Sony GXD-L52H1 User's Manual

Sony GXD-L52H1 User's Manual
PROFESSIONAL FLAT DISPLAY MONITOR
GXD-L52H1
PROTOCOL MANUAL
1st Edition
Table of Contents
1.
Communication Parameters ......................................................... 1
2.
Pin Assignment ..................................................................................... 1
3.
Communication Data Format ....................................................... 1
4.
General Function ................................................................................. 3
5.
Analog Signal Detect Function ................................................... 8
6.
Priority Signal Select Function ................................................... 9
7.
Picture/Sound ...................................................................................... 14
8.
Size/Shift ................................................................................................. 17
9.
Status Enquiry ..................................................................................... 20
10. User Reset .............................................................................................. 25
11. Service ...................................................................................................... 25
GXD-L52H1
1. Communication Parameters
3. Communication Data Format
(a) Control message
Communication method
RS-232C
Synchronous method
Asynchronous
No.
Item
Value
Baud rate
9600bps
1
Header
0x8C: Control
Character length
8bit
2
Category
0xXX
Parity
None
3
Function
0xXX
Start bit length
1bit
4
Data1 (Length)
0xXX
Stop bit length
1bit
5
Data2 (Data1)
0xXX
Flow control
None
:
:
0xXX
:
:
0xXX
X
DataX
0xXX
X+1
Check Sum
0xXX
2. Pin Assignment
Monitor side (D-sub 9-pin)
5
4
9
3
8
2
7
1
6
_ External view _
Pin No.
1
2
3
4
5
6
7
8
9
Function
NC
TXD
RXD
NC
GND
NC
NC
NC
NC
Host side (D-sub 9-pin)
5
4
9
3
8
2
7
1
6
_ External view _
Pin No.
1
2
3
4
5
6
7
8
9
Function
NC
RXD
TXD
NC
GND
NC
NC
NC
NC
* Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a
value exceeds 255 (1byte).
* Set the command interval to 500 ms or more when transmitting the
Control command continuously.
* Set the command interval to 500 ms or more when transmitting the same
command (Enquiry) after the Control command.
(b) Enquiry message
No.
Item
Value
1
Header
0x83: Enquiry
2
Category
0xXX
3
Function
0xXX
4
Data1
0xFF
5
Data2
0xFF
6
Check Sum
0xXX
* Check Sum: Sum total of 1 to X. Lower one-byte data is validated when a
value exceeds 255 (1byte).
GXD-L52H1
1
4 Error answer
(c) Answer message
1 Control answer
No.
Item
Value
No.
Item
Value
1
Header
0xE0: Answer
1
Header
0x70: Answer
2
Answer*
0x00: No Function Error
2
Answer*
0x00: Completed
0x01: Check Sum Error
0x01: Limit Over
0x02: Data Length Error
0x02: Limit Under
0x03: Command Canceled
3
Check Sum
* 0x00: Completed
0x01: Limit Over
0x02: Limit Under
0x03: Command Canceled
* Check Sum:
0xXX
Packet is correctly received and process
is also correctly completed.
Packet is correctly received, but the data
value is over the upper limit.
Packet is correctly received, but the data
value under the lower limit.
Packet is correctly received, but the data
value is not correct or the request cannot
be accepted in the current host state.
Sum total of 1 to X. Lower one-byte data
is validated when a value exceeds 255
(1byte).
3
Check Sum
* 0x00: No Function Error
0x01: Check Sum Error
0x02: Data Length Error
0xXX
Packet header,category or function code are
not included in this protocol.
Check sum value or received packet is not
correct.
Packet is correctly received,but the data size
is over the upper limit.
2 Enquiry answer (Complete)
No.
Item
Value
1
Header
0x70: Answer
2
Answer
0x00: Completed
3
Return Data Size
0xXX
4
Return Data1
0xXX
:
:
0xXX
:
:
0xXX
X
Return DataX
0xXX
X+1
Check Sum
0xXX
* 0x00: Completed
* Return Data:
* Check Sum:
Packet is correctly received and process is also
correctly completed.
Returns the read value.
Sum total of 1 to X. Lower one-byte data is validated
when a value exceeds 255 (1byte).
3 Enquiry answer (Command cancel)
No.
Item
Value
1
Header
0x70: Answer
2
Answer
0x03: Command Canceled
3
Check Sum
0x73
0x03: Command Canceled
2
Packet is correctly received, but the data
value is not correct or the request cannot
be accepted in the current host state.
