Sony | KDL-40W3000 | User's Manual | Sony KDL-40W3000 User's Manual

3-212-601-11(1)
KDL-40W3000
KDL-46W3000
KDL-52W3000
1
Your New
™
BRAVIA
Flat-panel LCD HDTV
Congratulations! Your new BRAVIA™ TV opens the door to the “Full HD Experience”.
This guide will explain how to get the most from your new High Definition TV.
Quick Setup Guide
For further information, see the Operating Instruction Manual supplied with the TV.
Please retain this guide for your future reference.
Learn more. Visit the Sony HDTV Learning Center www.sony.com/HDTV
Please take these steps before you power up your BRAVIA™:
■ Register online at:
www.sony.com/registration (from U.S.A.)
www.SonyStyle.ca/registration (from Canada)
■ Make sure you’ve removed all accessory contents from packaging.
■ Install 2 AA batteries (supplied separately) in your remote control.
■ Determine whether you will hang your TV on a wall or place it on a floor stand. Sony
wall mounting brackets are designed to provide the best fit.
■ Give your TV 2 3/8 inches (6 cm) of space behind it to properly ventilate.
The Four Steps to a Full HD Experience: Set, Sound, Source,
and Setup
Along with your BRAVIA™ TV set, a complete HD system requires an HD sound system, a
source of HD content, and proper setup connection with components such as your HD
cable or satellite box.
You must get HD programming to experience the full detail of HDTV.
The quality of the image you see on your BRAVIA™ can only be as high as the quality of the
signal it is displaying. This chart shows the different signal types and how to access them.
Comments
For Your Convenience
Contact Sony Customer Support at:
http://www.sony.com/tvsupport
Or to speak with a support representative:
United States
Canada
1-800-222-SONY (7669) 1-877-899-SONY (7669)
Please Do Not Return the Product to the Store
©2007 Sony Corporation
Printed in U.S.A.
Sources
High Definition
Content
Best picture quality 16:9
aspect ratio
HD Over-The-Air Antenna
HD Cable Subscription/
Programming
HD Satellite Subscription
Digital Content
Good picture quality
aspect ratio based on
program
Over-The-Air Antenna
Digital Cable Subscription
Digital Satellite
Subscription
Analog Content
Original TV format 4:3
aspect ratio
Over-The-Air Antenna
Cable Subscription
Contact your cable or satellite provider to upgrade your service to HD. Receive over-the-air
HD broadcasts with an HD-quality antenna (www.antennaweb.org) and discover the wealth
of entertainment now available on super-high-resolution Blu-ray Disc™.
1 Select the language for the OSD (on-screen display).
To Access Initial Setup by Remote Control
If you did not follow the Initial Setup screen the first time, press HOME on your remote
control to display TV Home Menu/XMB™ and select the Initial Setup icon under the
Settings category.
Step 1 of 5
Initial Setup
1 XMB™ appears.
Please select a language. Language settings will apply to
on screen display as well as default audio for digital
channels. Highlight a choice and press
to continue.
See reverse side of this guide for sample connection diagrams.
■
■
Turn off and unplug all components before making connections.
Do not turn on the TV until connection setup is completed.
Audio/Video
Performance
Input
Connector
Video Connection
HDMI 1
HDMI 2
HDMI 3
HDMI connection*
Audio Connection
High or Standard Definition Quality
HDMI cable carries both video and audio signals.
Separate audio cable is not needed.
(*When HDMI is connected to DVI with an adapter,
a separate audio L/R is necessary.)
Component 1
Component 2
1080/24p, 1080p, 1080i, 720p, 480p, 480i, PC
(Compatible with HD or SD content)
1080p, 1080i, 720p, 480p, 480i
(Compatible with HD or SD content)
Component connection
Audio L/R
S VIDEO connection
Audio L/R
Composite video connection
Audio L/R
Video 1
480i
(SD content)
(Use this connector in place of composite video connector)
Video 1
Video 2
Video 3
What is HDMI™?
HDMI (High-Definition Multimedia Interface) cables are the standard for connecting HDTV. They are built to properly handle high bandwidth, uncompressed video and multi-channel
audio—all in one cable.
Connecting a PC to Your BRAVIA™
■ May require DVI-to-HDMI adapter and separate audio connector.
■ Connect PC’s audio output when using a Digital Video Interface (DVI) or HD15 connection.
■ Press PC’s FUNCTION Key + Select Output to transmit to TV.
■ When using an HD15 connection, adjust TV’s Pitch and Phase to correct sharpness.
■ Refer to your BRAVIA™ Operating Instruction Manual for more information.
■ Connect with an HDMI cable when using an HDMI compatible PC.
