Sony | XR-4803 | User's Manual | Sony XR-4803 User's Manual

XR-4803
SERVICE MANUAL
East European Model
Model Name Using Similar Mechanism
Tape Transport Mechanism Type
NEW
MG-25F-136
SPECIFICATIONS
– Continued on next page –
FM/MW/LW CASSETTE CAR STEREO
MICROFILM
TABLE OF CONTENTS
1.
GENERAL ................................................................... 3
2.
DISASSEMBLY ......................................................... 9
3.
ASSEMBLY OF MECHANISM DECK ........... 11
4.
MECHANICAL ADJUSTMENTS ....................... 14
5.
ELECTRICAL ADJUSTMENTS
Test Mode ........................................................................ 14
Tape Deck Section .......................................................... 14
Tuner Section .................................................................. 15
6.
DIAGRAMS
6-1.
6-2.
6-3.
6-4.
6-5.
IC Pin Function Description ........................................... 17
Printed Wiring Board – MAIN Section – ...................... 21
Schematic Diagram – MAIN Section – .......................... 23
Printed Wiring Board – PANEL Section – .................... 27
Schematic Diagram – PANEL Section – ....................... 29
7.
EXPLODED VIEWS ................................................ 33
8.
ELECTRICAL PARTS LIST ............................... 36
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
–2–
SECTION 1
GENERAL
–3–
This section is extracted from
instruction manual.
–4–
–5–
–6–
–7–
–8–
SECTION 2
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.
FRONT PANEL ASS’Y
1 Push the button
(release).
A
2 Remove the front panel ass’y
to the direction of the arrow A.
COVER ASS’Y
1
2
2
1
3 cover ass’y
2
1
–9–
SUB PANEL, MECHANISM DECK (MG-25F-136)
5 screw
(PTT2.6 × 6)
3 connector
(CN351)
6 mechanism deck
(MG-25F-136)
4 flexible flat cable
(CN301)
2 sub panel
1 three screws
(PTT2.6 × 8)
1 three screws
(PTT2.6 × 8)
MAIN BOARD, HEAT SINK
5 two screws
(PTT2.6 × 5)
5 three screws
(PTT2.6 × 10)
1 screw
(PTT2.6 × 8)
3 two ground point
screws
5 screw
(PTT2.6 × 8)
4 main board
6 heat sink
2 rubber cap (25)
1 two screws
(PTT2.6 × 8)
– 10 –
SECTION 3
ASSEMBLY OF MECHANISM DECK
Note: Follow the assembly procedure in the numerical order given.
7 Holder the hanger by bending the claw.
HOUSING
5 Fit projection on C part.
1 Install the catch to the hanger.
2 Install the hanger onto
two claws of the housing.
hanger
4 Fit claw on B part.
3 Put the housing
under A part.
6 Fit projection on D part.
housing
C part
8 Hold the hanger by
bending the claw.
D part
A part
B part
ARM (SUCTION)
2 Move the arm (suction) in the arrow
direction and fit on projection.
projection
1 Fit the arm (suction) on the shaft.
– 11 –
LEVER (LDG-A) / (LDG-B)
shaft A
shaft B
shaft C
shaft A
shaft B
1 Fit the lever (LDG-A) on
shafts A – C and install it.
3 type-E stop ring 2.0
2 Fit the lever (LDG-B) on
shafts A and B and
install it.
GEAR (LDG-FT)
gear (LDG-D)
6 polyethylene washer
hole
hole
5 gear (LDG-FT)
lever (LDG-A)
gear (LDG-FB)
4 Align hole in the gear (LDG-D)
with hole the lever (LDG-A).
1
2 tension spring (LD-2)
2 tension spring (LD-1)
– 12 –
3 Move the lever (LDG-B)
in the arrow direction.
GUIDE (C)
2 guide (C)
1 three claws
– 13 –
SECTION 4
MECHANICAL ADJUSTMENTS
SECTION 5
ELECTRICAL ADJUSTMENTS
1. Clean the following parts with a denatured-alcohol-moistened
swab:
playback head pinch roller
rubber belt
capstan
idler
2. Demagnetize the playback head with a head demagnetizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the power supply
voltage unless otherwise noted.
TEST MODE
This set have the test mode function. In the test mode, FM Auto
Scan/Stop Level and AM (MW) Auto Scan/Stop Level adjustments
can be performed easier than it in ordinary procedure.
• Torque Measurement
Mode
Torque Meter
Meter Reading
Forward
CQ-102C
30 – 65 g•cm
(0.42 – 0.90 oz•inch)
Forward
Back Tension
CQ-102C
0.5 – 4.5 g•cm
(0.01 – 0.06 oz•inch)
Reverse
CQ-102RC
30 – 65 g•cm
(0.42 – 0.90 oz•inch)
Reverse
Back Tension
CQ-102RC
0.5 – 4.5 g•cm
(0.01 – 0.06 oz•inch)
FF, REW
CQ-201B
60 – 200 g•cm
(0.83 – 2.78 oz•inch)
• Tape Tension Measurement
Mode
Tension Meter
Meter Reading
Forward
CQ-403A
more than 90 g
(more than 3.18 oz)
Reverse
CQ-403R
more than 90 g
(more than 3.18 oz)
<Set the Test Mode>
1. Set the “power select” switch (S501) is “A” position.
2. Turn ON the regulated power supply. (All LEDs on the set
lights up, and the clock is displayed.)
Note: Press the [OFF] button, if the clock is not displayed.
3.
4.
5.
6.
Push the preset [4] button.
Push the preset [5] button.
Press the preset [1] button for more than two seconds.
Then the display indicates all lights, the test mode is set.
<Release the Test mode>
1. Push the [OFF] button.
2. Return the “power select” switch (S501) to initially set position.
See the adjustment location from on page 16 for the
adjustment.
TAPE DECK SECTION
0 dB=0.775 V
Tape Speed Adjustment
Setting:
speed checker
or
frequency counter
test tape
WS-48A
(3 kHz, 0 dB)
4Ω
set
–
+
speaker out terminal
Procedure:
1. Put the set into the FWD PB mode.
2. Adjust adjustment resistor for inside capstan motor so that the
reading on the speed checker or frequency counter becomes in
specification.
Specification: Constant speed
Speed checker
–1.5 to +2.5%
Adjustment Location: See page 16.
– 14 –
Frequency counter
2,955 to 3,075 Hz
TUNER SECTION
FM Stereo Separation Adjustment
Setting:
[SOURCE] button: FM
0 dB=1 µV
Cautions during repair
When the tuner unit is defective, replace it by a new one because its internal block is difficult to repair.
