Sony CDX-GT260 User manual

Sony CDX-GT260 User manual
CDX-GT21W/GT210/
GT260/GT260S
SERVICE MANUAL
US Model
Canadian Model
Ver. 1.2 2007.03
CDX-GT21W/GT210
E Model
CDX-GT260/GT260S
Chinese Model
CDX-GT260
• The tuner and CD sections have no adjustments.
AUDIO POWER SPECIFICATIONS (US, CND MODEL)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
23 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
Model Name Using Similar Mechanism
CDX-GT11W/GT110/
GT160/GT160S
CD Drive Mechanism Type
MG-101TA-188//Q
Optical Pick-up Name
DAX-25A
SPECIFICATIONS
CD player section
Signal-to-noise ratio
Frequency response
Wow and flutter
AM/MW
Tuning range
95 dB
10 – 20,000 Hz
Below measurable limit
Tuner section
FM
Tuning range
87.5 – 107.9 MHz (US, CND model)
87.5 – 108 MHz (at 50 kHz step) (E, CH model)
87.5 – 107.9 MHz (at 200 kHz step) (E, CH model)
FM tuning interval
50 kHz/200 kHz switchable (E, CH model)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
530 – 1,710 kHz (US, CND model)
531 – 1,602 kHz (at 9 kHz step) (E, CH model)
530 – 1,710 kHz (at 10 kHz step) (E, CH model)
AM tuning interval
9 kHz/10 kHz switchable (E, CH model)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
SW (E, CH model)
Tuning range
SW1: 2,940 – 7,735 kHz
SW2: 9,500 – 18,135 kHz
(except for 10,140 – 11,575 kHz)
Antenna (aerial) terminal
External antenna (aerial) connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
– Continued on next page –
FM/AM COMPACT DISC PLAYER
CDX-GT21W/GT210
FM/MW/SW COMPACT DISC PLAYER
CDX-GT260/GT260S
9-887-375-03
2007C04-1
© 2007.03
Sony Corporation
eVehicle Division
Published by Sony Techno Create Corporation
CDX-GT21W/GT210/GT260/GT260S
Power amplifier section
Outputs
Speaker outputs (sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output
50 W × 4 (at 4 ohms)
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.
General
Output
Inputs
TEST DISCS
Please use the following test discs for the check on the CD section.
Tone controls
Loudness
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Power antenna (aerial) relay control terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Low: ±10 dB at 100 Hz
High: ±10 dB at 10 kHz
+9 dB at 100 Hz
+5 dB at 10 kHz
12 V DC car battery (negative ground)
Approx. 178 × 50 × 179 mm
(7 1/8 × 2 × 7 1/8 in.) (w/h/d)
Approx. 182 × 53 × 162 mm
(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d)
Approx. 1.2 kg (2 lb. 11 oz.)
Parts for installation and connections (1 set)
Design and specifications are subject to change without
notice.
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical pickup block.
• Abbreviation
CND : Canadian model
CH : Chinese model
optical pick-up
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
semi-fixed resistor
SAFETY-RELATED COMPONENT WARNING!!
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
CDX-GT21W/GT210/GT260/GT260S
• CD Playback
You can play CD-DA (also containing CD TEXT*) and CD-R/
CD-RW (MP3/WMA files also containing Multi Session).
Type of discs
Label on the disc
SOLDER
• UNLEADED
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
CD-DA
MP3
WMA
* A CD TEXT disc is a CD-DA that includes information such as disc,
artist and track name.
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CNP301) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CNP301
J-2502-076-1
SERVO BOARD
CN2
3
CDX-GT21W/GT210/GT260/GT260S
Ver. 1.2
• E model
TABLE OF CONTENTS
1.
Location of Controls (CDX-GT21W: US) ......................
Connections (CDX-GT21W: US) ...................................
Location of Controls (CDX-GT21W: CND/GT210) ......
Connections (CDX-GT21W: CND/GT210) ....................
Location of Controls (CDX-GT260/GT260S) ................
Connections (CDX-GT260/GT260S) ..............................
This label is located on the bottom of the chassis.
• Chinese model
NOTE FOR REPLACEMENT OF THE SERVO BOARD
When repairing, the complete SERVO board (A-1177-201-A) should
be replaced since any parts in the SERVO board cannot be repaired.
NOTE FOR REPLACEMENT OF THE AUX JACK (J901)
To replace the AUX jack requires alignment.
1. Insert the AUX jack into the KEY board.
2. Place the KEY board on the front panel.
3. Solder the three terminals of the jack.
KEY board
GENERAL
5
5
7
7
9
9
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
Sub Panel (LCD) Assy ....................................................
CD Mechanism Block .....................................................
Main Board ......................................................................
Servo Board .....................................................................
Chassis (T) Sub Assy .......................................................
Roller Arm Assy ..............................................................
Chassis (OP) Assy ...........................................................
3.
DIAGNOSIS FUNCTION ........................................ 16
4.
DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
Block Diagram –Main Section– ......................................
Block Diagram –Display Section– ..................................
Printed Wiring Board –Main Section– ............................
Schematic Diagram –Main Section (1/3)– ......................
Schematic Diagram –Main Section (2/3)– ......................
Schematic Diagram –Main Section (3/3)– ......................
Printed Wiring Board –Key Section– ..............................
Schematic Diagram –Key Section– .................................
5.
EXPLODED VIEWS
12
12
13
13
14
14
15
19
20
21
22
23
24
25
26
5-1. Main Section .................................................................... 31
5-2. Front Panel Section ......................................................... 32
5-3. CD Mechanism Section (MG-101TA-188//Q) ................ 33
6.
AUX jack
front panel
4
ELECTRICAL PARTS LIST .................................. 34
CDX-GT21W/GT210/GT260/GT260S
SECTION 1
This section is extracted
GENERAL
from instruction manual.
• LOCATION OF CONTROL (CDX-GT21W: US)
Location of controls and basic operations
Main unit
12 3
4
5
6
7 8
OFF
PUSH SELECT
EQ
SEEK
SOURCE
AUX
SEEK
DIM
DSPL
MODE
ALBM
1
2
REP
SHUF
3
4
PAUSE
5
6
CDX-GT21W
9 q; qa qs
Refer to the pages listed for details.
A OFF button
To power off; stop the source.
B EQ (equalizer) button 8
To select an equalizer type (XPLOD,
NATURAL, HARD, UPBEAT, VOCAL,
CUSTOM or OFF).
C Volume control dial/select button 8
To adjust volume (rotate); select setup items
(press and rotate).
D SOURCE button
To power on; change the source (Radio/CD/
AUX).
E Disc slot
To insert the disc (label side up). Playback
starts automatically.
F Display window
G AUX input jack 9
To connect a portable audio device.
H Z (eject) button
To eject the disc.
I
qd
K SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fastforward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
L MODE button 7
To select the radio band (FM/AM).
M Number buttons
CD:
(1)/(2): ALBM –/+*
To skip albums (press); skip albums
continuously (press and hold).
(3): REP 7
(4): SHUF 7
(6): PAUSE
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
* When an MP3/WMA is played.
(front panel release) button 4
J DSPL (display)/DIM (dimmer) button
7
To change display items (press); change the
display brightness (press and hold).
6
• CONNECTIONS (CDX-GT21W: US)
Connection example
Ejemplo de conexiones
5
CDX-GT21W/GT210/GT260/GT260S
from car antenna (aerial)
desde la antena del automóvil
Fuse (10 A)
Fusible (10 A)
2
White
Blanco
Left
Izquierdo
Black
Negro
White/black striped
Con rayas blancas y negras
Gray
Gris
Right
Derecho
Blue
Azul
Gray/black striped
Con rayas grises y negras
Green
Verde
Left
Izquierdo
Red
Rojo
Green/black striped
Con rayas verdes y negras
Purple
Morado
Right
Derecho
Purple/black striped
Con rayas moradas y negras
Connection diagram
1 To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
2 To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
3 To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
4 To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker is not connected correctly, “FAILURE” appears in
the display. In this case, make sure the speaker is connected
correctly.
Diagrama de conexión
1 A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro,
y después los cables amarillo y rojo de fuente de
alimentación.
2 Al cable de control de la antena motorizada
o al cable de fuente de alimentación del
amplificador de señal de la antena
Notas
• Si no se dispone de antena motorizada ni de amplificador
de señal de la antena, o se utiliza una antena telescópica
accionada manualmente, no será necesario conectar este
cable.
• Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
3 Al terminal de alimentación de +12 V que
recibe energía en la posición de accesorio
del interruptor de la llave de encendido
Notas
• Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de +12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a
masa negro a una superficie metálica del automóvil.
• Si el automóvil incorpora una antena de FM/AM en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
4 Al terminal de alimentación de +12 V que
recibe energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de
alimentación
• El cable de control de la antena motorizada (azul) suministrará
cc de + 12 V cuando conecte la alimentación del sintonizador.
• Si el automóvil dispone de una antena de FM/AM incorporada
en el cristal trasero o lateral, conecte el cable de control de
antena motorizada (azul) o el cable de fuente de alimentación
auxiliar (rojo) al terminal de alimentación del amplificador de
señal de la antena existente. Para obtener más información,
consulte a su distribuidor.
• Con esta unidad no es posible utilizar una antena motorizada
sin caja de relé.
Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Notas sobre la conexión de los altavoces
• Antes de conectar los altavoces, desconecte la alimentación
de la unidad.
• Utilice altavoces con una impedancia de 4 a 8 Ω con la
capacidad de potencia adecuada para evitar que se dañen.
• No conecte los terminales de altavoz al chasis del automóvil,
ni conecte los terminales del altavoz derecho con los del
izquierdo.
• No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
• No intente conectar los altavoces en paralelo.
• Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplificadores incorporados) a los terminales de
altavoz, puede dañar la unidad.
• Para evitar fallas de funcionamiento, no utilice los cables de
altavoz incorporados instalados en el automóvil si su unidad
comparte un cable negativo común (–) para los altavoces
derecho e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz no está conectado correctamente, aparecerá
“FAILURE” en la pantalla. Si es así, compruebe la conexión del
altavoz.
6
ANT REM
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
Yellow
Amarillo
CDX-GT21W/GT210/GT260/GT260S
• LOCATION OF CONTROL (CDX-GT21W: CND/GT210)
Location of controls and basic operations
Main unit
12 3
4
5
6
7 8
OFF
PUSH SELECT
EQ
SEEK
SOURCE
AUX
SEEK
DIM
DSPL
MODE
ALBM
1
2
9 q; qa qs
Refer to the pages listed for details.
A OFF button
To power off; stop the source.
B EQ (equalizer) button 8
To select an equalizer type (XPLOD,
NATURAL, HARD, UPBEAT, VOCAL,
CUSTOM or OFF).
C Volume control dial/select button 8
To adjust volume (rotate); select setup items
(press and rotate).
D SOURCE button
To power on; change the source (Radio/CD/
AUX).
E Disc slot
To insert the disc (label side up). Playback
starts automatically.
F Display window
G AUX input jack 9
To connect a portable audio device.
H Z (eject) button
To eject the disc.
I
REP
SHUF
3
4
PAUSE
5
6
qd
CDX-GT210
CDX-GT21W
K SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fastforward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
L MODE button 7
To select the radio band (FM/AM).