GXD-L52H1
4. General Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x00
Code Table (1-a) [a]
0x02
Code Table (1-a) [b]
0xXX
Enquiry
0x83
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (1-a) [b]
0xXX
Completed
Code Table (1-a)
[a]Function
0x00
0x01
0x02
Power
Input Select*4
Force Status Display
0x03
Audio Mute
0x04
Auto Status Display
[b]Range/Switch Code
0x00
OFF
0x01
ON
0x08
HD15 RGB
0x09
HD15 YUV
0x0E
OPTION RGB
0x0F
OPTION COMPONENT
0x20
DVI
0x30
VIDEO
0x31
S-VIDEO
0x44
HDMI
0x84
Option Digital1 (HDMI1/SDI)
0x85
Option Digital2 (HDMI2)
0x00
ON
0x01
OFF
0x00
OFF
0x01
ON
0x00
ON
0x01
OFF
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Enable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Enable
Enable
(Continued)
GXD-L52H1
3
Code Table (1-a)
[a]Function
0x06
0x0F
Color System
Language
[b]Range/Switch Code
0x00
Auto
0x01
NTSC
0x02
NTSC4.43
0x03
PAL
0x05
PAL-M
0x06
PAL-N
0x07
PAL60
0x00
Japanese
0x01
English
0x02
Deutsch
0x03
Français
0x04
Español
0x05
Italiano
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
0x10
Index Number
0x01-0xFF
Yes
Yes
Disable
Enable
0x12
Standby Power
0x00
Standard
Yes
Yes
Disable
Enable
0x01
Low
0x00
Off
Yes
Yes
Disable
Enable
0x01
ECO High
0x02
ECO Low
0x00
ON
Yes
Yes
Disable
Enable
0x01
OFF
0x00
H/Comp
Yes
Yes
Disable
Enable
0x01
Video
0x00
OFF
Yes
Yes
Disable
Enable
0x01
ON
0x00
FW12 (HD15)
No
Yes
Disable
Enable
0x02
FW11 (BNC)
0x03
Reserved
0x05
FW50 (RGB)
0x06
FW21 (UART + CTRL-S)
0x08
FW15 (HDMI x 2)
0x09
FW16 (HD-SDI)
0x0A
Reserved
0x0B
Reserved
0x0C
Reserved
0x13
ECO Mode
(Power Saving)
0x14
Speaker Out
0x18
Sync Mode
0x1B
0x24
Clock Display
Input Detect
(Option)
0x0D
Reserved
0x0E
Reserved
0x0F
Not Connect
(Continued)
4
GXD-L52H1
Code Table (1-a)
[a]Function
0x26
0x27
0x30
0x31
Auto Shut OFF
Auto Screen Adjust
PAP
Active Picture
0x32
Picture Size (P&P)
0x33
Sub Picture Size
(PinP)
0x34
0x35
0x36
Picture Position
(PinP)
PAP Input Detect
(Left/Main)
PAP Input Detect
(Right/Sub)
[b]Range/Switch Code
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
0x00-0x0E
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
No
Yes
Disable
Enable
No
Yes
Disable
Enable
0x00
OFF
0x01
ON
0x00
OFF
0x01
ON
0x00
OFF
0x01
P&P
0x02
PinP
0x00
Left (P&P)/Main (PinP)
0x01
Right (P&P)/Sub (PinP)
0x02
Swap
0x00
Large
0x01
Small
0x00
Position1
0x01
Position2
0x02
Position3
0x03
Position4
0x08
HD15 RGB
0x09
HD15 YUV
0x0E
OPTION RGB
0x0F
OPTION COMPONENT
0x20
DVI
0x30
VIDEO
0x31
S-VIDEO
0x44
HDMI
0x84
Option Digital1 (HDMI1/SDI)
0x85
Option Digital2 (HDMI2)
0x08
HD15 RGB
0x09
HD15 YUV
0x0E
OPTION RGB
0x0F
OPTION COMPONENT
0x20
DVI
0x30
VIDEO
0x31
S-VIDEO
0x44
HDMI
0x84
Option Digital1 (HDMI1/SDI)
0x85
Option Digital2 (HDMI2)
(Continued)
GXD-L52H1
5
Code Table (1-a)
[a]Function
0x40
0x41
Screen Saver
BackGround
[b]Range/Switch Code
0x00
OFF
0x01
All White ON
0x02
Sweep ON
0x00
Gray
0x01
Dark Gray
0x02
Black
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
0x43
Back Light
0x00-0x64
Yes
Yes
Disable
Enable
0x44
Logo Illumination