FM RF signal
generator
1. FM Auto Scan/Stop Level Adjustment.
2. FM Stereo Separation Adjustment.
3. AM (MW) Auto Scan/Stop Level Adjustment.
+
–
set
Carrier frequency
Output level
Mode
Modulation
FM Auto Scan/Stop Level Adjustment
Setting:
[SOURCE] button: FM
: 98.0 MHz
speaker out terminal
: 70 dB (3.2 mV)
: stereo
: main: 1 kHz, 20 kHz deviation (26.7%)
sub: 1 kHz, 20 kHz deviation (26.7%)
19 kHz pilot: 7.5 kHz deviation (10%)
Procedure:
FM RF signal
generator
antenna jack (J1)
0.01 µF
set
Carrier frequency
Output level
Mode
Modulation
: 98.0 MHz
: 22 dB (12.6 µV)
: mono
: 1 kHz, 22.5 kHz deviation (30%)
Procedure:
1. Set to the test mode. (See page 14.)
2. Push the [SOURCE] button and set to FM.
FM
0
98.
Level meter
connection
Level meter
reading (dB)
L-CH
L-CH
A
R-CH
L-CH
B
Adjust RV4 on TU1
for minimum reading.
R-CH
R-CH
C
L-CH
R-CH
D
Adjust RV4 on TU1
for minimum reading.
Specification: Separation more than 28 dB
3. Adjust with the volume RV2 on TU1 so that the “FM” indication turns to “FMI” indication on the display window.
But, in case of already indicated “FMI”, turn the RV2 so that
put out light “I” indication and adjustment.
Adjustment Location: See page 16.
Display
FM
FM Stereo
signal generator
output channel
L-CH Stereo separation: A-B
R-CH Stereo separation: C-D
The separations of both channels should be equal.
Display
SHUF1
4 Ω
0.01 µF
Note: Adjust the tuner section in the sequence shown below.
SHUF1
level meter
antenna jack (J1)
0
98.
Adjustment Location: See page 16.
– 15 –
AM (MW) Auto Scan/Stop Level Adjustment
Make this adjustment after “FM Auto Scan/Stop Level Adjustment”.
Setting:
[SOURCE] and [MODE] button: MW
Adjustment Location:
—SET UPPER VIEW–
Tape Speed Adjustment
30 Ω 15 pF
65 pF
AM RF signal
generator
AM dummy antenna
(50 Ω)
Carrier frequency : 999 kHz
30% amplitude
modulation by
1 kHz signal
Output level
: 33 dB (44.7 µV)
set
antenna jack (J1)
TU1
Procedure:
1. Set to the test mode. (See page 14.)
2. Push the [SOURCE] button and set to FM.
3. Push the [MODE] button and set to MW.
Display
INTRO
SHUF1
MW
999
4. Adjust with the volume RV1 on TU1 so that the “MW” indication turns to “MWI” indication on the display window.
But, in case of already indicated “MWI”, turn the RV1 so that
put out light “I” indication and adjustment.
RV4 FM Stereo Separation Adjustment
Display
INTRO
SHUF1
RV2 FM Auto Scan/Stop Level Adjustment
RV1 AM (MW) Auto Scan/Stop Level Adjustment
999
– 16 –
SECTION 6
DIAGRAMS
6-1. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC501 µPD17707GC-529-3B9 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Function
1
AMSSEL
I
2
POS3
I
3
POS2
I
4
POS0
I
5
POS1
I
6
TAPEON
O
Tape system power supply on/off control signal output terminal “H”: tape on
7
CM ON
O
Capstan/reel motor (M901) drive signal output terminal “H”: motor on
8
LM LOD
O
Loading/tape operation motor control signal output to the MM1322XFBE (IC351)
(For the loading direction and forward side operation) *1
9
LM EJ
O
Loading/tape operation motor control signal output to the MM1322XFBE (IC351)
(For the eject direction and reverse side operation) *1
10
TUNON
O
Tuner system power supply on/off control signal output to the BA3918 (IC611)
11
FM ON
O
FM system power supply on/off control signal output to the BA3918 (IC611) “H”: FM on
12
PW ON
O
Main system power supply on/off control signal output to the BA3918 (IC611) “H”: power on
Setting terminal for the AMS selection fixed at “L”
Tape position detect input from tape operation switch on the mechanism block
“H”: tuner on
13
MUT
O
Line muting control signal output terminal “H”: line muting on
14
VOLCE
O
Chip enable signal output to the electrical volume (IC331)
15
VOLCKO
O
Serial data transfer clock signal output to the electrical volume (IC331)
16
VOLSO
O
Serial data output to the electrical volume (IC331)
17
AMPON
O
Standby control signal output to the power amplifier (IC751) “L”: standby
18
AMPMUT
O
Muting control signal output to the power amplifier (IC751) “L”: muting on
19
DX/LO
O
Local/DX selection signal output to the FM/AM tuner unit (TU1) “L”: DX, “H”: local
20
NCO
O
Not used (open)
21
GND
—
Ground terminal
22
DSTSEL
I
Destination setting terminal (fixed at center voltage)
23
D-BASS
I
D-BASS switch (SW951) input (A/D input)
24
KEYIN1
I
Key input terminal (A/D input)
6, INTRO 1, REPEAT 2, 3, BL SKIP 6, ATA 5, MTL 4 keys input (LSW921 to LSW927)
25
KEYIN0
I
Key input terminal (A/D input)
OFF, SOURCE, MODE *, + ) + SEEK AMS, – = 0 SEEK AMS, VOLUME –,
SEL, VOLUME +, ATT, DSPL, BTM, LCL keys input
(LSW901 to LSW909, LSW930, LSW911 and LSW912)
26
RC IN0
I
Rotary remote commander shift key A/D input terminal
27
VSM
I
FM and AM (MW/LW) signal meter voltage detection input from the FM/AM tuner unit (TU1)
28
AMIFIN
I
AM (MW/LW) intermediate frequency detection signal input from the FM/AM tuner unit (TU1)
29
FMIFIN
I
FM intermediate frequency detection signal input from the FM/AM tuner unit (TU1)
30
VDD2
—
31
FM OSC
I
FM local oscillator detection signal input from the FM/AM tuner unit (TU1)
32
AM OSC
I
AM (MW/LW) local oscillator detection signal input from the FM/AM tuner unit (TU1)
33
GND
—
Ground terminal
34
NCO
O
Not used (open)
35
EO1
O
Main charge-pump control signal output terminal
36
TEST0
I
Setting terminal for the test (fixed at “L”)
37
NCO
O
Not used (open)
38
SEKOUT
O
Seek control signal output to the FM/AM tuner unit (TU1)
39
MW SW
O
MW/LW selection signal output to the FM/AM tuner unit (TU1) “L”: MW, “H”: LW
40
BEEP
O
Beep sound output terminal
Power supply terminal (+5V)
– 17 –
Pin No.