M Number buttons
CD:
(1)/(2): ALBM –/+*
To skip albums (press); skip albums
continuously (press and hold).
(3): REP 7
(4): SHUF 7
(6): PAUSE
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
* When an MP3/WMA is played.
(front panel release) button 4
J DSPL (display)/DIM (dimmer) button
7
To change display items (press); change the
display brightness (press and hold).
6
• CONNECTIONS (CDX-GT21W: CND/GT210)
Connection example
Exemple de raccordement
7
CDX-GT21W/GT210/GT260/GT260S
from car antenna (aerial)
à partir de l’antenne du véhicule
Fuse (10 A)
Fusible (10 A)
2
White
Blanc
Left
Gauche
Black
Noir
White/black striped
Rayé blanc/noir
Gray
Gris
Right
Droit
Blue
Bleu
Gray/black striped
Rayé gris/noir
Green
Vert
Left
Gauche
Red
Rouge
Green/black striped
Rayé vert/noir
Purple
Violet
Right
Droit
Purple/black striped
Rayé violet/noir
Connection diagram
Schéma de raccordement
1 To a metal surface of the car
1 À un point métallique de la voiture
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
2 To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
3 To the +12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If there is no accessory position, connect to the +12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna (aerial) in
the rear/side glass, see “Notes on the control and power
supply leads.”
4 To the +12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner.
• When your car has built-in FM/AM antenna (aerial) in the rear/
side glass, connect the power antenna (aerial) control lead
(blue) or the accessory power supply lead (red) to the power
terminal of the existing antenna (aerial) booster. For details,
consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker is not connected correctly, “FAILURE” appears in
the display. In this case, make sure the speaker is connected
correctly.
Branchez d’abord le câble de mise à la masse noir et,
ensuite, les câbles d’alimentation jaune et rouge.
2 Vers le câble de commande d’antenne
électrique ou le câble d’alimentation de
l’amplificateur d’antenne
Remarques
• Il n’est pas nécessaire de raccorder ce câble s’il n’y a pas
d’antenne électrique ni d’amplificateur d’antenne, ou avec
une antenne télescopique manuelle.
• Si votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, voir « Remarques
sur les câbles de commande et d’alimentation ».
3 À la borne +12 V qui est alimentée quand la
clé de contact est sur la position accessoires
Remarques
• S’il n’y a pas de position accessoires, raccordez la borne
d’alimentation (batterie) +12 V qui est alimentée en
permanence.
Raccordez d’abord le câble de mise à la masse noir à un
point métallique du véhicule.
• Si votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, voir « Remarques
sur les câbles de commande et d’alimentation ».
4 À la borne +12 V qui est alimentée en
permanence
Raccordez d’abord le câble de mise à la masse noir à un
point métallique du véhicule.
Remarques sur les câbles de commande et d’alimentation
• Le câble de commande d’antenne électrique (bleu) fournit une
alimentation de +12 V CC lorsque vous mettez la radio sous
tension.
• Lorsque votre voiture est équipée d’une antenne FM/AM
intégrée dans la vitre arrière/latérale, raccordez le câble
de commande d’antenne électrique (bleu) ou le câble
d’alimentation des accessoires (rouge) à la borne
d’alimentation de l’amplificateur d’antenne existant. Pour plus
de détails, consultez votre détaillant.
• Une antenne électrique sans boîtier de relais ne peut pas être
utilisée avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le câble d’alimentation jaune est raccordé, le circuit
de la mémoire est alimenté en permanence même si la clé de
contact est sur la position d’arrêt.
Remarques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettez l’appareil hors
tension.
• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms
avec une capacité électrique adéquate pour éviter de les
endommager.
• Ne raccordez pas les bornes du système de haut-parleurs au
châssis de la voiture et ne raccordez pas les bornes du hautparleur droit à celles du haut-parleur gauche.
• Ne raccordez pas le câble de mise à la masse de cet appareil
à la borne négative (–) du haut-parleur.
• N’essayez pas de raccorder les haut-parleurs en parallèle.
• Raccordez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avec amplificateurs
intégrés) aux bornes des haut-parleurs peut endommager
l’appareil.
• Pour éviter tout dysfonctionnement, n’utilisez pas les câbles
des haut-parleurs intégrés installés dans votre voiture si
l’appareil partage un câble négatif commun (–) pour les hautparleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de
l’appareil.
Remarque sur le raccordement
Si les haut-parleurs ne sont pas raccordés correctement, le
message « FAILURE » s’affiche. Dans ce cas, assurez-vous que
les haut-parleurs sont bien raccordés.
8
ANT REM
Max. supply current 0.1 A
Courant max. fourni 0,1 A
Yellow
Jaune
CDX-GT21W/GT210/GT260/GT260S
• LOCATION OF CONTROL (CDX-GT260/GT260S)
Location of controls and basic operations
Main unit
12 3
4
5
6
7 8
OFF
PUSH SELECT
EQ
SEEK
SOURCE
AUX
SEEK
DIM
DSPL
MODE
ALBM
1
9 q; qa qs
2
qd
Refer to the pages listed for details.
A OFF button
To power off; stop the source.
B EQ (equalizer) button 8
To select an equalizer type (XPLOD,
NATURAL, HARD, UPBEAT, VOCAL,
CUSTOM or OFF).
C Volume control dial/select button 8
To adjust volume (rotate); select setup items
(press and rotate).
D SOURCE button
To power on; change the source (Radio/CD/
AUX).
E Disc slot
To insert the disc (label side up). Playback
starts automatically.
F Display window
G AUX input jack 9
To connect a portable audio device.
H Z (eject) button
To eject the disc.
I
(front panel release) button 4
J DSPL (display)/DIM (dimmer) button
7
To change display items (press); change the
display brightness (press and hold).
REP
SHUF
3
4
qf
PAUSE
5
CDX-GT260S
CDX-GT260
6
qg
K SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fastforward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
L MODE button 7
To select the radio band (FM/MW/SW).
M Frequency select switch (located on the
bottom of the unit)
See “Frequency select switch” in the
supplied installation/connections manual.
N Number buttons
CD:
(1)/(2): ALBM –/+*
To skip albums (press); skip albums
continuously (press and hold).
(3): REP 7
(4): SHUF 7
(6): PAUSE
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
O Receptor for the card remote
commander
* When an MP3/WMA is played.
6
• CONNECTIONS (CDX-GT260/GT260S)
Connection example
Ejemplo de conexiones
9
CDX-GT21W/GT210/GT260/GT260S
from car antenna (aerial)
desde la antena del automóvil
Fuse (10 A)
Fusible (10 A)
2
White
Blanco
Left
Izquierdo
Black
Negro
White/black striped
Con rayas blancas y negras
Gray
Gris
Right
Derecho
Blue
Azul
ANT REM
Gray/black striped
Con rayas grises y negras
Green
Verde
Left
Izquierdo
Max. supply current 0.1 A
Corriente máx. de alimentación de 0,1 A
Red
Rojo
Green/black striped
Con rayas verdes y negras
Purple
Morado
Yellow
Amarillo
Right
Derecho
Purple/black striped
Con rayas moradas y negras
Connection diagram
1 To a metal surface of the car
First connect the black ground (earth) lead, then connect the
yellow and red power supply leads.
2 To the power antenna (aerial) control lead or
power supply lead of antenna (aerial) booster
Notes
• It is not necessary to connect this lead if there is no power
antenna (aerial) or antenna (aerial) booster, or with a
manually-operated telescopic antenna (aerial).
• When your car has a built-in FM/MW/SW antenna (aerial)
in the rear/side glass, see “Notes on the control and power
supply leads.”
3 To the + 12 V power terminal which is
energized in the accessory position of the
ignition switch
Notes
• If there is no accessory position, connect to the + 12 V
power (battery) terminal which is energized at all times.
Be sure to connect the black ground (earth) lead to a
metal surface of the car first.
• When your car has a built-in FM/MW/SW antenna (aerial)
in the rear/side glass, see “Notes on the control and power
supply leads.”
4 To the + 12 V power terminal which is
energized at all times
Be sure to connect the black ground (earth) lead to a metal
surface of the car first.
Notes on the control and power supply leads
• The power antenna (aerial) control lead (blue) supplies + 12 V
DC when you turn on the tuner.
• When your car has built-in FM/MW/SW antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power supply lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker is not connected correctly, “FAILURE” appears in
the display. In this case, make sure the speaker is connected
correctly.
Diagrama de conexión
1 A una superficie metálica del automóvil
Conecte primero el cable de conexión a masa negro, y
después los cables amarillo y rojo de fuente de alimentación.
2
2 Al cable de control de la antena motorizada
o al cable de fuente de alimentación del
amplificador de señal de la antena
Notas
• Si no se dispone de antena motorizada ni de amplificador
de señal de la antena, o se utiliza una antena telescópica
accionada manualmente, no será necesario conectar este
cable.
• Si el automóvil incorpora una antena de FM/MW/SW en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
3 Al terminal de alimentación de + 12 V que
recibe energía en la posición de accesorio
del interruptor de la llave de encendido
Notas
• Si no hay posición de accesorio, conéctelo al terminal de
alimentación (batería) de + 12 V que recibe energía sin
interrupción.
Asegúrese de conectar primero el cable de conexión a
masa negro a una superficie metálica del automóvil.
• Si el automóvil incorpora una antena de FM/MW/SW en el
cristal trasero o lateral, consulte “Notas sobre los cables
de control y de fuente de alimentación”.
•
•
3
•
•
4
•
•
•
4 Al terminal de alimentación de + 12 V que
recibe energía sin interrupción
Asegúrese de conectar primero el cable de conexión a masa
negro a una superficie metálica del automóvil.
Notas sobre los cables de control y de fuente de
alimentación
• El cable de control de la antena motorizada (azul) suministrará
cc de + 12 V cuando conecte la alimentación del sintonizador.
• Si el automóvil dispone de una antena de FM/MW/SW
incorporada en el cristal trasero o lateral, conecte el cable
de control de antena motorizada (azul) o el cable de fuente
de alimentación auxiliar (rojo) al terminal de alimentación del
amplificador de señal de la antena existente. Para obtener más
información, consulte a su distribuidor.
• Con esta unidad no es posible utilizar una antena motorizada
sin caja de relé.
Conexión para protección de la memoria
Si conecta el cable de fuente de alimentación amarillo, el circuito
de la memoria recibirá siempre alimentación, aunque apague el
interruptor de encendido.
Notas sobre la conexión de los altavoces
• Antes de conectar los altavoces, desconecte la alimentación
de la unidad.
• Utilice altavoces con una impedancia de 4 a 8 Ω con la
capacidad de potencia adecuada para evitar que se dañen.
• No conecte los terminales de altavoz al chasis del automóvil,
ni conecte los terminales del altavoz derecho con los del
izquierdo.
• No conecte el cable de conexión a masa de esta unidad al
terminal negativo (–) del altavoz.
• No intente conectar los altavoces en paralelo.
• Conecte solamente altavoces pasivos. Si conecta altavoces
activos (con amplificadores incorporados) a los terminales de
altavoz, puede dañar la unidad.
• Para evitar fallos de funcionamiento, no utilice los cables de
altavoz incorporados instalados en el automóvil si su unidad
comparte un cable negativo común (–) para los altavoces
derecho e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz no está conectado correctamente, aparecerá
“FAILURE” en la pantalla. Si es así, compruebe la conexión del
altavoz.