0x00
Logo Off
Yes
Yes
Enable
Enable
0x01
Logo On (Low)
0x02
Logo On (High)
0x00
Main + Remocon
Yes
Yes
Disable
Enable
Yes
Yes
Enable
Enable
Yes
Yes
Enable
Enable
Yes
Enable
Enable
Yes
Yes
Enable
Enable
No
Yes
Enable
Enable
0x45
Control Mode
0x46
On Off Timer Mode
0x47
On Timer Enable
0x48
0x65
0x66
Off Timer Enable
IP Setting Mode
IP Setting Execute
0x01
Main
0x02
Remocon
0x03
All Off
0x04
Limited*5
0x00
Every Day (Repeat)
0x01
Day Of Week
bit0
Sunday 1: Enable, 0: Disable
bit1
Monday 1: Enable, 0: Disable
bit2
Tuesday 1: Enable, 0: Disable
bit3
Wednesday 1: Enable, 0: Disable
bit4
Thursday 1: Enable, 0: Disable
bit5
Friday 1: Enable, 0: Disable
bit6
Saturday 1: Enable, 0: Disable
bit7
Every day 1: Enable, 0: Disable
bit0
Sunday 1: Enable, 0: Disable
bit1
Monday 1: Enable, 0: Disable
bit2
Tuesday 1: Enable, 0: Disable
bit3
Wednesday 1: Enable, 0: Disable
bit4
Thursday 1: Enable, 0: Disable
bit5
Friday 1: Enable, 0: Disable
bit6
Saturday 1: Enable, 0: Disable
bit7
Every day 1: Enable, 0: Disable
0x00
DHCP
0x01
Manual
0x02
Speed
0x00
Shut Down
0x01
IP Setting
0x02
NVR Reset
0x03
Alarm
Yes
(Continued)
6
GXD-L52H1
Code Table (1-a)
[a]Function
0x67
0x68
0x70
0x71
IP Setting Result
Speed Setting
Input Skip
Default Input
[b]Range/Switch Code
0x00
Done
0x01
Error 1 (UART Commu.)
0x02
Error 2 (Duplication)
0x03
Error 3 (IP Add Setting)
0x04
Error 4 (GW Add setting)
0x05
Error 5 (DNS1 Setting)
0x06
Error 6 (DNS2 Setting)
0x07
Error 7 (Sbnt Msk Setting)
0x00
100Mbps/Full Duplex
0x01
100Mbps/Half Duplex
0x02
10Mbps/Full Duplex
0x03
10Mbps/Half Duplex
0x04
Auto
bit0
HD15
bit1
DVI
bit2
HDMI
bit3
VIDEO
bit4
S-VIDEO
bit5
Reserved
bit6
Reserved
bit7
Reserved
0x00
Last Memory
0x01
Option
0x74
Digital Signal Detect
(DVI/HDMI/etc.) *6
0x00
VIDEO
0x01
PC
0x75
Signal Status*7
0x00
Stable
0x01
Unstable/No Signal
0x76
0x7A
0x7D
GXD-L52H1
VIDEO Signal Detect 0x00
Logo Position
Power Management
Mode*8
NTSC
0x01
PAL
0x00
Auto
0x01
Landscape
0x02
Portrait
0x00
OFF
0x01
ON
Command
Control
Enquiry
Standby
Power On
Yes
No
Enable
Enable
Yes
Yes
Enable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Enable
Enable
No
Yes
Disable
Enable
No
Yes
Disable
Enable
No
Yes
Disable
Enable
Yes
Yes
Enable
Enable
Yes
Yes
Disable
Enable
7
Code Table (1-a)
[a]Function
0x7E
On Screen Logo
0x7F
*4:
*5:
*6:
*7:
*8:
[b]Range/Switch Code
LED
0x00
OFF
0x01
ON (Default)
0x02
Reserved
0x00
OFF
0x01
ON
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Enable
Enable
Yes
Yes
Disable
Enable
Auto Signal Detect becomes Disable. When Option Slot is connected, Option command is Enable.
Restricts a part of keys operation following below.
[Remote Commander]
Menu, Picture, Sound, ECO (Power Saving), Contrast+/_,Brightness, Chroma, H Shift, V Shift, V size, PAP
[Main]
Menu
Digital Signal Status is Enable for Digital Input Signal Detect Function only in Stable.
Digital Signal or VIDEO Signal is Enable. Return Signal Status of Active Window.
Only the panel power supply is turned off at the standby when setting it “ON”.
