lock)
Playing a tape
Before you start...
• Turn on the DVD-VCR and your TV.
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• Set TV / DVD·VIDEO to DVD·VIDEO,
then press SELECT VIDEO to control the
VCR (page 9).
?/1
Z
TRACKING +/–
CLEAR
/
m/M y
Basic Operations
./>
X
x
H
DISPLAY
1
Insert a tape.
2
Press H.
The VCR starts playing automatically if
you insert a tape with its safety tab
removed.
The display window shows the
playback time.
When the tape reaches the end,
it will rewind automatically.
Hour Minute Second
continued
Playing a tape
35
Additional tasks
To
Press
Stop play
x
Pause play∗
X
Resume play after pause
X or H
Fast-forward the tape
M during stop
Rewind the tape
m during stop
Eject the tape
Z
* If you pause the VCR for more than 5 minutes, the VCR will automatically resume play.
To turn off the power while rewinding (Rewind Shut Off)
Press ?/1 while the tape is rewinding. The power will turn off, but the tape will keep
rewinding until it reaches the end.
To play/search at various speeds
Playback options
Operation
View the picture during fastforward or rewind
During fast-forward, hold down M. During rewind, hold
down m.
Play at high speed
• During playback, briefly press M or m. The tape
continues to play at 5 times normal speed.
• During playback, hold down M or m. The tape
continues to play at 5 times normal speed. When you
release the button, normal playback resumes.
Play in slow motion*1
During pause, press y.
Replay the previous scene in
continuous play mode*2
(Instant Replay)
During playback, press
REPLAY.
Fast forward the current scene
for 30 seconds in continuous
play mode*3
(Instant Skip)
During playback, press
SKIP.
Play at various speeds
(Shuttle play)
During playback, press .or >. You can change the
playback speed as follows.
REW*4 y –PLAY2 y –PLAY y –SLOW y STILL
y SLOW y PLAY y PLAY2 y FF*5
*1 You can change the slow motion playback speed by pressing M or m.
*2 For 10 seconds in SP or LP mode/for 15 seconds in EP mode
*3 You can press
SKIP up to 4 times. This allows you to fast forward up to 2 minutes in
total.
*4 “REW” flashes in the display window.
*5 “FF” flashes in the display window.
36
Playing a tape
To play a recently watched scene
You can immediately rewind and playback the scene you want to watch again.
During playback, press
REPLAY (see “To play/search at various speeds” above).
To skip playback
You can skip a scene that you do not want to watch and restart playback.
During playback, press
SKIP (see “To play/search at various speeds” above).
To resume normal playback
Press H.
To set the colour system
If the playback picture has no colour, or streaks appear during playback, set “Colour
System” in the “USER SET” menu to conform to the system that the tape was
recorded in (see page 103). (Normally set the option to “Auto.”)
Basic Operations
To use the time counter
Press CLEAR at the point on the tape that you want to find later. The counter in the
display window resets to “0:00:00.”
To display the counter on the TV screen, press DISPLAY during normal playback.
Tip
• Adjust the picture using the TRACKING +/– buttons if:
– Streaks appear while playing in slow motion.
– Bands appear at the top or bottom while pausing.
– The picture shakes during pause.
continued
Playing a tape
37
Notes
• Tapes recorded in the LP mode on other VCRs can be played back on this VCR but the
picture quality cannot be guaranteed.
• The counter resets to “0:00:00” whenever a tape is reinserted.
• The counter stops counting when it comes to a portion with no recording.
• Depending on your TV, the following may occur while playing an NTSC-recorded tape:
– The picture becomes black and white.
– The picture shakes.
– No picture appears on the TV screen.
– Black streaks appear horizontally on the TV screen.
– The colour density increases or decreases.
• When 10 hours have passed, the counter in the display window returns to “0:00:00” and the
count starts over again.
• The sound is muted during playback at various speeds.
• The picture may show noise when playing at high speed in reverse.
• While playing a tape, you can display the setup menu, but the remote commander’s function
switches to DVD automatically. Press SET UP to exit the menu.
• Stop disc playback while playing back a video.
• The picture returns to normal playback from slow motion in reverse in 30 seconds.
38
Playing a tape
Recording TV programmes
Before you start...
• Turn on the DVD-VCR and your TV.
• Switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
• Set TV / DVD·VIDEO to DVD·VIDEO,
then press SELECT VIDEO to control the
VCR (page 9).
• To record from a satellite or digital tuner,
turn it on.
• Make sure the tape is longer than the total
recording time.
Z
SELECT DVD
PROG +/–
Number
buttons
-/-INPUT
SELECT
SP/LP
x
H
Basic Operations
z REC
DISPLAY
1
Insert a tape with its safety tab in place.
continued
Recording TV programmes
39
2
• PROG/
TRACKING
• To record a normal channel, press PROG +/– until the programme
position number you want appears in the display window.
INPUT
SELECT
• To record from other equipment connected to one or more of the LINE
inputs, press INPUT SELECT until the connected line appears in the
display window.
3
SP / LP
4
REC
Press SP/LP to select the tape speed, SP or LP.
LP (Long Play) provides recording time twice as long as SP. However, SP
(Standard Play) produces better picture and audio quality.
Press z REC to start recording.
The recording indicator lights up red in the display window.
Recording indicator
To stop recording
Press x.
40
Recording TV programmes
To check the remaining time
Press DISPLAY three times. With the display on, press DISPLAY again to check the
remaining time.
STEREO
PAL
AUTO
PR 1
BBC 1
SP
REMAIN
0 :00 :22
1 :46
Time counter
Remaining tape length
In order to get an accurate remaining time indication, be sure “Tape Select” in the
“VIDEO SETUP” menu is set according to the tape type you use (see page 98).
Maximum Recording Time
SP
LP
E-180
3 hrs
6 hrs
E-240
4 hrs
8 hrs
E-260
4 hrs 20 mins
8 hrs 40 mins
E-300
5 hrs
10 hrs
To watch another TV programme while recording
Basic Operations
Tape Length
your TV is connected to the VCR using A/V connections, set the TV to the
1 IfTV’s
antenna input; if not, skip this step.
Select another channel on the TV.
2
To watch a DVD while recording
1 Press SELECT DVD to control the DVD player.
2 Press Z and place the disc on the disc tray.
H.
3 Press
The disc tray closes and the DVD player starts playback. The TV screen will
automatically change to the DVD playback screen.
continued
Recording TV programmes
41
To save a recording
To prevent accidental erasure, break
off the safety tab as illustrated. To
record on the tape again, cover the tab
hole with adhesive tape.
Safety tab
Tips
• To select a programme position, you can use the number buttons on the remote commander.
For two-digit numbers, press -/-- (ten’s digit) followed by the number buttons.
• If you connect additional equipment to a LINE connector or jack, you can select the input
signal using the INPUT SELECT or PROG +/– buttons.
• The display appears on the TV screen indicating information about the tape, but the
information will not be recorded on the tape.
• If you do not want to watch TV while recording, you can turn off the TV. When using a
satellite or digital tuner, make sure to leave it on.
Notes
• If a tape has portions recorded in both PAL and NTSC systems, the time counter reading will
not be correct. This discrepancy is due to the difference between the counting cycles of the
two video systems.
• The remaining tape length may not be indicated accurately for short tapes such as T-20 or
T-30, or tapes recorded in LP mode.
• The remaining time is intended for rough measurement only.
• About 30 seconds after the tape begins playback, the tape remaining time will be displayed.
• You cannot record a DVD to a VCR tape.
• To watch a TV programme during video recording, stop disc playback.
42
Recording TV programmes
Recording TV programmes using the
VIDEO Plus+® system
The VIDEO Plus+ system is the feature that
simplifies programming the VCR to make
timer recordings. Just enter the PlusCode
number listed in the TV programme guide.
The date, times, and programme position of
that programme are set automatically. You
can preset a total of six programmes,
including settings made with other timer
methods.
?/1
SELECT VIDEO
Number
buttons
Before you start...
• Check that the DVD-VCR clock is set to
the correct time.
• Turn on the DVD-VCR and your TV.
• Set your TV to the video channel so that
the signal from the player appears on the
TV screen.
• Set TV / DVD·VIDEO to DVD·VIDEO,
then press SELECT VIDEO to control the
VCR (page 9).
• When using a satellite or digital tuner, turn
it on.
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
SUBTITLE/
TIMER
INPUT SELECT
TIMER
x
Basic Operations
1
CLEAR
TV/VIDEO
V/v/B/b
ENTER
Press TIMER.
TIMER METHOD
The “TIMER METHOD” menu appears.
Standard
VideoPlus
V v
ENTER
RETURN
SET UP
continued
Recording TV programmes using the VIDEO Plus+® system
43
2
Press V/v to select “VideoPlus,” then press
ENTER.
VideoPlus
ENTER
Code – – – – – – – – –
The “VideoPlus” menu appears.
Code : 0–9
Correct : B
SET UP
RETURN
3
1
2
3
4
5
6
7
8
9
0
CLEAR
Press the number buttons to enter the PlusCode
number.
VideoPlus
Code 1 2 3 4 – – – – –
If you make a mistake, press CLEAR and
re-enter the correct number.
Code : 0–9
Correct : B
You can also press B to delete the last entered
number.
ENTER
RETURN
SET UP
ENTER
4
Press ENTER.
ENTER
INPUT
SELECT
CLEAR
The programme position, date, start and stop
times, tape speed and PDC (Programme
Delivery Control) setting appear on the TV
screen.
PR DATE
35
––
––
––
––
––
SA
––
––
––
––
––
19
––
––
––
––
––
START STOP SPEED PDC
19 : 00
––:––
––:––
––:––
––:––
––:––
V v B b ENTER
20 : 00
––:––
––:––
––:––
––:––
––:––
CLEAR
Off
––
––
––
––
––
SETUP
• If “– –” appears in the “PR” (programme)
column (this may happen for local
broadcasts), you have to set the appropriate programme position
manually.
Press V/v to select the desired programme position. Without setting the
programme position, you cannot select the date, start and stop times, tape
speed and PDC setting.
• To record from other equipment connected to one or more of the LINE
inputs, press INPUT SELECT to display the connected line in the “PR”
position.
You will only have to do this operation once for the referred channel. The
VCR will then store your setting.
If the information is incorrect, press CLEAR to cancel the setting.
44
SP
––
––
––
––
––
Recording TV programmes using the VIDEO Plus+® system
5
If you want to change the date, tape speed and
the PDC setting:
ENTER
1 Press B/b to select the item you want to
change.
2 Press V/v to reset it.
PR DATE
35
––
––
––
––
––
SA
––
––
––
––
––
19
––
––
––
––
––
V v B b
START STOP SPEED PDC
19 : 00
––:––
––:––
––:––
––:––
––:––
20 : 00
––:––
––:––
––:––
––:––
––:––
CLEAR
SP
––
––
––
––
––
Off
––
––
––
––
––
SETUP
ENTER
• To record the same programme every day or
the same day every week, see “Daily/weekly
recording” on page 45.
• To use the PDC function, set “PDC” to “On.” For details about the PDC
function, see “Timer recording with PDC signals” on page 45.
6
Press ENTER to confirm the setting.
ENTER
Basic Operations
7
Press ENTER to confirm all settings.
ENTER
8
Press ?/1 to turn off the DVD-VCR.
The
indicator appears in the display window and the VCR stands by for
recording.
To record from other equipment, leave the connected equipment switched
on.
To stop recording
To stop the DVD-VCR while recording, press SELECT VIDEO and then press x.