10
1
•
•
•
•
•
•
•
•
CDX-GT21W/GT210/GT260/GT260S
Ver. 1.2
SECTION 2
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
SET
2-1.
SUB PANEL (LCD) ASSY
(Page 12)
2-2.
CD MECHANISM BLOCK
(Page 12)
2-3.
MAIN BOARD
(Page 13)
2-4.
SERVO BOARD
(Page 13)
2-5.
CHASSIS (T) SUB ASSY
(Page 14)
2-6.
ROLLER ARM ASSY
(Page 14)
2-7.
CHASSIS (OP) ASSY
(Page 15)
1. CHUCKING ARM SUB ASSY
(SUPPLEMENT-1 Page 1)
2. SLED MOTOR ASSY
(SUPPLEMENT-1 Page 2)
3. OPTICAL PICK-UP SECTION
(SUPPLEMENT-1 Page 3)
4. OPTICAL PICK-UP
(SUPPLEMENT-1 Page 3)
11
CDX-GT21W/GT210/GT260/GT260S
Note: Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL (LCD) ASSY
3 two claws
2 two claws
1 two screws
(+PTT 2.6 × 6)
4 sub panel (LCD) assy
2-2. CD MECHANISM BLOCK
7 CD mechanism block
6 bracket (CD)
5 two screws
(+PTT 2.6 × 4)
3
2 screw
(+PTT 2.6 × 6)
4 CNP301
1 screw
(+PTT 2.6 × 6)
12
CDX-GT21W/GT210/GT260/GT260S
2-3. MAIN BOARD
2 two screws
(+PTT 2.6 × 8)
4 two screws
(+P 2.6 × 8)
1 three screws
(+BTT)
5 two screws
(+PTT 2.6 × 12)
6 screw
(+PTT 2.6 × 8)
7 heat sink
8 MAIN board
3
insulating sheet
2-4. SERVO BOARD
WHT
RED
BLK
WHT
RED
BLK
RED
ORG
BLE
YEL
GRY
2 toothed lock screw
(M 1.7 × 2.5)
3 toothed lock screw
(M 1.7 × 2.5)
SERVO board
5 SERVO board
1 Remove the eleven solders.
4 optical pick-up (16 core)
(CN1)
claw
claw
13
CDX-GT21W/GT210/GT260/GT260S
2-5. CHASSIS (T) SUB ASSY
2 two precision screws
(+P 1.7 × 2.2)
1 two precision screws
(+P 1.7 × 2.2)
4 chassis (T) sub assy
3 claw
2-6. ROLLER ARM ASSY
5 roller arm assy
4 gear (RA1)
1 spring (RAL)
3 washer
2 spring (RAR)
14
CDX-GT21W/GT210/GT260/GT260S
Ver. 1.2
2-7. CHASSIS (OP) ASSY
6 chassis (OP) assy
1 tension spring (KF)
5
7 coil spring (damper) (natural)
8 coil spring (damper) (green)
4 slider (R)
3 lever (D)
2 gear (LE1)
15
CDX-GT21W/GT210/GT260/GT260S
SECTION 3
DIAGNOSIS FUNCTION
Description of the Diagnostics function:
4. Contents of each display mode
4-1. Reset count display mode
1. Setting the Diag display mode
With the power off, press the [4] button, [5] button, and [4] button
on the set body or the remote control (for more than 2 seconds)
in turn.
2. Canceling the Diag display mode
During the Diag function mode, press the [OFF] button.
3. Initial display in the Diag display mode.
Just when the Diag mode is entered, “reset count” is displayed.
The display mode is switched by each rotation of
M >/SEEK + or . m/SEEK – keys.
XX
Reset count
(in hexadecimal format)
Diag code
01: Reset count
4-2. Reset count by watchdog timer display mode
02
XX
Reset count
(in hexadecimal format)
Reset count display
01
01
Diag code
02: Number of resets by watchdog timer
XX
4-3. Number of connected units display mode
Reset count by watchdog timer display
02
XX
Number of connected units display
031
XXX
031
XXX
Show the number of connected units for
CD-C, MD-C and XM respectively from
the rightmost (in hexadecimal format).
Recency of information
1-3: 1 represents the latest.
Diag code
03: Number of connected unit.
Operating hours display
04
XXXX
The display mode is switched by each rotation of [2] or [1] keys
during the number of connected units display mode.
CD error information display
051
No. of connected units history 1 (latest) display
XX
031
OFFSET/FAILURE error display
XXX
No. of connected units history 2 display
061XXXXX
032
XXX
No. of connected units history 3 display
033
XXX
4-4. Operating hours display mode
04
XXXX
Operating hours
(in hexadecimal format)
Diag code
04: Operating hours
16
CDX-GT21W/GT210/GT260/GT260S
4-5. CD error information display mode
4-5-1. Error description
4-6. OFFSET/FAILURE error display mode
061XXXXX
051
XX
Error information
Error description Indication
Description
(in hexadecimal
1X
SERVO ERROR
format)
3X
LOADING ERROR
Recency of information
4X
TRACK JUMP
1-3: 1 represents the latest.
5X
TEXT ERROR
Diag code
FX
MECHA
ERROR
05: CD error information
Operating hours
Error description
(0: OFFSET, 1: FAILURE)
Recency of information
1-3: 1 represents the latest.
Diag code
06: OFFSET/FAILURE
The display mode is switched by each rotation of [2] or [1] keys
during the OFFSET/FAILURE error display mode.
4-5-2. Disc type and operating hours
051XXXXX
OFFSET/FAILURE error history 1 (latest) display
Disc type
Operating hours
Disc type
Recency of information
1-3: 1 represents the latest.
Diag code
05: CD error information
Indication
0
1
2
3
8
F
Disc type
MP3
WMA
AAC
ATRAC
CD/DA
UNKNOWN
The display mode is switched by each rotation of [2] or [1] keys
during the CD error information display mode.
061XXXXX
OFFSET/FAILURE error history 2 display
062XXXXX
OFFSET/FAILURE error history 3 display
063XXXXX
CD error info history 1 (latest)
Error description plus error details display
051
XX
CD error info history 1 (latest)
Disc type plus operating hours display
051XXXXX
CD error info history 2
Error description plus error details display
052
XX
CD error info history 2
Disc type plus operating hours display
052XXXXX
CD error info history 3
Error description plus error details display
053
XX
CD error info history 3
Disc type plus operating hours display
053XXXXX
17
CDX-GT21W/GT210/GT260/GT260S
MEMO
18
CDX-GT21W/GT210/GT260/GT260S
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM — MAIN SECTION —
ELECTRONIC VOLUME
IC401
AUX BUFFER
IC901
R-CH
J901
3
AUX
+
1
R-CH
+
14
12
POWER AMP/MULTIPLE
VOLTAGE REGULATOR
IC750
10 AUX-LCH
7 AUX-RCH
OUT-FL 13
TU1
(TUNER UNIT)
J1
(ANTENNA)
10
L-CH 4
R-CH 3
1 ANT
+
8 DN1
9 DN2
8
R-CH
R-CH
R-CH
AUDIO 8.3V
TU+5V
B.U 3.3V
10 VCC (8.3V)
11 TU-VDD (TU5V)
15 E2P-VDD
QUALITY 5
S-METER 6
TU-MUTE 7
E2P-SCL 16
E2P-SDA 17
11 IN-RL
OUT-FR 14
OUT-RR 12
4 TU-LCH
3 TU-RCH
R-CH (FRONT)
R-CH (REAR)
VOLATT
MUTE 16
MUTE
Q441
I2C-SCL
I2C-SDA
MUTE DRIVE
Q478,479
QUALITY
VSM
TUATT
38 QUALITY
39 VSM
12 TU ATT
EEP-SCL
EEP-SDA
I2C_CKO 33
I2C_SIO 34
2
10
R-CH
D479
4 SCL
2 SDA
FU601
I2C-SCL
I2C-SDA
VP 35
D511
B.UP+B 37
VOL ATT 9
86
5
26
8
AUDIO8.3V
SERVO3.3V
MECHA6V
PANEL+B
16 BEEP
22 STB
25 DIAG
30
31
33
34
SERVO3.3V
MECHA6V
PANEL+B
ACC DETECT
Q631
BATT
BATTERY LEVEL CHECK
Q580-582
D581
TU+5V
TU+5V REG
Q1,D1
AUDIO 8.3V
R-CH
D512
6
21
27
SYS_RST
EJECT_OK
BUS_ON
9
25
18
19
8
1,2
A_ATT
BU_IN
D_3.3V
A_3.3V
BU_3.3V
DR_6V
UNISO
UNISI
UNISCK
Z-MUTE
CD_ON
CDM_ON
• R-CH is omitted due to same as L-CH.
• Signal Path
: CD PLAY
D510
: FM
77 RESET
88 SYSRST
87 BUSON
SERVO 3.3V
BU_3.3V
MECHA 6V
: AM/MW/SW
: AUX
RESET
IC602
1 VOUT
VDD 2
BU 3.3V
CDX-GT21W/GT210/GT260/GT260S
19
7
15
BU IN 54
CD
MECHANISM
UNIT
(MG-101TA)
BATT
AUDIO 8.3V
D580
59
58
60
93
98
99
ANT-REM
BU 3.3V
ATT
BEEP
AMPSTB
DIAG
25 EEP_CKO
24 EEP_SIO
UNI_SO
UNI_SI
UNI_CLK
Z_MUTE
CD_ON
CDM_ON
16
BATT
B.U+3.3V
TEST IN 73
22
24
26
16
5
7
RL+
RL–
4
FR+
12
FR–
3
RR+
11
RR–
6
ANT-REM 27
ACC_IN 72
CNP301
11 AU_LCH
15 AU_RCH
FL+
FL–
BATT
I2C-SCL
I2C-SDA
SYSTEM CONTROL
IC501 (1/2)
9
OUT-RL+ 9
OUT-RL– 7
MUTE
Q461
B-CH
6 CD-LCH
5 CD-RCH
I2C-SCL
I2C-SDA
OUT-FL+ 5
OUT-FL– 3
12 IN-FL
OUT-RL 11
SCL 17
SDA 18
TU-SCL 13
TU-SDA 14
CN601
1
20 FIL
19
ACC
TEST
CDX-GT21W/GT210/GT260/GT260S
4-2. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL
IC501 (2/2)
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
DISPLAY CONTROL
IC901
40 KEYIN1
D503
KEY ACKNOWLEDGE
SWITCH
Q664
RE901
PUSH SELECT
(VOLUME)
LCD_SO 28
LCD_CKO 29
LCD_CE 27
52 KEY ACK
76 AD_ON
ROTARY
ENCODER
3
S1
|
|
34
S33 •
39
48 DI
47 CL
46 CE
COM4 35
|
|
COM1 38
DIMMER
41 KEYIN0
BACK LIGHT
KEY MATRIX
LSW903–910, S904
LSW901, 902, S901–903
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
1
2
LCD901
LIQUID
CRYSTAL
DISPLAY
PANEL
For schematic diagrams.
For printed wiring boards.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f
: internal component.
• C : panel designation.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
a
: Through hole.