Pin Name
I/O
41
KEYACK
I
Input of acknowledge signal for the key entry Acknowledge signal is input to accept function
and eject keys in the power off status On at input of “L”
42
BU IN
I
Battery detect signal input terminal “H”: battery on
43
MTLSEL
Function
I/O
METAL control in/out terminal
At initial mode: auto/manual mode selection input of METAL function “L”: manual mode
At manual mode: METAL on/off control signal output to the CXA2509AQ (IC301)
“H”: METAL on
At auto mode: input at MTLIN (pin %ª)
Dolby control in/out terminal
At initial mode: valid/invalid selection input of dolby function (“L” input: valid)
At normal mode: dolby on/off control signal output “H”: dolby on
Not used this function in this set (fixed at “H”)
44
DOLON
I/O
45
AMSIN
I
Whether a music is present or not from CXA2509AQ (IC301) is detected at auto music sensor
“L”: music is present, “H”: music is not present
46
ST
I/O
Input of FM stereo detection signal from FM/AM tuner unit (TU1), and output of forced
monaural control signal to FM/AM tuner unit (TU1) (Commonly used for stereo display input
and forced monaural output)
FM stereo detection at input of “L”, forced monaural at output of “L”
47
AMS ON
O
Tape auto music sensor control signal output to the CXA2509AQ (IC301)
“L” is output to lower the gain for audio level at FF/REW
48
N/R OUT
O
Forward/reverse direction control signal output to the CXA2509AQ (IC301)
“L: forward direction, “H”: reverse direction
49
TAPMUT
O
Tape muting on/off control signal output to the CXA2509AQ (IC301) “H”: tape muting on
50
ILLON
O
Power supply on/off control signal output terminal at the illumination and liquid crystal display
driver (IC901) “H”: power on
At power select switch (S501) on mode: “H” output at the accessory on
At power select switch (S501) off mode: “H” output at the power on
51
SD IN
I
Station detector detect input from the FM/AM tuner unit (TU1)
Stop level for SEEK, BTM, etc. is determined SD is present at input of “H”
52
NOSESW
I
Detects the removal of the attaching and removing type front panel block “L”: attaching
53
TELMUTE
I
Telephone muting signal input terminal At input of “L”, the signal is attenuated by –20 dB
Not used (fixed at “H”)
54
REL
I
Reel table rotation detect signal input from the take-up and supply reel sensor
55
ACCIN
I
Accessory detect signal input terminal “L”: accessory on
56
TESTIN
I
Setting terminal for the test mode “L”: test mode (normally fixed at “H”)
57
RC IN1
I
Rotary remote commander shift key A/D input terminal
58
PW SEL
I
Power select switch (S501) input terminal
“L”: position A (halt mode), “H”: position B (operation mode)
59
MTLIN
I
Input terminal to set whether the auto metal function is present or not
“L”: auto metal function is present (fixed at “H”)
60
ADON
O
Power supply on/off control signal output for the A/D conversion
61
KEYSEL
I
Setting terminal for the key (fixed at “H”)
62
SEKOUTSEL
I
Active selection terminal for the SEKOUT (pin #•) (fixed at “L”)
63
COLORSEL
I
Setting terminal for the illumination color “L”: amber, “H”: green Not used (fixed at “L”)
64
LCDCE
O
Chip enable output to the liquid crystal display driver (IC901)
65
LCDCKO
O
Serial data transfer clock signal output to the liquid crystal display driver (IC901)
66
LCDSO
O
Serial data output to the liquid crystal display driver (IC901)
67
LCDINH
O
Blank indicate control signal output to the liquid crystal display driver (IC901)
“L”: no display
68
UNICKI
I
Serial data reading clock signal input terminal for the unilink Not used (connected to pin &¡)
– 18 –
Pin No.
Pin Name
I/O
Function
69
UNISO
O
Serial data output terminal for the unilink
70
UNISI
I
Serial data input terminal for the unilink
71
UNICKO
O
Serial data transfer clock signal output terminal for the unilink
Not used (open)
Not used (fixed at “L”)
72
BUSON
O
Bus on/off control signal output terminal
Not used (pull up)
73
SYSRST
O
Reset signal output terminal
Not used (pull up)
74
VREG
O
CPU regulator output terminal
75
GND
—
Ground terminal
76
X OUT
O
Main system clock output terminal (4.5 MHz)
77
X IN
I
Main system clock input terminal (4.5 MHz)
78
CE
I
CPU chip enable signal input (fixed at “H”)
79
VDD1
—
80
RESET
I
“L”: reset
Connected to capacitor
Power supply terminal (+5V)
System reset signal input from the reset signal generator (IC551) and reset switch (S551)
“L” is input for several 100 msec after power on, then it changes to “H”
*1 loading/tape operation motor control
MODE
STOP
LOADING/
FORWARD
LM LOD (pin 8)
“L”
LM EJ (pin 9)
“L”
TERMINAL
Not used (connected to pin ^•)
EJECT/
REVERSE
BRAKE
“H”
“L”
“H”
“L”
“H”
“H”
– 19 –
• IC Block Diagrams – MAIN Board –
AUXIN2
DIREF
LINEOUT2
NC
26
25
24
23 22 21
8 OUT2
IN2 2
24dB
T2
VCC 3
+ –
20 MSMODE
– +
NR BIAS
PBFB2 31
PBRIN2 32
MS
MODE
X1
TAPE/AUX
VCT 35
PBGND 36
VCT
MS ON/ 15 NC
OFF
DETECT
VCC
+
LPF
+
–
14 MSOUT
PBFIN1 37
F3
F1
PBREF1 38
13 DGND
X1
PBRIN1 39
PBFB1 40
12 MSTC
+ –
8
9
NC
NC
6
10
G2FB
7
LINEOUT1
24dB
MSLPF
4 5
TAPEIN1
AUXIN1
PBOUT1
3
VCC
2
PBEQ1
120µ/70µ
1
11 G1FB
– +
T1
LVRIN
LCOM
LT1
LT2
LT3
LTOUT
LSIN
LS1
LS2
LS3
LSOUT
LC75373ED
33
32
31 30
29
28 27 26
25 24
23
+
–
+
–
34
35
36
37
38
–
+
–
+
+
–
22 LFIN
–
+
–
+
LSELO
L4
L3
L2
L1
5 GND
16 NC
FWD/RVS
+
–
21 LFOUT
+
–
20 LROUT
19 VREF
VDD 39
–
+
DECODER
–
+
40
41
42
43
44
LATCH
SHIFT
REGISTER
+
–
–
+
+
–
–
+
CONTROL
–
+
+
–
18
17
16
15
CE
DI
CL
VSS
14 RROUT
13 RFOUT
1
2
3 4
5
6 7 8
9 10
11
RT1
RT2
RT3
RTOUT
RSIN
RS1
RS2
RS3
RSOUT
12 RFIN
RCOM
–
+
RVRIN
R1
R2
R3
R4
RSELO
– 31 –
7 VS
6 OUT1
18 TAPESW
17 INSW
TAPE EQ
PBFIN2 34
IN1 4
19 DRSW
F2
PBREF2 33
CONTROL CIRCUIT
TAPEIN2
28 27
GND 1
MSSW
GND
29
NC
PBOUT2
30
120µ/70µ
IC331
MM1322XFBE
CXA2509AQ-T4
PBEQ2
IC301
IC351
IC611
BA3918-V2
REGULATOR
OVER VOLTAGE
PROTECT
VCC
10
11
12
GND
VDD
AMP
9
FM
NC
8
AM
7
ANT
6
COM
5
MODE2
MODE1
STB
+
–
2 3 4
+
–
1
+
–
–
+
– 32 –
SECTION 7
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑
↑
Parts Color Cabinet's Color
• Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering
these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Hardware (# mark) list and accessories and
packing materials are given in the last of the
electrical parts list.