Daily/weekly recording
In step 5 above, press v to select the recording pattern. Each time you press v, the
indication changes as shown below. Press V to change the indication in reverse order.
today t DLY (Monday to Sunday) t W-SA (every Saturday) ..... t
W-SU (every Sunday) t 1 month later t (dates count down) t today
Timer recording with PDC signals
Some broadcast systems transmit PDC signals with their TV programmes. These
signals ensure that your timer recordings are made regardless of broadcast delays,
early starts, or broadcast interruptions.
To use the PDC function, set “PDC” to “On” in step 5 above. You can also use the
PDC function for a source connected to one or more of the LINE inputs.
continued
Recording TV programmes using the VIDEO Plus+® system
45
To record satellite broadcasts
If you connect the satellite tuner and the VCR, you can record satellite programmes.
1 Turn on the satellite tuner.
the satellite tuner, select the satellite programme for which you want to make
2 On
a timer setting.
the satellite tuner turned on until the VCR finishes recording the satellite
3 Keep
programme for which you have made a timer setting.
To watch another TV programme after setting the timer
your TV is connected to the VCR using A/V connections, set the TV to the
1 IfTV’s
aerial input; if not, skip this step.
Select another channel on the TV.
2
Tips
• To set the channel, you can also use the V/v or number buttons.
• If the
indicator appears, this means that the VCR is currently recording this programme.
• You can also do the following tasks while the VCR is recording:
– Reset the counter (page 37).
– Display tape information on the TV screen (page 41).
To use the Auto Tape Speed function
In step 5 above, press v to select “Auto.” When you are recording a programme in
the SP mode and the remaining tape length becomes shorter than the recording time,
the recording tape speed is automatically changed to the LP mode. Note that some
noise will appear on the picture when the tape speed is changed. To operate this
function correctly, the “Tape Select” setting in the “VIDEO SETUP” menu must be
accurate (see page 98).
Tips
• To set the line input video source, you can also use the INPUT SELECT button.
• You can set the extended time for the VIDEO Plus+ setting by 10, 20, 30, 40, 50, or 60
minutes. Set “VideoPlus Extend” in the “USER SET” menu to the desired extended time on
page 103.
• To check, change, or cancel the programme setting, see “Checking/changing/cancelling timer
settings” on page 50.
Notes
• If the PDC signal is too weak or the broadcasting station failed to transmit PDC signals, the
VCR will start recording at the set time without using the PDC function.
• The
indicator flashes in the display window when you press ?/1 with no tape inserted.
46
Recording TV programmes using the VIDEO Plus+® system
Recording TV programmes using the timer
You can preset up to six programmes at a
time.
?/1
Before you start…
• Check that the DVD-VCR clock is set to
the correct time.
• Turn on the DVD-VCR and your TV.
• Switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
• Set TV / DVD·VIDEO to DVD·VIDEO,
then press SELECT VIDEO to control the
VCR (page 9).
• When using a satellite or digital tuner, turn
it on.
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
SUBTITLE/
TIMER
Number
buttons
TIMER
Basic Operations
1
SELECT VIDEO
INPUT
SELECT
x
V/v/B/b
ENTER
Press TIMER.
The “TIMER METHOD” menu appears.
TIMER METHOD
Standard
VideoPlus
V v
ENTER
RETURN
SET UP
continued
Recording TV programmes using the timer
47
2
Press V/v to select “Standard,” then press
ENTER.
PR DATE
START STOP SPEED PDC
V v B b
SET UP
PR DATE
START STOP SPEED PDC
V v B b
CLEAR
ENTER
The timer programming menu appears.
3
Set the programme position, date, start and
stop times, tape speed and PDC function:
ENTER
1 Press b to select each item in turn.
2 Press V/v to set each item.
To correct a setting, press B to return to that
setting and reset.
INPUT
SELECT
4
SET UP
• To record the same programme every day or
the same day every week, see “Daily/weekly recording” on page 49.
• To use the PDC function, set “PDC” to “On.” For details about the PDC
function, see “Timer recording with PDC signals” on page 45.
• To record from other equipment connected to one or more of the LINE
inputs, press INPUT SELECT to display the connected line in the “PR”
position.
Press ENTER to confirm the setting.
ENTER
5
To enter another setting, press V/v to select the next row and repeat step 3.
Press ENTER to confirm all settings.
ENTER
6
Press ?/1 to turn off the DVD-VCR.
The
indicator appears in the display window and the VCR stands by for
recording.
To record from other equipment, leave the connected equipment switched
on.
To stop recording
To stop the DVD-VCR while recording, press SELECT VIDEO and then press x.
48
Recording TV programmes using the timer
Daily/weekly recording
In step 3 above, press v to select the recording pattern. Each time you press v, the
indication changes as shown below. Press V to change the indication in reverse order.
today t DLY (Monday to Sunday) t W-SA (every Saturday) ..... t
W-SU (every Sunday) t 1 month later t (dates count down) t today
To use the Auto Tape Speed function
In step 3 above, press v to select “Auto.” When you are recording a programme in
the SP mode and the remaining tape length becomes shorter than the recording time,
the recording tape speed is automatically changed to the LP mode. Note that some
noise will appear on the picture when the tape speed is changed. To operate this
function correctly, the “Tape Select” setting in the “VIDEO SETUP” menu must be
accurate (see page 98).
Notes
• When setting the timer with PDC signals, enter the start times exactly as indicated in the TV
programme guide. Otherwise, the PDC function will not work.
• If the PDC signal is too weak or the broadcasting station failed to transmit PDC signals, the
VCR will start recording at the set time without using the PDC function.
• The
indicator flashes in the display window when you press ?/1 with no tape inserted.
Basic Operations
Tips
• To set the line input video source, you can also use the INPUT SELECT button.
• To check, change, or cancel the programme setting, see “Checking/changing/cancelling timer
settings” on page 50.
To watch another TV programme after setting the timer
your TV is connected to the VCR using A/V connections, set the TV to the
1 IfTV’s
aerial input; if not, skip this step.
Select another channel on the TV.
2
Tips
• To set the channel, you can also use the V/v or number buttons.
• If the
indicator appears, this means that the VCR is currently recording this programme.
• You can also do the following tasks while the VCR is recording:
– Reset the counter (page 37).
– Display tape information on the TV screen (page 41).
Recording TV programmes using the timer
49
Checking/changing/cancelling timer
settings
Before you start…
• Check that the DVD-VCR clock is set to
the correct time.
• Turn on the DVD-VCR and your TV.
• Switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
• Set TV / DVD·VIDEO to DVD·VIDEO,
then press SELECT VIDEO to control the
VCR (page 9).
• When using a satellite or digital tuner, turn
it on.
• Insert a tape with its safety tab in place.
Make sure the tape is longer than the total
recording time.
• If the DVD player is in play mode, you
cannot display the setup menu. Stop the
DVD playback.
CLEAR
SET UP
V/v/B/b
ENTER
1
SET UP
Press SET UP, then press V/v to select
(TIMER) and press ENTER.
The “TIMER METHOD” menu appears.
TIMER METHOD
Standard
VideoPlus
ENTER
V v
2
ENTER
RETURN
SET UP
Press V/v to select “Standard,” then press ENTER.
ENTER
• If you want to change a setting, go on to the next step.
• If you do not need to change the settings, press SET UP to exit the menu.
SET UP
50
Checking/changing/cancelling timer settings
3
Press V/v to select setting you want to change
or cancel.
ENTER
CLEAR
• To change the setting, press B/b to select
the item you want to change, and press V/v
to change it.
• To cancel the setting, press CLEAR.
4
PR DATE
START STOP SPEED PDC
3 5 MO 30 2 0 :0 0 21 : 0 0
2 0 WE 02 2 2 : 0 0 23 : 3 0
6 0 TU 30 2 0 :3 0 22 : 0 0
SP Off
LP Off
Auto Off
V v B b ENTER
SET UP
CLEAR
Press ENTER to confirm the setting.
ENTER
5
Press ENTER to confirm all settings.
ENTER
If any settings remain, turn off the VCR to return to recording standby.
When the timer settings overlap
The programme that starts first has priority and the second programme starts
recording only after the first programme has finished. If the programmes start at the
same time, the programme listed first in the menu has priority.
Programme 1
Basic Operations
To record from other equipment, leave the connected equipment switched
on.
about 20 seconds
Programme 2
will be cut off
Programme 1
Programme 2
about 20 seconds will be cut off
Checking/changing/cancelling timer settings
51
Advanced Hookups
A/V Receiver hookup
A Use this hookup if your A/V receiver has a Dolby* Surround (Pro
Logic) decoder and 3 to 6 speakers
You can enjoy the Dolby Surround effects only when playing Dolby Surround audio
or multi-channel audio (Dolby Digital) discs.
* Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the doubleD symbol are trademarks of Dolby Laboratories.
DVD-VCR
A
Stereo audio cord (supplied)
(red)
R
AUDIO
L
(white)
VIDEO
to OUT AUDIO L/R
(white)
(red)
l: Signal flow
to audio input
[Speakers]
[Speakers]
Amplifier (receiver) with Dolby
Surround decoder
Rear (L)
Rear (R)
Subwoofer
52
A/V Receiver hookup
Front (L)
Centre
Front (R)
B Use this hookup if your A/V receiver has a Dolby Digital, MPEG audio
or DTS* decoder, a digital input jack and 6 speakers
This connection will allow you to use the Dolby Digital, MPEG audio or DTS decoder
function of your AV amplifier (receiver). You are not able to enjoy the surround sound
effects of this player. You must make connections using B-1 and B-2 .
* “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
DVD-VCR
B-1
(red)
B-2
Stereo audio cord
(supplied)
R
DIGITAL
AUDIO OUT
COAXIAL
OPTICAL
AUDIO
L
and
VIDEO
or
to DIGITAL AUDIO OUT
(COAXIAL or OPTICAL)
to OUT AUDIO L/R
Coaxial digital
cord (not
supplied)
l: Signal flow
(white)
Optical digital cord
(not supplied)
Remove jack cap
before connecting
Advanced Hookups
(white)
(red)
to coaxial or optical
digital input
to audio input
[Speakers]
[Speakers]
AV amplifier (receiver) having
a decoder
Rear (L)
Subwoofer
Rear (R)
Front (L)
Centre
Front (R)
Note
• After you have completed the connection, be sure to set “Dolby Digital” to “Dolby Digital”
and “DTS” to “On” in “AUDIO SETUP” menu (page 55). If your AV amplifier (receiver)
has an MPEG audio decoder function, set “MPEG” to “MPEG” in “AUDIO SETUP” menu
(page 55). Otherwise, no sound or a loud noise will come from the speakers.
A/V Receiver hookup
53
S-Video hookup
Make audio connections using the OUT AUDIO L/R jacks or DIGITAL AUDIO OUT
(OPTICAL or COAXIAL) jacks when you use S-VIDEO hookup.
Use this hookup if your TV has an S-VIDEO input jack
Connect an S-VIDEO cord (not supplied). You will enjoy high quality images.
DVD-VCR
l : Signal flow
(DVD only)
TV
or
Audio cord
(supplied)
Coaxial digital
cord (not
supplied)
to audio input
or
S-VIDEO cord
(not supplied)
INPUT
S VIDEO
Optical digital cord
(not supplied)
Remove jack cap
before connecting
to coaxial or optical
digital input
TV or AV amplifier
Notes
• Set “DVD S-Video Out” to “On” in the “SCREEN SETUP” menu (page 58) to view pictures
from the S-VIDEO jack.
• The connection using S-VIDEO OUT jack is only for the DVD player.
54
S-Video hookup
DVD Settings and Adjustments
Audio Setup
“Audio Setup” allows you to set the sound
according to the playback and connection
conditions.