•
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
PANEL+B
RE-0
RE-1
31 RE-IN0
32 RE-IN1
LED931
BACK
( LCDLIGHT
)
LSW901–910
BU+3.3V
S502
( FREQUENCY
)
SELECT
KEY
( ILLUMINATE
)
10K
•
•
•
•
3 AREASEL2
9K
DIMMER
SWITCH
Q931
GT260/GT260S
X502
32.768kHz
X501
18.432MHz
CN901
15
79 XOUT
80 XIN
BACK LIGHT
SWITCH
Q932
82 OSCIN
PANEL+B
LED861–865,
LED871–874
KEY
ILLUMINATE
GT260/GT260S
83 OSCOUT
CN701
15
7 NOSE_SW
REMOTE CONTROL
SIGNAL RECEIVER
IC971
SIRCS 64
2 OUT
GT21W/GT210
(
•
)
•
IR
GT260/GT260S
PANEL+B
LED941–945,
LED951–953
KEY
ILLUMINATE
(
•
•
)
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
A : B+ Line.
B : B– Line.
H : adjustment for repair.
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
) : AM/MW/SW
<
> : CD PLAY
∗ : Impossible to measure
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
Circled numbers refer to waveforms.
Signal path.
J : CD PLAY
F : FM
f : AM/MW/SW
L : AUX
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
C
Q
These are omitted
B E
BE C
These are omitted
ECB
These are omitted
• Waveforms
— MAIN Board —
1
2
IC501 ul (XOUT)
IC501 id (OSCOUT)
1Vp-p
32.768kHz
0.5 V/DIV, 20 µsec/DIV
CDX-GT21W/GT210/GT260/GT260S
20
20
3.1Vp-p
18.432MHz
1 V/DIV, 20 nsec/DIV
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
CDX-GT21W/GT210/GT260/GT260S
4-3. PRINTED WIRING BOARD — MAIN SECTION —
2
1
A
: Uses unleaded solder.
3
4
5
6
7
8
9
10
11
12
13
14
J1
(ANTENNA)
JC796
B
B14.4V
JC753
JC755
JC754
JC795
C775
CN601
C774
JW144
C764
JW9
C751
FU601
C771
C765
IC750
JW153
JC756
D704
R901
CN701
D719
R514
C305
C306
X502
D512
R518
C513
R529
C501
C512
C514
C509
JC501
D503
JC504
R565
R671
FMB4
R558
R503
R672
R533
C516
R504
R679
R547
C507
R663
R674
R632
JW65
JW62
R536
Q664
JW52
R543
R601
IC602
Q581
R541
Q582
FB606
R673
R585
R535
JW63
11
1-871-015-
KEY BOARD
CN901
(Page 25)
CDX-GT21W/GT210/GT260/GT260S
21
21
Ref. No.
D1
D479
D502
D503
D510
D511
D512
D580
D581
D601
D609
D617
D704
D719
D751
D752
D753
D754
D755
D756
D757
D758
D760
D762
D903
Location
F-3
F-6
I-7
J-5
G-8
G-6
I-8
G-11
F-11
C-10
D-8
C-9
J-3
J-4
D-7
D-7
D-6
D-7
D-6
D-6
D-6
D-6
D-8
D-9
I-2
IC401
IC501
IC602
IC750
IC901
E-3
H-6
I-9
B-6
H-3
Q1
Q431
Q441
Q451
Q461
Q478
Q479
Q580
Q581
Q582
Q631
Q664
F-3
C-4
C-3
C-4
D-4
E-6
E-5
F-11
I-10
I-10
H-10
J-7
JW119
R584
R542
R690
R517
C631
JW174
R540
JC533 R556
C519
R692
R568
R561
R583
R631
JW45
JW146
JW145
R633
R636
JW82
R519
D502
JW51
R563
C508
(CHASSIS)
A
D601
R609
JW21
JW26
81
80
X501
GT260/GT260S
J
R634
Q631
JW44
C522
31
C523
JW87
R521
R513
C917
C918
JW8
0
10
1
1
50
R510
30
R512
CD MECHANISM UNIT
(MG-101TA)
R578
R508
R567
R902
JW109
R509
IC
JW54
R505
JW171
D510
R676
C511
51
JW76
JW139
R566
D580
JW117
JC527
R502
JW138
D903
L501
R527
C504
JW68
R904
C902
C901
C903
JW70
R903
JW71
R905
R906
R511
R522
R911
R914
R913
R526
C510
JW74
R912
R570
JW154
R661
R907
FB308
R675
C503
FB501
JW108
IC901
R507
R506 R756
FMB3
R757
GT260/GT260S
R575
JW133
R664
JW155
C905
JW105
R537
R544
R910
R539
R524 R681
JW67
R577
JW40
R662
JW103
R557
JW122
JW104
10K
R677
GT21W/GT210
R534
JW80
JW121
I
R538
R550
C756
R532
JW168
D511
R551
Q580
FB309
R528
JW48
JW169
JW167
JW166
9K
JW123
JW156
H
FB604
R531
R546
JW83
R8
R548
50
R4
JW162
R9
JW161
JW160
R5
G
) S502
FB310
C312
JW149
(
JW90
R545
D581
JW115
R301
JW49
R13
FREQUENCY
SELECT
JW66
GT260/GT260S
C309
FB305
JW120
JW81
R12
C7
JW100
FB605
GT21W/GT210
JW89
JW150
Q1
JW106
FB307
JW99
JW72
FB1
FB303
JW28
L1
R3
JW101
JW97
C406
JW124
JW56
C5
C407
JW50
JW130
D1
R2
C308
R302
C310
JW96
R582
JW129
JW75
C422
D479
JW141
C6
C302
JW95
JW69
F
JW94
FB302
L301
JC681
JW30
C13
R479
C755
R752
R409
JW98
C343
C754
JW29
JW91
C423
JW137
JW5
Q478
R407
R1
C479
R408
JW163
C4
FB304
JW140
R403
JW27
Q479
JW93
C301
R406
• Semiconductor
Location
CNP301
JW118
IC401
JW164
C12
D752
JW23
C413
R402
D751
JW111
JW42
JW92
R401
JW39
C776
E
JW6
JW7
JW18
JW24
C412
C758
JW17
JW102
C401
JW10
JW32
C770
JW25
JW88
C8
JW31
C461
C404
C405
D762
JW20
C769
C431
C451
JW173
L601
D609
JW58
Q461
R461
C601
C602
D760
R441
JW107
TU1
JW172
R462
C750
D
D617
B14.4V
D754
R452
R451
C617
C623
C465
C441
JW2
D753
JC1
(CHASSIS)
JW1
JW3
JW16
D755
C462
JW11
C432
Q451
JW15
D758
C435
C455
JW13
R431
C763
D756
C442
JW12
JW22
R432
C445
C753
R442
C452
JW14
C622
JW142
JW143
C
Q431
D757
Q441
(11)
CDX-GT21W/GT210/GT260/GT260S
4-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 27 for IC Block Diagram.
TU1
JW107
IC B/D
FB1
C431
IC401
JC1
C401
R13
R12
R2
R3
J1
R432
C7
C413
C404
R451
C441
R441
Q451
C412
C406
C407
R9
R8
C5
R406
R402
R408
R403
R407
R409
C13
C422
R5
C4
R452
C451
Q431
C405
C8
JW102
C12
R431
R442
C423
R462
R4
C461
Q441
Q461
R461
QUALITY
R401
C6
R1
(Page 23)
IC901
D1
Q1
L1
Q479
R905
R907
R906
D479
R912
Q478
R911
R914
R910
C905
R913
C903
R904
C776
D903
R903 R902
C902
R901 C901
(Page 24)
CDX-GT21W/GT210/GT260/GT260S
22
22
C479
R479
CDX-GT21W/GT210/GT260/GT260S
4-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 28 for IC Block Diagram.
JC796
JC795
C775
C765
C764
C774
C751
D751
D752
D753
C750
IC B/D
D754
JC754
D755
C435 C432
JC755
D756
D757
C455 C452
IC750
CN601
D758
C445 C442
D760
C465 C462
(Page 22)
JC753
R609
C753
JC756
C763
C769
C754
R752
C755
C770
C771
L601
C602
JW111
C758
JW52
R633
R631
D609
R634
C631
R632
(Page 24)
CDX-GT21W/GT210/GT260/GT260S
23
FU601
C617
D762
C756
Q631
D617
23
C601
D601
CDX-GT21W/GT210/GT260/GT260S
• Refer to page 20 for Waveforms.
4-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 29 for IC Pin Descriptions.
(Page 22)
(Page 23)
JC527
D510
L301
JC681
CNP301
R578
FB304
C302
FB303
R679
JC533
C308
D512
C301
D511
R531
FB305
FB604
C310
R302
C343
FB310
FB309
R519
R533
R556
R690
R536
R558
FB307
R301
C312
C309
R692
R535
FB308
R528
C622
C509
R674
C507
D502
R543
R568
C623
FB605
JC501
C305
FB302
C306
R517
R672
R529 R518
R542
R636
R547
X502
C508
Q664
R563
X501
R561
R565
R508
D719
R567
C510
L501
D503
JC504
R509
JW140
CN701
C511
C514
R566
R505
R675
R673
R671
R676
IC602
R504
R503
IC501
R502
R539
R601
C512
C501
QUALITY
C516
FB606
(Page 26)
C519
C513
R527
R526
R681
R677
C918
C523
R540
R524
C917
C522
R541
D704
R585
R661
R584
Q581
R756
R557
R544
R757
R512
R570
C503
R510
R663 R522
R551
R550
R507
R537
R538
R548
JW141
Q582
R513
R534
R506
R532
R577
R575
CDX-GT21W/GT210/GT260/GT260S
24
D581
Q580
R662
R514
R546
FB501
R582
R521
R664
R545
D580
C504
R511
S502
24
R583
CDX-GT21W/GT210/GT260/GT260S
4-7. PRINTED WIRING BOARD — KEY SECTION —
2
1
: Uses unleaded solder.
3
4
5
6
7
8
9
10
11
12
13
14
A
LED944
GT21W/GT210
R962
R909
LED874
LED865
LED931
LCD901
LIQUID CRYSTAL DISPLAY PANEL
S904
LSW902
37
1
LSW905
DSPL/DIM
LSW906
LSW907
C971
LSW908
LSW909
LSW910
LED951–953
(VOLUME ILLMINATE)
R914
LED865, GT21W/GT210
LED945, GT260/GT260S
S904
MODE
E
1
2
4/SHUF
3/REP
R951
R910
R908
R866 R865
52
LED9
LSW902
LSW903
M>/
SEEK+
R907
LED873
LED9
R905
LED931
(LCD BACKLIGHT)
R947
LED872
LED871–874
(VOLUME ILLMINATE)
53
R948
LSW904
S901
R862
LED864
R881
R882
LSW901
GT21W/GT210
S903
R961
LED871
Z
R942
LED862
LED942 GT260/GT260S
GT21W/GT210
R944
D
LED862, GT21W/GT210
LED942 GT260/GT260S
(DISC–SLOT)
GT260/GT260S
LED951
R945
LED945
R903
LSW901
EQ
C
R902
R946
S902
LED864, GT21W/GT210
S903
SOURDE
LED941, GT260/GT260S
LED861, GT21W/GT210
S901
LED941
LED944, GT260/GT260S
LED863 GT21W/GT210
B
LSW904
.m/
SEEK-
LED861
GT260/GT260S
R975
LED943
R943
LED943,
LED863,
S902
OFF
5
IC971
GT260/GT260S
1-871-016-
11
(11)
6/PAUSE
(Page 21)
MAIN BOARD
CN701
A
R952
R911
R949
R992
F
R912
R913
R950
D993 D992 D991
D994
R993
1
R985
2
1
R921
R987
C986
C985
25
R981
GT260/GT260S
C984
J901
FB903
R974
J901
AUX
R933
R932
R982
R931
24
R904
13
H
12
R922
C983
R984 R986
37
IC901
D981
R901
R934
Q931
36
48
Q932
FB901 FB902
D903
C981
R979 R978
R977
RE901
D982
5
C987
G
4
GT260/GT260S
CN901
R988
3
GT21W/GT210
R884
R883
R861
R941
RE901
I
PUSH SELECT
(VOLUME)
1-871-016-
• Semiconductor Location
Ref. No.