(1) CHASSIS SECTION
8
14
15
MG-25F-136
#3
F781
9
7
10
6
#2
#4
#2
#2
5
11
12
4
3
#2
2
13
#1
#2
#2
1
Front panel ass’y
Ref. No.
Part No.
Description
1
2
3
4
* 5
3-009-294-01
3-935-003-01
3-932-205-21
X-3367-636-1
3-010-377-01
PANEL, SUB
SPRING, TORSION
DOOR, CASSETTE
LOCK ASSY
INSULATOR
* 6
7
* 8
A-3313-396-A MAIN BOARD, COMPLETE
3-915-923-01 SCREW, GROUND POINT
X-3373-270-1 COVER ASSY
Remark
Ref. No.
Part No.
Description
9
* 10
* 11
12
* 13
1-776-207-41
3-009-809-01
3-010-517-01
3-935-014-01
3-009-813-01
CORD (WITH CONNECTOR) (POWER)
BRACKET (IC)
HEAT SINK (BUS NON) (E)
CUSHION (U)
CHASSIS
14
15
F781
– 33 –
Remark
3-012-859-01 CAP (25), RUBBER
3-937-650-01 PLATE (C), GROUND
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)
(2) FRONT PANEL SECTION
102
#5
not supplied
(KEY board)
#5
108
109
117
120
107
118
116
106
105
111
115
114
121
LCD901
112
104
103
113
101
Ref. No.
101
102
103
104
105
* 106
107
108
109
111
Part No.
Description
3-018-799-01
3-015-036-01
3-016-924-01
3-009-304-01
3-932-475-01
BUTTON (D-BASS)
CUSHION (BACK PANEL)
BUTTON (L) (2) (+. –)
BUTTON (RELEASE)
SPRING (RELEASE)
Remark
3-019-149-01 PLATE, LCD
X-3374-689-1 PANEL SUB ASSY
3-009-300-01 BUTTON (SOURCE)
3-018-797-11 BUTTON (L) (3)
(+ + ). SEEK AMS. = 0 –. r. OFF. SEL. ATT)
3-016-927-01 BUTTON (1-3) (6. 1. 2. 3)
Ref. No.
Part No.
Description
112
113
* 114
* 115
* 116
3-016-928-11
3-016-930-01
3-019-151-01
3-019-150-01
3-018-612-01
BUTTON (4-6) (4. 5. 6)
BUTTON (R) (3) (BTM. LCL. r)
PLATE (LCD), GROUND
SHEET (REFLECTOR)
PLATE, LIGHT GUIDE
* 117
118
* 120
* 121
LCD901
3-018-611-01
3-010-519-01
3-024-391-01
3-024-846-01
1-801-966-11
HOLDER (LCD)
PANEL, FRONT BACK
SHEET (LCD)
SHEET (LCD) B
DISPLAY PANEL, LIQUID CRYSTAL
– 34 –
Remark
(3) MECHANISM DECK SECTION
(MG-25F-136)
160
159
163
158
A
155
161
HP901
154
162
157
#6
M901
156
A
164
153
152
165
#7
168
168
166
167
151
Ref. No.
Part No.
Description
151
* 152
* 153
154
155
A-3291-667-A
3-019-130-01
3-019-131-01
3-020-539-01
3-020-540-01
CLUTCH (FR) ASSY
LEVER (LDG-A)
LEVER (LDG-B)
SPRING (LD-1), TENSION
SPRING (LD-2), TENSION
156
157
158
* 159
160
3-020-542-01
3-341-753-11
3-020-533-01
3-020-532-01
3-020-534-01
GEAR (LOADING FT)
WASHER, POLYETHYLENE
HOUSING
ARM (SUCTION)
HANGER
Remark
Ref. No.
Part No.
Description
161
162
163
164
165
3-933-346-01
3-933-344-01
3-014-798-01
3-364-151-01
A-3301-267-A
CATCHER
GUIDE (C)
SCREW (HEAD), SPECIAL
WASHER
CHASSIS ASSY (F)
166
167
168
HP901
M901
3-017-302-01
3-936-853-01
3-701-437-21
1-500-157-21
A-3291-665-A
BELT (25)
FLYWHEEL (F)
WASHER
HEAD, MAGNETIC (PLAYBACK)
MOTOR ASSY, MAIN (CAPSTAN/REEL)
– 35 –
Remark
SECTION 8
ELECTRICAL PARTS LIST
KEY
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts specified in the diagrams or the components used
on the set.
• -XX and -X mean standardized parts, so they
may have some difference from the original
one.
• RESISTORS
All resistors are in ohms.
METAL: Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F: nonflammable
Ref. No.
Part No.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• SEMICONDUCTORS
In each case, u: µ, for example:
uA. .
: µA. .
uPA. . : µPA. .
uPB. . : µPB. .
uPC. . : µPC. .
uPD. . : µPD. .
• CAPACITORS
uF: µF
• COILS
uH: µH
Description
Remark
KEY BOARD
**********
3-018-611-01
3-018-612-01
3-019-149-01
3-019-150-01
3-019-151-01
*
*
*
*
*
HOLDER (LCD)
PLATE, LIGHT GUIDE
PLATE, LCD
SHEET (REFLECTOR)
PLATE (LCD), GROUND
< CAPACITOR >
C901
C902
C903
C904
1-163-033-00
1-165-319-11
1-165-319-11
1-163-137-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.1uF
0.1uF
680PF
5%
50V
50V
50V
50V
Ref. No.
When indicating parts by reference
number, please include the board.
Part No.