SET UP
V/v/B/b
ENTER
SET UP
Press SET UP when the DVD player is in stop
mode, then press V/v to select
(DVD)
and press ENTER.
ENTER
2
Language Setup
Audio Setup
Screen Setup
Parental Setup
V v
Press V/v to select “Audio Setup,” then press
ENTER.
ENTER
DVD SETUP
RETURN
SET UP
AUDIO SETUP
Dolby Digital
MPEG
DTS
Audio DRC
V v B b
3
ENTER
DVD Settings and Adjustments
1
[ D-PCM ]
[ PCM ]
[ Off ]
[ Standard ]
RETURN
SET UP
Press V/v to select the setup item from the displayed list:
“Dolby Digital,” “MPEG,” “DTS” or “Audio DRC.”
ENTER
continued
Audio Setup
55
4
Press B/b to select an item.
ENTER
5
SET UP
Press SET UP to exit the menu.
Menu choices
• Dolby Digital
Selects the type of Dolby Digital signal.
The default setting is indicated in bold print.
D-PCM
Select this when the player is connected to an audio component
lacking a built-in Dolby Digital decoder.
Dolby Digital
Select this when the player is connected to an audio component
with a built-in Dolby Digital decoder.
• MPEG
Selects the type of MPEG audio signal.
The default setting is indicated in bold print.
PCM
Select this when the player is connected to an audio component
lacking a built-in MPEG decoder. If you play MPEG audio sound
tracks, the player outputs stereo signals via the DIGITAL AUDIO
OUT (OPTICAL or COAXIAL) jack.
MPEG
Select this when the player is connected to an audio component
with a built-in MPEG decoder.
• DTS
Selects whether or not to output DTS signals.
The default setting is indicated in bold print.
56
Audio Setup
Off
Select this when the player is connected to an audio component
lacking a built-in DTS decoder.
On
Select this when the player is connected to an audio component
with a built-in DTS decoder.
• Audio DRC (Dynamic Range Control)
Makes the sound clear when the volume is turned down when playing a DVD that
conforms to “Audio DRC.” This affects the output from the following jacks:
– OUT AUDIO L/R jacks
– DIGITAL AUDIO OUT (OPTICAL or COAXIAL) jack only when “Dolby
Digital” is set to “D-PCM.”
The default setting is indicated in bold print.
Standard
Normally select this position.
Wide Range
Gives you the feeling of being at alive performance.
Notes
• If you connect a component that does not conform to the selected audio signal, a loud noise
(or no sound) will come out from the speakers, affecting your ears or causing the speakers to
be damaged.
• Noise may occur in the LinearPCM double-speed audio. This is not a malfunction.
• If you set “DTS” to “On,” you cannot select surround setting (page 77).
DVD Settings and Adjustments
Audio Setup
57
Screen Setup
“Screen Setup” allows you to set the screen
according to the playback and connection
conditions.
SET UP
V/v/B/b
ENTER
1
SET UP
Press SET UP when the DVD player is in stop
mode, then press V/v to select
(DVD)
and press ENTER.
V v
ENTER
2
Press V/v to select “Screen Setup,” then press
ENTER.
ENTER
DVD SETUP
Language Setup
Audio Setup
Screen Setup
Parental Setup
ENTER
SCREEN SETUP
Press V/v to select the setup item from the displayed list:
“TV Type,” “DVD LINE1 RGB Out” or “DVD S-Video Out.”
ENTER
58
Screen Setup
SET UP
[ 4:3 Letter Box ]
TV Type
[ Off ]
DVD LINE1 RGB Out
[ On ]
DVD S-Video Out
V v B b ENTER
3
RETURN
RETURN
SET UP
4
Press B/b to select an item.
ENTER
5
SET UP
Press SET UP to exit the menu.
Menu choices
• TV Type
Selects the aspect ratio of the connected TV (4:3 standard or wide).
The default setting is indicated in bold print.
4:3 Letter Box
Select this when you connect a 4:3 screen TV. Displays a wide
picture with bands on the upper and lower portions of the screen.
4:3 Pan Scan
Select this when you connect a 4:3 screen TV. Automatically
displays the wide picture on the entire screen and cuts off the
portions that do not fit.
16:9
Select this when you connect a wide-screen TV or a TV with a wide
mode function.
4:3 Pan Scan
16:9
• DVD LINE1 RGB Out
Selects the method of outputting video signals from the LINE-1 (EURO AV) jack on
the rear panel of the player.
The default setting is indicated in bold print.
Off
Select this to not output RGB signals.
On
Select this to output RGB signals.
DVD Settings and Adjustments
4:3 Letter Box
• DVD S-Video Out
Selects whether or not to output S-video signals from the S-VIDEO OUT jack on the
rear panel of the player.
The default setting is indicated in bold print.
On
Select this when the player is connected to a TV with S-VIDEO
input jack.
Off
Select this when the player is connected to a TV lacking S-VIDEO
input jack.
continued
Screen Setup
59
Notes
• Playback settings stored in the disc take priority over the “DVD SETUP” menu settings and
not all the functions described may work.
• Depending on the DVD, “4:3 Letter Box” may be selected automatically instead of “4:3 Pan
Scan” or vice versa.
• The connection using S-VIDEO OUT jack is only for the DVD player.
• When you select “On” in the “DVD LINE1 RGB Out” setting, “DVD S-Video Out” is set to
“Off” automatically.
• When you select “On” in the “DVD LINE1 RGB Out” setting, S-video signal will not be
output properly.
• When you select “On” in the “DVD S-Video Out” setting, “DVD LINE1 RGB Out” is set to
“Off” automatically.
60
Screen Setup
Setting the display or sound track
language
You can set various languages for the disc’s
menu, sound track or subtitle.
SET UP
V/v/B/b
ENTER
SET UP
Press SET UP when the DVD player is in stop
mode, then press V/v to select
(DVD) and
press ENTER.
ENTER
2
ENTER
DVD SETUP
Language Setup
Audio Setup
Screen Setup
Parental Setup
V v
Press V/v to select “Language Setup,” then
press ENTER.
The “LANGUAGE SETUP” menu appears.
ENTER
RETURN
SET UP
DVD Settings and Adjustments
1
LANGUAGE SETUP
DVD Menu
Audio
Subtitle
V v
: English
: Original
: Audio Follow
ENTER
RETURN
SET UP
continued
Setting the display or sound track language
61
3
ENTER
4
Press V/v to select the language setup item from the displayed list:
“DVD Menu,” “Audio,” or “Subtitle.”
Then press ENTER.
Press V/v to select the desired language, then press ENTER.
ENTER
• DVD MENU LANGUAGE
You can select the desired language for the
disc’s menu.
DVD MENU LANGUAGE
B
DVD Menu
V v
• AUDIO LANGUAGE
Switches the language of the sound track.
When you select “Original,” the language
given priority in the disc is selected.
Audio
V v
• SUBTITLE LANGUAGE
Switches the language of the subtitle
recorded on the DVD. When you select
“Audio Follow,” the language for the
subtitle changes according to the language
you selected for the sound track.
5
SET UP
Subtitle
V v
ENTER
English
Français
Deutsch
Español
Italiano
Nederlands
Others
RETURN
SET UP
AUDIO LANGUAGE
English
Français
Deutsch
Español
Italiano
Nederlands
B Original
Others
ENTER
RETURN
SET UP
SUBTITLE LANGUAGE
B Audio Follow
English
Français
Deutsch
Español
Italiano
Nederlands
Others
ENTER
RETURN
SET UP
Press SET UP to exit the menu.
Tip
• If you select “Others” in step 4, an additional language
menu appears. Press V/v/B/b to select the desired
language, then press ENTER.
DVD MENU LANGUAGE
Cesky
Dansk
Magyar
Svenska
Norsk
Polski
Português
Suomi
Afrikaans
Arabic
Chinese
Greek
V v B b ENTER
Hindi
Japanese
Russian
Turkish
Thai
Korean
RETURN
SET UP
Notes
• When you select a language that is not recorded on the DVD in step 4, one of the recorded
languages will be automatically selected.
• Playback settings stored in the disc take priority over the DVD SETUP settings and not all the
functions described may work.
• If you change the DVD MENU LANGUAGE setting after playing the disc, press Z to open
and close the disc tray to activate the menu setting, then play the disc again.
62
Setting the display or sound track language
Parental Control (limiting playback by children)
Playback of some DVDs can be limited
according to a predetermined level such as
the age of the users. The parental control
function allows you to set a playback
limitation level.
Number
buttons
SET UP
V/v/B/b
ENTER
1
SET UP
Press SET UP when the DVD player is in stop
mode, then press V/v to select
(DVD)
and press ENTER.
ENTER
2
DVD SETUP
Language Setup
Audio Setup
Screen Setup
Parental Setup
V v
ENTER
Press V/v to select “Parental Setup,” then
press ENTER.
ENTER
RETURN
DVD Settings and Adjustments
H
SET UP
PARENTAL SETUP
Use Password
B b
[ No ]
RETURN
SET UP
continued
Parental Control (limiting playback by children)
63
3
Press b to select “Yes.”
• If you have not entered a password
ENTER
1
2
3
4
5
6
7
8
9
0
CREATE PASSWORD
The display for registering a new password
appears.
Enter a 4-digit password using the number
buttons.
Enter Password
– – – –
-~9
The display for confirming the password
appears.
Re-enter the password.
RETURN
CREATE PASSWORD
Re-enter Password
– – – –
-~9
• When you have already registered a
password
RETURN
PASSWORD CHECK
Enter Password
The display for entering the password appears.
Enter a 4-digit password using the number
buttons.
After registering a password, if you set “Use
password” to “No,” “PASSWORD CHECK”
screen will not appear.
– – – –
-~9
RETURN
PARENTAL SETUP
Use Password
Rating Level
Change Password
V v B b
4
Press V/v to select “Rating Level,” then press
ENTER.
ENTER
Press V/v to select the level you want, then
press ENTER.
ENTER
The options are as follows.
Level 8 (Adult) y Level 7 y Level 6 y
Level 5 y Level 4 y Level 3 y Level 2
y Level 1 (Kids Safe)
The lower the value, the stricter the limitation.
6
64
SET UP
Press SET UP to exit the menu.
Parental Control (limiting playback by children)
RETURN
SET UP
RATING LEVEL
Level 8 Adult
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1 Kids Safe
V v
5
[ Yes ]
:1
ENTER
RETURN
SET UP
RATING LEVEL
Level 8 Adult
Level 7
Level 6
Level 5
Level 4
Level 3
Level 2
Level 1 Kids Safe
V v
ENTER
RETURN
SET UP
To change the password
“Change Password” in step 4 on page 64.
1 Select
The display for entering a new password appears.
a new 4-digit password using the number buttons.
2 Enter
The display for confirming the password appears.
3 Re-enter the new password.
To turn off the Parental Control function
Set “Use Password” to “No” in step 3 on page 64.
To play a disc for which Parental Control is set
Insert the disc, then press H.
1 The
display for entering your password appears.
Enter your 4-digit password using the number buttons.
2 The player starts playback.
If you forget your password
Notes
• When you play DVDs which do not have the Parental Control function, playback cannot be
limited on this player.
• All the ratings higher than the level you select will be blocked.
• Write your password down and keep it in a safe place in case you forget it.
• All DVD settings below which you set in the “DVD SETUP” menu will also be cleared when
you reset the DVD-VCR to clear the password setting.
– Language Setup
– Audio Setup
– Screen Setup
– Parental Setup
Parental Control (limiting playback by children)
DVD Settings and Adjustments
1 Remove the disc and turn off the DVD-VCR.
2 Turn on the DVD-VCR again with no disc in the unit.
Hold down m and M on the front panel simultaneously for 5 seconds.