D903
D981
D982
D991
D992
D993
D994
CDX-GT21W/GT210/GT260/GT260S
25
25
Location
G-11
H-10
H-10
G-9
G-9
G-9
G-13
Ref. No.
IC901
IC971
Location
G-8
D-13
LED861
LED862
LED863
LED864
LED865
A-14
B-8
A-2
B-5
C-5
Ref. No.
LED871
LED872
LED873
LED874
LED931
LED941
LED942
LED943
Location
B-3
C-2
C-4
D-3
C-13
A-14
B-8
A-1
Ref. No.
LED944
LED945
LED951
LED952
LED953
Location
B-4
C-4
B-3
C-4
C-3
Q931
Q932
G-7
G-6
11
(11)
CDX-GT21W/GT210/GT260/GT260S
4-8. SCHEMATIC DIAGRAM — KEY SECTION —
R975
R931
R941
LED944
R861
LED864
R943
R947
R949
R981
R951
LED951
R932
LSW901(2/2)
R942
R933
R945
R862
LED873
R982
LSW905(2/2)
LED871
R865
LSW903(2/2)
IC971
R961
LSW910(2/2)
R883
LED941
LED861
LED945
LED865
C971
LSW906(2/2)
LSW902(2/2)
R962
LED942
LSW904(2/2)
LED862
R946
R881
LSW909(2/2)
R866
C981
R987
D981
LSW907(2/2)
LED931
LED943
D982
R884
LED952
LED953
R985
IC901
R986
R988
C985
LSW908(2/2)
R984
C987
LED872
LED863
C983
C984
C986
R977
R978
R979
LED874
Q931
R944
R948
R950
R952
R934
R882
R993
Q932
R992
R974
CN901
D994
LCD901
RE901
D903
R922
R901
R902
R903
R921
R904
S903
LSW901(1/2)
R908
R909
S904
LSW905(1/2)
LSW902(1/2)
S902
R907
LSW904(1/2)
S901
R905
LSW907(1/2)
LSW908(1/2)
R913
R914
LSW910(1/2)
R912
LSW909(1/2)
R911
LSW906(1/2)
LSW903(1/2)
R910
D993
D992
D991
FB903
FB902
J901
FB901
(Page 24)
CDX-GT21W/GT210/GT260/GT260S
26
26
CDX-GT21W/GT210/GT260/GT260S
• IC BLOCK DIAGRAMS
FIL
GND
SDA
SCL
MUTE
VCC
OUT-FR
OUT-FL
OUT-RR
OUT-RL
IC401 BD3444FS-E2 (MAIN Board (1/3))
20
19
18
17
16
15
14
13
12
11
VCC
VCC/2
2
I C BUS
LOGIC
VCO
FADER
FADER
FADER
FADER
BASS:
• fc = 100Hz
• GAIN = ±20dB/1dB step
•Q=1
FADER:
0 – -62dB/1dB step
TREBLE:
• fc = 10kHz
• GAIN = ±20dB/1dB step
•Q=1
BASS/TREBLE
PRIMARY VOLUME
(+12dB – -20dB/1dB step)
MUTE
INPUT GAIN
(0 – -20dB/1dB step)
1
2
3
4
5
6
7
8
9
10
BUS-RCH
BUS-LCH
TU-RCH
TU-LCH
CD-RCH
CD-LCH
AUX-RCH
DN1
DN2
AUX-LCH
INPUT SELECTOR
27
CDX-GT21W/GT210/GT260/GT260S
IC750 TDA8588BJ/N2/R1 (MAIN Board (2/3))
TAB 1
2 SDA
OUT-FL- 3
I2C BUS
4 SCL
FL
OUT-FL+ 5
6 VP2
OUT-RL- 7
RL
8 PGND3
OUT-RL+ 9
PROTECTION/
DIAGNOSTIC
IN-RR 15
12 IN-FL
14 IN-FR
MUTE
S-GND 13
10 SVR
MUTE
IN-RL 11
16 BEEP
VP
OUT-RR+ 17
18 PGND2
RR
OUT-RR- 19
20 VP1
OUT-FR+ 21
FR
OUT-FR- 23
STANDBY/
MUTE
22 STB
CHIP DETECT/
DIAGNOSTIC
24 PGND1
BATTERY
DETECTION
DIAG 25
TEMPERATURE
PROTECTION
ENABLE
LOGIC
26 RST
ANT-REM 27
SWITCH
AMP-REM 29
SWITCH
28 CRES
REGULATOR
30 AUDIO8.3V
SERVO5V 31
MECH6V 33
32 GND
34 PANEL+B
VP 35
REFERENCE
VOLTAGE
B.UP+B 37
28
REGULATOR
36 CBU
LOADDUMP
PROTECTION
BACK-UP
SWITCH
CDX-GT21W/GT210/GT260/GT260S
• IC PIN DESCRIPTIONS
• IC501 MB90F045PF-G-9014-SPE1 (SYSTEM CONTROL) (MAIN BOARD (3/3))
Pin No.
Pin Name
I/O
Pin Description
1
AREASEL0
I
Destination setting pin
2
AREASEL1
I
Destination setting pin
3
AREASEL2
I
Frequency select signal input
4
B-OUT SEL
I
Blackout existence distinction signal input (L: blackout none, H: blackout)
5
BEEP
O
BEEP signal output
6
CYRIL_SEL
I
Distinction pin for Cyril word. (L: not for the Kiril word, H: for the Kiril word)
7
NOSE_SW
I
Front panel detaching detection signal input (L: Panel on, H: Panel off)
8
DIAG
I
Status signal input from power amplifier.
9
VOLATT
O
Electronic volume attenuate control signal output.
10
NCO
O
Not used. (Open)
11
VSS
—
Ground
12
TUATT
O
Tuner mute control signal output
13
NSMASK
O
Noise mask signal output
14
ILLUMI_SEL1
I
Illumination voltage setting pin
15
ILLUMI_SEL2
I
Illumination voltage setting pin
16, 17
NCO
O
Not used. (Open)
18 to 20
NCO
O
Not used. (Open)
Not used in this set. (Open)
21, 22
NCO
O
Not used. (Open)
23
VCC5
—
Power supply (+3.3V)
24
EEP_SIO
I/O
EEPROM bus serial data input/output
25
EEP_CKO
O
EEPROM bus serial clock output
26
AMPSTB
O
Power AMP standby signal output
27
LCD_CE
O
LCD driver chip enable signal output
28
LCD_SO
O
LCD driver serial data signal output
29
LCD_SCK
O
LCD driver serial clock signal output
30
RDS ON
O
RDS ON signal output
31
RE-IN0
I
Rotary encoder signal input 0
Not used in this set. (Open)
32
RE-IN1
I
Rotary encoder signal input 1
33
I2C_CKO
O
I2C bus serial clock signal output
34
I2C_SIO
I/O
I2C bus serial data signal input/output
35
DAVDD
—
A/D converter power supply (+3.3V)
36
AVRH
—
A/D converter external reference power supply (+3.3V)
37
DAVSS
—
A/D converter Ground
38
QUALITY
I
Noise detect signal input
39
VSM
I
S-meter voltage detect signal input
40
KEYIN1
I
Key signal input 1
41
KEYIN0
I
42
VSS
—
43
RC_IN0
I
Rotary commander key signal input
44 to 48
NCO
O
Not used. (Open)
49
MD0
I
Operation mode setting pin (Pull up)
50
MD1
I
Operation mode setting pin (Pull up)
51
MD2
I
Operation mode setting pin (Pull down)
Key signal input 0
Ground
Not used in this set. (Pull up)
52
KEYACK
I
Key acknowledgment detect signal input
53
TU_ATTIN
I
Tuner mute zero cross detect signal input
54
BUIN
I
Back-up power supply detect signal input
55
NCO
O
Not used. (Open)
56
DAVN
I
RDS data block synchronized detect signal input
Not used in this set. (Pull down)
Not used in this set. (Pull down)
29
CDX-GT21W/GT210/GT260/GT260S
Pin No.
Pin Name
I/O
57
NCO
O
Not used. (Open)
Pin Description
58
UNISI
I
S-BUS data signal input
59
UNISO
O
S-BUS data signal output
60
UNISCK
O
S-BUS clock signal output
61
CODEC_SEL
I
Codec select signal input (H: MP3, L: non-MP3)
62
KEYSEL
I
6key/8key distinction signal input (H: 8key, L: 6key)
63
NCO
O
Not used. (Open)
64
SIRCS
I
Remote control signal input
65 to 67
NCO
O
Not used. (Open)
68
FLASH_W
I
Memory mode select signal input
69, 70
NCO
O
Not used. (Open)
71
RC_IN1
I
Rotary commander shift key signal input
72
ACC_IN
I
Accessory power supply detect signal input
73
TESTIN
I
Test mode detect signal input
74
TELATT
I
Telephone attenuate detect signal input
Not used in this set. (Pull up)
Not used in this set. (Pull down)
75
NCO
O
Not used. (Open)
76
AD_ON
O
A/D converter power supply control signal output
77
RESET
I
System reset signal input
78
NCO
O
Not used. (Open)
79
XOUT
O
Sub clock signal output (32.768kHz)
80
XIN
I
81
VSS1
—
Sub clock signal input (32.768kHz)
Ground
82
OSCIN
I
Main clock signal input (18.432kHz)
83
OSCOUT
O
Main clock signal output (18.432kHz)
84
VCC3
—
Power supply (+3.3 V)
85
DEMOSEL
I
DEMO select signal input (H: DEMO on, L: DEMO off)
86
ATT
O
Audio mute control signal output
87
BUSON
O
BUS ON signal output
88
SYSRST
O
System reset signal output
89
NCO
O
Not used. (Open)
90, 91
NCO
O
Not used. (Open)
92
NCO
O
Not used. (Open)
93
Z-MUTE
I
CD zero cross mute detect signal input
94, 95
NCO
O
Not used. (Open)
96
MO-DISP
I
Motion display select signal input
97
DIM_SEL
I
Dimmer select signal input
30
Not used in this set. (Pull up)
(H: Motion display on, L: Motion display off)
Not used in this set. (Pull down)
98
CD_ON
I
CD mechanism servo power control request signal input
99
CDM_ON
I
CD mechanism deck power control request signal input
100
COL_SW
I
Illumination color select signal input
Not used in this set. (Pull down)
CDX-GT21W/GT210/GT260/GT260S
SECTION 5
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• Abbreviation
CND : Canadian model
•
•
•
5-1.