To learn more about HDTV, visit www.sony.com/HDTV
4 Watching Your TV
3 Running Initial Setup
Initial Setup instructions are displayed on the screen when your BRAVIA™ is powered on
for the first time.
Your BRAVIA™ TV must be properly connected to components such as sound system and cable or satellite box.
(Shown with video and audio connectors)
Best Signal
Performance
Please contact Sony directly if you have questions on the use of your television
after reading your Quick Setup Guide and Operating Instruction Manual.
2 Connecting Your TV
HDMI Settings
Select Your Content Source
XMB™ with focus on Settings. Select
Settings to customize your TV.
Whether you are watching cable, satellite or broadcast TV; playing a VCR, DVD or Blu-ray
Disc™; or connecting to your PC, you need to choose the correct input using your remote
control:
■ Press HOME on your remote control to display on-screen the TV mode or External
Inputs selection menu; OR
■ Press INPUT repeatedly until your selection is highlighted on-screen.
Product Support
Clock/Timers
Sound
General
Screen
English
Adjust Screen Shape and Aspect Ratio
Español
Français
1.2.3
2 Connect either Antenna or Cable to your TV.
Step 2 of 5
Initial Setup
Auto Program allows the TV to tune channels directly from your
cable or antenna feed. If you are using only a cable or satellite
set top box, it is not necessary to run Auto Program. In this case,
choose “Skip”. Auto Program may take 30+ minutes to complete.
If you are not using the VHF/UHF/CABLE
connection to TV, you can cancel the Auto
Program by selecting the Skip option.
VHF/UHF/CABLE
Auto Program
Select Auto Program to advance to the
Auto Programming.
Skip
3 Your TV will detect the type of signal connected and will start scanning for the channels.
Initial Setup
TV
2 Select Initial Setup icon.
Settings
Start Initial Setup now?
Some channels may be overwritten.
1.2.3
Yes
No
Step 3 of 5
Please allow 30+ minutes to complete.
Pressing
or will cancel auto program.
Channels Found
Analog:
58
Digital:
0
Customize Sound and Picture Quality
Searching...
4 Follow on-screen instructions to complete setup and begin viewing your TV.
Step 5 of 5
Initial Setup
Select “OK” to use your TV
OK
High Definition and Standard Definition signals are transmitted with different aspect ratios
(the width-to-height shape of the image). Most HD signals use a widescreen aspect ratio of
16:9. Most SD signals use a boxy 4:3 aspect ratio. The 16:9 aspect ratio looks perfect on your
BRAVIA™, but a 4:3 image must be adjusted to look right. You can:
■ Adjust your TV so boxy 4:3 images are automatically re-configured (zoomed or
stretched) to fit the wide TV screen; OR
■ Watch SD content in its original, boxy format with wide black bars surrounding the
image to fill in unused space (for example, you may prefer to watch an old classic
movie in its original 4:3 format, not reconfigured for a wide screen).
■ Press WIDE on your remote control to display the Wide Mode setting of your
preference.
■ Visit
www.learningcenter.sony.us/HomeAudioandVideo/Televisions/Research1/TheBasicsofDTV
for more information.
To Do List
When the Initial Setup is completed, consider carrying out these items:
Set Clock
Set Closed Captions (CC)
Set Parental Lock
Show/Hide Channels
Label Inputs (skip inputs)
Speakers On/Off
For details, refer to your BRAVIA™ Operating Instruction Manual.
You can choose optimum sound and picture settings to match the content you are
displaying on your TV:
■ Press HOME on your remote control and select Picture or Sound. Choose the
appropriate setting for your content.
■ Use the OPTIONS button on your remote control to quickly adjust sound and picture
quality.
■ Refer to your BRAVIA™ Operating Instruction Manual for more information.
To learn more about HDTV, visit www.sony.com/HDTV
Video Options
TV
WIDE
XMB™ with focus on TV. Select the
channels from here or use the 0-9 number
buttons on your remote control.
7
INPUT
8
Cable
8.1
KFMB-DT
9
OPTIONS
HOME
10
10.1
TV
11
XMB™ with focus on External Inputs.
Select connected device from here or use
the INPUT button on your remote control.