3 “Reset
OK” appears on the screen.
Turn off the DVD-VCR.
4 The password is cleared.
5 To create a new password, follow step 3 on page 64.
65
DVD Additional Operations
Using the DVD’s menu
A DVD is divided into long sections of a
picture or a music feature called “titles.”
When you play a DVD which contains
several titles, you can select the title you
want using the TOP MENU button.
Number
buttons
When you play DVDs that allow you to
select items such as the language for the
subtitles and the language for the sound,
select these items using the MENU button.
x
V/v/B/b
ENTER
MENU
TOP
MENU
1
Press TOP MENU or MENU.
The disc’s menu appears on the TV screen.
TOP MENU
The contents of the menu vary from disc to disc.
MENU
2
Press V/v/B/b to select the item you want to play or change.
You can also use the number buttons to select the item. In this case, step 3
is skipped.
ENTER
1
2
3
4
5
6
7
8
9
0
66
Using the DVD’s menu
3
Press ENTER.
ENTER
To turn off the DVD’s menu
Press x.
Note
• Depending on the DVD, you may not be able to use the TOP MENU button or search a point
by setting the time.
DVD Additional Operations
Using the DVD’s menu
67
Zooming into a scene
You can zoom into a scene during playback
or still mode.
To zoom into a JPEG image, see “Playing
JPEG image files” on page 84.
ZOOM
V/v/B/b
ENTER
1
MUTING/
ZOOM
2
Press ZOOM.
“
” appears.
Press V/v/B/b to move “
” to the position where you want to zoom in.
ENTER
3
Press ENTER repeatedly to change the magnification.
ENTER
Each time you press the button, the magnification changes as shown below.
2× t 4× t 2× t normal magnification
Notes
• You cannot use 4× magnification when you play VIDEO CDs.
• The zoom function may not work depending on the DVD.
68
Zooming into a scene
Changing the angles
If various angles (multi-angles) for a scene
are recorded on the DVD, “ ” appears in
the display when you press ANGLE during
playback. This means that you can change
the viewing angle.
Number
buttons
ANGLE
B/b
Press ANGLE during playback.
ANGLE
The angle number appears on the display.
The number after the slash indicates the total
number of angles.
2
Press B/b repeatedly or use the number buttons to select the angle number.
The scene changes to the selected angle.
ENTER
1
2
3
4
5
6
7
8
9
DVD Additional Operations
1
0
Note
• Check the user’s manual of the purchased disc to determine whether it supports angle
operation. However, note that angle operation may not be possible for some discs.
Changing the angles
69
Displaying the subtitle
If subtitles are recorded on the disc, you can
change the subtitles or turn them on and off
whenever you want while playing a DVD.
SUBTITLE
V/v/B/b
1
SUBTITLE/
TIMER
2
Press SUBTITLE during playback.
Press B/b repeatedly to select the language.
ENTER
3
Depending on the DVD, the choice of language varies.
Refer to “DVD Audio/Subtitle Language” on page 119 for the abbreviation
of the language.
Press V/v repeatedly to select “On.”
ENTER
To turn off the subtitles
Select “Off” in step 3.
Note
• Depending on the DVD, you may not be able to change the subtitles even if multilingual
subtitles are recorded on the DVD. You also may not be able to turn them off.
70
Displaying the subtitle
Various play mode functions (Programme
play, Shuffle play, Repeat play)
You can set the following play modes:
• Programme play (page 71), Programme play MP3 audio tracks (page 81)
• Shuffle play (page 73), Shuffle play MP3 audio tracks (page 82)
• Repeat play (page 74)
Note
• The play mode is cancelled when:
– you open the disc tray
– the player enters standby mode by pressing [/1.
Creating your own programme (Programme play)
You can play the contents of a disc in the
order you want by arranging the order of the
tracks on the disc to create your own
programme. You can programme up to 20
tracks.
CLEAR
REPEAT
H
V/v/B/b
ENTER
1
REPEAT/
INDEX
Press REPEAT when the DVD player is in stop
mode.
PROGRAM
DVD Additional Operations
To programme MP3 audio tracks, see
page 81.
SHUFFLE
continued
Various play mode functions (Programme play, Shuffle play, Repeat play)
71
2
Press B/b to select “PROGRAM,” then press
ENTER.
ENTER
PROGRAM
Track
01
05
09
13
17
02
06
10
14
18
03
07
11
15
19
Clear last
V v B b
3
Press V/v/B/b to select the track number you
want to programme, then press ENTER.
ENTER
ENTER
Track
02
06
10
14
18
03
07
11
15
19
Clear last
V v B b
To programme other tracks, repeat step 3.
5
Press H to start programme play.
track
–– –– –– ––
–– –– –– ––
–– –– –– ––
–– –– –– ––
–– –– –– ––
Clear all tracks
RETURN
CLEAR
PROGRAM
01
05
09
13
17
4
Program Order
04
08
12
16
20 B
Program Order
04
08
12
16
20 B
track
ENTER
06 –– –– ––
–– –– –– ––
–– –– –– ––
–– –– –– ––
–– –– –– ––
Clear all tracks
RETURN
CLEAR
The programmed track numbers are displayed in the selected order.
Programme play starts.
When the programme ends, you can restart the same programme again by
pressing H.
To stop programme play
Press CLEAR until “Off” appears at the upper left top of the TV screen during
programme play.
To change or cancel a programme
1 Follow steps 1 and 2 of “Creating your own programme (Programme play).”
v repeatedly to select “Clear last track,” then press ENTER. Each time you
2 Press
press the button, the last programmed number is canceled. You can also cancel
3
the last programmed number by pressing CLEAR.
Follow step 3 for new programming.
To cancel all the programmed numbers
1 Follow steps 1 and 2 of “Creating your own programme (Programme play).”
v repeatedly to select “Clear last track,” then press b to select “Clear all
2 Press
tracks” and press ENTER.
All the programmed numbers are canceled.
Notes
• Up to 99 tracks can be displayed.
• Up to 20 tracks can be programmed at one time.
72
Various play mode functions (Programme play, Shuffle play, Repeat play)
Playing in random order (Shuffle play)
You can shuffle the playback order of tracks.
Subsequent “shuffling” may produce a
different playing order.
CLEAR
REPEAT
To shuffle MP3 audio tracks, see page 82.
B/b
ENTER
1
REPEAT/
INDEX
Press B/b to select “SHUFFLE,” then press
ENTER.
PROGRAM
SHUFFLE
PROGRAM
SHUFFLE
ENTER
DVD Additional Operations
2
Press REPEAT when the DVD player is in stop
mode.
To return to normal play
Press CLEAR until “Off” appears at the upper left top of the TV screen during shuffle
play.
Tips
• Shuffle play will stop when all the tracks are played back.
• You cannot repeat play while in shuffle play.
continued
Various play mode functions (Programme play, Shuffle play, Repeat play)
73
Playing repeatedly (Repeat play)
You can play all of the titles or tracks on a
disc or a single title, chapter, or track
repeatedly.
CLEAR
REPEAT
B/b
1
REPEAT/
INDEX
2
REPEAT/
INDEX
Press REPEAT during playback.
Off
Press REPEAT or B/b to select the item to be repeated.
When playing a DVD
• Chapter: repeats the current chapter.
• Title: repeats the current title on a disc.
When playing a VIDEO CD (with PBC function off) or CD
• Track: repeats the current track.
• Disc: repeats all of the tracks.
When playing a DATA CD (MP3 audio)
• FILE: repeats the current file (track).
• DIR: repeats the current directory (album).
• DISC: repeats the current disc.
To return to normal play
Select “Off” in step 2 or press CLEAR during repeat play.
74
Various play mode functions (Programme play, Shuffle play, Repeat play)
Tip
• When playing a DATA CD, press REPEAT again to cancel repeat play.
Notes
• You cannot repeat play with DVD-RW in VR mode.
• You cannot repeat play VIDEO CDs with PBC function on. See “Playing VIDEO CDs with
“PBC On/Off” functions” on page 88.
DVD Additional Operations
Various play mode functions (Programme play, Shuffle play, Repeat play)
75
Changing the sound
When playing a DVD recorded in multiple
audio formats (PCM, Dolby Digital, MPEG
or DTS), you can change the audio format. If
the DVD is recorded with multilingual
tracks, you can also change the language.
AUDIO
With CDs, DATA CDs, or VIDEO CDs, you
can select the sound from the right or left
channel and listen to the sound of the
selected channel through both the right and
left speakers. For example, when playing a
Karaoke VIDEO CD containing a song with
the vocals on the right channel and the
instruments on the left channel, you can hear
the instruments from both speakers by
selecting the left channel.
B/b
To enjoy Dolby Digital or DTS effect from a
LinearPCM format disc, you have to make
the B-2 connection as shown on page 53.
1
AUDIO
2
ENG DOLBY DIGITAL 3/2.1CH 1/2 B b
Press B/b repeatedly to select the desired language/audio setting.
ENTER
76
Press AUDIO during playback.
Changing the sound
• When playing a DVD
Depending on the DVD, the choice of language varies.
Refer to “DVD Audio/Subtitle Language” on page 119 for the
abbreviation of the language.
• When playing a VIDEO CD or CD
The default setting is indicated in bold print.
STEREO
The standard stereo sound
Left
The sound of the left channel (monaural)
Right
The sound of the right channel (monaural)
Virtual surround setting
When you connect a stereo TV or 2 front
speakers, SURROUND lets you enjoy
surround sound effects by using sound
imaging to create virtual rear speakers from
the sound of the front speakers without using
actual rear speakers.
SURROUND
B/b
SURROUND
2
Press SURROUND during playback.
Off
Press B/b repeatedly to select “Surround1,” “Surround2,” “Surround3.”
ENTER
Surround effect increases as shown below.
Surround1
Surround2
Surround3
TV
TV
TV
DVD Additional Operations
1
: Virtual speaker
continued
Virtual surround setting
77
To cancel the setting
Select “Off” in step 2.
Notes
• When the playing signal does not contain a signal for the rear speakers, the surround effects
will be difficult to hear.
• When you activate the surround effect, turn off the surround setting of the connected TV or
amplifier (receiver).
• Make sure that your listening position is between and at an equal distance from your
speakers, and that the speakers are located in similar surroundings.
• If you use the DIGITAL AUDIO OUT (OPTICAL or COAXIAL) jack and set “Dolby
Digital” to “Dolby Digital” or “DTS” to “On” in “AUDIO SETUP” menu, sound will come
from your speakers but it will not have the surround effect.
78
Virtual surround setting
Playing an MP3 audio track
You can play back DATA CDs (CD-ROMs/
CD-Rs/CD-RWs) recorded in MP3 (MPEG1
Audio Layer 3) format.
Z
CLEAR
REPEAT
H
x
V/v/B/b
ENTER
TOP MENU
1
Press Z and place a DATA CD on the disc tray,
then press Z to close the tray.
When you load a DATA CD which contains
MP3 audio tracks and JPEG image files,
“Select a Media Type” menu appears.
Select a Media Type
1 MP3
2 JPEG
V v
ENTER
If you load a DATA CD which contains only
MP3 audio files, the MP3 display appears.
Then you can skip step 2.
DVD Additional Operations
O RETURN
continued
Playing an MP3 audio track
79
2
Press V/v to select “MP3,” then press
ENTER.
ENTER
The first track starts playing. Press x if
necessary.
Repeat mode
Elapsed playing time
MP3
track 1
DIRECTORY:007
album 1
album 2
album 3
album 4
album 5
album 6
album 7
V v B b ENTER
3
RETURN
Press O RETURN, then press V/v to select
the desired directory in the left column, then
press ENTER.
track 1
DIRECTORY:007
album 1
album 2
album 3
album 4
album 5
album 6
album 7
V v B b ENTER
Press V/v to select the desired track in the
right column, then press ENTER.