The components identified by
mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number
specified.
-XX and -X mean standardized parts, so
they may have some difference from the
original one.
Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
Accessories are given in the last of this parts list.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
MAIN SECTION
not supplied
A
MG-101TA-188//Q
#2
7
#1
#3
B
A
#5
FU601
#4
#3
4
#3
not supplied
5
not supplied
3
6
#1
TU1
not supplied
B
2
#1
not supplied
#1
1
Ref. No.
Part No.
Description
Remark
1
2
3
4
5
X-2148-752-1
2-583-939-01
X-2148-837-1
2-583-940-01
A-1202-238-A
PANEL (LCD) ASSY, SUB
SCREW (+B 2X4)
LOCK ASSY
SCREW (+BTT)
MAIN BOARD, COMPLETE (GT21W/GT210)
5
6
7
A-1202-280-A MAIN BOARD, COMPLETE (GT260/GT260S)
2-345-298-01 PLATE (TU), GROUND
1-792-194-71 CORD (WITH CONNECTOR) (POWER)
Ref. No.
Part No.
Description
Remark
FU601
TU1
TU1
#1
#2
1-532-877-11
A-3220-960-B
A-3220-961-B
7-685-792-09
7-685-790-01
FUSE (BLADE TYPE) (AUTO FUSE) 10A
TUNER UNIT (TUX-032) (GT260/GT260S)
TUNER UNIT (TUX-032) (GT21W/GT210)
SCREW +PTT 2.6X6 (S)
SCREW +PTT 2.6X4 (S)
#3
#4
#5
7-685-793-09 SCREW +PTT 2.6X8 (S)
7-685-795-09 SCREW +PTT 2.6X12 (S)
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
31
CDX-GT21W/GT210/GT260/GT260S
5-2.
FRONT PANEL SECTION
60
59
60
RE901
not supplied
not supplied
(KEY board)
58
57
J901
56
not supplied
LCD901
not supplied
61
not supplied
not supplied
52
not supplied
55
not supplied
54
51
53
Ref. No.
Part No.
Description
51
51
51
51
51
A-1202-240-A
A-1202-248-A
A-1202-282-A
A-1202-297-A
A-1211-686-A
PANEL COMPLETE ASSY, FRONT (GT21W:US)
PANEL COMPLETE ASSY, FRONT (GT210:US)
PANEL COMPLETE ASSY, FRONT (GT260)
PANEL COMPLETE ASSY, FRONT (GT260S)
PANEL COMPLETE ASSY, FRONT (GT21W:CND)
51
52
52
53
54
A-1211-689-A
X-2148-894-1
X-2148-897-1
3-251-320-01
X-2148-871-1
PANEL COMPLETE ASSY, FRONT (GT210:CND)
BUTTON ASSY (S) (GT21W/GT210/GT260)
BUTTON ASSY (S) (GT260S)
EMBLEM (NO. 2.5), SONY
PANEL SUB ASSY, FRONT (GT21W)
54
54
54
X-2148-873-1 PANEL SUB ASSY, FRONT (GT210)
X-2148-876-1 PANEL SUB ASSY, FRONT (GT260)
X-2148-877-1 PANEL SUB ASSY, FRONT (GT260S)
32
Remark
Ref. No.
Part No.
Description
Remark
55
56
57
58
59
X-2148-893-1
2-693-726-01
1-780-433-21
X-2148-892-1
2-683-832-01
KNOB (VOL) (SV) ASSY
SPRING (RELEASE)
CONDUCTIVE BOARD, CONNECTION
HOLDER (LCD) ASSY
PANEL (LCD), BACK
60
61
J901
LCD901
3-250-543-91
X-2148-896-1
1-820-624-11
1-802-231-11
RE901
1-479-902-11 ENCODER, ROTARY (PUSH SELECT (VOLUME))
SCREW (+B P-TITE M2)
CASE ASSY (for FRONT PANEL) (EXCEPT US)
JACK (SMALL TYPE) (VERTICAL) (AUX)
DISPLAY PANEL, LIQUID CRYSTAL
(GT260/GT260S)
LCD901 1-802-232-11 DISPLAY PANEL, LIQUID CRYSTAL
(GT21W/GT210)
CDX-GT21W/GT210/GT260/GT260S
Ver. 1.2
5-3.
CD MECHANISM SECTION
(MG-101TA-188//Q)
NOTE: Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP.
101
102
not supplied
not supplied
103
#6
#6
105
not supplied
not supplied
not supplied
not supplied
not supplied
104
not supplied
not supplied
not supplied
not supplied
107
106
106
Ref. No.
Part No.
Description
101
102
0 103
104
A-1177-168-A
A-1177-169-A
X-2149-672-1
2-626-869-01
MECHANICAL BLOCK ASSY
DAXEV//Q
SERVICE ASSY, OP (DAX-25A)
SCREW (M2X3), SERRATION
Remark
Ref. No.
105
106
107
#6
Part No.
Description
3-348-998-31
3-352-758-31
A-1177-201-A
7-627-000-08
SCREW (M1.4X2.5), TAPPING, PAN
SCREW (M1.7X2.5), TOOTHED LOCK
SERVO BOARD, COMPLETE
SCREW, PRECISION +P 1.7X2.2 TYPE3
Remark
33
CDX-GT21W/GT210/GT260/GT260S
SECTION 6
KEY
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Abbreviation
CND : Canadian model
Ref. No.
Part No.
•
•
•
•
Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
CAPACITORS
uF : µF
COILS
uH : µH
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
Description
Remark
KEY BOARD
**********
1-780-433-21 CONDUCTIVE BOARD, CONNECTION
< CAPACITOR >
C971
1-107-826-11 CERAMIC CHIP
0.1uF
C981
C983
C984
C985
1-107-826-11
1-107-826-11
1-107-826-11
1-131-664-11
0.1uF
0.1uF
0.1uF
0.15uF
10%
16V
(GT260/GT260S)
10%
16V
10%
16V
10%
16V
10%
10V
C986
C987
1-127-715-11 CERAMIC CHIP
1-162-964-11 CERAMIC CHIP
0.22uF
0.001uF
10%
10%
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
The components identified by
mark 0 or dotted line with mark.
0 are critical for safety.
Replace only with part number
specified.
16V
50V
Ref. No.
Part No.
Description
Remark
LED863 8-719-078-21 LED SML-310PTT86 (OFF) (GT21W/GT210)
LED864 8-719-078-21 LED SML-310PTT86 (SOURCE)
(GT21W/GT210)
LED865 8-719-078-21 LED SML-310PTT86 (MODE) (GT21W/GT210)
LED871 8-719-078-21 LED SML-310PTT86 (VOLUME ILLUMINATE)
(GT21W/GT210)
LED872 8-719-078-21 LED SML-310PTT86 (VOLUME ILLUMINATE)
(GT21W/GT210)
LED873 8-719-078-21 LED SML-310PTT86 (VOLUME ILLUMINATE)
(GT21W/GT210)
LED874 8-719-078-21 LED SML-310PTT86 (VOLUME ILLUMINATE)
(GT21W/GT210)
LED931 6-501-339-01 LED NESW505CT-AST (LCD BACK LIGHT)
LED941 8-719-053-09 LED SML-310VTT86 (Z) (GT260/GT260S)
LED942 8-719-053-09 LED SML-310VTT86 (DISC-SLOT)
(GT260/GT260S)
< CONNECTOR >
CN901
1-819-758-12 PLUG, CONNECTOR 15P
< DIODE >
D903
D981
D982
D991
D992
6-501-180-01
6-501-167-01
6-501-193-01
8-719-978-33
8-719-978-33
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-18B
UDZW-TE17-5.1B
1SS355WTE-17
DTZ-TT11-6.8B
DTZ-TT11-6.8B
D993
D994
8-719-978-33 DIODE DTZ-TT11-6.8B
8-719-978-33 DIODE DTZ-TT11-6.8B (GT260/GT260S)
< JUMPER RESISTOR >
FB901
FB902
FB903
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
1-216-295-11 SHORT CHIP
0
0
0
< IC >
IC901
IC971
6-710-047-01 IC LC75836WH-US-E
6-600-163-01 IC RS-770 (IR) (GT260/GT260S)
< LIQUID CRYSTAL DISPLAY >
LCD901 1-802-231-11 DISPLAY PANEL, LIQUID CRYSTAL
(GT260/GT260S)
LCD901 1-802-232-11 DISPLAY PANEL, LIQUID CRYSTAL
(GT21W/GT210)
< LED >
LED861 8-719-078-21 LED SML-310PTT86 (Z) (GT21W/GT210)
LED862 8-719-078-21 LED SML-310PTT86 (DISC-SLOT)
(GT21W/GT210)
34
LED943 8-719-053-09 LED SML-310VTT86 (OFF) (GT260/GT260S)
LED944 8-719-053-09 LED SML-310VTT86 (SOURCE)
(GT260/GT260S)
LED945 8-719-053-09 LED SML-310VTT86 (MODE) (GT260/GT260S)
LED951 8-719-053-09 LED SML-310VTT86 (VOLUME ILLUMINATE)
(GT260/GT260S)
LED952 8-719-053-09 LED SML-310VTT86 (VOLUME ILLUMINATE)
(GT260/GT260S)
LED953 8-719-053-09 LED SML-310VTT86 (VOLUME ILLUMINATE)
(GT260/GT260S)
< SWITCH >
LSW901 1-786-805-12 SWITCH, TACTILE (WITH LED) (EQ)
(GT260/GT260S)
LSW901 1-786-806-12 SWITCH, TACTILE (WITH LED) (EQ)
(GT21W/GT210)
LSW902 1-786-805-12 SWITCH, TACTILE (WITH LED) (DSPL/DIM)
(GT260/GT260S)
LSW902 1-786-806-12 SWITCH, TACTILE (WITH LED) (DSPL/DIM)
(GT21W/GT210)
LSW903 1-786-805-12 SWITCH, TACTILE (WITH LED)
(M >/SEEK+) (GT260/GT260S)
LSW903 1-786-806-12 SWITCH, TACTILE (WITH LED)
(M >/SEEK+) (GT21W/GT210)
LSW904 1-786-805-12 SWITCH, TACTILE (WITH LED)
(. m/SEEK–) (GT260/GT260S)
LSW904 1-786-806-12 SWITCH, TACTILE (WITH LED)
(. m/SEEK–) (GT21W/GT210)
LSW905 1-786-805-12 SWITCH, TACTILE (WITH LED) (1/ALBM –)
(GT260/GT260S)
LSW905 1-786-806-12 SWITCH, TACTILE (WITH LED) (1/ALBM –)
(GT21W/GT210)
CDX-GT21W/GT210/GT260/GT260S
KEY
Ref. No.
Part No.
Description
Remark
LSW906 1-786-805-12 SWITCH, TACTILE (WITH LED) (2/ALBM +)
(GT260/GT260S)
LSW906 1-786-806-12 SWITCH, TACTILE (WITH LED) (2/ALBM +)
(GT21W/GT210)
LSW907 1-786-805-12 SWITCH, TACTILE (WITH LED) (3/REP)
(GT260/GT260S)
LSW907 1-786-806-12 SWITCH, TACTILE (WITH LED) (3/REP)
(GT21W/GT210)
LSW908 1-786-805-12 SWITCH, TACTILE (WITH LED) (4/SHUF)
(GT260/GT260S)
Part No.