Video2
Video3
Component2
HDMI1
HDMI2
TV
HD Basic Connection
HD Basic Connection with A/V Receiver
Cable/Antenna
HD Basic Connection with Home Theater System
Cable/Antenna
Rear of TV
PC IN
IN
1
3
RGB
Splitter
Splitter
VHF/UHF/CABLE
L
AUDIO
AUDIO
R
Rear of TV
Rear of TV
PC IN
1
IN
IN
1
1
1
3
VHF/UHF/CABLE
3
Blu-ray Disc™/DVD
S VIDEO
PB
VIDEO
PR
L
RGB
VHF/UHF/CABLE
L
AUDIO
DMex/SERVICE
DIGITAL
OUT
(OPTICAL)
(MONO)
L
L
AUDIO
AUDIO
AUDIO
R
R
R
AUDIO
L
AUDIO
HD Antenna
2
Y
RGB
PC IN
3
COMPONENT IN
VIDEO IN
(1080p/1080i/
(1080p/1080I/
720p/480p/480I)
720p/480p/480i)
R
AUDIO OUT
(VAR/FIX)
AUDIO
R
Blu-ray Disc™/DVD
Blu-ray Disc™/DVD
1
3
S VIDEO
PB
VIDEO
PR
L
2
HD Cable Box
or HD Satellite
Receiver
SAT
(dish)
DMex/SERVICE
Cable/SAT (dish)
DIGITAL
OUT
(OPTICAL)
(MONO)
L
L
AUDIO
AUDIO
AUDIO
R
R
VIDEO IN
SAT
(dish)
1
Y
SD Cable Box or
SD Satellite Receiver
R
COMPONENT IN
(1080p/1080i/
(1080p/1080I/
720p/480p/480I)
720p/480p/480i)
AUDIO OUT
(VAR/FIX)
HD Cable Box
or HD Satellite
Receiver
A/V Receiver
Home Theater System
Required Cable Types for Connection
Coaxial
■
Mini-Pin Audio
DVI-to-HDMI
■
Composite
HDMI
■
■
■
Audio (L/R) with Mini-Pin
HD15
Audio (L/R)
Component
Digital Optical Audio
Basic Connection with SD VCR/DVD
Notes on Connection:
Your TV is equipped with three HDMI inputs, connect your incoming signal source (HD Cable Box, HD Satellite Receiver, or DVD) with an HDMI or component video for the best
possible picture quality.
If your connecting equipment has DVI output instead of the HDMI output, you must use DVI-to-HDMI cable for the video and also connect an audio cable for the sound. If this is the
case, connect the cable to HDMI IN 1 (input) of your TV.
P&P/PIP functions require VHF/UHF/CABLE connection.
When receiving High-Definition content signal by over-the-air antenna, it is best to use the HD antenna.
When using a DVI-to-HDMI cable, make sure to connect the DVI side first.
Programming the Remote Control
PC Connection
Cable/Antenna
Your remote control can be programmed to use other
equipment. The remote control is preset as below for Sony
equipment.
Cable/Antenna
Splitter
Splitter
2
Rear of TV
1
3
1
2
S VIDEO
DMex/SERVICE
PB
VIDEO
PR
L
(MONO)
L
L
AUDIO
AUDIO
AUDIO
R
R
R
VIDEO IN
VHF/UHF/CABLE
PC IN
DIGITAL
OUT
(OPTICAL)
COMPONENT IN
(1080p/1080i/
(1080p/1080I/
720p/480p/480I)
720p/480p/480i)
IN
1
3
3
RGB
AUDIO
(VAR/FIX)
751 (Sony DVD Player)
STB
801 (Sony Satellite Receiver)
Programming Non-Sony Video Equipment
Follow the steps below to program your TV’s remote control.
found on the Manufacturer’s Codes List (see Operating Instructions).
If more than one code is listed, try entering the code listed first.
Code No. ______________
,
or
and
simultaneously to light the FUNCTION
not entered within 10 seconds, you must repeat step 2.
4Press
Notebook PC
HD Cable Box or
HD Satellite Receiver
VCR/DVD Combo
101 (Sony Blu-ray Disc Player)
DVD
3Enter the three-digit code using - while the selected button is lit. If the code is
R
DVD
BD
button.
L
AUDIO
SAT
(dish)
Programmable Code Number
2Press and hold
VHF/UHF/CABLE
AUDIO OUT
Sony Equipment
1In the space provided below, write down the three-digit code of your equipment
PC
Rear of TV
Y
VCR
Or
2
4
while the FUNCTION button is lit.
If programmed correctly the selected FUNCTION button blinks twice. If not it blinks
five times.
To Confirm the Programming
If you can turn on and off the equipment by pressing the green
programming is complete. If not, try the next code listed.
Note:
■
■
button, then the
In some cases, you may not be able to program your remote control. If this is the
case, use your equipment’s own remote control.
Any one of the FUNCTION buttons can be programmed to operate other
equipment regardless of the labeling. For example, if programmed with the correct
code,
can operate DVD/VCR combo equipment. This is useful if your
equipment does not match the labeled buttons available. Make note of your
equipment’s programmed button.
Download PDF

advertising