ENTER
The selected track starts playing.
When a track or album is being played, the title
is shown in a box. The playing track number
appears on the display window.
track 5
DIRECTORY:007
album 1
album 2
album 3
album 4
album 5
album 6
album 7
V v B b ENTER
To repeat play
Press REPEAT repeatedly during playback to change the repeat mode.
To go to the next or previous page
Press b or B.
To return to the previous display
Press O RETURN.
To return to the “Select a Media Type” menu
Press x twice, then press TOP MENU.
To turn off the display
Press x twice, then press O RETURN repeatedly.
80
Playing an MP3 audio track
RETURN
SET UP
00:00
FILES:014
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
OFF
1
2
3
4
5
6
7
8
9
10
RETURN
SET UP
MP3
To stop play
Press x.
• FILE: repeats the current file (track).
• DIR: repeats the current directory (album).
• DISC: repeats the current disc.
OFF
1
2
3
4
5
6
7
8
9
10
MP3
ENTER
4
00:00
FILES:014
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
00:01
FILES:014
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
mp3 track
1
2
3
4
5
6
7
8
9
10
RETURN
OFF
Notes
• Only the letters in the alphabet and numbers can be used for album or track names. Anything
else is displayed as an asterisk.
• Up to 12 alphanumeric characters can be displayed for album or track names.
• ID3 tags cannot be displayed.
To programme MP3 audio tracks
1 Press x twice, then press REPEAT.
B/b to select “PROGRAM,” then press
2 Press
ENTER.
PROGRAM
SHUFFLE
PROGRAM
00:00
DIRECTORY:007
V v
V/v to select the desired directory in the left
3 Press
column, then press ENTER.
ENTER
RETURN
CLEAR
PROGRAM
00:00
DIRECTORY:003
mp3 track 1
mp3 track 2
mp3 track 3
mp3 track 4
mp3 track 5
OFF
ORDER:000
ENTER
RETURN
CLEAR
PROGRAM
00:00
DIRECTORY:003
mp3 track 1
mp3 track 2
mp3 track 3
mp3 track 4
mp3 track 5
V v
OFF
ORDER:001
mp3 track 3
ENTER
RETURN
CLEAR
programme other tracks, repeat step 4.
5 To
The programmed tracks are displayed in the selected
DVD Additional Operations
V v
Press V/v to select the track you want to programme,
4 then
press ENTER.
OFF
ORDER:000
album 1
album 2
album 3
album 4
album 5
album 6
album 7
order. Press CLEAR to cancel the last programmed
track.
Press H to start programme play.
6 Programme play starts. When the programme ends,
you can restart the same programme again by
pressing H.
To stop programme play
Press x during programme play.
Note
• Up to 20 tracks can be programmed at one time.
continued
Playing an MP3 audio track
81
To return to normal play
Press CLEAR during programme play.
Tip
• You cannot repeat play while in programme play.
To shuffle MP3 audio tracks
1 Press REPEAT when the MP3 is in stop mode.
2 Press B/b to select “SHUFFLE,” then press ENTER.
PROGRAM
SHUFFLE
To return to normal play
Press CLEAR during shuffle play.
Tips
• Shuffle play will stop when all the tracks are played back.
• You cannot repeat play while in shuffle play.
About MP3 audio tracks
You can play MP3 audio tracks on CD-ROMs, CD-Rs, or CD-RWs. However, the
discs must be recorded according to ISO9660 level 1 or level 2 format for the player
to recognize the tracks.
You can also play discs recorded in Multi Session.
See the instructions of the CD-R/RW device or recording software (not supplied) for
details on the recording format.
To play a Multi Session CD
This player can play Multi Session CDs when an MP3 audio track is located in the
first session. Any subsequent MP3 audio tracks, recorded in the later sessions, can
also be played back. When audio tracks and images in music CD format or video CD
format are recorded in the first session, only the first session will be played back.
Notes
• If you put the extension “.MP3” to data not in MP3 format, the player cannot recognize the
data properly and will generate a loud noise which could damage your speaker system.
• The player cannot play audio tracks in MP3PRO format.
• This player supports MP3 audio tracks recorded with a bit rate of 128 kbps and a sampling
frequency of 44.1 kHz. Attempting to play MP3 audio tracks recorded with different
specifications may result in loud noise, sound skipping or speaker damage.
• Depending on the disc, playback may take some time to start.
82
Playing an MP3 audio track
The Playback order of MP3 audio tracks
The playback order of albums and tracks recorded on a DATA CD is as follows.
• Structure of disc contents
Tree 1
Tree 2
Tree 3
Tree 4
Tree 5
album
track
When you press O RETURN and the list of MP3 albums appears (page 80), the
albums are arranged in the following order: A t B t C t D t F t G.
Albums that do not contain tracks (such as album C) do not appear in the list.
Tips
• If you add numbers (01, 02, 03, etc.) to the front of the track file names, the tracks will be
played in that order.
• A disc with many trees takes longer to start playback. Some discs with many trees cannot be
played back.
DVD Additional Operations
When you insert a DATA CD and press H, the numbered tracks are played
sequentially, from 1 through 7. Any sub-albums/tracks contained within a currently
selected album does not take priority over the next album in the same tree. (Example:
E contains G but 6 is played before 7.)
Notes
• Depending on the software you use to create the DATA CD, the playback order may differ
from the illustration above.
• The playback order above may not be applicable if there are more than a total of 1000 albums
and tracks in the DATA CD.
• A total of up to 999 files can be recognized for discs that contain both MP3 and JPEG files.
Files are recognized in the order that they were recorded. For example, if 990 JPEG files are
recorded then 100 MP3 files are recorded, the 990 JPEG files recorded first and only the first
9 MP3 files can be recognized.
• Depending on the disc contents, playback may take some time to start.
Playing an MP3 audio track
83
Playing JPEG image files
You can play JPEG image files on DATA
CDs (CD-ROMs/CD-Rs/CD-RWs).
Z
CLEAR
./>
H
x
V/v/B/b
ENTER
MENU
TOP MENU
1
Press Z and place a DATA CD on the disc tray,
then press Z to close the tray.
When you load a DATA CD which contains
MP3 audio tracks and JPEG image files,
“Select a Media Type” menu appears.
Select a Media Type
1 MP3
2 JPEG
V v
ENTER
If you load a DATA CD which contains only
JPEG image files, the “Album” display
appears. Then you can skip step 2.
2
Press V/v to select “JPEG,” then press
ENTER.
Album
Photo:
ENTER
The “Album” display will appears.
If you do not press ENTER after selecting a
media type, the selected media will be
automatically played.
84
Playing JPEG image files
SLIDE SHOW
3
Press ./> to select the next/previous album page, then press V/v/
B/b to select an image in the “Album” display.
To display the selected image
1 Press ENTER.
ENTER
The selected image number appears in the
display window.
2 To display the next/previous image, press
./>.
IMAGE
To play the Slide show
: Fast
: Normal
: Slow
1 Press H.
You can also play the Slide show using the
menu on the selected image.
For details, see “To enjoy the Slide show”
on page 86.
2 Press B/b to select the desired playing
speed on the “Interval” menu, then press
ENTER.
Slide show starts from the selected image.
Interval
IMAGE
To rotate the selected image
IMAGE
clockwise by 90°.
To zoom in an image
Press V/v/B/b to select an image in the “Album”
1 display,
then press ENTER.
Press B/b to select “ ,” then press ENTER.
2 “ ” appears.
Press V/v/B/b to move “ ” to the position where
3 you
want to zoom in.
Press ENTER repeatedly to change the
4 magnification. Each time you press ENTER, the
IMAGE
DVD Additional Operations
Press V/v/B/b to select an image in the “Album”
1 display,
then press ENTER.
B/b to select “
,” then press ENTER.
2 Press
Each time you press ENTER, the image turns
magnification changes as shown below.
2× t normal magnification
continued
Playing JPEG image files
85
To enjoy the Slide show
V/v/B/b to select an image in the “Album”
1 Press
display, then press ENTER.
Press B/b to select “
,” then press ENTER.
2 The
“Interval” menu appears.
Press B/b to select the desired playing speed, then
3 press
ENTER.
Interval
Slide show starts.
To turn on/off the menu in the single image display
Press CLEAR to turn off the menu. Press B or b to turn on the menu.
To return to the “Album” display
Press MENU to return to the “Album” display. Press . repeatedly to return to the
first “Album” page.
To return to the “Select a Media Type” menu
Press x twice, then press TOP MENU.
Notes
• Slide show can play in only one direction.
• You cannot rotate or zoom in the image during Slide show.
• If you select “
” in the rotated image display, the images in the “Album” display will not
be rotated. But if you start the slide show, the images will be rotated. Correct the rotation in
the “
” menu.
About JPEG image files
You can play JPEG image files on CD-ROMs, CD-Rs, or CD-RWs. However, the
discs must be recorded according to ISO9660 level 1 or level 2 format for the player
to recognize the files.
You can also play discs recorded in Multi Session.
See the instructions of the CD-R/RW device or recording software (not supplied) for
details on the recording format.
Note
• A total of up to 999 files can be recognized for discs that contain both MP3 and JPEG files.
Files are recognized in the order that they were recorded. For example, if 990 JPEG files are
recorded then 100 MP3 files are recorded, the 990 JPEG files recorded first and only the first
9 MP3 files can be recognized.
To play a Multi Session CD
This player can play Multi Session CDs when an JPEG image file is located in the
first session. Any subsequent JPEG image files, recorded in the later sessions, can
also be played back. When audio tracks and images in music CD format or video CD
format are recorded in the first session, only the first session will be played back.
86
Playing JPEG image files
Tip
• If you add numbers (01, 02, 03, etc.) to the front of the file names, the files will be played in
that order.
Notes
• The system can play the extension “.JPG” or “.JPEG.”
• Some CD-Rs or CD-RWs cannot be played on this system depending on file format.
• If you add the extension “.JPG” or “.JPEG” to data not in JPEG format, “Can not Display”
will appear.
• Depending on the disc or the size of image files, playback may take some time to start.
• Progressive and lossless compression JPEG image files are not supported.
• The image size that can be displayed is limited. You can display the following images;
width 32 – 7680 pixels by height 32 – 8192 pixels.
DVD Additional Operations
Playing JPEG image files
87
Playing VIDEO CDs with “PBC On/Off”
functions
The PBC (Playback control) function allows
you to search and perform other operations
interactively. PBC playback follows a
selection menu displayed on your TV screen.
Number
buttons
H
V/v
ENTER
O RETURN
MENU
1
Press MENU to select “PBC On.”
The menu for your selection appears.
MENU
2
Press V/v to select the item number you want.
You can also use the number buttons to select the item number and track.
ENTER
1
2
3
4
5
6
7
8
9
0
88
Playing VIDEO CDs with “PBC On/Off” functions
3
Press ENTER.
ENTER
4
Follow the instructions in the menu for interactive operations.
Refer to the instructions supplied with the disc, as the operating procedure
may differ depending on the VIDEO CD.
To return to the menu
Press O RETURN.
To play using “PBC Off”
Press MENU to select “PBC Off.”
When “PBC Off” is selected, the DVD player starts continuous play. You cannot
play still pictures such as a menu.
To return to “PBC On,” press MENU to select “PBC On.”
Tip
• Depending on the VIDEO CD, “Press ENTER” in step 3 may appear as “Press SELECT” in
the instructions supplied with the disc. In this case, press H.