Description
Remark
R941
1-216-813-11 METAL CHIP
220
R942
1-216-813-11 METAL CHIP
220
R943
1-216-811-11 METAL CHIP
150
R943
1-216-812-11 METAL CHIP
180
R944
1-216-810-11 METAL CHIP
120
R944
1-216-811-11 METAL CHIP
150
R945
1-216-812-11 METAL CHIP
180
R946
1-216-811-11 METAL CHIP
150
R947
1-216-811-11 METAL CHIP
150
R947
1-216-812-11 METAL CHIP
180
< TRANSISTOR >
R948
1-216-810-11 METAL CHIP
120
8-729-027-44 TRANSISTOR DTC114TKA-T146
6-551-444-01 TRANSISTOR RT1N436C-TP-1
R948
1-216-811-11 METAL CHIP
150
R949
1-216-807-11 METAL CHIP
68
R949
1-216-809-11 METAL CHIP
100
R950
1-216-807-11 METAL CHIP
68
R950
1-216-809-11 METAL CHIP
100
R951
1-216-807-11 METAL CHIP
68
R951
1-216-809-11 METAL CHIP
100
R952
1-216-807-11 METAL CHIP
68
R952
1-216-809-11 METAL CHIP
100
R961
1-216-809-11 METAL CHIP
100
R962
1-216-809-11 METAL CHIP
100
R974
1-216-809-11 METAL CHIP
100
R975
1-216-809-11 METAL CHIP
100
R977
1-216-809-11 METAL CHIP
100
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT260/GT260S)
5%
1/10W
R978
R979
R981
R982
R984
1-216-809-11
1-216-809-11
1-216-811-11
1-216-811-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
150
150
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R985
R986
R987
R988
R992
1-216-821-11
1-216-821-11
1-216-857-11
1-216-840-11
1-216-864-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
1K
1K
1M
39K
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R993
1-216-864-11 SHORT CHIP
LSW908 1-786-806-12 SWITCH, TACTILE (WITH LED) (4/SHUF)
(GT21W/GT210)
LSW909 1-786-805-12 SWITCH, TACTILE (WITH LED) (5)
(GT260/GT260S)
LSW909 1-786-806-12 SWITCH, TACTILE (WITH LED) (5)
(GT21W/GT210)
LSW910 1-786-805-12 SWITCH, TACTILE (WITH LED) (6/PAUSE)
(GT260/GT260S)
LSW910 1-786-806-12 SWITCH, TACTILE (WITH LED) (6/PAUSE)
(GT21W/GT210)
Q931
Q932
Ref. No.
< RESISTOR >
R861
1-216-810-11 METAL CHIP
120
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT21W/GT210)
R862
1-216-810-11 METAL CHIP
120
R865
1-216-811-11 METAL CHIP
150
R866
1-216-810-11 METAL CHIP
120
R881
1-216-811-11 METAL CHIP
150
R882
1-216-810-11 METAL CHIP
120
R883
1-216-811-11 METAL CHIP
150
R884
1-216-810-11 METAL CHIP
120
R901
R902
1-216-820-11 METAL CHIP
1-216-821-11 METAL CHIP
820
1K
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT21W/GT210)
5%
1/10W
5%
1/10W
R903
R904
R905
R907
R908
1-216-821-11
1-216-822-11
1-216-823-11
1-216-820-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1.2K
1.5K
820
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R909
R910
R911
R912
R913
1-216-821-11
1-216-822-11
1-216-823-11
1-216-824-11
1-216-825-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1.2K
1.5K
1.8K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R914
R921
R922
R931
R932
1-216-827-11
1-216-295-11
1-216-295-11
1-216-812-11
1-216-812-11
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
3.3K
0
0
180
180
5%
1/10W
5%
5%
1/10W
1/10W
R933
R934
1-216-812-11 METAL CHIP
1-216-822-11 METAL CHIP
180
1.2K
5%
5%
1/10W
1/10W
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT260/GT260S)
0
35
CDX-GT21W/GT210/GT260/GT260S
KEY
Ref. No.
MAIN
Part No.
Description
Remark
< ROTARY ENCODER >
RE901
1-479-902-11 ENCODER, ROTARY (PUSH SELECT (VOLUME))
< SWITCH >
S901
1-786-653-11 SWITCH, TACTILE (Z)
S902
1-786-653-11 SWITCH, TACTILE (OFF)
S903
1-786-653-11 SWITCH, TACTILE (SOURCE)
S904
1-786-653-11 SWITCH, TACTILE (MODE)
*************************************************************
A-1202-238-A MAIN BOARD, COMPLETE (GT21W/GT210)
A-1202-280-A MAIN BOARD, COMPLETE (GT260/GT260S)
*********************
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-685-793-09 SCREW +PTT 2.6X8 (S)
7-685-795-09 SCREW +PTT 2.6X12 (S)
< CAPACITOR >
Ref. No.
Part No.
Description
C504
C507
C508
C509
C510
1-162-970-11
1-162-917-11
1-162-917-11
1-162-966-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
15PF
15PF
0.0022uF
0.01uF
10%
5%
5%
10%
10%
25V
50V
50V
50V
25V
Remark
C511
C512
C513
C514
C516
1-124-584-00
1-162-964-11
1-162-964-11
1-162-964-11
1-162-964-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.001uF
0.001uF
0.001uF
0.001uF
20%
10%
10%
10%
10%
10V
50V
50V
50V
50V
C519
C522
C523
C601
C602
1-107-826-11
1-162-970-11
1-162-970-11
1-131-868-81
1-165-319-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
0.01uF
0.01uF
3300uF
0.1uF
10%
10%
10%
20%
16V
25V
25V
16V
50V
C617
C622
C623
C631
C750
1-163-009-11
1-126-916-11
1-126-916-11
1-126-160-11
1-115-340-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
0.001uF
1000uF
1000uF
1uF
0.22uF
10%
20%
20%
20%
10%
50V
6.3V
6.3V
50V
25V
C751
C753
C754
C755
C756
1-115-340-11
1-128-551-11
1-124-257-00
1-162-964-11
1-127-715-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.22uF
22uF
2.2uF
0.001uF
0.22uF
10%
20%
20%
10%
10%
25V
63V
50V
50V
16V
C758
C763
C764
C765
C769
1-124-261-00
1-127-715-11
1-115-340-11
1-115-340-11
1-127-715-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.22uF
0.22uF
0.22uF
0.22uF
20%
10%
10%
10%
10%
50V
16V
25V
25V
16V
C770
C771
C774
C775
C776
1-127-715-11
1-127-715-11
1-115-340-11
1-115-340-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.22uF
0.22uF
0.22uF
0.001uF
10%
10%
10%
10%
10%
16V
16V
25V
25V
50V
C901
C902
C903
C905
C917
1-109-982-11
1-109-982-11
1-126-961-11
1-162-970-11
1-163-017-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
2.2uF
0.01uF
0.0047uF
10%
10%
20%
10%
10%
10V
10V
50V
25V
50V
C918
1-163-017-00 CERAMIC CHIP
0.0047uF 10%
50V
C4
C5
C6
C7
C8
1-126-947-11
1-126-947-11
1-162-970-11
1-162-970-11
1-107-826-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
47uF
0.01uF
0.01uF
0.1uF
20%
20%
10%
10%
10%
35V
35V
25V
25V
16V
C12
C13
C301
C302
C305
1-162-970-11
1-162-970-11
1-124-248-00
1-124-584-00
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.01uF
0.01uF
22uF
100uF
100uF
10%
10%
20%
20%
20%
25V
25V
25V
10V
10V
C306
C308
C309
C310
C312
1-162-970-11
1-162-970-11
1-162-966-11
1-162-966-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.0022uF
0.0022uF
0.01uF
10%
10%
10%
10%
10%
25V
25V
50V
50V
25V
C343
C401
C404
C405
C406
1-162-970-11
1-126-964-11
1-127-715-11
1-127-715-11
1-126-160-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
10uF
0.22uF
0.22uF
1uF
10%
20%
10%
10%
20%
25V
50V
16V
16V
50V
C407
C412
C413
C422
C423
1-126-160-11
1-126-934-11
1-162-970-11
1-216-864-11
1-216-864-11
ELECT
ELECT
CERAMIC CHIP
SHORT CHIP
SHORT CHIP
1uF
220uF
0.01uF
0
0
20%
20%
10%
50V
16V
25V
C431
C432
C435
C441
C442
1-126-964-11
1-165-908-11
1-165-908-11
1-126-964-11
1-165-908-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
1uF
1uF
10uF
1uF
20%
10%
10%
20%
10%
50V
10V
10V
50V
10V
CN601 1-774-701-21 PIN, CONNECTOR 16P
CN701 1-819-773-13 SOCKET, CONNECTOR 15P
CNP301 1-820-611-11 CONNECTOR, BOARD TO BOARD 28P
C445
C451
C452
C455
C461
1-165-908-11
1-126-964-11
1-165-908-11
1-165-908-11
1-126-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
1uF
10uF
1uF
1uF
10uF
10%
20%
10%
10%
20%
10V
50V
10V
10V
50V
D1
D479
D502
D503
D510
6-501-168-01
6-501-193-01
8-719-060-48
6-501-193-01
6-501-013-01
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-5.6B
1SS355WTE-17
RB751V-40TE-17 (GT260/GT260S)
1SS355WTE-17
BAT54ALT1G
C462
C465
C479
C501
C503
1-165-908-11
1-165-908-11
1-124-589-11
1-162-970-11
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
1uF
1uF
47uF
0.01uF
100uF
10%
10%
20%
10%
20%
10V
10V
16V
25V
10V
D511
D512
D580
D581
D601
6-500-335-01
6-501-051-01
6-501-171-01
6-501-180-01
8-719-049-38
DIODE
DIODE
DIODE
DIODE
DIODE
MC2838-T112-1
BAT54CLT1G
UDZW-TE17-7.5B
UDZW-TE17-18B
1N5404TU
36
< CONNECTOR >
< DIODE >
CDX-GT21W/GT210/GT260/GT260S
MAIN
Ref. No.
Part No.
Description
D609
D617
D704
D719
D751
6-501-170-01
6-501-180-01
6-501-170-01
6-501-180-01
6-501-362-01
DIODE
DIODE
DIODE
DIODE
DIODE
UDZW-TE17-6.8B
UDZW-TE17-18B
UDZW-TE17-6.8B
UDZW-TE17-18B
1A4-TA26
Remark
D752
D753
D754
D755
D756
6-501-362-01
6-501-362-01
6-501-362-01
6-501-362-01
6-501-362-01
DIODE
DIODE
DIODE
DIODE
DIODE
1A4-TA26
1A4-TA26
1A4-TA26
1A4-TA26
1A4-TA26
D757
D758
D760
D762
D903
6-501-362-01
6-501-362-01
6-501-362-01
6-501-362-01
6-501-170-01
DIODE
DIODE
DIODE
DIODE
DIODE
1A4-TA26
1A4-TA26
1A4-TA26
1A4-TA26
UDZW-TE17-6.8B
Ref. No.
Part No.