Description
Remark
LSW906
LSW907
LSW908
LSW909
LSW911
1-762-619-11
1-762-619-11
1-762-619-11
1-762-619-11
1-762-619-11
SWITCH, KEY BOARD (WITH LED) (–)
SWITCH, KEY BOARD (WITH LED) (SEL)
SWITCH, KEY BOARD (WITH LED) (+)
SWITCH, KEY BOARD (WITH LED) (ATT)
SWITCH, KEY BOARD (WITH LED) (BTM)
LSW912
LSW921
LSW922
LSW923
LSW924
1-762-619-11
1-762-619-11
1-762-619-11
1-762-619-11
1-762-619-11
SWITCH, KEY BOARD (WITH LED) (LCL)
SWITCH, KEY BOARD (WITH LED) (6)
SWITCH, KEY BOARD (WITH LED) (1/INTRO)
SWITCH, KEY BOARD (WITH LED) (2/REPEAT)
SWITCH, KEY BOARD (WITH LED) (3)
LSW925
LSW926
LSW927
LSW930
1-762-619-11
1-762-619-11
1-762-619-11
1-762-619-11
SWITCH, KEY BOARD (WITH LED) (6/BL SKIP)
SWITCH, KEY BOARD (WITH LED) (5/ATA)
SWITCH, KEY BOARD (WITH LED) (4/MTL)
SWITCH, KEY BOARD (WITH LED) (DSPL)
< CONNECTOR >
< PILOT LAMP >
CNP901 1-764-423-11 PIN, CONNECTOR 12P
PL901
PL902
< DIODE >
D901
D902
D903
D904
D905
8-719-420-90
8-719-422-64
8-719-422-64
8-719-422-64
8-719-422-64
DIODE
DIODE
DIODE
DIODE
DIODE
MA8051-M
MA8062-M
MA8062-M
MA8062-M
MA8062-M
< RESISTOR >
< IC >
IC901
8-759-443-68 IC LC75834JED
< CHIP CONDUCTOR >
JC902
JC951
JC952
1-216-295-00 SHORT
1-216-296-00 SHORT
1-216-296-00 SHORT
1-517-633-21 LAMP, PILOT (LCD BACK LIGHT)
1-517-633-21 LAMP, PILOT (LCD BACK LIGHT)
0
0
0
< LIQUID CRYSTAL DISPLAY >
LCD901 1-801-966-11 DISPLAY PANEL, LIQUID CRYSTAL
< SWITCH >
LSW901 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (OFF)
LSW902 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (SOURCE)
LSW903 1-762-619-11 SWITCH, KEY BOARD (WITH LED)
(MODE *)
LSW904 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (+ + ))
LSW905 1-762-619-11 SWITCH, KEY BOARD (WITH LED) (= 0 –)
R901
R902
R903
R904
R905
1-216-647-11
1-216-647-11
1-216-647-11
1-216-651-11
1-216-655-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
680
1K
1.5K
0.5%
0.5%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R906
R907
R908
R911
R921
1-216-655-11
1-216-659-11
1-216-663-11
1-208-806-11
1-216-647-11
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
1.5K
2.2K
3.3K
10K
680
0.5%
0.5%
0.5%
2%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R922
R923
R924
R925
R926
1-216-647-11
1-216-647-11
1-216-651-11
1-216-655-11
1-216-655-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
680
680
1K
1.5K
1.5K
0.5%
0.5%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R941
R942
R951
R952
R953
1-216-667-11
1-216-671-11
1-216-190-00
1-216-089-00
1-216-049-11
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
4.7K
6.8K
470
47K
1K
0.5%
0.5%
5%
5%
5%
1/10W
1/10W
1/8W
1/10W
1/10W
R954
R955
1-216-049-11 RES, CHIP
1-216-049-11 RES, CHIP
1K
1K
5%
5%
1/10W
1/10W
– 36 –
KEY
Ref. No.
Part No.
Description
Remark
R956
R962
R963
1-216-049-11 RES, CHIP
1-216-025-00 RES, CHIP
1-216-033-00 METAL CHIP
1K
100
220
5%
5%
5%
1/10W
1/10W
1/10W
R964
R965
R967
R968
R981
1-216-035-00
1-216-035-00
1-216-035-00
1-216-033-00
1-216-655-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
270
270
270
220
1.5K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R982
R983
R984
R999
1-216-663-11
1-216-671-11
1-216-081-00
1-216-308-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
3.3K
6.8K
22K
4.7
0.5%
0.5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< SWITCH >
SW951 1-762-937-11 SWITCH, ROTARY (D-BASS)
************************************************************
*
A-3313-396-A MAIN BOARD, COMPLETE
*********************
*
*
3-009-809-01 BRACKET (IC)
3-010-517-01 HEAT SINK (BUS NON) (E)
7-685-793-09 SCREW +PTT 2.6X8 (S)
< CAPACITOR >
C1
C2
C3
C4
C5
1-163-235-11
1-163-009-11
1-126-933-11
1-126-157-11
1-126-933-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
22PF
0.001uF
100uF
10uF
100uF
5%
10%
20%
20%
20%
50V
50V
10V
16V
10V
C6
C7
C8
C9
C10
1-164-232-11
1-164-232-11
1-164-232-11
1-163-251-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
100PF
0.001uF
5%
10%
50V
50V
50V
50V
50V
C11
C12
C13
C14
C16
1-126-160-11
1-163-009-11
1-163-251-11
1-164-232-11
1-164-232-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.001uF
100PF
0.01uF
0.01uF
20%
10%
5%
C17
C18
C19
C22
C23
1-163-009-11
1-163-059-00
1-164-222-11
1-124-584-00
1-124-234-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
0.001uF
0.01uF
0.22uF
100uF
22uF
10%
10%
C25
C26
C27
C101
C102
1-109-982-11
1-163-989-11
1-164-222-11
1-163-263-11
1-163-263-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.033uF
0.22uF
330PF
330PF
10%
10%
C104
C105
C106
C107
C108
1-164-232-11
1-164-489-11
1-163-227-11
1-163-227-11
1-126-163-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
C109
C121
C122
C123
1-163-251-11
1-163-809-11
1-164-492-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
20%
20%
50V
50V
50V
50V
50V
50V
50V
25V
10V
16V
5%
5%
10V
25V
25V
50V
50V
0.01uF
0.22uF
10PF
10PF
4.7uF
10%
0.5PF
0.5PF
20%
50V
16V
50V
50V
50V
100PF
0.047uF
0.15uF
0.1uF
5%
10%
10%
10%
50V
25V
16V
25V
Ref. No.
Part No.