DVD Additional Operations
Playing VIDEO CDs with “PBC On/Off” functions
89
VCR Additional Operations
Quick Timer Recording
After you have started recording, you can
have the VCR stop recording automatically
after a specified duration.
z REC
x
1
REC
While recording, press z REC.
2
REC
Press z REC repeatedly to set the duration time.
In SP mode
Each press advances the time in increments of 30 minutes.
0:30
1:00
4:00
4:30
Normal recording
In LP mode
Each press advances the time as shown below.
0:30
1:00
8:00
9:00
Normal recording
The tape counter decreases minute by minute to 0:00, then the VCR stops
recording.
90
Quick Timer Recording
To extend the duration
Press z REC repeatedly to set a new duration time.
To cancel the duration
Press z REC repeatedly until the
normal recording mode.
indicator disappears and the VCR returns to
To stop while recording
Press x.
Notes
• You cannot display the current tape time in the display window when setting the recording
duration time.
• During DVD playback, DVD-VCR does not standby even if the VCR stops recording.
VCR Additional Operations
Quick Timer Recording
91
Recording stereo and bilingual
programmes
In the NICAM system
This VCR receives and records stereo and bilingual programmes based on the
NICAM system (NICAM appears on the TV screen). When a stereo or bilingual
programme is received, the STEREO indicator appears in the display window.
To record a NICAM programme, “NICAM” in the “USER SET” menu should be set
to “On” (initial setting). To check the menu setting, see page 103 for details.
To select the sound while recording
Press AUDIO to select the sound you want.
Stereo programmes
To listen to
On-screen display
Display window
Stereo
NICAM, STEREO
STEREO
Left channel
NICAM, LCH
STEREO
Right channel
NICAM, RCH
STEREO
Left and right channels*
NICAM, LCH + RCH
STEREO
* Usually the mixed sound of left and right channels
Bilingual programmes
To listen to
On-screen display
Display window
Main
NICAM, MAIN
STEREO
Sub
NICAM, SUB
STEREO
Main and sub
NICAM, MAIN/SUB
STEREO
Standard sound*
NICAM, MONO
STEREO
* Usually the main sound (monaural)
92
Recording stereo and bilingual programmes
Selecting the sound during Hi-Fi playback
Press AUDIO to select the sound you want.
To listen to
On-screen display
Display window
Stereo
STEREO
STEREO
Left channel
LCH
STEREO
Right channel
RCH
STEREO
Mix sound*
MIX
STEREO
Mono sound
MONO
No indicator
* The mixed sound of left and right channels, and the normal mono audio track
How sound is recorded on a video tape
The VCR records sound onto two separate tracks. Hi-fi audio is recorded onto the
main track along with the picture. Monaural sound is recorded onto the normal audio
track along the edge of the tape.
Normal audio track
(monaural)
Stereo
Usually mixed
left/right channels
Bilingual
Usually main sound
Hi-fi audio track
(main track)
Stereo sound
(left/right channels)
Main (left channel)
Sub (right channel)
Recording stereo and bilingual programmes
VCR Additional Operations
Notes
• To listen to playback sounds in stereo, you must use the Scart or AUDIO OUT connections.
• When you play a tape recorded in monaural, the sound is heard in monaural regardless of the
AUDIO setting.
93
Searching using index function
The VCR automatically marks the tape with
an index signal at the point where each
recording begins. Use these signals as
references to find a specific recording.
INDEX
m/M
H
x
To find a specific recording by scanning (Index scan)
1
2
Insert an indexed tape into the tape compartment.
REPEAT/
INDEX
Press INDEX, then press m/M. The
VCR starts scanning each recording for five
seconds in the corresponding direction.
INDEX SCAN : B B
3
94
Press H to start playback when you find the desired point.
Searching using index function
To search a specific recording (Index search)
1
2
Insert an indexed tape into the VCR.
REPEAT/
INDEX
Press INDEX, then press m/M twice.
• To search ahead, press M twice.
• To search backwards, press m twice.
3
INDEX SEARCH : B B +01
Press m/M depending on the direction where your desired programme
is located.
Each time you press the button, the number increases or decreases up to
±20, respectively.
4
The VCR starts searching, and playback starts automatically from that
point.
To stop searching
Press x.
Searching using index function
VCR Additional Operations
Note
• No index signal will be added when recording starts from recording pause. However, an
index signal will be marked if you change the programme position during recording pause.
95
Adjusting the picture (tracking)
Adjusting the tracking
Although the VCR automatically adjusts the
tracking when playing a tape, distortion may
occur if the recording is in poor condition. In
this case, manually adjust the tracking.
TRACKING – – – – – –
During playback, press TRACKING +/– to
display the tracking meter. The distortion
should disappear as you press one of the two
buttons. To resume automatic tracking
adjustments, eject the tape and re-insert it.
– – – – – –
Tracking meter
Adjusting the picture
sharpness (Smart trilogic)
SET UP
You can automatically adjust the sharpness of
the picture.
V/v/B/b
ENTER
O RETURN
1
SET UP
During playback, press SET UP, then press
V/v to select
(OPTION) and press
ENTER.
ENTER
96
Adjusting the picture (tracking)
OPTION
Language :English
Clock
Install
User Set
[ Off ]
Auto Power Off
[ On ]
Screen Messages
Power Save
[ Off ]
V v
ENTER
RETURN
SET UP
2
Press V/v to select “User Set,” then press
ENTER.
USER SET
ENTER
V v B b
3
Press V/v to select “Smart Trilogic,” then
press b.
RETURN
SET UP
USER SET
[ Auto ]
[ On ]
[ On ]
[ Off ]
Colour System
NICAM
Smart Trilogic
VideoPlus Extend
ENTER
V v B b
4
[ Auto ]
[ On ]
[ On ]
[ Off ]
Colour System
NICAM
Smart Trilogic
VideoPlus Extend
RETURN
Press V/v to set “SMART TRILOGIC” to
“ON” or “OFF.”
SET UP
PICTURE
ENTER
• ON: Picture sharpness is automatically
adjusted.
• OFF: Adjust the picture sharpness
manually.
SMART TRILOGIC : ON
SHARPEN
SOFTEN
–––––––––––*––––––––
RETURN
bB
ON / OFF : v V
To soften the picture, press B.
To sharpen the picture, press b.
5
Press O RETURN to return to the original screen.
VCR Additional Operations
RETURN
Adjusting the picture (tracking)
97
Changing menu options
SET UP
V/v/B/b
ENTER
1
SET UP
Press SET UP when the DVD player is in stop
mode, then press V/v to select
(OPTION) or
(VIDEO) and press
ENTER.
OPTION
Language :English
Clock
Install
User Set
[ Off ]
Auto Power Off
[ On ]
Screen Messages
Power Save
[ Off ]
V v
ENTER
ENTER
RETURN
SET UP
VIDEO SETUP
Tape Select
Repeat Play
V v B b
2
Changing menu options
SET UP
VIDEO SETUP
Tape Select
Repeat Play
V v B b
98
RETURN
Press V/v to select the option to change.
ENTER
[ E180 ]
[ Off ]
[ E180 ]
[ Off ]
RETURN
SET UP
3
Press B/b to change the setting.
ENTER
4
SET UP
Press SET UP to exit the menu.
Menu choices
The default settings are indicated in bold print.
OPTION
Menu option
Set this option to
Auto Power Off
• “Off” to deactivate the Auto Power Off function.
• “1Hour”/“2Hours”/“3Hours” to turn the DVD-VCR off
automatically if no signal is received and you do not press any
of the buttons during this time.
Screen Messages
• “On” to display the menu on the TV screen.
• “Off” to disappear the menu from the TV screen.
Power Save
• “On” to turn off the indicators in the display window during
standby mode to reduce the DVD-VCR’s power consumption
to a minimum.
• “Off” to turn on the indicators in the display window while the
DVD-VCR is standing by.
Menu option
Set this option to
Tape Select
•
•
•
•
Repeat Play
• “On” to play back a tape repeatedly. The VCR rewinds a tape
to the beginning and restarts playback automatically.
• “Off” to turn off Auto repeat.
“E180” to use an E-180 or shorter type tape.
“E240” to use an E-240 type tape.
“E260” to use an E-260 type tape.
“E300” to use an E-300 type tape.
VCR Additional Operations
VIDEO SETUP
Notes
• When the VCR stands by for recording, the
indicator in the display window remains lit
even when “Power Save” is set to “On.”
• The Line Through function will not operate properly if “Power Save” in “OPTION” menu is
set to “On.” Set “Power Save” to “Off” to ensure proper operation.
Changing menu options
99
Editing
How to connect to record on this VCR
Connect the line outputs of the other VCR to the input connector of this VCR. Refer to the
examples A through C and choose the connection that best suits your VCR.
Example A
TV
Your VCR (Recorder)
LINE-1 (EURO AV)
Other VCR (Player)
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
Example B
TV
Your VCR (Recorder)
LINE-2 IN t/o L/R
Other VCR (Player)
LINE OUT
audio/video cord
(not supplied)
100
Editing
: Signal flow
Example C
Your VCR (Recorder)
TV
Other VCR (Player)
LINE-3
Scart
(EURO-AV)
Scart cable (not supplied)
: Signal flow
How to connect to a stereo system
Connect the LINE-2 IN t/o L/R jacks on this DVD-VCR to the audio output jacks on the
stereo system, using an audio cable (not supplied).
VCR Additional Operations
Notes
• Make sure you connect the plugs to jacks of the same colour.
• If the other VCR is a monaural type, leave the red plugs unconnected.
• If you connect this VCR to both the LINE IN and LINE OUT jacks of the other VCR, select
the input correctly to prevent a humming noise.
• When you connect another VCR to the LINE-3 or LINE-2 connector, press INPUT SELECT
to display “L3” or “L2” in the display window.
continued
Editing
101
Operation (when recording on this VCR)
Before you start editing
• Turn on your TV and set it to the video
channel.
x
• Press INPUT SELECT to display the
connected line in the display window.
• Press SELECT VIDEO to control the
VCR.
X
z REC
• Press SP/LP to select the tape speed, SP or
LP.
1
Insert a source tape with its safety tab removed into the other (playback)
VCR. Search for the point to start playback and set it to playback pause.
2
Insert a tape with its safety tab in place into this (recording) VCR. Search
for the point to start recording and press X to set it to playback pause.
3
4
REC
Press z REC on this VCR to set it to recording pause.
To start editing, press the X (pause) buttons on both VCRs at the same time.
To stop editing
Press the x (stop) buttons on both VCRs.
Tip
• To cut out unwanted scenes while editing, press X on this VCR when an unwanted scene
begins. When it ends, press X again to resume recording.
102
Editing
Additional Information
General setup information
Changing setup options
SET UP
V/v/B/b
ENTER
1
SET UP
Press SET UP when the DVD player is in stop
mode, then press V/v to select
(OPTION) and press ENTER.
2
V v
Press V/v to select “User Set,” then press
ENTER.
ENTER
The “USER SET” menu appears.
ENTER
SET UP
USER SET
Colour System
NICAM
Smart Trilogic
VideoPlus Extend
V v B b
3
RETURN
RETURN
[ Auto ]
[ On ]
[ On ]
[ Off ]
SET UP
Additional Information
ENTER
OPTION
Language :English
Clock
Install
User Set
[ Off ]
Auto Power Off
[ On ]
Screen Messages
Power Save
[ Off ]
Press V/v to select the option to change.
ENTER
continued
General setup information
103
4
Press B/b to change the setting.
ENTER
5
SET UP
When changing the “RF Output Channel,” confirmation messages will
appear. Press ENTER to confirm the messages.
Press SET UP to exit the menu.
Menu choices
Initial settings are indicated in bold print.