Description
Remark
< RESISTOR >
JW52
1-249-425-11 CARBON
4.7K
5%
1/4W
< COIL >
L1
L301
L501
L601
1-469-844-11
1-216-295-11
1-216-295-11
1-456-617-11
INDUCTOR
SHORT CHIP
SHORT CHIP
COIL, CHOKE
2.2uH
0
0
< TRANSISTOR >
Q1
Q431
Q441
Q451
Q461
6-551-431-01
8-729-027-44
8-729-027-44
8-729-027-44
8-729-027-44
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC6027T100-QR
DTC114TKA-T146
DTC114TKA-T146
DTC114TKA-T146
DTC114TKA-T146
Q478
Q479
Q580
Q581
Q582
8-729-027-43
8-729-027-23
8-729-027-43
1-801-806-11
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146
DTA114EKA-T146
DTC114EKA-T146
DTC144EKA
2SC1623-L5L6
Q631
Q664
8-729-120-28 TRANSISTOR 2SC1623-L5L6
8-729-027-23 TRANSISTOR DTA114EKA-T146
< FERRITE BEAD >
FB1
FB302
FB303
FB304
FB305
1-500-245-11
1-216-864-11
1-216-864-11
1-216-295-11
1-216-295-11
INDUCTOR, FERRITE BEAD
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
FB307
FB308
FB309
FB310
FB501
1-216-864-11
1-216-295-11
1-216-864-11
1-216-864-11
1-216-295-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
FB604
FB605
FB606
1-500-245-11 INDUCTOR, FERRITE BEAD
1-216-864-11 SHORT CHIP
0
1-216-864-11 SHORT CHIP
0
0
0
0
0
0
< RESISTOR >
R1
R2
R3
R4
R5
1-216-821-11
1-414-595-11
1-414-595-11
1-216-839-11
1-216-843-11
METAL CHIP
1K
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
METAL CHIP
33K
METAL CHIP
68K
5%
1/10W
5%
5%
1/10W
1/10W
1-216-839-11
1-216-843-11
1-414-595-11
1-414-595-11
1-216-821-11
METAL CHIP
33K
METAL CHIP
68K
INDUCTOR, FERRITE BEAD
INDUCTOR, FERRITE BEAD
METAL CHIP
1K
5%
5%
1/10W
1/10W
< IC >
R8
R9
R12
R13
R301
5%
1/10W
IC
IC
IC
IC
IC
R302
R401
R402
R403
R406
1-216-821-11
1-216-797-11
1-216-864-11
1-216-864-11
1-216-809-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
1K
10
0
0
100
5%
5%
1/10W
1/10W
5%
1/10W
< JUMPER RESISTOR >
R407
R408
R409
R431
R432
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R441
R442
R451
R452
R461
1-216-821-11
1-216-833-11
1-216-821-11
1-216-833-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
1K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
47
1K
1K
10K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
10K
100K
100K
0.5%
5%
5%
1/10W
1/10W
1/10W
< FUSE >
FU601
IC401
IC501
IC602
IC750
IC901
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
6-710-048-01
6-806-944-01
6-709-458-01
6-705-360-02
8-759-681-42
BD3444FS-E2
MB90F045PF-G-9014-SPE1
XC61CN2802NR
TDA8588BJ/N2/R1
NJM12902V(TE2)
< JACK >
J1
1-815-185-13 JACK (ANTENNA)
JC1
JC501
JC504
JC527
JC533
1-216-864-11
1-216-864-11
1-216-864-11
1-216-821-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
SHORT CHIP
0
0
0
1K
0
JC681
JC753
JC754
JC755
JC756
1-216-864-11
1-216-296-11
1-216-296-11
1-216-296-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
R462
R479
R502
R503
R504
1-216-833-11
1-216-805-11
1-216-821-11
1-216-821-11
1-218-871-11
JC795
JC796
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
0
0
R505
R506
R507
1-218-871-11 METAL CHIP
1-216-845-11 METAL CHIP
1-216-845-11 METAL CHIP
5%
1/10W
37
CDX-GT21W/GT210/GT260/GT260S
MAIN
Ref. No.
SERVO
Part No.
Description
R508
R509
R510
R511
R512
1-216-864-11
1-216-812-11
1-216-821-11
1-216-821-11
1-216-821-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
180
1K
1K
1K
Remark
R513
R514
R517
R518
R519
1-216-845-11
1-216-845-11
1-216-841-11
1-216-864-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
R521
R522
R524
R526
R527
1-216-825-11
1-216-825-11
1-216-845-11
1-216-845-11
1-216-845-11
R528
R529
R531
R532
R533
Ref. No.
Part No.
Description
R584
R585
R601
R609
R631
1-216-841-11
1-216-849-11
1-216-845-11
1-216-829-11
1-249-425-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
47K
220K
100K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/4W
Remark
1-216-841-11
1-216-841-11
1-216-829-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
47K
4.7K
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
100K
100K
47K
0
100K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R632
R633
R634
R636
R661
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R662
R663
R664
R671
R672
1-216-833-11
1-216-821-11
1-216-833-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
10K
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-216-845-11
1-216-821-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
1K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R673
R674
R675
R676
R677
1-218-871-11
1-216-845-11
1-216-821-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
1K
1K
1K
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R534
R535
R536
R537
1-216-833-11
1-216-833-11
1-216-833-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
10K
100K
R679
R681
R690
R692
R752
1-216-821-11
1-216-864-11
1-216-845-11
1-216-845-11
1-216-811-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
0
100K
100K
150
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R538
1-216-845-11 METAL CHIP
100K
5%
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT21W/GT210)
R756
R757
R901
R902
R903
1-216-841-11
1-216-864-11
1-216-817-11
1-216-817-11
1-216-834-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
0
470
470
12K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R904
R905
R906
R907
R910
1-216-834-11
1-216-841-11
1-216-841-11
1-216-845-11
1-216-789-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
12K
47K
47K
100K
2.2
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R911
R912
R913
R914
1-216-825-11
1-216-864-11
1-216-864-11
1-216-825-11
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
2.2K
0
0
2.2K
5%
1/10W
5%
1/10W
R539
R540
R541
R542
R543
1-216-845-11
1-216-845-11
1-216-845-11
1-216-864-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
100K
100K
100K
0
1K
R544
R545
1-216-821-11 METAL CHIP
1-216-845-11 METAL CHIP
1K
100K
R546
1-216-845-11 METAL CHIP
100K
R547
R548
1-216-864-11 SHORT CHIP
1-216-845-11 METAL CHIP
0
100K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
5%
1/10W
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT260/GT260S)
5%
1/10W
(GT260/GT260S)
R550
1-216-845-11 METAL CHIP
100K
R551
1-216-845-11 METAL CHIP
100K
R556
R557
R558
1-216-833-11 METAL CHIP
1-216-825-11 METAL CHIP
1-216-821-11 METAL CHIP
10K
2.2K
1K
5%
1/10W
(GT21W/GT210)
5%
1/10W
(GT21W/GT210)
5%
1/10W
5%
1/10W
5%
1/10W
R561
R563
R565
R566
R567
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R568
R570
R575
R577
R578
1-216-821-11
1-216-817-11
1-216-845-11
1-216-845-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
470
100K
100K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R582
R583
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
1K
5%
5%
1/10W
1/10W
38
< SWITCH >
S502
1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT)
(GT260/GT260S)
< TUNER UNIT >
TU1
TU1
A-3220-960-B TUNER UNIT (TUX-032) (GT260/GT260S)
A-3220-961-B TUNER UNIT (TUX-032) (GT21W/GT210)
< VIBRATOR >
X501
1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)
X502
1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
*************************************************************
A-1177-201-A SERVO BOARD, COMPLETE
**********************
*************************************************************
CDX-GT21W/GT210/GT260/GT260S
Ref. No.
Part No.
Description
Remark
MISCELLANEOUS
***************
7
1-792-194-71 CORD (WITH CONNECTOR) (POWER)
0 103
X-2149-672-1 SERVICE ASSY, OP (DAX-25A)
J901
1-820-624-11 JACK (SMALL TYPE) (VERTICAL) (AUX)
*************************************************************
ACCESSORIES
************
2-696-857-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(GT21W:US)
2-696-857-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH)
(GT21W:CND/GT210)
2-696-857-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH,
SIMPLIFIED CHINESE) (GT260/GT260S)
2-696-858-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
SPANISH) (GT21W:US)
2-696-858-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
FRENCH) (GT21W:CND/GT210)
2-696-858-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
SPANISH,SIMPLIFIED CHINESE)
(GT260/GT260S)
X-2148-896-1 CASE ASSY (for FRONT PANEL) (EXCEPT US)
*************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS
***************************************
151
152
153
154
155
X-3382-647-1
1-792-194-71
3-246-011-01
2-686-802-01
A-1082-993-A
156
3-259-776-01 SCREW (+K 5X8 TP)
151
FRAME ASSY, FITTING
CORD (WITH CONNECTOR) (POWER)
KEY (FRAME)
COLLAR
SCREW ASSY (BS4), FITTING (GT260/GT260S)
152
153
×2
154
155
156
×4
39
CDX-GT21W/GT210/GT260/GT260S
MEMO
40
CDX-GT21W/GT210/
GT260/GT260S
US Model
Canadian Model
CDX-GT21W/GT210
SERVICE MANUAL
E Model
CDX-GT260/GT260S
Chinese Model
Ver. 1.2 2007.03
CDX-GT260
SUPPLEMENT-1
File this supplement with the service manual.
Subject: Notes for removal of the OPTICAL PICK-UP added.
DISASSEMBLY
1. CHUCKING ARM SUB ASSY
3 chucking arm sub assy
1 spring
2
Note: Have this portion receive the chassis.
Note: Have this portion receive the chassis.
Note: Be careful not to touch the turn table.
9-887-375-81
CDX-GT21W/GT210/GT260/GT260S
2. SLED MOTOR ASSY
2 three serration screws
(M 2 × 3)
3 sled mtor assy
1 spring
turn table
spring
stand
Note:
Never remove these parts since they were adjusted.
stand
Note: Place the stand with care not to touch the turn table.
Note for Assembly
three serration screws
(M 2 × 3)
sled mtor assy
Note: Take care to prevent the chassis from being bent
when tightening the three machine screws.
2
CDX-GT21W/GT210/GT260/GT260S
3. OPTICAL PICK-UP SECTION
2 optical pick-up section
1
Note: Be careful not to touch the lens and hologram
terminal when removing the optical pick-up section.
4. OPTICAL PICK-UP
1 pan tapping screw
(M 1.4 × 2.5)
2 leaf spring (sub guide)
3 leaf spring (OP)
5 optical pick-up
4 lead screw assy
Notes for Assembly
Prevent the end of the
leaf spring (sub guide) from being
in contact with the OP slide base.
Prevent the end of the
leaf spring (sub guide) from being
in contact with the OP slide base.
There is space at the end of the
leaf spring (sub guide) to avoid
contact with the slide.
3
CDX-GT21W/GT210/GT260/GT260S
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.
Date
Description of Revision
1.0
2006.08
New
1.1
2006.12
Correction of disassembly of OPTICAL PICK-UP.
1.2
2007.03
Notes for removal of the OPTICAL PICK-UP added.
(SUPPLEMENT-1)
4
(ENG-07003)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement

Languages