5. Analog Signal Detect Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (1-a) [a]
Code Table (1-d)
0xFF
0xXX
Answer
Header
Answer
Return to Data Size
Return Data1
Data2
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (1-a) [b]
0xFF
0xXX
Completed
Code Table (1-a)
[a]Function
0x78
[b]Range/Switch Code
Analog Signal Detect 0x00
0x01
VIDEO
Command
Control
Enquiry
Standby
Power On
No
Yes
Disable
Enable
PC
Code Table (1-d)
Input Select
8
0x00
Main
0x01
Sub
0xFF
Present input
1-a[b]
When input is no signal or not supported signal, return value is Video(0x00).
GXD-L52H1
6. Priority Signal Select Function
(a) Mode Control
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (2-a) [a]
Code Table (2-d)
0xFF
0xXX
Answer
Header
Answer
Return to Data Size
Return Data1
Data2
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (2-a) [b]
0xFF
0xXX
Completed
Code Table (2-a)
[a]Function
0x77
[b]Range/Switch Code
Priority Signal Select
0x00
Input1 Auto
0x01
Input1 RGB
0x02
Input1 YPbPr
Command
Control
Enquiry
Standby
Power On
No
Yes
Disable
Enable
Code Table (2-d)
Input Select
0x00
HD15
0x01
Option
(b) Color Matrix
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Check Sum
Control
0x8C
0x00
Code Table
(1-b) [a]
0x04
Code Table
(1-c)
Code Table
(1-b) [b]
Code Table
(1-d)
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (1-b) [a]
Code Table (1-c)
Code Table (1-d)
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to
Data Size
Return Data1
Return Data2
Return Data3
Check
Sum
Enquiry
0x70
0x00
0x04
Code Table (1-c)
Code Table (1-b) [b]
Code Table (1-d)
0xXX
Completed
Code Table (1-b)
[a]Function
0x1D
GXD-L52H1
Color Matrix
[b]Range/Switch Code
0x00
YCbCr
0x01
YPbPr
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
9
Code Table (1-c)
Format Select
0x00
480P
0x01
1080i
0x02
720P
0x03
480i
Code Table (1-d)
Input Select
0x00
HD15 (Component)
0x01
Option
(c) Time Control
Data Set (Month, Date)
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
0x7C
0x03
Month: 0x01-0x0C
Date: 0x01-0x1F
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x7C
0xFF
0xFF
0xFD
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Month: 0x00-0x0C
Date: 0x01-0x1F
0xXX
Completed
Year Set
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x00
0x7B
0x02
Year: 0x00-0x63
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x7B
0xFF
0xFF
0xFC
10
GXD-L52H1
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Year: 0x00-0x63
0xXX
Completed
Clock Set (Hour, Minute)
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
0x22
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x22
0xFF
0xFF
0xA3
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Hour: *0x00-0x17
Minute: 0x00-0x3B
0xXX
Completed
Clock Set (Week)
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x00
0x23
0x02
Week: Code Table (1-e)
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
0x23
0xFF
0xFF
0xA4
GXD-L52H1
11
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Week: Code Table (1-e)
0xXX
Completed
Code Table (1-e)
Week Select
0x00
Sunday
0x01
Monday
0x02
Tuesday
0x03
Wednesday
0x04
Thursday
0x05
Friday
0x06
Saturday
On Timer, Off Timer
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x00
Code Table (1-f) [a]
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x00
Code Table (1-f) [a]
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Hour: 0x00-0x17
Minute: 0x00-0x3B
0xXX
12
Completed
GXD-L52H1
Code Table (1-f)
[a]Function
[b]Range/Switch code
On Timer
0x50
Sunday
_
0x51
Monday
_
0x52
Tuesday
_
0x53
Wednesday
_
0x54
Thursday
_
0x55
Friday
_
0x56
Saturday
_
0x57
Every day
_
Off Timer
0x58
Sunday
_
0x59
Monday
_
0x5A Tuesday
_
0x5B Wednesday
_
0x5C Thursday
_
0x5D Friday
_
0x5E Saturday
_
0x5F Every day
_
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
(d) IP Address Setting
IP Address
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x42
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Subnet Mask
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x61
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Gateway Address
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x62
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
DNS Primary
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x63
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
GXD-L52H1
13
DNS Secondary
Syntax
Header
Category
Function
Data1
Data2
Data3
Data4
Data5
Check Sum
Control
0x8C
0x00
0x64
0x05
Address 0
0x00-0xFF
Address 1
0x00-0xFF
Address 2
0x00-0xFF
Address 3
0x00-0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
IP Address ex)
192.128.14.1 →192 (0xC0) Address 0
128 (0x80) Address 1
14 (0x0E) Address 2
1
(0x01) Address 3
* IP address command can be carried out even in the standby state.