104
Menu option
Set this option to
Colour System
• “Auto” to select the colour system automatically.
• “PAL” to use the tape recorded in the PAL colour system.
• “B/W” to use the tape recorded in black and white.
When using the tape recorded NTSC colour signals:
• “NTPB” to play back an NTSC-recorded tape on PAL TV.
• “NT4.43” to play back an NTSC-recorded tape on Multi TV.
NICAM
• “On” to record NICAM broadcasts on the hi-fi audio track.
• “Off” to record standard sound on the hi-fi audio track.
For details, see page 92.
Smart Trilogic
• “On” to automatically adjust the sharpness of the picture.
• “Off” to manually adjust the sharpness of the picture.
VideoPlus Extend
• “Off” to deactivate the VideoPlus Extend function.
• 10/20/30/.../60 (minutes) to extend the time of the VideoPlus
setting by the selected amount of time.
General setup information
Troubleshooting
If you have any questions or problems not covered below, please consult your nearest Sony
service facility.
Others
Clock
Power
General Troubleshooting
Symptom
Remedy
The ?/1 (on/standby) switch does
not function.
• Connect the mains lead to the mains securely.
The power is turned on but the DVDVCR does not operate.
• Moisture condensation has occurred. Turn the power off,
unplug the mains lead and leave the DVD-VCR to dry for
over three hours.
The clock has stopped and “--:--”
appears in the display window.
• The clock stops if the DVD-VCR is disconnected from
the mains. Reset the clock (and timer).
The remote commander does not
function.
• Make sure you are pointing the remote commander at the
remote sensor on the DVD-VCR.
• Replace all the batteries in the remote commander with
new ones if they are weak.
• Make sure the TV / DVD·VIDEO switch is set correctly.
• Select correctly VIDEO or DVD with the SELECT DVD/
VIDEO button.
The tracking meter does not appear
on the screen.
• The recording condition of the tape is very poor and
tracking cannot be adjusted.
You cannot control other TVs.
• Set your TV’s code number. The code number may
change when you replace the batteries of the remote
commander.
Additional Information
continued
Troubleshooting
105
DVD Troubleshooting
Remedy
There is no picture/picture noise
appears.
• Re-connect the connecting cord securely.
• The connecting cords are damaged.
• Check the connection to your TV (page 11) and switch
the input selector on your TV so that the signal from the
player appears on the TV screen.
• The disc is dirty or flawed.
• If the picture output from your player goes through your
VCR to get to your TV or if you are connected to a
combination TV/VIDEO player, the copy-protection
signal applied to some DVD programmes could affect
picture quality. If you still experience problems even
when you connect your player directly to your TV, please
try connecting your player to your TV’s S-VIDEO input
(page 54).
Even though you set the aspect ratio
in “TV Type” of the “SCREEN
SETUP” menu the picture does not
fill the screen.
• The aspect ratio of the disc is fixed on your DVD.
There is no picture from your VCR
connected to the LINE IN jacks.
• The DVD player must be in standby mode to view
pictures from your VCR.
There is no sound.
• Re-connect the connecting cord securely.
• The connecting cord is damaged.
• The player is connected to the wrong input jack on the
amplifier (receiver) (page 52).
• The amplifier (receiver) input is not correctly set.
• The player is in pause mode or in Slow-motion Play
mode.
• The player is in fast forward or fast reverse mode.
• If the audio signal does not come through the DIGITAL
AUDIO OUT (OPTICAL or COAXIAL) jack, check the
audio settings (page 55).
Sound is noisy.
• When playing a CD with DTS sound tracks, noise will
come from the OUT AUDIO L/R jacks (page 30) or
DIGITAL OUT (OPTICAL or COAXIAL) jack.
The sound volume is low.
• The sound volume is low on some DVDs. The sound
volume may improve if you set “Audio DRC” to “Wide
Range” (page 57).
Sound
Picture
Symptom
106
Troubleshooting
The MP3 audio track cannot be
played (page 79).
• The DATA CD is not recorded in the MP3 format that
conforms to ISO9660 Level 1/Level 2.
• The MP3 audio track does not have the extension “.MP3.”
• The data is not formatted in MP3 even though it has the
extension “.MP3.”
• The data is not MPEG1 Audio Layer 3 data.
• The player cannot play audio tracks in MP3PRO format.
The JPEG image file cannot be
played.
• The DATA CD is not recorded in JPEG format that
conforms to ISO9660 Level 1/Level 2.
• The JPEG image file does not have the extension “.JPG”
or “.JPEG.”
• The data is not formatted in JPEG even though it has the
extension “.JPG” or “.JPEG.”
• Length or width of the image is more than 4720 dots.
The title of the MP3 audio album/
track or JPEG image album/file is not
correctly displayed.
• The player can only display numbers and alphabet. Other
characters are displayed as asterisks.
The disc does not start playing from
the beginning.
• Programme play, shuffle play, or repeat play, has been
selected (pages 71, 73, 74).
• Resume play has taken effect (page 29).
The player starts playing the disc
automatically.
• The disc features an auto playback function.
Playback stops automatically.
• While playing discs with an auto pause signal, the player
stops playback at the auto pause signal.
You cannot perform some functions
such as stop, search, slow-motion
play, repeat play, shuffle play, or
programme play.
• Depending on the disc, you may not be able to do some
operations. See the operating manual that comes with the
disc.
The language for the sound track
cannot be changed.
• Try using the DVD’s menu instead of the direct selection
button on the remote (page 66).
• Multilingual tracks are not recorded on the DVD being
played.
• The DVD prohibits the changing of the language for the
sound track.
Operation
Remedy
• The disc is turned over.
• Insert the disc with the playback side facing down on the
disc tray.
• The disc is skewed.
• The player cannot play certain discs (page 7).
• The region code on the DVD does not match the player.
• Moisture has condensed inside the player.
• The player cannot play CD-Rs, CD-RWs, DVD-Rs or
DVD-RWs that are not finalized (page 7).
• Make sure the TV / DVD·VIDEO switch is set correctly.
• Select correctly VIDEO or DVD with SELECT DVD/
VIDEO button.
Additional Information
Symptom
The disc does not play.
continued
Troubleshooting
107
Operation
Symptom
Remedy
The subtitle language cannot be
changed or turned off.
• Try using the DVD’s menu instead of the direct selection
button on the remote (page 66).
• Multilingual subtitles are not recorded on the DVD being
played.
• The DVD prohibits the changing of the subtitles.
The angles cannot be changed.
• Try using the DVD’s menu instead of the direct selection
button on the remote (page 66).
• Multi-angles are not recorded on the DVD being played.
• The DVD prohibits changing of the angles.
The player does not operate properly.
• When static electricity, etc., causes the player to operate
abnormally, unplug the player.
VCR Troubleshooting
Remedy
The playback picture does not appear
on the TV screen.
• Make sure the TV is set to the channel for the VCR. If
you are using a monitor, set it to video input.
• If the VCR is connected to the TV with the Scart cable,
make sure the VIDEO indicator is lit in the display
window. Use the TV/VIDEO button on the remote
commander to light up the VIDEO indicator.
The picture is not clear.
• Existing broadcasts may interfere with the VCR. Reset
the RF channel output of your VCR (page 15).
• Adjust the tracking with the TRACKING +/– buttons.
• The video heads are dirty (see the last page of
Troubleshooting). Clean the video heads using a Sony
video head cleaning cassette. If a Sony cleaning cassette
is not available in your area, have the heads cleaned at
your nearest Sony service facility (a standard service
charge will be required). Do not use a commercially
available liquid type cleaning cassette other than Sony’s,
as it may damage the video heads.
• The video heads may have to be replaced. Consult your
local Sony service facility for more information.
The picture has no colour.
• The “Colour System” option in the “USER SET” menu is
set to the wrong position. Set the option to conform to the
system that the tape was recorded in.
The picture rolls vertically during
picture search.
• Adjust the vertical hold control on the TV or monitor.
The picture has no sound.
• The tape is defective.
• If you made A/V connections, check the audio cord
connection.
The sound from a tape recorded with
the VCR is not in stereo or the
STEREO indicator in the display
window is flashing.
• Adjust the tracking.
• The video heads are dirty. Clean the video heads using a
Sony video head cleaning cassette as explained above.
Playback
Symptom
108
Troubleshooting
Recording
Remedy
• Make sure the TV is set to the video channel. If you are
using a monitor, set it to video input.
• Existing broadcasts may interfere with the VCR. Reset
the RF channel output of your VCR (page 15).
• Select the correct source with the INPUT SELECT
button. Select a programme position when recording TV
programmes; select a line input when recording from
other equipment.
TV reception is poor.
• Make sure the aerial cable is connected securely.
• Adjust the TV aerial.
The tape starts playing as soon as it is
inserted.
• The safety tab has been removed. To record on this tape,
cover the tab hole.
The tape is ejected when you press
z REC.
• The safety tab has been removed. To record on this tape,
cover the tab hole.
Nothing happens when you press
z REC.
• Make sure the tape is not at its end.
The timer does not operate.
•
•
•
•
•
•
•
•
•
The VPS/PDC function does not
operate properly.
• Check that the clock and the date are set correctly.
• Check that the PDC time you set is the correct one (there
might be a mistake in the TV programme guide). If the
broadcast you wanted to record did not send the good
PDC information, the VCR will not start recording.
• If the reception is poor, the PDC signal might be altered
and the VCR might not start recording.
A tape cannot be inserted.
• Check that a tape is not already in the tape compartment.
The selected input line connector
number does not appear in the
display window.
• Press INPUT SELECT to display the connected line.
The VCR mechanism needs to be
cleaned.
• Clean the cabinet, panel and controls with a dry, soft
cloth, or a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of solvent, such
as alcohol or benzine.
Check that the clock is set.
Make sure a tape has been inserted.
Check that the safety tab has not been removed.
Make sure the tape is not at its end.
Make sure a programme has been set for timer recording.
Make sure your timer settings are past the current time.
Check that the decoder is turned on.
Check that the satellite tuner is turned on.
The clock stops if the DVD-VCR is disconnected from
the mains for more than one minute. Reset the clock and
timer.
• Turn the power off and unplug the mains lead.
Additional Information
Others
Timer recording
Symptom
No TV programme appears on the
TV screen.
continued
Troubleshooting
109
Symptoms caused by contaminated video heads
• Normal picture
• Rough picture
initial
contamination
110
Troubleshooting
• Unclear picture
• No picture (or
black & white
screen appears)
terminal
Glossary
Chapter (page 31)
Sections of a picture or a music feature that
are smaller than titles. A title is composed of
several chapters. Depending on the disc, no
chapters may be recorded.
Dolby Digital (pages 53 and 56)
Digital audio compression technology
developed by Dolby Laboratories. This
technology conforms to 5.1-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. Dolby Digital provides the same
5.1 discrete channels of high quality digital
audio found in Dolby Digital cinema audio
systems. Good channel separation is realized
because all of the channel data are recorded
discretely and little deterioration is realized
because all channel data processing is digital.
Dolby Surround (Pro Logic) (page 52)
Audio signal processing technology that
Dolby Laboratories developed for surround
sound. When the input signal contains a
surround component, the Pro Logic process
outputs the front, centre and rear signals.
The rear channel is monaural.
The data capacity of a single-layer and
single-sided DVD is 4.7 GB (Giga Byte),
which is 7 times that of a CD. The data
capacity of a double-layer and single-sided
DVD is 8.5 GB, a single-layer and doublesided DVD is 9.4 GB, and double-layer and
double-sided DVD is 17 GB.