Description
MAIN
Remark
C124
1-164-004-11 CERAMIC CHIP
0.1uF
10%
25V
C151
C152
C161
C162
C163
1-163-037-11
1-124-257-00
1-126-160-11
1-126-160-11
1-164-182-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
0.022uF
2.2uF
1uF
1uF
0.0033uF
10%
20%
20%
20%
10%
25V
50V
50V
50V
50V
C164
C165
C166
C167
C168
1-163-037-11
1-126-157-11
1-164-492-11
1-164-492-11
1-126-157-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.022uF
10uF
0.15uF
0.15uF
10uF
10%
20%
10%
10%
20%
25V
16V
16V
16V
16V
C169
C170
C171
C172
C181
1-163-227-11
1-163-157-00
1-126-163-11
1-163-009-11
1-126-163-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
10PF
10PF
4.7uF
0.001uF
4.7uF
0.5PF
5%
20%
10%
20%
50V
50V
50V
50V
50V
C182
C183
C191
C201
C202
1-163-009-11
1-163-251-11
1-163-251-11
1-163-263-11
1-163-263-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
100PF
100PF
330PF
330PF
10%
5%
5%
5%
5%
50V
50V
50V
50V
50V
C204
C205
C206
C207
C208
1-164-232-11
1-164-489-11
1-163-227-11
1-163-227-11
1-126-163-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.22uF
10PF
10PF
4.7uF
10%
0.5PF
0.5PF
20%
50V
16V
50V
50V
50V
C209
C251
C252
C261
C262
1-163-251-11
1-163-037-11
1-124-257-00
1-126-160-11
1-126-160-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
100PF
0.022uF
2.2uF
1uF
1uF
5%
10%
20%
20%
20%
50V
25V
50V
50V
50V
C263
C264
C265
C266
C267
1-164-182-11
1-163-037-11
1-126-157-11
1-164-492-11
1-164-492-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.0033uF
0.022uF
10uF
0.15uF
0.15uF
10%
10%
20%
10%
10%
50V
25V
16V
16V
16V
C268
C269
C270
C271
C272
1-126-157-11
1-163-227-11
1-163-227-11
1-126-163-11
1-163-009-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
10PF
10PF
4.7uF
0.001uF
20%
0.5PF
0.5PF
20%
10%
16V
50V
50V
50V
50V
C281
C282
C283
C301
C302
1-126-163-11
1-163-009-11
1-163-251-11
1-124-234-00
1-131-359-41
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
4.7uF
0.001uF
100PF
22uF
10uF
20%
10%
5%
20%
10%
50V
50V
50V
16V
25V
C303
C304
C305
C306
C331
1-163-251-11
1-164-004-11
1-107-823-11
1-164-232-11
1-124-584-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
100PF
0.1uF
0.47uF
0.01uF
100uF
5%
10%
10%
20%
50V
25V
16V
50V
10V
C332
C353
C354
C355
C356
1-124-234-00
1-163-251-11
1-126-157-11
1-126-157-11
1-126-934-11
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
22uF
100PF
10uF
10uF
220uF
20%
5%
20%
20%
20%
16V
50V
16V
16V
16V
C357
1-163-251-11 CERAMIC CHIP
100PF
5%
50V
– 37 –
MAIN
Ref. No.
Part No.
Description
C358
C359
C501
C502
1-163-251-11
1-164-489-11
1-163-235-11
1-163-234-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.22uF
22PF
20PF
5%
10%
5%
5%
50V
16V
50V
50V
Remark
C503
C504
C505
C551
C552
1-124-584-00
1-164-004-11
1-163-077-00
1-125-701-11
1-124-584-00
ELECT
CERAMIC CHIP
CERAMIC CHIP
DOUBLE LAYER
ELECT
100uF
0.1uF
0.1uF
0.047F
100uF
20%
10%
10%
10V
25V
25V
5.5V
10V
C553
C554
C571
C582
C602
1-164-004-11
1-164-004-11
1-126-163-11
1-163-009-11
1-164-222-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
4.7uF
0.001uF
0.22uF
10%
10%
20%
10%
25V
25V
50V
50V
25V
C611
C612
C613
C614
C615
1-126-157-11
1-126-157-11
1-163-077-00
1-126-157-11
1-126-157-11
ELECT
ELECT
CERAMIC CHIP
ELECT
ELECT
10uF
10uF
0.1uF
10uF
10uF
20%
20%
10%
20%
20%
16V
16V
25V
16V
16V
C616
C617
C621
C622
C623
1-126-157-11
1-126-157-11
1-126-157-11
1-163-133-00
1-124-589-11
ELECT
ELECT
ELECT
CERAMIC CHIP
ELECT
10uF
10uF
10uF
470PF
47uF
20%
20%
20%
5%
20%
16V
16V
16V
50V
16V
C701
C702
C703
C751
C752
1-163-077-00
1-163-077-00
1-163-077-00
1-126-096-11
1-107-682-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
10uF
1uF
10%
10%
10%
20%
10%
25V
25V
25V
35V
16V
C754
C755
C781
C782
C783
1-126-157-11
1-126-096-11
1-126-936-11
1-163-181-00
1-163-181-00
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
3300uF
100PF
100PF
20%
20%
20%
5%
5%
16V
35V
16V
50V
50V
C785
C786
C901
C903
C904
1-165-319-11
1-165-319-11
1-163-251-11
1-163-251-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
100PF
100PF
100PF
5%
5%
5%
50V
50V
50V
50V
50V
C906
C907
C908
C909
C910
1-163-009-11
1-163-009-11
1-163-251-11
1-163-181-00
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
100PF
100PF
100PF
10%
10%
5%
5%
5%
50V
50V
50V
50V
50V
C911
C912
C913
C914
1-163-181-00
1-164-182-11
1-164-004-11
1-164-004-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
0.0033uF
0.1uF
0.1uF
5%
10%
10%
10%
50V
50V
25V
25V
20%
Ref. No.
Part No.