Code Table (1-a)
[a]Function
[b]Range/Switch code
0x42
IP Address
_
0x61
Subnet Mask
_
0x62
Gateway Address
_
0x63
DNS Primary
_
0x64
DNS Secondary
_
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Enable
Enable
7. Picture/Sound
(a) Picture/Sound
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x10
Code Table (2-a) [a]
0x02
Code Table (2-a) [b]
0xXX
Enquiry
0x83
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (2-a) [b]
0xXX
14
Completed
GXD-L52H1
Code Table (2-a)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
Contrast
0x00-0x64
Yes
Yes
Disable
Enable
0x01
Brightness
0x00-0x64
Yes
Yes
Disable
Enable
0x02
Chroma
0x00-0x32
Yes
Yes
Disable
Enable
0x03
Phase
0x00-0x64
Yes
Yes
Disable
Enable
0x04
Color Temp
0x00
Cool
Yes
Yes
Disable
Enable
0x01
Neutral
0x02
Warm
0x03
Custom
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
0x09
Sharpness
0x00-0x14
0x0A
NR
0x00
OFF
0x01
Low
0x0B
0x0C
0x0D
0x0E
0x10
Cinema Drive
Dynamic Picture
Color Correct
Gamma Correct
Picture Mode
0x02
Mid
0x03
High
0x00
Auto
0x01
OFF
0x00
OFF
0x01
ON
0x02
Reserve
0x00
ON
0x01
OFF
0x00
High
0x01
Mid
0x02
Low
0x00
Standard
0x01
Vivid
0x02
Custom
0x05
TC Control
0x06
Conference
0x30
Volume
0x00-0x64
Yes
Yes
Enable
Enable
0x31
Treble*1
0x00-0x64
Yes
Yes
Disable
Enable
0x32
Bass*1
0x00-0x64
Yes
Yes
Disable
Enable
0x33
Balance
0x00-0x64
Yes
Yes
Disable
Enable
0x34
Surround
0x00
OFF
Yes
Yes
Disable
Enable
0x01
Hall
0x02
Simulate
Yes
Yes
Disable
Enable
0x35
Sound Mode
0x00
Dynamic
0x01
Standard
0x02
Reserve
0x03
Custom
(Continued)
GXD-L52H1
15
Code Table (2-a)
[a]Function
[b]Range/Switch code
0x36
Default Volume Set 0x00-0x64
0x37
Volume Select
0x38
Max Volume Set
0x00
Last Memory
0x01
Default Setting
0x32
50
0x46
70
0x64
100
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Enable
Enable
Yes
Yes
Enable
Enable
Yes
Yes
Enable
Enable
*1 Sound Mode = Custom Only is Enabled.
(b) Color Temp
Syntax
Header
Category
Function
Data1
Data2
Data3
Check Sum
Control
0x8C
0x10
Code Table (2-b) [a]
0x03
Code Table (2-c)
Code Table (2-b) [b]
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x10
Code Table (2-b) [a]
Code Table (2-c)
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Code Table (2-c)
Code Table (2-b) [b]
0xXX
Completed
Code Table (2-b)
[a]Function
0x05
Red Gain
0x06
Green Gain
0x07
Blue Gain
[b]Range/Switch code
0x00-0x1E
Command
Control
Enquiry
Standby
Power On
Yes
Yes
Disable
Enable
Code Table (2-c)
Format Select
0x00
Cool
0x01
Neutral
0x02
Warm
0x03
Custom
16
GXD-L52H1
8. Size/Shift
(a) 8Bits Register
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x20
Code Table (3-b) [a]
0x02
Code Table (3-b) [b]
0xXX
Enquiry
0x83
0xFF
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x01
0x71
Limit Over
0x70
0x02
0x72
Limit Under
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (3-b) [b]
0xXX
Completed
Code Table (3-b)
[a]Function
[b]Range/Switch code
Command
Control
Enquiry
Standby
Power On
0x00
H Size
0x00-0x3C
Yes
Yes
Disable
Enable
0x01
H Shift
0x00-0x3C
Yes
Yes