The picture data uses the MPEG 2 format,
one of the worldwide standards of digital
compression technology. The picture data is
compressed to about 1/40 (average) of its
original size. The DVD also uses a variable
rate coding technology that changes the data
to be allocated according to the status of the
picture. Audio information is recorded in a
multi-channel format, such as Dolby Digital,
allowing you to enjoy a more real audio
presence.
Furthermore, various advanced functions
such as the multi-angle, multilingual, and
Parental Control functions are provided with
the DVD.
DVD-RW (page 6)
A DVD-RW is a recordable and rewritable
disc that is the same size as a DVD VIDEO.
The DVD-RW has two different modes: VR
mode and Video mode. DVD-RWs created
in Video mode have the same format as a
DVD VIDEO, while discs created in VR
(Video Recording) mode allow the contents
to be programmed or edited.
Additional Information
DTS (page 56)
Digital audio compression technology that
Digital Theater Systems, Inc. developed.
This technology conforms to 5.1-channel
surround sound. The rear channel is stereo
and there is a discrete subwoofer channel in
this format. DTS provides the same 5.1
discrete channels of high quality digital
audio.
Good channel separation is realized because
all of the channel data is recorded discretely
and little deterioration is realized because all
channel data processing is digital.
DVD (page 6)
A disc that contains up to 8 hours of moving
pictures even though its diameter is the same
as a CD.
DVD+RW (page 6)
A DVD+RW (plus RW) is a recordable and
rewritable disc. DVD+RWs use a recording
format that is comparable to the DVD
VIDEO format.
continued
Glossary
111
Title (page 31)
The longest section of a picture or music
feature on a DVD, movie, etc., in video
software, or the entire album in audio
software.
Track (page 31)
Sections of a picture or a music feature on a
CD or VIDEO CD (the length of a song).
112
Glossary
Specifications
System
Laser
Semiconductor laser
Signal format system
PAL/(NTSC)
Channel coverage
PAL (I)
VHF IA to IJ, SA10 to SA13
UHF E21 to E69
CATV S01 to S05, S1 to S20
HYPER S21 to S41
RF output signal
UHF channels 21 to 69
Aerial out
75-ohm asymmetrical aerial socket
Tape speed
SP: PAL
23.39 mm/s (recording/playback)
NTSC 33.35 mm/s (playback only)
LP: PAL
11.70 mm/s (recording/playback)
NTSC 16.67 mm/s (playback only)
EP: NTSC 11.12 mm/s (playback only)
Maximum recording/playback time
10 hrs. in LP mode (with E300 tape)
Rewind time
Approx. 1 min. (with E180 tape)
Inputs and outputs
Timer section
Clock
Quartz locked
Timer indication
24-hour cycle
Timer setting
6 programs (max.)
General
Power requirements
220 – 240 V AC, 50 Hz
Power consumption
20 W
Operating temperature
5° C to 40° C
Storage temperature
–20° C to 60° C
Dimensions including projecting parts and controls
(w/h/d)
Approx. 430 × 85 × 287 mm
Mass
Approx. 3.9 kg
Supplied accessories
Remote commander (1)
R6 (size AA) batteries (2)
Aerial cable (1)
Audio cord (pinplug ×2 y pinplug ×2) (1)
Video cord (pinplug ×1 y pinplug ×1) (1)
Additional Information
LINE-1 (EURO AV)
21-pin
Video input: pin 20
Audio input: pins 2 and 6
Video output: pin 19
Audio output: pins 1 and 3
LINE-2 IN t/o L/R
VIDEO IN, phono jack (1)
Input signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO IN, phono jacks (2)
Input level: 327 mVrms
Input impedance: more than 47 kilohms
LINE-3
21-pin
Video input: pin 20
Audio input: pins 2 and 6
OUT
VIDEO OUT, phono jack (1)
Output signal: 1 Vp-p, 75 ohms, unbalanced, sync
negative
AUDIO OUT, phono jacks (2)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
Additional AUDIO OUT, phono jacks (2)
Standard output: 327 mVrms
Load impedance: 47 kilohms
Output impedance: less than 10 kilohms
DIGITAL OUT (OPTICAL)
Optical output jack/–18 dBm (wave length 660 nm)
DIGITAL OUT (COAXIAL)
Phono jack/0.5 Vp-p/75 ohms
S-VIDEO OUT
4-pin mini DIN/Y: 1.0 Vp-p, C: 0.3 Vp-p (PAL),
0.286 Vp-p (NTSC)/75 ohms
Design and specifications are subject to change without
notice.
Specifications
113
Index to parts and controls
Refer to the pages indicated in parentheses ( ) for details.
Front panel
A ?/1 (on/standby) switch (10) (29) (36)
I X (pause) button (28) (36)
B Disc tray (27)
J H (play) button*1 (28) (35)
C A (open/close) button (27) (28)
K
D Tape compartment (35)
L PROGRAM +/– buttons*1 (40)
E A (eject) button (36)
M SELECT DVD/VIDEO (9)
F z REC (record) button (40)
N LINE-2 IN t/o L/R jacks*2 (100)
G m (rewind)/M (fast-forward) buttons
(29) (36)
*1 H and PROGRAM + button has a tactile dot.
Use the tactile dot as a reference when operating
the DVD-VCR.
*2 Covered
H x (stop) button (28) (36)
114
Index to parts and controls
Remote sensor (9)
Display window
A DVD indicator (28)
F STEREO indicator (92)
B Record indicator (40)
C VIDEO indicator (35)
G Playing time/clock/current status
indicator (28) (35)
D Tape indicator (35)
H SURR (surround) indicator (77)
E Timer indicator (45)
I DTS indicator (56)
J Disc indicator (28)
Additional Information
continued
Index to parts and controls
115
Rear panel
DVD player and VCR
A Mains lead (11)
DVD player only
G LINE OUT AUDIO L/R jacks (54)
B OUT AUDIO L/R/VIDEO jacks (52)
H S-VIDEO OUT jack (54)
C
(in from aerial) connector (11)
D
(out to tv) connector (11)
I DIGITAL AUDIO OUT jack
(OPTICAL) (53)
E LINE-3 connector (13)
F LINE-1 (EURO AV) connector (12)
116
Index to parts and controls
J DIGITAL AUDIO OUT jack
(COAXIAL) (53)
Remote commander for DVD
A Z (open/close) button (27) (28)
B TV / DVD·VIDEO switch (9)
C SELECT DVD button (9)
D Number buttons* (10) (64)
E CLEAR button (24) (72)
F SURROUND button (77)
G SET UP button (15)
H SUBTITLE button (70)
I AUDIO button* (76)
J
SKIP button (28)
K
REPLAY button (28)
L X (pause) button (28)
M H (play) button* (28)
N V/v/B/b buttons
ENTER button (15) (55)
O DISPLAY button (31)
P TOP MENU button (66)
Q ?/1 (on/standby) switch (10) (29)
R VOL (volume) +/– buttons (10)
S ZOOM button (68)
T -/-- (ten’s digit) button (10)
U REPEAT button (71) (74)
V ANGLE button (69)
m/M y buttons (28) (29)
X . PREV (previous)/> NEXT
buttons (28)
Y x (stop) button (28)
Z O RETURN button (20) (32)
wj MENU button (66)
* Number 5, AUDIO and H buttons have a
tactile dot. Use the tactile dot as a reference
when operating the DVD-VCR.
Additional Information
W
continued
Index to parts and controls
117
Remote commander for VCR
A Z (eject) button (36)
B TV / DVD·VIDEO switch (9)
C SELECT VIDEO button (9)
D Number buttons* (10)
E CLEAR button (24) (37)
F SET UP button (15)
G TIMER button (47)
H AUDIO button* (92)
I
SKIP button (36)
J
REPLAY button (36)
K SP (Standard Play)/LP (Long Play)
button (40)
L z REC (record) button (40)
M X (pause) button (36)
N H (play) button* (35)
O V/v/B/b buttons
ENTER button (14) (44)
P DISPLAY button (41)
Q ?/1 (on/standby) switch (10) (36)
R PROG (programme)/TRACKING +/–
buttons* (40) (96)
S VOL (volume) +/– buttons (10)
T -/-- (ten’s digit) button (10)
U MUTING button (10)
V INDEX button (94)
W TV/VIDEO button (10)
X INPUT SELECT button (40)
Y m (rewind)/M (fast-forward)/
SLOW y buttons (36)
Z ./> SHUTTLE buttons (36)
wj x (stop) button (36)
wk O RETURN button (20) (97)
* Number 5, AUDIO, H and PROG/
TRACKING + buttons have a tactile dot. Use
the tactile dot as a reference when operating the
DVD-VCR.
118
Index to parts and controls
DVD Audio/Subtitle Language
Abbreviation
Language
ARA
Arabic
BUL
Bulgarian
CHI
Chinese
CRO
Croatian
CZE
Czech
DAN
Danish
DEU
German
ENG
English
ESP
Spanish
Finish
FRA
French
GRE
Greek
HUN
Hungarian
IDN
Indonesian
IND
Hindi
ISL
Icelandic
ITA
Italian
IWR
Hebrew
JPN
Japanese
KOR
Korean
MAL
Malay
NLD
Dutch
NOR
Norwegian
POL
Polish
POR
Portuguese
RUS
Russian
SVE
Swedish
THA
Thai
TUR
Turkish
VIE
Vietnamese
ZAF
Afrikaans
Additional Information
FIN
DVD Audio/Subtitle Language
119
Index
Numerics
I
R
16:9 59
4:3 Letter Box 59
4:3 Pan Scan 59
Index scan 94
Instant Advance 28
Instant Replay 28, 36
Instant Skip 36
Language selecting 16
LP mode 40
Recording 39
daily/weekly 49
quick timer recording 90
saving 42
using the VIDEO Plus+
system 43
while watching another
programme 41, 46, 49
Repeat play 74
RF channel 14, 15
Rotation 85
M
S
Manual fine tuning 21
Monaural 92
Monitoring
during playback 93
during recording 92
MP3 6, 79
Safety tab 42
Scart connection 12
Searching
at various speeds 29, 36
Shuffle play 73
Shuttle play 36
Slide show 86
Smart trilogic 96
SP mode 40
STEREO 76, 92
Subtitle 70
A
J
Adjusting
picture 96
tracking 96
Aerial hookup 11
Angle 69
Audio track 93
Auto Clock Set 14
Auto Set Up 14
JPEG 6, 84
L
C
Changing the programme
position 21
Changing the station name 25
Cleaning the video heads 108
Clock setting 17
Connecting
the DVD-VCR and your
TV 11
to a TV with a Scart
(EURO-AV) connector 12
to video equipment 100
Counter 37
Custom AV Mode 33
D
Daily/weekly recording 45
DATA CD 6, 79, 84
Disabling the programme
positions 23
DOLBY DIGITAL 52, 56, 76
DTS 53, 56, 76
DVD 6
E
Editing 100
EP mode 36
H
Handling discs 7
Hi-fi audio track 93
Sony Corporation
N
NICAM broadcasts 92
Normal audio track 93
P
Parental Control 63
PBC (Playback control) 88
PDC (Programme Delivery
Control) 45
Picture adjustment 96
Playback 27, 35
at various speeds 29, 36
JPEG image files 84
MP3 audio track 79
programme play 71
repeat play 74
selecting the sound 92, 93
shuffle play 73
shuttle play 36
skip 37
slow motion 29, 36
VIDEO CDs 88
Presetting channels 19
Programme play 71
Printed in Indonesia
T
Timer setting
quick timer recording 90
using the VIDEO Plus+
system 43
Tracking adjustment. see
Adjusting
U
Usable discs 6
V
VIDEO CD 6
VIDEO Plus+ recording 43
Z
Zoom 68, 85
AK68-00538X
">