Description
Remark
< DIODE >
D1
D21
D91
D301
D351
8-719-991-65
8-719-423-10
8-719-420-90
8-719-404-49
8-719-035-91
DIODE
DIODE
DIODE
DIODE
DIODE
SB02W03C
MA8100-M-TX
MA8051-M
MA111
MA4091-H (TA)
D352
D501
D551
D552
D553
8-719-404-49
8-719-400-20
8-719-400-20
8-719-404-49
8-719-404-49
DIODE
DIODE
DIODE
DIODE
DIODE
MA111
MA152WA
MA152WA
MA111
MA111
D571
D572
D582
D583
D601
8-719-034-94
8-719-110-03
8-719-057-80
8-719-422-76
8-719-423-32
DIODE
DIODE
DIODE
DIODE
DIODE
MA4180-M (QZ)
RD7.5ESB2
MA8160-M-TX
MA8075-M
MA8120-M
D621
D622
D701
D702
D703
8-719-035-54
8-719-911-19
8-719-035-77
8-719-035-77
8-719-035-74
DIODE
DIODE
DIODE
DIODE
DIODE
MA4039-M (TA)
1SS119
MA4068-L (TA)
MA4068-L (TA)
MA4062-M (TA)
D704
D705
D706
D707
D708
8-719-035-74
8-719-035-74
8-719-035-74
8-719-034-94
8-719-035-74
DIODE
DIODE
DIODE
DIODE
DIODE
MA4062-M (TA)
MA4062-M (TA)
MA4062-M (TA)
MA4180-M (QZ)
MA4062-M (TA)
D709
D721
D722
D723
D724
8-719-035-74
8-719-970-02
8-719-970-02
8-719-970-02
8-719-970-02
DIODE
DIODE
DIODE
DIODE
DIODE
MA4062-M (TA)
1SR139-400
1SR139-400
1SR139-400
1SR139-400
D731
D732
D733
D734
D781
8-719-970-02
8-719-970-02
8-719-970-02
8-719-970-02
8-719-049-38
DIODE
DIODE
DIODE
DIODE
DIODE
1SR139-400
1SR139-400
1SR139-400
1SR139-400
1N5404TU
D782
D783
D784
8-719-970-02 DIODE 1SR139-400
8-719-970-02 DIODE 1SR139-400
8-719-422-64 DIODE MA8062-M
< IC >
IC301
IC331
IC351
IC501
IC551
8-752-079-78
8-759-443-67
8-759-395-97
8-759-493-99
8-759-363-81
IC
IC
IC
IC
IC
CXA2509AQ-T4
LC75373ED
MM1322XFBE
uPD17707GC-529-3B9
XC61AN4002PR
IC611
IC751
8-759-347-49 IC BA3918-V2
8-759-490-48 IC HA13158
< CONNECTOR >
< JACK >
CN301
* CN351
CN701
CN781
1-766-260-11
1-506-995-11
1-764-422-11
1-774-701-11
CONNECTOR, FFC/FPC (ZIF) 7P
PIN, CONNECTOR (PC BOARD) 13P
PLUG, CONNECTOR 12P
PIN, CONNECTOR 16P
J1
J561
1-764-808-14 JACK (ANT) (ANT IN)
1-566-822-41 JACK (REMOTE IN)
< CHIP CONDUCTOR >
< CONPOSITION CIRCUIT BLOCK >
CP1
1-519-504-11 GAP, DISCHARGE
JC1
JC2
JC4
– 38 –
1-216-296-00 SHORT
1-216-295-00 SHORT
1-216-296-00 SHORT
0
0
0
MAIN
Ref. No.
Part No.
Description
Remark
JC151
JC161
1-216-296-00 SHORT
1-216-295-00 SHORT
0
0
JC162
JC163
JC251
JC301
JC302
1-216-295-00
1-216-296-00
1-216-296-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JC303
JC304
JC331
JC351
JC501
1-216-295-00
1-216-296-00
1-216-296-00
1-216-295-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JC502
JC503
JC504
JC506
JC507
1-216-295-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JC508
JC561
JC581
JC601
JC611
1-216-296-00
1-216-295-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JC751
JC752
JC781
JC902
JC903
1-216-296-00
1-216-296-00
1-216-295-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JC904
1-216-295-00 SHORT
0
1-410-509-11 INDUCTOR
1-411-669-12 COIL, CHOKE
1-410-509-11 INDUCTOR
Part No.
Description
Remark
< RESISTOR >
< COIL >
L501
L781
L901
Ref. No.
R1
R3
R4
R5
R6
1-216-049-11
1-216-061-00
1-249-429-11
1-216-081-00
1-249-429-11
RES, CHIP
METAL CHIP
CARBON
METAL CHIP
CARBON
1K
3.3K
10K
22K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/4W
1/10W
1/4W
R7
R8
R9
R10
R11
1-216-109-00
1-247-899-11
1-216-180-00
1-216-073-00
1-249-413-11
METAL CHIP
CARBON
RES, CHIP
METAL CHIP
CARBON
330K
680K
180
10K
470
5%
5%
5%
5%
5%
1/10W
1/4W
1/8W
1/10W
1/4W
R12
R13
R14
R21
R22
1-216-073-00
1-216-049-11
1-216-049-11
1-216-049-11
1-216-198-00
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
10K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/8W
R23
R24
R103
R104
R105
1-216-053-00
1-249-421-11
1-216-041-00
1-216-109-00
1-216-077-00
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
2.2K
470
330K
15K
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R106
R107
R108
R121
R122
1-216-079-00
1-249-429-11
1-216-081-00
1-216-200-11
1-216-081-00
METAL CHIP
CARBON
METAL CHIP
RES, CHIP
METAL CHIP
18K
10K
22K
1.2K
22K
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/8W
1/10W
R151
R152
R161
R171
R172
1-216-049-11
1-216-089-00
1-216-061-00
1-216-033-00
1-216-073-00
RES, CHIP
RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47K
3.3K
220
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R173
R174
R175
R181
R182
1-216-081-00
1-216-129-00
1-216-089-00
1-216-033-00
1-216-073-00
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP
22K
2.2M
47K
220
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R183
R184
R185
R186
R191
1-216-081-00
1-216-129-00
1-216-089-00
1-216-182-00
1-216-073-00
METAL CHIP
METAL CHIP
RES, CHIP
RES, CHIP
METAL CHIP
22K
2.2M
47K
220
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/8W
1/10W
R192
R203
R204
R205
R206
1-216-097-00
1-216-041-00
1-216-109-00
1-216-077-00
1-216-079-00
RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
470
330K
15K
18K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R207
R208
R251
R252
R261
1-216-222-00
1-216-081-00
1-216-049-11
1-216-089-00
1-216-061-00
RES, CHIP
METAL CHIP
RES, CHIP
RES, CHIP
METAL CHIP
10K
22K
1K
47K
3.3K
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/10W
1/10W
R271
R272
R273
R274
R275
1-216-033-00
1-216-073-00
1-216-081-00
1-216-129-00
1-216-089-00
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
220
10K
22K
2.2M
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R281
1-216-033-00 METAL CHIP
220
5%
1/10W
10uH
10uH
< TRANSISTOR >
Q21
Q22
Q171
Q181
Q271
8-729-120-28
8-729-021-94
8-729-920-21
8-729-920-21
8-729-920-21
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC1623-L5L6
2SK1657-T1B
DTC314TKH04
DTC314TKH04
DTC314TKH04
Q281
Q351
Q352
Q353
Q354
8-729-920-21
8-729-015-11
8-729-027-23
8-729-900-53
8-729-106-60
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC314TKH04
2SD1802FAST-TL
DTA114EKA-T146
DTC114EK
2SB1115A
Q355
Q551
Q571
Q581
Q582
8-729-900-53
8-729-027-23
8-729-120-28
8-729-900-53
1-801-806-11
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EK
DTA114EKA-T146
2SC1623-L5L6
DTC114EK
DTC144EKA-T146
Q583
Q601
Q602
Q603
Q621
8-729-027-38
8-729-423-99
8-729-900-53
8-729-027-23
8-729-027-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA144EKA-T146
2SD2137-OP
DTC114EK
DTA114EKA-T146
DTA114EKA-T146
Q622
8-729-120-28 TRANSISTOR 2SC1623-L5L6
– 39 –
MAIN
Ref. No.
Part No.