Disable
Enable
0x02
V Size
0x00-0x0A
Yes
Yes
Disable
Enable
0x03
V Shift
0x00-0x3C
Yes
Yes
Disable
Enable
0x04
Aspect
0x00
Wide Zoom
(VIDEO Only)
Yes
Yes
Disable
Enable
0x01
Zoom
(VIDEO Only)
0x02
Full
(VIDEO Only)
0x04
Normal
(PC:Real, VIDEO: 4:3)
0x05
Full 1 (PC Only)
0x06
Full 2 (PC Only)
Yes
Yes
Disable
Enable
0x05
Multi Display
0x00
OFF
0x01
2x2
0x02
3x3
0x03
4x4
0x04
1x2
0x05
1x3
0x06
1x4
0x07
2x1
0x08
3x1
0x09
4x1
(Continued)
GXD-L52H1
17
Code Table (3-b)
[a]Function
[b]Range/Switch code
0x06
Auto Pixel Adjust
0xFF
0x07
Dot Phase
0x00-0x1F
0x0B
Multi Position
0x00
(2 x 2 ,1 x 2, 2 x 1)
0x01
*1
0x0C
0x0D
0x0E
0x0F
18
Execute
Position1
Position3
0x03
Position4
Position1
Position3
0x03
Position4
0x04
Position5
0x05
Position6
0x06
Position7
0x07
Position8
0x08
Position9
Multi Position
0x00
(4 x 4, 1 x 4, 4 x 1)
0x01
*1
Position1
Multi Display
Output Format
Standby
Power On
Yes
No
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Yes
Yes
Disable
Enable
Position2
0x02
Over Scan
Enquiry
Position2
0x02
Multi Position
0x00
(3 x 3, 1 x 3, 3 x 1)
0x01
*1
Command
Control
Position2
0x02
Position3
0x03
Position4
0x04
Position5
0x05
Position6
0x06
Position7
0x07
Position8
0x08
Position9
0x09
Position10
0x0A
Position11
0x0B
Position12
0x0C
Position13
0x0D
Position14
0x0E
Position15
0x0F
Position16
0x00
OFF
0x01
ON
0x02
AUTO
0x00
Tiles
0x01
Window
GXD-L52H1
*1 Arrangement of Multi Position.
Multi Position (2 x 2)
Multi Position (1 x 2)
1
2
1
3
4
2
Multi Position (3 x 3)
Multi Position (1 x 3)
1
2
3
1
4
5
6
2
7
8
9
3
Multi Position (4 x 4)
Multi Position (1 x 4)
1
2
3
4
1
5
6
7
8
2
9
10
11
12
3
13
14
15
16
4
GXD-L52H1
Multi Position (2 x 1)
1
2
Multi Position (3 x 1)
1
2
3
Multi Position (4 x 1)
1
2
3
4
19
9. Status Enquiry
(a) Model Name
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x00
0xFF
0xFF
0xB1
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (4-a)
0xXX
Completed
Code Table (4-a)
Format Select
0x26
GXD-L52H1
(b) Serial Number
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x01
0xFF
0xFF
0xB2
Answer Header
Answer
Return to
Data Size
Return Data1
Return Data2
Return Data3 Return Data4 Check Sum
Enquiry
0x00
0x05
Upper 8bit
Data
Middle Upper
Data
Middle Lower
Data
0x70
Lower 8bit
Data
0xXX
Completed
Return Data1-Data4: 0x00000000-0x0098967F (0,000,000-9,999,999)
(c) Operation Time
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x02
0xFF
0xFF
0xB3
Answer Header
Answer
Return to
Data Size
Return Data1
Return Data2
Return Data3 Return Data4 Check Sum
Enquiry
0x00
0x05
Upper 8bit
Data
Middle Upper
Data
Middle Lower
Data
0x70
Lower 8bit
Data
0xXX
Completed
Return Data1-Data4: 0x00000000-0xD693A3FF (0sec.-3,599,999,99sec.)
(d) Soft Version (Main CPU)
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x03
0xFF
0xFF
0xB4
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Check Sum
Enquiry
0x70
0x00
0x03
Upper 8bit Data
Lower 8bit Data
0xXX
Completed
Return Data1-Data2: 0x0000-0xFFFF (BCD Format)
ex) In Version0.100, it is set to 01 and 00.
20
GXD-L52H1
(e) 8bits Register
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
Code Table (4-b)
0xFF
0xFF
0xXX
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (4-b)
0xXX
Completed
Code Table (4-b)*
Function
Return Data
Unit
0x07
Digital 3.3 V
0x00-0xFF
0x08
Analog 24 V
0x00-0xFF
0x09
Digital 5 V
0x00-0xFF
0x0A
Temp1
0x00-0xFF
0x0B
Temp2
0x00-0xFF
0x0C
Temp3
0x00-0xFF
0x0D
Temp P/S
0x00-0xFF
0x0E
Inverter Alarm
0: Normal, 1: Abnormal
0x11
Shutdown Log
0x00-0xFF
0x12
Digital 3.3 V (Failure)
0x00-0xFF
0x13
Digital 5 V (Failure)
0x00-0xFF
0x14
Analog 12 V (Failure)
0x00-0xFF
0x16
Analog 12 V
0x00-0xFF
*
. For function 0x07, 0x08, 0x09, 0x10, 0x12, 0x13,
0x14 and 0x16 in the left table
When the display value is 3.0 V, “0x1E” (30) is
returned.
. For function 0x0A, 0x0B and 0x0C, 0x0D in the
left table
When the display value is 50 dC, “0x32” (50) is
returned.
When the display value is _20 dC, “0xEC” is
returned.
(f) Shutdown Log
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x11
0xFF
0xFF
0xC2
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Shutdown Log
Code Table (4-c)
0xXX
Completed
Return Data1: 0x00-0xFF
Code Table (4-c)
Shutdown Information
bit0
Reserved
bit1
1: FAN Sensor Abnormal
bit2
1: Panel Abnormal
0: Normal
bit3
1: Temperature Sensor Abnormal
0: Normal
bit4
Reserved
bit5
1: Power Abnormal (3.3 V, 5 V)
0: Normal
bit6
1: Analog Power Abnormal (12 V, 9 V, 5 V)
0: Normal
bit7
Reserved
GXD-L52H1
0: Normal
21
(g) Auto Input Detect
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x30
0xFF
0xFF
0xE1
Answer Header
Answer
Return to
Data Size
Return Data1
Return Data2
Return Data3
Return Data4
Return Data5
Enquiry
0x00
0x0C
Input1
Input Type
Code Table
(4-e)
Input2
Input Type
Code Table
(4-e)
Input3
Input Type
Code Table
(4-e)
Input4
Input Type
Code Table
(4-e)
Input5
Input Type
Code Table
(4-e)
Return Data6
Return Data7
Return Data8
Return Data9
Return Data10
Option1
Option Type
Code Table
(4-e)
Option1
Input Type
Code Table
(4-e)
Option2
Option Type
Code Table
(4-e)
Option2
Input Type
Code Table
(4-e)
Option3
Option Type
Code Table
(4-e)
0x70
Return Data11 Check Sum
Option3
Input Type
Code Table
(4-e)
0xXX
Completed
Code Table (4-e)
Input
Input Type (Basic)
INPUT1
0x06
RGB/YUV (Analog)
INPUT2
0x07
DVI
INPUT3
0x00
No Input
INPUT4
0x00
No Input
INPUT5
0x00
No Input
OPTION1
Option Type
Input Type (Option)
0x00
Analog Only
0x00
No Input
0x00
Analog Only
0x03
Video/S-Video
0x00
Analog Only
0x06
RGB/YUV (Analog)
0x00
Analog Only
0x07
Video/S-Video/RGB/YUV (Analog)
0x01
Analog/Com
0x04
RGB
0x03
Com Only
0x00
No Input
0x04
Digital Only
0x0E
Digital/Digital
0x04
Digital Only
0x0D
Digital
OPTION2
0x00
Analog Only
0x00
No Input
OPTION3
0x00
Analog Only
0x00
No Input
22
GXD-L52H1
(h) Auto Plug Detect
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x32
0xFF
0xFF
0xE3
Answer
Header
Answer
Return to Data Size
Return Data1
Return Data2
Return Data3
Enquiry
0x70
0x00
0x21
Panel Type
Code Table (4-h)
H_Resolution (H)
Code Table (4-i)
H_Resolution (L)
Code Table (4-i)
Return Data4
Return Data5
Return Data6
Return Data7
V_Resolution (H)
Code Table (4-i)
V_Resolution (L)
Code Table (4-i)
Input Quantity
Code Table (4-j)
Input1
Input Type
Code Table (4-e)
Return Data8
Return Data9
Return Data10
Return Data11
Input2
Input Type
Code Table (4-e)
Input3
Input Type
Code Table (4-e)
Input4
Input Type
Code Table (4-e)
Input5
Input Type
Code Table (4-e)
Return Data12
Return Data13
Return Data14
Return Data15
Option Slot Quantity
Code Table (4-j)
Option1
Option Type