Description
R282
R283
R284
R285
1-216-073-00
1-216-081-00
1-216-129-00
1-216-089-00
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
10K
22K
2.2M
47K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
Remark
R286
R301
R302
R303
R304
1-216-033-00
1-216-079-00
1-216-097-00
1-216-065-00
1-216-077-00
METAL CHIP
METAL CHIP
RES, CHIP
METAL CHIP
METAL CHIP
220
18K
100K
4.7K
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R305
R306
R307
R308
R331
1-249-429-11
1-249-429-11
1-216-073-00
1-216-105-00
1-249-393-11
CARBON
CARBON
METAL CHIP
RES, CHIP
CARBON
10K
10K
10K
220K
10
5%
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/10W
1/4W
R351
R352
R353
R354
R501
1-216-049-11
1-249-385-11
1-216-065-00
1-216-073-00
1-216-097-00
RES, CHIP
CARBON
METAL CHIP
METAL CHIP
RES, CHIP
1K
2.2
4.7K
10K
100K
5%
5%
5%
5%
5%
1/10W
1/6W
1/10W
1/10W
1/10W
R502
R503
R504
R505
R506
1-216-097-00
1-216-097-00
1-216-097-00
1-216-097-00
1-216-057-00
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
METAL CHIP
100K
100K
100K
100K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R507
R508
R509
R510
R513
1-216-057-00
1-216-057-00
1-216-073-00
1-249-429-11
1-216-699-11
METAL CHIP
METAL CHIP
METAL CHIP
CARBON
METAL CHIP
2.2K
2.2K
10K
10K
100K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/4W
1/10W
R514
R516
R517
R518
R520
1-216-699-11
1-216-097-00
1-216-097-00
1-216-097-00
1-216-097-00
METAL CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
100K
100K
100K
100K
100K
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R522
R523
R524
R525
R526
1-216-097-00
1-216-097-00
1-216-097-00
1-216-097-00
1-216-097-00
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R527
R528
R530
R532
R534
1-216-097-00
1-216-097-00
1-216-097-00
1-216-097-00
1-216-097-00
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R535
R536
R537
R538
R539
1-216-097-00
1-216-246-00
1-216-246-00
1-216-097-00
1-216-097-00
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
100K
100K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/8W
1/8W
1/10W
1/10W
R540
R541
R542
R543
R544
1-249-421-11
1-249-421-11
1-249-421-11
1-249-421-11
1-216-057-00
CARBON
CARBON
CARBON
CARBON
METAL CHIP
2.2K
2.2K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/4W
1/4W
1/4W
1/4W
1/10W
R545
R546
R551
R552
1-249-429-11
1-249-413-11
1-216-097-00
1-216-057-00
CARBON
CARBON
RES, CHIP
METAL CHIP
10K
470
100K
2.2K
5%
5%
5%
5%
1/4W
1/4W
1/10W
1/10W
Ref. No.
Part No.
Description
Remark
R561
1-208-806-11 RES, CHIP
10K
0.50% 1/10W
R562
R563
R564
R571
R572
1-208-806-11
1-216-025-00
1-216-025-00
1-216-097-00
1-216-089-00
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
10K
100
100
100K
47K
0.50%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R573
R574
R575
R585
R586
1-216-089-00
1-249-421-11
1-216-073-00
1-216-113-00
1-216-073-00
RES, CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
47K
2.2K
10K
470K
10K
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R601
R602
R603
R621
R701
1-249-393-11
1-249-395-11
1-216-186-00
1-216-065-00
1-216-025-00
CARBON
CARBON
RES, CHIP
METAL CHIP
RES, CHIP
10
15
330
4.7K
100
5%
5%
5%
5%
5%
1/4W
1/4W
1/8W
1/10W
1/10W
R702
R703
R704
R705
R706
1-216-025-00
1-216-057-00
1-216-057-00
1-216-057-00
1-216-206-00
RES, CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES, CHIP
100
2.2K
2.2K
2.2K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/8W
R707
R708
R709
R710
R721
1-216-049-11
1-208-806-11
1-208-806-11
1-216-025-00
1-216-296-00
RES, CHIP
RES, CHIP
RES, CHIP
RES, CHIP
SHORT
1K
10K
10K
100
0
5%
0.50%
0.50%
5%
1/10W
1/10W
1/10W
1/10W
R722
R723
R724
R731
R732
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
R733
R734
R751
R752
R781
1-216-296-00
1-216-296-00
1-216-198-00
1-216-049-11
1-216-049-11
SHORT
SHORT
RES, CHIP
RES, CHIP
RES, CHIP
0
0
1K
1K
1K
5%
5%
5%
1/8W
1/10W
1/10W
< TUNER >
TU1
A-3282-031-A TUNER UNIT TUX-006/2 (EE)
< SWITCH >
S501
S551
1-571-478-11 SWITCH, SLIDE (POWER SELECT)
1-692-431-21 SWITCH, TACTILE (RESET)
< VIBRATOR >
X501
1-567-713-11 VIBRATOR, CRYSTAL (4.5MHz)
************************************************************
MISCELLANEOUS
***************
9
1-776-207-41 CORD (WITH CONNECTOR) (POWER)
F781
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) (10A)
HP901 1-500-157-21 HEAD, MAGNETIC (PLAYBACK)
M901
A-3291-665-A MOTOR ASSY, MAIN (CAPSTAN/REEL)
************************************************************
– 40 –
Ref. No.
Part No.
Description
Remark
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-621-772-10
7-685-793-09
7-685-792-09
7-685-794-09
7-685-106-19
SCREW +B 2X4
SCREW +PTT 2.6X8 (S)
SCREW +PTT 2.6X6 (S)
SCREW +PTT 2.6X10 (S)
SCREW +P 2X10 TYPE2 NON-SLIT
#6
7-624-104-04 STOP RING 2.0, TYPE-E
#7
7-627-553-17 PRECISION SCREW +P 2X2 TYPE 3
************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
1-473-067-71 REMOTE COMMANDER (RM-X4S)
3-861-693-11 MANUAL, INSTRUCTION
(HUNGARIAN, RUSSIAN)
3-861-694-11 MANUAL, INSTRUCTION, INSTALL
(HUNGARIAN, RUSSIAN)
3-921-278-01 LABEL (DSPL) (for RM-X4S)
X-3373-412-1 CASE (PANEL) ASSY (for FRONT PANEL)
************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS
***************************************
501
502
503
504
505
3-916-161-31
X-3370-077-1
X-3371-913-1
X-3373-432-1
1-776-207-41
FRAME ASSY
SCREW ASSY (AE. KEY), FITTING
SCREW ASSY (J)
BRACKET ASSY (For RM-X4S)
CORD (WITH CONNECTOR) (POWER)
502
501
503
504
505
– 41 –
XR-4803
Sony Corporation
9-925-681-11
Personal & Mobile Communication Company
– 42 –
98A05076-1
Printed in Japan © 1998. 1
Published by Quality Assurance Dept.
Download PDF

advertising