Code Table (4-e)
Option1
Input Type
Code Table (4-e)
Option2
Option Type
Code Table (4-e)
Return Data16
Return Data17
Return Data18
Return Data19
Option2
Input Type
Code Table (4-e)
Option3
Option Type
Code Table (4-e)
Option3
Input Type
Code Table (4-e)
(Reserve)
0xFF
Return Data20
Return Data21
Return Data22
Return Data23
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
Return Data24
Return Data25
Return Data26
Return Data27
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
Return Data28
Return Data29
Return Data30
Return Data31
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
(Reserve)
0xFF
Return Data32
Check Sum
(Reserve)
0xFF
0xXX
GXD-L52H1
23
(i) Auto Panel Type Detect
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0x30
0x31
0xFF
0xFF
0xE2
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (4-h)
0x72
Code Table (4-h)
Code Table (4-i)
Panel Type
0x00
LCD
Completed
Code Table (4-j)
H_Resolution
0x0780 (1920)
Input Quantity
0x05
V_Resolution
0x0438 (1080)
Option Slot Quantity
0x01
Code Table (4-d)
[a]Function
[b]Range/Switch code
0x00
Model Name
0x26
0x01
Serial Number
0x000
0x02
Operation Time
0x00000000-0x15751BF0
(0sec.-359,996,400sec.)
0x03
Soft Version (Main)
0x0000-0x9999
0x07
Digital 3.3 V
0x00-0xFF
0x08
Analog 24 V
0x00-0xFF
0x09
Digital 5 V
0x00-0xFF
0x0A
Temp1
0x00-0xFF
0x0B
Temp2
0x00-0xFF
0x0C
Temp3
0x00-0xFF
0x0D
Temp P/S
0x00-0xFF
0x0E
Inverter Alarm
0: Normal, 1: Abnormal
0x11
Shutdown Log
0x00-0xFF
0x12
Digital 3.3 V (Failure)
0x00-0xFF
0x13
Digital 5 V (Failure)
0x00-0xFF
0x14
Analog 12 V (Failure)
0x00-0xFF
0x16
Analog 12 V
0x00-0xFF
0x30
Auto Input Detect
0x31
Auto Panel Type Detect
24
Command
Control
Enquiry
Standby
Power On
No
Yes
Enable
Enable
GXD-L52H1
10. User Reset
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x50
Code Table (5)
0x02
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
Code Table (5)
Function
Range/Switch code
0x00
Picture Reset
0x01
Audio Reset
0x02
Size Reset
Size, Shift
0x03
Picture Reset2
(FW50)
Contrast, Brightness,
Chroma, Phase
0x04
All Reset
Command
Control
Enquiry
Standby
Power On
Yes
No
Disable
Enable
11. Service
(a) Mode
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0xF0
Code Table (6)
0x02
0xFF
0xXX
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Enquiry
0x83
0xF0
0x00
0xFF
0xFF
0x71
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
Answer
Header
Answer
Return to Data Size
Return Data1
Check Sum
Enquiry
0x70
0x00
0x02
Code Table (7)
0xXX
Completed
Code Table (6)
Function
Range/Switch code
Command
Control
Standby
Power On
Normal Mode Service Mode
0x00
Service Mode IN
Yes
Yes
Yes
Enable
Enable
0x01
Service Mode Exit
Yes
Yes
Yes
Disable
Enable
GXD-L52H1
25
Code Table (7)
Function
Range/Switch code
0x00
User Mode
0x01
Service Mode
Command
Enquiry
Standby
Power On
Normal Mode Service Mode
Yes
Yes
Yes
Disable
Enable
(b) Factory Reset
Syntax
Header
Category
Function
Data1
Data2
Check Sum
Control
0x8C
0x40
Code Table (8)
0x02
0xFF
0xXX
Answer
Header
Answer
Check Sum
Control
0x70
0x00
0x70
Completed
0x70
0x03
0x73
Command Canceled
Code Table (8)
Function
0x88 Factory Reset
26
Range/Switch
code
Command
Control
Enquiry
Standby
Power On
Normal Mode Service Mode
Yes
No
No
Yes
Disable
Enable
GXD-L52H1
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen
Ausrüstung
ohne
ausdrückliche
schriftliche Erlaubnis der Sony Corporation.
GXD-L52H1
GXD-L52H1 (WW) E
9-968-408-01
Sony Corporation
Printed in Japan
2008. 1 22
©2008
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement